Search Documents

By K. A. SPENCER

THE production of soft coal from strip mines in the United States has shown a remarkable growth in the last sixteen years, increasing from one and one-quarter million tons in 1914 to approximately twenty-two million tons in 1929. This is a growth of approximately 1660 p& cent, as compared with a growth of approximately 20 per cent in the underground mines for the same period. But even with this marked in- crease the total tonnage produced by open-face mining represents only 4 per cent of the nation's soft coal tonnage.

Jan 1, 1931

By W. C. Knoblaugh

Rotary kilns are adaptable to many fuels, but this paper deals principally with the use of powdered coal. The observations and conclusions presented are based on rotary kilns used in the manufacture of basic refractories for steel furnaces. Solid fuels are pulverized for two principal reasons: (I) ease of control, and (2) rapidity of combustion. By the use of pulverized coal, the operator can increase or decrease the fuel supply by small increments and with very little time lag between the change of control and the resultant change in the flame. This is extremely important in this type of furnace, as the temperature range for maturing the clinker is very narrow. By fine grinding, it is possible to increase the rate of burning of the coal, thereby liberating great quantities of heat within a small space in a short time. Under given conditions, temperature is a measure of the heat liberated per unit of time. To attain the temperatures of 2950° to 3150ºF., which are encountered in the manufacture of various steel-furnace refractories, it is estimated that it is necessary to liberate 125,000 to 175,000 B.t.u. per cubic foot of the burning zone per hour. The manufacture of dolomitic refractories is a ceramic process and, as is true in most such processes, the material must be subjected to a certain critical temperature for a certain length of time in order to complete the reaction. If the time of reaction is reduced, the temperature must be increased; in other words, if the rate at which the material flows through the hot zone of the kiln is increased, the temperature of the hot zone must be increased to compensate for this shorter exposure to the flame. Firing with Pulverized Coal Fig. I is a line drawing of a rotary kiln with the attendant equipment indicated in their relative positions. The kiln proper consists of a sloping, refractory-lined steel tube rotating slowly about its longitudinal axis (0.75 r.p.m.), and is countercurrent in operation in that the raw feed is introduced at the stack end and gradually approaches the zone of highest temperature at the lower end, where the fuel is introduced. Before 1930, the usual method of firing a rotary kiln was to store the coal in the pulverized form and then feed from this storage to the kiln as needed. This proved unsatisfactory and dangerous because of dust explosions and the inability to obtain an even feed to the kiln caused by arching of the coal in storage and flooding of the coal feeders. In later years the practice has been to store the raw coal and grind it as it is needed. Such a layout is indicated in Fig. I. The coal is stored in bins, charged from the top and drawn from the bottom into recording scales and then into some type of unit pulverizer. There are a number of good pulverizers .on the market, each incorporating features that the manufacturer considers outstanding.

Jan 1, 1948

By W. C. Knoblaugh

ROTARY kilns are adaptable to many fuels, but this paper deals principally with the use of powdered coal. The observations and conclusions presented are based on rotary kilns used in the manufacture of basic refractories for steel furnaces. Solid fuels are pulverized for two principal reasons: (I) ease of control, and (2) rapidity of combustion. By the use of pulverized coal, the operator can increase or decrease the fuel supply by small increments and with very little time lag between the change of control and the resultant change in the flame. This is extremely important in this type of furnace, as the temperature range for maturing the clinker is very narrow. By fine grinding, it is possible to increase the rate of burning of the coal, thereby liberating great quantities of heat within a small space in a short time. Under given conditions, temperature is a measure of the heat liberated per unit of time. To attain the temperatures of 2950° to 3150°F., which are encountered in the manufacture of various steel-furnace refractories, it is estimated that it is necessary to liberate 125,000 to I75,000 B.t.u. per cubic foot of the burning zone per hour. The manufacture of dolomitic refractories is a ceramic process and, as is true in most such processes, the material must be subjected to a certain critical temperature for a certain length of time in order to complete the reaction. If the time of reaction is reduced, the temperature must be increased; in other words, if the rate at which the material flows through the hot zone of the kiln is increased, the temperature of the hot zone must be increased to compensate for this shorter exposure to the flame. FIRING WITH PULVERIZED COAL Fig. I is a line drawing of a rotary kiln with the attendant equipment indicated in their relative positions. The kiln proper consists of a sloping, refractory-lined steel tube rotating slowly about its longitudinal axis (0.75 r.p.m.), and is countercurrent in operation in that the raw feed is introduced at the stack end and gradually approaches the zone of highest temperature at the lower end, where the fuel is introduced. Before 1930, the usual method of firing a rotary kiln was to store the coal in the pulverized form and then feed from this storage to the kiln as needed. This proved unsatisfactory and dangerous because of dust explosions and the inability to obtain an even feed to the kiln caused by arching of the coal in storage and flooding of the coal feeders. In later years the practice has been to store the raw coal and grind it as it is needed. Such a layout is indicated in Fig. I. The coal is stored in bins, charged from the top and drawn from the bottom into recording scales and then into some type of unit pulverizer. There are a number of good pulverizers on the market, each incorporating features that the manufacturer considers outstanding.

