Search Documents

By W. W. Gerberich

SINCE the original formulation of fracture mechanics concepts,&apos;y2 relatively little work has related the fracture mechanics description of metal behavior on a gross, structural component scale to the behavior of its microstructural constituents. The purpose of this note is to suggest the utilization of fracture mechanics to describe material behavior on a microscopic scale. A Fracture Concept for Two-Phase Structures. A critical displacement concept considering the tough unidirectional phase in a relatively brittle matrix is first examined. It is assumed that a flaw exists at position 1 as depicted in Fig. 1. As the crack moves from position 1 to 2 the plastic zone could be of the shape described with the size approximated by the Dugdale3 model: where c is the half-crack length, OO is the applied stress, and oyS is the yield strength. Hahn and Rosen-field4 have presented a simple fracture criterion for homogeneous materials based upon the displacement at the crack tip. They also have shown the equivalence of the critical displacement, v*, to fracture toughness by Kc = (2v*oysE)1/2 [2] The displacement at the crack tip is given by and the displacement at any distance in front of the crack tip may be determined knowing the plastic zone size and utilizing the development of Goodier and Field.5 Recalling Fig. 1, the value of v* for fracture in material M1 may be calculated from Eq. [2] providing the critical stress intensity factor is known. As the material is loaded, when vc > vM1 the crack moves from position 1 to position 2 where it encounters the tough second phase. If vc2 < vm2, then the crack will be arrested providing the width of the M2 phase is sufficiently large. This condition is necessary since the displacement at position 2 has increased due to the longer crack length. Thus, the displacement at the distance X (representing the dimension of the second phase) in front of the crack may be larger than the critical displacement for failure in the brittle material. If v, > vm, then failure will proceed in the brittle material. The value of v, may be calculated as indicated above. This latter consideration is the same as predicting fracture of a brittle second phase at some distance in front of a crack located in a ductile matrix. Experimental Evidence. On a macrostructural scale, tungsten wires in a ductile Be-Cu matrix are seen to fracture well ahead of the main crack front in Fig. 2. Utilizing a Kc value of 14.2 ksi-in.1/2 obtained by Schroder et al.6 for as-received tungsten, the critical displacement 2v*, for fracture is calculated from Eq. [2] to be about 6.5 X 10-5 in. The crack tip displacement, 2vc, is calculated from Eq. [3] to be 0.0028 in. indicating that fracture would occur at a considerable distance in front of the crack tip. From the ratio of v*/vc and the plastic zone estimate of Eq. [I], the distance in front of the crack tip at which a tungsten wire should fracture is calculated to be about 0.195 in. As shown in Fig. 2, a fractured wire occurs at a distance of 0.140 in. (fractured in three places), not at 0.250

Jan 1, 1968

By J. M. Boutwell

PAGE I. Introduction,.......541 II. General Geography,......542 III. General Geology,......544 1. Sedimentary Rocks,..... 544 2. Igneous Rocks,...... 545 3. Areal Geology,.......546 4. Structural Geology......547 IV. General Character of Ore-Deposits,...548 V. Genesis of the Disseminated Ore in Monzonite,.... 549 1. General,........549 2. Character and Occurrence,... 649 3. Genesis,....... 550 4. Superficial Alteration.....553 5. Conclusion......553 VI. Genesis of the Ore in Fissures,...553 1. Character........... 553 2 Occurrence......554 3. Deposition...... 556 4. Transporting Agent....555 6. Immediate Causes of Deposition..556 6. Superficial Alteration....564 7. Conclusionl ..... 565 VII. Genesis of the Copper-Ore in Limestone...... 566 1. Character......566 2. Occurrencel .....566 3. Deposition......567 4. Relation of Fissures.....569 5. Relation of Intrusives,...571 6. Superficial Alteration....575 7. Conclusion......578 VIII. Periods of Ore-Deposition....578 IX. Dates of Mineralization.....579 X. General Conclusions.....580 I. Introduction. The object of this paper is to present a concise statement on the genesis of the copper- and lead-deposits of the Bingham

