Search Documents

By E. A. Cappelen Smith

FOR distinguished service in the art of hydrometallurgy, the Mining and Metallurgical Society of America presented its gold medal to E. A. Cappelen Smith, at a dinner held in the Hotel Commodore, New York, on Nov.' 10, 1920. Prof. Waldemar Lindgren, president of the society, in giving the medal, said: "By the advancement of the science of hydrometallurgy, by the construction of plants on a scale audacious in their conception, by the successful overcoming of all sorts of difficulties, you have placed your name among those who occupy the very front rank among the hydrometallurgists. In recognition of this distinguished contribution to the science of metallurgy, the Mining and Metallurgical Society of America now awards you its gold medal."

Jan 1, 1920

By P. Lelong, P. Lacombe, J. Herenguel

IN previous studies on the effect of orientation on the rate of anodic oxidation of A1-3 pct Mg mono-crystals of high purity, certain anomalies were observed on the cold-worked metal. These anomalies were shown to correspond to regions of changed orientation within the grains resulting from plastic deformation.' In fact, they are deformation bands revealed by differences in rate of oxidation and produced by more or less continuous bending of the lattice about a [Ill] axis common to the original crystal and the band.2,3 Preliminary observations made after relatively large degrees of cold working revealed an approximate twin relationship between the bands and the surrounding crystal. Fig. 1 shows the etch figures formed on such a band and on the original monocrystal after a 67 pct rolling reduction. It is evidently not a true twinning, since there is a broad transition zone between the two systems, however the two extreme orientations are nearly in a twin relationship. It was decided to investigate these preliminary observations by progressive rolling-reductions on monocrystals of varied initial orientation. From these studies, which form the subject of the present article, it became apparent that the initial observation of an approximate twin relation between the bands and the monocrystal was simply a special case. Our experiments show that deformation in rolling proceeds by a mechanism analogous to those which have already been observed in the simpler cases of tension and compression. Micrography—in particular, the formation of etch figures—has been applied to the quantitative study of these orientations. In addition, observations have been made of slip lines, of thin oxide films yielding interference colors, of thick films in polarized light, and of etchants giving "engraving." These micrographic methods for studying orientation have established the orientation relationship without any ambiguity, whereas X-ray methods would have given only a statistical result because we were often dealing with thin bands (2 to 100 microns) and even narrower connecting zones covering a maximum of 20 microns. Specimen Preparation and Methods The Al-3 pct Mg alloy was prepared from 99.95 pct A1 and is of the type used industrially in France for brilliant anodized finishes under the name of Brillalumag. This material combines the normal commercial properties with an enduring brilliance due to the protection of a thick, but perfectly transparent, film of alumina.' The monocrystals were prepared by the method of critical deformation followed by prolonged annealing. Great care was taken to insure perfect homogeneity of composition, to eliminate included crystals,6,7 and to avoid the formation of undulations during oxidation. The critical deformation for this alloy is about 1.2 pct (1-l0/10x100) and the subsequent annealing was for one week at 500 °C after gradual increase of temperature (35°C per hr). The crystals thus prepared had a section of 10x5 mm and a length of 20 to 40 mm. Each of these crystals was polished electrolytically and etched for the formation of etch-figures with the classical reagent.' The orientation was then calculated from their angles, as measured with a goniometer microscope.

