Search Documents

By James Pollock

The possibility of colloidal deposition of cinnabar has been neglected. In opalite deposits cinnabar exists in particles within or near the colloidal size range. Colloidal processes have been admitted to be operative in hot springs and low-temperature deposits similar to most cinnabar deposits. Mercuric sulphide sols are stable to elevated temperature and pressure, and in nature probably are chiefly affected by the electrolytes in solution, dilution of colloid, and presence of protective colloids as silica. The stability of mercuric sulphide sols to electrolyte is measured, and shown to be greatly increased by dilution and by the protective action of silica. Mercuric sulphide sols follow the Schulze-Hardy valency rule, therefore the precipitating power of complex mixtures of electrolytes can be computed roughly. The stability of mercuric sulphide sols is shown to be greater than the equivalent precipitating power of the electrolytes in a hot spring depositing mercuric sulphide. It is concluded that finely divided or earthy types of cinnabar are colloidally deposited. Possibility of Collodial Deposition While colloidal solution has been suggested as a means of transport for a number of minerals, such as the sulphides of antimony, arsenic, and iron, it has been neglected in connection with mercury. This is surprising because there exists positive evidence that cinnabar is present in certain deposits in particles of colloidal or near colloidal size. Colloidal transport could result from either the rapid dilution or neutralization of alkaline sulphide solution bearing mercury coming in contact with deep ground waters, or from colloidal solution near the original source and subsequent flow to the point of deposition unchanged. That the dilution of a mercuric alkaline sulphide solution will precipitate mercury sulphide in colloidal form has been demonstrated a number of times and is easily confirmed. The dilution hydrolyzes the alkaline sulphide Na2S to the corresponding hydroxide and hydrosulphide NaOH and NaHS, and the diminution of the concentration of alkaline sulphide reduces the solubility. It is not the contention of this writer that colloidal deposition is the mode of transport of mercuric sulphide in all mercury deposits, but that the stability of a mercuric sulphide sol, as demonstrated below, in waters that are similar to those that have deposited mercuric sulphide necessitates consideration of this possibility in many deposits, especially those of the hot-spring and so-called opalite type. Evidence of Colloidal Deposition Ross1 has shown that most deposits of quicksilver are formed at low temperatures and pressures, and probably by solutions that have relatively simple chemical compositions. In most cases the solutions are probably similar to those observed in hot springs, and in two instances—at Steamboat Springs, Nevada, and Sulphur Bank, California—hot springs have been reported by Becker as actually depositing cinnabar.2 Opalite deposits were believed by early investigators to be surface phenomena

Jan 1, 1949

By James Pollock

The possibility of colloidal deposition of cinnabar has been neglected. In opalite deposits cinnabar exists in particles within or near the colloidal size range. Colloidal processes have been admitted to be operative in hot springs and low-temperature deposits similar to most cinnabar deposits. Mercuric sulphide sols are stable to elevated temperature and pressure, and in nature probably are chiefly affected by the electrolytes in solution, dilution of colloid, and presence of protective colloids as silica. The stability of mercuric sulphide sols to electrolyte is measured, and shown to be greatly increased by dilution and by the protective action of silica. Mercuric sulphide sols follow the Schulze-Hardy valency rule, therefore the precipitating power of complex mixtures of electrolytes can be computed roughly. The stability of mercuric sulphide sols is shown to be greater than the equivalent precipitating power of the electrolytes in a hot spring depositing mercuric sulphide. It is concluded that finely divided or earthy types of cinnabar are colloidally deposited. Possibility of Collodial Deposition While colloidal solution has been suggested as a means of transport for a number of minerals, such as the sulphides of antimony, arsenic, and iron, it has been neglected in connection with mercury. This is surprising because there exists positive evidence that cinnabar is present in certain deposits in particles of colloidal or near colloidal size. Colloidal transport could result from either the rapid dilution or neutralization of alkaline sulphide solution bearing mercury coming in contact with deep ground waters, or from colloidal solution near the original source and subsequent flow to the point of deposition unchanged. That the dilution of a mercuric alkaline sulphide solution will precipitate mercury sulphide in colloidal form has been demonstrated a number of times and is easily confirmed. The dilution hydrolyzes the alkaline sulphide Na2S to the corresponding hydroxide and hydrosulphide NaOH and NaHS, and the diminution of the concentration of alkaline sulphide reduces the solubility. It is not the contention of this writer that colloidal deposition is the mode of transport of mercuric sulphide in all mercury deposits, but that the stability of a mercuric sulphide sol, as demonstrated below, in waters that are similar to those that have deposited mercuric sulphide necessitates consideration of this possibility in many deposits, especially those of the hot-spring and so-called opalite type. Evidence of Colloidal Deposition Ross1 has shown that most deposits of quicksilver are formed at low temperatures and pressures, and probably by solutions that have relatively simple chemical compositions. In most cases the solutions are probably similar to those observed in hot springs, and in two instances—at Steamboat Springs, Nevada, and Sulphur Bank, California—hot springs have been reported by Becker as actually depositing cinnabar.2 Opalite deposits were believed by early investigators to be surface phenomena