Jan 1, 1946

By W. C. Knoblaugh

Rotary kilns are adaptable to many fuels, but this paper deals principally with the use of powdered coal. The observations and conclusions presented are based on rotary kilns used in the manufacture of basic refractories for steel furnaces. Solid fuels are pulverized for two principal reasons: (I) ease of control, and (2) rapidity of combustion. By the use of pulverized coal, the operator can increase or decrease the fuel supply by small increments and with very little time lag between the change of control and the resultant change in the flame. This is extremely important in this type of furnace, as the temperature range for maturing the clinker is very narrow. By fine grinding, it is possible to increase the rate of burning of the coal, thereby liberating great quantities of heat within a small space in a short time. Under given conditions, temperature is a measure of the heat liberated per unit of time. To attain the temperatures of 2950° to 3150ºF., which are encountered in the manufacture of various steel-furnace refractories, it is estimated that it is necessary to liberate 125,000 to 175,000 B.t.u. per cubic foot of the burning zone per hour. The manufacture of dolomitic refractories is a ceramic process and, as is true in most such processes, the material must be subjected to a certain critical temperature for a certain length of time in order to complete the reaction. If the time of reaction is reduced, the temperature must be increased; in other words, if the rate at which the material flows through the hot zone of the kiln is increased, the temperature of the hot zone must be increased to compensate for this shorter exposure to the flame. Firing with Pulverized Coal Fig. I is a line drawing of a rotary kiln with the attendant equipment indicated in their relative positions. The kiln proper consists of a sloping, refractory-lined steel tube rotating slowly about its longitudinal axis (0.75 r.p.m.), and is countercurrent in operation in that the raw feed is introduced at the stack end and gradually approaches the zone of highest temperature at the lower end, where the fuel is introduced. Before 1930, the usual method of firing a rotary kiln was to store the coal in the pulverized form and then feed from this storage to the kiln as needed. This proved unsatisfactory and dangerous because of dust explosions and the inability to obtain an even feed to the kiln caused by arching of the coal in storage and flooding of the coal feeders. In later years the practice has been to store the raw coal and grind it as it is needed. Such a layout is indicated in Fig. I. The coal is stored in bins, charged from the top and drawn from the bottom into recording scales and then into some type of unit pulverizer. There are a number of good pulverizers .on the market, each incorporating features that the manufacturer considers outstanding.

Jan 1, 1948

By AIME AIME

To accompanying photograph of the plant of the Beattie Gold Miner Limited, at Duparquet,. Quebec, is taken from the east and shows the open-pit from which the ore is taken during the summer. The buildings on the level ground above the open-pit are the change rooms, steel shop hoist building, compressor building, machine shop, warehouse, carpenter shop, and oil house. The main five-compartment shaft is shown west of the hoist building. The crusher plant adjoins the headframe and a long conveyor transports the fine ore

