Search Documents

By A. M. Khan, I. Fatt

A new type of steady-state thermal conductivity apparatus is presented and described. Results of measurements on Berea sandstone, Solehofen limestone, Bandera sandstone and Bakelite are presented. The measurements were made in a two-hour period at temperatures up to 80C and axial stress to 125 bars. Results show that the thermoelectric heat pump and tbermistor-controlled electric heater can be used in a steady-state apparatus for measuring thermal conductivity of mck. Steady-state is reached within two hours. With Urethane foam insulation, not more than 3 per cent of heat is lost by radial flaw. The apparatus can be used as a comparator or for absolute thermal conductivity determinations. INTRODUCTION Calculations of heat flow through the earth, both for scientific purposes and engineering design, require thermal-conductivity data on rock. However, the high variability of rock often makes handbook thermal-conductivity data of little value. For engineering purposes in particular, it is desirable to have measured data on samples of the rock mass under study. Laboratory methods for measuring thermal conductivity of rock use either time-dependent1-3 or steady - state temperatures .4,5 The time -dependent (transient) techniques give thermal diffusivity from which thermal conductivity can be calculated if the specific heat and density of the sample is known. Most transient techniques require lengthy and involved sample preparation. Also, the accuracy tends to be low. Steady-state techniques are more exact and are the most commonly used. The steady-state methods, however, also have their difficulties. A long time is often required to reach steady state, troubles have been encountered in establishing good thermal contact between the heating and cooling elements and the rock sample, and unaccounted-for heat losses are difficult to prevent. In this paper we present a description of a new type of steady-state thermal conductivity apparatus. With it, measurements have been made in two hours at temperatures up to 80C and axial stress to 125 bars. Sample preparation is simple and no thermal conductivity standard is needed.6 APPARATUS Our steady-state apparatus is an improvement . over the conduction pile used by Zierfuss and van der vliet4 and Somerton.5 A linear heat flux is established through a conduction pile consisting of the rock sample and a standard material of known thermal conductivity in series. The thermal conductivity of the sample is calculated from the ratio of the temperature drop across the sample

Jan 1, 1966

By L. E. Shiffman

W. J. Parton—Those operators faced with the problem of treating fine coal whether in bituminous or anthracite will find this paper most timely. I would like to take this opportunity of discussing Mr. Schiffman's paper and at the same time express certain views relating to our Tamaqua plant. I would like to ask the author what type of impeller and diffuser is used in the Denver cells? Screen analysis of products from individual cells indicate that coarser material resists flotation and only floats after greater retention time in the last few cells. Also, the need for a scavenger screen to reclaim non-floated coal particles further stresses this point. I have always felt that more efficient means of cleaning coal between 10-mesh and 28-mesh existed than flotation. Reagent and power costs are high for the flotation process. When floating +28-mesh particles, cell capacity is lowered and some of the particles are lost with the refuse. The Tamaqua plant of the Lehigh Navigation Coal Co. floats —28-mesh coal and capacity of recoverable coal is 40 tph for 1800 cu ft of Denver cells; or 0.05 tons per cu ft of cell. At Kimberly 7.75 tph for 600 cu ft of cell gives 0.013 ton per cu ft of cell. At Bessie 14 tph for 800 cu ft of cell gives 0.017 tons per cu ft of cell. It would be appreciated if the author would comment on what he feels is the upper size limit of particle to attain most efficient utilization of the flotation process. The dewatering screw is a very interesting development since it offers a simple way to prepare coal sludge for more complete clewatering by drainage or mechanical dewatering on screen or filters. In other words it could be used to accomplish the same thing as a thickener tank. I would appreciate having the author's comment on how he thinks such a screw dewaterer would work on a froth.* The process as used in floating coal at the Bessie and Kimberly plants may be referred to as more of a bulk oil float in contrast to a froth flotation process. Experiments on increasing capacity of cells is most interesting since we are going through such an experi- mental period at the present time. Recently a double overflow was installed on our No. 30 Denver cells. So far results are not conclusive. In reviewing this paper the following comments are made pertaining to investigation of methods for increasing capacity: Supercharging: Supercharged air in matte flotation or for that matter the use of the normal amount of air drawn in by the impeller would in all probability cause such an aeration in the cell as to destroy the buoyant effect given to the coal particles by the excessive amount of kerosine used. In other words, air creates an agitation zone throughout the cell, creating a boiling and thereby giving a lower recovery in the cell. It would be interesting to know whether the 7 pct increase in recovery was with no air being admitted to the stand pipe. Changing Impeller Speed: The speed of a receded disc impeller for a No. 30 cell as recommended by the Denver Equipment Co. is, I believe, approximately 250 rpm. At this speed and using supercharged air in excess of 8-oz pressure, we have observed a boiling action in the cells. In our flotation we endeavor to obtain some degree of froth flotation using pine oil as a frother. The boiling action as caused by increasing the amount of air added to the cells is detrimental to recovery in froth flotation. It is our belief that to obtain increased recovery from a cell in froth flotation, additional air must be introduced but at the same time this air must be dispersed throughout the pulp in the form of small bubbles and this can only be done by increasing the speed of the impeller. Therefore, if Mr. Schiffman decreased the speed of the No. 30 impellers and at the same time continued to use supercharged air, the boiling action may have been increased because larger bubbles developed. The lower recovery as reported could be due to this factor. Decreasing the impeller speed will definitely decrease the power consumed but may have other disadvantages. First, we believe it will permit "sanding" in the cell and this in our opinion will increase the wear on the impeller and diffuser, especially so, if there is pyrite and/or sand present in the feed. "Sanding" in the cell when air is used, as in froth flotation, will effect the dispersion of this air and cause boiling.

