Search Documents

By L. H. Robinson

A proposed method of drilling utilizes sequential detonation of two types of explosive charges delivered to the hole by a conventional drilling fluid through pipe. A shaped charge first produces a long thin hole. A second charge, called a gauging charge, is pumped into the thin hole, explodes, and enlarges it to full gauge. In one suggested configuration, the explosives are contained in cylindrical capsules 4- to 5-ft long. A drilling head is positioned 2- to 3-ft off bottom. When a capsule is pumped to the bottom of the hole and stops, pressure inside the drill pipe increases and differential pressure detonates the explosive. Primacord along the length of the capsule disintegrates the capsule. The debris circulates out of the hole with the drilling fluid. The gauging-charge action was examined using 2-ft cubes of Berea sandstone. The sandstone (18 per cent porosity) was vacuum-saturated with water and surrounded by concrete. To prevent reflected tensile pulses, the acoustical impedance of the concrete matched that of the sandstone. A 750-psig pressure was applied to a drilling fluid within a shaped-charge-formed hole before detonating the gauging charge. In these tests, 190 gm of rock were removed for each gram of explosive detonated. A similar series of experiments on low-porosity (0.40 per cent) metamorphic limestone provided a more rigorous test. Extensive fracturing from the gauging-charge action prevented an estimate of the volume of the expanded hole. The diameter of the hole was irregular, ranging from about 2 to 4 in, or about fivefold larger than the hole created by the shaped charge. INTRODUCTION In the past, explosives have found a varied but somewhat limited use in the oil field. An early well stimulation technique, still in use today, in vo lves shooting ni troglycerin to en large the borehole and to increase matrix permeability near the wellbore. Bullets and jets are now the conventional method of perforating casing and tubing. Detonations are frequently used to "back off" or "shoot off" stuck pipe and, of course, seismo-graphic work has long depended on explosive-generated pulses to find attractive earth structures. Efforts to use explosives in drilling operations have received limited examinations1-3 which, in one respect, is surprising because explosives offer one way to transmit large amounts of energy directly to the bottom of the hole. Recently, Ostrovskii l described a Russian method of drilling with explosives that utilizes small capsules containing explosives which are pumped into the mud stream to the bottom of a borehole. As the capsules leave the end of the drill pipe, a detonation mechanism is armed. Impact detonates the explosive. In another configuration, two liquids (an oxidizing agent and fuel) in the capsule are separated by a frangible membrane. Separately, the liquids are nonexplosive. Near the bottom of the drill pipe, the capsule passes through a narrow constriction which ruptures the membrane. The mixing of the liquids produces an explosive. Impact is again used to detonate the explosive. About the time Ostrovskii was developing his method, Humble Oil & Refining Co. was independently doing research on another explosive drilling concept based on the sequential detonation of two types -of explosive charges. The proposed technique consisted of alternately pumping a shaped charge and then a "gauging charge" down a well. The shaped charge should drill a long, tapered hole, and the gauging charge should expand it to full gauge. This paper presents the visualized drilling concept and gives results of laboratory work which showed that sequential firing of charges can form hole at an attractive charge-to-rock removal ratio. An important finding was that increased environmental pressure, which is to be expected in wells, increases rock removal efficiency of the gauging charge.

Jan 1, 1966

By Michael A. Toole, O&apos

INTRODUCTION The tremendous capital investment required to produce a low grade ore deposit demands a reliable answer to the question: "How much does it cost to drill a well to produce the uranium that geologists have indicated is there in the ground?" However, you will find the answers given will be many and varied, depending on whether they come from the operating company, the drilling contractor, a geologist, a reservoir engineer, purchasing agent, or whoever. Each generally considers only a limited area of the total operation. The operating company usually depends upon the drilling contractors, service companies, and consultants to supply expertise. Because it is often difficult to see the "whole picture" or even to agree upon what the "whole picture" is, planning a well program and its costs is often done piecemeal. Frequently, costs "saved" in one area of the program are needlessly spent in another, because the effect of one area upon the other was overlooked. Since the drilling fluid is such an influential part of the drilling program, it should be given utmost consideration when planning the overall program. As W. D. Lacabanne wrote in 1954: "The drilling fluid system is understandably called the heart of the rotary oil drilling rig. Any other type of rotary rig.... should benefit by the incorporation of mud fluids in the drilling scheme." And G. R. Gray mentions that "The driller recognizes the drilling fluid as one of the useful tools available to solve drilling problems." However, in minerals drilling, only in recent years has the drilling fluid been considered as more than a tool to get through special problem areas. Although there are many similarities between drilling for oil and gas and drilling for minerals, the differences in the drilling equipment used justifies designing specific fluids for the minerals drilling industry. NL Baroid/NL Industries, Inc. has been a leader in introducing such fluids and in providing technical know-how to the minerals drilling industry. The purpose of this paper is: (1) to discuss the selection of drilling fluids to meet specific drilling conditions during both exploration and production and (2) to show the interrelationship among factors present in the exploration and production phases that influence total well costs. DRILLING FLUIDS FOR DRILLING PROBLEMS The drilling fluid is a tool that can be used to improve drilling performance by improving hole cutting, cleaning, stability, and formation productivity. Properly formulated and maintained drilling fluids enable the drilling operation to be carried out with increased efficiency and lower total (overall) costs. However, it should be noted that not all drilling problems can be solved by even the most carefully prepared and maintained drilling fluids. Of the many possible drilling problems encountered in a well before reaching target depth, this paper will discuss only those most likely to be present in the shallow [61 to 610 m (200 to 2000 ft)] drilling operations in South Texas. LOST CIRCULATION Loss of circulation is the most common problem encountered in drilling. Because the losses occur under varied conditions, it is often difficult to determine the exact causes. "Lost circulation" or "lost returns" means the partial or complete loss of drilling fluid to voids in the formation. "Loss of water" while drilling with water may take place into any permeable section and should be distinguished from "water loss" or filtration of fluid through the filter cake of mud solids laid down on a permeable formation. "Loss of water" can frequently be stopped by the addition of colloidal sized clay particles such as high yield bentonites, whereas "water loss" may be controlled with organic polymers. Subsurface conditions that lead to loss of circulation can be classified as: (1) natural fractures, (2) induced fractures, (3) unconsolidated or highly permeable formations (loose gravel), and (4) cavernous formations (crevices and channels). Loss of circulation may occur whenever the borehole pressure exceeds the formation pressure. The greater the differential pressure, the more likely it is that circulation may be lost. To stop loss of whole mud, voids must be bridged so that a filter cake can be laid down on the permeable section. The plugging material must be of the proper size and shape to offer greater resistance to the fluid flow around it than the flow up the annulus. A plugging composition that satisfies these requirements may not be able to be handled by the small rig pump available.

