Search Documents

By P. F. Kinyoun

MANY interesting new features are embodied in the latest extension to the open-hearth department of the Bethlehem Steel Co., at Lackawanna, N. Y. Automatic control of the important factors in furnace operation-fuel, air, draft, pressure, slag composition, and of the temperature in various regions of the furnace-has been carried out to a remarkable degree; the human factor is minimized, and the chances for mishaps and irregularities in operation are greatly reduced.

Jan 1, 1937

air-lift and equipped with tapered tubing of proper design, we would have a gas input consumption of about 2500 cu. ft. per bbl., which at 3 to 4c. per 1000 cu. ft. would be 7 1/2 to l0c, per bbl., and there would be very infrequent loss of production due to stoppages. It has been demonstrated that with efficient design of air-gas lift, the production of wells can be increased much beyond that obtained with the former type of air-lift employed; also that small wells can be operated by air-lift with tapered tubing at a cost that places this method in competition with beam pumps in many fields. The next step in conservation that the writer expects to have an opportunity to demonstrate is that of restoring the pressure in a pool and producing by air-gas lift all of the oil possible to lift economically. This combined operation is probably the method toward which we shall eventually be working in recovering the maximum quantity of oil from pools where the oil is recovered through bore holes. General Discussion on the Air-gas Lift H. P. Porter, Tulsa, 0kla.—The papers presented at this meeting contain a great amount of valuable information. Wonderful progress has been shown in the development of air and gas-lifts. There has been nearly everything brought out that touches upon the subject. The real point that is lacking is exact knowledge of the velocity with in the flow column which will produce the best effect—that is the thing we must know more about. Velocity in Gas-lift Flow In other lines of industry the matter of velocity of fluids in pipe lines has been well analyzed and there are known laws by which to calculate velocity of flow; for instance, in irrigation work large pumps are designed with intake pipos to employ an intake velocity of 4 ft. per scc. By reduced cross-sect'ion the velocity is increased rapidly as it enters the pump and the discharge rate is at 12 ft. per src., which in turn is reduced in the discharge column to 4 ft. per sec. Crushed coal, grain and granular material is found to be best conveyed by air when a pneumatic conveyor is employed at 100 ft. per sec. As in the design of a pumping plant or a pneumatic conveyor, the velocity at the lower end of the column in the flowing well must be controlled within certain limits for best results. Mr. Griswold, I believe, stated that they had velocity as low as 15 it. per scc. and from that up to 78 ft. per sec. Mr. Pierce and Mr. Lewis showed an ideal flow column showing how the velocity increased as the fluid was carried up the column, hut did not give any figures as to the velocity. It would be well to take that sort of a diagram to establish an ideal velocity at the lower or intake end, and then calculate the velocity from expansion of the gas as it goes up. It may be that the, ideal intake velocity would vary, depending on the depth of the well, the quantity of liquid to be handled or the pressure which it may be desired to hold. The subject is one that might be worth much research.

Jan 1, 1928

By Henry A. Stiff, and Lawrence E. Davis

The authors previously presented a method for predicting the tendency of oil field waters to deposit calcium sulfate. The present paper gives a similar method for calcium carbonate. Methods for predicting calcium carbonate scaling tendencies in fresh waters have been available for some time, but these could not be used for brines. By experimentally deriving the value of the K term in the Langelier equation, a method has been developed which applies to waters of high salt content. A statistical study is included which shows that the experimentally derived values of K are in good agreement with actual conditions. Several applications of the final equation to production practice are given. INTRODUCTION The authors previously presented a method for predicting the formation of calcium sulfate scale in oil field waters.' Although calcium sulfate deposition is important in production operations, the majority of scale problems involve calcium carbonate. The present communication discusses a method by which the formation of this type of scale in oil field waters can be predicted. Calcium carbonate precipitation is caused by a shift toward carbonate in the carbonate-bicarbonate-carbon dioxide equilibrium. When equilibrium shifts in the other direction, the precipitate goes back into solution. Since there is usually considerable delay between the establishment of an equilibrium and the precipitation or solution of calcium carbonate, unstable conditions exist in which a water will precipitate or dissolve calcium carbonate on standing. Tillmans? who did a major part of the early work on carbonate scaling, pointed out that the condition of equilibrium not only indicates the tendency of a water to scale but also is an indication of its corrosive properties. Previously precipitated calcium carbonate combines with iron to form a dense crust which inhibits corrosion. If the water tends to dissolve carbonate, the scale becomes porous, and electrolytic corrosion takes place. Tillmans1 work was extended by several investigators until in 1934 Langeliers developed an equation setting forth the conditions of carbonate equilibrium. By the use of this equation the pH of a water at equilibrium can be calculated. If the actual pH is higher than the calculated pH, the water has a tendency to form scale. If it is lower. the water has a tendency to be corrosive. Langelier's equation can be expressed in a simple form as follows: SI = pH-pCa-pA lk-K where: SI is the stability index. A positive index indicates scale formation. A negative index indicates corrosion. pH is the pH of the water sample, as actually determined. pCa is the negative logarithm of the calcium concentration. pAlk is the negative logarithm of the total alkalinity. K is a constant, the value of which depends on the total salt concentration and the temperature. This equation has been shown to apply to waters with totaI solid concentrations as high as 4.000 ppm. In fact, control of fresh water treatment by means of this equation has been standard text-book practice for a number of years. Nomographs have been worked out so that the stability index of a fresh water sample can be determined in a matter of minutes. Most oil field waters, however, contain well over 4,000 ppm of salts and for this reason the usual application of Langelier's equation can not be made. By an empirical method we have extended the application of the Langelier equation to waters of high salt concentration. By the use of this equation the tendency of oil field waters to deposit calcium carbonate can be predicted.

