Search Documents

By M. E. Wadsworth, G. W. Warren

INTRODUCTION Hydrometallurgical processes for the extraction of metal values can be divided into two broad categories: (a) Processes involving the treatment of high grade material (e.g. finely divided mineral concentrates); and (b) processes which treat lower grade material (ores, waste dumps, etc.). This discussion will be directed primarily toward the first category, but in either case a fundamental knowledge of the intrinsic kinetics and thermodynamics is necessary to understand the behavior of the system. The bulk of research efforts in the last decade along these lines has been aimed at the recovery of copper (1-8). However much information has also been reported on uranium (9, 10) , zinc (11) , cobalt and nickel (12, 13). More comprehensive reviews on these areas are also available (14). As discussed by Sepulveda and Herbst (15, 16) one of the most difficult problems facing process designers is the acquisition and scale-up of reliable information concerning the intrinsic kinetics of leaching systems. The scale-up or modeling of these multiparticle systems is far more complex than that of homogeneous ones. This is due to the numerous rate determining steps which are possible with heterogeneous reactions and the broad distribution of properties of a multiparticle feed such as particle size and mineralogical composition (16). In addition, other factors must also be considered such as interactions between particles, the anisotropic nature of individual particles, the effect of solution chemistry, and electrochemical phenomena. All of these factors must be taken into account, often simultaneously. The thrust of this paper will be to more closely examine how the factors mentioned above can be treated. Some elementary examples of

Jan 1, 1980

By G. S. Ansell, J. Weertman

The creep behavior of an aluminum alloy hardened with a finely dispersed phase of aluminum oxide was investigated. The as-extruded alloy shows an approximate steady-state creep in which the creed rate depends exponentially on the applied stress. The activation energy of creeb is abbroximately 150,000 cal per mole. The recrystallized alloy shows no steady-state creep. ONE method of improving the creep resistance of a metal is to introduce a finely dispersed second phase into the metal matrix. The improvement of the creep resistance has been qualitatively explained by assuming that the dispersed second-phase particles act as obstacles to dislocation motion. If the main effect of second-phase particles is simply to hinder dislocation motion then it is possible to derive a high-temperature creep equation for a dispersion-hardened alloy in a straightforward manner. In the Appendix of this paper such an equation is derived from a creep model which works very well for pure metals. Recently, F. V. Lenel has fabricated, for the first time, powder extrusions of aluminum-aluminum oxide in a large-grained recrystallized form. This alloy, designated as MD 2100, consists of a fine dispersion of aluminum oxide plates in a matrix of commercial purity aluminum. A considerable amount of investigation has been carried out concerning the microstructure and physical properties of this alloy.&apos; ) The aluminum oxide is present in the form of flakes 130A units thick and 0.3 u on edge. They are dispersed in the aluminum matrix with an average spacing of approximately 0.5 jx. The spacing varies in the range of 0.05 to 1.5 µ. The alloy structure is extremely stable at high temperatures. For this reason the alloy offers a unique opportunity for a fundamental study of creep of a very finely dispersed two-phase alloy. Lenel supplied specimens in both the unrecrystallized and recrystallized condition. This paper reports high-temperature creep experiments carried out on these specimens. The results obtained were rather unexpected. No steady-state creep was observed in the recrys-tallized material. In fact, after some transient creep which takes place upon loading, the creep rate is essentially zero ( < 10-8per min). If the second-phase particles acted solely as obstacles to the motion of dislocations, measurable steady-state creep would be expected. Since none is observed it appears that the main effect of the fine dispersion in the recrystallized material is to inactivate the dislocation sources themselves, rather than hinder the motion of dislocation loops created at these sources. EXPERIMENTAL DETAILS Specimens were tested in wire form, 0.087 in. in diam for the as-extruded alloy, and 0.035 in. in diam for the recrystallized alloy. These samples were held in friction-type wire grips; a gage length of 2.5 cm was used for all the creep tests. The specimens were held at 600°C in the test apparatus for at least 15 hr prior to each test. The tests were run under the condition of constant loading and, since the creep strains were small, can be considered as constant stress tests. The temperature of testing was held constant within 3°C. Elongations were measured with an optical cathetometer which was capable of measuring strains as smaIl as 0.00012. This allowed the measurement of strain rates as low as l0-8&apos;per rnin. In addition to the creep tests optical micrographs were made in order to determine both the grain size and microstructure of these materials. RESULTS Fig. 1 shows a few typical creep curves obtained from the as-extruded material. The elongations were somewhat erratic, but each curve shows a region of quasi-steady-state creep from which an approximate steady-state creep rate can be obtained. In general the higher the stress at a given temperature, the greater the total elongation before fracture. The lower the applied stress, the longer is the region where the creep rate is almost constant. Summary data from the creep tests of the as-extruded material are listed in Table I. The steady-state creep data of the as-extruded material for a range of stresses at a constant temperature follow a creep equation of the type creep rate = K&apos; = A exp (&) [11 where A and B are constants, k is Boltzmann&apos;s constant, T is the absolute temperature, and a the stress. The standard error of estimate of the data received is less than one order of magnitude. As shown in Fig. 2, if one compensates the creep-rate data for the effect of temperature over the range of test temperature, the steady-state creep data roughly follow a creep equation of the type Temperature compensated creep rate = K* = A exp