Jan 1, 1906

By C. R. Kuzell

GEOGRAPHICAILY the industry of reducing and refining of copper continued to migrate from the .United States during 1931. While this country is losing the predominant position of its copper industry, our engineers still enjoy their pre-eminent position as leaders in the design and operation of the new plants being brought into production in the four quarters of the globe. Progress in the art, as indicated by the construction of the recently completed works, has not been revolutionary. Standard methods have been followed, augmented by novel features in flow-sheets demanded by the results of progress in the art of ore-dressing, and by reason of problems incidental to the peculiarities of the new ores being treated. Design and construction progress has likewise been orderly and without radical departure from less recent practice; new features in primary and secondary equipment being logical developments to provide for special conditions to keep abreast of improve¬ments in accessory apparatus. The new plants are being rapidly brought in without hazardous novelties and for the purpose of yielding the principal ingredient, copper, in as large a volume as it will he possible to market; the old United States procedure. In the meantime the domestic plants are shut down or operating at a very low capacity, threatened with untimely demise unless the metallurgist can extract and develop other valuable products from the ores. International agreements .and tariff protection may be a temporary reviving stimulant, but for many mines the days of profit will be numbered unless the ores can be made to yield as values the ingredients now being discarded. Invisible progress in this direction has been made during the past year, and it is to he hoped that time will prove that the outstanding progress of 1931 was in the development of processes for the ultimate recovery of by-products from copper ores, perhaps even relegating the value of the copper yield to secondary importance.

Jan 1, 1932

By AIME AIME

AT bottom of this page is a photograph recently taken by a student-John E. Stewart-of the most northerly situated college in the world, the Alaska Agricultural College and School of Mines. It is situated at College, near Fairbanks, Alaska, approximately on the 65th parallel of latitude, and therefore just south of the Arctic Circle. It is farther north than Hudson Bay, and in about the same latitude as southern Greenland.

Jan 1, 1932

By Howard H. Fields

Any mining engineer with a desire to operate independently, with some financial backing, and with no fear of heavy responsibility and long hours, should be able to make a comfortable living in Mexico. Barring a few inconveniences such as a lack of satisfactory liability or accident insurance, the difficulty of obtaining repair parts or vehicles, and the length of time required to receive returns from shipments, the operation of small mine is not at all difficult. It is, in fact, a little easier to find a good prospect in Mexico than in the U.S.

Jan 1, 1950

By O. W. Ellis

The writer has dealt with the effect of various methods of melting copper upon the gas content of the metal.&apos; The copper referred to in his earlier paper was melted in the foundry both in the oil furnace and the electric furnace. As the metal did not measure up to conductivity standard, the term "casting copper" was applied to the material in the title of the paper. It was thought that some information in regard to the gases in a sample of overpoled copper might also be of interest, and through the courtesy of C. R. Stevens, superintendent of the copper mill of the West-inghouse Elec. & Mfg. Co., such a sample was obtained. The metal was chill-cast in the form of an ingot about 7 in. long, 2 1/2 in. deep (from the base to the raised surface of the ingot) and from 1 3/8 to 1 7/8 in. wide. A photograph of part of the ingot is shown in Fig. 1. The effect of over-poling on the surface of the metal is here quite clearly shown.

Jan 1, 1929

By O. W. Ellis

The writer has dealt with the effect of various methods of melting copper upon the gas content of the metal.&apos; The copper referred to in his earlier paper was melted in the foundry both in the oil furnace and the electric furnace. As the metal did not measure up to conductivity standard, the term "casting copper" was applied to the material in the title of the paper. It was thought that some information in regard to the gases in a sample of overpoled copper might also be of interest, and through the courtesy of C. R. Stevens, superintendent of the copper mill of the West-inghouse Elec. & Mfg. Co., such a sample was obtained. The metal was chill-cast in the form of an ingot about 7 in. long, 2 1/2 in. deep (from the base to the raised surface of the ingot) and from 1 3/8 to 1 7/8 in. wide. A photograph of part of the ingot is shown in Fig. 1. The effect of over-poling on the surface of the metal is here quite clearly shown.