Jan 1, 1949

By James Pollock

SUMMARY THE possibility of colloidal deposition of cinnabar has been neglected. In opalite deposits cinnabar exists in particles within or near the colloidal size range. Colloidal processes have been admitted to be operative in hot springs and low-temperature deposits similar to most cinnabar deposits. Mercuric sulphide sols are stable to elevated temperature and pressure, and in nature probably are chiefly affected by the electrolytes in solution, dilution of colloid, and presence of protective colloids as silica. The stability of mercuric sulphide sols to electrolyte is measured, and shown to be greatly increased by dilution and by the protective action of silica. Mercuric sulphide sols follow the Schulze-Hardy valency rule, therefore the precipitating power of complex mixtures of electrolytes can be computed roughly. The stability of mercuric sulphide sols is shown to be greater than the equivalent precipitating power of the electrolytes in a hot spring depositing mercuric sulphide. It is concluded that finely divided or earthy types of cinnabar are colloidally deposited. POSSIBILITY OF COLLODIAL DEPOSITION While colloidal solution has been suggested as a means of transport for a number of minerals, such as the sulphides of antimony, arsenic, and iron, it has been neglected in connection with mercury. This is surprising because there exists positive evidence that cinnabar is present in certain deposits in particles of colloidal or near colloidal size. Colloidal transport could result from either the rapid dilution or neutralization of alkaline sulphide solution bearing mercury coming in contact with deep ground waters, or from colloidal solution near the original source and subsequent flow to the point of deposition unchanged. That the dilution of a mercuric alkaline sulphide solution will precipitate mercury sulphide in colloidal form has been demonstrated a number of times and is easily confirmed. The dilution hydrolyzes the alkaline sulphide Na2S to the corresponding hydroxide and hydrosulphide NaOH and NaHS, and the diminution of the concentration of alkaline sulphide reduces the solubility. It is not the contention of this writer that colloidal deposition is the mode of transport of mercuric sulphide in all mercury deposits, but that the stability of a mercuric sulphide sol, as demonstrated below, in waters that are similar to those that have deposited mercuric sulphide necessitates consideration of this possibility in many deposits, especially those of the hot-spring and so-called opalite type. EVIDENCE OF COLLOIDAL DEPOSITION Ross1 has shown that most deposits of quicksilver are formed at low temperatures and pressures, and probably by solutions that have relatively simple chemical compositions. In most cases the solutions are probably similar to those observed in hot springs, and in two instances-at Steamboat Springs, Nevada, and Sulphur Bank, California-hot springs have been reported by Becker as actually depositing cinnabar.2 Opalite deposits were believed by early investigators to be surface phenomena

Jan 1, 1944

By Martin Coryell, Eckley Coxe, R. P. Rothwell

WILKES-BARRE, PA., April, 1871. THE great development of the mines and metallurgical works of this country during the last few years, accompanied as it has been by the investment of enor¬mous sums of money in purchasing lands, and in the erection of improvements, requires that advantage should be taken of the accumulated knowledge of engi¬neers, superintendents, and others, in mastering the problems which are con¬stantly presenting themselves for our action. Among those may be mentioned the consideration of more economical systems of mining in our coal and metal¬liferous mines, improved methods of transportation above and below ground, unwatering and ventilating mines, the mechanical preparation of coal and other minerals, the various metallurgical processes, and, in fact, every question tending to the attainment of two great objects 1st. The more economical production of the useful minerals and metals. 2d. The greater safety and welfare of those employed in these industries. In European countries, where the arts of mining and metallurgy have long been the subject of the most careful study, no means have been found so effectual in attaining the end above proposed as the free interchange of experience among those actually engaged in these industries, and this object has been accomplished, mainly, through the medium of institutes, associations or societies, composed of those engaged in these occupations, and by the- periodical publication of essays or papers, communicated to such societies by their members. It must be evident to all practical men that the interchange of the varied experience of those engaged in such occupations in this country could not fail to advance very materially the desired objects; it is, therefore, proposed to establish an American Institute of Mining Engineers, which will hold its meetings periodically in the great mining and metallurgical centres, where works of interest, such as mines, machine shops, furnaces, and other metallurgical works, can be inspected, and the members exchange their views, and consult for mutual advantage upon the difficulties encountered by each; these transactions or proceedings, when published, would form a most valuable and greatly-needed addition to our professional literature. It is proposed that a meeting of those sympathizing with the object above men¬tioned shall be called for the purpose of organizing such an association, the place and time of meeting being Wilkes-Barre, Pa., and the month of April or May. Communications indicating the opinion and wishes of all, both as to these points, and also as to the organization and objects of the Institute, will be gladly received by any of the undersigned, and a notice of the date of meeting, which will be arranged to suit the greater number, will be duly communicated. Any