Jan 1, 1979

By K. E. Brown, F. W. Jessen

By utilizing an 8,000-ft experimental field well equipped with 10 gas-lift valves and 10 Maihak pressure recorders, gas-lift tests were conducted with port sizes ranging from 5/16 through I in. The well was equipped to provide accurate means of measuring surface pressures, temperatures, quantity of injection gas and fluid production. The tests were conducted in 2%-in. OD tubing, and the well was making 95 per cent water. A complete evaluation of gas-lift-valve port sizes shows the relationship of per cent recovery, gas-liquid ratios, minimum pressure created at the operating valve and horsepower requirements for each port. The length of time necessary for the fluid in the tubing to reach equilib.rium conditions after each cycle was recorded. Fallback of fluid at depths of 477, 969, 1,685, 2,493 and 4,290 ft was noted. For each port size, pressure loads of 2.50, 300, 350, 400 and 450 psi were lifted with a valve operating at approximately 550 psi at 6,000 ft. Gas-liquid ratios for each load were varied from excess gas to a gas volume per cycle whereby the load failed to reach the surface. Numerous curves are presented in evaluating the accumulated dara. The results show a 1-in. port to be the most efficient under all conditions. The production of intermittent liquid slugs against different-sized surface chokes was evaluated. These tests were conducted from a 7/16-in. ported valve at 4,072 ft. Tests indicate that, when possible, a %-in. in diameter choke or larger should be used at the surface. In the past few years most of the advancement in gas-lift operations has been made in continuous-flow operations. Yet, it is estimated that at least 70 per cent of the wells on gas lift in the United States are of the intermittent type. Since the term "slug flow" is sometimes used in both intermittent- and continuous-flow operations, it would be well to distinguish between the two types of flow. Continuous-flow gas lift is defined as a method whereby the fluids are produced at a continuous rate at the surface. This generally requires a continuous injection of gas through a surface choke; however, various other control devices sometimes are installed to eliminate freezing, to shut-off gas during natural flow periods, etc. The actual flow of fluids in the tubing may be of the slug type (one of many flow patterns known to exist in continuous flow). Intermittent flow is defined as a method of gas lift whereby the liquid is produced in separate piston-type slugs. Perhaps this type of flow could best be thought of as a ballistic-type flow where the liquid leaves bottom as a piston, propelled by a slug of expanding gas. Gas generally is injected through some type of control at the surface at predetermined intervals. However, the valve may have characteristics whereby gas can be injected through a small choke and still result in a ballistic-type flow. The purpose of the experimental work was to evaluate the most efficient port size to be used on the operating valve for the ballistic type of lift and, in addition, to establish the importance of utilizing a surface choke large enough to allow slugs to be produced without detrimental effects. This work is part of a compre- hensive study of both intermittent-and continuous-flow gas lift, representing a joint project conducted by the Ohio Oil Co., the Sun Oil Co., Otis Engineering Corp, and The U. of Texas. The problem of evaluating port sizes has been given little previous attention. Some work undoubtedly has been done which has not been published to date. Some tests were conducted when the wireline, mechanically-opened valve (Nixon) first came on the market. This valve was capable of utilizing full tubing area as its port size. It is known that this was a very efficient valve, but to the authors' knowledge the results of tests have never been published. EXPERIMENTAL EQUIPMENT These tests were conducted on an actual field well, the Ohio-Sun Unit Well No. 2-E, in the North Markham-North Bay City field, Matagorda County, Tex. The well incorporated 23/8-in. OD tubing and produced 95 per cent water. Since the running of equipment was to be quite elaborate and expensive, a well was selected in which both intermittent- and continuous-flow tests could be conducted. This particular well was capable of producing in excess of 1,000 B/D of liquid (95 per cent salt water), yet with a 3/64-in. in diameter bottom-hole choke, production was controlled to 82 B/D. Most of the intermittent tests were conducted at this low rate. Figs. 1 and 2 show all the surface and down-hole equipment. As can be seen, every attempt was made to insure that ample equipment was available for reliable testing procedures. Fig. 1 shows the surface testing equipment. The input gas was controlled first by a regulator, then

By W. W. Stephens, W. J. Kroll, H. P. Holmes

THE only two methods for producing commercial quantities of malleable zirconium, up to now, have been using magnesium reduction of the anhydrous chloride under a neutral gas, and using purification of raw zirconium by the iodide dissociation method on a hot filament. The purity of the metal obtained by the latter process is about the same as that resulting from the chloride reduction, with the exception of the oxygen content, which may be about 0.05 pct lower in the iodide metal. Even traces of oxygen have a strong hardening effect on zirconium. Since, in the iodide process, the impurities, Si, Al, Fe, Ni, and Mg in the raw zirconium used, are carried over, it would appear uneconomical to use this method of refining solely to eliminate the traces of oxygen, unless very soft metal is desired. One important step to improve the iodide method, namely, dissociating pure iodide made from carbide and recycling the iodine, which would change this refining process into a method for extracting zirconium from the ore, has not yet been made. The Bureau of Mines, by using the chloride reduction, wanted to produce quantities of a reasonably pure and malleable metal at low cost for large-scale industrial use. This aim has been achieved, and a pilot plant permitting production of 600 lb of malleable zirconium per week will be described (fig. 1). Briefly, the Bureau of Mines process consists of reducing purified gaseous anhydrous zirconium chloride with fused magnesium under a noble-gas atmosphere. The reaction product, magnesium chloride, and any excess magnesium metal present are removed from the sponge zirconium in the next step by fusion and evaporation in a good vacuum at about 925°C. In this process, care is taken to keep air out of contact with the hot metal, which otherwise would contaminate the product with oxygen and nitrogen. Both these impurities embrittle zirconium even when present in an amount as low as 0.1 pct. A number of previous reports1-3 describe the method and the various improvements that finally led to a workable process. The major steps made were the production of large quantities of carbide, which is the raw material for producing the chloride, its chlorination with reasonable efficiencies, and the elimination of iron trichloride contained in the raw chloride, as well as that of the zirconium oxide which is always present in this product. The physical nature of the anhydrous chloride, which sublimes at 331°C at atmospheric pressure and melts at 420°C under a pressure of 25 atm, made it necessary to provide a special safety device on the purification and reduction vessels in the form of a lead-alloy seal, permitting escape of excess gases if pressure tended to build up. The main difficulties encountered in the reduction and in the following step, salt separation in a vacuum at elevated temperature, were caused by the material from which the reaction pot was constructed—iron. This metal reacts with zirconium at about 940°C with formation of a eutectic. The last step, salt separation by evaporation of the magnesium and magnesium chloride in a vacuum, is quite unconventional and has not been used before on such a scale. It is only due to the improved construction of high-vacuum pumps, especially oil-diffusion pumps, that such a method could be used. The various steps of the Bureau of Mines process, as described in the general outline above, may be summarized as follows: (1) production of the carbide, (2) chlorination of the carbide, (3) purification of the raw chloride, (4) reduction of the pure chloride with fused magnesium, (5) separation of excess magnesium and magnesium chloride in vacuum at elevated temperature, and (6) melting of the sponge obtained. Production of Carbide The arc furnace, described in a previous report,' was improved both to reduce the graphite consumption caused by the burning of the bottom plates and to concentrate the heat in order to obtain better power efficiency. This was achieved by providing the bottom with graphite plates entirely embedded in refractory bricks, the contact with the current being made with three water-cooled copper plugs. Figs. 2 and 3 show the arrangement. The crucible, made