Jan 1, 1929

By W. R. Ingalls

THE propaganda in favor of the adoption of the metric system of weights and measures in the United States is founded upon the idea of compulsory adoption. There can be no argument about this, for the metric system has been legal, by Act of Congress, in the United States since 1866. Nobody ought to oppose an educational movement, and if pro-metric activities were confined to that there might be no reason to gainsay them. I do not propose to enter into any discussion of &apos;the relative merits of the metric and the English systems of weights and measures. The simple case is that the metric system not having made much headway in the United States after more than 50 years of legality, &apos;it is now aimed to force it upon the people by legislative compulsion. The main arguments in favor of such compulsory adoption are that it would- simplify the education of our children and would promote our foreign trade, for the reason that more countries of the world, with which we do business, use the metric system than the English system. I am going to disregard,&apos; in this contribution, the first of these arguments, for it is largely conjectural." Not so with the other, which is specific, and being so its speciousness can be, proved. It is true that the metric system is used by more countries of the world than the, English system. It is commonly stated that of the Indo-European nations only the United States, Great Britain, and her colonies, and Russia have failed to adopt it. However, if with "colonies" we equate Canada, Australia, New Zealand, Tasmania and South Africa, we have a longer list of non-metric countries, and it comprises not only the most populous, but also the most industrial nations of the world.

Jan 1, 1921

By B. A. Joyce, R. W. Bicknell, R. J. Bennett, P. J. Etter

Epitaxial layers of silicon have been grown on single-crystal quartz and alumina by two types of chemical reaction the hydrogen reduction of trichlorosilane and b) the pyrolysis of silane. These reaction systems are described. The cqsfallography of the two systems, as determined by electron and X-ray diffraction, is discussed, and epitaxial mechanisms suggested. The electrical behavior is briefly considered, and the design and properties of field-evert devices fabricated in the epilaxial material are also discussed. RECENT work carried out in these laboratories" has shown that it is possible to obtain epitaxial deposits of silicon on single-crystal quartz and alumina. The purpose of this paper is to describe the method of preparation of these layers using both the hydrogen reduction of trichlorosilane and the pyroly-sis of silane, to compare the crystallographic behavior of films on the two substrates, and to present some initial results of the electrical behavior of silicon layers on alumina. The structural study has been carried out using electron and X-ray diffraction and electron microscopy. The electrical assessment has been made in terms of conductivity and mobility determinations by the van der pauw3 technique, and by measurements on metal-oxide-semiconductor assemblies. 1) FILM PREPARATION Both quartz and alumina substrates, approximately 1 sq cm in area and 0.4 mm thick. were prepared from slices cut parallel to within a few degrees of (11.0), (10.0), and (00.1), and polished mechanically down to about 0.3 p diamond grade. Chemical polishing of alumina slices, using phosphoric acid at elevated temperatures, has also been used; epitaxial silicon layers have been grown on these substrates, but the process is not entirely reliable, possibly because the large strain present in the Verneuil-grown alumina crystal affects the chemically prepared surface. The two reaction systems are fairly conventional and are described briefly below. a) Trichlorosilane-Hydrogen System. The apparatus is shown schematically in Fig. 1. The substrate was heated by induction, with a fused-quartz encapsulated graphite hemicylinder as susceptor. The procedure for carrying out a deposition was to heat the substrate to reaction temperature in a stream of

