Search Documents

By L. A. Willey

IN 1953, a method for filtering a liquid phase from solid phases while in equilibrium at elevated temperatures was devised at the Alcoa Aluminum Research Laboratories. Since then, it has been applied to the investigation of liquid-solid equilibrium in metallic systems. In application, the method simplifies the centrifuge filt.ration procedure as developed by Scheil and described by Gebhardt Fig. 1 shows a sketch of the filtering apparatus located within a thermal analysis furnace. It consists of a stainless steel filter crucible A, into the bottom of which a porous carbon filter disk B, 1 3/4 in. diam by 1/4 in. thick, is sealed to the shoulder and rim with carbonaceous cement. The base of the filter crucible, machined to an angle, fits into a tapered seat at the mouth of a stainless steel vacuum chamber C. A connecting tube from the vacuum chamber to a vacuum line also serves as a means for supporting the apparatus from the base of the furnace. An alundum crucible D of 25 ml capacity is placed with- in the vacuum chamber below the filter for collecting the filtrate. Two thermocouples E, in stainless steel protection tubes, which extend from 1/16 to in. above the center of the filter, are mounted on the rim of the filter crucible. One thermocouple is used in differential connection with the furnace control thermocouple to regulate rates of heating and cooling. The other serves as a means for recording the temperature of the alloy prior to filtering. A suitable mold coating is used on exposed surfaces of stainless steel parts to guard against attack upon these parts as well as to avoid contamination of the alloy samples. A mold wash prepared from precipitated CaCO, is suitable for aluminum alloys. The porous carbon for the filter disks and the carbonaceous cement, grade 200 (graphite base), were obtained from the National Carbon Co. Porous car-bon, grade Nos. 10 to 60, has been employed. Grade No. 40, however, appeared to give the optimum advantages in operation. In operation, an alloy sample is remelted and heated to about 50°C above its liquidus temperature. At the same time, the filter apparatus is preheated to about the same temperature. The alloy then is cast into the filter crucible.

Jan 1, 1957

By Hansheinz Portisch, Harold Margolin

A surface expansion was found to occur sometime after etching in Ti-A1 alloys containing 9.5 to 12.5 wt pct Al. The structure formed, grew, and disappeared with tzrrze. The surface expansion was followed by microscope observations and interferometric and lattice parameter measurements. Activation energy measurements for the growth of the "expansion structure" and chemical analysis indicated that the phenomenon occurred as a result of hydrogen pzckup during etching. It is proposed that hydrogen initially enters octahedral sites of Ti3Al coherent with a Ti and later shifts to the tetrahedral sites. It is postulated that expansion occurs when hydrogen enters the tetrahedral sites. The expansion structure disappeared, it is proposed, because of diffusion of hydrogen from the surface into the body of the alloy and because of loss of coherency of Ti3Al. In examining Ti-A1 alloys, Ence and arolinl observed markings on the surface of specimens. These markings did not appear after electropolishing only, but rather appeared only after etching. The markings appeared to grow as a function of time after etching and later seemed to disappear. Although the markings had some similarity to precipitates, showing, frequently, a Widmanstatten type of arrangement, the observation that other microstructural markings continue to be seen within the new structure suggested that it was actually not a precipitate. The source of this structure was unknown and an attempt was made in the present investigation to develop some understanding of its nature. It has been labeled expansion structure. 1) EXPERIMENTAL PROCEDURE A) Alloys. Alloys in the range 6.5 to 14.5 wt. pct A1 were studied. Bars, 4 in. sq, forged from Bureau of Mines (73 Bhn) titanium consumably arc-melted 4-lb ingots,' as well as 50-g arc-melted buttons of desired aluminum contents were used. The 50-g buttons also used Bureau of Mines titanium (73 Bhn) and aluminum of 99.99 pct purity. Buttons containing up to 8.5 wt pct A1 were hot-rolled from a furnace at 900' . Those with higher aluminum contents were hand-forged on a titanium anvil, and heated with an oxygen-hydrogen torch in the region of 1200" to 1300°c. Frequent reheating kept the samples at the desired temperature range. After a reduction of about 30 pct, the samples were water-quenched. To eliminate any contamination picked up either during hot rolling or forging, at least 1 mil of the surface of the sample was taken off. B) Heat Treatment. Prior to heat treatment all alloys were vacuum-annealed to remove hydrogen. Samples were annealed at 900' until a vacuum of 10'5 mm Hg was established. After this treatment, the samples were wrapped in molybdenum sheet and heat-treated in argon-filled quartz capsules, which were broken under water or iced brine at the conclusion of the heat treatment. All heat treatments under dynamic vacuum were performed in a rapid-quench furnace. This consisted of a molybdenum-lined quartz tube attached to a vacuum system and through a stopcock to a beaker of water. At the completion of the heat treatment the vacuum stopcock was closed, the furnace shut off, and dropped below the quartz tube. Then immediately the inlet stopcock was opened and water admitted until the tube was filled. The steam formed was allowed to escape through the inlet stopcock. This method was used in heat treatments up to llOO°C. C) Metallography. Specimens for metallographic examination were ground, then electropolished using a Disa Electropol machine with a perchloric acid electr01te. Specimens were etched with R-etch.3 A standard etching time of 3 min was used, with the specimen being agitated during immersion. D) Sample Preparation for X-ray Analysis. Samples 0.2 to 0.5 mm in diam were produced from heat-treated rods which were turned to 2 mm diam on a lathe and then rotation-etched. An etchant consisting of 1 pt HF, 7 pt HN03, and 12 pt HzO was satisfactory. With the rod rotating in a vertical position at 50 to 100 rpm, a needle with uniform dimensions could be obtained. Care had to be taken to insure that the rod was at the center of rotation, otherwise cavitation developed. If a small unevenness developed, it was possible to grind it off with a fine emery paper. E) X-ray Diffraction. All X-ray work was done on a North American Phillips X-ray diffraction apparatus and a Jarrell Ash microfocus X-ray unit. The Phillips unit was used with a copper target and nickel filter. The Jarrell Ash unit was fitted with a cobalt target and iron filter. For the Phillips unit 35 kva and 20 ma were used, whereas for the microfocus unit with the 100-p fixed-focus gun 40 kv and 1.5 ma were used. It was found that alignment of cameras on the Jarre11 Ash unit was very critical. The X-ray beam contains an intense area which is not the beam center. The cameras were aligned with the intense region by monitoring the beam coming out of the camera with a Geiger counter. Adjustments were made until a maximum intensity was obtained. A Phillips diffractometer with a Brown chart recorder furnished some of the lattice parameter data. The divergence slit up to 80 deg 28 was I deg; above 80 deg, a 4-deg opening was used, while the scatter slit was1 deg and the receiving slit had a 0.003-in. opening. The general scanning rate was 1 deg per min, while peaks of special interest were rescanned at -j deg per min. For elevated-temperature X-ray diffraction a Uni-cam High Temperature Camera with a film diameter