Jan 1, 1951

By L. E. Shiffman

W. J. Parton—Those operators faced with the problem of treating fine coal whether in bituminous or anthracite will find this paper most timely. I would like to take this opportunity of discussing Mr. Schiffman's paper and at the same time express certain views relating to our Tamaqua plant. I would like to ask the author what type of impeller and diffuser is used in the Denver cells? Screen analysis of products from individual cells indicate that coarser material resists flotation and only floats after greater retention time in the last few cells. Also, the need for a scavenger screen to reclaim non-floated coal particles further stresses this point. I have always felt that more efficient means of cleaning coal between 10-mesh and 28-mesh existed than flotation. Reagent and power costs are high for the flotation process. When floating +28-mesh particles, cell capacity is lowered and some of the particles are lost with the refuse. The Tamaqua plant of the Lehigh Navigation Coal Co. floats —28-mesh coal and capacity of recoverable coal is 40 tph for 1800 cu ft of Denver cells; or 0.05 tons per cu ft of cell. At Kimberly 7.75 tph for 600 cu ft of cell gives 0.013 ton per cu ft of cell. At Bessie 14 tph for 800 cu ft of cell gives 0.017 tons per cu ft of cell. It would be appreciated if the author would comment on what he feels is the upper size limit of particle to attain most efficient utilization of the flotation process. The dewatering screw is a very interesting development since it offers a simple way to prepare coal sludge for more complete clewatering by drainage or mechanical dewatering on screen or filters. In other words it could be used to accomplish the same thing as a thickener tank. I would appreciate having the author's comment on how he thinks such a screw dewaterer would work on a froth.* The process as used in floating coal at the Bessie and Kimberly plants may be referred to as more of a bulk oil float in contrast to a froth flotation process. Experiments on increasing capacity of cells is most interesting since we are going through such an experi- mental period at the present time. Recently a double overflow was installed on our No. 30 Denver cells. So far results are not conclusive. In reviewing this paper the following comments are made pertaining to investigation of methods for increasing capacity: Supercharging: Supercharged air in matte flotation or for that matter the use of the normal amount of air drawn in by the impeller would in all probability cause such an aeration in the cell as to destroy the buoyant effect given to the coal particles by the excessive amount of kerosine used. In other words, air creates an agitation zone throughout the cell, creating a boiling and thereby giving a lower recovery in the cell. It would be interesting to know whether the 7 pct increase in recovery was with no air being admitted to the stand pipe. Changing Impeller Speed: The speed of a receded disc impeller for a No. 30 cell as recommended by the Denver Equipment Co. is, I believe, approximately 250 rpm. At this speed and using supercharged air in excess of 8-oz pressure, we have observed a boiling action in the cells. In our flotation we endeavor to obtain some degree of froth flotation using pine oil as a frother. The boiling action as caused by increasing the amount of air added to the cells is detrimental to recovery in froth flotation. It is our belief that to obtain increased recovery from a cell in froth flotation, additional air must be introduced but at the same time this air must be dispersed throughout the pulp in the form of small bubbles and this can only be done by increasing the speed of the impeller. Therefore, if Mr. Schiffman decreased the speed of the No. 30 impellers and at the same time continued to use supercharged air, the boiling action may have been increased because larger bubbles developed. The lower recovery as reported could be due to this factor. Decreasing the impeller speed will definitely decrease the power consumed but may have other disadvantages. First, we believe it will permit "sanding" in the cell and this in our opinion will increase the wear on the impeller and diffuser, especially so, if there is pyrite and/or sand present in the feed. "Sanding" in the cell when air is used, as in froth flotation, will effect the dispersion of this air and cause boiling.

