Search Documents

By J. Hudy

An investigation has been made to determine the applicability of the Cendrex X-ray instrument for the measurement of the ash contents of washed bituminous coal products. The results obtained for selected products from five preparation plants in the northern Appalachian region are described. Emphasis of the study was placed on low-ash bituminous coals suit-able for utility or metallurgical markets. There was good agreement between the results obtained by conventional ash determination methods and by the Cendrex for all the products tested. A principal disadvantage of coal in competition with other fuels has been its inconsistent quality, especially with respect to ash content. Mine rnechanization and production from coalbeds of inferior quality have accentuated this failing. Present quality control methods in coal preparation plants are inadequate because (1) control samples taken over a production shift only serve to give the average quality of the product, (2) conventional sampling and analysis data are usually not available at the time a shipment is scheduled, and (3) the plant operator does not have the use of such data when the coal is being processed so that operating conditions may be adjusted for correcting variations in quality. Thus, the development and use of continuous-control monitoring instruments is of prime importance. The Federal Bureau of Mines arranged to investigate an instrument using x-rays for rapid continuous ash determinations. Developed by the Dutch State Mines and first described in 1958,' this instrument, which has found widespread acceptance in Europe, is designed to provide ash analysis of any desired coal feed or product stream with only a five-minute time lag between sample collection and analytical results. With limit controls, this unit could be used to feed back signals to preset the separating gravity of coal washers, control the ratio of various coals needed to produce an acceptable blend, and permit the sorting of a washed product into two qualities, one which is below and the other which is above a prescribed ash content. This unit can also be used discontinuously for rapid determination of coal samples taken in the usual manner. THEORY Di jkstra and Sieswerda of the Dutch State Mines studied the effect of chemical composition and ash content on the absorption coefficient of coal with the transmitted radiation method.' They found that with an X-ray wavelength of 1.79 A and values calculated for the absorption coefficients of ash and combustibles, the absorption coefficient of coal gave a linear relationship when plotted against the ash content. Thus, a method of measuring the absorption coefficient of coal could also be used to measure the ash content. However, practical attempts to measure the ash content of coal by comparing the intensities of the transmitted X-rays failed. The absorption coefficient of coal can also be obtained by irradiating a layer of coal with x-rays and measuring the intensity of the diffused reflection (backscatter method). The relationship between the diffused reflection and the ash content is actually hyperbolic but approximates a straight line over a narrow range. A measuring circuit that balanced the difference in intensity of the reflected radiation from a standard surface against that from a coal sample was used. By plotting this difference of reflected radiation against the ash content, a curve which approximated a straight line over a range of 8 percentage points of ash was obtained. DESCRIPTION OF EQUIPMENT The apparatus performs two distinct functions: (1) the preparation of the sample to a suitable size consist and moisture content for delivery to the x-ray element, and (2) the measurement of the ash content by the x-ray element. In a continuous operation the coal sample is delivered to a conditioner where it is dried to a maximum of 1% surface moisture and pulverized in a high speed mill to -48-mesh. This material is fed, at a rate of 250-300 gpm onto a rotating disk, shown in Fig. 1, where it is mixed with material already present. The mixture is rotated on the disk and

Jan 1, 1969

By R. J. Murphy, N. J. Grant, J. W. Dowding

A large number of blast furnace slag-metal tests were examined to determine if the manganese reduction could be used as a primary indicator of the degree of oxidation or reduction of the slag and of its desulphurizing power. Slag basicity and temperature were also evaluated. Two laboratory heats were made and sampled prior to reaching equilibrium to check blast furnace data. IN a recent investigation of the factors affecting desulphurization in the blast furnace, is was evident that manganese reduction appeared to parallel the course of desulphurization. Grant, Kalling, and Chipman1 pointed this out in a series of time studies utilizing closely controlled laboratory melts. Fig. 1 is a composite plot of sulphur removal and manganese reduction as a function of time under two slags of different basicity. Manganese reduction appears to approach equilibrium at approximately the same rate as does sulphur. It was also demonstrated that the addition of oxygen to the slag, as manganese oxide, caused a sharp reversal of sulphur from the slag to the metal.' It has been shown that "Excess CaO" was a primary factor in measuring the degree of desulphurization under ideal reducing conditions,1,2 the following reaction being representative of the process: CaO (slag) + S + C (solid) = CaS(slag) + CO (gas) It was also evident that a second reaction could drive the sulphur from the slag into the metal. A suggested reaction was' CaS (slag) + 0 = CaO (slag) + S Any change in the oxidizing power of the system would thus affect both the sulphur and the manganese without causing any change in the calculated basicity of the slag. "Excess CaO," "Excess Base," and other similar basicity values, under such oxidizing conditions, would therefore not be the best measure of desulphurizing power; instead, as was shown by and Chipman" he oxygen content of the slag at low oxygen levels would be the controlling factor. Unfortunately, the extent to which FeO is reduced in the blast furnace makes it difficult to utilize slag FeO as an accurate indicator of the degree of oxidation. By comparison, manganese reduction in the blast furnace proceeds more slowly and is generally only about 40 to 70 pct complete. manganese, which is present in significant amounts and is readily analyzed, offers an opportun-