Jan 1, 1969

By W. C. Ellis, E. S. Greiner

METALLIC titanium has been prepared in small quantities since the beginning of the century. Hunter1 reported in 1910 that he obtained a malleable product of 99.9 pct purity by the reduction of the tetrachloride by sodium in a closed container. Later Van Arkel2 and Fast3 prepared small quantities of malleable titanium by thermal decomposition of titanium iodide. Another method for producing malleable titanium from tetrachloride was reported by Kroll4 who used magnesium as the reducing agent. More recently Dean, Long, Wartman, and Anderson5 working at the U.S. Bureau of Mines have reported the preparation of the metal on a pilot plant scale by the reduction of titanium tetrachloride by magnesium in an atmosphere of helium. Their product, which is malleable, was used in the present investigation. Early in 1948 after the work of this paper: was completed Campbell, Jaffee, Blocher, Gurland, and Gonser6 described the strength and working characteristics of pure titanium which was prepared by the iodide method on a scale producing 300 to 600 g per run, in the form of 0.3- to 0.4-in. diam rods. Their product is characterized by low hardness and large capacity for cold work which they attribute to a high degree of purity with respect to oxygen, nitrogen, and carbon. Titanium has a melting point of about 1725°C5 it may be classed as a light metal since the specific gravity is 4.5 g per cc-1. The crystal structure is close-packed hexagonal from room temperature t0 885°C. Above this temperature the structure is reported7 as body-centered cubic. The change in crystal structure has been associated with discontinuities in specific heat8 electric resistance9 and thermoelectric force10 at temperatures near 890°C. It is reported11 that annealed titanium has a tensile strength 0f 78,700 psi which can be increased by cold-work to 123,000 psi. In the present investigation, the lattice constants at room temperature, the thermal expansivity between 30 and 800°C, as well as the electrical resistivity and thermoelectric force against platinum between - 200 and 1000°C have been determined. MATERIALS For the measurements, two series of specimens were prepared from titanium furnished by the U. S. Bureau of Mines. The first was lade from an annealed sintered compact, 0.38 in. thick. Sections of the compact were cold-swaged with intermediate anneals in vacuum to the sizes used. Sizes over 0.25-in. diam were annealed at 1000°C and smaller sizes at 800°C. Specimens originating from the sintered compact are designated in this paper as A. The second series of specimens was lade from a rod of titanium, 0.19 in. in dial, which was cold-swaged with the necessary intermediate anneals to the required sizes. This series of specimens is designated B. The impurities in the specimens of titanium, determined by chemical analysis, are given in Table I. Oxygen and nitrogen which were not determined by analysis, are probably present although in small quantities in view of the ductility of the material.

Jan 1, 1948

By W. C. Ellis, E. S. Greiner

Metallic titanium has been prepared in small quantities since the beginning of the century. Hunter1 reported in 1910 that he obtained a malleable product of 99.9 pct purity by the reduction of the tetrachloride by sodium in a closed container. Later Van Arke12 and Fast prepared small quantities of malleable titanium by thermal decomposition of titanium iodide. Another method for producing malleable titanium from tetrachloride was reported by Kr0ll4 who used magnesium as the reducing agent. More recently Dean, Long, Wartman, and Anderson5 working at the U.S. Bureau of Mines have reported the preparation of the metal on a pilot plant scale by the reduction of titanium tetrachloride by magnesium in an atmosphere of helium. Their product, which is malleable, was used in the present investigation. Early in 1948 after the work of this paper was completed Campbell, Jaffee, Blocher, Gurland, and Gonser6 described the strength and working characteristics of pure titanium which was prepared by the iodide method on a scale producing 300 to 600 g per run, in the form of 0.3- to 0.4-in. diam rods. Their product is characterized by low hardness and large capacity for cold work which they attribute to a high degree of purity with respect to oxygen, nitrogen, and carbon. Titanium has a melting point of about 1725 C," it may be classed as a light metal since the specific gravity is 4.5 g per cc-I. The crystal structure is close-packed hexagonal from room temperature to 885°C. Above this temperature the structure is reported7 as body-centered cubic. The change in crystal structure has been associated with discontinuities in specific heat,8 electric resistanceg and theimoelec-tric force10 at temperatures near 890°C. It is reportedll that annealed titanium has a tensile strength of 78,700 psi which can be increased by cold-work to 123,000 psi. In the present investigation, the lattice constants at room temperature, the thermal expansivity between 30 and 800°C, as well as the electrical resistivity and thermoelectric force against platinum between — zoo and I000 C have been determined. Materials For the measurements, two series of specimens were prepared from titanium furnished by the U. S. Bureau of Mines. The first was made from an annealed sintered compact, 0.38 in. thick. Sections of the compact were cold-swaged with intermediate anneals in vacuum to the sizes used. Sizes over 0.25-in. diam were annealed at I000°C and smaller sizes at 800°C. Specimens originating from the sintered compact are designated in this paper as A. The second series of specimens was made from a rod of titanium, 0.19 in. in diam, which was cold-swaged with the necessary intermediate anneals to the required sizes. This series of specimens is designated B. The impurities in the specimens of titanium, determined by chemical analysis, are given in Table 1. Oxygen and nitrogen which Were not determined by analysis, are probably present although in small quantities in view of the ductility of the material.