Jan 1, 1951

By John V. Beall

One Sunday night last month the phone rang and it was George Schenck from Penn State. How would we like to see a big scrap operation, he wanted to know. A few days later we were on the Connecticut turnpike headed for New Haven to visit a large scrap operation, M. Schiavone and Sons. George had a large clam basket in the back which he explained was for collecting trophies. The car shredder, he said, turns out some fancy metal shapes. In fact, they have gained a certain acceptance as objets d’art among George's friends and relatives. He thinks there may be a small, but possibly lucrative secondary market for shredded cars in the art world if the idea is imaginatively promoted. On the way to New Haven we received a briefing on the scrap industry. The scrap business grew from humble beginnings. Mostly it was started by a few immigrant Jews who collected junk in hand- or horse-drawn carts. The fortunate one might even have had a truck. Before proceeding further, we hasten to point out that the word "junk" is strictly taboo among scrap people, who prefer to refer to their industry as the "secondary metals industry."

Jan 1, 1970

By Frank E. Woolley, John F. Elliott

Mathematical models of the transient thermal behavior of a high-temperature solution calorimeter1-3 have been developed. The thermal behavior of the calorimeter is appoxirrzated by linear lumped-parameter models, and hence is described by sets of linear ordinary differential equations with constant coefficients The response of the models to various inputs is shown to agree with the response of the real system. Application of the modeling to experimental design and analysis of data illustrates the usefulness of simple models of complex systems. The early eperiments1,2 with the high-temperature solution calorimeter indicated that the change in the temperature of the bath resulting from the addition of a solute sample to the bath involved not only the direct effect due to the solution process but also possibly a secondary effect arising from the change in coupling between the bath and the induction heating coil. Consequently, an extensive analysis of the calorimeter was carried out, and models of the transient thermal processes of the instrument were developed to aid in improving the design and interpreting the behavior of the system. This paper describes the dynamic modeling; the use of it in treating experimental results has been reported earlier.3 The high-temperature solution calorimeter was constructed to measure directly the partial molar heats of solution of solute elements in a variety of liquid metal solvents.1-3 The calorimeter consists of an induction-heated liquid metal bath into which small samples of a solute element can be dropped. The bath temperature is recorded continuously, and the change in the measured bath temperature with time, dTm = f(t), resulting from the solute addition are the raw data from which the enthalpy change caused by the addition is determined. To extract the rmodynamic results from the data, the temperature change must be compared with that resulting from calibration additions of known enthalpy change. Accordingly, it is necessary to understand the transient thermal processes arising as a result of the addition to the bath. Neither modeling nor experimentation alone could provide the required insight into the working of the calorimeter. The alternate use of both methods in conjunction greatly assisted the design of the equipment and experiments, and the interpretation of the data. THE PHYSICAL CHARACTER OF THE SYSTEM The essential parts of the calorimeter, Fig. 1, for model studies are the thermocouple, the liquid metal bath and the surrounding refractories. The system is the solvent metal bath and those refractories around it which undergo a temperature change as a result of an addition to the bath, and which determine the way the temperature of the bath responds to an input. The inputs are the combined transient thermal effects arising when an addition is made to the bath. They include the thermal effects of the addition itself and the results of changed coupling between the bath and the induction coil. The response is the variation in the measured bath temperature, dTm(t) = Tm(t) - Tm(O), from an initial steady state resulting from the inputs. It was assumed in this study that the physical properties of the various elements of the system are independent of the inputs and time, although these properties may vary as the result of changes in the composition and size of the bath during a series of additions. This separation of inputs and the system is equivalent to assuming that the system is linear, i.e., that its behavior can be described by linear differential equations with constant coefficients. Linear behavior can be expected whenever the departure of each portion of the system from its steady-state condition is small enough to cause negligible changes in the thermal properties of the materials and in the various heat-transfer coefficients. Radiative heat transfer is important in this system, so the assumption of linearity should be valid only for small temperature deviations. Several conclusions were drawn from operation of the calorimeter in earlier experimental studies: 1) Radiative heat transport from the top of the bath is a significant portion of the total heat lost from the bath. However, for small changes in the bath temperature the change in transport by this path could be assumed to be proportional to the change in the bath temperature. 2) A very small portion of the heat input is lost through the thermocouple to its water-cooled holder. The thermal resistance and thermal capacity of the thermocouple protection tube are small, so the temperature of the thermocouple should follow closely that of the bath. 3) The remainder of the total heat lost from the bath will pass by conduction through the crucible to, and through, the other refractories, eventually being absorbed by the water-cooled induction coil or by the water-cooled sides and bottom of the enclosure. 4) The thermal resistance between the bath and crucible is very small. Thus the thermal capacity of the crucible will affect the temperature of the bath very soon after an addition of heat to the bath. 5) The thermal resistance between the crucible and the silica sleeve is large, especially if a radiation shield is placed in the gap. The effect of the thermal capacity of the sleeve thus will be significant only at longer times. The thermal resistance through the packing below the crucible also is large, so the packing and the silica sleeve will have similar effects on the behavior of the system. 6) A large temperature drop exists across the gap containing the water-cooled induction coil. Thus for relatively small changes in the thermal input to the bath, the refractories beyond the sleeve

