Search Documents

By Edwin Ludlow

ROUNDING out a year of improved organization, substantial accomplishment and strengthened purpose, the American Engineering Council of the Federated American Engineering Societies held its first annual meeting at the Cosmos Club, Washing-ton, Jan. 5 and 6, Dean Mortimer E. Cooley of the University of Michigan, president of, the Council, presiding. Officers were-chosen, the work of the past year was reviewed and discussed, action was taken on important matters of public and technical service, new financial arrangements were put into effect, committees were named, new policies were sanctioned and old ones reshaped, and a broad and definite program was out-lined for the next twelve months. A leading event of the meeting was a dinner in honor of Herbert Hoover, who, addressing the members of the Council and their guests at the University Club, praised the work of the Committee on Elimination of Waste in Industry as a great and lasting public service, pointed the way for new engineering effort in the public interest, and expressed renewed devotion to the ideals of the Council. Resolutions of appreciation of the service of the Secretary of Commerce were presented to Mr. Hoover.

Jan 2, 1922

By H. C. Howarth

THIS paper gives observations on ground movement and subsidence resulting from pillar drawing in the Lick Run section of Montour No. 10 mine of the Pittsburgh Coal Co. adjacent to solid coal owned by the U. S. Bureau of Mines at its Experimental mine in Snowden Township, Allegheny County, Pennsylvania. The investigation was planned by George S. Rice, chief mining engineer of the Bureau, who arranged the necessary cooperation with Dr. L. E. Young, vice president of the Pittsburgh Coal Co. Engineers of that company placed permanent monuments on the surface to establish the boundaries of the coal owned by the Bureau and to furnish fixed points to which all levels were referred. Engineers of the Experimental mine staff then covered the ground under observation with a checkerwork of monuments made of oak pegs set into the ground at 50-ft. intervals in two directions at right angles to each other. The level of these pegs was determined first from Dec. 16 to 30, 1929; again from May 25 to June 5, 1930, and finally from July 7 to 15, 1931. Observations were then discontinued because work had been stopped temporarily in this part on Montour 10 mine.

Jan 1, 1933

By E. S. Greiner

Germanium and silicon have been plastically deformed in torsion at elevated temperatures. Slip took place on the four {Ill} planes. Dislocations, revealed by etch pits on a (111) face, occurred in rows that were traces of operative slip planes. THE plastic deformation of germanium and silicon by bending and tension at elevated temperatures has been reported by Gallagher.&apos; Transla-tional slip during plastic flow in these materials, according to Gallagher&apos; and Treuting,&apos; occurs on (111) planes. Recent work by Treuting&apos; indicates the direction of slip to be <1l0>. The present paper describes the plastic flow characteristics of germanium and silicon deformed by torsion. Torsional deformation was accomplished by twisting 1/4x1/4x2 in. specimens held in molybdenum grips and contained in an atmosphere of helium in a transparent quartz tube and heated by an external resistance furnace. The angular displacements were measured on a graduated circle with a pointer attached to the movable grip. Temperatures were measured with a chromel-alumel couple; the hot junction was within the quartz tube and in close proximity to the specimen. Photographs of samples of germanium and silicon twisted at 850" and 1180°C, respectively, are shown in Fig. 1. The germanium was twisted 230" per in. and the silicon 80" per in. These deformations are larger than those used in experiments to be described later and are presented only to emphasize the extensive plasticity of these materials. Germanium A single crystal specimen of germanium (n-type, 7 ohm-cm resistivity) with a (111) plane normal within 3" of the torsion axis, Fig. 2, was chemically polished with CP-4 solution" and then twisted 9" during the twisting of these specimens of germanium, the slip lines from the (lli) plane should have appeared in the four lateral faces instead of in only two. Perhaps the absence of rotational slip is brought about by the square cross-section. A cylindrical specimen would have a more uniform stress distribution in torsion than one with a square cross-section, and may deform by rotational slip. A specimen of germanium (n-type, 5 ohm-cm resistivity) twisted less than 8" per in. at 550°C, was cut to expose the (111) face 19" 28&apos; from the torsion axis, Fig. 4a. This face, after metallographic