Jan 1, 1952

By E. A. Elevatorski

Wollastonite, named after William H. Wollaston, an English chemist, is a calcium metasilicate, CaSiO3. It has a short history as an industrial mineral. The earliest production of wollastonite is reported to be from a deposit near Code Siding, located north of Randsburg, Calif. At this locality small tonnages of wollastonite were quarried during 1933-34 and 1938-41, and processed into mineral wool. This operation was largely experimental and virtually no United States production was again reported until the 1950s when a large deposit near Willsboro, N.Y., was developed by the Cabot Corp. A processing plant was placed on-stream in 1953, with nearly continuous production to date, and it is currently operated by Interpace Corp. Since 1958, wollastonite deposits in the Little and Big Maria Mountains of Riverside County, and in the Panamint Range of Inyo County, both in California, have operated intermittently for production of both ornamental and commercial wollastonite. During 1973, the United States was the major producing country, furnishing about 75% of the world's output. Recent production also has come from Finland, Mexico, and Kenya. Small amounts have been shipped intermittently from India, USSR, New Zealand, Republic of the Sudan, Republic of South Africa, and South-West Africa. The principal use of wollastonite is in the manufacture of ceramics, especially wall and floor tiles. Other uses are for paints, fillers, adhesives, reinforcing agents, plastics, fluxes, and glazes. Mineralogy Pure wollastonite, CaSiO3, has the composi¬tion of 48.3 % CaO and 51.7 % SiO,. However, it is seldom found in the pure state due to the ease with which it takes into solution the metasilicates of manganese, magnesium, iron, and strontium. Predominantly, wollastonite occurs as a contact metamorphic deposit forming between limestones and igneous rocks. Commonly associated minerals are garnet, diopside, epidote, calcite, and quartz. It has a specific gravity of 2.8 to 3.0, and hardness of 4.5 to 5 on Mobs' scale. When pure, it has a brilliant white color, but with impurities it may be grayish or brownish. Luster is vitreous to pearly. Melting point of wollastonite is about 1540° C. Wollastonite occurs in coarse-bladed masses, rarely showing good crystal form. It is usually acicular or fibrous, even in the smallest of particles. The most unique property of crushed and ground wollastonite is its cleavage. Fragments of crushed wollastonite tend to be needle-shaped, imparting a high strength, and this property is the basis for many of its uses. The fiber lengths are commonly in the ratio of 7 or 8 to 1, length to diameter. Some crystals of wollastonite fluoresce under short-wave or longwave ultraviolet light, or both; colors ranging from yellow-orange to pink-orange. Specimens may also show phosphorescence. The brightness of wollastonite is a property of considerable importance to the paint industry. Material, 99% pure, with a size of -325 mesh, has a General Electric reflectance rating of 92 to 96%. Chemically, wollastonite is inert and this property makes it useful as a filler and reinforcing agent. There are two polymorphs of calcium silicates: wollastonite, a low temperature form, and pseudowollastonite, a high temperature form. Inversion of wollastonite to pseudowollastonite occurs at about 1120° C, resulting in an increase in the coefficient of expansion and a color change. Pure white wollastonite, on inversion, may change to a cream tint, or various shades of red or brown. The color change is thought to be due to the presence of iron and strontium.