Jan 1, 1873

By Thomas Adair

Moderator-Thomas Adair is now a tunnel consultant with Perini Corp., Spring Lake, N.J. He has had 40 years experience in tunnel and shaft-sinking work in both soft and hard rock, as well as subaqueous rock. He has used moles in various locations and has traveled around the world studying the problems. SOME BRIEF COMMENTS ON "MOLES" by Thomas Adair We of the Perini Corp. have been, over the past 15 years, in the forefront of the battle to develop the mechanized miner. We have contributed much to pioneer, develop, and promote the use of the mining machine. Our money and talent have not been spared in this effort. However, we are sorry to say that as of the present time (1968), at least from the economic stand- point, this effort has not been very rewarding. But, I must say to those who are presently involved in the work of building mining machines, do not be discouraged. There is money in it. We of Perini Corp. know because we put it in there. It has been estimated that during the next 15 years, some $20 billion will be spent on underground excavation; more than 13 thousand miles of sub- surface tunnels will be excavated throughout the nation. An aggressive, properly structured research and development effort would produce, within the next five or ten years, a better excavation technology and improved boring system capable of reducing present costs drastically, with a resultant great saving. The time for this effort is now, but where the enabling money for this effort will come from, I have no idea. Machine builders should be encouraged to design and develop a shield- type boring machine capable of continuous mining through varying types of ground or rock by incorporating the possibility of making minor modifications such as change of bit type, power package, etc. Such a machine could

Jan 1, 1970

By Robert Linton

IN 1898, Joseph L. Giroux and J. A. Snedaker organized the Pilot Knob Copper Co. and began developing the Pilot Knob mine at Kimberly, Nev., for high-grade copper ores, carrying good gold and silver values that the formation had disclosed. At that time the nearest railroad was over 150 mi. distant. The high-grade ores did not prove to be extensive at this point-at least to the depth. (240 ft.) to which the work was carried-but development of neighboring claims indicated extensive deposits of sulfide porphyry ore of concentrating grade lying at shallow depth, and deeper deposits of direct-smelting oxidized ores occurring in limestone near the limestone-porphyry contact. The properties passed through the hands of several organizations, with only meager development, until acquired in 1913 by Consolidated Coppermines Co., whose holdings now comprise 3480 acres of mining claims in the Robinson district. Since that time development has been prosecuted more actively; and for the purpose of determining the most efficient and economical method of treating the ores, considerable testing work has been done during the past three years, both in the laboratory and in actual mill operations. At first, the shipments were of ore high enough in grade to be profitable even with the long wagon hauls to the railroad and prevailing freight and smelting charges. In 1905, a blast furnace and a concentrator were erected at Kimberly. On account of insufficient ore supply, the blast furnace was never blown in and later was dismantled. The concentrator as originally equipped wag operated for only about two months, both because the ore supply was not sufficient and because gravity concentration did not yield satisfactory extraction. The location and arrangement of the mill further entailed high operating costs. In 1908, the Nevada Consolidated Copper Co. began to mill successfully, on a large scale, its sulfide porphyry ores, which are similar in character to the adjacent Coppermines ores. After that time, all of the ores and concentrates produced by Coppermines Company were