Jan 1, 1956

By M. van Swaay, C. E. Birchenall

Palladium has a large capacity for the dissolution or occlusion of hydrogen; the gas also diffuses very rapidly through the metal. Palladium thimbles are widely used in the laboratory for purification of hydrogen by diffusion. The use of palladium filters could be extended to several large-scale applications if greater stability of the permeation process could be attained. In this paper a number of aspects contributing toward this goal are discussed, and new data on solubility and diffusivity are given. Palladium sheets of 0.005, 0.010, or 0.020 in. thickness were prepared by three procedures: casting and rolling, sintering palladium powder, and sintering palladium powder to which 0.1 pct thorium oxide had been added. Half-inch diam circular specimens were cut and clamped in a stainless steel holder provided with knife edges to seal the palladium sheet with soft copper gaskets. The seals were tested for leaks at l0-5 mm Hg. No difficulties from this source were encountered even after many temperature cycles in the system. The holder was silver-soldered to Kovar-glass seals and attached to the system through glass ball joints. Each joint was sealed with Apiezon wax and was adjacent to a cold trap. In several experiments the holders were fused directly into the system, eliminating the ball joints, to show that the wax did not affect the filter. Three filter holders were supported in holes in a stainless steel cylinder, which also acted as a temperature equalizing block inside the resistance wound furnace. The measuring thermocouple was inserted in one of the holders. A potentiometric controller with control thermocouple on the furnace heater winding maintained ± 0.2oC. Electrolytic hydrogen was purified and stored as shown in the flow diagram, Fig. 1. It could be admitted to either or both sides of the palladium specimens. Only a mechanical pump was used, for even high pumping speeds would not bring the pressure on the off-gas side of the filter below 10 to 50p Hg owing to the rapid hydrogen flow through the filters. A series of steady-state permeability studies allowed identification of several conditions of permeability loss. A constant fore pressure was maintained while the low-pressure face was pumped. After enough time had elapsed for a steady flow to be established the pump was cut off, and the rate of pressure increase in a thermostated bulb was measured to determine the flow rate. The time delay method of Daynes1,9 was adopted since it offered the possibility of determining solubilities and diffusivities. For each measurement both sides of the filter were evacuated for 15 min, which gave about 10-4mm Hg residual pressure. Hydrogen was admitted to one side or the other of the filter at a fixed pressure. The pressure on the off-gas side was observed as a function of time. A

Jan 1, 1961

By Werner Engelmaier

Constant-strain rotating-bending fatigue tests were conducted on 2024-T3 aluminum alloy constant-strain McAdams-type specimens in ultrahigh vacuum, 10-lo Torr, and in atmospheric air. In the elastic strain range the ratio of vacuum-to-air fatigue life varied from about 10 at a maximum bending stress of 37 ksi to near unity at the endurance limit. After 10 pct of the fatigue life, intergvanular microcracks appeared on the surface which did not appreciably propagate further until the last 5 pct of the fatigue life, where trans-granular cracks propagating first in slip-plane cracking and then in the stress-dominated mode led to failure. No reduction in residual tensile strength resulted from the fatigue of the specimens short of fracture. The mechanism governing the fatigue life operates between the occurrence of the intergranular microcracks and the initiation of the trans granular cracks. MORE than forty years ago, Mc Adam&apos; and Haigh2 published the first systematic studies showing that the fatigue properties of metals were greatly affected by environments. Gough and sopwith3 found in a later study that the fatigue life of metals subject to corrosion can be substantially increased by reducing the atmospheric pressure. This and their later work4&apos;5 was, however, done in a vacuum of only 10~3 Torr. Subsequent studies6-&apos; at a vacuum of 10- Torr showed that water vapor is the primary agent affecting the fatigue properties of aluminum alloys. Only recently was ultrahigh vacuum used for fatigue studied.l Various theories have been put forward to explain this phenomenon. Wadsworth and Hutchings12 postulated that cracks form very early in the test and that the chemical attack by the corrosive components of the atmosphere at the root of the cracks enhances the speed of the crack propagation. They also noted that chemisorbed layers of gas on the fresh crack surfaces prevent cold welding of the crack and make the separation irreversible. Ham and Reichenbach, on the other hand, reported that their specimens showed no cracks after a run in vacuum, even though the runs were long enough to have caused the specimen to fracture in atmospheric air. They also reported that in argon at 0.14 Torr the fatigue life was about 5 times longer than at 7 X lo-&apos; Torr. Jacisinll reported that fatigue tests in dry nitrogen showed results close to those obtained in ultrahigh vacuum. The present experiment was designed to determine the extent to which cumulative fatigue damage, i.e., the accumulation of length of fatigue cracks, reduces the residual static tensile strength of an aluminum alloy in both ultrahigh vacuum and atmospheric air and to obtain fatigue-life data for this aluminum alloy at various strains. It was also hoped that information ex- tracted from these data might support one of the previously mentioned theories. 1) EXPERIMENT Test Specimens. The material tested was commer-cial 2024-T3 aluminum alloy. In addition to aluminum, this alloy contains approximately 4.4 pct Cu, 0.5 pct Fe, 0.5 pct Si, 0.6 pct Mn, 1.5 pct Mg, plus smaller amounts of other elements.13 Some typical mechanical properties of this aluminum alloy are listed in Table I.&apos;~ The material was used in the as-received condition, i.e., solution-treated and cold-worked. Mc Adam-type1&apos; constant-stress specimens and notched fatigue specimens were machined from 4 -in. -diam rods, Fig. 1. The critical section of the McAdam-type samples was polished with a 45-deg spiral motion to a No. 8 microfinish. The notch in the notched specimens was machined on a lathe with a forming

