Search Documents

By J. Blodget Britton

SIX different samples of anthracite, each a firm compact lump, were finely pulverized and immediately put in bottles. Portions of these were weighed and placed upon an ordinary water-bath and dried for one hour; the average loss was 1.24. The same portions were then placed in a hot-air oven, and for two hours kept at a temperature of 285' F., and, after cooling in a dry chamber, were again weighed, when there was found a further average loss of 1.22, making a total so far of 2.46. They were then immediately returned to the oven and for two hours more kept at a temperature of 530' F. and cooled and weighed again, when no further loss was found, but an average gain of .55 upon the previous weighing. The same portions were a third time placed in the oven and for about ten minutes kept at the last-mentioned temperature, and then, while still hot, were poured into one-quarter inch glass tubes, each with a bulb at one end, and heated over a Bunsen burner at a temperature below a red heat, when more water vaporized and condensed in small clear globules on the cold parts of the tubes. Fresh portions of the coals were then taken, and the total amount of water determined, and the average was found to be 3.04, or 1.80 more than was found at the temperature of the water-bath, which was perhaps a little below 212' F., and .58 more than at 285' F. Tests were afterwards made by placing other fresh portions of the

R. B. BRINSMADE, Puebla, Puebla, Mexico (communication to the Secretary*) :-As I have previously considered the general equations for mine-valuation,1 I will here discuss only that part of Mr. Finlay's paper criticized by E. E. White, along with some of the general principles of mining taxation, under the following six topics: 1. Rate of interest earned by sinking-fund. 2. Rate of interest earned by investment. 3. Place of royalty item in valuation. 4. Place of taxation item in valuation. 5. Calculation of future ore-prices. 6. Valuation of undeveloped mining land. 1. Rate of Interest Earned by Sinking-Fund.-Mr. Denny's quoted opinion of a 3 per cent. rate is evidently based on English conditions before the Boer war. The great destruction of liquid capital by the great wars and catastrophes since 1897, along with the flood of gold and consequent rise in the average index of commodity prices, has undoubtedly increased the rate of interest at least one-half per cent. In the United States sound savings banks now allow 4 per cent. on deposits, while safe bonds are quoted at prices which yield even 5 per cent.. 2. Rate of interest Earned by Investment.-Gold-mines with uncertain and scanty ore reserves, the objects of Mr. Denny's quoted remarks, are quite different from iron,. copper, or coal mines with definite mineral reserves blocked out ahead by drilling or driving. While 10 per cent is often all inadequate yield from gold-mines, the latter class of mines are often, as safe as city real estate and resemble it as an investment in more ways than one.

Jan 10, 1913

By Ralph Arnold

THE American oil 'industry has reached the critical stage where the demand exceeds the supply with no hope of permanently bettering the situation through the development of new fields in the United States. Remedies may be sought along three lines: 1. Securing a foreign source of supply. 2. Curtailment of the use of oil and its derivatives. 3. Improvement in methods of recovery (including the recovery of shale oil), refining, and utilization. The oil companies with proper government support will push the acquiring of foreign territory; the price of oil and oil products will enforce a curtailment in use; it remains for the producers and refiners to brings about improvements and economy in recovery, transportation and refining; the general public must be instructed in utilization. The solution of the problem, therefore, rests largely in the hands of the technologists of the industry -the drillers, engineers, geologists, chemists, etc. Only through an exchange of the ideas of the individuals who are conducting the industry will its technology be advanced. , Among the agencies at work to bring about this result are the United States Bureau of Mines, the American Petroleum Institute, and the A. I. M. E. The Bureau of Mines has a trained staff of experts, maintains experiment stations and a field force of technologists, and issues many technical papers helpful to the industry. The Petroleum Institute is a clearing house for useful statistics and is now. organizing a research division under the able direction of Doctor Manning, but its principal field of activities is in the realm of co¬ordinating ?the financial and commercial activities of the` oil' companies.' It remains for the American Institute of Mining and Metallurgical Engineers to organize the individual technologists of the industry and provide them with means of exchanging and disseminating ideas through meetings and publications. It is the aim of the Petroleum Committee of the American Institute of Mining and Metallurgical Engineers to foster this exchange of ideas among oil men by enlarging the membership of the Institute among the field and office technical forces of the oil companies and thus arouse their interest in the vital problems of the oil business.