Jan 1, 1970

By P. E. Baker

An experimental study of heat flow in steam flooding was carried out with steam displacing water in a plane-radial fluid-flow model. Temperature distributions in the model reservoir, overburden, and substratum were measured at frequent intervals during flooding by means of a fixed array of thermocouples. Heat losses to overburden and substratum and the division of heat between the steam and hot-water zones in the reservoir were calculated from the temperature data by performing numerical integrations over the appropriate volumes. Temperature profiles and heat distribution results are presented. Some results were (1) the fraction of injected heat that is lost to overburden and substratum, when expressed as a function of time, did not depend on injection rate; (2) a significant portion of the injected heat was contained in the hot-water zone ahead of and underlying the steam front in the reservoir. The division of heat between the steam and hot-water zones did depend on injection rate; and (3) considerable gravity override was observed. The experimental results are compared with those of several published theoretical studies of heat transfer in hot-fluid injection; approximate agreement on heat losses is found with some of the most idealized theories. A valid comparison cannot be made in regard to steam us hot-water zone; basic interpretation of the hot-water zone, in terms of a vertical steam front, is clouded by gravity override in the experiments. INTRODUCTION The experimental study reported here primarily concerns two problems of heat transfer in steam flooding that have economic and engineering importance. These are (1) the fraction of injected heat lost to the overburden and substratum, and (2) the division of the remaining heat between a zone containing steam and a zone of hot water at lower-than-boiling temperature. The volume of the steamed region, which has a direct effect on oil recovery, can be calculated readily from these results. Several valuable theoretical studies have been published on this problem, but no experimental tests of the theories have previously appeared. Tests were needed because the effects of the necessary simplifications in the theories could not be determined otherwise. The basic, untested theoretical problem is the effect of "decoupling" heat and mass transfer, and the resulting inability to include the effects of heat transfer and condensation on fluid flow. The theoretical problem solved so far has been a heat transfer problem in which fluid is present as a heat carrier and flows in a stipulated manner, either linear or plane-radial. The simplifications that have sometimes been made in regard to thermal conductivity by, for example, Marx and Langenheim,l Lauwerier2 and Thomas3 apparently do not have an important effect on heat loss calculations, although the results of the different methods disagree to a certain extent, as shown by Spillette4 and by Ramey.5 A recent paper by the author6 compared the results of experiments in hot-water flooding with several theoretical results and showed a rather poor agreement. It will be seen that the experimental heat loss results for steam flooding, however, show acceptable agreement. These comparisons are discussed in a later section. EXPERIMENTAL APPARATUS AND PROCEDURE The system studied was one in which a sand pack, initially water saturated and at a uniform temperature, was flooded with steam at a constant rate and temperature. The temperature distribution in the "reservoir" and adjacent "strata" was measured with an array of thermocouples, and heat losses were determined from these measurements. The sand pack contained no oil because the only concern of the experiments was heat flow, and it was important to have the flow pattern as simple

Jan 1, 1970

By H. H. Uhlig

SINCE its first mention in the literature in the eighteenth century1,2 the phenomenon of passivity in metals has stimulated much speculation and attendant controversy as to its nature and cause. No one of the numerous theories so far proposed has been generally accepted. ? Faraday,7 in 1836, associated the passivity of iron with a protective film over the surface of the metal, which materially prevents or slows down reaction with corrosive environments. His theory was that oxidizing acids like nitric acid form an unstable oxygen or oxide layer over the iron surface, which protects the underlying metal from further attack. This concept was simple yet plausible, and without alteration has frequently been assigned in present-day discussions as explanation of the passivity of many metals. With the advent in recent times of stainless steels, it is not surprising that this oxide film theory of passivity proposed by Faraday has been used to explain the phenomenal corrosion resistance of stainless steels and other passive alloys. The passive alloys, such as the chrome-iron alloys, are supposedly covered with a protective oxide film, which forms on exposure of the alloy to air, is extremely stable and self-healing, and accounts for the remarkable resistance of these alloys to corrosion. Within the past few years, several investigators, following the theory of film protection, have attempted to gauge the resistance of the supposed film on steels. Brennert8 and Donker and Dengg9 determined the poten-tial at which a negative ion (e.g., Cl-) moving in an electric field reacted with the metal anode, as detected by increased current flow or change in potential of the steel electrode in an electrolytic cell. The potential corresponding to reaction Brennert called the film break-through potential.

Jan 1, 1939

By N. S. Stoloff, M. Gensamer

The effects of temperature, grain size, and magnesium content on the strength and ductility of cadmium were studied in the range -269° to 23 °C. A sharp drop in ductility between -140° and -190°C marked a transition in fracture mode from ductile shear to inter gvanular fracture. The addition of up to 15.35 wt pct Mg in solid solution raised the transition temperature, and for two compositions produced basal cleavages. The relatively high ductility of unalloyed cadmium at cryogenic temperatures is attributed to temperature independence of the yield stress and the absence of dislocation locking. ALTHOUGH numerous studies have been made of the mechanical properties of cadmium single crystals,1-5 no comprehensive investigation of deformation and fracture in polycrystalline cadmium has been carried out. This investigation was initiated to determine the mechanisms of deformation and fracture in polycrystalline cadmium, and to attempt to correlate these mechanisms with the behavior of other metals of hexagonal close-packed structure. A second objective of this work was to determine whether the slip systems and mode of fracture of polycrystalline cadmium could be altered by reduction of the axial ratio, which is 1.886, through alloying. Dorn and co-workers' have been able to induce prismatic slip in magnesium through alloying to reduce the axial ratio. Single crystals of cadmium are so highly ductile that glide strains of 400 pct are observed at room temperature, and 80 pct at -269°c.l Failure in every reported case is by necking down and shearing off of the crystal. Cleavage in cadmium single crystals has never been observed. Magnusson and aldwin reported a ductile to brittle transition for polycrystalline cadmium at about —160 C for specimens tested at a strain rate of 0.05 in. per in. per min in tension. However, even at -196° substantial ductility was retained. The transition temperature was strain rate dependent, impact loading at 19,000 in. per in. per min raising the transition temperature to about -85°C while leaving the low temperature ductility unchanged. No information was given on microstructures or fracture mode, nor were stress-strain characteristics reported. In the present investigation, tensile tests were carried out on polycrystalline cadmium and solid solution Cd-Mg alloys to determine flow stresses, work-hardening behavior, fracture strength, and fracture ductility. Variables employed included temperature, alloy content (and c/a ratio), and grain size.Some compression data also have been obtained for comparison purposes. I) EXPERIMENTAL PROCEDURES A) Polycrystalline Cadmium. Two purities of cadmium were employed in this investigation. Cadmium of 99.95 pct purity was supplied by Belmont Smelting and Refining Co. Cadmium of 99.99+ pct purity was supplied by American Smelting and Refining Co. Threaded cylindrical tensile specimens were machined to give approximately a 1/2 in. long straight gage section with a reduced diameter of about 0.110 in. Specimens were heat treated in evacuated pyrex capsules in the range 140" to 290°C to produce desired grain sizes. All specimens were polished in a solution containing 320 g Cr03 and 20 g NaS04 in 1000 cc of H20. Occasionally this solution caused staining of the specimen, in which case a further polish with a solution of one part HN03 and two parts H202 in two parts ethyl alcohol was employed.' Tensile testing was carried out on a screw-driven Instron machine, at a constant rate of crosshead movement, which for most tests was 0.01 in. per in. per min. Load vs time, and therefore load vs total strain, were recorded. Temperatures from -196" to -40°C were obtained by passing nitrogen gas through a copper coil immersed in liquid nitrogen, and then feeding the gas into a jacket around the specimen. Tests at -269°C were carried out in a helium cryostat, at a crosshead rate of 0.1 in. per in. per min, with specimens of 1 in. gage length. Compression specimens were tested in a jig similar to one designed by ilman. The jig was mounted on the under side of the Instron crosshead. Load was transmitted by means of a rod connected to a movable part of the jig at one end, and the load cell at the other end. A downward movement of the crosshead applied a compressive load to the specimen.