Jan 1, 1969

By Harold Markus, Gerhard Derge

THE first paper1 of this series described a technique of careful surface preparation by means of which reproducible results may be obtained from potential measurements of the behavior of tin in carbonate solutions with a pH range from 8.4 to 11.2. It then went on to establish the behavior of pure tin electrodes under these conditions and showed that the metal remains active at all times, though the steady potential attained after several hours decreases from I.I2[t] volts at a pH of 12.6 to 0.6 volts at a pH of 8.4. This behavior may serve as a norm with which all other data can be compared. In the second paper,2 small amounts of other anions were added to the carbonate solutions and the conclusion was reached that the common impurities encountered in alkaline materials packaged in tin do not increase corrosion. In fact, in some cases these anions may actually promote the formation of protective films. The present paper rounds out this survey by presenting data on the influence of cations added to the carbonate solutions, as well as the effect of alloy additions to the tin. In many cases the potential data are supplemented with weight-loss measurements. Information is also presented on the effects of some additional anions, the influence of gases above the electrolyte, the behavior of high-purity tin, and the effect of atmospheric oxidation on the corrosion resistance of the above-named alloys. Analysis of the entire body of data discloses some general rules applicable to corrosion in carbonate solutions. The experimental methods used are the same as those previously described. EXPERIMENTAL DATA Cations.-The carbonates of the cations K+, Li+, NH4+, which are soluble, were studied in the same way as the anions, by adding 0.01 mol of the metal carbonate to one liter of 0.2 M sodium carbonate solution, pH 11.2, or to 0.1 M sodium bicarbonate, pH 8.4. The other metallic carbonates are only slightly soluble, of the order of 0 7-3 mols per liter or less, and the sodium carbonate solutions were saturated by adding excess reagent several days before the experiment, shaking frequently, and filtering just before use. The chemicals were c.p. grade in each case except the indium salt. This salt was prepared by solution of the metal in hydrochloric acid and precipitation by addition of Na2CO3. These cations may be divided into two classes, according to their effect on the potential behavior of the tin: (I) normal, (2) passive. To offer a basis of comparison, curves I of Figs. I and 2 are given to illustrate the behavior of tin in carbonate solutions saturated with CaCO3. These curves are the

Jan 1, 1941

By Henry F. Cooper, Scott E. Blouin

Large jacking test procedures that have been applied to obtain static in-situ rock properties (Ref. 1) have shown that the in-situ rock modulus and strength can be considerably less than what would be obtained from laboratory tests on intact samples. This trend is also expected to be true for dynamic properties, but few dynamic in- situ rock property tests have been conducted. During the past several years, high explosive test procedures have been developed to simulate the airblast and direct induced ground motions (Ref. 2) produced by nuclear explosions . These test procedures load large volumes (up to 10 7 f t3) of the earth with stress levels sufficiently high to produc5 feet of particle displacement over surface areas up to l0 5 ft2. This paper discusses some of the data obtained, and the implications of these results for our understanding of the dynamic response of in-situ rock. DESCRIPTION OF TEST PROCEDURES As shown in Fig. 1, the High Explosive Simulation Technique (HEST) consists of a cavity of uniform height bounded on the sides by a soil berm, above by an overburden of uniform thickness, and below by the test bed on the earth&apos;s surface. Horizontal racks of detonating cord are placed in the cavity and detonated at one end of the test bed. This detonation produces an explosive wave that propagates across the test bed, loading the earth with an overpressure pulse that decays with time because of the compression and lifting of the overburden. Since 1964, there have been approximately 40 such tests on test bed areas ranging from a few hundred to l0 5 sq ft., simulating peak overpressure conditions between about 100 and 6000 psi and specific impulses between a few and over 100 psi-sec.

Jan 1, 1971

By George Bain

SOME problems concomitant with commercial exploitation of marble are presented as examples of interesting, useful and profitable fields for application of scientific knowledge. The marble industry is only one such field and is selected because its varying new aspects are familiar to the author. However, what is true for marble is equally so in principle for many industrial minerals. The problems of any stone industry are to maintain markets, create new outlets for stone already in demand, and develop varied uses for varieties that are not so popular. Here the geologist has a different role from most of his colleagues in metal mining. The producing branch may ask about the expectable variation in thickness or size of a deposit as development proceeds. The stock department may call for the available amount of a given type of stone before accepting a large order. The sales force requires data on the use for stone from certain parts of deposits in order to divert grades to the most suitable use. The service depart-ment wants defects rectified and the cause determined to avoid recurrence. The mills want data on durability and cutting quality of abrasives. The geologist occupies no special department; he is on general call, as may be illustrated by a few types of problems that may be classified as: (1) dominantly geological in character, (2) dominantly chemical in character, (3) dominantly physical in character.