Jan 1, 1920

By ALFRED KAUFFMAN

NO matter what position we hold, workman, foreman, superintendent, manager, president, or what not, let us fail to give or to make good products, then see how quickly we'll be called to account for- our work by the buying public. The waves of progress taught us that millions were wasted in unnecessary strikes-we also learned that many losses were due to neglect on the part of manufacturers to give the same consideration and attention to the human element of their factory as they gave to their machinery. The employees learned also that the employer was their agent who found purchasers for the product of their labor. So between the two we learned that many years of labor were needed in order for a worker to recover his wasted savings, or for the manu¬facturer to replenish his loss. Treat 'em rough, and tell 'em nothing, was not very far from the true relationship between management and employees in manufacturing plants in the early days. Today just exactly the opposite views are held by executives whose function is the handling of employees. Men today want to know what it is all about. They are intelligent enough to comprehend the facts, and to use them constructively, and it is good business to give them the information.

Jan 1, 1929

By J. Blodget Britton

Six different samples of anthracite, each a firm compact lump, were finely pulverized and immediately put in bottles. Portions of these were weighed and placed upon an ordinary water-bath and dried for one hour; the average loss was 1.24. The same portions were then placed in a hot-air oven, and for two hours kept at a temperature of 285° F., and, after cooling in a dry chamber, were again weighed, when there was found a further average loss of 1.22, making a total so far of 2.46. They were then immediately returned to the oven and for two hours more kept at a temperature of 530° F. and cooled and weighed again, when no further loss was found, but an average gain of .55 upon the previous weighing. The same portions were a third time placed in the oven and for about ten minutes kept at the last-mentioned temperature, and then, while still hot, were poured into one-quarter inch glass tubes, each with a bulb at one end, and heated over a Bunsen burner at a temperature below a red heat, when more water vaporized and condensed in small clear globules on the cold parts of the tubes. Fresh portions of the coals were then taken, and the total amount of water determined, and the average was found to be 3.04, or 1.80 more than was found at the temperature of the water-bath, which was perhaps a little below 212° F., and .58 more than at 285° F. Tests were afterwards made by placing other fresh portions of the

Jan 1, 1877

By Eugene Guccione

"All engineering societies should encourage and motivate their members to take part in public affairs. And engineers, in turn, should learn to translate their technical knowledge in a language which politicians can understand," stated James Boyd last month as he received the Hoover Medal, which is awarded annually by four engineering societies-AIME, IEEE, ASME, and ASCE-to an engineer who has rendered important public service. James Boyd is no ordinary engineer (see box). A few weeks ago, Dr. Boyd took time out of his busy schedule to stop at MINING ENGINEERING'S editorial office for the following exclusive interview.

Jan 1, 1976

By Ralph H. Sweetser

At the joint session of Blast Furnace and Open Hearth Committees, April 7, 1937, at Birmingham, the subject of the quality of basic open-hearth pig iron was so well presented and discussed from so many different viewpoints that it was the general opinion that progress had been made and that such meetings were conducive to the advancement of the art of making pig iron of the right quality for the open-hearth man to produce the most satisfactory quality of steel. It was agreed that there is a decided differentiation between the chemical analysis of pig iron and the "quality" of pig iron. Paul J. McKim said that open-hearth furnace operators frequently make reference to certain types of iron as "bad iron," "dirty iron," "cold metal," etc., claiming that when using these irons, although they are within specified chemical analysis, it is impossible to produce quality steel. Mr. McKim gave a list of the suggested causes of those "certain types" of bad irons that have a thoroughly respectable analysis but a thoroughly disreputable character. Another open-hearth man, P. A. MacIsaac, of Nova Scotia, said that: The effects of iron that is below standard in analysis or in that mysterious property called quality, are well known to all open-hearth operators. It has been shown that iron of this type results in the production of steels on which the rcjections of finished product run high. What is to be done about it? I would say that the burden of producing high-quality iron should be placed squarely on the shoulders of the blastfurnace man, even as that of making good steel is shouldered by the open-hearth man. It is the purpose of this paper to bring out into the open this "mysterious property called quality"; that is, in those "certain types" of basic pig iron that make it impossible to produce quality steels; and at the same time to point the way for the blast-furnace man to be able to shoulder the burden that Mr. MacIsaac and all other open-hearth men and foundry-men have placed upon him. Silicon, sulphur, phosphorus and manganese are not the guilty elements because these are known, specified and usually kept within the