Jan 8, 1920

By C. B. Post, D. G. Schoffstall

A determinatioil of the hydrogen content of molten steel by means of the Vacuum-extraction method, as reported here, consists in first casting a sample of the bath in a bomb, so that the gases evolved during solidification are trapped for analysis. A portion of the cast steel sample is then prepared and heated at a temperature of 600" to 800°C. under high vacuum, and the gaser given off during this vacuum extraction (which are shown to be hydrogen), are collected and measured. Analysis of the gases evolved on solidification and the gases in the solid sample enables an accurate determination of hydrogen in the molten steel. Fig. I shows the bomb and accessories that have been found suitable for trapping the gases evolved on solidification. The bomb is made of scamless steel pipe, approximately 7 in. long by 136 in. i.d., and welded at the bottom. An ordinary pipe cap has a vacuuni-type metal stopcock threaded and brazed in its upper end. This pipe cap fits onto the bomb by means of machined threads. A flange is brazed to the pipe at the point where the cap starts to tighten up, and a rubber gasket is placed between the flange and cap. Heavy vacuum grease is used between the flange and gasket and the gasket and cap. The weight of the complete bomb and it? interval volume is known before the sample is cast. In practice, a sample of about 400 grams of steel is poured into the bomb, the funnel quickly swung out of the way, the bomb cap spun down the threads and tightened against the gasket, and the bomb set in a pail of water to keep the gasket and vacuum grease cool. It is estimated that at least 80 per cent 01 the gases evolved from the liquid sample during solidification are trapped in the bomb."

Jan 1, 1945

By Henry M. Howe

The striking features of American Bessemer practice aré its large output and its low initial silicon and initial temperature. These are interdependent. Large outputs implies short blows and short intervals between blows. Short blows imply low silicon and fast blowing. Low silicon implies short intervals and fast blowing. Our blows are short because we have little silicon to remove, and because we remove it fast by supplying blast rapidly. We get enough heat even with little silicon, because our blows and the intervals between them are so short that relatively little heat escapes from our vessels. Were we to lengthen our intervals, or to blow more slowly, we would have to meet the increased loss of heat from our vessels, either by using more silicon, or by melting hotter, i.e., by burning more coke, in the blast-furnace or in the cupola. Finally, our short intervals imply powerful machinery, efficient organization, and extreme specialization and subdivision of labor, which can be profitable only when the output is large. Let, us now take these points up in more detail, first glancing at some examples of our large outputs, given in Table I., and of the composition of our iron. Output.—On presenting such results to some foreign metallurgists, I have been told, " Oh yes, we quite understand that. You really turn out no more steel than we do. As a matter of personal pride, your manager gets up a tremendous spurt for a day, or even a week, crowds on men wastefully, rushes through great quantities of metal, and then for months afterwards has to recuperate. The machinery has been strained ; the owner's money has been wasted ; the men have been prostrated—all to gratify the manager's vanity. Your average output is no larger than ours." Personal pride has, doubtless, played its part; without it we would still be savages, or apes, or mollusks, if you prefer. These baser motives are the mudsills of progress, the soiled roots of that growth of which civilization is the flower. Great outputs were made

Jan 1, 1891

By Frank Fahrenwald

I. INTRODUCTORY METALLURGICAL research has discovered many an alloy possessing properties not combined in any single metal, and progress still consists chiefly in the investigation and utilization of alloys. In the case of iron, the demands of automobiles, high-speed machines and high-duty engines have led to the production of special iron alloys which will meet any reasonable specifications in that field. In like manner, the bronzes, brasses and other alloys of copper have been brought to remarkable perfection, and for nearly every industrial purpose some alloy has been found more suitable than the pure metal. Less complete success has attended the attempt to find substitutes for gold, platinum, and the other precious metals. Indeed, it is not likely that a material can be produced which will possess all the properties of any one of them; yet it is reasonable to hope that, for any given use, the properties required may, be found in some less expensive material. Thus, in incandescent electric lamps, the wire passing through the thick glass neck of the bulb was, until recently, almost universally made of platinum, for the single reason that no other known material, suitable as a conductor, had the same coefficient of expansion as glass. But a comparatively recent investigation of the iron-nickel series' has shown that alloys of those metals may be produced, the coefficient of expansion of which can be accurately controlled between that of iron or nickel and zero. Thus, in that particular industry, a substitute for platinum has been found. According to statistical reports, not only considerable quantities of gold and iridium, but also more than one-third of the annual supply of platinum, are used (and, in the nature of the case, irrevocably lost) by dentists. Platinum is thus employed in several forms. As a thin foil, it serves various purposes for which its high melting point, pliability, chemical resistance, and other properties-including the ease with which