Jan 1, 1940

By Hsun Hu, R. S. Cline

The effect of rate of deformation on texture formatiotz has been studied with cube-oriented single crystals of 3 pct Si-Fe, compressed 80 pct at two widely different rates. Compression at a low rate (crosshead speed, 0.1 ipm) produces large orienta-tional changes and coarse deformation bands, whereas little change in orientation is observed, particularly at the surface of the crystal, when compressed at a high rate (impact velocity, -500 ips). Thin plates of mechanical twins are produced at the high rate, but their contribution to the deformation texture is practically negligible. The crystal deformed at a high rate has a lower hardness and a more uniform dislocation structure and is morc resistant to recrystallization. There is also a dilference in the recrystallization texture between the slowly and rapidly compressed crystals. These results indicate that plastic flow is less "turbulent" at high strain rates than at low strain ratcs. THE behavior of metals under high-speed deformation has been the subject of wide study in the past decade. Most of these works were concerned with mechanical properties during testing at high rates of loading, the resulting structures, and the theoretical aspects of the observed phenomena. The present status of knowledge and research activities in this field has been documented in recent publications.17&apos; There is, however, very little information available in the literature concerning the effect of high-speed deformation on the texture formation in metals. The possibility of an effect of rate of deformation on texture is suggested by the microstructural differences observed between normally and very rapidly deformed samples. Aside from the strong tendency for twinning (and phase transformation in certain metals) in high-speed deformation, the slip-line patterns and the dislocation configurations show marked differences as a result of large differences in the strain rates. For instance, in mild steel in static and dynamic compression, Campbell and co-worker3,4 observed that coarse slip occurred on several systems in specimens deformed at normal strain rates, whereas specimens deformed rapidly showed only fine slip on fewer systems, the slip-line pattern being very similar to that in specimens deformed at low temperatures and at normal strain rates. The absence of multiple slip was also noticed by Dieter5 in shock-loaded nickel. The dislocation configuration in an iron shock loaded at 70 kbar pressure was shown by Leslie et al.6 to be similar to that produced by light rolling at low temperature—the dislocation lines were mostly straight and uniformly distributed. These observations suggest that the mode of deformation at high strain rates is notably different from that at low strain rates. Consequently, the nature and the extent of lattice reori-entation during deformation should also be different. This investigation was undertaken to test this idea. MATERIAL AND METHOD The remaining part of a single-crystal ingot of a 3 pct Si-Fe alloy,* prepared for an earlier investi- gation,1 was used in the present studies. Specimens 9/16 in. square and 0.365 in. thick were cut from this ingot with (001) planes parallel to the square surfaces, and the [loo] and 1010] directions parallel to the edges of the specimen, within ±1 deg. These machined crystals were etched to remove distorted metal, and annealed at 1300°C for 24 hr in a purified helium atmosphere. The annealed crystals had a hardness of 161 Dph. The crystal orientation was rechecked with X-ray back-reflection techniques. In high-strain rate experiments the crystal was compressed in a Dynapak machine to approximately 80 pct reduction in thickness (from 0.360 to 0.070 in. with an impact velocity of -500 ips). Thus, the duration of loading was approximately 6x 10-4 sec, and the average strain rate was about 103 sec-1. As a result of this rapid, severe deformation, the specimen became a roughly circular thin disc. The original shape of the crystal, however, could still be recognized by a diffusely outlined square area in the center of the disc. For compression at a low speed, the crystal was deformed in a universal testing machine at a rate of crosshead movement of 0.1 ipm. Compared with

Jan 1, 1965

By G. Sachs, S. I. Liu

INTRODUCTION IN a previous investigation on the effects of repeated strains of large magnitude on the aluminum alloy 24ST, it was found that the reduction in ductility by straining in tension was partially restored by a subsequent compression.&apos; As illustrated by the dashed line in, Fig I,§ the ductility (EF) retained after prestraining in tension by a certain amount (EI) and measured in a subsequent tension test is represented by a straight line sloping down under 45°. If a compression of the same magnitude as the first tension is inserted (E2 - EI) between prestraining and final testing in tension, such a "balanced" tension-compression cycle yields a ductility considerably higher than that present after prestraining in tension only. . The results of these tests can be correlated with those of an investigation on the effects of prestraining in compression.2 As also shown in Fig I, the ductility in subsequent tensile tests decreased with compression, at a rate considerably slower than that after prestraining in tension. The above discussed testing conditions can be considered as special cases of a general straining cycle, consisting of first, straining in tension by an amount E1, subsequently straining in compression by an amount E2, and finally determining the retained ductility, Ef, in a tensile test. Prestraining in tension is then represented by E1 > o and E2 = o. Prestraining in compression is given by E1 = o and e2 < o. Balanced cyclic straining is defined. by the condition E1 > o and E2 = -El. In order to obtain further information on the effects of straining cycles consisting of tension and subsequent compression, further tests were made, varying both the tension strain, E1, and the compression strain, E2, within extreme limits; El varied between 0.06 and 0.28 and E2 between -0.008 and -0.60 approximately. Apparently, such tests have not been previously performed. They revealed phenomena which have not been recognized to date. The results of the investigation are herewith reported, without attempting to correlate them with internal processes within the metal structure. However, in order to assist in an analysis of this type, the results have been represented in various manners. In addition, further test data on the effects of prestraining by compression were provided by using specimens of various contours (notched specimens) in the subsequent tensile tests.