Jan 1, 1965

By R. F. Mehl, R. W. Parcel

THE rate of the decomposition of austenite in eutectoid steels, forming only pearlite, may be expressed fundamentally in terms of the rate of nucleation and the rate of growth of pearlite nodules. This matter has received much attention in recent years. (The basic references are listed in ref. 1; references of particular import to the present work will be given separately.) Systematic data have been developed for plain carbon eutectoid steels.:! Although the physical factors affecting the rate of nucleation, N, in case of plain carbon steels have presumably been identified, they cannot as yet be evaluated quantitatively.&apos; Several somewhat successful attempts, however, have been made to calculate the rate of growth, G. In the latter case the important factors determining the edgewise growth of pearlite have been assumed to be: 1—the interlamellar spacing; 2—the concentration extremes and concentration contours of carbon in austenite in front of the growing pearlite interface; and 3—the rate of diffusion of carbon in austenite.* The only systematic data on N and G for pearlite in alloy eutectoid steels are those for Co-steels;6 there are no data on alloy eutectoid steels in which the alloying element is known to decrease the rate of formation of pearlite, apart from a few scattering data reported earlier&apos; for steels containing manganese. This paper reports a systematic study of N and G for eutectoid alloy steels containing molybdenum and nickel, respectively. In order to provide information of help in understanding the results, new data are presented on the effect of molybdenum on the interlamellar spacing of pearlite, So; data on the effect of nickel on So have already been published.&apos; The alloys used were in five groups: 1—Pure Fe-C-Mo alloys (Table I) were supplied by the Climax Molybdenum Company of Michigan, Detroit. They were made from Armco ingot iron of standard analysis, Acheson graphite, and ferro-molybdenum, melted in silica-lined crucibles in a high frequency induction furnace. The ferromolyb-denum was added to the melted steel, followed in 5 min by 0.08 pct Al. The ingot as-cast measured 23/4x 31/4x10 in.; it was hot-forged at 1150°C to a bar 1 in. sq.

Jan 1, 1953

By E. Stansfield

THIS test was described in a privately circulated First Progress Report on Slacking Characteristics of Coal, by A. C. Fieldner and W. A. Selvig, May 1, 1928. The test was described in detail in U. S. Bureau of Mines Report of Investigation 3055, in November, 1930.1 The test, in brief, is conducted as follows: A sample of freshly mined coal consisting of 18 to 25 pieces approximating 1 ¼ cubes, and weighing 500 to 600 grams, is taken for the test. The sample is subjected to a "blank sieving" of carefully regulated degree, on an 8-in. circular sieve with 0.263-in. square openings; and the undersize and oversize weighed. The oversize is placed on a sheet-iron pan and dried for about 24 hr. in an A.S.T.M. air-drying oven maintained at 30° to 35° C. through which a current of warm air is drawn. The sample is then cooled to room temperature and immersed for one hour in water at the same temperature. The water is then drained off, the sample dried for 24 hr. as before, cooled, sieved as before, and the oversize and undersize weighed. The percentage weight of the undersize, is calculated and reported as the first cycle loss. This loss, corrected by subtracting the percentage loss in the blank sieving, is termed the slacking index. The sample may be subjected to further cycles of wetting, draining, air-drying, sieving and weighing. In a letter (August, 1932) W. A. Selvig approved making the blank sieving on a duplicate sample, rather than on the sample used for the test, where sufficient coal was available. This method is now employed in these laboratories. The accelerated weathering test has been employed in the labora-tories of the Research Council of Alberta, at Edmonton, since 1928, but not found entirely satisfactory as repeat determinations with samples taken from the same or adjacent mines frequently showed serious differ-ences. Differences must be expected as the coal may vary in the seam, and the selection of a typical set of lumps approximating 1 ¼ -in. cubes