Jan 1, 1916

By G. Krauss, J. M. Thompson, H. Y. Kumagai

Boron-doped p-type and arsenic-doped n-type source materials were used to deposit thin silicon films on amorphous fused quartz substrates by cathodic sputtering in argon atmospheres. All as-sputtered films were found to have high electrical resistivities of about 104 ohm-cm, despite controlled variation of the substrate temperature from 50O to 400°C. The high resistivity of the n-type films persisted even after postdeposition heat treatments as high as 1000°C, while p-type films showed a sharp decrease in re-sistivity to values on the order of 1 ohm-cm or lower after heat treatments above 650°C. X-ray and electron diffraction, together with transmission electron microscopy of the p-type films, revealed that the improved electrical properties resulted from two distinct processes. A primary crystallization or recovery within the pains, which were approximately 200Å diam in the as-sputtered films, accompanied the initial sharp drop in resistivity at 650°C. Following this process, a secondary recrystallization or discontinuous grain growth was nucleated in films heated at 1000°C. The resulting significantly increased size of certain grains and the corresponding decrease in grain boundary area accompanied an additional decrease in resistivity after heat treatment at 1000°C. The properties of thin silicon films are of interest because of their possible application in device technology. Although evaporated silicon films on amorphous substrates1-3 and both sputtered and evaporated germanium films4-' have been studied in some detail, sputtered silicon films have not been widely investigated. It has been observed that evaporated silicon films deposited at substrate temperatures below approximately 600°C are amorphous.1,3,9,10 At substrate temperatures higher than this, the films are polycrys-talline, sometimes exhibiting a fiber texture with the fiber axis normal to the substrate surface.' Similar results have been obtained with germanium films, although in this case the substrate temperature for the amorphous to crystalline transformation is reported to be as low as 150OC.5 The mechanism of film deposition by cathodic sputtering differs markedly from that of thermal evaporation. It might be expected, therefore, that the properties of sputtered and evaporated silicon films would also differ. The purpose of our study was to determine the effects of deposition conditions and heat treatments on the electrical resistivity, structure, and composition of thin silicon films sputtered on fused quartz substrates. EXPERIMENTAL DETAILS Apparatus. A schematic diagram of the sputtering apparatus is shown in Fig. 1. The vacuum chamber was enclosed by an 18-in.-diam by 12-in.-high Pyrex bell jar mounted on a stainless-steel base plate. Access holes in the base plate were used to supply argon gas to the chamber, to allow for various electrical feedthroughs, and to provide mechanical motion to the shutter between the source material and substrate. The chamber was evacuated by a pumping system consisting of a 720 liter per sec oil diffusion pump backed by a 13 cu ft per min mechanical pump. Ultimate pressures of less than 1 x 10-6 torr could be achieved. The substrates were securely mounted on the stainless-steel substrate holder by quartz tabs held in place by stainless-steel screws. Temperatures of the substrate holder were measured by a thermocouple inserted within the holder. A quartz lamp was used to heat the holder and temperatures as high as 420°C could be maintained. Deposition Conditions and Procedure. The substrates used were polished fused quartz slides 116 by 1-12 by 3 in. and were outgassed at 200°C for 1 hr at a pressure less than 1 x 10-5 torr before film deposition. This was followed by a presputtering period of 2 hr during which the movable stainless-steel shutter was so positioned that deposition on the substrate was prevented. At a sputtering voltage of 5000 v dc and an argon pressure of 0.03 torr, the cathode cur-

Jan 1, 1967

By M. O. Holowaty, C. M. Squarcy

Blast furnaces are the tools of men, and it is men who have made them great. Here is presented the story of the Ironmakers-the men who first poured hot metal into what would someday be the sinews of a nation. W HEN the Jacobean merchant adventurers bade farewell to the first ship of colonists sailing for the new land, they instructed them to direct all their skill and energy to grow silk worms in Virginia. The adventurers felt sure that they could flood the market with highly priced and much desired goods like silk, sugar, tea, and indigo. They were also convinced that they would fill the needs of the mother country for iron. Early iron production in the colonies The merchants certainly had a wonderful imagination, for silk and indigo were just as exotic in Virginia as they were in England. The settlers found it more profitable to raise tobacco on the vast stretches of the free, fertile land. Thus the plans of settlers clashed with those of The Virginia Co.; and only point of agreement was the desire to produce iron. But, even there the motives of the settlers and those of The Virginia Co. of London were worlds apart. The settlers wanted to produce the tools badly needed in the colony, while the Company desired to cash in on the rising demand for iron which the home industry could not satisfy. Both the settlers and the Company lost no time trying to find iron ore. Locations of the early mines are not known. If, however, the reports of the Irishman, Francis Maguel, can be trusted, as early as 1609 a ship sailed for England with a load of 17 tons of crude iron which the East India Co. purchased at £ 4 per ton. The iron was of excellent quality and considered the best iron made of non-English ore that was ever purchased.