Jan 1, 1954

By N. A. Gokcen, S. Fujishiro

THE pressures of Mn(g) in equilibrium with Mn7C3 and graphite have been measured by McCabe and Hudson' and Butler, McCabe, and paxton2 by means of graphite, zirconia, and Ta-Mo Knudsen cells. The details of corrections in their measurements were somewhat different from those of the authors;3'4 hence, further independent results at higher temperatures seemed to be warranted. The stoichiom-etry of Mn7C3 in equilibrium with graphite and its stability up to the vicinity of 1373 °K have been satisfactorily established by Kuo and persson5 (See also Hansen and Anderko).' The method of investigation has been described elsewhere in detail.3'4 The carbide was prepared in the manner described by McCabe and Hudson. In order to avoid possible reactions with refractory oxides, only graphite cells were used for the effusion experiments. The authors' results are the runs M-1, M-2 and M-3 listed in Table I, together with those of McCabe and co-workers. The heat capacity, c;, of Mn7C3 is not known; therefore McCable et al. plotted their data as log P vs 1/T and the results were only expressed first' as, and later2 as logP=- -14220+6.06 without further thermodynamic calculations. However, it is possible to estimate closely the necessary heat capacity as follows: When H; - &98 of CrC, or MnO, is plotted vs x, corresponding to various compounds, with temperature as the parameter, it is seen that the relationship is represented by a line of very small curvature. This relationship is also followed by other compounds which do not exhibit solid state phase transformations. In view of the fact that chromium and manganese have the atomic numbers of 24 and 25 respectively, it is reasonable to assume that H; - H;ae vs x for MnC, follows the same type of lines as those for CrC, for which adequate data are available.7 Similar correlations appear to be valid for oxides of two neighboring metals for which reliable data are available. The procedure is thus to move the lines for CrC, vertically (parallel to the axis of HT - H298) until they coincide with the points for MnC1/3, the only carbide of manganese whose H; - HO298 has been

Jan 1, 1963

By John R. Gould

A mathematical treatment of multiple-pass floating-zone refining of semiconductors, including the evaporation of solutes from the melt at reduced pressure, is presented. Vapor pressures and evaporation rate constants for phosphorus, arsenic, and antimony in germanium have been determined from floating-zone experiments conducted at 10 mm Hg. Rate sensi-tivity of arsenic in germanium has been examined over the range of 1 to 10 in. per hr growth rate. The equilibrium value of the segregation coefficient of arsenic in germanium, as determined by an extrapolation of these data, was found to be 0.09. PFANN has treated the segregation of nonvolatile solutes in the zone-melting process, Bradshaw and Mlavsky2 considered the evaporation of solutes in a vacuum during the growth of crystals by pulling from the melt, and van den Boomgaard3 has shown that it is possible to bring a volatile impurity element homogeneously into an ingot by means of zone-melting under a constant pressure of that element. This paper is concerned with the volatilization of solutes during zone - melting in a vacuum. The mathematical analysis by Lord4 of multiple-pass zone melting is extended to include evaporation of solutes. A method is presented in which evaluations of vapor pressures, evaporation rate constants, and distribution coefficients may be derived from the variation of solute concentration in the floating-zone refining of germanium at 105 mm Hg. EXPERIMENTAL Ingots of zone refined germanium, approximately 1/4 in. in diam and 10 to 12 in. in length, were subjected to several floating-zone passes at 105 mm Hg in order to provide intrinsic material for these studies. These ingots were then seeded in a [Ill] direction and solid-doped to a constant impurity concentration of approximately 1015 atoms per cmS in a forming gas ambient (10 pct H - 90 pct A) at 1/2 atm gage. The resulting crystals were subjected to repeated floating-zone passes at 105 mm Hg and a concentration profile along the length made after termination of each pass. Concentrations were determined from four-point probe resistivity measurements, and proper precautions were taken to prevent contamination during handling. A constant zone length, crystal cross section, and growth rate were maintained during zoning. A stationary coil and moving crystal system were employed for floating-zone growth with neither the section of crystal above nor below the melt rotated.

Jan 1, 1962

By David White

THE search for potash salts in the great "Red Beds? region of the Southwest, conducted for several years by the U. S. Geological Survey, the work being carried on for a part of the time in coöperation with the Bureau of Economic Geology and Technology of the University of Texas, has resulted in the discovery, within shafting depth, of potash salts, apparently of workable thickness and commercial quality, and prob-ably of great extent. Definite information is lacking as to the exact thickness of the potash beds, the size and boundaries of the areas underlain by workable strata, and the locations of the deposits richest and most favorably situated for exploitation. Briefly to review the salient features, of the general situation: We have in the great Red Beds region of the southwestern United States, embracing portions of central Kansas, western Oklahoma, eastern New Mexico, and northern and western Texas, .a series of sandstones. shales, anhydrite beds, clays and limestones, which; through an interval of 1000 ft., more or less, carry beds of salt, estimated by Darton1 to contain over 30,000 billions of tons of rock salt. It is the greatest known salt field of the world. At some points the intercalated beds of rock salt, one of which is reported by the driller to exceed 300 ft. in thickness, aggregate, accord-ing to the drillers' records, over 1000 ft. The sedi-mentary strata are similar in composition to those carrying the potash deposits of western Europe, and they were laid down at the same time and under condi-tions which, in many respects at least, were similar The stratigraphy and character of the beds are des-cribed by Darton2 and a, part of the area and the reported aggregate thicknesses of salt are shown, with some revision after Darton, in the accompanying map Fig. 1. The assumption that in the great areas of shallow evaporation basins spread over -the vast base-level region of saline deposition in the Southwest during Permo-Triassic time, potash salts were in some places, and at different stages, thrown down in crystalline deposits associated with the beds of rock salt, anhydrite, and gypsum, is, geologically speaking, more than reason-able. They are to be expected, and the conviction that they are probably present has long been held both in the Texas Bureau of Economic Geology and Tech-nology, under Dr. J. A. Udden, and in the- U. S. Geological Survey. Accordingly, for many years, efforts to determine whether potash deposits are present in this region have been made, though under very great difficulties, such as insufficient funds for boring, hack of drilling on private initiative in the more promising regions, hack of interest at first on the part of the drillers and companies, and, hater, inadequacy both of the methods of boring and of the sampling, to reveal in definite terms the thickness-of any saline stratum of given composition.