Jan 1, 1934

By D. H. Forbes, H. M. Manasevit, F. L. Morritz

Single-crystal thin films of molybdenum have been grown. by the pyrolytic decomposition of molybdenum hexafluoride in a hydrogen ambient on various insulating substrates at temperatures front 650° to 900° C. Single-crystal discs of various orientations of magnesium aluminate spinel, a aluminum oxide, magnesium oxide, and the natural facets of beryllium oxide were all observed to exert epitaxial control on the depositing film. Determinations of the crystallographic relationships existing between film and substrates have been made, using X-ray diffraction three-circle goniometry and Laue back-reflection techniques. Using these data, crystallographic overlays have been constructed which suggest a possible interfacial geometry on the basis of a match between metal deposit atoms and metal ion sites in the substrate. A continuing program has been in effect in the Auto-netics Laboratories over the past several years aimed at the development of electronic materials in new and useful forms using chemical vapor deposition techniques. During the course of these investigations, the epitaxy of silicon1"5 and tungstenep7 on single-crystal metal oxide insulators was studied extensively. The deposition of molybdenum is a logical extension of the tungsten work since the crystal structure is identical and the lattice dimensions differ by less than 1 pct. The pyrolytic decomposition of molybdenum hexafluoride in hydrogen was used to grow molybdenum films on the oxide substrates AlzOs, MgA1~04, MgO, and Be0 at from 650" to 900°C, depending on the substrate material. Under the experimental conditions to be described, monocrystalline films of controlled orientation were obtained. The materials investigated and their crystal structure are listed in Table I. EXPERIMENTAL The molybdenum depositions were effected by the hydrogen reduction of molybdenum hexafluoride (MoFe) in a flowing system of hydrogen at atmospheric pressure. The schematic of the apparatus is shown in Fig. 1. The hydrogen, purified by passage through a heated palladium thimble, was mixed with the vapor of the liquid MoFe maintained in a steel bottle at room temperature (25°C). The mixture was passed over the substrate, which was heated by rf induction of a sup-

Jan 1, 1969

By C. E. Reistle, G. L. Nye

The East Texas field is in Smith, Rusk, Gregg, Upshur and Cherokee counties, Texas. The discovery well was completed Sept. 8, 1930, near the eastern limit of the field. Within less than one year the new field became the dominant factor in the world production of crude oil. On Aug. 16, 1931, eleven months after completion of the discovery well, there were 1644 wells in the field, and the average daily production was 584,475 bbl. Since that time the number of wells has increased to 8195 on Oct. 1, 1933, and the field has produced 385,979,691 bbl. of oil. The geology of the East Texas field has been discussed by Lahee,1 Levorsen,2 Minor and Hanna3 and others, and it will not be discussed in detail here. The field is a structure of the monocline type on the westward dipping homocline between the Sabine uplift and the East Texas geosyncline. Production is obtained from the Woodbine group, which has been truncated and then sealed by the Austin chalk, which rests unconformably upon it. The oil-saturated part of the sand lies bettween a sub-sea depth of 3050 ft. on the east side of the field, where the Woodbine sand stops and the Austin chalk rests directly upon older formations, and a sub-sea depth of 3320 ft., which was the average depth of the water table in the sand at the time the field was discovered. The field is about 40 miles long and has an average width of approximately 4 1/2 miles. The area within the proven limits of the field is close to 116,580 acres and the normal Woodbine water underlies nearly 62,000 acres on the western side of the field at the present time. The field is unusual in several respects: (1) the tremendous size of the reservoir system and the quantity of oil in place; (2) the large area of the oil and water contact, which makes water movement possible into the oil-bearing part of the structure; (3) the absence of free gas within the main producing sand of the field. Changes in the reservoir pressure during the production history of the field have been greatly affected by

Jan 1, 1934

By Sheldon P. Wimpfen, Ralph H. Sweefser

FOR centuries the pumping of water has been one of the chief problems to be overcome by the persistent men who win the mineral wealth of the world. Profitable operations have often been forced to suspend activities as the mine penetrated well below the water table or when sudden rushes of water were encountered. To operate below the local water level requires continuous pumping equal in volume to the amount of water flow¬ing into the mine workings. Often the water to be removed exceeds the tonnage of valuable material produced. To be above local water level is a valuable asset. Modern mining practice permits nothing short of the extraction of the last pound of profitable ore from a mineral deposit. In the days before the development of mechanical and electrical power as we know it today. water in any quantity was a major

Jan 1, 1948

By AIME AIME

ON Thursday, Oct. 9, oil men from far and wide gathered at Beaumont, Texas to participate in a three-day celebration of the fortieth anniversary of the completion of the famous Lucas gusher well at Spindletop field just south of Beaumont, and to pay tribute to Anthony F. Lucas, for whom the Lucas Medal of the A.I.M.E. is named. In the afternoon the gathered host drove to the site of the discovery well to dedicate a 58-ft. granite monu¬ment erected on the spot where the original derrick stood. Representatives of the A.I.M.E. took a prominent part in the dedication ceremonies, giving the two principal addresses of the afternoon&apos;s program. Everette DeGolyer, past President, paid a personal tribute to Capt. Lucas, as a pioneer producer, an engineer, and a friend and well wisher of all young engineers. He gave a splendid picture of the useful and full life of Capt. Lucas who always took a great interest in the activities of the Petroleum Division of the Institute, from its inception to the time of his death.