Jan 1, 1960

By Oliver C. Ralston

A definite field of usefulness has developed for the brine-leaching processes of removing lead from ores and other products, so this paper reviews the developments, both in practice and in research, that have taken place since the publication of two earlier papers on this subject.&apos; Several commercial plants are now in operation and a number of semi-commercial test plants have been operated in an effort to determine the limitations of brine leaching and to compare the results with other forms of treatment. Briefly, the brine leaching of lead depends on the fact that lead chloride and lead sulfate are soluble in saturated sodium-chloride solutions. In dilute brines, the solubility of the lead salt is less than in pure water; but in the strong brines, the solubility is greater than in pure water due, supposedly, to the formation of a double sodium-lead chloride. This is seen in Fig. 1, which shows the results of M. Demassieux2 on the solubility of lead chloride in sodium-chloride solutions of different concentrations and at three temperatures. The curves are not those given by Demassieux but are calculated from his results in order to convert them to units common in metallurgical work. The right-hand branch of each curve shows that if the solution is kept in contact with solid sodium chloride the lead chloride can be almost entirely displaced from solution, but that brines which are saturated with sodium chloride, but are not in contact with the solid salt, have a very high solubility for lead chloride. The diagram gives the analysis of the solution in grams of lead per liter, although the substance actually in solution is lead chloride. At 100" C. as much as 100 gm. of lead per liter can be obtained; but at lower tem-

Jan 1, 1924

By R. M. Brick, R. G. Treuting

DESPITE the basic importance of slip in the plastic deformation of metals, and the considerable experimental investigation, thought, and speculation that have been devoted to the fundamental nature of these processes, surprisingly few data have been reported regarding the microscopic appear- [ ] ance and distribution of slip lines,[$] the external manifestation of the slip process. Photographs hitherto reproduced in the literature are in general at low or unspecified magnifications with no correlation to the prior shear. A single-crystal cylindrical tensile specimen of alpha brass about ½ in. in diameter, one of many previously prepared by H. L. Burghoff,1 was available for study. A plane about 3/16 in. wide, parallel to the specimen axis and normal to the plane containing the slip direction and the specimen axis, was ground and metallographically polished along the entire 5-in. gauge length. Heavy etching produced a surface free of both scratches and flow. The specimen was strained in tension until slip markings first became visible on the polished surface (Figs. I and 2). Restressing the crystal caused additional markings to appear at an initially lower [ ] stress than previously was required. Stretching the specimen to produce a dense concentration of slip lines caused such variations in level in the polished surface (normal to the slip direction) that microscopic study at higher magnifications became impossible. After annealing 15 hr. at 850°C., the specimen recrystallized to form two grains with a boundary approximately normal to the specimen axis and about midway along its length. Each was X-rayed, and two planes were again polished along the length of the specimen, in this case each parallel to the slip direction in one of the two crystals. A light longitudinal scratch parallel to the specimen axis was drawn down the center of each plane. A Huggenberger extensometer was attached to the crystal A, whose slip plane would have the higher resolved shear stress of the two, and the specimen was again strained in tension.