Jan 1, 1938

By Ralph H. Sweetser

At the joint session of Blast Furnace and Open Hearth Committees, April 7, 1937, at Birmingham, the subject of the quality of basic open-hearth pig iron was so well presented and discussed from so many different viewpoints that it was the general opinion that progress had been made and that such meetings were conducive to the advancement of the art of making pig iron of the right quality for the open-hearth man to produce the most satisfactory quality of steel. It was agreed that there is a decided differentiation between the chemical analysis of pig iron and the "quality" of pig iron. Paul J. McKim said that open-hearth furnace operators frequently make reference to certain types of iron as "bad iron," "dirty iron," "cold metal," etc., claiming that when using these irons, although they are within specified chemical analysis, it is impossible to produce quality steel. Mr. McKim gave a list of the suggested causes of those "certain types" of bad irons that have a thoroughly respectable analysis but a thoroughly disreputable character. Another open-hearth man, P. A. MacIsaac, of Nova Scotia, said that: The effects of iron that is below standard in analysis or in that mysterious property called quality, are well known to all open-hearth operators. It has been shown that iron of this type results in the production of steels on which the rcjections of finished product run high. What is to be done about it? I would say that the burden of producing high-quality iron should be placed squarely on the shoulders of the blastfurnace man, even as that of making good steel is shouldered by the open-hearth man. It is the purpose of this paper to bring out into the open this "mysterious property called quality"; that is, in those "certain types" of basic pig iron that make it impossible to produce quality steels; and at the same time to point the way for the blast-furnace man to be able to shoulder the burden that Mr. MacIsaac and all other open-hearth men and foundry-men have placed upon him. Silicon, sulphur, phosphorus and manganese are not the guilty elements because these are known, specified and usually kept within the

Jan 1, 1938

By F. P. Donohue

The observations and data presented in this paper are the result of extensive study of flowing wells, most of which were in the Maracaibo Lake Basin of Venezuela. The Lago Petroleum Corpn. had extensive production in this area, gas-oil ratios were low, and the problem was to determine whether by careful handling of the wells with respect to flowing conditions and by conserving the gas, the oil production of the wells could be maintained by natural flow until it had declined to a rate which could be handled with an ordinary working barrel, thereby avoiding the high cost of gas-lift equipment installation in the lake bed. The problem was complicated by the nature of the wells themselves. Production is from soft, comparatively unconsolidated sands, necessitating screen pipe in all wells. It was not only necessary to keep the wells flowing but to keep them flowing without heading, as the release of pressure upon making a head brought large quantities of sand into the wells, sanding them up or possibly cutting out the screen pipe. In furtherance of the plan of keeping wells flowing as long as possible, each well was equipped with a casinghead and tubinghead recording pressure gage, and an oil and gas separator set. About one-half of the wells were equipped with gas meters. All wells were tubed before bringing into production. Frequently individual gages were taken on each well. A large scale chart was plotted for each well, showing daily oil production, gas production, gas-oil ratio, tubinghead pressure and casinghead pressure. Any deviation from the normal was immediately checked and the condition remedied if possible. Theory of Flowing Wells Based upon considerable study of these records, it is believed that the flow of a well actuated by gas is mainly a problem in velocity, a certain minimum velocity in the flow string being necessary for the gas to carry the oil. If this minimum velocity is not obtained the oil drops back and the well heads or goes dead. The point of minimum velocity is of course at the bottom of the tubing, where the gas is under the highest pressure and therefore occupies the least volume. Some years ago when the success of the gas-lift at Seminole was so pronounced, there was considerable broadcasting of the statement that