Jan 4, 1922

By Frank Marotta, Louis B. Lesem, Frank Greytok, John J. McKetta

Although one of the primary variables in the calculation of the flowing bottom-hole pressure in gas wells from surface measurements is the temperature at any point and its distribution in the flow-string, only few experimental data are available in the literature and little attention has been given to analysis of the problem. Virtually all of the recently published methods of calculating flowing bottom-hole pressures depend on the assumption that either the temperature is constant at some average value or that the variation is linear with depth. The purposes of this work are to analyze the problem theoretically and to verify the analysis by comparison with experimental data so that practical problems in the analysis of the behavior of gas wells can be solved with greater accuracy, reliability, and ease. MATHEMATICAL OUTLINE OF PROBLEM Assuming that: 1. The mass velocity and chemical composition of the gas stream are constant and in normal gas well operations, the change in linear velocity in the entire flow-string is trivial, 2. The product of the density and heat capacity of the gas is constant, 3. No horizontal temperature gradient exists in the gas stream, 4. Net flow of heat by conduction within the formation and in the gas stream in the vertical direction is trivial in magnitude and can be neglected, 5. The regional vertical geothermal gradient is constant, and 6. The temperature of the gas entering the borehole is constant, and equal to that of the reservoir, a set of two simultaneous, linear partial differential equations with appropriate boundary conditions was derived to describe the temperature distribution in the gas stream and the surrounding formation. These equations were solved by operational techniques for the distribution of temperature in the gas stream. The resulting integrals were evaluated numerically on an IBM 604 at the Machine Accounting Div. of the Railroad Commission of Texas. DERIVATION OF FUNCTIONS FOR THE DISTRIBUTION OF TEMPERATURE The physical system is a circular hole of radius a in an infinite medium with thermal conductivity K, density p8, and heat capacity c,. Under shut-in conditions the well is in thermal equilibrium with the surroundings and the increment in temperature is given by - ?T3/L x. Gas of density pg and heat capacity c.. flows upwardly through this hole in the direction of increasing x with a linear velocity W. Writing a heat balance on an element of gas ?x in thickness, convective heat transfer + conductive heat transfer + energy required to lift a unit mass of fluid = change in energy content. pa2W po Co To - pa2Wpo Co To x+xx - 2apK?x ?T8/?r r=a - Wpa2 po?x/778 = CoPopa2?x?To/?t... Dividing by (copopa2?x) and taking the limit as ?x tends to zero, -W (?To/?x + 1/778Co) + 2 K/a Po Co ?T3/?r r=u = ?To/?t

Jan 1, 1958

By Michael A. Zappia

INTRODUCTION The San Manuel mine of Magmacopper Company is located approximately 72 km northeast of Tucson, Arizona. The mine, concentrator, smelter, electrolytic refinery and continuous rod casting are located on the west side of the San Pedro River valley. Ore Production: 58 1W mtpd Production To Date: Over 340 000 000 mt since 1956. Ore Grade: 0.70% net sulfide cu. As conceived at the present time, the San Manuel ore body is the lower half of what was originally an elliptical (In cross sect ion) cylinder same 2400 m long with major and minor cross sectional axes of 1500 m and 760 m. After emplacement, the cylinder was diagonally sliced along its long dimension by the San Manuel fault, which separated it into halves, moving the upper half same 2500 m down dip and bringing a wedge-shaped blanket of tertiary conglomerate into position over the lower segment of the cylinder. The lower segment is the San Manuel ore body. The upper part, moved down dip, is the Kalamazoo ore body. Originally, these were one ore body. The San Manuel ore body is a structurally weak and highly fractured quartz monzonite, the principal ore minerals being chalcopyrite, with small amounts of molybdenite. The present mining method is full gravity diagonal retreat panel caving by block. This is shown on Figure 2 , (Block Sequence 56, 57, 58, 59 --on the following page.) The ore mined is hoisted to the surface for transportation to the concentrator. BLOCK CAVING MINING SEQUENCE HISTORY The San Manuel mine was planned and developed as a full gravity block caving mine. It continues as a full gravity block caving mine. Since its initial start, the major changes in mining have been in the areas of ground support, rate of draw and undercut sequence. Ground weight resulting from block caving plays a dual role. It can cause extensive damage to ex- traction openings, yet it is necessary to break the ore into easily handled size. The ground- weight problem resolves itself into finding ways to make it manageable. The initial early ground support in the production areas consisted of timber sets and various combinations of steel and timber sets. This sup- port system proved unsatisfactory and a new support system utilizing concrete was developed. Concrete support, 30 cm to 45 cm thick, proved satisfactory. Rates of draw were experimented with. A draw rate of 45 cm to 61 cm (32 to 45 mt) per draw point per day was determined as optimum in con- trolling ground weight. Undercut sequence or mining sequence was recognized as a major contributing factor to ground weight. This is the most difficult factor to change. The lead time from primary development to undercut can be as much as two years. Initial Checkerboard Pattern The initial undercut sequence was in a checker- board pattern (Figure 2). Blocks Sequence 1, 2, 3, 4, 5, 6--next page.

Jan 1, 1981

By R. W. Raymond

This name is applied to the present mining law, as enacted in 1872 and since, to indicate its leading characteristic—in which it differs from all previous mining laws of this or any other country. The earlier act, passed in 1866, was practically the first attempt of Congress to deal with the question of mining titles upon the public domain. It was framed after nearly twenty years of acquiescence on the part of the Government in the self-constituted tribunals, officials, rules, and customs of the mining districts. In its recognition of these, and in several other particulars, the act of 1866 was open to serious criticisms. It is the purpose of this paper, not to trace the history of legislation on this subject, or show in detail what were the faults of the earlier law, but rather, by a discussion of certain aspects of the present law, to point out how great a revoluition it has effected in the rights of mining locators, and to indicate some of the difficulties attending its application. In the attempt to correct the vagueness of the act of 1866 an entirely new elernent was introduced into the law, bringing with it a new set of difficulties. Under the act of 1866 and the miners' customs which it followed, the lode was the thing claimed and subsequently acquired by patent. And the claim to a given number of feet on the longitudinal course of the lode was rooted in 'a discovery of any part of the lode in any part of the claim. ("Extensions" could in many districts—perhaps universally—be located and claimed on the strength of the discovery in the principal claim to which they referred; but this is a point not essential to the present discussion.) It was not necessary to find the outcrop or the upper edge of a lode in order to lay a valid location upon it. An explorer, sinking a shaft and intersecting a lode not already discovered and claimed by another, could claim by that discovery the number of feet along that lode which the local laws might permit (not exceeding the maximum set by the United States statute) whether his sur-