Jan 1, 1949

TITANIUM is one of the most abundant elements in the minerals that make up the earth's crust but its use in industry is only a generation old; yet probably no other important commercial mineral raw material (except possibly magnesium) has undergone more changes and developments in sources of supply, in processing techniques, in uses and applications, in the past 10 years, or stands on' such a threshold of still more advances. Its outstanding use today is as the oxide, and because of its extreme whiteness, high refractive index, chemical stability, and relative cheapness, it has become the white pigment used in the largest volume. New developments in the uses of titanium metal, potential and actual, may surpass the pigment use of the oxide before many years. TITANIUM-BEARING MINERALS Although a number of minerals contain titanium as the principal metal, only a few are of commercial importance. These are arizonite, ilmenite, and rutile. The other oxides, brookite, pseudobrookite, and anatase, occur in a few deposits, one at least of minor importance. The silicate titanite, and the double oxide of calcium and titanium, perovskite, occur in a few deposits in quantities sufficient to be considered as potential ores were not richer deposits of the oxides available elsewhere. Arizonite is a name given by Palmer46a to a mineral found some years ago in minute quantities in Arizona, which has the formula Fe203.3Ti02. Unexpectedly, it was found that the black titaniferous iron oxide found in large quantities on the beaches of many continental land masses corresponds in chemical composition to this formula (although ferrous oxide is always present). No one has yet been able to prove that the commercial mineral on the beaches is truly arizonite, or an allotropic modification of it, since X-ray investigations by Howard Carl and A. F. Gabriel, of the U. S. Bureau of Mines, and by the X-ray laboratory of the Chemical Department at the Experimental Station of the du Pont company, have shown only that the sand mineral gives just a jumble of lines, rather than an identifiable pattern. Lack of a better name,

Jan 1, 1949

By H. I. Smith

WHEN Spain established colonies on the North American continent, some of her land grants, in what is now the United States, reserved to the Crown deposits of gold, silver, and mercury. Later mineral rights were reserved under some of the English Crown charters involving land in the eastern part of North America, with provisions for the payment of royalties thereon to the Crown. Reservation of mineral deposits to the United States Government was instituted by an ordinance of Congress on May 20, 1785, which applied to such deposits in the Northwest Territory, then north of the Ohio River and east of the Mississippi River, and provided that there should be reserved "one third of all gold, silver, lead, and copper mines, to be sold or otherwise disposed of as Congress shall hereafter direct." Little was known then of the mineral resources of the country; the Great Lakes copper region had just come into the possession of the United States by treaty and much of the western mineral land still belonged to France and Spain. The policy of leasing mineral deposits was enacted by Congress under the act of March 3, 1807, which provided that "the President of the United States shall be, and is hereby, authorized to lease any lead mine which has been or may hereafter be discovered in the Indiana Territory, for a term not exceeding five years," and in the same year the Government reserved 345,600 acres of land in northern Illinois, valuable for lead. In 1816 Congress provided that in all cases where a tract of public land containing a lead mine or salt spring was applied for by settlers on the public domain, no permission to work the mine or spring would be granted without the approbation of the President of the United States. By the act of March 1, 1847 (9 Stat. 146), the control of mineral lands was transferred, with all records, from the War Department to the Treasury Department, and by the act of March 3, 1849 (9 Stat. 395), supervisory powers over lead and other mines of the United States were transferred to the Secretary of the Interior. Following the discovery of gold in California in 1848, President Polk advocated the leasing of mineral lands acquired from Mexico under the treaty of 1848. However, owing to the lack of communication and transportation facilities and the consequent difficulty of checking on production and operations, leasing was found impracticable. Mining was permitted to be carried on in each district under rules made by the miners themselves and patterned after the Mexican mining system. To meet the situation, Congress enacted mining laws in 1866, 1870, and 1872, which provided for possession by location and for private ownership, after discovery, by patent of essentially all mineral deposits belonging to the United States, except coal. Many other acts were passed by Congress applying to specific regions and states, reserving salt, lead, or other minerals, some of which provided for the leasing of such deposits. However, very few if any leases were issued thereunder. Not until 1901 (31 Stat. 745) were the mining laws extended to include salt, and in 1910 they were revised to specify salines and associated products. At the turn of the century, it became more and more evident that the mining laws developed for metallic minerals were not practical for the development and conservation of oil and gas, coal, potash, phosphate, or oil shale. Following withdrawals by the Secretary of the Interior as authorized by the act of June 25, 1910, the Department of the Interior recommended leasing legislation; however, it was not until February 25, 1920, that the Mineral Leasing Act was passed by Congress. This act authorized leasing all public lands potentially valuable for oil, gas, coal, phosphate, sodium, or oil shale. The Organic Act, creating the Geological Survey in 1879, imposed upon its director the duty of classifying the public lands.' The early years of the Survey were devoted largely to the accumulation of fundamental data and, with only minor exceptions, land classification was not seriously undertaken until 1906. Since that year, it has been actively pursued with respect particularly to leasable minerals and water power values. On March 3, 1873 (17 Stat. 607) Congress authorized the sale of coal lands of limited acreage to individuals at $10 to $20 an acre, depending on the distance from a railroad, and in 1907 a new scale of prices was adopted by the Secretary of the Interior, based, more logically, on the quality and thickness of the coal deposits, their depth below the earth's surface, and their accessibility. At that time it was much cheaper and easier to obtain incidental title to coal rights under the homestead laws at $1.25 an acre. On March 3, 1909, the first separation act (35 Stat. 844) became a law. It authorized patents, with a reservation of the coal and mining rights involved to the United States, to persons who in good faith had entered public lands under the non-mineral land laws prior to withdrawal, classification, claim, or report that such lands were valuable for coal. It solved the problem only partially, and the practice thereupon adopted by the department of making coal withdrawals "from all forms of entry" instead of "from coal entry" expedited the more complete solution effected by later acts. By the act of June 22, 1910 (36.Stat. 583) withdrawn and classified coal lands were declared subject to entry under the homestead, desert land, and Carey acts, provided a waiver of the coal rights accompanied the application, and by the act of April 30, 1912 (37 Stat. 105) the same privilege was extended to State selections and isolated tracts. The act of August 24, 1912 (37 Stat. 496) extended the separation policy to lands withdrawn for oil and gas in Utah, and finally the act of July 17, 1914 (38 Stat. 509) extended it to all nonmineral filings on public lands theretofore or thereafter