Jan 1, 1961

By R. G. Hall

An article on the subject of electrolytic zinc no longer needs to be preceded by an apology. The production of zinc by electrolysis is past the laboratory stage and has become an economic factor of considerable importance in the total production of zinc in the United States. The various methods of procedure to be followed fa the greatest economy of manufacture are fairly well known, consequently a detailed description of any method is no longer necessary or desirable. In this paper I shall endeavor to lay down some of the governing conditions in this industry, the relation of methods to ore deposits, freight rates, and sources of power supply. Power Points Assuming for a moment that, for the present at least, the electrolytic production of zinc will be confined to Those localities having developed water power, a glance at these powers so developed in the United States, with their relation to known zinc orebodies of economic size, will not be without interest. Northwest In the Northwest we have water powers, developed and undeveloped, . in Washington and Montana. These must, of course, bear a close relation to the rapidly growing zinc production of the Coeur d'Alenes and of the Butte districts. In general, the power of the territory in question is relatively low-priced, at least as compared with the cost of developing power from coal, and the near neighborhood of large bodies of more or less complex zinc ores makes these water powers of more than usual interest. The same remarks may be applied equally to the developed water powers of the Canadian side of the line in the Northwest, where we have again commercially available complex ore deposits such as are being exploited today at and near Trail. California One of the large complex ore deposits of the far West is to be found in Shasta County in the immediate neighborhood of the territory of the

Jan 1, 1918

By William P. Blake

The numerous and copious reports of geological surveys made in the lead and zinc region of Wisconsin leave, perhaps, but little room for any original work, or for descriptive details of the nature and origin of the deposits not already given in the exhaustive memoirs of Percival, Whitney, and Chamberlin and their associates. HOWeyer, since the completion of the last survey, in 1879, much more attention has been given than before to the exploration of the ores of zinc, especially of late years, since the region has been better opened up by railways and the zinc industry of the country has assumed large proportions, giving a constantly increasing demand for zinc-ores. A residence of more than a year in the region, and the active direction during that time of mining operations over a considerable area, have familiarized me with the forms and peculiarities of many of the deposits; and it appears probable that some observations upon them, especially from the mining and commercial standpoint, may interest the members of the Institute. A few notes on the structure of the deposits from the mineralogical and chemical standpoints have already been presented by me to the Wisconsin Academy of Arts and Sciences." The presence of lead-ore in the soil at many points along the Mississippi river was well known to the aborigines, and early attracted the attention of the frontier traders, who purchased from the Indians the ore and even lead smelted out by the squaws. The demand for the lead-ore soon increased, and it became one of the early and potent factors determining the settlement of southwestern Wisconsin, and the development of its mining and agricultural resources. The mines of that section, together with those of Missouri and the Mississippi valley, may be said to have been the cradle of mining in the western United States. The deposits of ore being at or near the

Jan 1, 1894

By L. L. Wyman

The resultant embrittlement caused by the exposure of oxygen-bearing copper when hot and exposed to reducing gases has been the subject of many studies.' Little attention, however, has been given to the possible embrittling effects due to atmospheres or conditions that under some circumstances might be the source of a reducing gas. At rather infrequent intervals there occur reports of copper becoming embrittled during normal annealing cycles in commercial steam-atmos-phered furnaces such as customarily are used for this operation. As might be expected, several other factors exist—such as oil, dirt on the wire, or in the furnace, or metallic surface contacts—that might produce reducing gases and be the source of the trouble. However, in consideration of the statement made by Ruder,2 it would seem that under some conditions steam itself might prove to be the source of trouble. A consideration of the amount of the dissociation of water vapor up to temperatures of the melting point of copper shows that3 the amount of hydrogen that could come from this source is far too minute to account for any embrittlement. What such information does not tell is what will happen at the surface of copper when subjected to steam at elevated temperatures, for entirely different conditions may persist, which would account for Ruder's observation. Furthermore, there are no data as to what might happen at the surfaces of other materials present, the resultant of which might affect the condition of the copper present. For this reason, it was decided to make a series of experiments comparable to those previously conducted by the writer,' which would clarify the effect of the steam on copper, and in copper in the presence of steel. Material The material used in these experiments was tough-pitch copper wire of rectangular cross section, about % in. thick, picked at random from the regular factory production of material used for windings, etc., in the electrical industry. Chemical analysis of this material gave the follow-