Jan 1, 1975

By Jei Y. Choi, Paul G. Shewmon

The surface self-diffusion coefficient of copper (D,) has been measured between 847° and 1069 "C for six different orientations. These were the(111), (110, (100, and three higher index surfaces. The activation energy for Ds (designated Q s) was found to be about 49 kcal per mol for all six surfaces, and Do about 2 x 104 sq cm per sec. At any temperature Ds varied by no more than a factor of three over these orientations. It is shown that, if the free energy of a surface atom is uniquely determined by its number of nearest neighbors, it follows from the Principle of microscopic reversibility that Qs should have the same value for all surface orientations, and Ds should vary little with orientation. This model also suggests that for clean fee metals Qs ~ 2/3 AH, (heat of vaporization). This is true for copper. ALTHOUGH it has been appreciated for several decades that atoms can diffuse more rapidly on a surface than through the bulk of a crystal, it has only been in the last few years that reliable values of the surface self-diffusion coefficient (Ds) have become available. Tracer studies of Ds had been attempted prior to this period, but when a tracer is placed on a surface, an ever increasing fraction of it is drained off into the lattice. The correction for this loss involves a very difficult, and as yet unperformed calculation. Those who have worked with tracers have not corrected for this loss.1, 2 Thus their results indicate that Ds is greater than the self-diffusion coefficient in the lattice (Dl), but it has not been established that they give quantitative data on Ds. A procedure which avoids the problem of tracer loss is to study the rate of mass-transfer under the effect of surface tension. If the surface asperity being studied is very small, the mass transfer occurs entirely by surface diffusion. The kinetics at which a grain boundary groove forms on an initially plane surface is a well-studied case of this type. The smoothing of a slight scratch in an otherwise flat surface is another procedure that has been studied. If these grooves are up to 20 to 30 µ in width, the dominant mechanism for mass transfer is surface diffusion (at least in the case of metals with low vapor pressures), and the widths can easily be measured with an interference microscope. Of these two, mass-transfer techniques only in the case of grain boundary grooving has a rigorous mathematical treatment been given. This was done by Mullins.3,4 His analysis predicted that in the case of copper in an atmosphere of an inert gas, surface diffusion should be the dominant transport mechanism. This analysis gave an equation for the groove profile and predicted that the width of the groove would increase as (time)1/4. Mullins and Shewmon showed that both of these predictions agreed with experiments.5 Thus the validity of the values of Ds given by this procedure seems to be well established. Gjostein has used copper bicrystals and the grain boundary grooving technique to determine Ds and the activation energy for surface selfdiffusion (9,) in the [001] direction on surfaces ranging between the (100) and (110) planes.= He reported that Qs = 41 kcal per mole and Do = 6.5 x 102 sq cm per sec for all orientations studied. Since the results did not change with the dew-point of the dry hydrogen atmosphere or the type of refractory tube used, he concluded that the surfaces were clean, or at least that the results were not influenced by any impurities chemisorbed from the atmosphere. The work reported here reproduces and extends Gjostein's study in that D s and Q s were determined for copper over a wider range of orientations. To study the effects of impurities, two purities of copper were used as well as cathodic etching to remove any possible electropolishing film. Gjostein postulated that the diffusing atoms on a surface near a low index plane are the few atoms which are adsorbed on the smooth region between ledges or steps in the surface. A more rigorous derivation of the equation relating Ds to the concentration and jump frequency of these adsorbed atoms is given here. Using this treatment, our empirical observation that Q s and D s are essentially the same for all surface orientations can be shown to follow from the assumption that the free energy of a surface atom is uniquely determined by its number of nearest neighbors. The studies of D s using the scratch technique have been carried out by Blakely and Mukura on nickel,' and by Geguzin and Oveharenko on copper. The latter study using copper gives values of D s roughly

Jan 1, 1962

By E. Lifshin, R. E. Hanneman

QUANTITATIVE applications of the electron micro-beam probe frequently involve the evaluation of complex mathematical expressions and/or the analysis of large amounts of experimental data. The purpose of this communication is to describe briefly a versatile and useful computer program system that is applicable to analyze rapidly a wide variety of practical microprobe problems. This system consists of a group of ten FORTRAN programs that can be stored on tape, cards, or in the memory disc of the computer. These programs, or links, can be run individually or in any prespecified sequence without interrupting the operation of the computer or without destroying information which is being transfered from one link to another. For the program system described here a GE-235 computer with disc storage was used, so that the DCHAIN method of program linking was employed. Included in the library are programs to: 1) initiate analysis of a new set of data and transfer control between all other programs in any predetermined manner; 2) generate theoretical calibration curves of composition vs relative intensity; 3) generate empirical deviation parameters from least-square fits of experimental calibration data from standards of known composition; 4) convert raw X-ray data to corrected composition; 5) determine inter diffusion coefficients by Matano analysis of con centrat ion -distance data on a uniaxial diffusion couple; 6) determine activation energies and frequency factors of temperature-activated processes such as diffusion; and 7) generate calibration curves for determination of the thickness of thin films using microanalysis. A detailed description of these computer programs and their underlying principles is available on request from the authors."' The first program to generate theoretical calibration curves of corrected relative intensities vs composition uses the Poole and Thomas atomic number correction' and the Philibert absorption factor' with a voltage-dependent mass absorption coefficient for electrons in the alloy. A modified Castaing fluores- cence correction is also used which includes the effects of both Ka and KO radiation and over voltage.' Once the theoretical curves have been calculated in 1 wt pct intervals, these results are least-squares fit to obtain Ziebold deviation parameters' which are stored in COMMON in the computer memory. The net discrepancies between the original theoretical calibration curve and the regenerated curve using the Ziebold parameter are computed. Although this link is explicitly written for K-K fluorescent interactions, it can be applied to K-L, L-K, and L-L interactions as previously disc~ssed."~ Similar programs have also been written to utilize the Wittry fluorescence correction, Birks combined corrections, and various other corrections.' These modified programs have proved to be quite useful for quantitative comparisons of the results of the various theories. The program for conversion of raw X-ray data to corrected composition includes corrections for drift, backround, and instrumental dead time. The corrected intensities are converted to composition by use of the Ziebold equation"2 and parameter obtained from the program system. The results can be obtained for either atom or weight fractions. In addition to accurately computing interdiffusion coefficients the Matano analysis program calculates least-square smoothed values of concentration, concentration gradient, and curvature for each point on the raw input concentration profile. In order to obtain high accuracies a unique method of performing a least-square polynomial fit to incrementally advancing profile segments which overlap is used.' This program has been successfully modified for use in ternary diffusion problems3 and can readily be modified to handle analysis of diffusion profiles which include phase boundary discontinuities. This link is generally applicable to analysis of interdiffusion data obtained by other techniques as well as by the microprobe. The primary function of the next program is to least-squares fit experimental diffusion data to the normal Arrhenius function: D = Doexp(-Q/RT), to obtain values of Do and Q. In addition the probable error and one, two, and three u statistical confidence limits of DO, Q, and log D are evaluated. This program is also directly useful for analysis of any other simple temperature-activated processes including conductivity, and certain deformation and chemical processes. The program to generate calibration curves for film-thickness determination using the microprobe is based on a numerical integration of the equation derived by Cockett and ~avis.' Values of film thickness obtained by this program for copper on various substrates are in good agreement with measurements made by other techniques. Versions of the above program system have been prepared for use with or without a remote teletype connection to the computer for processing on either a real-time or time-share basis. The instrumentation coupling a microprobe to a teletype for automatic data collection and analysis by the presently described program system has been reported elsewhere by the authors.' If teletype equipment is not used to communicate with the computer, standard methods of card reading and tape reading can be used. In either