Jan 1, 1955

By Harold R. Wampler, John L. Bolles, Adrian J. Broderick

Phelps Dodge's 60,000 tpd Morenci Concentrator has been in operation since 1942. The integrating of process control applications into the concentrator began in 1972. A process control system is presently on-line controlling 30 primary grinding circuits and all reagent additions. The system consists of a centralized control room process control Computer, on-stream X-ray analyzer, on-stream particle size analyzers and an operator interface. This paper describes the process control system's development, control concepts and its influence on the concentrator performance.

Jan 1, 1978

By Charles N. Bell

The Telluride mining district of southwestern Colorado is defined by the 37" 45' and 38" parallels of latitude and 107" 45' and 108" meridians of longitude. Telluride was never a boom camp, but has had a steady growth. In recent years, notwithstanding the business depression of 1920, the business has been the same as in normal years. The first prospector is said to have appeared in 1875, in which year locations on the Smuggler vein were made. Shipments were made in 1877 and 1878, and in 1879 milling the ores was attempted. While the district produced high-grade ores, it did not become important until 1890, when the Rio Grande Southern R. R. was completed from Ridgway to Telluride. The railroad has since been extended to Durango. In the fall of 1896, 400 stamps were in operation, and the annual production was $3,000,000.00, two-thirds of which was gold. The total production from 1875 to 1923 was: gold $58,274,527; silver 41,-830,920 oz., valued at $31,016,893; copper 15,258,866 lb., valued at $2,533,291; lead 166,056,484 Ib., valued at $8,324,910; zinc 18,141,182 Ib. valued at $1,323,787; or a total production of $101,473,408. All claims are held in fee. Most of them are 1500 by 300 ft. but claims located within the last few years are 1500 by 600 ft. General supplies are obtained at Telluride, Denver, and Salt Lake. The largest mines are within 6 miles of the town of Telluride. Denver is 422 miles and Salt Lake is 439 miles, by rail, from Telluride. One-half of the distance to Denver and one-sixth of the distance from Telluride to Salt Lake is by narrow-gage railroad. The labor is efficient. The best miners are Italians and Austrians, then Slavs, Greeks, and Mexicans follow in the order mentioned. There are no labor unions. There are no serious mine pumping problems, the drainage being through adits. The Tomboy and Smuggler companies pump water from their reservoirs, the former for milling and domestic purposes and the latter for milling, power, and domestic purposes. BIBLIOGRAPHY A partial bibliography of the Telluride District is: Geologic Atlas Telluride No. 57; Preliminary Report on the Mining Industries of the

Jan 1, 1925

By H. A. Koch, R. L. Slobod

This paper discusses a new oil recovery process called the "miscible slug process." This process involves the injection of propane or LPG into the reservoir prior to gas injection. The operating conditions are maintained so that the slug is miscible with both the reservoir oil and the injected gas phase. Thus, a miscible phase displacement is achieved, and high recoveries are obtained from the area of the reservoir contacted. The most striking discovery of the laboratory study which included displacements from cores up to 123 ft in length was that relatively small slugs of LPG are effective over reservoir distances in the miscible displacement of oil. This makes possible the commercial application of the process. The important factors controlling the size of the slug are: (I) reservoir length, (2) reservoir fluid composition, and (3) reservoir pressure at the displacement front. Of lesser importance are the effects of injection rate and porous medium type. Questions which have not been completely answered deal with the effects of gravity and reservoir inhomogeneities on the process. INTRODUCTION One of the major problems facing the oil industry today is recovery of the large fraction of the discovered oil which will remain unrecovered unless some new processes are found. Water flooding has been one successful method used to increase recovery over natural depletion. But even successful water floods may leave 25 to 40 per cent of the pore space filled with residual oil. Recently a process which involves the use of thermal energy has been reported1,'*' which may prove useful in increasing recovery from shallow reservoirs containing highly viscous crudes. This paper deals with a new oil recovery process involving use of miscible phases to displace the oil from the reservoir. Miscible phase displacement oil has been an intriguing idea because the elimination of capillary effects in the reservoir leads to 100 per cent recovery in the areas contacted by the miscible displacing phase. The big deterrent in the past to the practice of miscible phase displacement has been the high cost involved in using large volumes of solvent in the process. The use of high pressure gas to achieve a miscible phase displacement of reservoir oil has been reported4,5 as one economically feasible method. However, this process calls for the maintenance of pressures above 3,000 psi at the dis-placement front. The process described in this paper is not restricted to high reservoir pressures; the only qualification being that the slug of material which is injected into the reservoir must be miscible with both the displaced oil 2nd the displacing phase. Two such cases are the use of an alcohol slug followed by water to achieve a mis-cable water flood, and the use of a low boiling hydrocarbon slug such as propane followed by gas to achieve a miscible gas drive. This paper will deal specifically with the propane dug process. This process will obtain a miscible phase displacement at pressures as low as about 1,200 psi at a reservoir temperature 01 150°F. The process is very simple. The propane displaces oil completely at one front because it is miscible with the oil, and gas displaces the propane completely at a second or trailing front because it is miscible with the propane. A small band of propane should thus remain wedged between the gas and oil phases. This idea has been called the "miscible slug process."6 Unfortunately, the propane slug will become diluted as it flows through the reservoir. This results from a mixing action since the fluids flow through a complex reservoir porous medium rather than simple capillaries. Fig. 1 diagrams a miscible slug displacement. The effects of some of