Jan 1, 1941

By P. Pollard

A method has been developed for evaluating acid treatments in fractured limestone fields by breaking down pressure drawdown into three component parts: (I) pressure differcntial across "skin" near the borehole face, (2) pressure differential due to flow resistance in the coarse communicating fissures and (3) pressure differential between the fine voids and the coarse fissures. It is apparent that in most successful acid treatments the first term, skin resistance, has been reduced or eliminated. Further, it is often possible to estimate the volume of coarse fissures associated with the second term, coarse fissure flow resistance. In cases where this volume is comparable with practical acid volumes it seems likely that this resistance also may be attacked with a suitably retarded acid. INTROD UCTION Acid treatment has been successfully applied as a general practice in the limestone wells in the Mara/ Maracaibo districts of Venezuela for some 10 years. At the same time the need has been felt for a more precise method of: (1) evaluating the effect of an acid job and (2) selecting wells which should benefit from an acid treatment. The following method, based on an analysis of build-up curves for wells producing from fractured limestone, provides a means of forecasting the effect acid will have on a well and in many cases the probable order of production rate increase which may be expected. In certain cases it is also possible to calculate the fissure volume through which the acid has to be displaced for best results. Various approximations are introduced in the method, but within the limitations of these the analysis gives an indication of how a well, whether previously acidized or not, may be expected to respond to acid treatment. Suitable build-up curves cannot be obtained on "tight" wells which do not give sustained production and the method is not applicable to such wells. Figs. 1 through 7 illustrate various types of build-up curves obtained from limestone wells in Western Venezuela. Curves are included showing (1) both skin and coarse fissure resistance, (2) skin resistance only, (3 and 4) reduction of skin resistance by acidization, (5) fissure resistance only, (6) reduction of coarse fissure resistance by acidization, and (7) acidization failure. This theory has been successfully applied for over three years during which 22 acid treatments have been carried out specifically to reduce skin resistance and three treatments to reduce coarse fissure resistance. The method has been found to be a useful aid in the selection of wells for acidization.

W. H. BASSETT,* Waterbury, Conn. (written discussion ?).-The effect of reducing gases on hot solid copper has been known for many years in the copper industry, and precautions taken to guard against it in the general practice in copper heating and annealing. In view of the statement that Bengough and Hill, in 1910, were the first to suggest the possibility of the formation of gas within the copper itself, it is interesting to note that in Harper&apos;s Magazine for April, 1904, an article, "Life and Diseases of Metals," by Professor Heyn, illustrated the effect of reducing gases on copper by a photograph, which is shown in Fig. 1. This he entitled "Copper burst asunder by disease." After referring to the effect of hydrogen on steel, he makes the following remark: "Similar symptoms of poisoning, caused by hydrogen or gases containing hydrogen (as gas for lighting purposes), are apparent in copper when exposed to red heat. Not every kind of .copper is susceptible to this poisoning in equal degree. Copper per-fectly free of cuprous oxide is entirely exempt from poisoning. Most of the various coppers of commerce, however, contain cuprous oxide, formed during the smelting process while exposed to atmospheric influences. In such coppers, containing cuprous oxide, hydrogen causes a terrible disease on the copper being heated red hot. The copper bursts asunder and is permeated by cracks. This disease is practically incurable and can be eradicated by resmelting only. The results work destructively according to the amount of cuprous oxide contained in the copper." It must have been evident to Professor Heyn, as it was to us on reading this article, that the bursting asunder of the copper was clue to the formation of steam. Practical copper heaters have known for many years that it was quite possible to produce blisters, or large gas holes, in the interior of copper plates or bars by heating to a high temperature in reducing gases. These facts, of course, do not detract from the value of the study of the action of hydrogen gas that has been made by Mr. Pilling, but simply illustrate that the practical effect of reducing gases on furnace-refined copper has long been a troublesome factor in the heating or annealing of that metal.