Jan 1, 1963

By Emmanuel P. Papadakis

Ultrasonic velocity measurements have been made to study the preferred orientation in cube-textured copper. Methods applicable to thin specimens were employed since the specimens were necessarily of sheet material. The measured velocities in various directions in the sheet differed from the corresponding values in single-crystal copper by 1 to 6 pet. The distribution of the deviations indicated that the align-ment of the (001) planes with the rolling plane was better than the alignment of the [100]and [010] directions with the rolling and transverse directions. Ultrasonic pole figures (velocity us orientation) are shown to be useful in the study of preferred orientation. THIS paper describes one set of experiments in a continuing study of preferred orientation in worked metals. This study has been undertaken to investigate the fundamental properties of metals when used as propagation media for ultrasonic waves. Many such materials are of current or potential use in ultrasonic delay lines. Fundamental studies on ultrasonic propagation parameters such as velocity, attenuation, and diffraction (beam spreading) are of importance in the design of delay lines, in the development of nondestructive testing methods, and in the study of materials themselves. Preferred orientation in worked poly-crystalline metals influences all three above-mentioned parameters, and hence is of particular importance. When polycrystalline metals are subjected to mechanical working, they develop textures dependent upon their crystal structure and the symmetry of the working operation.' The texture consists in the alignment of the crystallographic axes of the grains in preferred directions with respect to the symmetry axes of the working operation. Since the grains are elastically anisotropic, the elastic moduli of worked metals are anisotropic. Hence the velocities of elastic waves in worked metals depend on the directions of propagation and polarization. The worked metal may be thought of as taking on the elastic symmetry of a single crystal: so it possesses the same number of independent elastic moduli as the crystal class it simulates. In general, a worked metal does not adopt the crystalline symmetry of its own grains. For instance, most rolled sheet becomes effectively orthorhombic while all bar stock and wire develop hexagonal symmetry. However, certain metals with cubic crystal structure develop a cube texture upon rolling and annealing.= Nearly perfect alignment of [100]-type directions with the rolling direction, transverse direction, and rolling-plane norma1 can be achieved in certain fcc metals and alloys. These cube-textured rolled metals provide an excellent opportunity to test preferred orientation by means of elastic waves, since a worked metal with 100 pct cube texture would have elastic moduli identical to the moduli of its constituent metal. It is the purpose of this paper to present the results of an investigation upon cube-textured copper. Ultrasonic waves were used. The methods of measurement and the experimental results on the effective moduli will be given. The ultrasonic measurements will be shown to complement X-ray pole figures for the determination of preferred orientation in worked metals. EXPERIMENT To study cube - textured material, it was necessary to use thin-sheet material since a severe reduction in gage (95 to 99 pct) is necessary to produce cube texture. Special ultrasonic methods were needed to investigate the thin material at megacycle frequencies. A) Materials. The cube-textured material tested was a copper alloy containing 1 pct Zn. Specimens already measured for Young's modulus4 by Alers were kindly supplied by him. The specimens were slabs 3.00 by 0.25 in. cut from sheet 0.047 in. thick. The orientations of the long axes of the specimens with respect to the rolling direction were taken in 15-deg steps from 0 to 90 deg. B) Measurements. Two distinct experiments were performed to measure the phase velocity in these specimens. One measured the shear wave velocity for propagation in the 0.25-in. direction and polarization in the 3.00-in. direction. The other measured the velocity of both shear and longitudinal waves propagating in the thickness direction in the sheet. 1) Plate-Mode Measurements. The velocity of the zeroth-order shear mode5 was measured in the 0.25-in. direction in each strip. The specimens were ground thinner over half their length to assure that the first-order shear mode would be cut off below 6 Mc per sec, leaving the zeroth-order nondispersive shear mode as the only propagating mode. Piezoelectric ceramic transducers of 5 Mc per sec resonant frequency poled in their long direction were solder-bonded to the edges of the thin part of the slabs as in Fig. 1 after these edges had been made flat and parallel by fine grinding. These transducers produced waves polarized in the 3.00-in. direction and propa-

Jan 1, 1967

By W. Spencer Hutchinson

The experiments described in this paper were undertaken primarily for the purpose of measuring the quality of work done in screening and sorting in American concentrating-mills for Prof. Richards' work on Ore-Dressiag. For this purpose a series of samples of screened and sorted products was obtained from four different mills, and a plan was devised for sizing these products, and for tabular and graphic representation of the results. The results, together with discussions as to their significance, so far as they serve to interpret the quality of mill-work, have already been published in the above-mentioned work, and it is not the purpose of this paper to duplicate the work, except so far as is necessary to explain and illustrate methods and appliances. The sizing of coarse products was clone by sifting on screens of sheet-metal with round punched holes. These holes ranged in size from 64 mm. to 0.5 mm. in diameter. Below the smaller limit, punched metal, suitable for this work, was not obtainable, and the sizing was carried on by sifting on woven wire-sieves. The finest woven wire-cloth obtainable gave a hole 0.073 mm. square, and the finest silk bolting-cloth pave a pentagonal hole with an average diameter of 0.069 mm. Even these very fine screens served no useful purpose in sifting certain of the very fine classifier-products, of which all, or nearly all, passed through the finest screen. A new adaptation of a method of settling and decantation with water in beakers was therefore worked out, and by this means the sizing mas carried down to grains of a diameter as small as 0.012 mm. Description of Apparatus and Manipu1ntion.—Sieves of sheet-metal with round punched holes were used as far as practicable, chiefly because, as already explained, the primary object of the experiments was to test mill-work, and the mills had all used

Jan 1, 1905

By Frederick C. Hull, Robert F. Mehl, Robert A. Colton

IT is known that pearlite forms from austenite by a process of nucleation and growth, and that the rate of formation of pearlite may be described by a rate of nucleation and a rate of growth 12 The manner in which these two quantities operate to produce the observed isothermal reaction curve has been analyzed in a paper published in 1939 3 Two types of process were described (I) that in which nucleation occurs at the grain boundaries of the parent phase, with the nodules growing toward the centers of the grains, initially as hemispheres and then after impingement as roughly radial-columnar structures, and (2) that in which nucleation occurs generally, with the nodules growing to full spheres until impingement with other growing nodules restricts growth Both cases are met in the formation of pearlite from austenite (Fig 1),2,3 the former, occurring near the knee of the S-curve has been named "grain-boundary transformation," and the latter, occurring at temperatures near AeI, has been named "group-nodule transformation " In developing our knowledge of the factors that determine the rate of formation of pearlite from austenite, it is important''' to obtain data on the rate of nucleation and the rate of growth of pearlite Such data, when obtained near the knee of the S-curve, will furnish information of use in understanding the actors that affect hardenability, when obtained at higher temperatures, such data will be useful in understanding the behavior of steels that during heat-treatment react to pearlite 2 It is the purpose of this paper to present data on the rate of nucleation and the rate of growth of pearlite in dependence upon composition, grain size, temperature,, and the degree of homogeneity of the parent austenite The studies are restricted chiefly to plain carbon commercial steels PREVIOUS DATA ON RAID OF NUCLEATION AND RATE OF GROWTH Data on the rate of nucleation and the rate of growth of pearlite have been published by Scheil and Lange-Weise,5 by Mirkin and Blanter,6,7 by Mehl,1 and by Dorn, De Garmo and Flanigan22 It is difficult to interpret the data, for in most cases too little information is given on austenitizing temperatures and times, the state of homogeneity of the austenite (presence or absence of carbide, etc ), austenite grain size, and mode of formation of pearlite at the temperatures given