Jan 1, 1958

By John D. Sullivan, Edwin J. Rogers, Chester R. Austin

THE problem of making a building unit combining the necessary physical and mechanical properties and good thermal insulation has been foremost in the minds of architects and ceramic and construction engineers for many years. This paper presents the results of studies on thermally expanding shales or clays to produce light-weight cellular products suitable for making building units. An expanded clay block suitable for building purposes should be large enough so that substantial savings may be effected in labor costs in laying the wall. The permeability should be low and it should have sufficiently good "dry-wall" characteristics to permit exposing the exterior surface to the elements, and to permit plastering directly the inside wall surface. The thermal conductivity should be low and the mechanical properties should be adequate. Obviously, a unit possessing satisfactory qualities for constructing an outside wall would be satisfactory for interior walls and for back-up purposes. The results of studies on bloating various shales or clays† and the properties of the expanded products are reported. In another paper1 basic factors involved in bloating of clays are discussed. Manufacturers of ceramic products, particularly structural clay, may encounter bloating of the ware during burning, and precautions must be followed to avoid this phenomenon. About 1927 the C. F. Burgess Laboratories, Madison, Wis., while carrying on an investigation for the American Face Brick Research Corporation, conceived the idea of intentionally bloating clay while holding it in a restrained condition, with the hope of producing a unitary cellular mass. Work was carried on until about 1931, when studies were terminated because of business conditions. These studies were continued later by The Western Brick Co., Danville, Ill., which developed a process of "inwardly expansive bloating." The major purpose of the latter investigation was to produce back-up tile to compete with concrete blocks made from Haydite or cinder aggregate. Haydite is a light-weight aggregate formed by heating certain clays or shales rapidly in a rotary kiln. While the investigations at the C. F. Burgess Laboratories or at Western Brick Co. were not carried far enough to lead to the commercial production of material for the construction of walls, particularly outside walls, they showed that certain clays could be thermally expanded and that it was possible to produce a material of low permeability with a large percentage of the total voids or cells closed. Commencing in 1939, the Ozark Chemical Co. sponsored a research program at Battelle Memorial Institute for the purpose of determining whether it is technically feasible to make thermally expanded building units, and specifically to get answers to the following questions:

Jan 1, 1942

By A. R. Troiano, E. A. Steigerwald, F. W. Schaller

The kinetics of crack propagation in a hydrogenated high-strength steel at subzero temperatures indicated that cracking progressed in a discontinuous fashion. The delayed failure process thus involves a series of crack initiations rather than the continuous growth of a single crack. The incubation time required for the initiation of delayed failure was controlled by the diffusion of hydrogen. The activation energy for the process was 9120 cal per g-alom. As the test temperature was lowered the incubation time constituted a greater percentage of the total tinze to fracture, and al -50°F the incubation and fracture times were essentially coincident resulting in instantaneous, catastroplzic fracture. A unique feature of hydrogen embrittlement is the delayed failure process in which the material fails under the action of a sustained load even though it is capable of supporting a higher load for a finite period of time.')' Delayed failure of steel and titanium is characterized by an incubation time, preceding the initiation of a crack in a highly localized region, and the subsequent growth of the crack to ultimate failure.3-5 The kinetics of crack growth in hydro-genated high-strength steels have been studied through the use of resistance measurements and have an important bearing on the mechanism of delayed failure. Delayed failure is believed to be merely a facet of hydrogen embrittlement in which sufficient time is allowed during a test for hydrogen diffusion. The current theories employed to explain hydrogen em-brittlement can be grouped into two types. one6-8 explains the embrittlement on the basis of the pressure exerted by molecular hdrogen in lattice voids or defects while the other9-10 attributes the embrittlement to the influence of hydrogen in the lattice. The mechanism used to explain the nature of the crack kinetics in delayed failure is based on the stress-induced diffusion of hydrogen to the area of maximum triaxiality.3 When the hydrogen concentration in this region reaches a critical value, a crack is nucleated. This initial crack propagates instantaneously until stopped by the higher fracture stress of the adjacent material of lower hydrogen content. The continuation of cracking must then await the further diffusion of hydrogen to the new region of triaxiality near the base of the crack where another initiation will occur. From this mechanism it follows that crack propagation is nothing more or less than a series of initiations with limited fracture. The purpose of this investigation was to examine the kinetics of crack growth in an effort to determine whether or not the process was discontinuous. Studies of crack propagation were conducted at low temperatures to retard the diffusion of hydrogen which is presumed to be the rate controlling process in delayed failure. MATERIALS AND PROCEDURE Specimen Preparation—A commercial heat of air-craft quality SAE-AISI 4340 steel, designated as Heat G, was furnished by the Republic Steel Co. in the form of %-in. hot-rolled bars. The material had the following chemical analysis: Composition of 4340 Steel—G Heat C Mn Si Ni Cr Mo 0,395pct 0.82pct 0.29pct 1.76pct 0.85pct 0.25pct Notched tensile specimens with less than a 0.001 in. radius, Fig. 1, were used throughout the investigation. The specimens were heat treated to a 230,000 psi strength level according to the following sequence: a) Normalize bar stock at 1650°F for 1 hr, b) Stress relieve at 1200°F for 4 hr and furnace cool,