Jan 1, 1954

By P. A. Beck, S. Kohara, M. N. Parthasarathi

IT has been shown1,3 that many observed phenomena related to annealing textures in f.c.c. metals can be adequately accounted for, at least in a qualitative way, by considering the orientation dependence of the boundary mobility, without any hypotheses concerning preferred orientation of nuclei. It was noted1 that this approach is particularly successful in the common cases of primary recrystallization in highly cold-worked polycrys-talline metals, where nuclei occur in great abundance, and that in the other extreme case, where the number of nuclei is very limited, or even only a single crystal is grown, the orientation dependence of boundary mobility has only a small effect, or none at all, on the orientations resulting from annealing. Recently Dunn described examples3-6 where observed secondary recrystallization textures apparently cannot be accounted for on the basis of oriented growth alone, but also require oriented nuclei, or at least the absence of nuclei in certain orientation ranges. In general, the great difficulty in correlating the preferred orientation of recrystallized grains with that of nuclei is inherent in the fact that nuclei are by nature very small, and that they are usually identifiable as "nuclei" only after growth, i.e., after they have already been subject to growth selectivity. An investigation was carried out by Liebmann and Lücke,' and also a very similar one by Graham and Cahn,' to obtain quantitative information on the orientation depend- ence of boundary migration rates in the recrystallization of slightly deformed aluminum single-crystal rods or plates, in which artificially nucleated recrystallized grains of predetermined orientation were grown. Liebmann and Lücke foupd maximum boundary mobility for boundaries across which the misorientation corresponded to a rotation of 40 deg around a common [Ill] axis, in accordance with earlier conclusions.9,1 Also, they confirmed that such an orientation relationship predominates among crystals growing into slightly extended single crystals from presumably random artificial nuclei. On the other hand, Graham and Cahn found no preferred orientation among crystals grown in a similar manner. It is not as yet known how these observations may be reconciled with each other. The view has been expressed in various papers5'10,21 that selective growth based on the orientation dependence of boundary mobility is not in itself sufficient to account for the formation of sharp re-crystallization textures, such as those often observed in highly deformed polycrystalline metals after annealing. The present work was undertaken to ascertain whether or not it is possible to obtain a sharp re-crystallization texture in a case where random nuclei are assuredly present in large numbers. It was previously found1' that high-purity aluminum crystals rolled 80 pct on the (110) plane in the [1T2] direction, when suitable precautions are taken, may be annealed for periods of about 1000 sec at 350°C without recrystallization. It was also found that the reluctance to recrystallize in this case is due to the scarcity of material in sufficiently deviating orientations to serve as nuclei. By using such a matrix,

Jan 1, 1959

By RAY LYMAN WILBUR

SINCE boyhood I have had a keen interest in mining engineering. To see the prospector with his pack outfit and his pan, followed by the assayer and the trained engineer, has always had -something of the lure of romance for me. It is appropriate that the American Institute of Mining and Metallurgical Engineers should hold a general meeting in California, since this State has long been a home of mining engineering. Here, after the early open methods of mining, it has been necessary for the universities to train men in geology and mining, so that the earth could be penetrated and the rich ledges opened. In the eighty years in which the mines of California have been offering experience to the miners of the world, we have seen mining engineering evolve from a comparatively simple art, covered largely by rule of thumb, into a complex group of specialties, each utilizing the very latest discoveries in the various fields of physical sciences. Mining, too, has become a great business requiring large financial support and the most careful handling. Those mining engineers who have applied new processes in special fields have thus been able to give a wide-flung range to their activities in all parts of the world. The hand of nature in distributing minerals over the surface of the earth has compelled the mining engineer to become a modern pioneer, facing the heat of the tropics as well as the frozen regions of the north. There has been a marked cosmopolitan aspect to mining engineering, since the engineer had to go wherever the prospector discovered favorable leads. This has meant dealing with the harshest of conditions, the handling of labor of all sorts, the control of sanitary conditions, and relations to all forms of transportation. Naturally this has called on some of the very best minds in all countries to unlock the stores of hidden wealth. To make them available for civilization has been the job of the mining engineer.

Jan 1, 1929

By Jay A. Carpenter

WAR?S impact on Nevada mining and rnetallugrcal operations has brought about a rapid rise in the gross value of the ores mined and milled for the atratezic metals, and a sharp decrease in that for the precious metals. The State?s total production over the present war years will averaged out 10 per cent above the good record of $39,000,000 in 1937. However. this annual production is low in contract to that of nearly $47,000,000 in 1877 in the days of the great bonanza on the Comstock, and that of nearly $49,000.000 in 1918 during the last World War..

Jan 1, 1944

By R. R. Sayers

TWO serious hazards from coal dust confront the bituminous-coal miner- -a physical or safety hazard and a physiological or health hazard. The first threatens the miner with loss of life from coal-dint explosions, and the second with loss of health and earning capacity from inhaling large quantities of the dust. Studies by the Bureau of Mines have shown that coal dust, except some grades of anthracite dust, is capable of initiating an explosion when no explosive gas is present and that its property of extending or propagating an explosion has been responsible for nearly all the widespread explosions that have occurred in bituminous mines in the United States in the present century. For years many mining people believed that low-volatile coal dust was not explosive but not only is it explosive but if the source of ignition is intense, it is as explosive as the dust of many high-volatile coals because the war is creating increased pressure for greater coal production and because of the trend toward greater mechanization in mines, explosion and health hazards from coal dust are likely !n increase considerably.