Jan 1, 1919

By George F. Comstock

It has been known for many years that the alloy containing 90 per cent. copper and 10 per cent. aluminum can be hardened, like steel, by quenching from a suitable temperature, and that the hardened alloy can be softened again by annealing or drawing the temper. It does not seem to be generally appreciated, however, that the effect of the first slight reheating after quenching is actually increased hardness, the softening effect not taking place until a certain temperature of "drawing" has been exceeded. This paper gives the results of a few experiments on various specimens of cast 10 per cent. aluminum bronze, quenched for maximum hardness, and subsequcntly annealed at different temperatures. The hardness measurements were made with both a scleroscope and a standard Swedish Brinell machine; some peculiarities of the scleroscope test on this material are described. The author is not aware of many previous investigations of the hardness of this alloy when quenched and drawn, but two important papers on the subject should be mentioned. The earliest was by Portevin and Arnou,1 in which it was stated that tempering quenched 10 per cent. aluminum bronze at 400" C. increased the hardness as compared with the quenched untempered alloy and that reheating above that temperature &apos; was necessary to obtain any softening effect. A later paper was by Seidell and Horvitz,2 who mentioned Portevin and Arnou&apos;s work, but did not report any increase in hardness obtained

Jan 1, 1925

By Dae S. Young

A new probabilistic approach is introduced for slope stability analysis including adverse impact of blasting vibrations. The material strength within a slope area is randomized in this bi-variate joint probability analysis. To be a completely general engineering method, the new probabilistic approach employs the random variable transformation technique: the Hermite model of the Gaussian transformation function, which transforms the experimental histogram of strength values to the standard Gaussian variables. Because bi- normal joint probability is analyzed on the true probability region projected on the Gaussian transformed variable plane, it is an exact solution of slope stability based on the available sample data. Details of the probabilistic approach are given through a case study on an iron ore mine. The case study demonstrated that the probabilistic approach is effective and simple enough to be a routine engineering practice for slope analysis.

Jan 1, 1984

[Note.—The paper of Mr. Hoffman on " Practical Results in the Magnetic Concentration of Iron-Ore " (page 602); that of Mr. Langdon on "The Use of Magnetic Concentrates in the Port Henry Blast-Furnaaces" (page 599); and those of Mr. Landis on "The Determination of Iron in the Tails from Magnetic Concentration " (page 609) and "Note on Sampling Iron-Ore" (page 611), were all prepared as contributions to this discussion.] The papers of Mr. Langdon and Mr. Hoffman were presented. W. H. Hoffman, Croton Mines, N. Y.: I will add a few remarks, by way of answer to inquiries for further details. The Croton Mines are particularly well located for cheap mining. The ore-bed is very large, and so lies in relation to the railway tracks of the Harlem and other railroads that a very large proportion of our mining for several years to come can be done above these tracks. The concentrating-mill is now 400 feet from where we are working in the quarry. In blasting we never remove less than 2500 tons at a blast,

Jan 1, 1892

By Theodore Simons

During the last half century a great amount of ingenuity and energy has been devoted to the invention of appliances for the recovery of valuable minerals from very fine sands and slimes. The reason for this is that in almost every dressing plant the greatest losses of values, considered relatively as well as absolutely, occur in the treatment of slimes. The natural aim of mill operators to minimize these losses has in recent years received another impetus, from the fact that the gradually diminishing occurrence of high-grade ores makes a more intense recovery of values from existing resources absolutely necessary for profitable operation. The results of such attempts are found in the appearance of a great number of machines and appliances which make it profitable to-day to rework old clumps, containing the tailings of older processes. A constantly growing difficulty of obtaining skilled labor and the increase in wages made it prohibitory to employ those types of machines which required much attention, and in the middle of the ninieteenth century the various concentrating tables of the percussion type, which automatically discharge their products, began to take the place of the intermittent tables, on which, when the bed had reached a certain thickness, operation had to be stopped in order to allow the skimming by hand of the separate layers formed on the table. In the course of years, two general types of machines evolved for the treatment of fine sands arid slimes: The so-called concentrators and vanners, on the one hand, and the buddles and round tables on the other.&apos; For the profitable treatment of the very finest slimes, round tables have as a last resort proved more satisfactory and econoillical than other machines. In recent years they have agaiu become the subject of close inves-

Jan 1, 1914

By K. M. Kolobova, E. Z. Kurmayev, A. Z. Menshikov, S. A. Nemnonov, V. A. Trapeznikov