Jan 1, 1960

By W. A. Ver Wiebe

Under the impetus of new demands caused by the war, the oil and gas industries of Kansas established new records during the year 1942. In all, 1513 test wells were drilled, which is somewhat of a drop from the figure of 2113 for 1941. The 1513 tests yielded 800 new oil wells, 85 new gas wells, and 628 dry holes. Thus there was an increase in two categories, the gas wells and the dry holes. Considering that last year only 592 dry holes were completed out of a much larger total, the figure of 628 dry holes causes some concern among local operators. The increase in unsuccessful tests illustrates once more the fact that each year it is becoming harder to find the remaining oil pools. When the figures are broken down, it appears that western Kansas accounted for 1177 tests, of which 689 were oil wells, 33 gas wells, and 455 dry holes. The total potential daily initial production uncovered by the successful wells amounted to 753,178 bbl. of oil and 619,734,000 cu. it. of gas. The figures for new initial production indicate a substantial drop from last year's figure of 1,691,000 bbl., and the figures on gas are slightly higher. In 1941 the new gas as based on a daily potential was 508,000,-000 cu. ft. In eastern Kansas, 336 wells were drilled. Among these in were oil wells, accounting for a daily initial potential production of 16,199 bbl. The new gas wells numbered 52 and added 253,725,000 cu. ft. per day to the gas potential production of the state. The remaining tests, 173 in number, were dry. It is interesting and perhaps significant that about half (630) of the wells drilled in western Kansas were drilled by the independent operators. Among the large companies, the Cities Service Oil Co. drilled 163 wells; the Stanolind Oil and Gas Co., 52; the Skelly Oil Co., 39; the Continental Oil Co., 48; and the Shell Petroleum Co., 21 wells. In eastern Kansas the independent operators drilled 297 out of the total of 336 wells. Among the major oil companies the Cities Service Oil Co. drilled 19; the Phillips Petroleum Co. 7; and the Sinclair-Prairie Oil Co., 6 wells. The figures based on relative percentages of dry holes to successful oil or gas wells are revealing. In western Kansas almost one half of all wells drilled by the independent operators were dry holes. The major oil companies drilled approximately 547 wells in western Kansas, of which 379 were successful in finding either oil or gas. It thus appears that the major companies fared better than the independents. In eastern Kansas the major companies drilled 39 wells, of which 29 were successful in finding commercial quantities of oil or of gas. No less than 329 wildcat test holes were put down in western Kansas and 105 in eastern Kansas, or 434 in all, during 1942. Considerably more than half of these were drilled by independent operators; 223 in western and 99 in eastern Kansas. An exploratory hole 56 mile or more from production is regarded as a wildcat well in Kansas. On a percentage basis, about 80 per cent of wildcat wells were failures. In western Kansas only 20 per cent found either oil or gas. The failures were about equally distributed among the major

Jan 1, 1943

By W. A. Ver Wiebe

Under the impetus of new demands caused by the war, the oil and gas industries of Kansas established new records during the year 1942. In all, 1513 test wells were drilled, which is somewhat of a drop from the figure of 2113 for 1941. The 1513 tests yielded 800 new oil wells, 85 new gas wells, and 628 dry holes. Thus there was an increase in two categories, the gas wells and the dry holes. Considering that last year only 592 dry holes were completed out of a much larger total, the figure of 628 dry holes causes some concern among local operators. The increase in unsuccessful tests illustrates once more the fact that each year it is becoming harder to find the remaining oil pools. When the figures are broken down, it appears that western Kansas accounted for 1177 tests, of which 689 were oil wells, 33 gas wells, and 455 dry holes. The total potential daily initial production uncovered by the successful wells amounted to 753,178 bbl. of oil and 619,734,000 cu. it. of gas. The figures for new initial production indicate a substantial drop from last year's figure of 1,691,000 bbl., and the figures on gas are slightly higher. In 1941 the new gas as based on a daily potential was 508,000,-000 cu. ft. In eastern Kansas, 336 wells were drilled. Among these in were oil wells, accounting for a daily initial potential production of 16,199 bbl. The new gas wells numbered 52 and added 253,725,000 cu. ft. per day to the gas potential production of the state. The remaining tests, 173 in number, were dry. It is interesting and perhaps significant that about half (630) of the wells drilled in western Kansas were drilled by the independent operators. Among the large companies, the Cities Service Oil Co. drilled 163 wells; the Stanolind Oil and Gas Co., 52; the Skelly Oil Co., 39; the Continental Oil Co., 48; and the Shell Petroleum Co., 21 wells. In eastern Kansas the independent operators drilled 297 out of the total of 336 wells. Among the major oil companies the Cities Service Oil Co. drilled 19; the Phillips Petroleum Co. 7; and the Sinclair-Prairie Oil Co., 6 wells. The figures based on relative percentages of dry holes to successful oil or gas wells are revealing. In western Kansas almost one half of all wells drilled by the independent operators were dry holes. The major oil companies drilled approximately 547 wells in western Kansas, of which 379 were successful in finding either oil or gas. It thus appears that the major companies fared better than the independents. In eastern Kansas the major companies drilled 39 wells, of which 29 were successful in finding commercial quantities of oil or of gas. No less than 329 wildcat test holes were put down in western Kansas and 105 in eastern Kansas, or 434 in all, during 1942. Considerably more than half of these were drilled by independent operators; 223 in western and 99 in eastern Kansas. An exploratory hole 56 mile or more from production is regarded as a wildcat well in Kansas. On a percentage basis, about 80 per cent of wildcat wells were failures. In western Kansas only 20 per cent found either oil or gas. The failures were about equally distributed among the major