Jan 1, 1943

By T. B. Counselman

WHEN one thinks of Minnesota iron ore, one thinks of big open pits, where high- grade ore is simply scooped up with a power shovel, loaded into cars, and hauled away for shipment to the blast furnace. On the western end of the Mesabi range, however, are large tonnages of iron ore which contain too much silica to be used directly in the blast furnace, and these ores must first be concentrated to a purer form. The Mesabi range is about 100 miles long and a maximum of 3 miles wide. The iron formation, which in its unaltered form is called taconite: consists of a banded iron- bearing chert. Where the high-grade ore bodies occur, these have resulted from folding and cracking with sub- sequent leaching out of the silica, leaving the iron oxide behind. The big open pits and the underground mines are situated in these concentrations.

Jan 1, 1941

By H. W. Morse

INTRODUCTION THE experimental work on the oxidized copper ore at the New Cornelia mine at Ajo, Ariz., ended on Jan. 12, 1916. On that date final decision was made on the general nature of the process to be used in the 5,000-ton leaching plant, and on many of the details, as far as experience on a40-ton scale could decide them. With the approval of the Board of Directors and the General Manager, John C. Greenway, we have compiled what seem to be the most interesting data on the results obtained during the experimental period. The most important part of the data resulted from the operation of a 1-ton and a 40-ton plant at Ajo. Experimental work on Cornelia oxidized ore dates back to April, 1912, and has been going on nearly continuously since that time. A good many variations from the original idea have been tried, but the process finally decided upon is in principle and in all of its details a simple one. The history of the leaching work on this ore has been brought down to about a year ago in papers presented to this Institute by Stuart Croasdale1 and Dr. L. D. Ricketts.2 The present paper will, therefore, deal principally with the results obtained during the last year of the work.

Jan 9, 1916

By Carl F. Floe, Michael B. Bever

TRE solubility of hydrogen in molten copper-tin alloys is of both practical and theoretical interest. From a practical standpoint, data on the equilibrium solubility as a function of temperature, pressure and alloy composition are valuable for a better understanding of porosity problems in bronze castings. From the theoretical point of view the determination of the hydrogen-copper-tin equilibrium is of interest since it extends the laws governing the solution of gases in metals. This paper presents the results of an investigation of the solubility of hydrogen in representative compositions of the copper-tin system at temperatures ranging from above the liquidus to 1300°C. and at pressures from less than 50 mm. of mercury to about atmospheric. REVIEW OF PREVIOUS WORK The solubility of hydrogen in copper was determined by Sieverts and Krumbhaarl in 1910 and by Roentgen and Moeller2 in 1934. Their values are in fair agreement. In 1926 Iwasé3 reported results that were very much higher. The published data on the solubility of hydrogen in tin do not agree. Smithells4 states that no reliable data are available. According to Sieverts and Krumbhaar,5 hydrogen is insoluble in tin. Bircumshaw,6 on the other hand, found a definite solubility at 800°C. The latter's experimental procedure did not provide for stirring of the metal and in his opinion he failed to reach equilibrium. Iwasé3 again reported large solubility values. For copper alloys, Sieverts and Krumbhaar6 distinguished between alloying elements that do not markedly affect the solubility of hydrogen, elements that increase the solubility, and elements that reduce it. They named gold, tin, and aluminum as examples of this last group and reported hydrogen solubility data at 1225°C. for the copper-rich side of these alloy systems at atmospheric pressure. Without giving experimental results, they stated that the amount of hydrogen dissolved by liquid copper alloys is proportional to the square root of the pressure as in pure metals. These authors suggested that in a limited way the effect of an alloying element on the solubility of a gas is related to the constitution diagram for the alloy system. Sieverts7 also called attention to the fact that the curve of hydrogen solubility versus composition of copper-tin alloys shows a sharp change of direction at the composition of Cu3Sn and suggested that this compound persists at least to some extent in the molten state. Iwas3é reported large hydrogen solubility values for several compositions of copper- tin alloys, which appear to be in error.