The present work represents a review of our intestigations into the X-ray spectra of solids, which have been carried out by us along two lines of upproach: 1) St@ of the electronic structure of high -rnelting compounds of transition metals; 2) stzddy of the interatomic binding forces by the fine structure of absorption spectra under varying temperature and concentration conditions. With this in mind, int>estigations hare been made into the emission and absorption spectra of the K-series of atoms of transition elements in alloys and compounds. In the problem concerned with the electronic structure of high-melting compounds of transition metals, considerable importance is attached to the question of ascertaining the role played by 3d4sp electrons of metal and 2p electrons of metalloid in the formation of chemical bonds and of giving, on the strength of this data, an explanation of the properties which seem to be contradictory at first sight: good conductivity inherent in metals and high brittleness and high-melting characteristics typical of covalent compounds. Over the last few decades this question has attracted the attention of many investigators whose studies were devoted to this type of compound. Many works, both of theoretical1-3 and experimental4- l5 nature , have contributed much to the elucidation of the physical character of the phenomenon referred to. Alongside the investigations in the field of electric resistance, Hall effect, paramagnetic susceptibility, electronic heat capacity, and the temperature of transformation into a superconducting state, we should particularly emphasize the studies on X-ray spectra, which have played a significant role in the development of the zonal theory for high-melting compounds. This fact has become highly evident after the theoretical calculation of the energy spectrum has been made and the density of states curve in Tic, TiN, and Ti0 has been plotted by Ern and Switendick3 who used the method of augmented plane waves. Correlation of the results of the theoretical calculation of the band structure in the compounds listed above with the data obtained by X-ray spectroscopy studies showed that X-ray spectra can be a source of valuable information on the electronic structure of high-melting compounds within a wide range of ener- gies. It is well known that X-ray emission spectra basically give a direct picture of the occupied excited states above the Fermi level of a solid (valence band, conduction band) and that the absorption spectra (region of initial absorption) give a similar picture of states corresponding to the unoccupied levels near the Fermi surface. Full information on the density distribution of electronic states by energies can be obtained by combining the emission and absorption spectra. Such an opportunity arises from investigation

Jan 1, 1970

By S. C. Oliphant, R. Floyd Farris

Presented in this paper is a summary of the results of experiments conducted in both the laboratory and the field during the past three years in connection with casing-perfora. tion problems. Included are studies of gun features that influence bullet performance and penetration, and studies of the effect of perforator bullets on casing and the neat cement in the annulus. Discussion and data are also presented relative to the accuracy of depth measurements in deep wells. Introduction It is a common practice in the oil industry to effect the completion of oil wells by setting and cementing casing through the producing horizons and perforating the section of casing opposite the desired interval by means of a gun lowered into the well on a cable or on the tubing. This practice has been followed for some time, and this method of completion has been given considerable study by the companies that render perforating service as well as by the oil companies that utilize their services. Through continued research on this subject, it has been possible to develop guns, bullets, and powder that will permit controlled firing at great depths, and penetration of as many as two strings of casing. It is the object of this paper to present the results of studies made of gun perforating in both the field and the laboratory. These studies were made to determine the factors that affect penetration of the bullet, burring of the casing, accuracy of depth measurements, and other items. It is hoped that by presenting the results of these investigations a better understanding may be obtained of certain of the factors involved in gun perforating and further investigation of the subject will be prompted. Subsurface Tests A well approximately 9000 ft deep, which was being prepared for abandonment, was selected for subsurface tests of gun-perforating experiments, In preparing the well for the experiment, 51/2-in. casing in the hole was pulled and racked in the derrick. A test section of pipe, which consisted of 65 ft of 5-in. 18-lb J-55 casing centered inside 7-in. 28-lb N-80 casing, was placed in the derrick corner and the annulus between the two pipes was cemented from the bottom up with 161/2 lb per gal neat cement, which was mixed and displaced with a cementing truck in the usual manner. After the cement had been allowed to harden for about a week, the test section was lowered into the hole on the 51/2-in. casing to a depth of 6600 ft by casing measurements. The hole was filled with drilling fluid weighing 10 lb per gallon. A perforating company was called to perforate the pipe, but was not advised that an experiment was being conducted. The company was asked to check the total depth (to cross pins in the bottom of the test section), then to raise the gun a given distance and fire a given number of shots with 1/2-in. bullets, pick up another distance and fire a given number of 3/8-in