Jan 1, 1884

By Frederick F. Sharpless

The term "segregation," as here used, means the separation of certain natural resources into groups, consisting of one or more members, with the idea that when thus segregated, each group may be more easily and effectively administrated. We may, for example, consider surface rights as distinct from underground rights, and stop there; or we may go further, and deal separately with timber, water, and agricultural rights, or, going underground, we might deal separately with such groups as precious and base metals, clay, oil, gas, etc. The present paper contemplates only the separation so far as practicable, for administrative purposes, of surface from mineral rights. " Classification," in this paper, has reference to the groups into which the government has divided, is dividing, or will hereafter divide its natural resources; first, into the broad classes of mineral and agricultural lands; and, second, into coal, oil, phosphate, brine lands, etc., the central idea being the separation into natural groups for the purpose of simplifying administration and for the purpose of encouraging maximum development and minimum waste. The two subjects are in some respects quite distinct, but as my argument develops, I think it will be obvious why they are discussed in the same paper. In the pursuit of our professions as mining engineers, geologists, or operators, we are continually confronted by conditions with which our present mining laws or regulations are incompatible. It may be a conflict, hardship or injustice, a piece of favoritism, or of unnecessary red tape; or we may see lack of development in a promising locality, and wonder what is the reason. Often we can see where a modification, slight or radical, in the laws would have obviated the difficulty without doing harm to any of those immediately concerned. Such alterations as individuals could intelligently suggest would be based on a relatively small number of situations occurring in their experiences. The published replies to the queries formulated by the various committees on mining law appear generally to reflect personal experience. Concerning a few points, there is a marked uniforhity of opinion, while on other points opinions

Jan 1, 1915

By R. H. Richards

The spitzlutte, as described by Rittinger, is an instrument by which saud is sorted in a continual upward-flowing stream of water. Its usual firm is that of a pointed box, placed with the point downward, the box receiving. its feed of sand and water on one side and discharging its tailings on the other. The sorted product or concentration is discharged at the bottom, at the apex of the box, through which it falls against an upward current of water, which current serves to effect the sorting and separation. To make this exposure to the quicksand condition still more effective, an inverted dam is placed across the spitzlutte, which forces the sand in its passage from the feed side to the discharge to pass clown into the more active portion of the upward-flowing current of water. In the form adopted for small tests in the mining laboratory of the Massachusetts Institute of Technology (see accompaaying sketch) the feed is'throogh a central funnel instead of being at the side, and the apex of this funnel, extending down nearly to the apex of the cone, talks the place of the inverted dam in the large spitzlutte. To keep the experiment perfectly under control a bulb or bottle is attached by a rubber connecting-tube to receive the concentrations, and between this bottle and the apex of the spitzlutte is placed a glass tube of conical form, with a side tube for' the admission of water. By regulating the admission of water through this tube the concentration may be allowed to go down into the bulb as fast or as slowly as the richness of the ore seem.; to demand. This spitzlutte may be used on products that have been previously sized to take out the heavy mineral. As an example of this a test was made upon a sample of ore where the galena, blende, and quartz were much mixed up, but separated fairly when crushed. The sample of ore was from Newburyport, and assayed 16.61) per cent. lead.. After sizing through a series of sieves the ore yielded conceutrations and tailings to the spitzlutte as follows :

Jan 1, 1881

IlAbad, Leopoldo F , Min Engr , Div of Mines, Bureau of Science, Manda, P I '23 ||Abadilla, Quince, A , Cia Minera de Petrolco El Aguila, S A Box 86, Puerto Mexico, Ver , Mexico '20 ||Abarquez, Ramon F , Met , Bureau of Science Manila, P I '24 ||Abbey, Robert Graham, Student, Case School of Applied Science Cleveland, Ohio '21 Abbott, A N , Mines Supt, Mazapil Copper Co , Ltd Concepcion del Oro, Zac , Mexico '23 Abbott, Clarence E , Gen'l Supt , Iron Mines Div , Tenn Coal, Iron & R R Co , 1405 Minnesota Ave , Bessemer, Ala '04 Abbott, Louis Benjamin, Chief Engr , Consolidation Coal Co , Elkhorn Div Jenkins, Ky '15 Abbott, Robert R , Met Engr , Peerless Motor Car Co Cle veland, Ohio '12 ||Abbott, Wells Osborn, Ray Consolidated Copper Co Hayden, Ariz '23 Abeel, George H , Jr, Cons Min Engr 4612 W 17th St, Los Angeles, Cal '18 Abel, Albert E, Asst to Pres, Valley Mould & Iron Corpn Sharpsville, Pa '19 Abernathy, George Elmer, Prof Geol & Min , Kansas State Teachers College Pittsburg, Kans '20 Abey, Hiroshi, Min & Met Engr, Takata & Co , 2 Yeirakucho, Nichome, ICojimachi-ku, - Tokyo, Japan '17 ||Aborn, Robert H 24 Groveland St , Auburndale, Mass '19 Abouchar, Sylvain Sley, Min Engr & Geol , Care of S H Sekaly, 13 Rue El Nimr, Cairo, Egypt '17 ?Abraham, Arthur W 1626 N Alexandria Ave, Los Angeles, Cal '21 Abrahams, Alexander I, Gen'l Mgr, Ricon Electrical Co Slough, London, England '13 ||Abrahamson, C Walter, Min Engr, Brule Min Co Stambaugh, Mich '21 Abrams, Charles Jackson, Mill Supt, Utah Apex Min Co Bingham Canyon, Utah '21 Abrams, David H, Cons Min Engr 182 Worth St, Johnstown, Pa '20 ?Acker, E O'C , Met 128 East Washington Lane, Germantown, Philadelphia, Pa '86