Jan 1, 1944

By J. E. Norton

Production statistics show that during the period of emergence from the depression the coal industry was becoming increasingly cognizant of the economic and competitive necessity for mechanizing. About 1935 many of its leaders were becoming aware also of the alarming scarcity of men properly trained to cope with the new problems of mechanization. In order to get a factual statement of this problem, a special AIME Coal Division Committee was requested to survey the condition. Its investigation disclosed that graduates of mining schools going into coal mining numbered 16 in 1937 and 15 in 1938. With this as a background, Pittsburgh Coal Co. foresaw that a comprehensive program was necessary if it was to enlist the services of trained technical men, who were an indispensable part of a mechanization program. The purpose of this paper is to review the program set up, to comment on the successes and failures and to outline the future course of action. Summer Work An inescapable conclusion from the mechanization statistics was that the opportunities in coal mining were good. Not only was there a void in technical skill to fill from past years, but the accelerating rate of mechanization indicated an increasing demand for technically trained men for the future. The remedy lay primarily in presenting facts con cerning the coal industry to the undergraduate engineers before they made their professional occupational choice. Based on this idea, one of the key points in the program was summer vacation work for the undergraduate, which, through the inducement of summer earnings, brought men into the mines to take a look at the prospects. This was more successful than statistics indicate because the war scrambled badly the orderly working of the program, but it could not obscure the value of a summer work program. A decided advantage was that it gave the company a preview of the graduate. An observation on this part of the program is that it is extremely hard to gauge lower classmen, and we found it wise to give them the benefit of the doubt, as the last two years in college bring about surprisingly rapid development in some men. We could readily single out the men at the opposite ends of the scale of competence. Comprehensive Training Program Having adopted summer work as a means of interesting undergraduates, the Location Weeks Introduction............................... I Underground mining operations............... 27 Coal preparation............................ 24 Inspection—safety, mech., prep............... 31 Mine engineering and survey................. 16 Industrial relations.......................... 12 Operating staff—costs, time study............. 8 Miscellaneous............................... I Total.................................... 120 problem of attracting graduates was met by establishing a training program that covered approximately 120 weeks and

Jan 1, 1949

By R. G. Clay, C. F. Seaman

THE mines of The Tennessee Copper Co. are in the Ducktown Basin, in southeastern Tennessee. The ore is a heavy sulphide consisting principally of chalcopyrite, pyrite and pyrrhotite and in places running as high as 05 per cent sulphur and iron. Operating mines are the Burra Burra and Eureka. Development of the Boyd ore body was started in 1940. Late in 1939 the decision was made to change from fuse and cap to all electric blasting and at the same time electric cap lamps were installed to replace carbide. These changes were made to improve the safety and working conditions in the mines. Both the Bureau of Mines and explosives manufacturers recommended electric blasting as a safety measure. Until that time, electric blasting had been used only for shaft sinking and in places where it was absolutely essential for safety. Very few men had had experience in this type of blasting, as the places where it was required were those that also required direct supervision. It was necessary for the mining staff to work out methods, procedure, and equipment to he used. In this they were ably assisted by representatives of the explosives manufacturers. Many mistakes were made and it is the purpose of this paper to describe the original plan and installation, show the major difficulties encountered, the remedies applied, and present the practices now being followed. Comparison of costs of the two methods will also be discussed. About six months were required to make the change and eliminate fuse and cap blasting entirely. The first electric blasting stations were installed in November 1939 and the last fuse was taken underground in May 1940. A very unusual condition forced the use of fuse for a short time in one heading after May, but that will be discussed later. ORIGINAL EQUIPMENT AND INSTALLATION A power line is generally recommended as a source of current where permanent blasting stations are used. The plan worked out for electric blasting was to tap 220-volt alternating-current lines when they were available and use 250-volt direct current from the trolley wire at all other places. A blasting machine would he available at each shaft for places where there were no regular blasting stations and could he used if a regular station should fail. The equipment decided on was No. 16 duplex reinforced lamp cord for lines to within about 50 ft. of the working place and No. 20 lead wire from that point to the shots. An open double-pole, double-throw switch with slate base was put in the circuit, so connected that the down position would close the line to the shots and the up position would connect it to the line from the power contactor. This switch was located in the circuit as close to the blast as was safe (should the shots explode when it was placed in the shooting