Jan 1, 1942

By H. M. Day, C. H. Mathewson

THE constitution of the system silver-mercury has attracted the attention of many investigators during the last two decades, but since their results are for the most part in poor agreement, there is little need for a review of their individual contributions. It remained for the very careful thermal and microscopic investigation of Murphy' in 1931 to give the constitutional diagram in its present and unquestioned form, which is shown in Fig. 1. He devised methods for taking cooling curves on alloys under high pressures and for the microscopic observation of alloys which contained liquid mercury as a structural constituent at ordinary temperatures. The compositions of the intermediate phases were confirmed and supplemented through X-ray analyses by Preston2 and Stenbeck.3 According to Murphy, at 276° C. silver is able to dissolve 44 to 45 weight per cent of mercury, which may increase at lower temperatures to about 50 per cent. Preston concluded that the saturation boundary occurred at 46 ± 2 per cent at 100° C. From the values reported in the literature, these are the only ones that may be accepted as lying even in. the right region. PREPARATION OF ALLOYS The silver used in the present investigation was supplied by the United States Metals Refining Co. through the courtesy of the Committee on Industrial Uses of Silver and, since a complete spectrographic and chemical analysis was furnished, no attempt was made to purify it or to further establish the impurities present. The analyses reported by the company are shown in Table 1. Milligan4 has found that the magnesium content is probably less than 0.0005 per cent.

Jan 1, 1938

By Larry Kaufman, Joan B. Berkowitz-Mattuck, Edward V. Claugherty

The oxidation characteristics of hafnium and zirconiunr diboride were measured between 1200 and 2200'K by a thermal- conductivity method which continuously ttzeasures the rate of reaction of oxygen with the diboride and by a metallographic air oridation method zuhich provides a measure of the total arr7ount of bovide conuerted to oxide for a given time interval. The oxidized specimens obtained from the tl~eritaal-coi~ductitrity method were also examined by quantitatire metal-lographic procedares. The significant results obtained in this investigation reveal that metal-rich compositions of lzafi~iutil diboride proride the most oxidation-resistatzt material up to 2000°K; hafnium diboride is tmre oxidation- resistant titan zirconium diboride at all tempevatures examined; the morphology of the oxide formed on H/B2 and Llie temperature coefficient qi. the oxidation rate constants change at the temperature of ttze monoclinic to tetragonal phase transition] in HfO2; the oxidation of neither HfB2 nor ZrB2, results iN catastrophic Jazlure at lorc. oxygen pressures; and pvefevetztial gvaLti boundary oxidation was not obsevued for either HfBi or ZYB, A comprehensive study of the high-temperature characteristics of refractory transition-metal di-borides is currently in progress. This program has included investigation of the physical, thermal, and thermodynamic properties of TiB2, ZrB2, HfB2, NbB2, and TaB2. In addition, aspects of the synthesis and fabrication of such materials have been studied. In view of the diverse nature of this research, a number of other laboratories have actively participated and contributed specific capabilities for analysis and characterization of these materials. As a consequence, an extensive description of the relevant properties of these compounds has emerged which is central in evaluating their high-temperature (1200" to 2500°K) performance. To date, information on thermodynamic stability, specific heat, and vaporization characteristics,1 hot hardness and electrical resistivity,1, 3 therma1 expansion:'4 and thermal conductivity 1, 5 has been presented. This information has been generated on materials of the highest purity (98.5 to 99.9 wt pct Me + B) and density currently available. Samples fabricated by zone melting6 and high-pressure hot pressing"3'7 techniques have been used to generate suitable specimens for all of the aforementioned studies. dation characteristics of the most oxidation-resistant of these materials, hafnium and zirconium diboride, is presented and a description of the synthesis and the experimental procedures used to prepare and characterize specimens is given. The high-temperature range under consideration (1200" to 2200°K) and the known dependence of oxidation characteristics on sample chemistry, density, and oxidation conditions required a close coupling of the synthesis, fabrication, and evaluation procedures.8 This was accomplished by continual surveillance of chemical composition of starting materials before and after specimen fabrication and by evaluation of density, phase constitution, and microstructural features prior to and after oxidation exposure. I) PROCUREMENT AND CHARACTERIZATION OF STARTING MATERIALS In view of the current state of the art in fabricating refractory boride materials, the methods used in preparing samples for the present study are given in detail as follows: starting materials were purchased in high-purity powder form and fabricated by high-pressure hot pressing into 0.40 by 1.00 in. bars from which oxidation specimens were obtained. The hafnium diboride used in this study was purchased from Wah Chang Corp.; the zirconium diboride from U.S. Borax and Chemical Co. These powders were routinely characterized by quantitative chemical analyses for metal, boron, carbon, oxygen, nitrogen, and iron, by qualitative emission-spectrographic analysis for trace impurities, by X-ray procedures for extraneous phase identification, and by powder densitometry for comparison with X-ray (theoretical) density. Hafnium and zirconium metal and elemental boron were also purchased as high-purity powders and characterized for impurities by emission-spectrographic analyses. The hafnium diboride was procured in three shipments which were designated as HfBl.g7(1), HfB1.88(2A), and HfB2.12(2). The indicated stoichiometry is based on the atomic ratio of total boron to total hafnium; the number in parentheses identifies the shipment number. Shipment 1 was 5 1b, shipment 2A, 1 1b, and shipment 2, 8 1b. The zirconium diboride was procured as a 20-1b shipment and designated as ZrB1.89(1). A small quantity of purified zirconium diboride was also supplied and designated ZrB1, 9(P). The averaged results for chemical analyses which were generally performed according to the procedures set forth in the compilation by KrieGe9 are presented in Table I. Qualitative spectrographic analyses indicated that Ca, Cr, Ti, Si, Zr (in H~B~), and A1 were present at levels between 0.01 and 0.10 wt pct. Other metallic elements were found to be less than 0.01 wt pct. Since it is virtually impossible to purchase these materials in the desired quantities (5 to 20 lb) as single-phase compounds it is necessary to obtain