Jan 1, 1936

R. V. NorHis, Wilkes-Barre, Pa. (communication to the Secretary*) : The electric-haulage plant of the Short Mountain Colliery of the Lykens Valley Coal Co., mentioned by Messrs. Stoek and Harris as the earliest underground electric plant in the United States (and, I believe, the second in the world), was started July 23, 1887. The plant, designed by W. M. Schlessinger, consists of two motor-cars, each weighing about 5 tons and equipped with a 32-h.p. Union Electric Go. motor. The original general construction of the motor-cars is shown by Mr. Stoek; but they were rebuilt, the same year, with some important improvements in design; and, except for strengthening the frames and replacing the original pig-iron weights by a casting, they have not been greatly changed since that time. The generating-plant consists of two Union Electric Co. dynamos of 65-h.p. each, driven by an old 18- by 48-in. plain slide-valve engine; the ordinary voltage is 450 and the amperage varies from 40 to 200; the average indicated h.p. of the engine is about 75, with a steam-consumption of about 75 lb. per i.h.p. per hour; and as the cost of steam at this colliery is 8.11 cents per 1,000 lb.,the steam-cost per day is about $4.56.

Jan 1, 1904

By John B. Hastings

TEN miles from Hartsel, near Antelope springs, in Park county, Colorado, there is a large area of unconsolidated lake beds, which are interesting because at least a part of the lacustrine sands contains in the aggregate an immense amount of gold. During 1906, one of the arms of this dessicated lake was fairly well prospected with shafts and cuts by an Eastern company to test its value, as favorable amounts of gold had in some instances been found upon it. The claims of the company contain about 5,000 acres of the beds; but this is only a small portion of them, a south branch from a main body, which is at least 7 miles in diameter, with other and very wide lateral gulches, paralleling the one herein described on the east and west. A certain amount of digging and sampling was done in the outside areas; but the result was evidently unsatisfactory, since the work was discontinued. his section of Colorado has not been studied geologically, and the age of the ancient lake is unknown. It is probably Quaternary. I spent two weeks on the ground, in September and October, 1906, but was quite absorbed in the sampling. I looked, however, for terraces on the rim-rock and other evidences of movement and erosion, but did not find anything to denote an earlier age than the Quaternary. The granite rim-rock may be Archean; S. F. Emmons says that some of the granites in central Colorado are as old as that. The rim-rock as observed is a gray quartzose biotite-granite, except a small area in Sections 3 and 34, where it is a felsitic (?) breccia. The breccia is silicified by solfataric action at the corner near Shaft No. 7, in Section 34; but this action is older than the sands and does not extend to them. The shaft averaged 50c. per ton, more than twice as much as the rest.

Jan 5, 1908

By H. H. Otto

COMPARED with 1939, the year 1940 has seen no material change in the production of anthracite. Many factors seem to indicate a stabilized anthracite production of approximately 50 million tons per year. The present war has stimulated demand in the Cana¬dian and New England markets, which were formerly furnished with a portion of their needs from Great Britain and other European countries. Neither has there been any material change in the "bootleg coal" situation. This problem is more serious in the Southern anthracite field than in the Hazleton, Wilkes-Barre, and Scranton areas. One reason for this is the nearness of the Southern field to the large anthracite markets in Philadelphia, Washington, Baltimore, and Harrisburg. During the past year no new large

Jan 1, 1941

By E. C. Lee

THE safety of mine workers has received more attention from both State and Federal law-making bodies than any other industry, a fact that shows clearly the hazardous nature of the industry. The last, but by no means the least, of the measures adopted for the protection of mine workers, is workmen's compensation legislation. This is proving to be a powerful instrument for greater safety in the industries, from the fact that special stress is laid not on how the accident happened or who may have been responsible for it, but on how badly the employee is hurt by it. The injured person does not have to employ lawyers to prove his case, because the mere fact of his employment is proof of his right to compensation. The immediate effect of such legislation is the certainty confronting the mine operator that he must pay out large sums for every accident, regardless of its cause, thus adding materially to the cost of the production of his coal. This fact furnished to the operator the strongest incentive to reduce the causes of accidents; not that the operator has ever lacked reasonable consideration for the welfare of his employees and a proper humane interest in their safety, but his engrossment in earning his daily livelihood has been so great that he has not felt that he had the time to devote to the safety of the operation. This time he must now find because of the actual-cash value of the prevention of accidents in his mines. This agency alone proved inadequate to bring about a material improvement because operators have always been willing enough to improve safety conditions when possible to do so within reasonable limits of their financial ability. The requirement in the Workmen's Compensation Laws of several of the States, that the mine operator shall insure as a guarantee of his ability to meet his compensation obligations, has furnished the needed incentive, moral and financial, necessary to the prompt and effective dissemination of a more general knowledge of the causes and