Jan 1, 1930

SINCE I have mentioned the art of alchemy in. many parts of this treatise of mine, especially when 'came to the description of the practice of various operations,* I do not here intend to argue as to whether it may be called true or not. But in case it is true, inasmuch as it is seen in operation to be a result dependent on the actions and virtues of fires, I should not pass by in silence without speaking at all of this art here, nor would I wish to do so, especially since I think that you do not really know what it is except in so far as common report is heard everywhere to the effect that whoever carries it to completion makes silver and gold with it. Because of this belief, many seek it with much time, labor, and expense, as I know you have often heard related, if not elsewhere, by me in the chapter on gold that I have written in this volume. Now do not think that I wish to teach you this art here, for I am one of those who do not know it. Therefore I shall tell you here, so that you may know more, only. that those workers who so eagerly follow after and seek it proceed by just two pathways. One is that which takes its enlightenment from the words of the wise philosophers, by means of which they think to attain it. This they call the just, holy, and good way, and they, say that in this they are but imitators and assistants of Nature, indeed, manipulators and true physicians-of .mineral bodies, purging them of superfluities and assisting them by augmenting their virtue and freeing them from their defects. In this way they sometimes proceed to corrupt these bodies in order to be able to separate the elements they contain so as to reduce them, if possible, to their primary materials, as they call them, or sometimes they convert them into new substances by means of this art or by adding another spirit different from the first one. Thus they seek in this way to bring these materials to a certain point of corruption or to a separation of elements, or to remove or add spirits to things, or to make coarse materials subtle and sometimes to make subtle materials coarse. Therefore, as you can understand, these persons, with bridle broken, run a circular track night and day, without ever having rest; and surely I do not know whether anyone has ever arrived at the desired goal. Nevertheless, even though the goal of this art were emptiness, as many

Jan 1, 1942

By J. W. Spretnak, G. W. Cunningham

A study has been made of the growth and disappearance of voids in the interface of pressure bonded copper. The formation of visible voids is primarily due to spheroidization and coalesence of microvoids produced during the application of pressure. The microvoids could be prevented from forming by the application of high pressures or by increasing the ductility of the copper. Migrating grain boundaries were found to be more effective in void removal, than stationary grain boundaries. DURING the course of an investigation on the mechanism of pressure bonding, it was found that voids formed in the bonding interface which inhibited migration of the interfacial boundary and grain boundaries in the bond region. Therefore, an effort was made to determine the nature of the voids and how they form, grow, and disappear. This paper reports the results of such an investigation. The existence of interfacial voids is not solely a characteristic of massive components of metal which have been bonded by the application of heat and pressure, but is a phenomenon which has been observed in sintering as well. Simonsen attempted to study the sintering process by hot-stage microscopy and thereupon observed the formation of interparticle porosity as sintering proceeded. It was assumed that the porosity was due to grooves created at the location where grain boundaries joined the surface of the particle. Pranatis, Castelman, and seigle2 have also observed voids along the areas of contact in wound-wire specimens used for sintering studies. They did not discuss the point in detail since this behavior was not general, but they did suggest that the voids might develop as a result of stresses along the interparticle contact area. In previous investigations on pressure bonding, workers3 have suggested that voids may exist in the region where mating surfaces are placed in intimate contact, but the existence of the voids was not verified and no attempt was made to study the growth and disappearance of these voids. Durst noted the existence of pores in roll-clad structures prepared by cold reducing two sheets to force them in contact and then annealing to improve the bond. Since his unbonded regions contained a gas which he assumed to be insoluble, he proposed a mechanism which consisted of spheroidization of the unbonded regions and a growth of the contact area, but no speculations were made regarding disappearance of the gas filled pores. One interesting comment made by Durst was the suggestion that flattened voids with sharp corners which are produced during roll bonding will have a greater driving force for spheroidization than the more rounded pores created by pressing metal powders and thus spheroidization and neck growth will occur at lower temperatures. In this study it was necessary to demonstrate conclusively that voids can actually exist in the interfacial bond area. Experimental work was then directed toward a study of the mechanism whereby the voids grow and subsequently disappear.