Jan 1, 1951

By D. N. Dietz

Jan 1, 1969

By R. W. Bartlett

DISILICIDE coatings, MeSi2, on refractory metals are usually grown by a solid-state diffusion reaction similar to the parabolic oxidation of metals. Two or more silicide compounds occur in each of the binary silicon-refractory metal systems. When an adequate source of silicon is available during the coating process, the lower silicide compounds are usually not formed.1 However, during service application of the coated refractory metal, continued heating causes further diffusion and growth of the lower silicides. A study of the growth kinetics of the lower silicides in the molybdenum and tungsten binary systems with silicon was previously reported.2 The present study is concerned with the growth kinetics of Ta5Si3 and Cb5Si3, formed as conjugate layers between TaSi2/Ta and CbSi2/Cb diffusion couples, respectively. Diffusion couples consisting of disilicide-coated tantalum and columbium sheet coupons were subjected to diffusion heat treatments, cross-sectioned, and scanned by an electron-microprobe analyzer to determine the relative X-ray intensity profiles. These profiles correspond closely to concentration profiles for the constituents, and were used to identify phases and locate phase boundaries. The analysis of a single specimen after a diffusion-anneal provides only one value for the Me5Si3 phase thickness, corresponding to the time and temperature of the diffusion treatment. Consequently, each isothermal curve showing the rate of accumulation or depletion of silicide phases required several samples with identical diffusion temperatures but different diffusion times. The disilicide coatings were prepared by pyrolizing commercially pure silane in a hydrogen carrier gas. The hydrogen was purified by passage through a palladium membrane. Commercially pure tantalum and columbium sheet metal coupons, 0.005 by $ by 2 in., were used. All of the coated specimens for each system were prepared together in a single group in order to minimize coating variations among individual specimens. During pyrolysis, the brightness temperature was maintained at 1200°C. With suitable flow rates at this temperature, only the disilicides of tantalum and columbium were formed in detectable amounts. Coated specimens were subjected to diffusion an-neals in a tube furnace with automatic proportional control within ±10°C. A H2-Ar mixture, deoxidized and dried over anhydrous magnesium perchlorate, was used to prevent oxidation during the diffusion anneal. Diffusion couples were cross-sectioned, polished and examined with an A.R.L. electron-microprobe X-ray analyzer. Both metal constituents in each specimen were simultaneously scanned using a 1-p beam spot size and either 1- or 2-µ steps. Analyses were performed using the Ka radiation of columbium and silicon, and the La, radiation of tantalum. For all specimens, an acceleration voltage of 30 kv was used, and integration was made against the specimen current. LiF and A DP monochrometers were used to isolate characteristic radiations. Three or more traverses were made on each specimen. The intensity scales were adjusted using the constituent metals and standard samples of the silicide compounds which had been verified by X-ray diffraction. The relative intensity profiles were used directly, in conjunction with the standard samples, to identify compounds and phase boundaries. The stoichiometries differ considerably between the silicide compounds in both systems, and the homogeneity range for these silicide compounds is narrow. These characteristics result in marked differences in relative intensities of the fluorescing elements—differences which permit ready identification of phases and phase boundaries. Projections of both electron back-scattered images and characteristic

Jan 1, 1967

By Benjamin Gi ldersleeve

Uniquely colored, thin-bedded quartzite is quarried between Crossville and Crab Orchard in Cumberland County, Tenn. It is produced in all sizes up to the limits of transportation from beds usually ranging in thickness from less than 1/2 in. to 6 in. The stone is very resistant to wear and weathering and is marketed throughout the country for many different purposes in exterior and interior construction. The annual production exceeds 36,000 tons, valued at nearly $1,000,000.