Jan 10, 1917

By AIME AIME

A SYMPOSIUM on current. conditions in Mexico, particularly in the oil and mining industries, was a most successful feature of the May meeting of the New York Section of the A.I.M.E. Heath Steele, vice-president of The American Metal Co.. Ltd., with an intimate knowledge of Mexico gave the principal address, and asked that his analysis of the present situation he regarded neither as an endorsement of Mexico's policy nor as the criticism of a disgruntled operator. To explain the .attitude of the great mass of the Mexican people towards recent developments, he first described briefly the political, social, and religious beliefs and customs of tile Mexican Indian. In spite of their contact with foreigners these beliefs and customs have remained unchanged throughout many generations. The old communal spirit and the idea of common ownership of the land still persist especially in the rural districts and villages; the old custom of a council for local self-government is reflected in the present-day labor committee. Mr. Steele discussed in order land oil, and mines.

Jan 1, 1938

Fred. T. Greene, Rossland, B. C. (communication to the Secretary): At the beginning of his gaper, Mr. Herzig refers to an article of mine in the Engineering and Mining Journal of January 27, 1900. I would like to add that the method de-

Jan 1, 1901

By J. Versluys

When a well strikes an oil-bearing layer, the oil has a pressure which is generally sufficient to enable it to rise to near the surface (sometimes above the surface). As soon as a well begins to produce, however, the liquid moves through the pores of the reservoir bed and the pressure in the well becomes much lower than the pressure originally prevailing there. At some distance from the well, however, the pressure in the reservoir bed remains unaltered; thus the pressure of the oil has not only to lift the oil, but also to overcome the friction resistance in the pores. The fact that so many oil wells are gushers is a consequence of the energy accumulated in the gas. In gushing the well acts as a gas-lift. A mixture of liquid and gas (the latter partly dissolved in the former) rises vertically from the oil-bearing layer through a cylindrical casing to the surface. In time conditions alter and the well ceases to gush regularly, then the gushing can be further promoted by inserting a narrower tube in the well and connecting the top of the oil string to the tubing. If the action in time becomes irregular, the gushing can be kept up for a further period by forcing gas between the two tubes. In the oil fields the term "gas-lift" is used actually only where extraneous gas is applied, as in the last of the stages mentioned. The action, however, is just the same whether the gas exclusively originates from the formation, or is partly applied artificially. Thus by gas-lift we simply mean a vertical tube in which the energy of gas under pressure, and of dissolved gas, is utilized for raising a liquid. In gushing oil wells the pressure is frequently very high and the absorption coefficient 0.4 (expressed in vol. ratio) of the coexisting gas is not particularly high, so that in reality it should be assumed that a considerable portion of the gas, at any rate at the bottom of the gas-lift, is dissolved in the oil. For water-producing wells this is not usually of such importance. Where the volume of the flowing gas is much greater than that of the flowing liquid, the latter can be suspended in the former in the form of