Jan 1, 1967

By J. Chipman

There is no better way of paying tribute to the memory of a scientist than by developing and carrying forward those ideas which he has contributed to science and which are for us the very essence of his immortality. For a lecturer who has not had the great privilege of stdying under Professor Howe or 'ven of knowing him in person, these ideas must be transmitted through the printed word. It is our great good fortune that Professor Howe left to us a rich heritage of publication, not only in his classic monograph on the "Metallography of Steel and Cast Iron" but in a wealth of earlier hooks and papers in the transactions of this Institute arid of other scientific and engineering bodies. An outstanding characteristic of this published record is the great breadth of interest and of vision which it portrays. His was riot a narrow specialization in only the scientific aspects of ferrous metallographg. On the contra1y many of his important contributions had to do with a far broader field of metallurgicial endeavor. He insisted that his students be well grounded in 1 he fundamentals underlying the whole field and not led into the narrow groove of specific applications. Among his first major publications we find papers on copper smelting, extraction of nickel, the efficiency of fans and blowers, thermic curves of blast furnaces, the cost, of coke, and the manufacture of steel. These are the papers of a metalhurgical engineer and it was among engineers that Henry Marion Howe made his early and well-merited reputation. These early engineering contributions display very clearly the strongly sctientific inclination of their author. The classic work on "The Metallurgy of Steel" published in 1890 contains a thorough and critical discussion of all that was known at the time concerning the alloys of iron and of what we would now call the physical metallurgy of steel. In addition it describes steel-making processes in use and some that had become obsolete, and points out in critical fashion the reasons for success and failure. Steel mill design and layout were included as well as some pertinent discussion of refractories. The book is indeed an embodiment of one of Howe's outstanding characteristics—breadth. It is both the science and the engineering of steel production as known in that day. One of Howe's earliest technical papers was entitled "What is Steel?" That was nearly seventy-five years ago when many new processes and new kinds of steel were being developed. The time was ripe for such a question and the answers which Howe was able to give were helpful in understanding the phenomena of heat treatment. Twenty-five years ago Professor Sauveur repeated the question as the title of the first Henry Marion Howe Memorial Lecture. It seemed to him that this question, "What is Steel?," had served as Howe's motto throughout the remainder of his life. Today I shall present for your consideration a question of another sort: "What is Sletallurgy?" Perhaps it is not too much to hope that in the answer we may obtain a clearer and possibly broader view of the nature of our science and our profession. The time is ripe for giving careful consideration to what we mean by metallurgy. If our Metals Branch is to become in fact an American institute of Metallurgical Engineers, it is essential that we understand what is meant by metallurgical engineering. I am convinced that the best interests of the profession have not been served by a narrow interpretation of these terms. We must now place emphasis on the breadth of metallurgy as a science and as an engineering profession. With its usual brevity and wit. Webster's dictionary definesmetallurgy as "the science and art of extracting metals from their ores, refining them and preparing them for use." I shall riot assume that the words "science" and "art" and "metal" are so well understood as to require no defining but others among our contemporaries are better qualified than either your lecturer or the dictionary to present the broad meanings of these terms. When we say that metallurgy is among the oldest of the arts we are not classing it with painting or sculpture or music but rather with the making of tools or weapons or the building of bridges or chariots or cathedrals. In short we are saying that metallurgy is among the oldest of the engineering professions. The question " What is metallurg ? " has been one of rather more than ordinary concern to those of us who have the task of developing a curriculum for the education of students in this field. This development has been going on in a number of universities over a period of some years. but there seems to be as yet no unanimity as to what such a curriculum should contain. I believe there is fairly complete agreement that it must be founded upon sound