Jan 1, 1950

By H. Jehn

Like some other Pt-group metals palladium shows a low but considerable solid solubility of oxygen, which was found already from oxidation studies. The oxygen solid solubility of palladium in equilibrium with gaseous oxygen has been investigated at 900 - 1300 °C in oxygen (665 mbar) and air by gassing and analyzing polycrystalline samples. The 0-concentrations range from 40 to 90 ppm and decrease with rising temperature. The isobaric solubility can be represented by the least-squares fit log c0 = 0.5 log p02- 0.32 + 920/T (c0 in wt. ppm, p02 in mbar, T in K). The thermodynamic data of the exothermic solution reaction are calculated to ?H°= -17.6 kJ?mol-1 and ?S° -76.5 J?mol ? K-1. The behaviour of palladium in an oxygen atmosphere is characterized by the simultaneous reactions of the solution of oxygen in the metal and the formation and evaporation of volatile oxides besides the pure metal evaporation.

Jan 1, 1984

By S. Dinda

A series of as -quenched 4340 bars were drawn through a carbide die to various reductions. The X-ray diffraction technique of Lopata and Kula was employed to detect preferred orientation in drawn martensitic steel bars with low amounts of deformation, as lord as 0.8 pct The specimen face of each bar examined was cut at a 45-deg angle to the bar axis. The reflecting planes in the 45-deg face were varied by appropriate rotation of the sample using a spectrogonionzeter. TIE X-ray bean of a diffractometer was reflected from the center of the bar and the diffracted intensity was delected with a proportional counter and recorded. Intensity peaks were developed by cold working for 110 planes oriented at 0 and 60 deg to the bar axis. The intensity peaks increased with increasing defortnalion us a preferred orientation with a 110 texture developed parallel to the drawing direction. The intensity peaks for deformed as-quenched specimens remain unchanged after tempering at temperatures as high as 1000°F. The same amount of preferred orienlalion was observed both inferritic (hot-rolled) and martensitic (as-quenched) structures after an equivalent amount of deformation. THE deformation of martensite with medium carbon content. less than 0.5 pct, has been studied by Breyer et a1.1,2 It was reported that changes in properties such as resistivity, carbide precipitation, and the introduction of a yield point phenomenon were produced after cold reduction of as-quenched AISI 4340 steel bars. Later, Breyer and Nachtman3 studied the effect of cold reduction upon X-ray line intensity. They showed that the integrated 110 line intensity increased with increasing deformation when the planes examined were perpendicular to the die drawing direction. The integrated 110 line intensity for planes oriented at 45 deg to the die drawing direction, in contrast, were found to slightly decrease. These changes were proposed to be consistent with the previously proposed model of a stress-induced ordering of carbon atoms in the vicinity of dislocations.1,2 Objections can be raised to the above interpretation of the X-ray results on two grounds: a) Rough structure factor calculations indicate that the intensity changes are too large (50 pct observed vs 2 pct calculated4,5) to be the result of changes in the location of iron atoms produced by the stress-induced ordering of the carbon atoms. b) The results might be explained in terms of preferred orientations, although X-ray evidence of the development of texture has not been reported in the literature for deformations as slight as 1 or 2 pct. The aim of the present work was to determine if preferred orientation was present in such cold-drawn martensitic steel bars. In drawn rod or wire there is generally a certain crystallographic direction which is aligned in the direction of the wire axis, and the crystallographic planes are distributed symmetrically around this "fiber axis".6-8 This type of cylindrical specimen, with the fiber axis located at the center, will show rotational symmetry. Lopata and Kula9 proposed an experimental method utilizing a specimen cut at 45 deg, see Fig. 1. The X-ray beam is diffracted from the center of this bar cross section. The specimen is rotated around an axis perpendicular to the bar axis and lying in the 45-deg cut face. This permits the angle between the normals to the reflecting planes and the bar axis to be varied from 0 to 90 deg.9 With this arrangement the errors due to absorption and irradiated volume compensate each other.' This greatly simplifies analysis of the data and is of considerable advantage for quantitative measurements. If there is preferred orientation in the specimen, more planes are oriented in a particular direction in the bar. When the bar is rotated to the favorable Bragg condition for that particular orientation, the intensity will be higher than that for some other angle. This technique was adopted for the present investigation.