Jan 1, 1930

By E. J. Roberts

F. C. Bond (Allis-Chalmers Mfg. Corp., Milwaukee) —This paper considers comminution as a first order process, with the reduction rate depending directly upon the amount of oversize material present. The data show that other factors should be taken into account, and it is possible that in time these may be evaluated as simultaneous or consecutive reactions: Development of the theory of comminution has been retarded for many years by the assumption that surface area measurements constitute the sine qua non of the work done in crushing and grinding, and it is encouraging to note the belated growth of other ideas. In the Abstract the term "net power" should be changed to "net energy." Throughout the paper the term "hp per ton" should be changed to "hp hrs per ton", or "hp hr t." The term "Probability Theory" in the title does not seem appropriate, since it is not clear how the probability theory is used in developing the ideas in the paper. There seems to be a contradiction between the large calculated advantages of closed circuit operation and the statement following that the closed circuit test results showed no significant change in grinding behavior, when compared with the batch grind curves. Tables I and II show that between 75 pct and 50 pct solids the energy input required decreases with increasing moisture content and may indicate the advisability of grinding at higher dilutions in certain cases. The calculation of the hp-hr per ton factor indicates an input in the laboratory mill of only 7.32 gross hp per ton of balls; this casts some doubt upon the accuracy of the factor used, since the power input in commercial mills at 80 pct critical speed is customarily much higher. The tests show that within fairly wide limits the amount of ore in the laboratory mill may be varied and a product of constant fineness obtained, provided that the grinding time is varied in the same proportion. This has often been assumed, and confirmation by actual testing is of value. The Cavg corrections for differences between the plant and laboratory size distributions do not seem very satisfactory, since in many cases the plant/laboratory ratio is farther from unity after correction than before. The following equation has been derived from the data in Table VI: Relative Energy (log new ball diam in in. + 0.410) Input = --------------—--------------- from which the relative energy inputs for balls of different sizes can be calculated and compared. The relative energy input is unity for balls of 2.715 in. diam. The equation indicates that the work accomplished by a ton of grinding balls per unit of energy input is roughly proportional to the square root of the total ball surface area; provided, of course, that the balls are sufficiently large to break the material. The data in support of this statement are admittedly meager, but are fairly consistent when plotted. The relative grindability values listed in Table VI for 200 mesh multiplied by 4/5 apparently correspond approximately to the A-C grindability at 200 mesh.' It would seem that for open circuit tests comparable accuracy could be obtained much more simply by the old method' of plotting the test grind, extending the mesh grinds to the left of zero time if necessary, and determining from the plot the equivalent time required to grind from the plant feed size to the plant product size, using the average of several mesh sizes. The en- ergy input value of one time interval could be determined by tests on materials of known grinding resistance, and this multiplied by the interval required should give the desired energy input value. The relative grindabilities would be the relative time intervals required for a specified feed and product size. When the plotted mesh size lines of a homogeneous material are extended to the left beyond zero time they meet at one point at zero pct passing. The horizontal distance of this point from zero time indicates the equivalent energy input required to prepare the mill feed. The author's results show that the closed circuit grinding tests give about the same K values as open circuit tests, from which he concludes that open circuit tests are satisfactory in many cases. The value of the closed circuit test is its ability accurately to predict energy requirements in closed circuit grinding for both homogeneous and heterogeneous materials. If the material is homogeneous, the open circuit test gives satisfactory results; but if the material contains appreciable fractions of hard and soft grinding ore, the open circuit tests will not be accurate because of the accumulation of hard grinding material in the circulating load. Since in most cases it is not possible to determine a priori whether the material contains hard and soft fractions, the closed circuit tests are preferable and more reliable. B. S. Crocker (Lake Shore Mines, Ontario)—Dr. Roberts probability theory of grinding is very similar to our log pct reduced vs. log tonnage method of plotting and evaluating grinding tests at Lake Shore. However, although we both seem to start at the same point we finish with different end results. Shortly after publishing our grinding paper (referred to by Dr. Roberts) in 1939, we did pursue the subject of the "constant pct reduction in the pct +28 micron material for each constant interval of time. We ran innumerable tonnage tests on the plant ball mills, rod mills, tube mills with 11/4 and 3/4 balls, and lastly pebble mills, with tonnage variations from 180 tons per day to 950 tons per day. We found that when we plotted the log of the tonnage against the log of the pct reduced of any reliable mesh, we had a straight line up until 90 pct of the mesh is reduced. We have also tested this in our 12-in. laboratory mill with the same results. We have used this method of evaluating grinds for the past 8 years and developed the recent four stage pebble plant on this basis. By pct reduced we mean the percentage of any given mesh that is reduced in one pass through a mill at a given tonnage (or time). For example, if the feed to a rod mill is 90 pct +35 mesh and the discharge at 500 tons per day is 54 pct +35, the pct reduced is 90 — 54/90 = 40 pct. If the feed had been 80 pct +35 the discharge would have been 48 pct +35 or pct re- duced 80-48/80 = 40 pct as long as the tonnage re- mained constant at 500 tons per day. Thus we can easily correct for normal variation of mill feeds. This log — log relationship derived from the tonnage tests of all our operating mills has proved of tremendous help in checking laboratory work and in designing alternate layouts or new plants. The difference between the log — log and the semi-log plot is only shown up when the extremes in tonnages are plotted. When the relationship between the pct reduced and the tonnage was first investigated, we used semilog