Jan 1, 1947

By S. C. Oliphant, R. Floyd Farris

Presented in this paper is a summary of the results of experiments conducted in both the laboratory and the field during the past three years in connection with casing-perfora. tion problems. Included are studies of gun features that influence bullet performance and penetration, and studies of the effect of perforator bullets on casing and the neat cement in the annulus. Discussion and data are also presented relative to the accuracy of depth measurements in deep wells. Introduction It is a common practice in the oil industry to effect the completion of oil wells by setting and cementing casing through the producing horizons and perforating the section of casing opposite the desired interval by means of a gun lowered into the well on a cable or on the tubing. This practice has been followed for some time, and this method of completion has been given considerable study by the companies that render perforating service as well as by the oil companies that utilize their services. Through continued research on this subject, it has been possible to develop guns, bullets, and powder that will permit controlled firing at great depths, and penetration of as many as two strings of casing. It is the object of this paper to present the results of studies made of gun perforating in both the field and the laboratory. These studies were made to determine the factors that affect penetration of the bullet, burring of the casing, accuracy of depth measurements, and other items. It is hoped that by presenting the results of these investigations a better understanding may be obtained of certain of the factors involved in gun perforating and further investigation of the subject will be prompted. Subsurface Tests A well approximately 9000 ft deep, which was being prepared for abandonment, was selected for subsurface tests of gun-perforating experiments, In preparing the well for the experiment, 51/2-in. casing in the hole was pulled and racked in the derrick. A test section of pipe, which consisted of 65 ft of 5-in. 18-lb J-55 casing centered inside 7-in. 28-lb N-80 casing, was placed in the derrick corner and the annulus between the two pipes was cemented from the bottom up with 161/2 lb per gal neat cement, which was mixed and displaced with a cementing truck in the usual manner. After the cement had been allowed to harden for about a week, the test section was lowered into the hole on the 51/2-in. casing to a depth of 6600 ft by casing measurements. The hole was filled with drilling fluid weighing 10 lb per gallon. A perforating company was called to perforate the pipe, but was not advised that an experiment was being conducted. The company was asked to check the total depth (to cross pins in the bottom of the test section), then to raise the gun a given distance and fire a given number of shots with 1/2-in. bullets, pick up another distance and fire a given number of 3/8-in

Jan 1, 1947

By C. O. Brawner

FACTORS THAT INFLUENCE STABILITY AND STABILIZATION METHOD The most effective stabilization method and design can only be developed if the cause(s) and mechanics of the slide are known. Therefore, it is important that the stability be evaluated by an engineer who has had extensive rock stability experience. The most important factors that influence stability are structural geology, ground water, blasting and the mining method or methods. Structural Geology - The majority of failures in rock slopes occur along discontinuities in the rock (joints, bedding planes, shear or fault zones, etc.). Therefore, on all surface mining projects, the development and maintenance of a comprehensive structural geologic mapping program should be a first priority program that is considered a part of the operations function. This program should include mapping all major features - faults, shear zones and through going joints. All structural features which could influence stability should be mapped and presented in a structural domain format for the entire mine (Canmet, 1977). Where planes, wedges or blocks will be undercut by the mining excavation, shear strength and strain to failure tests should be performed on the joints, fault gouge and gouge-rock contact surfaces. These tests must be performed on the samples in the direction of potential slide movement and must determine the range of peak and residual shear strength values. A preliminary assessment of friction angle can be obtained from measurements of failed surfaces in the field (Figure 1) or from core sliding tests (Barton, 1981). An assessment must be made of the past geologic history of

Jan 1, 1983

By Harry H. Power

While the attention of all engineering branches is focused today on changes and improvements in the several curricula, we are concerned here with the many questions arising in industry and college concerning the preparation for the petroleum engineering profession. The succession of problems confronting the petroleum engineer demands a degree of versatility not ordinarily encountered in other professions. As a consequence, the student cannot acquire mastery of all the several engineering branches represented in field practice, and as an alternative, he has learned to appreciate the value of thorough training in the basic or fundamental sciences as a Preliminary foundation for professional work. While our attention is directed primarily to the training of engineers in educational institutions, it is necessary that the ultimate education of the professional engineer be kept in mind. It is apparent that his success as an engineer is limited not only by his educational and job experience, but by his native endowments: mentality, Personality and health. The engineer&apos;s lack of job experiences often proves as much a handicap as the lack of adequate college training. If the final product proves to be satisfactory, both industry and technical institutions are to be congratulated. However, if the Product is found wanting, the one most responsible should For the most part, students of engineering colleges have had their interests in applied science awakened at a relatively early age. Manyof them entered college as a convenient means of acquiring a technical education, but undoubtedly would have had better prospects in a shorter program offered by institutions of non-college grade. The activating motive of practical interest is also strong in students suitable for college training, but in many cases an intellectual interest must be awakened in order that it may survive graduation. Numerous engineers believe that this progressive process of selection and determination of career aims is one of the essential services rendered by the engineering colleges. Industrialists, who are more inter. ested in quality than quantity of petroleum engineering graduates, have pointed out the good that should result if more emphasis were given to the work of eliminating the misfits. They also point out the protective measures that have been taken by other professions for the betterment of professional standards. Mention has been ,de of the beneficial results to be obtdned by collective determination of the market for the products of engineering schools, particularly in that the students unsuited to the profession would have an opportunity to prepare themselves for employment more suited to their personalities and other qualifications. In the event that such a system of coordinated personnel direction is developed by the