Jan 1, 1963

By R. S. Busk, E. G. Bobalek

The relation between gases and metals has been a subject of increasingly active investigation during the past years, principally devoted to the study of metal-hydrogen systems. It has been found that hydrogen is soluble in most molten metals to an appreciable extent and somewhat soluble in most solid metals.l,2 In every known case there is a sudden decrease in solubility at the melting point. Thus a freezing mass of metal containing hydrogen in excess of the solid solubility must in some way expel that excess during the freezing process. This leads to internal blowholes, and such effects as pinhole porosity. Gas trapped in metal that is to be fabricated by a working process such as extrusion or rolling may be the cause of blisters. For some cases, notably in copper and iron alloys, the presence of hydrogen can lead to extreme embrittle-ment of the metal. The aluminum-casting industry has long recognized the importance of hydrogen in its techniques. Excess gas in molten aluminum alloys often leads to the formation of "pinhole porosity" in the solid casting.= To prevent this hydrogen pickup it is necessary to avoid overheating the melt and to protect it from such sources of hydrogen as water. In spite of all precautions, it is sometimes necessary to extract hydrogen from the melt just before pouring by bubbling with a gas such as chlorine or nitrogen. Reccntly it has been found that somewhat similar effects are possible with magnesium alloys, in that the presence of hydrogen can induce or aggravate micro-p~rosity.4-6 This paper is primarily concerned with a presentation of some facts concerning the solubility of hydrogen in magnesium and its alloys, with some discussion of the significance of these facts in a practical sense. In any study of gas-metal systems it is important to bear in mind a clear distinction between adsorption on surfaces and absorption within the lattice.' Considerable attention has been directed toward determining whether hydrogen is truly soluble in any solid metal, or whether the gas extracted from a sample was present at surfaces (external and internal) only.7 Most present day evidence supports the idea of true solution in addition to adsorption. A second important factor when dealing with gas solubility is the dependence of such solubility on external pressure. For diatomic gases such as H², solubility in both liquid and solid metals apparently is proportional to the square root of the pressure, indicating a breakdown to a monatomic gas before diffusion into the lattice.= For true equilibrium values of solubility, therefore, the pressure at the the surface must be constant and, preferably, known. Very little has been published concerning the hydrogen-magnesium system. Winterhager has presented the most

Jan 1, 1947

By R. S. Busk, E. G. Bobalek

The relation between gases and metals has been a subject of increasingly active investigation during the past years, principally devoted to the study of metal-hydrogen systems. It has been found that hydrogen is soluble in most molten metals to an appreciable extent and somewhat soluble in most solid metals.l,2 In every known case there is a sudden decrease in solubility at the melting point. Thus a freezing mass of metal containing hydrogen in excess of the solid solubility must in some way expel that excess during the freezing process. This leads to internal blowholes, and such effects as pinhole porosity. Gas trapped in metal that is to be fabricated by a working process such as extrusion or rolling may be the cause of blisters. For some cases, notably in copper and iron alloys, the presence of hydrogen can lead to extreme embrittle-ment of the metal. The aluminum-casting industry has long recognized the importance of hydrogen in its techniques. Excess gas in molten aluminum alloys often leads to the formation of "pinhole porosity" in the solid casting.= To prevent this hydrogen pickup it is necessary to avoid overheating the melt and to protect it from such sources of hydrogen as water. In spite of all precautions, it is sometimes necessary to extract hydrogen from the melt just before pouring by bubbling with a gas such as chlorine or nitrogen. Reccntly it has been found that somewhat similar effects are possible with magnesium alloys, in that the presence of hydrogen can induce or aggravate micro-p~rosity.4-6 This paper is primarily concerned with a presentation of some facts concerning the solubility of hydrogen in magnesium and its alloys, with some discussion of the significance of these facts in a practical sense. In any study of gas-metal systems it is important to bear in mind a clear distinction between adsorption on surfaces and absorption within the lattice.' Considerable attention has been directed toward determining whether hydrogen is truly soluble in any solid metal, or whether the gas extracted from a sample was present at surfaces (external and internal) only.7 Most present day evidence supports the idea of true solution in addition to adsorption. A second important factor when dealing with gas solubility is the dependence of such solubility on external pressure. For diatomic gases such as H², solubility in both liquid and solid metals apparently is proportional to the square root of the pressure, indicating a breakdown to a monatomic gas before diffusion into the lattice.= For true equilibrium values of solubility, therefore, the pressure at the the surface must be constant and, preferably, known. Very little has been published concerning the hydrogen-magnesium system. Winterhager has presented the most