Jan 1, 1952

By R. A. Nadler and

Specimens of Ti-155A (Ti-5Al-1.3Fe-1.3Cr-1.2Mo), Ti-6Al-4V and Ti-4Al-3Mo-1V were hydrogenated, aged to high strength levels, and subjected to notched stress-rupture tests and tensile tests at two strain rates. Both Ti-6Al-4V and Ti-155A were relatively unaffected by hydrogen in amounts exceeding those found in commercially -produced material. Inconsistencies in the data and a relatively low initial level of ductility prevented an accurate determination of the hydrogen tolerance for aged Ti-4Al-3Mo-1V, but there was no evidence that this alloy was any more susceptible to hydrogen embrittlement than Ti-155A and Ti-6A1-4V. THE metallurgical literature has been considerably enriched in the past five years by the publication of the results of many investigations which were concerned with the effects of hydrogen on titanium and its alloys. Although it is not the authors' intention to provide a complete literature survey of this vast field, it is worthwhile to summarize briefly some of the important factors which influence the embrittling phenomenon in a - B alloys. Some of the influencing factors are those of strain rate, temperature, and composition. Hydrogen embrittlement in a - B titanium alloys is now believed to be a strain-induced phenomenon, and whether or not embrittlement occurs at high hydrogen levels depends largely upon whether sufficient time is available for hydride precipitation. This condition is fulfilled by tensile testing at very slow strain rates or by rupture testing smooth or, preferably, notched specimens over relatively long periods. Conveniently, maximum embrittlement occurs at or near room temperature. The presence B - stabilizing elements, in amounts sufficiently small to prevent an all -B or nearly all -P condition, promotes hydrogen embrittlement and this tendency is believed to be related to the amount of a - B interfacial area present. Aluminum, by increasing the solubility of hydrogen in A titanium, greatly reduces the danger of hydrogen embrittlement, while oxygen has been shown to have detrimental effects.' The preceding discussion is based on experimental work performed on annealed a - P alloys. This early work has shown that annealed Ti-6A1-4V and Ti-155A are relatively insensitive to the embrittling effects of hydrogen.' Although no work has been reported on annealed Ti-4A1-3Mo-lV, the alloy would be expected to exhibit somewhat the same insensitiv-ity as Ti-155A. In sharp contrast to the voluminous literature on annealed titanium alloys is the paucity of reported investigations on materials receiving commercial heat-treatment cycles. To date, the most notable contributions in this field have arisen from two separate investigations on Ti-3Mn-1Fe-1Cr-1V-lMo, the so-called 3Mn comple~. These investigations

Jan 1, 1961

By Frank J. Tolonen

BENEFICIATION of iron-bearing formations is one of the major problems of research at the Michigan College of Mining arid Technology. Funds for this purpose hate been supplied by the State of Michigan supplemented by contributions of labor and some supplies from the Federal Government during the depression. The iron-mining companies have cooperated in securing samples and have also furnished much valuable information relative to the various formations.

Jan 1, 1937

By Jerome Strauss

IN his review of developments in 1943, Gilbert Seil, Chairman of this Committee on Reduction of the Ferroalloy Ores, tabulated the consumption of the alloying metals in relation to the steel production of that year. In the year just closed the approximate tonnage was of the same order, differing only to a minor degree or suffering some correction with more precise figuses available, as indicated in the following estimates: Consumption Metals in Tons Steel 92,000,000* Manganese 700,000 Silicon 200,000 Chromium 200,000 Nickel 75,000 Molybdenum 20,000 Tungsten 8,000 Vanadium 1,700 Titanium 1.600 Boron 10 `Production figure. The technologic studies instituted during 1942 and carried forward with such great vigor during 1943 continued into 1944 although in some instances were brought to a close either by completion of the specific development

Jan 1, 1945

By P. A. Robbins

FAR NORTH, on the bare Arctic tundra, 11 mi. above the mouth of the Keewalik River where the latter discharges into Kotzebue Sound. several ., Eskimos garbed in parkies and muck lucks mingle with a small group of similarly clad white men. All of them shield their eyes from the white glare of the arc as a gasoline-driven arc-welding set rains molecules of metal on the break in a bull wheel, the large gear wheel which swings the boom and cab of a dragline shovel.