Jan 1, 1943

By J. H. Bucher

The effect oj strengthening by the precipitation of CbC on the toughness offerrilic steel (0.11 pct C, 0.74 pct Mn, 0.02 pct Cb) was stlrdierl. A g-veater degree of pvecij~itatiotz strengthning is ohtaznable by aging the so11ution-treated steel rtt velaticely Low temperature was (1050" to 1l0O3F) than at higher temperatures (I150" to 1200°F). Tlzis ),eslrlts because a finer dispersion of CbC is obtained. However, the ductile-brittle transition te~ripertltlo.e is raised approximately tlzjeee tirues as IFLIIC~ perv a given yield stress increase) by aging in the lower tempareture range, as opposer1 to the Irigher temperaturee range. This is proposed to result pl-iir~avily because different precipitation distributions ar-e associated with the different aging -treaments. For tile steel aged at 1050" and 1100 F, heavy: precipitation on disloccctions occurs resulting in a high degree of rlislocution pinningh tl~us lowevirzg- the toilguiess. in tll c(.rise of the steel aged at 1150 'a?zd 1300"F, Pvecipitatiol~ is irzove g-enerally distributed throughout the matrix rather limn preferentially on dislocations.; and Ike detlsitj, oj mobile dislocations is not sttyong-ly affected. THE most effective means of strengthening hot-rolled ferritic steels are grain refinement and precipitation hardening. It is well-known that grain refinement increases both the strength and the toughness. However, the upper limit of yield strength obtainable by grain refinement alone is about 60,000 psi,'12 i.e., without the formation of acicular structures of lower toughness. The most economical means of obtaining higher strengths is the addition of small amounts of elements such as columbium, vanadium, and titanium which form carbonitrides. These precipitates are very effective in increasing the strength, but the ductile-brittle transition temperature is is Although it is agreed upon that precipitation decreases the toughness, there has been little effort to isolate the causative aspects of embrittlement. The purposes of this research are to assess quantitatively the embrittlement associated with different precipitate distributions and morphologies, and to correlate the degree of the embrittlement with the microstruc-ture. In this manner, a more fundamental insight into the mechanism of embrittlement may be gained. The steel selected for this purpose was a low-carbon, columbium-bearing steel which, after solution treatment, was aged in various time-temperature cycles while attempting to hold all other microstructural variables constant. MATERIALS AND PROCEDURE The composition of the steel used in this investigation is given in Table I. Starting with commercially hot-rolled material 0.074 and 0.280 in. thick, tensile blanks were cut from the thinner material and sub-size Charpy blanks from the thicker stock. The steel had been rolled using a low finishing temperature and rapid cooling after hot rolling to produce grain refinement. Also, chemical-extraction analysis and electron-microscopic examination revealed that the cooling was rapid enough to suppress any significant precipitation of CbC. Therefore, the as-rolled steel is essentially in the solution-treated condition in terms of the precipitation reaction, and it was used as the base material in this investigation. The room-temperature tensile properties of the as-rolled steel aged at 1100", 1150", and 1200°F for various time intervals were determined, see Table 11. The ductile-brittle transition behavior was studied for smooth and notched tensile specimens, and longitudinal half-size (0.200 in. thick) Charpy V notch specimens aged at 1100" and 1150°F for various times, also Table 11. In addition, tensile specimens aged for single times at 1050" and 1200°F were evaluated with respect to their ductile-brittle transition. Only one 1050°F treatment was used because of the extremely slow kinetics of precipitation at this temperature and because no significant difference between 1100°F aging was observed. Only one treatment at 1200°F was used because aging at this temperature alters the shape of the grain boundary cementite particles present in this steel and complicates analysis. The design of the tensile specimens is given in Fig.1.

Jan 1, 1968

By R. S. Dean

THE first attempt to establish an equilibrium diagram of the lead-antimony series was made by Roland-Gosselin1 in 1896. This investigation classified the system as a purely eutectiferous one, with the eutectic at 12.5 per cent. antimony and 228° C. In the next year, Stead2 placed the eutectic temperature at 247° C. The error in temperature made by Roland-Gosselin, however, has been perpetuated in the literature with a remarkable degree of persistency; this value was accepted by Campbell (1902), and Ewen (1910),3 and will be found in the last edition of Desch's3 Metallography (1922). Gonterman's investigation, made in 1907, was the most complete one available at the time the present investigation was started. He concluded' that the system was a simple eutectiferous one and placed the eutectic at 13 per cent. antimony and 247°C. Other investigations by Tammann (1907),5 Garbow (1909),6 Rudolfi (1910),7 Loebe (1911),8 and Leroux (1913)9 added little, if any-thing, to Gonterman's diagram. A number of investigations have been made of physical properties of the alloys. The electrical conductivity of the series was studied by Matthiessen (1860)10 and by A. W. Smith (1921);" the thermoforce by Rudolfi (1910),12 and Pelabon (1923);13 the specific heat by Durrer

Jan 2, 1926

By Raymond Mancha

WHEN calculating the pressure-volume characteristics of projected mine-ventilat-ing circuits by orthodox methods, certain basic assumptions are required in order to employ the various available empirical data. It is assumed, for example, that the mine air is an incompressible fluid subjected to isothermal flow, an assumption suffi-ciently accurate for practical purposes since pressure and temperature differentials are small throughout the average circuit. A more erroneous assumption, however, is that all air is accounted for as it travels throughout the mine. No attempt is usually made to evaluate stopping leakage as it occurs; instead, the air volume required at the last crosscuts is assumed to enter the mine, travel the vari-ous intake air courses intact, sweep the workings and travel out by the return air courses to the point or points of exit from the mine. Actually, there is a leakage of air from intake to return at every stopping, the quantity of this leakage depending upon the tightness of the stopping and the pres-sure difference across the stopping. Unfortunately, a lack of empirical data and knowledge of the condition of individ-ual stoppings makes an exact analysis of underground stopping leakage impossible. Generally, leakage is most severe through the old stoppings outbye the circuit. These are also subjected to higher pressure differ-ences than the newer inbye stoppings. Therefore the circuit air volume diminishes at a decreasing rate progressing from out-bye to inbye the circuit.

Jan 1, 1940

By Edgar S. Cook

Portions of this paper repeat in substance the statements made by me in an address before the meeting of the American Society for Testing Materials, held in June, 1903, at Delaware Water Gap, Pa. The views I then expressed, I still hold and believe to be pertinent to the present discussion of this subject. In doing my part, therefore, at the request of our Secretary, towards the further consideration by the Institute of the Physics of Cast-lron from a commercial as well as a theoretical standpoint,—a theme which received interesting treatment in our meeting some years ago, but has been somewhat neglected recently,—I make no apology for reiterating the views I have expressed elsewhere. Indications all point to the substitution of classifying pig-iron by chemical analysis for the old-time method of grading by fracture. Commencing with the larger users, and the makers of specialties, who require more positive information as to the composition than is afforded by the fracture; the use of pig-iron, guided by analysis, has spread with much greater rapidity to all classes of foundry-work than the most sanguine expected. Grading by fracture, as guided by experience with any particular brand of iron, has some points in its favor. The fact that, for so many years, castings of multitudinous forms, and for an endless variety of uses, were made in a fairly satisfactory