Jan 1, 1947

By G. A. Moore

A brief review is given of methods designed to produce metallic iron of high purity, and typical results are listed. A recent method, utilized at the National Bureau of Standards, consists of the extraction of ferric chloride by ether, reduction of this ferric chloride to ferrous chloride, further purification of this chloride, and the subsequent electrolytic deposition of metallic iron. iron produced by this procedure apparently is softer than, and otherwise different in properties from, any iron previously prepared and contains appreciably smaller amounts of impurities. THE history of attempts to produce "pure" iron reaches to antiquity and it may be presumed that each ancient armorer who succeeded in making a better steel concluded, correctly, that he had done a better job of removing the "base metals," and incorrectly, that he now at last had a "pure" metal. Early metallurgical papers mentioned use of "pure iron" in making alloys—this "pure" iron in most cases being inferior to some commercial stocks of the present time. Improvement has been continuous, and usually at a sufficient rate to convince each succeeding group of workers that they, at last, were using the really pure metal (until the analysts also improved their techniques to again discover the impurities). These adventures were reviewed in some detail by Cleaves and Thompson.' Although the ores of a metal may be abundant, difficulties in extracting it may make the pure metal very rare. When impurities are restricted to a total of a few parts per million, nearly all pure metals become rarities. Lead, copper, gold, mercury, silver, zinc, aluminum, bismuth, and the six platinum metals are claimed to be available with total impurities ranging from 2 to 50 ppm. The present small and scattered world supply of so-called "pure" iron holds an unimpressive place in another group of 16 metals having approximately 100 ppm of foreign material. Of about 20 less rare metals, only the platinum metals are more costly to prepare. While the production of such rare varieties of iron may appear insignificant in the presence of thousand-ton operations with 95 to 99 pct metal, it must be emphasized that all researches on commercially interesting irons and steels are in fact studies of the modifications of the properties of iron by additional materials. Until the properties of high purity iron are directly measured, all ferrous research must operate without known base values. Traces of impurities may affect the properties of a metal in many ways. Infinitesimal traces of solutes, by disturbing the electronic configuration, greatly change the electrical properties of transistors and semiconductors2-3 and slightly larger traces might alter these quantities in iron. Soluble impurities which disturb the perfection of lattice arrangement not only may alter the magnetic constants and electric properties, but by their close association with dislocation phenomena probably control the very existence of the "yield point"; determine the value of yield stress; and perhaps control the selection of slip and cleavage planes. It has been speculated that impurities might even cause the allotropic transformation in iron, but in any case their rearrangement must contribute to the unreliability of heat capacity and other thermodynamic measurements. Impurities which do not remain in solution may cause even greater effects on the properties. Microscopically visible amounts of phases other than ferrite can be found in all high purity irons which have come to my attention. It can be calculated that from 50 to as little as 2 ppm of an insoluble material might be sufficient to completely film all grain boundaries in irons having grain sizes from ASTM Nos. 10 to 1. Should this occur, such films, even though invisible, may be very important in fracture problems, especially at extremes of temperature:' Studies of grain growth and diffusion normally imply consideration of a single-phase system, hence, in the presence of insoluble impurities they can be expected to give ambiguous data." High purity iron is also in demand for use as chemical and spectro-chemical standards; for work in classifying the lines of the iron spectrum; for biological work in nutrition; and for work in nuclear physics. where the presence of some sensitive

Jan 1, 1954

By R. B. Adamson

The fatigue behauior of irradiated copper single crystals is compared to that of unirradiated crystals. Proton or electron irradiation did not substantially change the fatigue-lzj.e, fatigue-hardening-, or slip-line characteristics, while neutron irradiation did appear to alter these parameters. Postfatigue transrrzission electron microscopy did not reveal any marked structural differazces between irradiated and unirradiated specimens. Possible dislocatio~a mechanisnzs to explain the observed behavior are discussed. A LTHOUGH considerable work has been done to ascertain the effects of radiation on the tensile properties of metals (e.g., Refs. 1 and 2), little work of a basic nature has been reported on the effect of radiation on fatigue properties. Since it is known that fatigue properties are sensitive to conditions at the surface of the metal, it was felt that charged particle irradiation, whose penetration into metals is very small, might influence the fatigue behavior. To investigate this surface effect, irradiations with 10 mev protons and 1.5 mev electrons were conducted. The range of 10 mev protons in copper is about 0.236 mm; which is very small compared with the thickness of the specimens used (1.53 mm). The range of 1.5 mev electrons is somewhat larger, on the order of 0.665 mm.4 On the other hand, irradiation with reactor neutrons produces damage throughout the entire specimen, so neutron irradiation can be used to study the effects of bulk damage. The damage introduced by proton and neutron irradiation is expected to con!ist of large interstitial dislocation loops,5 tiny (<25A) vacancy loops," and/or various vacancy-rich regions called depleted zones.&apos; In the case of electron irradiation at about -173°C the damage is expected to consist of isolated Frenkel pairs.&apos; The effect of radiation damage on the fatigue properties of some engineering materials has been reported,g,10 but the results are not clear-cut or consistent. SPECIMEN PREPARATION Zone-refined copper was used to grow single crystals by a modified Bridgeman technique in an inert helium atmosphere. Using a seeding method, single crystals were obtained as bars about 6 in. long with a cross section of 3 by $ in. Immediately upon removal from the split-mold graphite boat in which they were grown, the very soft bars were embedded in a room-temperature setting plastic. They could then be cut into specimen lengths without introducing any long-range damage. Generally, four or five specimens plus one seed were obtained from each bar. The plastic material was dissolved away in acetone and the orientation of each sample was checked by the standard Laue X-ray