Jan 1, 1937

By Charles E. Parsons

One of the greatest factors in our industrial development is cheap and convenient power. Long-distance electrical transmission has now reached such a stage that it is feasible, and practicable, to utilize the water-power of the country which was heretofore too remote for consideration. In all of the changes of energy from its various sources to its electrical applications, water-power stands pre-eminent in point of economy. Power-users the world over have endeavored to utilize this force in preference to any other, and until long-distance transmission was found practicable it seemed that every available water-power in this section of the country was doing its full share for the benefit of mankind. The success of each great industrial development has been clue in a greater part to some one man one who is just a step in advance of the rest in his particular field; one who is able to grasp a situation and foresee possibilities; and, above all, one who has that indomitable pluck and perseverance which sees in each obstacle one more step toward success. Such a mail is Eugene L. Ashley, for it was through his efforts that the development of the greatest power on the Hudson river was made possible. For several years prior to 1897 the various properties along the river between Glens Falls and Palmer Falls were in the hands of speculators. These men knew the value of waterrights, but they had not the ability to assemble the properties and finance such an undertaking. In 1897 Mr. Ashley began buying these water-rights, and, after two years of litigation, title mas secured to all of the properties along each side of the river, and the Hudson River Water-Power Company was organized to construct a dam and transmit power to the surrounding cities and villages. A contract was let for a dam

Jan 1, 1904

G. M. TAYLOR,* Colorado Springs, Colo.-The ore treated at the United Eastern is primarily a gold one and is cyanided-the counter-current decantation method being employed. One of our employees visited this plant a few months ago and, on his return, reported that the moisture in the tailing was carrying 20 c. per ton, which would appear to be somewhat high. As this type of plant has been advocated by one of the recognized cyaniding engineering firms in the country, and a number of these plants are in successful operation, it does not seem to me that the dissolved loss could be so high, and I would like to know if any one can give any definite information on this point? J. V. N. DORR, New York, N. Y.-I am very glad that Mr. Taylor has raised this question. When I first read Mr. North's paper and saw his statement, that they had an actual dissolved loss of 21.5 c. per ton, I was very much puzzled at this high loss which appeared avoidable by another decantation or the addition of a rotary filter. Reading it again, however, I noted that the actual dissolved loss of 21.5 c. given was evi-dently obtained by multiplying the assay of solution discharged from Z. thickener by the tonnage. On the basis of 283 tons milled per clay, this means $56.54 going to the clam. He states, however, that he returns from. the dam into the system, 70 tons daily assaying 40 c. per ton or $28 per day, so it would seem reasonable, unless I have overlooked something to regard the actual dissolved loss as $56.54 less $28 or $28.54, equaling 10.8 c. per ton. Even this loss, however, is much higher than good practice elsewhere, and can be accounted for largely by the tonnage being handled, which I believe is 30 per cent. above the capacity planned.

Jan 12, 1919

KARL A. PAULY,* Schenectady, N. Y.-We are deeply indebted to Mr. Hobart for a record of the actual experience of the Lehigh Coal and Navigation Co. with electrification. One of the essential features of this test is that it was made under actual operating conditions. In one of the western mining districts I was once discussing the electrification of a large hoist with a mining operator, who told me that they had made a very thorough test and that the results were such as to indicate that electrification was not warranted. When questioned regarding the test, he said that they had called on the mining college in the Territory for assistance, and one of the instructors and a group of students had made the test. They first cleaned the boilers and then operated them at a' continuous load, using the maker's guaranteed steam consumption per indicated horsepower as a guide in estimating the steam consumption under actual hoisting conditions. Such a test is absolutely valueless. The efficiency of the boilers 'is affected by the intermittent demands on the steam. The standby losses, as indicated by Mr. Hobart's paper, are quite equal to the actual fuel consumption required to do the work; very frequently, also, the cost of repairs is either omitted or underestimated. One noticeable feature of Mr. Hobart's tabulation is that there is no mention of steam consumption. Intentionally or otherwise, the steam-hoist builders have befogged the question by making a great point of the steam consumption of hoists. The operator is not at all concerned in steam consumption; it is the actual cost of operation that he is interested in, and it is a comparison between the cost of operation of the two systems, all factors being considered, that should determine the choice. The steam consumption, or its determination by test, is only one step in the problem of estimating the fuel consumption, which, in an actual installation, can be directly measured much more accurately, as was done by Mr. Hobart.

Jan 4, 1918