Jan 1, 1950

By Francisco Cadena

THE construction of Norris Dam, built by the Tennessee Valley Authority on the Clinch River, a tributary of the Tennessee River, involved the production of coarse and fine aggregate for approximately 1,000,000 cu. yd. of concrete. A hammer-mill plant for the manufacture of sand from quarried rock was indicated as the most economical method of providing this material. The abrasive character of the feed as compared to the average hammer-mill feed made it necessary to control operations rather closely, and this resulted in the accumulation of many data bearing on production and maintenance. This paper will deal only with three specific sets of data, accompanied by such general information as may be necessary to explain the conditions under which they were obtained and followed by discussions on the relation of silica content to hammer wear, comparative costs of slugger and stirrup hammers, and comparative costs of tool-steel and manganese-steel grate bars. Coarse Aggregate Aggregate for the concrete poured at Norris Dam came from a dolomite quarry within 2000 ft. of the west abutment of the dam. Geologically this rock is known as a Knox dolomite. A typical chemical analysis is given in Table 1. TABLE 1 .-Typica.1 Chemica1 Analysis [PER CENT H20,1100F ............................................ 0.0'2 Ignitionloss ............................................. 43.56 MgO .................................................. 19.19 CaO .................................................... 29.07 FezO .................................................... 0.39 A1203 .................................................... 1.94 FezO .................................................... 0.39 A1203 .................................................... 1.94 ..................................................... 5.75 SO2.. .................................................. Tr.] Rock was carried by 12-yd. dump trucks to a 42-in. gyratory crusher set at 6 1/2 in. The product of the primary crusher was taken by a belt conveyor to a double-deck vibrating screen followed by a 5 1/2-ft. cone

Jan 1, 1937

By M. Metzger, J. Intrater

IN the large number of important studies on high-purity aluminum (e.g., recrystallization and grain growth, creep, internal friction), it does not seem to have been generally recognized that the iron content, despite its very low figure, has a strong influence on a number of properties. In part, its influence is due to the very low solubility of the Fe-A1 6 phase. For aluminum of about 99.99 pct purity, the iron content may be 0.001 to 0.004 pct. For values in this range, a second phase will be present below 410" to 480 °C. This was determined by extrapolation of a log solubility vs inverse temperature plot of the solid solubility data of Edgar.' One consequence is the inhibition of grain coarsening below the solubility limit. This is shown in Table I, which gives, for three iron contents, the annealing temperature required for the absence of grains smaller than 1/2 mm average diameter together with the minimum temperature for the presence of some grains larger than 2 mm diameter. The specimens were 1/4x 1 1/2-in. strips cut from hard-rolled 1/16-in. sheet supplied by the Aluminum Co. of America.

Jan 1, 1954

By Warren T. Smith

The Phelps Dodge Corp. Lavender pit is located in the Bisbee mining district near the town of Lowell, Ariz. A quartz monzonite porphyry exists as an intrusive stock and was the source of mineralization for the limestone replacement orebodies being mined by underground methods. Leaching of the upper portion of the stock, and precipitation of the copper as chalcocite on the finely dispersed un- oxidized pyrite in the monzonite porphyry, formed a low grade ore zone below a leached capping varying from 50 to 300 ft thick. Churn drilling starting in 1916 and supplemental churn drilling begun early in 1950 indicated a mineable area about 3100 ft long by 2400 ft wide. In general drilling was on 100-ft centers. The pit was planned with 50-ft benches and wall slopes varying from 1 to 1 to a flatter slope of 1 1/3 to 1 dependent on the character of the ground. Materials within the pit limits, using a 0.6 pct minimum grade cutoff, were estimated at 41 million tons of 1.14 pct copper ore, 31 million tons of low grade sulfides suitable for leaching with an average grade of 0.42 pct, and 70 million tons of waste.

May 1, 1956

By H. M. FRENCH

ARC welding can be defined as a process whereby two A pieces of metal are brought together, heated to a molten state by the heat of an electric arc, and fused into one piece. There are several kinds of arc welding: the metallic arc, the carbon arc, the atomic hydrogen arc and the shielded arc methods. A short description of each, together with its major applications, will serve to distinguish between them. Metallic arc welding involves an arc drawn between a metal electrode and the material to be welded, called the work or the "parent metal." It may be further subdivided into hand and automatic welding, depending on whether the electrode is fed to the arc by hand or by motor drive. This form of arc welding can be applied to most welding operations. Exceptions to its use consist of applications where very thin metals are to be welded; where it is desired to join the work with- out adding metal; or where extreme ductility may be required:

Jan 1, 1930

Geological Survey of Ohio, Columbus, Ohio. Wilbur Stout, State Geologist. A complete list of publications will be sent upon request The present Geological Survey of Ohio is the fourth organization of this kind in the state The first Survey issued two reports, dated 1838 (not now available), the second, from 1869 to 1888, issued two reports, 75 cents and $1, respectively, and five volumes on geology, $1.25 to $3 50. The third organization, 1890 to 1900, issued a report for 1890, $1, and vol. 7 (1893), $150 Since 1900 the present organization has issued a number of Bulletins, most of which deal with the geology of some part of the state, as follows: Bulletin 10, The Middle Devonian (1909), 25 cents, 14, Columbus Quadrangle (1911), 30 cents; 15, Devonian and Mississippian of northwestern Ohio (1912), $1; 17, Conemaugh Formation (1912), 60 cents, 22, The Dunkard Series (1920), 60 cents; 23, Camp Sherman Quadrangle (1921), 50 cents; 24, Wayne County (1921), 50 cents, 28, Columbiana County (1924), $1, 30, Delaware County (1926), 75 cents, 31, Vinton County (1927), $1; 35, Jefferson County (1930), $1. Other bulletins on Ohio geology and resources of most interest are.