Jan 1, 1941

By R. F. Mehl, W. Batz, C. Wells

Diffusion coefficient values for carbon in austenite covering a wide range of temperature and composition have been determined employing statistical methods. In addition, the relation between concentration and each of the following, D (diffusion coefficient), Q (activation heat of diffusion), and A (the constant in the diffusion equation), has been obtained. A study of the rates of diffusion of austenite was published in Metals Technology in 1940.&apos; The present investigation is an extension of the earlier work, undertaken (1) to obtain values of the coefficient of diffusion, D, over a much wider range of carbon concentration, and (2) to provide data in all ranges of concentration and temperature in such abundance that statistical methods could be employed to evaluate the accuracy of the data with unusual precision. Composition of Materials: Composition of materials used in this research program are listed in table I. These materials, all forged to about 1 1/4 in. rounds, consist of a high-purity iron, Armco iron, a large number of laboratory-made plain carbon steels containing amounts of impurities normally expected in high-quality commercial steels, and three silicon steels. Since it was known at the time these steels were being made that impurities in the amounts present were unlikely to affect carbon diffusion rates&apos; significantly, the effort made to obtain high-purity steels was not as persistent as it otherwise would have been. Procedure: In general, the procedure followed by Wells and Mehl and described&apos; in detail in an earlier publication&apos; is the one used by the present authors. However, certain modifications have been made which it is believed allow diffusion data to be interpreted more objectively and correctly. These are described completely under appropriate subheadings which follow. Experimental Procedure: Experimental procedure includes (1) the preparation of specimens by welding steels of different carbon contents, (2) the heating of these for certain times at selected temperatures in order to diffuse carbon along the specimens across the welded "interface," and (3) the determination of the carbon distribution across the diffusion zone. Preparation of Specimens: Prior to welding steel of one carbon content to iron or steel of another carbon content, surfaces to be welded are machined perpendicular to the longitudinal axis of cylinders which are about 3/4 in. in diam and 1 1/2 in. long. The prepared, flat, parallel surfaces are brought together and butt-welded electrically. Evidence of a good weld is given in fig. 1. Welding temperature

Jan 1, 1951

By A. Bar-Or, G. Hirsch, P. Wynblatt

The rates of nucleation and growth at various temperatures in U-0.45, 1.1, and 1.35 at. pet Cr alloys were determined, providing a qliantitative proo-f that the transformation under study is controlled by nucleation and diffusional growth. The linear relationship, log NV US 1/T2, suggests that the nucleation of the alloys is probably controlled by the classical law of nuclei formation. The established linear relationship, log G us 1/T, in the three alloys suggests that growth in each alloy is controlled by bidimensional nuclei formation. It was established that both the rate of growth and the rale of nucleation are retarded by chromium. Using classical formulae, sApN and sApG (the ß/a apparent interphase energies) were calculated from the nucleation and growth results, respectively. It was found that their values are of the same order of magnitude. However, why sApN is unaffected by the addition of chromium, while sApG increases with it, needs further clarification. In the last few years, an appreciable amount of research has been conducted into the mechanism of the ß —a transformation in uranium and uranium alloys. Recently, Burke1 reviewed the published work concerned with this transformation. He concluded that in dilute uranium alloys it is firmly established that, at high temperatures in the a range, ß decomposes by a diffusional process. However, he based his conclusion either on experiments dealing with the over-all transformation,2 or on qualitative results.3 It was felt that a better insight into the mechanism of transformation could be gained from the quantitative measurements of growth and nucleation rates, which we aimed to carry out in the present work. In a previous work,4 we have shown that a rim of a grains is formed during isothermal transformation at the high a range. The thickening of this rim with time was used for measuring the rate of growth in U-0.45 at. pet Cr.5 This method was also used in the present work for two more alloys. For meas- uring the rate of nucleation, a method of quenching and macroetching was developed to allow differentiation between a grains formed during isothermal transformation at the upper a range and those formed after quenching, Fig. 1. EXPERIMENTAL WORK AND RESULTS The Rate of Nucleation. The measurement of the rate of nucleation was effected by counting the num-