Jan 1, 1923

By H. W. Camp

Although the situation in the oil industry during the past year has not been conducive to large expenditures for development and research, there is little indication that such expenditures have been curtailed. While few outstanding achievements have been reported, considerable progress has been made in the development of new product,s and the adaptation of petroleum derivatives to new uses. The most important question facing the refiner today is the antiknock quality of his gasoline. This year has seen the widespread adoption of the term "octane number" as a measure for anti-knock values, and in the latter months of the year the public has been made acutely aware of this condition through competitive advertising. Gasoline is no longer priced on volatility and gravity alone, but on octane number as well; and premiums are being paid for material of relatively high octane rating. The situation has grown more and more competitive and has forced refiners continually to raise the octane rating of their regular and competitive grades, and at this writing the same situation exists for premium grades which have possessed relatively high anti-knock properties for some time. Straight-run gasoline produced from paraffin-base or semiparaffin-base crudes has an inherently low anti-knock value, and in order to convert this material to a higher quality it has been found necessary to crack an increasing percentage of the crude oil charge. By completely cracking the heavier portions of the crude and blending back with the straight-run gasoline, it has been possible to produce an average of 63 to 65 octane number gasoline on average Mid-Continent crude. This operation carried to the fullest extent does not suffice, however, and the recent and rapid development of the so-called '(reforming unit," has resulted. The straight-run gasoline fraction is cut into two parts: a light, low boiling point gasoline; and a heavy gasoline or naphtha. The latter containing the low anti-knock portions of the gasoline, is sent through a re-forming unit and subjected either to high temperature or pressure, or both, which materially increases its octane number. On average Mid-Continent the blend of low boiling point straight-run,

Jan 1, 1932

By John T. Galey

Production of crude oil for 1940 in southwestern Pennsylvania was off nearly 70,000 bbl., largely as a result of the great number oi abandonments, together with the lack of extension of the Washington and Green County pools. Oil wells completed numbered 51, which is 26 more than last year, but the total initial production of 259 bbl. is only 18 bbl. greater than in 1939. There was an increase of 72 over last year for a total of 209f gas wells. However, 68 7 dry holes were drilled, which is 40 more than a year ago. Thus, 328f wells were drilled during the year, and rigs are erected or drilling is progressing on 59 t more. Shallow Development Oil.—Butler County led in number of oil wells completed, with a total of 27 for an initial production of only 69 bbl. Washington County, with 12 new oil wells, one of which made 40 bbl. from the Fifth sand in S. Franklin township, has 95 bbl., while in Allegheny County 9 wells gave an initial of 86 bbl. for the highest Per well average in the area. This initial was given a considerable boost by one 35-bbl and another 2;-bbl. well in West Deer township, where the Fourth sand produced at 1840 feet. Greene County had only one oil well completed during 1940, and Washington County had 12. The subnormal totals for these counties may be explained by the higher cost of completions and the declining price of crude. The first price change in crude during the year occurred on May 22, when a 25 cut was made. A second 25 cut was made July 12, and was followed by a 156 cut on .Aug. 28. This price held until Nov. 12, when there was a restoration of 156. On Dec. 17 a second 156 increase was put into effect, bringing the price to $I.So per barrel. Gas The large increase in the number of gas wells completed may be attributed to three factors; namely, the recently discovered production possibilities of moderately deep, hitherto little tested horizons, together with increased demand and price. The latter has been made possible by a recent decision of the court, which ruled restraining the public service Commision's prohibition of a raise in the minimum monthly charge to small consumers by one of the major gas companies. A portion of the revenue derived in this manner is being passed along to the producer in the form of higher prices in the field. This higher field rate will remain in effect until a new ruling is made, when it will be reduced in proportion to the reduction of the monthly minimum charge. In an effort to extend the chambers Dam Fifth sand oil pool southwest from Amwell township, Washington County, several wells have been drilled. One of these, in Morris township, washington County, had an initial of 3.2 million cu. ft. open flow from the Big Injun sand. This indicates an entirely new productive area for the latter horizon. Allegheny County had one spectacular well in South Fayette township-—at a depth of about 2500 ft. a 4-million-CU. ft.

Jan 1, 1941

By John T. Galey

Production of crude oil for 1940 in southwestern Pennsylvania was off nearly 70,000 bbl., largely as a result of the great number oi abandonments, together with the lack of extension of the Washington and Green County pools. Oil wells completed numbered 51, which is 26 more than last year, but the total initial production of 259 bbl. is only 18 bbl. greater than in 1939. There was an increase of 72 over last year for a total of 209f gas wells. However, 68 7 dry holes were drilled, which is 40 more than a year ago. Thus, 328f wells were drilled during the year, and rigs are erected or drilling is progressing on 59 t more. Shallow Development Oil.—Butler County led in number of oil wells completed, with a total of 27 for an initial production of only 69 bbl. Washington County, with 12 new oil wells, one of which made 40 bbl. from the Fifth sand in S. Franklin township, has 95 bbl., while in Allegheny County 9 wells gave an initial of 86 bbl. for the highest Per well average in the area. This initial was given a considerable boost by one 35-bbl and another 2;-bbl. well in West Deer township, where the Fourth sand produced at 1840 feet. Greene County had only one oil well completed during 1940, and Washington County had 12. The subnormal totals for these counties may be explained by the higher cost of completions and the declining price of crude. The first price change in crude during the year occurred on May 22, when a 25 cut was made. A second 25 cut was made July 12, and was followed by a 156 cut on .Aug. 28. This price held until Nov. 12, when there was a restoration of 156. On Dec. 17 a second 156 increase was put into effect, bringing the price to $I.So per barrel. Gas The large increase in the number of gas wells completed may be attributed to three factors; namely, the recently discovered production possibilities of moderately deep, hitherto little tested horizons, together with increased demand and price. The latter has been made possible by a recent decision of the court, which ruled restraining the public service Commision's prohibition of a raise in the minimum monthly charge to small consumers by one of the major gas companies. A portion of the revenue derived in this manner is being passed along to the producer in the form of higher prices in the field. This higher field rate will remain in effect until a new ruling is made, when it will be reduced in proportion to the reduction of the monthly minimum charge. In an effort to extend the chambers Dam Fifth sand oil pool southwest from Amwell township, Washington County, several wells have been drilled. One of these, in Morris township, washington County, had an initial of 3.2 million cu. ft. open flow from the Big Injun sand. This indicates an entirely new productive area for the latter horizon. Allegheny County had one spectacular well in South Fayette township-—at a depth of about 2500 ft. a 4-million-CU. ft.