Jan 1, 1969

By Edward H. Bzirdick

THE territory under particular consideration in this article comprises portions of La Plata and Montezuma Counties, situated in the southwestern corner of Colorado, and around the base of the La Plata Mountains. (See Fig. 1.) In southeastern Utah and northeastern Arizona there are several mountain systems whose origin and structure are practically identical with the La Platas so that ore occurrences found in the latter can be hopefully looked for in the former. With this assumption, there is an area around the laccolithic ranges which offers promise for a successful exploration for gold ores. Ore occurrences of the Silverton, Telluride, Rico, or Ouray Districts will not be discussed, although in these areas the Mesozoic sediments are more or less involved within the ore-bearing complex. These have been intensively studied and developed. The idea is to set forth what my mining experience has been within the largely unaltered . Mesozoic horizon which remains around the extreme bases of the La Plazas. This, until recent years, has been almost entirely neglected by prospectors and operators and, so far as similar territory in Utah and Arizona is concerned, so remains.

Jan 1, 1934

By H. E. Hawkes, D. A. Barr

Time variations in the copper content of the sediments of streams draining mineralized areas were studied in two areas of contrasting climatic environment, one in northern and one in southern British Columbia. In each area, samples were collected and observations made of rainfall, stream discharge and air and water temperature at intervals throughout the summer season. Samples were analyzed for total and cold-extractable copper. Results showed a weak inverse relation between cold-extractable copper and discharge in two out of the three test sites in the southern area, and a decrease in ratio of COld-extractable to total copper over the duration of the test period at a highly anomalous site in the northern area. In suspended rock flour resulting from glacial erosion of mineralized rock in the northern area, virtually all the copper was found to be soluble in cold, dilute hydrochloric acid. None of the variations observed is sufficient to cause serious problems in geochemical sediment surveys. Systematic collection and trace analysis of stream sediments has seen wide application in recent years as a method of primary prospecting in primitive areas. Common practice is to collect fine-grained samples of sediment either from the active channel or from the flood plain near the channel. Samples are dried, sieved and the -80-mesh fraction analyzed after breakdown of the sample by a relatively strong attack, such as by fusion or by treatment with hot perchloric acid. Drying, sieving and rigorous chemical attack requires established facilities, either in a well equipped central laboratory or in base camp. Thus analysis for total metal involves a substantial delay from the time the samples are collected until the analytical data can be reported. An alternative system uses a cold aqueous extrac-tant in place of the hot acid or flux.4 Advantages of the cold-extraction techniques are that kits can be prepared for use directly at the sample site and that, in some problems, the patterns in cold-extractable metal, usually abbreviated cxMe, are more useful as ore guides than the patterns in total metal.' In the course of operational geochemical sediment surveys, a problem that has come up repeatedly is failure to reproduce anomalous values or patterns by resampling the same areas. The mystery of the vanishing anomaly has led to speculation as to whether there is a significant variation in the metal content of sediment samples with the weather or with the time of year. Review of the published literature shows that a number of experiments have been carried out on time variations in the metal content of stream water.1,2,5,7-9 The only published report on time variations in stream sediments that has come to the authors' attention, however, is by Govett,3 working in Northern Rhodesia.

Jan 1, 1963

By Robert P. Koenig

FOR the first time other than on occasion of war the people of the United States are experiencing full-scale participation in world affairs. Public concern has seldom been so involved with conditions and events beyond our own continental limits. Our interest is not wholly of recent origin. Over the years the activity of the United States as a world power and an important trading nation brought about the widening of our political interests and the progressive interrelation of our economy with that of the rest of the world. Some may see in our present phase of world-wide activity the natural consequence of our continued growth. Such observers must also be aware that within recent years our importance in world affairs has been considerably increased. For within the space of an extremely short period events have occurred that have literally jet-propelled the United States into the role of a leading participant in the conduct of world affairs. Little of the choice of this role was left to us. The decline of power in western Europe, the ascendancy between the Elbe and the Pacific shore of an obviously antagonistic force, our earnest endeavor to secure international control of atomic energy, the necessity of providing relief and rehabilitation to war-ravaged areas, and the police work that must be done in occupied territories are problems which have risen in great measure without our help-but they cannot be solved without it.