Jan 1, 1968

By Ross Glanville

INTRODUCTION The Optimum Production Rate (OPR) is one of the most important parameters in the evaluation of a mineral deposit. The OPR can also be expressed as the Optimum Mine Life (OML) in years since the expected mine life is determined by dividing the OPR per year into the estimated ore reserves. Unfortunately, very little time and effort has been directed towards the determination of the OPR. Instead, "rules of thumb" are often applied to select a mine life without due consideration of the economic implications of such a selection. A "justification" for a particular production rate is often based on a pre-conceived arbitrary requirement for a mine life of 5, 10, or 15 years, for example. In this paper it is demonstrated that such arbitrary selections for high-grade/low-tonnage mines (such as many underground gold/silver deposits) often lead to sub-optimal results. In fact, an apparently uneconomic deposit at an arbitrary production rate may be economic at the OPR. Consequently, investment opportunities may be overlooked if one analyzes mine properties based on arbitrary production rates. This paper analyzes the interrelationships of variables such as production rates, capital and operating costs, cut-off grades, discount rates, metal prices, etc. The analysis shows that the OML for high-grade/low-tonnage deposits is often in the range of two to four years. Although such mine lives intuitively appear too short to many individuals, it should be noted that, in the past, much of the mining industry became familiar with the economics of large scale mining operations. The rules of thumb developed for such large scale operations should not be applied to high-grade/low-tonnage mines such as many of the underground gold deposits. DEFINITION OF OPTIMUM PRODUCTION RATE The OPR is selected on the basis of maximizing the net present value of the after-tax cash flows. However, as discussed later in this paper, the production rate selected for a particular mine may be somewhat higher or lower than the theoretical OPR as a result of other variables such as: 1) the probability or expectation of additional reserves being discovered 2) the likelihood of being able to custom mill nearby deposits owned by others 3) the configuration or attitude of the orebody, which may place upper limits on the production rate 4) the residual, or salvage values, of the mine/mill facilities COMPARISON BETWEEN DIFFERENT PRODUCTION RATES For an orebody with definite physical cutoffs*, or boundaries (such as faults or unconformities), the total ore reserves at different production rates may be identical. Consequently, for such an orebody, varying production rates result in differing mine lives. Although the metallurgical recoveries, the mine dilution, and other similar physical parameters may vary slightly at different production rates, the major differences are the capital costs and operating costs per ton. The ramifications of these differences are especially important at low production rates (up to approximately 1000 tons per day), but can also be significant at higher production rates.

Jan 1, 1985

By Betty M. Miller

INTRODUCTION In September 1974 the Resource Appraisal Group of the Branch of Oil and Gas Resources, U. S. Geological Survey, was asked to aid the Federal Energy Administration (FEA) in its legal responsibility to generate by June 1975 an independent appraisal of the undiscovered oil and gas resources of the United States, both onshore and offshore. As a result, the Resource Appraisal Group accelerated its ongoing efforts to develop sound appraisal methods and procedures that would permit the systematic collection and evaluation of basic data from petroleum provinces throughout the Nation. The results of this independent appraisal of the Nation's conventional oil and natural gas resources were published by the U. S. Geological Survey as Circular 725, June 1975 (1). The estimates in this report of undiscovered recoverable oil and gas resources for the United States were made: (1) by carefully re- viewing a large amount of geological and geophysical information gathered on more than 100 different provinces by over 70 geologists within the Survey; (2) by applying a variety of resource appraisal techniques to each potential petroleum province; and (3) by application of subjective probability procedures to group appraisals for each petroleum province. These methods provide a range of estimates which are summarized in terms of low, high and mean values for the various provinces and groups of provinces, or regions. The basic data and procedures used are documented and are being incorporated into a dynamic, data- intensive system that can be upgraded, updated and reevaluated periodically. These data are open to public inspection. In this study, the primary emphasis was placed on conventional crude oil and natural gas in the onshore provinces and the provinces on the continental shelf out to water depths of 200 metres; estimates

Jan 1, 1977

By Robert M. Dreyer

During the past two decades, synthetic abrasives have taken over successively greater percentages of the high-grade abrasive market, so that now, with the exception of natural diamonds (discussed in section 3.15.4C of this chapter), the importance of natural high-grade abrasives is negligible. The predominance of synthetic abrasives is indicated in Table 15.4A.1. This shows that the 1968 value of domestically produced synthetic abrasives (excluding synthetic diamonds) was over $80 million, whereas the value of garnet, the largest domestically produced, natural high-grade abrasive, was less -than $2 million. The major synthetic abrasives (other than synthetic diamonds) are: alumina, silicon carbide, boron carbide, tungsten carbide, and metallic oxides, including various iron oxides. A major advantage of synthetic abrasives is that the size and shape of grain can be closely controlled during manufacture. Although Table 15.4A.1 gives the average price of synthetic abrasives, such averages are of somewhat limited value. This is because the actual price varies within wide limits, depending on composition, hardness, size, and shape of grain. In 1968 the approximate total consumption of abrasives in the United States was valued at about $200 million, of which about two-fifths was in the form of synthetic abrasives (other than diamonds), one-third in synthetic diamonds, and the remainder in natural diamonds. Natural abrasive products, such as silica sand, tripoli, and pumice, are important in the low-cost abrasive field. Of the low-cost abrasives, silica sand continues to be the most important, with domestic production of about 300,000 tons at a value of $1.8 million (see Table 15.4A.1). In general, the lower the sales price of the abrasive product, the more limited is the market which can be served from a given production center. Each abrasive has applications for which it is especially useful, but there is a continual struggle among abrasive suppliers to induce substitution of one product for another. Such substitution can be stimulated by changes in method of preparation affecting hardness, shape, and size of grain.

Jan 1, 1976

By Blamey Stevens

(Butte Meeting, August, 1913.) THE following paper aims to make a full explanation of the phenomena of rock jointing: It may be unnecessary to give any general description of what are termed joints in rocks, but Professor Geikie's clear and faithful generalizations are so illuminating that no excuse need be given. for introducing the following and other quotations into this paper "Almost all rocks are traversed by vertical or highly inclined divisional planes termed joints. These have been regarded as due in some way to contraction during consolidation (fissures of retreat) ; and this is no doubt their origin in innumerable cases. But, on the other hand, their frequent regularity and persistence across materials of very varying texture suggest rather the effects of internal pressure and movement within the crust." 1 General Explanation.-In this paper I show that the phenomenon of jointing may to a large extent be accounted for by the pressure of the water contained in the pores of the rock. To understand this, each constituent grain of the porous material may be considered to be separately compressed by the water which submerges it. As all the grains are held together by cohesion, the whole mass is contracted by this pressure. In an indefinitely extended mass, however, there must be a limit to the possible contraction without rupture, because the material is restrained from moving freely by other material around its boundaries. The mass of rock thus becomes broken up. This phenomenon is known as '" shrinkage " jointing. The term " shrinkage " is an apt one, if it be understood that the shrinkage of the rock is often brought about by change of stress. Stresses.-The compressive component of water stress on the individual grains is evidently the same as that of the water with which it is in contact. This is so, both before and after the jointing is formed. Before the jointing is formed there is, however, a tensile stress in one or more directions which keeps the material from contracting. .