Jan 1, 1933

By E. J. KENNEDY

THE 142D MEETING of the Institute is rapidly shaping up with splendid prospects of a strong technical program and the lighter side of this annual occasion amply provided for. The date is February 20 to 23. The technical sessions will be held in the Engineering Societies building; the smoker-dinner, the informal dance, and the annual reception and dinner, at the Commodore Hotel, Monday, Tuesday and Wednesday respectively. The news to date on the technical side is as follows: Mining Methods-Subsidence The Mining Methods Committee has prepared an interesting program which will be divided into two sessions to be held early in the week. At the first there will be papers on mining methods and development, including a description of the "Sinking and Equipment of No. 2 Shaft at Minas de Matahambre," by Dudley D. Homer and R. H. Cromwell. They describe in considerable detail the equipment used and the practice followed in sinking this important shaft, giving detailed costs and performance figures. Hoist¬ing ?arrangements and mining practice at the "Red Ore Mines of the Woodward Iron Co. at Bessemer, Ala.," are described by Tenny C. DeSollar, superintendent of mines, in a second paper. At this session of the Mining Methods Committee, H. M. Roche and R. E. Crockett, of the Committee on Eastern Magnetite Mining and Milling Methods, will present their paper, "Iron Ore Mining at the Scrub Oak Mine." This mine is in the highlands of New Jersey about 40 miles west of New York City. Prof. Robert K. Warner of Yale University will present a paper on "The Selection of a Mining System," which should have an interesting discussion. Pierre R. Hines, of Portland, Ore., will present, with stereopticon slides, his paper on "The Owyhee Tunnels, U. S. Reclamation Project, Owyhee, Oregon," describing one of the recent irrigation undertakings.

Jan 1, 1933

By CHARLES E. W.

I. LOCATION. THE Mojave mining district is situated in a group of small hills centering around Soledad peak, in the Mojave desert, Kern county, Cal. These hills are about 4.5 miles SSW. of Mojave, a railroad town at the junction of the Santa Fé and Southern Pacific railroads. The town of Mojave is about 50 miles north of Los Angeles, to which it is connected both by telegraph and by rail. The distance on the Southern Pacific railroad is 102 miles, covered in 3 hr. and 45 min. by express train. A sketch-map of this region is shown in Fig. 1. The Mojave district is relatively isolated. The only other mining towns in this section of California are Randsburg and Johannesburg, in a district (containing the well-known Yellow Aster mine) at the northern end of a low ridge of hills, which begins about 20 miles NE. of Mojave, runs nearly N. for 35 miles, and varies in width between 3 and 6 miles. As will be seen later, the origin and formation of these hills are not the same as those of Soledad peak. II. CLIMATE AND VEGETATION. The climate and vegetation of the Mojave district are typical of the arid regions of the southwestern United States. During the winter and spring there is some rainfall, and the tempera-ture is generally from 60° to 70° F. in the day-time. The rainfall in the spring is often very considerable for short spaces of time, and cloud-bursts are not infrequent. In summer there is continual sunshine, with temperatures, as a rule, exceeding 100° F. in the day-time, while 115° F. in the shade of a house is not at all unusual; but at night the temperature falls considerably. No rain falls during the summer. The vegetation

Jan 1, 1906

By F. G. BREYER

ZINC metallurgists continue to follow with keen interest reports of successful results from the continuous retort plants at Palmerton, Pa., and Meadowbrook. W. Va. The new process had already demonstrated its ability to reduce the lead content of the metal and to effect savings in labor and fuel. The past year has shown that the retorts themselves can he built to last long enough so that the retort cost per ton of metal is lower than in past practice with small horizontal re- torts. A number of the latest type of retorts are reported to have been in continuous operation for over 18 months without a failure and are said to be still in good condition. This seems a complete answer to the last question which remained before continuous zinc smelting could he pronounced commercially practicable.