Jan 1, 1941

By Harry H. Power

While the attention of all engineering branches is focused today on changes and improvements in the several curricula, we are concerned here with the many questions arising in industry and college concerning the preparation for the petroleum engineering profession. The succession of problems confronting the petroleum engineer demands a degree of versatility not ordinarily encountered in other professions. As a consequence, the student cannot acquire mastery of all the several engineering branches represented in field practice, and as an alternative, he has learned to appreciate the value of thorough training in the basic or fundamental sciences as a Preliminary foundation for professional work. While our attention is directed primarily to the training of engineers in educational institutions, it is necessary that the ultimate education of the professional engineer be kept in mind. It is apparent that his success as an engineer is limited not only by his educational and job experience, but by his native endowments: mentality, Personality and health. The engineer&apos;s lack of job experiences often proves as much a handicap as the lack of adequate college training. If the final product proves to be satisfactory, both industry and technical institutions are to be congratulated. However, if the Product is found wanting, the one most responsible should For the most part, students of engineering colleges have had their interests in applied science awakened at a relatively early age. Manyof them entered college as a convenient means of acquiring a technical education, but undoubtedly would have had better prospects in a shorter program offered by institutions of non-college grade. The activating motive of practical interest is also strong in students suitable for college training, but in many cases an intellectual interest must be awakened in order that it may survive graduation. Numerous engineers believe that this progressive process of selection and determination of career aims is one of the essential services rendered by the engineering colleges. Industrialists, who are more inter. ested in quality than quantity of petroleum engineering graduates, have pointed out the good that should result if more emphasis were given to the work of eliminating the misfits. They also point out the protective measures that have been taken by other professions for the betterment of professional standards. Mention has been ,de of the beneficial results to be obtdned by collective determination of the market for the products of engineering schools, particularly in that the students unsuited to the profession would have an opportunity to prepare themselves for employment more suited to their personalities and other qualifications. In the event that such a system of coordinated personnel direction is developed by the

Jan 1, 1941

By Charles E. Locke

PROSPERITY of the gold miner has continued with attendant construction of numerous plants, many of them small but some of good size. Many new mills have been erected in Canada and in the Philippines, end one should mention the new mill at Cripple Creek, Colo., a custom plant allowing a choice of flotation, cyaniding, or roasting and cyaniding. Flotation is a feature of many of the new plants and some existing mills have been remodeled to use flotation in place of amalgamation and cyaniding. The Utah Copper Co. has re- opened its Arthur mill and operations are being resumed in the big Ray, Chino, and Inspiration copper mills. Examples of new construction are the Mountain City 300-ton copper flotation mill in northern Elko County, Nevada; the Star zinc mill and one or two other mills in the Coeur d&apos;Alene district of Idaho; and the 500-ton mill for the Buena Vista mine at Stewart, B. C. The last-named is to be installed underground, following the example of the zinc mill at Gilman, Colo., and he small Doyle jigging plant in the Wisconsin zinc fields.