Jan 1, 1948

By G. Krauss, W. Pitsch

The fine structure of the bcc martensite formed in an Fe-33 wt pct ATi single crystal of arrstenite is sho~on by transmission electron microscoPy to consist of combinations of transformation twins, stacking faults, deformation twins, and regular arrays of parallel screw dislocations. These structures constitute evidence for the multiple lattice-invariant deformations which operating during the formation of martensite could produce the real habit-plane scatter measured by a two-surface analysis of the plates formed in the single crystal of this investigation and reported in the literature for other Fe-Ni rnartensites. CRYSTALLOGRAPHIC theories1,2 of martensitic transformation show that the habit plane of martensite in a parent lattice is dependent in part upon an inhomogeneous distortion or lattice-invariant deformation which takes place on a fine scale within a martensite plate during its formation. Several recent theoretical papers3,4 have addressed themselves to an analysis of a wide variety of conceivable lat-tice-invarient deformations and the habit planes which they produce, while experimental investigation have been concerned with either the measurement of habit planes or the description and identification of the martensitic fine structure which reflects the nature of the lattice-invariant deformation operating during transformation. In Fe-Ni alloys with subzero Ms temperatures, the group of alloys with which this paper concerns itself, habit planes have often been found to scatter an amount greater than might be expected from possible experimental errors,5-7 and fine twinning has been identified as a major constituent of the fine structure of martensite.8-11 It has been suggested3,4 that more than one type of invariant shear occurs during martensitic transformation. This possibility has been experimentally supported12,13 by the observation of both dislocation configurations and twinning in a single martensite plate. The purpose of this paper is to report additional evidence for multiple lattice-invariant deformations in martensite and so to account for the real scatter in the habit planes of the martensite plates formed in Fe-Ni alloys. EXPERIMENTAL PROCEDURE The Fe-Ni single crystal was produced by pulling a high-purity iron and nickel charge through a single-crystal vacuum furnace in an alumina crucible. The crystal was double-melted to promote homogeneity and to increase its size by further additions on the second pass. In its final form the crystal was 4 cm in diam and 5 cm long. The nickel and carbon contents were analyzed at 32.9 and 0.006 wt pct, respectively. The austenite of this alloy first transformed to martensite by bursts at about -120°C, and, to preserve as much of the austenite as possible, all transformation was performed just below -120°C. Some observations were made on transformed samples which had been heated for 2 min at 340°C. It is assumed that the features of the martensite of these samples, Figs. 1 and 4, are the same as those of the as-quenched martensite. Orientation of the crystal by X-ray diffraction established 10.735 0.609 0.3161? as the axis of the crystal, an orientation that was checked within 2 deg by neutron diffraction. Further checks by electron diffraction of samples cut normal to the axis confirmed this orientation within the larger limits of error inherent in electron diffraction of thin foils. The X-ray orientation was the one used for the two-surface analysis of the martensite habit planes. A two-surface analysis was performed on the quadrant of the single crystal which had been oriented by both X-ray and neutron-diffraction techniques. Photomicrographs at X50 were made on two surfaces along an edge 2 cm long. Fiducial marks and the fact that many of the plates were almost completely surrounded by retained austenite made good matching of individual plates on two surfaces possible. The habit-plane trace on a surface was taken as the best line parallel to the long axis of a plate. A measure of the accuracy afforded by this criterion was provided by a family of very large plates which appeared at intervals along the entire 2 cm length of the edge. The plates all had habit-plane traces within 2 deg of one another. Many of the plates did not show midribs and, therefore, the use of midribs7 to represent habit-plane traces was not feasible in this investigation. The over-all experimental accuracy is estimated to be better than ±2 deg. Samples for transmission examination in a Siemens Elmiskop I at 100 kv were prepared by cutting 2-mm-thick discs from the single crystal, removing about 0.5 mm by chemical polishing,14 trans-

Jan 1, 1965

By Ernest Lilley

WHILE American scientific literature contains much information upon geologic conditions controlling the production of oil in Rumania, copper in Chile, and other fuel and metallic resources in many foreign countries, it is singularly lacking in data about the nonmetallics outside of the United States. Thus, though the United States is the outstanding market for European high-quality refined kaolin, and for the chinaware, porcelain, and other products of the European ceramics industries, Amer-ican literature contains only the briefest references to the deposits from which the raw kaolin utilized is obtained. To the writer, to whom has come in the past year .the opportunity of visiting a number of these deposits personally, they have proved of extreme interest both com-mercially and geologically. It is the latter phase that is discussed in this paper. The older and now largely crystalline rock areas of France, Germany, ;end other parts of western Europe contain numerous pegmatite dikes of which the upper portions have been subjected to surface weathering and kaolinization in much the same way as those of the eastern portion of the United States. Like the latter, the European pegmatite kaolins have long been known for their freedom from iron and other impurities offensive to the china and porcelain manufacturer. Unfortunately, they are also, like the American deposits, individually of small size and noted for their high costs of production. Deposits of sedimentary clay similar in many respects to the high-quality sedimentary kaolins of Georgia and South Carolina are known and worked, notably in southern Germany and in the Newton Abbott district of Devon and Dorset. in England. In general, their relationship to the parent rock from which they were derived is more evident than in the United States and the individual deposits are of smaller areal extent and less regular in outline.

Jan 1, 1932

By L. W. McKeehan

IT is no longer necessary, if it ever was, for your annual lecturer to apologize for including in his remarks frequent references to the arrange-ment of metal atoms in crystals and for basing his arguments that metals behave as they do upon their crystal structure. Neither will any objec-tion be raised because the large metallic crystals of which we will speak are hard to prepare and of negligible commercial interest. The particular set of physical properties we propose to discuss-ferromagnetic proper-ties-may require more justification. Very few in this audience are primarily, or even remotely, interested in the ferromagnetic behavior of the metals they handle. By no means all of you ever deal, by choice or by necessity, with metals which display any ferromagnetism at all, and even those who study or control ferrous metallurgy must usually depend upon electrical engineers for assistance in ferromagnetic applications. My excuse for talking about such an obvious specialty is, like all Gaul, divided into three parts. In the first place, the members of the com-mittee who select the annual lecturer must wish the speaker to confine himself to matters he has at least thought about before he prepares his speech. In the second place, the study of ferromagnetism in crystals has, as you will soon realize, suffered in the not-too-distant past from inade-quate metallurgy. Further progress probably depends upon proper use being made of the skill and knowledge of some members of the Institute of Metals Division who have not, before today, been asked to think about the problems presented here. Finally, there is at least a sporting chance that the ferromagnetic properties of a few metal crystals will give some insight into the more generally interesting properties which they share with nonferromagnetic metal crystals.