Jan 1, 1942

By Gerald, Sherman

INCREASED production and con¬sumption of all metals, indicate the progress of industry toward that condition formerly thought to be normal. With no market limitations on silver and gold the two new precious-metal mines, the Silver Queen (now the Golden Queen), in southern California, and the Sunshine, at Kellogg in northern Idaho have made progress toward a high routine production. The Golden Queen 300-ton mill is finished and ready. The Sunshine mill has been enlarged and production is now at the rate of 500 tons per day of high-grade silver ore. The Hecla Mining Co. is developing the Polaris vein, which should be the extension of the Sunshine to the east. Some rich ore is reported. The developments of the' East African Gold Fields, Ltd., in the Lupa gold field of Tanganyika Territory, have made good progress, but operation in an isolated locality is not rapid and a large plant will be required. There have been no other discoveries reported that can be compared with the three mentioned, but production has increased, with greater capacity in dredging equipment and underground mines more adequately prepared for production.

Jan 1, 1936

By Cyril Wells, Robert F. Mehl

The two earlier papers in this series1,2 presented data on the rate of diffusion of carbon and of manganese in gamma iron. Apart from their scientific interest, these data are needed chiefly in order to treat data on carburization, on rate of formation of pearlite, and on rate of austenit-izing in a quantitative way.1'2'9'10 In the present investigation rates of diffusion of nickel in ?-Fe over wide temperature and concentration ranges have been determined, and the effects of carbon, of im- purities, and of grain size on these rates have been studied. Claussen,3 using the data of Fry,4 has calculated the diffusion coefficient of nickel in y-Fe as 9.2 X 10-11 sq. cm. per sec. at 1200ºC., but had no data from which to calculate the variation of D with concentration, temperature, and percentage of carbon. Method and Materials Method.—Nickel was diffused along the axis of a cylindrical specimen across a concentration gradient, concentration-penetration curves were determined and D values calculated from Grube or Matano solutions.5 Details of the method are given

Jan 1, 1941

By Cyril Wells, Robert F. Mehl

The two earlier papers in this series1,2 presented data on the rate of diffusion of carbon and of manganese in gamma iron. Apart from their scientific interest, these data are needed chiefly in order to treat data on carburization, on rate of formation of pearlite, and on rate of austenit-izing in a quantitative way.1'2'9'10 In the present investigation rates of diffusion of nickel in ?-Fe over wide temperature and concentration ranges have been determined, and the effects of carbon, of im- purities, and of grain size on these rates have been studied. Claussen,3 using the data of Fry,4 has calculated the diffusion coefficient of nickel in y-Fe as 9.2 X 10-11 sq. cm. per sec. at 1200ºC., but had no data from which to calculate the variation of D with concentration, temperature, and percentage of carbon. Method and Materials Method.—Nickel was diffused along the axis of a cylindrical specimen across a concentration gradient, concentration-penetration curves were determined and D values calculated from Grube or Matano solutions.5 Details of the method are given

Jan 1, 1941

By John C. Calhoun, Frank T. Bethel

Glass beads have been surface treated with Dri-film to render them oil wet by n-octane to varying degrees, and capillary desaturation curves have been determined by the restored state method. The desaturation curves show a regularity of increasing displacement pressures as the oil wetness increases. This has been used to compute apparent contact angles between n-octane and water on glass. The family of desaturation curves also shows a regular crossover, such that the residual wetting liquid saturation values are in reverse order to the displacement pressures. A semi-logarithmic variation is shown between the apparent contact angle and the residual saturation. The desaturation data are interpreted to mean that the wetting liquid ceases to be a continuous phase within individual pores before the capillary pressure can be raised sufficiently to force out the wetting phase completely. The saturation of wetting liquid at which this break in liquid continuity occurs is higher as the oil wetness decreases. INTRODUCTION The petroleum industry has for some time been using measurements of capillary pressures on porous media for research correlations and engineering calculations. It has been generally recognized that the capillary desaturation curve reflects the character and arrangement of the pores within the media and the distribution of fluids within the pores. Methods have been proposed for computing pore size distributions, tortuosity factors. and relative permeabilities from capillary desaturation data.' There is little doubt that the interactions between porous rocks and their contained fluids resulting from surface forces play a dominant role in determining the magnitude and direction of capillary pressure measurements. There have been attempts to introduce as variables two quantities — inter-facial tension and contact angle — generally used to char- acterize surface forces, but in spile of the wide interest in these quantities as important variables, few definite conclusions have been drawn concerning their qualitative or quantitative significance. INTERFACIAL TENSION The interfacial tension appears in a capillary pressure function given by Leverett for correlating capillary desaturation type curves. Use of the interfacial tension in this function seems to be justified by other experiments reported. Apparently, interfacial tensions have little bearing on wetting phase residual by desaturation. CONTACT ANGLE The contact angle was utilized as a variable by Bartell and co-workers"." in tests on displacement pressures, later recognized as the initial point of capillary desaturation. Although Leverett did not include contact angle in his original formulation of the capillary pressure function, later workers suggested its addition. Few reports are available to show variation of residual liquid with contact angle as a result of capillary desaturation.' The problems attendant to measuring contact angle within a porous medium are great. As a consequence of the lack of a concrete approach to a measurement. the workers in this area of research have adopted the general expression of "wettability" to indicate the relative position of two liquids saturating a porous body. It has been shown that gross measurements on porous systems, including capillary desatura-tions, are sensitive to wettability. Attempts at giving a scale to wettability in terms of contact angle through capillary desaturation curves have been made and these apparently are steps in the right direction. In these attempts presence of many other variables precludes attainment of exactness. Also, as a result of other variables, it has been impossible to correlate changes in apparent contact angle with changes in other physical measurements of the systems in question. The present work is an attempt to eliminate as many variables as possible in measuring capillary desaturations resulting from changes in contact angle within a porous medium.