Jan 1, 1937

By James Douglas

The Copper Queen mine was opened in 1880 by Messrs. Martin, Ballard & Reilly, and the first copper-furnace was blown-in on August 20th of that year. Prior to that summer nothing but prospect-work had been done on the copper Queen and on a number of adjacent claims. In fact, it was a small deposit, not of copper-ore, but of cerussite, which still remains undeveloped, on the western slope of the Queen hill, which

Jan 1, 1900

By Helmut Thielsch

During the last three decades a great many arguments have been presented on the subject of "mosaicJ&apos; or "blockJJ structures of metals. Apparently because of insufficient evidence, the "block-structure" theories have never been widely understood among the physical metallurgists in this country, and most investigators among the few that have tried to demonstrate the existence of such an inner strutture Of crystals or grains have failed to recognize also the existence of a lamellar structure. Moreover, little thought has been given to justify the existence of such "lamellar" or "mosaic-block" structures on a theoretical basis. Since properties such as Plasticity; ferro-magnetism, hardness, diffusion, and others may be explained by structural faults in the lattice network of the crystals: the great importance of a more detailed knowledge of the structure within crystals or grains becomes now evident. Because Of the vast extent of the field Of submicroscopic structures, it shall be the purpose Of this paper only to review the more important of the results obtained by other investigators, especially in Germany, where a great deal of attention has been given to mosaic structure during the last three years. The origin of this mosaic patternt and effects of cold reduction and recrystallization will be shown in further studies later on. Imperfections in Crystals The many terms used in the literature to denote structural types of crystals are often not clearly defined. To clear up some of the confusion, the meaning of the more important terms will be given here. ideal, or perfect without any structural imperfections are called "ideal crystals,,or &apos;&apos;Perfect&apos;&apos; crystals,n meaning a Homogeneous interior structure of atoms, ions or molecules, as the case may be. In other words, at every point in the interior of the crystal exactly the same orientation of the crystallographic axes of the coordinate system would exist. The Surface of such a body, if etched with an appropriate etching reagent, would reflect light with perfect uniformity. Crystals of this type are almost nonexistent. Real Crystals.—L&apos;Real crystals"&apos; may contain various types of structural defects, which can be classified into: (I) lineage structure, (2) mosaic-block structure, (3) lamellar structure. The inhomogeneities many,in these groups mean that the orientation of the crystallographic aies will not be the same at every point within the interior of a crystal (or grain of a poly crystalline body). &apos;Perjecl Real Crystals.—The term "perfect real crystals " is generally used to describe crystals with minute structural or thermo-dynamical inhomogeneities. The former

Jan 1, 1946

By Helmut Thielsch

During the last three decades a great many arguments have been presented on the subject of "mosaicJ&apos; or "blockJJ structures of metals. Apparently because of insufficient evidence, the "block-structure" theories have never been widely understood among the physical metallurgists in this country, and most investigators among the few that have tried to demonstrate the existence of such an inner strutture Of crystals or grains have failed to recognize also the existence of a lamellar structure. Moreover, little thought has been given to justify the existence of such "lamellar" or "mosaic-block" structures on a theoretical basis. Since properties such as Plasticity; ferro-magnetism, hardness, diffusion, and others may be explained by structural faults in the lattice network of the crystals: the great importance of a more detailed knowledge of the structure within crystals or grains becomes now evident. Because Of the vast extent of the field Of submicroscopic structures, it shall be the purpose Of this paper only to review the more important of the results obtained by other investigators, especially in Germany, where a great deal of attention has been given to mosaic structure during the last three years. The origin of this mosaic patternt and effects of cold reduction and recrystallization will be shown in further studies later on. Imperfections in Crystals The many terms used in the literature to denote structural types of crystals are often not clearly defined. To clear up some of the confusion, the meaning of the more important terms will be given here. ideal, or perfect without any structural imperfections are called "ideal crystals,,or &apos;&apos;Perfect&apos;&apos; crystals,n meaning a Homogeneous interior structure of atoms, ions or molecules, as the case may be. In other words, at every point in the interior of the crystal exactly the same orientation of the crystallographic axes of the coordinate system would exist. The Surface of such a body, if etched with an appropriate etching reagent, would reflect light with perfect uniformity. Crystals of this type are almost nonexistent. Real Crystals.—L&apos;Real crystals"&apos; may contain various types of structural defects, which can be classified into: (I) lineage structure, (2) mosaic-block structure, (3) lamellar structure. The inhomogeneities many,in these groups mean that the orientation of the crystallographic aies will not be the same at every point within the interior of a crystal (or grain of a poly crystalline body). &apos;Perjecl Real Crystals.—The term "perfect real crystals " is generally used to describe crystals with minute structural or thermo-dynamical inhomogeneities. The former

Jan 1, 1946