Jan 1, 1934

By G. R. Love, C. C. Koch

The changes in superconducting properties with aging time have been studied ,for the pecipitation reaction in a Tc-30 at. pct V alloy. Superconducting critical temperature, upper critical field, and relative critical current density were determined by ac susceptibility techniques. Aging produces changes in critical temperature of both matrix and precipitate which can be rationalized by compositional effects. maximum flux pinning (critical current density) occurs at a time during aging when subgrain boundaries are completely decorated with precipitates and the subgrain centers remain precipitate -free. The particular effectiveness as barriers to flux motion of planar defects which enclose regions of low deject density is discussed. THE precipitation of a second phase can dramatically modify the superconducting properties of type I1 super-conductors. According to Livingston and Schadler1 one might expect changes in the primary, secondary, and tertiary superconducting properties of the material. Changes in matrix chemistry caused by precipitation can alter the fundamental superconducting parameters; critical temperature, Tc, and thermody-namic critical field, Hc. The concimitant changes in electron mean free path (reflected in normal state resistivity) can affect the critical fields Hc 1, IIc2, Hc3. Finally, the presence of precipitate particles may hinder the motion of flux lines and may considerably improve the current-carrying capacity in high-field superconductors. The influence of precipitation on superconducting properties has been studied in a number of systems.2 Magnetization measurements have been used to study the influence of precipitates on flux pinning in lead-base alloys by Livingston3 and Evetts et al4 In these alloys precipitates induced magnetic hysteresis and flux trapping. The amount of hysteresis increased with the volume fraction of precipitate and decreased with coarsening of the precipitate. Jn an Al-Zn alloy5 and an A1-Ag alloy6 the initial precipitate size was presumably smaller than a coherence length and coarsening increased magnetic hysteresis5 and critical current density.6 The influence of precipitation on superconducting properties has also been studied in several of the commercially interesting Ti-Nb7-10 and zr-Nb11 alloys. The maximum in critical current density for these alloys was confined to a narrow range of either isothermal aging time" or isochronal aging temperature7 during the precipitation reaction. Thus, experimental evidence and theoretical considerations suggest there is an optimum precipitate size, spacing, and density, and a critical composition with respect to the matrix for flux pinning. What these "optimum" values might be and the relative importance of each is still not clear, although a few generalizations can be made. It is generally accepted1&apos; that particle sizes smaller than the coherence length or larger than the inter-flux line spacing are poor pinning centers. In high Hc2 materials, precipitate sizes for maximum values of critical current density lie in the range of 50 to 2000Å,9,7 and there are indications that increasing dissimilarity between precipitate and matrix produces increasing pinning force.13 Because of several interesting features of the aging reaction in a Tc-30 pct V alloy, we have chosen to study the influence of precipitation on the superconducting properties of this alloy. The physical metallurgy14 and a survey of the superconducting properties" of the Tc-V alloy system have been reported. The Tc-V phase diagram is presented in Fig. 1. At 1500°C the Tc-30 pct V alloy is in the single phase 6 field. Samples quenched from the 6-phase field have a CsCl structure X-ray diffraction pattern at room temperature and it has been proposed that the 6 structure is closely related to the bcc lattice.14 When held isothermally below the eutectoid temperature, 115O°C, the 6 phase decomposes into the CsCl and hcp phases.

Jan 1, 1970

By Earl S. Bardwell

The determination of suitable and safe annealing temperatures is one of the most important problems arising in the operation of a copper rolling mill. Certain of the larger mills have worked this problem out for themselves and in these mills the operation has become more or less standardized. In some of the mills pyrometers are used to measure the temperature of the annealing furnaces and careful watch is kept to see that overheating does not take place. In a considerable number of the mills, however, dependence is placed entirely on the judgment of the operator. The almost total lack of literature bearing on this subject seems sufficient warrant for the publication of this paper. &apos; The discussion of this subject naturally divides itself into two parts: (1) The effect of annealing temperature on physical properties; and (2) changes in the microstructure of refined copper due to cold rolling and annealing. I. The Effect of Annealing Temperature on Physical Properties For the purpose of investigating this phase of the subject six test bars were selected, varying in oxygen content between the limits of 0.036 and 0.070 per cent. The chemical composition of each of these test bars was as follows: Bar Number 1 2 3 4 5 6 Copper + silver...... 99.95 99.92 99.945 99.94 99.95 99.93 Oxygen.............. 0.041 0.070 0.046 0.050 0.036 0.058 As + Sb............. 0.0038 0.0038 0.0038 0.0038 0.0031 0.0031 The bars were heated in an electric muffle to about 1,650" F. and rolled into rods. The rods were annealed, pickled, and drawn to No. 12 B. & S. gauge wire. The wire which was to be used for the annealing test was cut into 38-in. lengths and each length made into a coil 6 in. in diameter. The separate coils were marked so that they might readily be identified