Jan 1, 1941

By R. I. Garrod, R. A. Coyle

The shapes and positions of X-ray reflections from specimens of copper, steel, and aluminum alloy haue been examined in the elastic and plastic ranges both while the specimen was under stress and in the unloaded condition. For the aluminum alloy the shape was unaltered by the application of stress either within the elastic limit or in the plastic range provided that no additional plastic strain was induced. In copper the broadening accompanying plastic deformation was very slightly reduced when the specimen was unloaded. A similay but more marked elastic component of broadening was also found for steel, but in this case below the yield stress. Line profiles corrected for instrumental and particle-size broadening indicate very large internal stresses in local regions of the plastically deformed metals. The results are discussed in terms of a recent suggestion that the heterogeneous dislocation distribution between the cells and their boundary walls plays a major role in the peak shifts and broadening of the X-ray reflections. STUDIES of the X-ray line profiles from strained polycrystalline aggregates concentrate usually on one or the other of two main parameters: a) the displacement of the peak of the intensity contour from its position for a strain-free aggregate, or b) the shape of the profile. From peak shifts data can be obtained either on the relation in both the elastic and plastic ranges between applied external stress and average lattice strains in a given (hkl) direction, or, alternatively, on the residual lattice strains which are present after a plastically deformed specimen is unloaded.' On the other hand, the shapes of the broadened profiles from cold-worked metals can be analyzed to separate the broadening produced by small particle size and by heterogeneous lattice strains.' In this paper the terms "size broadening" and "strain broadening'' are used in the general sense adopted by warren.' In the past, apart from two early qualitative observation, it has been customary to examine only the movements of the peaks of the profiles while the specimen is actually under load, since the line broadening induced by plastic strain remains after removal of the external stress. Consideration of the implications of existing data of this type suggests, however, that fruitful additional information on a number of fundamental aspects might be gained by careful examination of whether the X-ray line profile is in fact different in the loaded and unloaded states of the specimen. By taking advantage of the sensitivity and convenience of modern diffractometer techniques it is possible to explore with relative ease the magnitude and importance of any elastic effects which may be superimposed upon the well-known permanent changes in profile. The main aim of the work to be described was thus to investigate this point for typical metals and alloys. For this purpose annealed specimens were extended first elastically and then plastically and the positions and shapes of X-ray reflections were recorded. Initially it was anticipated that prime interest would center on observations within the plastic range; it has been found, however, that small changes in profile sometimes occur both before and after the nominal elastic limit of the material is reached. It is shown that the results obtained have important implications in relation to the structural changes and processes associated with deformation. I) EXPERIMENTAL To enable the diffraction lines to be recorded while the specimen was under uniaxial-tensile stress, a small hydraulic testing machine was designed and constructed for direct attachment to the goniometer of a Philips diffractometer. The specimens, which were machined from 1/2-in.-diam rod and had a central rectangular section 3/8 by 1/16 in. over a gage length of 1 in., were held in the machine by split collets mounted in grooves in the cylindrical ends of each specimen. No special precautions were taken to ensure precise axiality of loading. Constant oil pressure was maintained by a lever and weights system and transmitted to the loading rig by flexible pipe. The actual load on the specimen was measured by a load cell in the machine to an accuracy of * 1 pct. To enable smooth X-ray profiles to be obtained the specimen and machine were oscillated continuously during recording through *7-1/2 deg about the normal half-angle position of the goniometer. The three materials chosen for the investigations were high-purity copper as representative of a ductile fcc metal, a low-carbon steel for a bcc metal, and an aluminum alloy as a material in which the proof stress/ultimate strength ratio is high. Details are as follows. a) Copper. 99.999 pct purity. After machining the specimen surface was polished mechanically and

Jan 1, 1964

By D. E. Thomas, C. E. Birchenall

ALTHOUGH Eoltzmann gave a mathematical solution for the diffusion equation (for planar diffusion in infinite 01. semi-infinite systems only) in 1894 allowing for variation of the diffusion coefficient with a change in concentration, it was not until 1933 that this solution was applied to an experimentally investigated metallic system. The calculation was carried out by Matano' on the data obtained by Grube and Jedele3 for the Cu-Ni system. Since that time concentration dependence of the diffusion coefficient has been demonstrated for many pairs of metals. However, the nature of this dependence has never been fully elucidated. Many investigators have suspected that these variations could be related to the thermodynamic properties of the solutions, one of the earliest explicit statements being contained in a discussion of irreversible transport processes by Onsager' in 1931. Development along these lines has been greatly retarded by the lack of reliable data on the variation of tliffusivity with concentration, the paucity of the thermodynamic data for the same systems at the same temperatures and compositions, and an incomplete understanding of the relation of the thermodynamic properties of the activated state for diffusion to the bulk thermodynamic properties. The last factor has been discussed by Fisher, Hollomon, and Turnbull.5 In many instances where data exist, it is difficult to know which are acceptable. This problem probably applies more strongly to diffusion data than to activity measurements. For instance, four sets of observers"-" have reported self-diffusion coefficients for copper. The average spread between extreme results is a factor of about four, though the individual sets of data are self-consistent to about 20 pct. Thus one or more factors are out of control, at least in these experiments, making estimates of internal error unreliable. The most reliable diffusion data in most systems have resulted from the use of welded couples with a plane interface from which layers for analysis are machined parallel to the interface after diffusion. The layers are analyzed, and the result is a graphical relation between distance and concentration, usually called the penetration curve. Given the same set of analytical data and distances and following the same procedure in computation, different observers will generally produce diffusion coefficients which vary appreciably, especially at the extremes of the concentration range. Experiments must be carefully designed so that the precision is good enough to answer a particular question unequivocally. In the first calculation of the dependence of the diffusion coefficient on concentration in the metallic solid solution Cu-Ni, Matano found that the coefficient was insensitive to concentration from 0 to 70 pct Cu, after which it rose more and more steeply to some undetermined value as pure copper was approached.' The same behavior was reported for Au-Ni, Au-Pd, and Au-Pt.* The data used were those of Grube and Jedele which were very good at the time, but are not considered particularly good by present standards. Furthermore, the method of calculation makes the ends of the diffusion coefficient-concentration curve unreliable. For better reliability, the high copper end of the curve has been checked by incremental couples, where the concentration spread is 67.7 to 100 atomic pct Cu. The implication of the curves calculated by Matano was that diffusion is very concentration sensitive in one dilute range of this completely isomorphous system and hardly at all in the other. Matano's result is confirmed. Later Wells and Mehll0 published data on diffusion in Fe-Ni at 1300°C, which represent a thorough test of the shape of the concentration dependence curve. They ran couples with the following ranges of nickel concentration: 0-25 pct, 1.9-20.1 pct, 0-20.1 pct, 20.1-41.8 pct, 0-99.4 pct, and 79.3-99.4 pct. Although the trend of the data indicates an S-shaped concentration dependence, their curve was drawn to the pattern set by Matano. Their original data have been recalculated for the 0-99.4 and 79.3-99.4 pct couples. Wells and Mehl's points and two independent recalculations from the raw data are plotted in Fig. 1. What appears to be the best curve is drawn through them. This curve shows little sensitivity to composition in both dilute ranges with a strong dependence at intermediate composi-tions.? Similar experiments on the Cu-Pd system are reported here at temperatures where solubility is unlimited. These lead to the same type of concentration dependence for the diffusion coefficients as was found upon recalculation of the data for the Fe-Ni system. Experimental Procedure Cu-Pd: The concentration dependence of the diffusion coefficient may be determined by the use of