Jan 1, 1940

By L. L. Wyman

The resultant embrittlement caused by the exposure of oxygen-bearing copper when hot and exposed to reducing gases has been the subject of many studies.' Little attention, however, has been given to the possible embrittling effects due to atmospheres or conditions that under some circumstances might be the source of a reducing gas. At rather infrequent intervals there occur reports of copper becoming embrittled during normal annealing cycles in commercial steam-atmos-phered furnaces such as customarily are used for this operation. As might be expected, several other factors exist—such as oil, dirt on the wire, or in the furnace, or metallic surface contacts—that might produce reducing gases and be the source of the trouble. However, in consideration of the statement made by Ruder,2 it would seem that under some conditions steam itself might prove to be the source of trouble. A consideration of the amount of the dissociation of water vapor up to temperatures of the melting point of copper shows that3 the amount of hydrogen that could come from this source is far too minute to account for any embrittlement. What such information does not tell is what will happen at the surface of copper when subjected to steam at elevated temperatures, for entirely different conditions may persist, which would account for Ruder's observation. Furthermore, there are no data as to what might happen at the surfaces of other materials present, the resultant of which might affect the condition of the copper present. For this reason, it was decided to make a series of experiments comparable to those previously conducted by the writer,' which would clarify the effect of the steam on copper, and in copper in the presence of steel. Material The material used in these experiments was tough-pitch copper wire of rectangular cross section, about % in. thick, picked at random from the regular factory production of material used for windings, etc., in the electrical industry. Chemical analysis of this material gave the follow-

Jan 1, 1940

By F. F. Sharpless

IT IS to be. read in Western newspapers that Hon. S. S. Arentz who introduced H. R. 7736, 'has repudiated it, that certain mining men in Utah and Nevada say that they will fight it "until hell freezes over." It is to be read in more temperate expressions that "the eminent engineers who drafted the bill exhibited a woeful misunderstanding of Western sentiment and opinion." Furthermore, it is averred that there is no need for revising the mining laws, that we have got along pretty well under the existing laws, etc. Such statements are so surprising in view of, the facts of record that it is hard to believe that the oppon-ents of the bill, who make them, are well informed, or that they represent general opinion. It will be useful therefore to review the record of the case. Our GOOD OLD MINING LAWS We have indeed got on well in our mining industry, but that has not been by virtue; of our good old mining laws. Rather has it been in spite of them. Ever since the Richmond-Eureka case in the '70s there has been litigation arising from them. Early in the '80s the apex law was discarded by common consent in Leadville, and it has been ignored in every district of flat-lying ore deposits ever since. The great mines of the present time are the porphyry copper deposits. At Bingham, Ely, Ray, Chino, Miami, Clifton and Ajo the apex law is simply inapplicable. A law that is inapplicable to the modern conditions of mining may be an old law, but it can not properly be characterized as a "good" law. For such reasons, and many others of weight, there has been a demand for revision of the mining laws; dat-ing ,back at least three decades. President Roosevelt appointed a commission to advise respecting the question, said commission comprising. Dr. James Douglas (chairman), John Hays Hammond, D: M. Barringer, Walter B: Devereux, and William B. Mather. This committee was unanimous on the following points:

Jan 1, 1922

By David Cole

At the time flotation appeared upon the metallurgical horizon in Arizona, the writer, under the direction of Dr. Ricketts, was engaged in remodeling and enlarging the No. 6 Concentration Plant of the Arizona Copper Co. at Morenci, and the work had been in progress nearly a year before the Inspiration experiments with flotation had disclosed the revolution in concentration that was at that time impending. The simplified flow sheet worked out for the remodeling of the Morenci plant had been based upon the removal of the freed metal in a minimum number of stages by treatment upon tables equipped with Butchart riffles, the latter being adapted to accomplish both classification of feed and removal of the metal at one operation, substantially as described in my previous paper.l The scheme of treatment for the slime was based upon the well-known fact that after copper sulphides, such as chalcocite and chalcopy-rite, etc., are reduced to a certain extremely fine state of comminution they are definitely beyond the reach of separation upon any of the concentrating devices then known. By using drag-belt classifiers (which served as conveyors as well as separators), the overflow ,would be of the usual "slimes" class. Experiment had shown that when these drag-belt overflows were properly diluted (that is, to about 5 to 7 per cent. solids in the feed under treatment) the very fine sand, and especially the very fine but still granular sulphide particles, would, if given a short distance to fall, quickly settle out in prime condition to yield an excellent recovery on vanners; a further valuable feature would be that the very fine non-separable final overflow tonnage might be discharged direct to tailing, thus conserving space requirements so as to permit within the old building, without embarrassment, the increase of capacity required. For reasons that are obvious, this kind of feed preparation for the slime could not be successfully accomplished in any form of pointed boxes or