Jan 7, 1913

By Joseph C. Mead, James R. Cudworth

THE Birmingham district of Alabama has utilized the slag from its blast furnaces consistently since the earliest development of the slag industry. Today there are producers of slag cement who started business in 1900, and who have, under a progressive policy, expanded the number of their products to meet present demands. There are producers of slag aggregates and other crushed slag products who have been successful for periods of over thirty years. There are at the present two companies, Cheney Lime and Cement Co. and the Southern Cement Co., manufacturing puzzolan cement; two companies, Birmingham Slag Co. and Woodstock Slag Co., making slag aggregates and by-products; one company, Tennessee Coal, Iron and Railway Co., a subsidiary of the U. S. Steel Corporation, producing ground open-hearth basic slag for soil conditioning. Two companies, the Sloss Sheffield Steel and Iron Co. and the Woodstock Slag Co., make slag concrete in ready-mix plants and one company, the Superock Company, manufactures fine and coarse slag aggregates under a new granulation process. No Portland cement is made with slag as an ingredient, because dolomite is used so extensively as a blast-furnace flux that the magnesium content of the slag is excessive. Sources Of Slag In the Birmingham district there are 22 blast furnaces, of which the majority are in blast. The present production is 165,000 tons of pig iron monthly; the production in 1935 was 1,297,960 gross tons1. There are also two blast furnaces at Gadsden and one ferroalloy electric furnace at Anniston. From these two sources is obtained slag to approximately 1.1 tons per ton of pig iron.

Jan 1, 1937

By Wilbur T. Stuart

TO assist the mining industry in attacking problems of water control, the U. S. Geological Survey has begun a program of research in mining hydrology. In certain fundamental respects water control is similar to development of water supplies from wells or to the drainage of agricultural lands, as many of the tools developed in recent years for quantitative ground-water problems are applicable, with modification, to mine-water problems. In 1952 a 30-day pumping test conducted jointly by the Eureka Corp. Ltd. and the Defense Minerals Exploration Agency provided an opportunity to gain knowledge concerning water movements around a flooded mine shaft. The methods of analyzing the data may be used as a guide for the evaluation of similar problems elsewhere. The Fad shaft of the Eureka Corp. is on Ruby Hill, 1 1/2 miles west of Eureka, Nev. The shaft was completed at a depth of 2465 ft in November 1947 at a site adjacent to the downfaulted block in which the ore was found. As the drift on the 2250 level progressed toward the ore zone, a large flow of water was encountered after the Martin fault was intersected. This flow exceeded the installed pump capacity, and an unsuccessful attempt to recover the shaft and the 2250 level was made in 1948.1, 2 Geology and Hydrology: The complex structure of Ruby Hill is that of an anticline broken first by thrust faulting and later by normal faults. The present orebody comprises several mineralized zones within a block of the Eldorado limestone of middle Cambrian age which was downfaulted 1400 to 1600 ft, and it may be related to a similar body mined at a higher level south of the Ruby Hill fault. At the depth of the largest zone of ore the block is roughly rectangular in shape, about 1000 ft wide and 1500 ft long, and dips about 30" NE, see Fig. 1. It is apparently bounded on the south by the Ruby Hill fault, on the east by the Jackson fault, on the north by the Martin fault, and the west by the Bowman fault. Within the block, but between the Ruby Hill and the Martin faults, are the Office and Adams Hills faults; west of the block and the Bowman fault are the Albion and Spring Valley faults. There are many conflicting reports concerning the water-yielding characteristics of the Eldorado limestone and the condition of the fault zones, that is, whether they are open or tight. However, the diamond-drill records indicate that open spaces as much as 2 or 3 ft across were encountered, and considerable cementing and lining of holes was necessary to maintain circulation of drilling fluid. There is also evidence that the Eldorado limestone was cavernous where it was mined in the early days south of the Ruby Hill fault. At the site of the Fad shaft the formations encountered from the surface down included the Pogonip limestone, Dunderberg shale, Hamburg limestone, and Secret Canyon shale. These formations did not yield large quantities of water to the shaft. The Pogonip limestone, which appears to be permeable and might yield water elsewhere, is above the water table in the vicinity of the shaft. The Secret Canyon shale, immediately overlying the Eldorado in some places but in most places separated from it by the Geddes limestone,3 is apparently tight and does not transmit water. During the 30-day test period the shale briefly confined the water in the underlying formations so that artesian conditions were observed in drillholes E and F, which are cased into the Eldorado limestone, whereas unconfined conditions were observed in drillholes B, C, and D, which were open to the shale. The Geddes limestone, which normally lies between the Secret Canyon shale and the Eldorado limestone, was not encountered in the Fad shaft. The Geddes, a flaggy, fractured limestone, is reported capable of yielding large volumes of water. Water stored in the interstices of this thin-bedded limestone within the Ruby Hill fault zone on the 1200 level of the Locan shaft drowned the pumps in 1923 when the Richmond-Eureka Mining Co. attempted to explore the area along the fault. Eldorado limestone was not encountered in the Fad shaft. In the ore-block area the Eldorado limestone was not entirely offset from other water-yielding formations by movement along the Bowman fault; therefore it may be hydraulically connected with the other formations. Adjacent to the Ruby Hill, Jackson, and Martin faults, the Eldorado lies in contact with other possible water-yielding formations. One of these, the Prospect Mountain quartzite, is separated from the Eldorado by thin, sheared, and broken beds of the Geddes within the Ruby Hill fault zone. A limited examination by the author of the Prospect Mountain quartzite in the Richmond mine at a higher level and south of the Ruby Hill fault indicates that the quartzite is poorly permeable. The monzonite mass south of the quartzite would be a further barrier to the flow of water. The poor permeability of this area is substantiated by records of levels at which water was encountered south of the Ruby Hill fault. In view of the normally low rate of ground-water recharge, if this desert area had been permeable, water levels could not have been maintained at altitudes of many hundred feet above the present water table west and north of Ruby Hill. Thus the ore-bearing block of Eldorado limestone is in contact with possible water-yielding rocks on at least two sides, and if the fault zones are possible conduits for water circulation the geologic and hydrologic conditions are suitable for the infinite-aquifer type of analysis as used and modified here. History of Pumping: During sinking of the Fad shaft a maximum pumping rate of 1500 gpm kept the shaft dewatered sufficiently, but in March 1948, after the 2250 level drift passed through the Martin fault into the Eldorado limestone, the pumps and shaft were flooded. Subsequently additional pump-

Jan 1, 1956