Jan 1, 1968

Jan 1, 1882

By Jay R. Burns

TWO magnesium sand-casting alloys are commonly favored in the United States. These are referred to as H and C alloys (Dow Chemical Co.) or 4Mz65 and AM260 alloys (American Magnesium Corporation). Both are of an aluminum-zinc-manganese type. H alloy contains 6 per cent aluminum and 3 per cent zinc and is characterized by relatively good toughness. C alloy contains 9 per cent aluminum and 2 per cent zinc and is employed where high yield strength and pressure tightness are required. Examination of magnesium castings poured in Europe and England,&apos;J however, demonstrates that H and C alloys are replaced by .%8 and AZ~I, respectively. That is, A8 reprcsents a magnesiurn alloy having superior toughness while A291 is suitable for high yield strength and pressure-tight applications. The basic difference between the .Ameri-can and European alloys is that the foreign alloys employ a somewhat higher aluminum content and less zinc than is found in H and C alloys. The mechanical properties of the alloys, when divided into high and low-aluminum groups, are quite similar, as determined from separately cast foundry-control type test bars ,In this paper the decrease of mechanical properties caused by any given amount of microporosity is measured for H, C, A8, and AZ~I alloys. The relative susceptibility of each of the four alloys to microporosity is also determined. Typical mechanical properties and nominal chemical analyses are reported in Table I. The apparent similarities between the two alloys in each group have led to considerable discussion as to the relative merits of each of the compositions.2 Popular points for comparison between the alloys have been the relative susceptibility of each of the four alloys to microporosity6 and the effect of this microporosity on their mechanical properties. It is primarily intended, in this paper, to show the

Jan 1, 1946

By Jay R. Burns

TWO magnesium sand-casting alloys are commonly favored in the United States. These are referred to as H and C alloys (Dow Chemical Co.) or 4Mz65 and AM260 alloys (American Magnesium Corporation). Both are of an aluminum-zinc-manganese type. H alloy contains 6 per cent aluminum and 3 per cent zinc and is characterized by relatively good toughness. C alloy contains 9 per cent aluminum and 2 per cent zinc and is employed where high yield strength and pressure tightness are required. Examination of magnesium castings poured in Europe and England,&apos;J however, demonstrates that H and C alloys are replaced by .%8 and AZ~I, respectively. That is, A8 reprcsents a magnesiurn alloy having superior toughness while A291 is suitable for high yield strength and pressure-tight applications. The basic difference between the .Ameri-can and European alloys is that the foreign alloys employ a somewhat higher aluminum content and less zinc than is found in H and C alloys. The mechanical properties of the alloys, when divided into high and low-aluminum groups, are quite similar, as determined from separately cast foundry-control type test bars ,In this paper the decrease of mechanical properties caused by any given amount of microporosity is measured for H, C, A8, and AZ~I alloys. The relative susceptibility of each of the four alloys to microporosity is also determined. Typical mechanical properties and nominal chemical analyses are reported in Table I. The apparent similarities between the two alloys in each group have led to considerable discussion as to the relative merits of each of the compositions.2 Popular points for comparison between the alloys have been the relative susceptibility of each of the four alloys to microporosity6 and the effect of this microporosity on their mechanical properties. It is primarily intended, in this paper, to show the