Jan 1, 1932

By G. H. Tausch, T. A. Huber

Very encouraging progress has been made ill the develop-ment of the permanent-type well completion which decreases considerable the cost of completions and workovers and aid-in the acquisition of reliable reservoir information at low cost. Completion and remedial operations are performed with tool,; which pass through the well tubing. Perforating and plug-hack operations can be done with the tubing in place and do not require pipe-handling equipment. Because of the many advantages afforded by this method, development work is going forward in anticipation of ultimately being able 10 use it to perform all usual well completion and workover operations. Effort is also being directed to the development of a more permanent type of lift equipment suitable for use with the permanent-type well completion. INTRODUCTION The permanent-type well completion in one in which the tubing and well-head are set in place only once in the life of the well and the completion or remedial work is performed through the tubing with a tubing-type perforator. a retrievable tubing extension. and other wire-line tools. This new type completion has made possible the saving of one to two days' rig time in the completion of each of several hundred wells During the last two years, and use of equipment developed for this type of completion has resulted in a 75 per cent reduction in cost. of certain types of workovers. In addition. the more reliable indication of the commercial value of a reservoir and the more accurate general reservoir information made Possible promise to be of even greater value in oil recovery than the reduction of costs for completions and workovers Recently. several well.. were worked over by using the retrievable tubing extension suspended on a swab line to plug back with cement and then perforating a higher producing interval with the tubing-type perforator, thus opening the way for complete through-the-tubing workovers which may be performed without pipe-handling equipment or mud. Those items attendant to the use of pipe-handling equipment and mud. such as hoard matting rig substructure. and pits. were also eliminated. There are indications that the elimination of drilling mud during completion and workover operations will frequently give increased well productivity, as plugging of the perforation. will not occur. It ii now possible to perforate selectively small sections of the producing interval and to test a well through these sections prior to perforating more interval. The perforating of additional interval will not entail the costly operations of killing the well and pulling tubing, nor will the old or the new perforations be plugged. The productivity of .mall sections of a reservoir and the actual gas-oil or oil-water contacts may now be determined economically under flowing condition.. Selective completions can be made in this manner to delay gas and water problems and bring about maximum oil recovery. At the present time, gas lift appears to offer the greatest potentialities for artificial lift in the permanent-type well com"letion since it can provide full-open tubing to accommodate the through-the-tubing tools and it may be ultimately developed into a fairly permanent type of lift. With precent-day pas-lift equipment. valve or mandrel failure necessitates occacio11al removal of the tubing. thereby reducing to some extent the permanence of the completion. New gas-lift valves are now

Jan 1, 1953

Discussion of the paper of HOWARD N. EAVENSON, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 94, October,' 1914, pp. 2637 to 2660. GEORGE S. RICE, Pittsburgh, Pa.-I think it is very wise to point out the greater liability to explosions in certain parts of the year, if there be such difference, with the caution, however, that vigilance be not relaxed at other times. In comparing the figures for the United States with those of Europe, I think we should separate them as far as possible according to cause of origin and means of propagation. That is to say, it would appear to me that the majority of our explosions are due more directly to the ignition of coal dust directly from the flame of explosives, whereas, judging from my inquiries and observations in some of the mines of Europe, the majority of their explosions have been caused by the ignition of fire damp. Now, in the case of fire damp, I do not think that anybody has yet attempted or has been able to find any connection between the seasons and the issuance of methane into mines. One thing must be borne in mind, that if you get a strong explosion of fire damp, dust of a character that might not ignite readily by itself might assist in the extension of an explosion of fire damp through a considerable area in the mine, if not throughout the mine. While it is true we have many lesser explosions in this country attributable to fire damp, it would appear that the majority of all the mine explosions of the country, in considering the means of propagation beyond the locality of the origin, are due to coal dust; and it is the liability to coal-dust explosions that appears to be affected by seasonal changes. Hence the desirability of separating statistically (if it could be done by the inspectors) fire-damp explosions from coal-dust explosions, in order to obtain the true value of the seasonal effect. Nevertheless, in spite of the inclusion of fire-damp explosions with coal-dust explosions, the preponderance of the evidence, as indicated in Mr. Eavenson's figures for American mines, has shown that' in this country there were more explosions in the winter and spring months, when the mines are drier; that is, when the mines are apt to be drier. Whereas, according to the European figures that he has gathered, it seems to be very clearly demonstrated that in France, England, and Belgium, the time when explosions occur has no connection with any particular season. That, I think, is partly due to the point just mentioned, that a majority of their explosions have originated from fire damp. The European mining men have been more careful, generally speaking, with the use of explosives than we have, so that the cause of ignition from that source has been less. Only comparatively few of the mines in foreign

Jan 4, 1915

By R. J. Mellen

IN a chloridizing roasting and cyanidation plant treating a manganese-silver ore, certain experiments pointed out the way to an improvement in roasting conditions by a change in the degree of crushing. The following short article is simply a description of the various changes that were necessary throughout the plant and of the results obtained. There is nothing unusual in these changes but they are of some interest in that they constitute a good many of the alterations usually resorted to in increasing production. In the beginning, the changes were brought about by an experiment that was not successful, but which clearly pointed to means of improving the operation, and is an example of the fact that often experimental work may result in failure and still be of value in arriving at correct fundamentals. This experiment also shows how far a metallurgist can get out of line in his deductions, particularly in a field with which he is not thoroughly familiar. The ore at the plant of Compania Minera Kildun y Anexas is crushed through a 13-in. gyratory, a 3-ft. standard Symons cone crusher and a set of 16 by 42in. rolls, the latter in closed circuit with two Tyler 400-mesh screens. The crushed ore is then conveyed to two fine-ore bins. These provide storage and feed for two 6 by 90-ft. kiln roasters, which discharge directly to coolers. The coolers in turn discharge to a 6 by 12-ft. ball mill, where the ore is ground for cyanidation. Laboratory and pilot-plant tests previous to the mill construction had indicated that minus ¼ -in. crushing was satisfactory for roasting, although results did not vary greatly with some coarser or considerably finer crushing. The plant was designed for a capacity of 300 tons per day on this basis. After a few months operation, the initial operating problems were overcome and the anticipated milling rate was reached but the results being obtained were not really good. The plant seemingly did not have much excess capacity in any department but the roasting operation was the most critically limiting factor both as to tonnage and the results obtained. If this could be improved there seemed some possibility of improving the total tonnage rate to some extent. Segregation of the calcine into various screen sizes showed that the coarser sizes ,were not giving the expected recoveries. In all of the laboratory and pilot-plant testing, any limiting conditions as to the percentage of salt used, temperatures, feed rates, etc., had affected the fine material more than it had the coarse, and even in making laboratory tests at this time the mill conditions could not be exactly duplicated. Further laboratory testing indicated that a segregation of the crushed ore into a coarse and fine product for roasting might result in some improvement in roast-