Jan 1, 1915

By R. W. Nash, A. E. Schwaneke, V. R. Miller

The Bureau of Mines developed a detector for controlling sorting devices to separate the copper-bearing fragments from the barren portion of Michigan native copper and western prophyry copper ores. A successful sorter could be used to preconcentrate the ore and eliminate costly hoisting or hauling of waste. An induction balance unit was developed and used in sorting tests on crushed sized - 2.5 + 1.3-cm (- 1 + 112- in.) ores from the Kingston (0.9% Cu) and Centennial (1.6% Cu) mines of Upper Michigan. Concentrates of 4.0% and 7.5% Cu, respectively, were obtained at recoveries of 85 and 80% of the copper in the feed. Eighty percent of the sorted ore was rejected as tailing. Sorting larger fragments improved the separation efficiency. Tests on - 10+ 5-cm (- 4 +2-in.) sized Kingston (1.6% Cu) and Centennial (2.1 % Cu) ore samples yielded concentrates of 4.3 and 4.5% Cu, respectively, with corresponding recoveries of 92 and 91 %. A bout 60% of the sorted ore was discarded as tailing. Porphyry copper sulfide ores also responded to electronic sorting but at a lower separation efficiency. Sorting response was affected by the degree of segregation.

Jan 1, 1979

By G. Y. Chin, M. T. Dolan, W. L. Mammel

In the case of plastic deformation by slip, von Mises&apos; showed that an arbitrary shape change of a crystal generally requires the activation of five independent slip systems. The selection of the five active systems was worked out by Taylor ,&apos; who hypothesized that, among all combinations of equivalent slip systems which are capable of accommodating a given imposed strain, the active combination is that one for which the sum of the absolute values of the glide shears is a minimum. Taylor analyzed the case of {lll}( 110) slip for fcc metals and applied the analysis to crystals undergoing axisymmetric flow, which approximates the shape change of an embedded grain in a polycrystalline aggregate deformed in tension (or compression). For the twelve equivalent (111) (110) slip systems, there are 384 independent combinations of five slip systems that satisfy the imposed strain.&apos; Taylor laboriously calculated the value of M = ZjIyj /E for each combination (although some were missed) and obtained the minimum M, hence the active combination, for a number of axial orientations distributed throughout the stereographic triangle. (yj is shear from slip on the th system and e is the tensile strain). Detailed contours of constant minimum M were recently obtained by Hosford and Backofen using a simplified but equivalent Bishop and ill&apos; analysis. Due to the numerous combinations of slip systems involved in the calculations, however, the full potential of the powerful Taylor analysis has not been exploited. For this reason, we have recently utilized techniques of linear programming to obtain solutions of the Taylor analysis for axisymmetric flow, for slip on {110)(< 111), {112)(111), and {123)(111) systems as well as mixed slip composed of these three systems. These slip modes are of obvious importance in the deformation of bcc crystals. Some of the salient results are summarized below. 1) Stress-Strain Data for Polycrystal. The value of M averaged over all axial orientations is the ratio of the tensile flow strength of a randomly oriented aggregate to the critical resolved shear stress for slip. This value enters importantly in theoretical deductions of the polycrystalline stress-strain curve from single-crystal data.2&apos;3&apos;5 Table I lists the values of Ma,, for the several cases of slip, as obtained by the present computer work. 2) Texture Hardening. Since the value of M depends on the axial orientation, the (tensile) flow strength of a specimen may be increased through texture control.&apos; An example of the computer results is shown in Fig. 1, where contours of minimum M have been computer-plotted for the case of mixed slip on {110}(111), {112)(111),and {123}(11 1) systems. It may be seen that, under axisymmetric flow, wires of (111) and (110) axial orientations are 50 pct stronger than those oriented at (100) .