Jan 1, 1946

By T. S. Lundy, R. E. Pawel, F. R. Winslow, C. J. McHargue

The volume-diffusion coefficients of Nb-95 and Ta-182 in niobium have been measured over the temperature range 878° to 2400°C. High-temperature specimens (T 21500°C) were sectioned by conventional lathe and grinding techniques while low-temperature specimens were sectioned by an anodizing and stripping technique previously described. Over a range of more than ten orders of magnitude in diffusivity, the self-diffusion data is well-represented by the equation: D = (1.1+ 0.2) exp [- (96,000 * 900)/RT ] cm2/sec Upward deviations from this line are explained by short-circuit diffusion in combination with the loss of resolution of the sectioning techniques. Oxygen contamination within the range 100 to 450 ppm was found to have little or no effect on the self-diffusivitj 01 niobium. In a limited number of measurements, the diffusivity of Ta-182 in niobium was found to be about half that of Nb-95 in niobium. These data may be described by D = (I.0+0.90.5)exp [- (99,300 * 2400) /RT ] PREVIOUSLY reported studies of self-diffusion in niobium were by Resnick and Castleman1 and Peart, Graham, and Tomlin.2 The data of Resnick and Castleman over a temperature range 1585" to 2120°C show considerable scatter but. can be represented by D = (12.4 *0.8) exp [-(105,000+3OOO)/RT] cm2/sec The limited data of Peart, Graham, and Tomlin follow the equation D = 1.3 exp (-95,00O/RT) cm2/sec In view of recent diffusion data for ß zirconium3 and 0 titanium4 in which Arrhenius-type plots do not yield straight lines and of the potential high- temperature uses of niobium and its alloys, we thought it important to investigate the diffusion behavior of this bcc refractory metal over a large temperature range. This has recently been done for molybdenum,5 chromium,6 vanadium,"" and tantalum.9 Niobium was a particularly suitable material for this study largely because of the development of an anodizing and stripping sectioning technique which enables diffusivities as small as l0-19&apos; sq cm per sec to be determined accurately.10 In addition to self-diffusion data, data were obtained for the diffusion of Ta-182 in niobium and for the effect of varying oxygen content on self-diffusion. I) EXPERIMENTAL PROCEDURE Materials. The niobium was obtained from three sources: 1) melting stock from Shieldalloy Corp., 2) electron-beam melted single crystals, 1/2 in. diameter, from Semi-Elements, Inc., and 3) oxygen-doped, electron-beam melted single crystals from Materials Research Corp. The melting stock was electron-beam melted and specimens 5/8 in. diameter by 1/2 in. long were machined from the center of the bar. The analysis supplied by the vendor and an interstitial analysis of one of the specimens are given in Table I. The single crystals (type 2 above) were cut with a jeweler&apos;s saw to specimens about 3/8 in. long. The interstitial analysis of this material is given in Table 11. This material was used

Jan 1, 1965

By R. W. Raymond

AT the Pittsburg meeting of the Institute, in March, 1910, the death of Mr. Metcalf was announced, and Col. H. P. Bope, of Pittsburg, delivered in memory of him a brief but eloquent address, which, though expressing the sorrow of Mr. Metcalf&apos;s friends, and, in general terms,. the debt of gratitude which his country and his profession owed to him, was not intended to be a complete survey of his life and work. With Colonel Bope&apos;s permission, and with the aid of some of the statements in his address, I substitute for it, in our Transactions, this more detailed, yet still inadequate memorial. As Colonel Bope justly remarked, the men who could do justice to this theme-such men, as Jones, Chalfant, Bennett, Oliver, and Park-passed away before Metcalf, leaving him almost the last of the generation of great steel-makers who made Pittsburg the Sheffield of America, and who discharged a double function, as the rear-guard of the old metallurgical practice and the van-guard of the new. I knew many of them; would that I were better qualified to celebrate their achievements. William Metcalf was born Sept. 3, 1838, at Pittsburg, Pa., where his father, Orlando Metcalf, was an eminent member of the bar. At the age, of sixteen, he entered the Rensselaer Polytechnic Institute, at Troy, N. Y., from which he was graduated in June, 1858. Returning to his native city, he became an assistant engineer in the Fort Pitt Foundry, of which. he was made Superintendent in 1859. This famous establishment produced the largest castings and heaviest machinery then known in the United States;-and Mr. Metcalf&apos;s intense, intelligent and incessant study of his business prepared him as a manufacturer for a patriotic service to his country more valuable than, as a soldier, he could have rendered in the field. The call came in 1862, when the government needed, above all things, a supply of field, naval and siege artillery. The

Apr 1, 1911