Jan 1, 1953

By Harry J. Evans

DURING the fury of the conflict it was believed quite generally that World War II was being fought for and would accomplish a permanent peace. Yet, before the guns were actually stilled on all fronts, the American people realized that the devastated world would continue to be dominated by suspicion and uncertainty. The misunderstandings which rapidly developed indicated that it may prove unwise to rely wholly on mutual international agreements and contracts to avoid war. Before the celebrations of V-Day died down serious thought was being given toward measures for preparedness for the next conflict. Along with a realization of the enormous loss of life caused by the destructive forces of war, the American people came to understand the seriousness of the rapid and unwarranted depletion of our natural resources. During the last half of 1945 the question of stock-piling strategic and critical raw materials for a future national emergency became an intensely live subject.

Jan 1, 1946

By Cyril Wells, Robert F. Mehl

THE two earlier papers in this series1,2 presented data on the rate of diffusion of carbon and of manganese in gamma iron. Apart from their scientific interest, these [] data are needed chiefly in order to treat data on carburization, on the rate of formation of pearlite, and on the rate of austenizing in a quantitative way. 1,2,9,10 In the present investigation rates of diffusion of nickel in -?-Fe over wide temperature and concentration ranges have been determined, and the effects of carbon, of impurities, and of grain size on these rates have been studied. Claussen,3 using the data of Fry,4 has calculated the diffusion coefficient of nickel [ ] in -?-Fe as 9.2 X 10-11 sq. cm. per sec. at 1200T., but had no data from which to calculate the variation of D with concentration, temperature, and percentage of carbon. METHOD AND MATERIALS Method.-Nickel was diffused along the axis of a cylindrical specimen across a concentration gradient, concentration-penetration curves were determined and D values calculated from Grube or Matano solutions.5 Details of the method are given

Jan 1, 1941

By F. V. Tideswell

THE suggestion, which appears to find increasing favor, that the elementary composition of coals should be used as the basis of their classification, makes it important that our methods of expressing this elementary composition should be refined. It is doubtful whether many published ultimate analyses of coals are accurate within 1 per cent. carbon. Many are probably as much as 3 or 2 per cent. in error in carbon. It is, perhaps, not always realized that the extreme variation in carbon content over the range of bituminous coals is but 16 per cent. An error of 1 per cent. in carbon on analysis corresponds therefore with one-sixteenth of the whole range, an amount which is unjustifiable even for the application to commercial needs of a system of classification based on ultimate analysis. For the purposes of scientific research such limited accuracy is of little value. The object of this paper is to examine one important source of error in ultimate analysis, that due to the occurrence in coal of inorganic material, and to emphasize the need for the quantitative measurements (of carbon more particularly) on coals to be rendered independent of their contents of such material.