Jan 1, 1968

By D. J. Carney, C. W. Boquist, E. C. Rudolphy

Effect of variations in sinter feed composition on sinter strength, bulk density, re-ducibility, chemical composition, and microstructure were determined by sintering experimental samples on a production sintering machine. Increasing amounts of roll scale, ore fines, return fines, and blast furnace slag were most beneficial to feed permeability, sinter bulk density, and strength. Burnt lime additions improved feed permeability but were not beneficial to sinter strength or bulk density. Sinter reducibility was adversely affected by all additives. DEVELOPMENT of methods for evaluating sinter quality, which would in some way predict the behavior of the sinter during charging and smelting in the blast furnace, has been given considerable attention in recent years. In a previous investigation at South Works of the United States Steel Corp., standard sinter sampling and testing procedures were developed.1,2 By modifying the sinter sampling device, a method of sintering experimental mix sinter samples upon a production Dwight-Lloyd sintering machine was also developed. This technique afforded a rapid and controlled method of investigating the effects of the various raw materials and additives on sinter quality and was used in this present investigation. Since the beginning of the present study in 1953, the results of numerous sinter investigations have been published, most of which were concerned with production tests of iron ore sinter, both here and abroad. Three groups of investigators reported results of experimental sinter studies that were related to this investigation. Voice et al.3 studied the effects of controlled variables on sinter quality by producing and testing experimental Northants iron ore sinter using an experimental sintering unit. Mor-rissey and Powers&apos; determined the relationship between iron ore sinter quality and the moisture and coke content using a small laboratory sintering system. Burlingame et al.5 studied the effects of "additives" upon iron ore sinter using a laboratory sintering apparatus and laboratory grade raw materials. At South Works, it was considered desirable to study the effects of sinter mix composition and additives upon the quality of a flue dust-base sinter produced on a production sintering unit. Extrapolation of controlled laboratory test data to sintering plant operation lacking such precise control is not altogether satisfactory. Therefore, the present study was conducted in a manner which approximated production conditions as closely as possible. The raw materials used were those commonly encoun- tered in the production of flue dust and flue dust ore-type sinters and these were varied within extremes encountered in this type of sinter production. Experimental Procedure The experimental sinters were produced from 100 lb mixtures of sinter feed. The principal raw materials and additives used, their particle size, and approximate chemical composition are listed in Table I. The mixing of the raw materials was accomplished by means of a miniature single shaft pug mill shown in Fig, 1. The use of the pug mill as a mixer was decidea upon after encountering difficulty in reproducing the mixing and chopping effect of the sinter plant pug mill with other types of available small mixers. The miniature pug mill was constructed, consisting of 31/2x2x1/4 in, blades spaced 3 in. apart along a 3 ft shaft. Preliminary tests were run with this small mixer to establish the proper rotation speed and the required number of passes through the pug mill to thoroughly mix and distribute all the raw materials in a manner approximating the production Pug mill- Although the effects of varying the mosture content were determined in one particular series of tests, the amount of moisture added was changed as the composition of the experimental mix was varied. The aim in making water additions was to achieve a permeability as high as possible for each particular

Jan 1, 1956

Closed-circuit television was first installed under- ground by United States Steel&apos;s Tenessee Coal & Iron Division during the summer of 1957. Placed at a rotary dump location in one of TCI&apos;s mines, the installation was designed to permit operation of all functions of the load car haul chain, rotary dump, and empty car haul chain from a remote location, and to improve safety. The initial installation was very successful, and similar ones were subsequently placed at all of TCI&apos;s operating ore mines. The 10-ton capacity, automatic coupled mine cars are placed on the load car haul chain by the main-line locomotives. The haulage dispatcher has been located at the skip loading point of the underground pocket, some 80 to 100 ft below the rotary dump. The video monitor is located so the operator has a constant view of the activities around the rotary dump. By means of remote controls, the TV camera can range through a four-way turret of lens changes, can pan 350° in about nine seconds, can tilt 45° up or 45° down in nine seconds, and also can range through an optical focus for any of the lens positions.

Jan 3, 1961

By Alistair Frame

INTRODUCTION In April 1988 discussions were about to start with BP on the possibility of buying their- mineral interests, and it took a long time to arrange a deal. I will talk about RTZ without BP Minerals, look at the new RTZ with BP Minerals, discuss the outlook for metal prices, and review the problems in South Africa and develop the case against sanctions on that country. RTZAT THE END OF 1988 Late in 1987, after completing a worldwide review of our strategic thrust, we decided: 1. That the business focus would be to remain a major diversified natural resource group with interests in related industries. 2. To divest non-core and low growth businesses. 3. To develop a logical acquisition plan. 4. To emphasise organic growth and, most importantly, to enhance shareholders&apos; wealth by capital increase and a progressive dividend policy. Subsequently, we concluded that we should sell our oil and gas business and dispose of several assets for which we saw little growth potential. The disposal programme raised some U.S.$ 1,600 million, representing a significant capital gain on our various investments. All transactions were carried out by our small Head Office staff in London, without the help of merchant banks and lawyers, and we were able to safeguard the employment of our staff in all these operations. The most interesting disposal was of our oil and gas interests. Before the 1987 strategic review, we had ambitions to develop our oil and gas interests and to become the leader in the second division of European oil companies. Our interests, which were purely in exploration and production of oil and gas, consisted of the 100% owned RTZ Oil and Gas company, and 29% of LASMO, a publicly quoted U.K. oil and gas company with extensive worldwide interests. LASMO, in turn, owned 25% of Enterprise Oil, one of the more successful of the North Sea oil exploration and production companies. Prior to the end of 1987, our intention was to acquire control of both LASMO and Enterprise. However, when we evaluated the net asset value of these two companies based on our oil price assumptions, which were pessimistic for the next five years or so, we concluded that they were both trading in the market at significant premiums. This, taken with the additional premium required for acquisition and the high cost of exploration, led us to conclude that, since funds could undoubtedly be used to better effect, we should sell our interests. Turning to the other major achievements in 1988, we commissioned, and built up to design levels in a very short period of time, the Morro do Ouro gold mine in Brazil. This mine reached its design output of 100,000 ounces of gold per year within three months of start-up, which was on time and under budget. We are now considering a possible expansion of this property. In South America, Utah International, Mitsubishi and RTZ arranged non-recourse finance, with post completion guarantees, for the giant Escondida Project in Northern Chile. Financing came from a group of banks in Japan, Germany and Finland -- the countries to which most of the concentrates will be sold -- and from the LEC. The average output of the mine for the

Jan 1, 1990