Jan 1, 1953

By Arthur S. Dwight

THE last decade of the 19th century was a peculiarly interesting one in. the annals of American metallurgy, especially as concerns the lead and copper- smelting industries; and it may be interesting to review briefly one of the outstanding incidents of that period, the development of the mechanical roasting furnace. I shall not pretend, in these reminiscences, to give with absolute accuracy the sequence of events or dates, nor to present a complete history of the period, but shall seek merely to 'sketch a more or less impressionistic picture with some of the underlying facts and causes as the recollection comes back to me and then point out how the present-day practice grew out of those activities. My acquaintance with the developments in Montana was based on occasional visits and general collateral information, but in Colorado I lived through the episode and was of it.

Jan 1, 1921

By A. Vignes, J. P. Sabatier

A study of ternary diffusion at 1315°C in the Fe-Co-Ni system covering the entire ternary phase diagram has been carried out. Experimental values of the four interdiffusion coefficients DFeNico,DFeCoCo, DFeCoNi were computed at 33 points of the ternary diagram. The limiting values of these coefficients on the three sides of the ternary diizgram have also been determined. This set of data is presented as a contour map on the ternary isotherm for each of the four coefficients. Assuming that the Fe-Co-Ni system can be considered as ideal, the phenomenological coefficients Lk ij (with k = Fe) have been computed and the Onsager reciprocal relutions verified. It is shown that, in the Fe-Co-Ni system, the diffusion process can also be described by only two interdiffusion coefficients DFeFe and DCoNiFe, the second cross diffusion coefficient DCoFeNi being equal to zero and the second direct difusion coefficient being given by The values of the cross interdiffusion coefficients and of the Onsager coefficients are explained in terms of atomic mobilities of the three components with the help of a kinetic calculation due to Lane and Kirkaldy.8 It is shown that all the results are explained if the tracer difusion coefficients of the three components are such that DFe > DNi ~ DCo in complete agreement with experimental data on the three binary systems. DIFFUSION in a ternary alloy system is basically and significantly different from diffusion in binary alloys. In binary diffusion, there is just one independent composition variable and only one coefficient Dij is needed to describe the interdiffusion process. In ternary diffusion, we must allow for cross interaction between two independent species, and four interdiffusion coefficients are necessary to describe the transport process. Kirkaldy et al.1,2 have determined interdiffusion coefficients in the systems, Cu-Mn-A1 and Zn-Cu-Al. Guy and Leroy4 have reported intrinsic diffusion coefficients for the r phase at 1300°C of Co-Ni-Cr alloys as a function of composition using the analysis of Philibert and Guy.3 Interdiffusion coefficients were measured at three different compositions at 850°C in the single phase copper-rich corner of the Cu-Zn-Mn system by Dayananda and race.5 Zie-bold and Ogilvie6 have determined interdiffusion coefficients in the single-phase field of the Cu-Ag-Au system at 725°C. Preliminary results on diffusion at 1136°C in the system Fe-Co-Ni have been reported.7 In this study, data are reported on a more complete determination of interdiffusion coefficients in the Fe-Co-Ni system in the entire ternary at 1315°C. There is complete solid solubility with the fcc structures at 1315ºC, and this system can be considered as nearly ideal. This approximation allows the computation of the Onsager phenomenological coefficients. These values can then be used to test a kinetic calculation of the Onsager L coefficients in ternary substitutional solid solutions due to Lane and Kirkaldy.8