Jan 1, 1948

By JOHN JERMAIN

In my opinion, the explanation of the fuel-requirements involving the conception of heat available and necessary above a critical temperature, as advanced by Johnson 1 and elaborated by Howe, Raymond and others,2 affords a theoretically correct basis for such an accounting. It is the purpose of this paper to set forth a first crude attempt to construct a formula which shall show quantitatively the relation between the various factors affecting fuel-economy, and afford a means of comparing the enormous amount of data on the fuel-consumption of various blast-furnaces, at various times and under various conditions of operation. I have also applied this formula to a large number. of individual cases, and have, by its means, compared the furnace-practice of several important iron-making districts. II. DERIVATION OF FORMULA FOR FUEL-REQUIREMENTS. The general expression for the fuel-requirements of the blast-furnace, which I believe to be theoretically correct as to form, is as follows Carbon per ton of iron = Heat per ton of iron necessary in hearth above Tc./Heat per pound of carbon available in hearth above Tc. XFactor of rate of driving. +Carbon dissolved by CO2 of flux. +Carbon dissolved incidental to reduction of ore. + Carbon dissolved in pig-iron. (NOTE.-Tc = critical temperature.) Since, according to Johnson's theory, fuel-economy is usually limited by heat available and necessary in the hearth, rather than by the total heat supplied and necessary, we may write Carbon needed in hearth = Hn/Ha in which Hn is the heat per ton of iron necessary in the hearth above some critical temperature, and Ha is the heat per pound of carbon available in the hearth above this same critical tem¬perature. 1 Trans., xxxvi., 454 (1906). 2 Trans, xxxvi., 792 to 798 (1906) ; Trans, xxxvii., 216 to 237 (1907).

May 1, 1911

By Krahmann, Rudolf

THE following is an account of a survey undertaken to test the possibility of outlining a kimberlite pipe by magnetouietric methods. Kimberlite is a basic igneous rock closely related to melilite-basalt or alnoite, which occurs either in the form of volcanic plugs or as dikes intruded into rocks of various types and geological ages up to and includ¬ing the Lower Cretaceous. The famous diamond mines of South Africa are all in kimberlite pipes and these pipes are probably the original source as well of the vast alluvial deposits found in various parts of the country. The pipe chosen for this experiment is one that ' occurs on the farm Goedgevonden No. 20, about sixteen miles north of the village of Klerksdorp and ninety miles southwest of Johannesburg. Some prospecting has been done on this pipe and diamonds were produced from it but not in paying quantities. The magnetometric survey was made in June, 1932, by R. Krahmann and H. Wallisch and the results are shown on the accompanying plan. On the plan are shown also the boundaries of the pipe as exposed at the surface and details in regard to the surrounding foundations. These are taken from a geological survey made at a later date by W. Beetz, of Johannesburg.

Jan 1, 1935

By AIME AIME

THE program of government drilling, conducted jointly by the U. S. Geological Survey and the Bureau of Mines, has demonstrated the presence in Texas and New Mexico of potash-bearing beds of considerable importance. Information regarding the ex- tent and location of the potash deposits as presented at the non-metallic sessions was of great interest to many engineers. These subjects will be covered in greater detail in later paragraphs. The first session, with about 50 in attendance, convened at 10 a.m. on Feb. 18, with Oliver Bowles, chair- man of the Committee on Non-Metallic Minerals, pre- siding. The first paper was on "Soapstone Mining In Virginia," presented by C. W. Ryan of Lynchburg, Va. The nature and extent of the soapstone deposits of Nelson County were described in some detail. In origin, the soapstone is undoubtedly related to a basic peridotite rock though its mode of formation is some- what uncertain. This main soapstone deposit occurs in three veins, the western, middle, and eastern, the middle vein being of greatest economic importance. Methods of stripping, quarrying and milling the rock were described and the uses of soapstone were enum- erated. In discussing this paper, C. P. Berkey, of Co- lumbia University strongly favored the theory of igneous origin of the soapstone and the need for further detailed geological study. J. L. Gillson of Cambridge, Mass., stated that the Vermont and New York talc deposits were always associated with characteristic minerals, such as, a chlorite of one particular variety, siderite, amphibole, magnetite, and biotite. C. H. Behre of Cincinnati, Ohio, raised the question of parallelism in the soapstone structure and Mr. Ryan stated that such parallelism was in evidence in some parts of the deposits. H. A. Wheeler of St. Louis, Mo., also took 'part in the discussion.