Jan 1, 1905

By Charles M. Behre

Under the caption "fault," geologists intend to include all mass movements of solid rocks over adjacent rock masses. When these are studied long after their origin, however, circumstances make it possible to recognize as "fault" only formations showing clear evidence of actual movement of one side with respect to the other. Necessarily the chief evidence consists of the offset of a vein, bed, or other key structure. Planes of movement parallel to the bedding, or nearly so, are recognized with difficulty or are overlooked and hence many important faults are wholly unrecorded. Indeed, among standard American references on structural geology, one alone emphasizes the importance of bedding-plane movements and that one only briefly1. For some time the writer, cognizant of this difficulty, has paid special attention to such movements, both as observed in the field and as recorded in the literature. It is believed that enough data are now at hand to justify a short discussion. Its purposes are fivefold. It is desired first to briefly classify and describe at least the more common kinds of bedding-plane faults, and second, to examine the causes and manner of their formation, at least in instances where the subject has not yet been well covered by other investigators. Third, certain by-products of bedding-plane movements are of such conspicuous importance to the economic geologist and mining engineer as to merit mention. Fourth, concrete illustrations should be placed before the reader in order to lend reality and to furnish a basis of comparison with his experience; such illustrations will necessarily be scattered through the text of this paper. They are only in part from the writer's own field observations. The fifth and prime objective of this paper is to direct attention to the great importance of movements on the bedding planes, in the hope that the recognition of such movements and their significance may simplify mining problems.

Jan 1, 1937

By S. Fróes Abreu

The importation of liquid fuels in Brazil amounts to about 1,300,000 tons; 30 per cent of this total being gasoline for automobiles and airplanes. Statistics show an increasing consumption of gasoline notwithstanding the use, daily greater, of fuel alcohol, a domestic fuel of low cost in the producing areas. The Brazilian market for petroleum products has shown a tendency to grow as the country has steadily developed— expansion of the industries in the areas already developed, and also the recent occupation and population of new zones. The war has brought many difficulties to Brazil. It has limited the importation of petroleum products, which came mostly from the United States, Venezuela and Mexico. During the first days of the present crisis automobile and truck traffic was vastly curtailed; but the national activity in the production of more fuel alcohol, and principally in the development of producer gas, has done much to provide a solution for the transportation crisis threatened at the beginning of the gasoline shortage. Many thousands of cars and trucks in Brazil are now burning producer gas made from charcoal. Producer gas for automobiles has been improved by Brazilian engineers and many new types have appeared. - Production There is only one producing oil field in Brazil—the one in the State of Baia, near the Baia de Todos os Santos. The first producing oil well was drilled in Lobato in 1939 by the Federal Government following studies carried on in that area by Oscar Cordeiro, S. Froes Abreu, G. Paiva and J. Amarai. The field and laboratory work done by these men was published in 1936 in a paper entitled " ContribuicBes para a Geologiado Petroleo no Reconcavo (Baia)," which indicated the potentialities of the area as an oil producer. After the discovery of the first producing well, the Brazilian Government issued a decree establishing an area, 60 km. in radius, as a National Reservation. This first well was drilled in Lobato. In no other locality in Brazil is any petroleum produced. Although many wells have been drilled in the southern part of Brazil, on the northeastern coast and in the Amazon Basin, they yield nothing. Actual production is below 1000 bbl. daily. The producing area covers Itaparica Island, Candeias and Arath, Joanes Island and Lobato. Since very little geological information was available, especially about subsurface structure, it was necessary to drill several wildcats in order to collect the data essential in the choosing of good locations. The United Geophysical Co. was contracted to perform a geophysical survey to clear up the major problems concerning the oil deposits in the Reconcavo beds. The best wells in Reconcavo are on Itaparica Island, where the daily flow amounts to about zoo bbl.; in other sectors production is considerably lower and most of the wells are pumping. In the Aratfi sector, near an area of very light oil, there is an important gas field, with wells producing about I0,000,000 cu. ft. daily.

Jan 1, 1944

By S. Fróes Abreu

The importation of liquid fuels in Brazil amounts to about 1,300,000 tons; 30 per cent of this total being gasoline for automobiles and airplanes. Statistics show an increasing consumption of gasoline notwithstanding the use, daily greater, of fuel alcohol, a domestic fuel of low cost in the producing areas. The Brazilian market for petroleum products has shown a tendency to grow as the country has steadily developed— expansion of the industries in the areas already developed, and also the recent occupation and population of new zones. The war has brought many difficulties to Brazil. It has limited the importation of petroleum products, which came mostly from the United States, Venezuela and Mexico. During the first days of the present crisis automobile and truck traffic was vastly curtailed; but the national activity in the production of more fuel alcohol, and principally in the development of producer gas, has done much to provide a solution for the transportation crisis threatened at the beginning of the gasoline shortage. Many thousands of cars and trucks in Brazil are now burning producer gas made from charcoal. Producer gas for automobiles has been improved by Brazilian engineers and many new types have appeared. - Production There is only one producing oil field in Brazil—the one in the State of Baia, near the Baia de Todos os Santos. The first producing oil well was drilled in Lobato in 1939 by the Federal Government following studies carried on in that area by Oscar Cordeiro, S. Froes Abreu, G. Paiva and J. Amarai. The field and laboratory work done by these men was published in 1936 in a paper entitled " ContribuicBes para a Geologiado Petroleo no Reconcavo (Baia)," which indicated the potentialities of the area as an oil producer. After the discovery of the first producing well, the Brazilian Government issued a decree establishing an area, 60 km. in radius, as a National Reservation. This first well was drilled in Lobato. In no other locality in Brazil is any petroleum produced. Although many wells have been drilled in the southern part of Brazil, on the northeastern coast and in the Amazon Basin, they yield nothing. Actual production is below 1000 bbl. daily. The producing area covers Itaparica Island, Candeias and Arath, Joanes Island and Lobato. Since very little geological information was available, especially about subsurface structure, it was necessary to drill several wildcats in order to collect the data essential in the choosing of good locations. The United Geophysical Co. was contracted to perform a geophysical survey to clear up the major problems concerning the oil deposits in the Reconcavo beds. The best wells in Reconcavo are on Itaparica Island, where the daily flow amounts to about zoo bbl.; in other sectors production is considerably lower and most of the wells are pumping. In the Aratfi sector, near an area of very light oil, there is an important gas field, with wells producing about I0,000,000 cu. ft. daily.

Jan 1, 1944