Jan 1, 1928

By T. V. Subrahmanyam, A. P. Rao

The adsorption behavior of chalcopyrite has been studied at different xanthate concentrations and flow rates in a column apparatus with potassium ethyl xanthate as the collector. Based upon the experiment results an equation of the type: 1/F = K3 + m3C + k2/t.Cm2.fm1 is proposed to account for the experimental data. Among copper minerals an early study on chalcocite by Gaudin and Schuman (Taggart, 1951) is well known for its research on the kinetics of the reaction by conventional method of mass balance between the products of reaction and xanthate consumed. The results were interpreted by the concept of ion exchange adsorption. Szeglowski (1977) conducted measurements on the adsorption of potassium ethyl xanthate on copper polarized to various potentials, the adsorption being measured by radio-tracer techniques. The adsorption in the range -1800 to 700 mv was found to be a reversible physical adsorption. The potential range in which the primary electrode process could lead to surface coverage with a minimum number of product layers was evaluated. The adsorption density of xanthate on sulfide surface was found to be related to the concentration of xanthate in solution and concentration of depressants as: [ ]

Jan 1, 1983

By Louis A. Panek

INTRODUCTION AND SUMMARY With respect to the geomechanics aspects, the primary technical objectives in mining by an undercut-cave method are to achieve a controlled, sustained caving of the mineral body and to remove the fragmented ore with a minimum of dilution from surrounding unmineralized rock, while maintaining stability or control of the rock structure around the access openings. The structurally ideal ore body probably does not exist. If the rock mass is so weak as to cave on a short span, it may tend to be too sticky for easy drawing and handling, or create special problems in regard to support of the access openings. If the ore is strong, caving may be difficult and the caved fragments may be of such a large size as to require special equipment for transferring the ore from the caved zone. Given enough time and money to generate data and conduct trials, engineering and ingenuity can devise an appropriate combination of mine layout, sequence of extraction, and mechanical equipment to achieve a technically successful caving extraction operation to meet the foregoing requirements in many types of deposits. The large capital investment involved, however, reduces the freedom to make major changes once the mine development is well under- way, and the penalties for failure to accurately anticipate operating conditions militate against selecting any but the most obvious candidates for mining by an undercut-cave method. The demonstrated capability to extract large, deep, economically marginal deposits by this low-cost, high-volume method of mining provides an incentive to develop a rationale for predicting the cavability and stability characteristics of a deposit prior to mining, so that the undercut-cave method may be extended to a much wider range of mineral deposit characteristics. The ultimate goal is to establish as explicitly as possible the quantitative interrelationships between the measured rock-mass characteristics, the caving span, the size distribution of caved ore fragments, and the sizes and locations of stable access openings. Lacking an understanding of these relation- ships, a designer may readily change some factor in the wrong direction (e.g., excessively reduce the distance between the extraction level and the undercut to increase the convenience of operations for the undercutting crew, increasing the frequency of repairs to the extraction-level support system) or create unnecessary problems elsewhere in the system by introducing a design change that can achieve only minimal improvement in the factor of direct interest (e.g., unnecessarily complicate the ore-transfer system by changing the orientations of the openings, with- out succeeding in the objective of improving the ground support conditions). Although successful predesign is the prime objective, subsequent modifications in mine lay- out and sequence of extraction operations are inevitable. In developing the modified solution, systematic experimentation based on an understanding of the underlying structural relationships, coupled with monitoring measurements of selected diagnostic structural-behavior parameters, can achieve an acceptable solution in a minimum number of steps, which is far superior to the typical operational trial-and-error approach, in view of the cost of implementing each successive change. Since a drill-core sample of ore rock from a successful undercut-cave operation may exhibit a uniaxial crushing strength in excess of 100 MPa, the caving of such a rock mass is now commonly believed to be ascribable to the presence of discontinuities such as joints or fractures throughout the ore body. An essential part of the present investigation was therefore to characterize the natural discontinuities at each of the test sites by measuring their attitudes and spacings. The term "fracture" is used herein in a general sense to include any planar discontinuity without implication as to its suggested mode of origin. Most, but not all, of the fractures are properly termed joints. As a point of departure we may consider the possibility that the rock mass is transected by three families of joints, each family possessing a distinct orientation, such that parallelepipeds of intact rock are delineated by the jointing. Even if cementation is absent between adjoining parallelepipeds, the undercutting of the rock mass will not necessarily initiate sustained caving--owing to the all-around confinement, an arch may tend to stabilize over the undercut unless prevented from doing so by the failures of key blocks of intact rock. Thus, although the jointing can be assumed to weaken the rock mass, creating preferred directions of

Jan 1, 1981