Jan 1, 1929

By AIME AIME

NAPOLEON'S dictum that an Army travels on its stomach has not changed in this present war, but the things an Army's stomach calls for would be more than strange to Napoleon. Today one of the main articles of diet for the mechanized army is oil and gasoline, and the chief and most efficient source of 'apply overland is the pipe line. It was a flexible 4-in. pipe line that supplied the voracious appetite of tanks, trucks, jeeps, and planes across the North African desert. and it is the 1800-mile pipe line from Calcutta to Kunming, Yunnan Province in China, the longest in the world, that supplied oil and 100-octane gas for the trucks, tanks, Jeeps, and planes fighting on the Assam-Burma-China front in recent months. Completion of this approximately 1800-mile pipe line to China over rivers that had never been bridged, over hill that towered 9000 ft., and over swamps

Jan 1, 1945

[RALPH ADAIR Ore Dressing Consultant Bull Mtn. Rd., Asheville, N. C. Phone 4-1693 JAMES A. BARR Consulting Engineer Mt. Pleasant, Tennessee Washington, D.C. BEHRE DOLBEAR & COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4. N. Y. I. R. BERENT Engineering Consultants and Contractors Mineral Exploration, Mine Evaluation, Mine Designs and Mine Management 156, Ataturk Bulvarl-Ankara, Turkey BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 210 La Arcade Bids. Santa Barbara, Calif.]

Jan 1, 1952

[RALPH ADAIR Ore Dressing Consultant Bull Mtn. Rd., Asheville, N. C. Phone 4-1893 JAMES A. BARR Consulting Engineer Mt. Pleasant, Tennessee Washington, D.C. BEHRE DOLBEAR & COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4, N. Y. I. R. BERENT Engineering Consultants and Contractors Mineral Exploration, Mine Evaluation, Mine Designs and Mine Management ` 188, Ataturk Bulvari-Ankara, Turkey BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 8 Haward-Canfleld Bldg. Santa Barbara, Calif.]

Jan 1, 1952

[RALPH ADAIR Ore Dressing Consultant Bull Mtn. Rd., Asheville, N. C. Phone 4-1693 JAMES A. BARR Consulting Engineer Mt. Pleasant, Tennessee Washington, D.C. BEHRE DOLBEAR & COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4, N. Y. I. R. BERENT Engineering Consultants and Contractors Mineral Exploration, Mine Evaluation, Mine Designs, and Mine Management 156, Ataturk Bulvari-Ankara, Turkey BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 210 La Arcada Bldg. Santa Barbara, Calif.]

Jan 1, 1952

By Donald H. McLaughlin

ZEST in the search for new supplies of metallic ores and petroleum is difficult to maintain with stocks of raw materials accumulating and with over- production rightly or wrongly blamed for most of our industrial troubles. Enthusiasm over new methods of prospecting has consequently diminished and exploration programs in many fields have been drastically cur- tailed. Very naturally the effects have been felt with particular keeness in highly specialized phases of the work, such as geophysical prospecting, for the feverish scramble for new areas in which to drill beneath magnetic or electrical anomalies has abated, and there is even a lull in the firing in the battle over salt domes on the Gulf Coast. It is unquestionably an unhappy time for many of the organizations dependent on this work, but in certain respects the situation may be beneficial in correcting unsound practices that .have grown up through the necessity for haste and for quick decisions. With the restriction of the field to the more competent workers by the harsh rule of survival of the fittest, a general improvement, not only in technique but in business methods, can be expected which may go far in restoring public confidence. Geophysical prospecting in the short period that it has been utilized in North America, has suffered severely both from over-popularity and from excessive abuse. The former evil now

Jan 1, 1931

By B. VISWANATH

T HE Mysore iron works, at Bhadravati, about 2000 ft. above sea level in the Shimoga district of Mysore, British India, is served by a meter gage branch line of the Mysore State Railways. The works which were designed and erected by Perin & Marshall, who still act as consulting engineers, are surrounded by a thickly wooded country which sup- plies about 400 tons per day of wood for fuel. The ore deposits lie 20 miles to the south, and limestone quarries are close by the works. The Bhadra river sup- plies the works and the town with the necessary quantity of water. Dwelling houses for the employees

Jan 1, 1930