Jan 1, 1945

By R. J. Mellen

In a chloridizing roasting and cyanida-tion plant treating a manganese-silver ore, certain experiments pointed out the way to an improvement in roasting conditions by a change in the degree of crushing. The following short article is simply a description of the various changes that were necessary throughout the plant and of the results obtained. There is nothing unusual in these changes but they are of some interest in that they constitute a good many of the alterations usually resorted to in increasing production. In the beginning, the changes were brought about by an experiment that was not successful, but which clearly pointed to means of improving the operation, and is an example of the fact that often experimental work may result in failure and still be of value in arriving at correct fundamentals. This experiment also shows how far a metallurgist can get out of line in his deductions, particularly in a field with which he is not thoroughly familiar. The ore at the plant of Compania Minera Kildun y Anexas is crushed through a 13-in. gyratory, a 3-ft. standard Symons cone crusher and a set of 16 by 42-in. rolls, the latter in closed circuit with two Tyler type 400 screens. The crushed ore is then conveyed to two fine-ore bins. These provide storage and feed for two 6 by 90-ft. kiln roasters, which discharge directly to coolers. The coolers in turn discharge to a 6 by 12-ft. ball mill, where the ore is ground for cyanidation. Laboratory and pilot-plant tests previous to the mill construction had indicated that minus ¼-in. crushing was satisfactory for roasting, although results did not vary greatly with some coarser or considerably finer crushing. The plant was designed for a capacity of 300 tons per day on this basis. After a few months operation, the initial operating problems were overcome and the anticipated milling rate was reached but the results being obtained were not really good. The plant seemingly did not have much excess capacity in any department but the roasting operation was the most critically limiting factor both as to tonnage and the results obtained. If this could be improved there seemed some possibility of improving the total tonnage rate to some extent. Segregation of the calcine into various screen sizes showed that the coarser sizes were not giving the expected recoveries. In all of the laboratory and pilot-plant testing, any limiting conditions as to the percentage of salt used, temperatures, feed rates, etc., had affected the fine material more than it had the coarse, and even in making laboratory tests at this time the mill conditions could not be exactly duplicated. Further laboratory testing indicated that a segregation of the rushed Ore into a coarse and fine product for roasting might result in some improvement in roast-

Jan 1, 1947

By R. J. Mellen

In a chloridizing roasting and cyanida-tion plant treating a manganese-silver ore, certain experiments pointed out the way to an improvement in roasting conditions by a change in the degree of crushing. The following short article is simply a description of the various changes that were necessary throughout the plant and of the results obtained. There is nothing unusual in these changes but they are of some interest in that they constitute a good many of the alterations usually resorted to in increasing production. In the beginning, the changes were brought about by an experiment that was not successful, but which clearly pointed to means of improving the operation, and is an example of the fact that often experimental work may result in failure and still be of value in arriving at correct fundamentals. This experiment also shows how far a metallurgist can get out of line in his deductions, particularly in a field with which he is not thoroughly familiar. The ore at the plant of Compania Minera Kildun y Anexas is crushed through a 13-in. gyratory, a 3-ft. standard Symons cone crusher and a set of 16 by 42-in. rolls, the latter in closed circuit with two Tyler type 400 screens. The crushed ore is then conveyed to two fine-ore bins. These provide storage and feed for two 6 by 90-ft. kiln roasters, which discharge directly to coolers. The coolers in turn discharge to a 6 by 12-ft. ball mill, where the ore is ground for cyanidation. Laboratory and pilot-plant tests previous to the mill construction had indicated that minus ¼-in. crushing was satisfactory for roasting, although results did not vary greatly with some coarser or considerably finer crushing. The plant was designed for a capacity of 300 tons per day on this basis. After a few months operation, the initial operating problems were overcome and the anticipated milling rate was reached but the results being obtained were not really good. The plant seemingly did not have much excess capacity in any department but the roasting operation was the most critically limiting factor both as to tonnage and the results obtained. If this could be improved there seemed some possibility of improving the total tonnage rate to some extent. Segregation of the calcine into various screen sizes showed that the coarser sizes were not giving the expected recoveries. In all of the laboratory and pilot-plant testing, any limiting conditions as to the percentage of salt used, temperatures, feed rates, etc., had affected the fine material more than it had the coarse, and even in making laboratory tests at this time the mill conditions could not be exactly duplicated. Further laboratory testing indicated that a segregation of the rushed Ore into a coarse and fine product for roasting might result in some improvement in roast-

Jan 1, 1947