Jan 1, 1970

By B. L. Landrum, P. B. Crawford

Theoretical and potentiometric model studies have been made of the effect of non-uniform lateral permeabilities on pattern sweep efficiency and production capacity in waterflood and gas-cycling programs. It is shown that a diflerence in directional permeability by a factor of three may result in a sweep efficiency of only 43 per cent for a five-spot pattern or a sweep of either 79 or 38 per cent for a direct line-drive square pattern, depending on the direction of the line-drive flood. Changes in the pattern conductivity varied from about 0.8 to 1.34 over this same permeability variation, depending on the pattern used. It is suggested that measurements be made to determine the possible magnitude and extent of the directional permeability phenomenon early in the field developinent and certainly prior to the initiation of any fluid-injection progmm. INTRODUCTION Irregularities in reservoir sand properties long have been a major difficulty to anyone attempting to explicitly describe the field characteristics of oil production. In particular, it is well known that vertical and lateral permeabilities often differ appreciably; however, the existence of large regions with lateral permeabflity variation is not widely recognized. A number of years ago, extensive studies were conducted by the Secondary Recovery Research Labcratory of the Pennsylvania Grade Crude Oil Association, primarily on the Bradford field. Johnson and Hughes' reported a permeability trend in the northeast-southwest direction. They indicated that flow in the preferred direction may be 25 to 30 per cent greater in that direction than in the northwest-southeast direction. They also reported that similar effects may be found in other nearby fields. The origin of the permeability variation has been discussed by Griffith Hutchinson' described the results of labora- tory tests on limestone cores, pointing out that per-ferential directional permeabilities were significant in one-half of 10 formations studied and that the average permeability ratio was 16:1. Barfield, Jordan and Moore analyzed the fluid-injection displacement performance in the Spraberry and reported that the effective ratio of permeability parallel to the major axis to the permeability perpendicular to this axis was 144:l and that it inclined along an angle of about 30". To prevent the reduction of sweep efficiency which would normally result from flooding or cycling in such reservoirs, well spacing could be varied from the customary square to a diamond-shaped pattern. Johnson and Hughes' presented a method for determining the desired shape. Another method will be discussed in detail in the next section. It is the purpose of this paper to investigate quantitatively the effect of directional permeability upon the sweep efficiency and production capacity of the five-spot and line-drive well patterns. Information currently in the literature will be applied to this particular problem and augmented by a potentiometric model study. It is stressed that the effects herein discussed may or may not be of great importance because field data on this phenomenon are far too scant to form such an opinion. It is suggested that, if conditions similar to those found by Johnson and Hughes frequently exist (as may well be the case), more consideration cdrtainly should be given to this problem.

By P. R. Sperry, A. P. Beck

It has been shown1 that in poly-crystalline strips of high purity aluminum with a fairly random orientation distribution, grain growth progresses gradually until the average grain diameter reaches a value approximately equal to the strip thickness. Recent work at this laboratory led to the realization that grain growth might be impeded to a considerable extent in the presence of a sharply defined texture, where orientation differences between neighboring grains are small. In order to investigate this effect the following experiment was carried out with the same lot of high purity aluminum previously used for grain growth studies in randomly oriented material.' Very large grain size was developed by grain growth at 650°C in specimens of 0.200 in. thickness. These specimens were then rolled to a thickness of 0.050 in. or 1.25 mm—a reduction of 75 pct. In the rolled strip each large grain corresponded to an elongated area easily identified by etching. After annealing for 1 to 25 min at 600°C and re-etching, these elongated areas were again recognizable. Within each area, corresponding to a single large grain before annealing, there formed by recrystallization a multitude of new grains with a fairly well developed preferred orientation. The orientation and the size of the new grains formed in areas corresponding to different large grains, varied widely depending on the orientation of the parent grains with respect to the rolling direction and the plane of rolling. Many areas were found where the average grain size was considerably smaller than the specimen thickness. Such an area occurred in a specimen cut in half before annealing. One half, containing a portion of the area in question, was annealed 1 min at 600°C, the other half, with the remaining portion of this area, for 25 min at the same tempera-Aluminum killed low carbon steel, § which is now used extensively for severe deep drawing or other difficult forming operations, is unusual in that its grain structure, after cold reduction and box annealing in accordance with conventional continuous sheet or strip mill practice, often is elongated, although at times it is equiaxed. Since this unusual structure has been found superior for many, but not all, severe forming operations, recrystallization of the steel, both at constant temperature and on continuous heating, was investigated and compared with that of rimmed steel in the hope that something might be learned about the mechanism of, and the factors controlling, the formation of such elongated grains. In this structure, the grains are elongated both in the lengthwise direction of the strip and transverse to this direction, even though nearly all of the extension in both hot and cold rolling is in the lengthwise direction. The grains are thus roughly pancake-shaped, being longer and wider than they are thick, as observed also by Burns and McCabe,1 and as illustrated by the typical structures shown in Fig 1. Fig la, representing a conventional longitudinal section, shows the length and thickness of the grains, whereas Fig Ib shows their length and width as seen by examining a section parallel to the sheet surface. Both illustrate the very irregular grain boundaries usually associated with the elongated grain shape. A finer equiaxed grain structure in this same grade is shown in Fig Ic. Either the elongated or the equiaxed structure may be present in the annealed product, and in rare instances the two types may coexist in a single specimen, as shown in Fig 1 d. Isothermal Recrystalliza-tion of Rimmed and Alamimum Killed Steel An aluminum killed steel known to have an elongated grain structure after conventional processing (Steel B, Table l), was selected for the initial recrystallization studies; for comparison, a rimmed steel, A in Table 1, was used. Samples of each in the form of hot rolled strip 0.075 and 0.095 in. thick, respectively, were cold rolled on a small laboratory mill in steps of about 0.010 in. per pass to obtain total reductions of 40 and 60 pct. Small pieces of the cold reduced strip were heated in lead at selected constant temperatures for one of several periods of time, then cooled in air. Rate of heating in the lead was, of course, very fast. Hardness of the cooled specimen was measured and a longitudinal section examined metallographically. Isothermal recrystallization curves for these two steels at 1050°F, based on hardness of the air cooled specimens, are shown in Fig 2 in which the amount of recrystallization corresponding to each plotted point is indicated. The marked difference in the behavior of these two types of steel is evident. After a corresponding amount of cold reduction, the rimmed steel recrys-tallizes in a much shorter time than the killed steel and the shape of its recrystallization curve, (plotted on a logarithmic time scale), is very different. The curve for rimmed steel indicates that recrystallization is analogous to isothermal transformation of aus-i.enite in that it proceeds at a progressively faster rate up to some 50 pct recrystallization, then at an increasingly slower rate. For the aluminum killed steel, however, the start of

Jan 1, 1950