Jan 1, 1917

By E. Houdremont, H. Schrader, H. Bennek

The different influences exerted by the various alloying elements in iron and iron-carbon alloys give rise to a great number of complexities, which are difficult to grasp. It is important therefore to study any systematic relations that may exist between the effects exerted by the various alloying elements, in order to obtain a general classification and thus a clearer conception of the nature of alloy steels. A systematic survey of the alloys of iron, based on an investigation of the binary equilibrium diagrams, was recently published by Wever. Although his work deals little with properties of importance in works practice, its purpose being rather to point out the theoretical agreement among the types of binary equilibrium diagrams and the position of the alloying elements in the periodic system (atomic radii, etc.), the classification proposed nevertheless also suggests relationships among the properties of the alloys in question, even though the alloys may contain carbon in addition to iron and the alloying element. Wever divided the alloys of iron into one group exhibiting an open or enlarged gamma field and another exhibiting a closed or restricted gamma field, with both groups capable of further subdivision depending upon whether a continuous series of solid solutions is formed, or, owing to the separation of compounds, etc., only a limited series. Thus all alloying elements which with iron form a closed gamma field, a "gamma loop," produce alloys that beyond the composition corresponding to the greatest extent of the gamma loop are composed of ferrite alone at all temperatures. Alloys of this composition accordingly are not susceptible to ordinary heat treatment because of the lack of transformations. Steels of this class may thus be divided into steels that contain less than the critical amount of alloying element, and are subject to heat treatment, and those that contain more than the critical amount of alloying element and are not subject to heat treatment. Thus chro-

Jan 1, 1935

By H. Schrader, E. Houdremont, H. Bennek

The different influences exerted by the various alloying elements in iron and iron-carbon alloys give rise to a great number of complexities, which are difficult to grasp. It is important therefore to study any systematic relations that may exist between the effects exerted by the various alloying elements, in order to obtain a general classification and thus a clearer conception of the nature of alloy steels. A systematic survey of the alloys of iron, based on an investigation of the binary equilibrium diagrams, was recently published by Wever. Although his work deals little with properties of importance in works practice, its purpose being rather to point out the theoretical agreement among the types of binary equilibrium diagrams and the position of the alloying elements in the periodic system (atomic radii, etc.), the classification proposed nevertheless also suggests relationships among the properties of the alloys in question, even though the alloys may contain carbon in addition to iron and the alloying element. Wever divided the alloys of iron into one group exhibiting an open or enlarged gamma field and another exhibiting a closed or restricted gamma field, with both groups capable of further subdivision depending upon whether a continuous series of solid solutions is formed, or, owing to the separation of compounds, etc., only a limited series. Thus all alloying elements which with iron form a closed gamma field, a "gamma loop," produce alloys that beyond the composition corresponding to the greatest extent of the gamma loop are composed of ferrite alone at all temperatures. Alloys of this composition accordingly are not susceptible to ordinary heat treatment because of the lack of transformations. Steels of this class may thus be divided into steels that contain less than the critical amount of alloying element, and are subject to heat treatment, and those that contain more than the critical amount of alloying element and are not subject to heat treatment. Thus chro-

Jan 1, 1935

By A. C. Dorenfeld

Ores of the Mammoth mining district, some 45 miles northeast of Tucson, Arizona, are treated by Mammoth-St. Anthony, Ltd. The ores now treated come from a complex system of veins and faults, comprising three mines, in close proximity: The Mohawk, Mammoth and Collins. The ore treated in the past was oxide ore, which contains economic amounts of gold, silver, lead, molybdenum, and vanadium (as wulfenite and vanadanite). The lead-zinc sulphide ore has never been treated before. The Ore The sulphide ore contains galena, sphalerite, marmatite, pyrite and some chal-copyrite, covellite, chalcocite and bornite, as well as small amounts of gold and silver. The value of the ore is principally in the lead and zinc content. The lead-zinc sulphides are substantially liberated at a minus 65-mesh grind. However, a large part of the chalcopyrite and other copper minerals is not freed, but remains as pin points on the sphalerite. Economically, the copper is unimportant. The gangue is a rhyolite granite, with very little limestone. There is no molybdenum or vanadikm in the sulphide ore. History of Sulphide Treatment Test work on samples of the sulphide ore was conducted by several equipment companies, the Arizona Bureau of Mines and the company's laboratory. Results of this test work indicated that for some reason, which at the time could not be explained, recoveries would be only about 65 per cent lead and 50 per cent zinc. Notwithstanding this, because of the nation's need for metals, the management built a 150-ton treatment plant. The mill was started in June 1942. During December 1942, using the standard method of treating lead-zinc ore, the monthly results were as shown in Table I. These results were poor. Too much lead was in the zinc concentrate, and too much zinc in the lead concentrate. It should be noted here. that prior to December attempts were made to depress the sphalerite with large and varied amounts of cyanide, zinc sulphate, and sodium sulphite with poor results.

Jan 1, 1947