Jan 1, 1965

By W. E. C. Coxe

Many of you who are interested in the manufacture of iron and steel, have no doubt heard of the "Wheeler process for combining iron and steel." Mr. Wheeler has formed a company, styled the "Combination Trust Company," whose business is to grant licenses for the use of this patent process in producing what he calls "iron-clad steel." It has been proposed to apply it in the manufacture of car or wagon axles, also to shafting, having steel cores or centres covered with iron; to tubes of steel with an inner and outer skin of iron ; to structural purposes, such as girders and beams; bridge and tie-bolts, where the strength of the iron and the rigidity of the steel would be desirable. In answer to a request from Mr. Wheeler, permission mas accorded him to make some experiments at the rolling mill of the Philadelphia and Reading Coal and Iron Company, at Reading, Pennsylvania, with a view to manufacturing some steel-headed rails. In making this kind of a rail two difficulties are encountered. If the iron is brought to the requisite heat to weld properly, the steel is likely to be burned; if the steel is cared for, to prevent burning, the several layers of iron are not brought up to the proper welding heat. Mr. Wheeler claimed that the steel slab covered with iron which he furnished for the head of the rail could net be injured by any heat to which it might be subjected in the ordinary course of heating the rail-pile. He claimed, also, that by this method the porosity, which he thought was characteristic of all solid rails of Bessemer steel, would be overcome. Four steel slabs were furnished for this experiment, being Bessemer steel of .61 carbon, made at the Edgar Thomson Steel Works, and covered with iron in one of the Pittsburgh mills. The slabs were in section seven inches wide by three inches thick, and the iron covering was one-eighth to three-sixteenths inch thick. Each slab was placed on a pile of iron made up in the ordinary way for a rail fifty-six pounds per yard and thirty feet long. The heating was under the personal direction of Mr. Wheeler, and

Jan 1, 1879

By Karl W. Mote

CALIFORNIA&apos;S iron and steel industry had its beginning in San Francisco in 1849 when the first iron casting was poured at the old Union Iron Works. Soon after, in 1856 at Grass Valley, enough iron ore was smelted to supply pig iron for the castings of a quartz mill there. From 1880 to 1886, iron ore was produced from the Hotaling mine in Placer County and converted to pig iron in a local blast furnace using charcoal. From 1907 to 1914, the Noble Electric Steel Co. produced pig iron from iron ore mined at the Shasta Iron Co. mine, and followed this for three years in the production of ferro-alloys. Between 1917 and 1941, the State&apos;s industry in- creased its capacity for open hearth and electric furnace scrap treatment, but the real impetus was supplied by the need for more steel at the beginning of World War II. The result was the State&apos;s first integrated steel plant-the Kaiser Steel Corp. facilities at Fontana.

Jan 7, 1958

By AIME

BILL BREWSTER was a natural for the steel business. His family lived at Iron Mountain, Mich., when Bill was born on June 14, 1889, so that he had iron in his blood. Always he has looked toward the finished product, rather than the raw material, so that it was a fore-gone conclusion that he should work toward the steel end of the business. After preparing for college at Hotch-kiss Academy he entered the Sheffield Scientific School of Yale University from which he graduated in 1910 with the degree of Bachelor of Philosophy. No reunion of his class would be complete without Bill Brewster. Unlike many of us who try several jobs before settling down, Bill shot straight for the mark. After a summer&apos;s work at Iron Mountain, making sure of his background in the production of the raw iron ore, he entered the employ of Wisconsin Steel Works of the International Harvester Co. in September 1910 and has been there ever since. It wasn&apos;t much of a job to start with, just a laborer in the billet dock department, but soon there was an opening in the blast-furnace department, where he started as superintendent&apos;s clerk in December 1910.

Jan 1, 1946