Search Documents

Report of Secretary TO THE BOARD OF DIRECTORS OF AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS Gentlemen -I have the honor to present the following report for the calendar year 1920 The activities which-seem to call for special com¬ment are THE NEW FORM OF MAGAZINE MINING AND METALLURGY appeared every month during the calendar year and has been developed until it contains some ten departments It has brought forth more commendatory letters than have been received at headquarters on any other subject throughout the year Less than a dozen letters unfavorable to the change have been received, and the indications are that the magazine has met a want deeply felt, especially by members distant from headquarters The technical papers printed by the Institute are published in abstract in the magazine and opportunity is given to members who desire them to receive full copies of any or all papers published The Bound Volumes, as usual, contain all the papers in full and discussions thereof FINANCES The greatly increased cost of paper and printing has put a tremendous burden on the Institute's finances, since the dues of $12 per year are only 20 per cent greater than the members paid when the Institute was founded forty-nine years ago This has resulted in a temporary deficit, similar to that encountered by many of our sister engineering societies The fact that our Institute has lower dues and gives more in the way of publications to its members than any other of\the national engineering societies has rendered the situation more difficult for us MEETINGS The Annual Meeting in New York, the Field Meeting in the Lake Superior District, the meeting of the Petroleum and Gas members at St Lours, and of the Institute of Metals Division in Columbus, Ohio, have all been described in full in the magazine

Jan 1, 1923

By K. E. Nelson

The effect of thorium and zinc variations on the strength and 100-hr creep characteristics of Mg-Th-Zn-Zr alloys was investigated. Optimum resistance to creep at 650° and 700°F are attainable within a certain range of thorium and zinc contents. This range does not conform to that which develops maximum tensile properties. RAPID advances have been made during the last few years in the development of magnesium alloys for elevated temperature applications demanding high resistance to creep. The beneficial effect of rare-earth metals on the creep resistance of magnesium alloys has been emphasized by a number of publications1-13 and such alloys are now in commercial production. The use of thorium as an alloying ingredient in magnesium was mentioned by McDonald and also in two Alien Property Custodian patent applications.10,17 The initial observation of Sauerwald that thorium contributes still higher creep resistance to magnesium than is attainable with rare-earth metals has recently been substantiated.'" " In fact, it has been demonstrated that the useful temperature range of magnesium alloys is appreciably extended by the use of thorium. In all cases, it was observed that zirconium must be included in the alloys in order to render them fine grained and more readily castable. Several recent publications:2-27 indicate that a still further improvement in creep resistance and a further extension of the useful temperature range can be realized by the addition of zinc to alloys. The primary purpose of this paper is to present the results of a comprehensive study of the effect of zinc on the strength and creep characteristics of Mg-Th-Zr alloys. Compositions covering the range of thorium content from M to 6 pct and zinc content from 0 to 5 pct have been investigated. The creep characteristics at 650" and 700°F reported in this paper are based on results of tests of 100-hr duration. It is appreciated that creep tests of 100-hr duration might not yield adequate data for design purposes for parts with much longer expected life. However, for the purposes of the present discussion, it is felt that the combination of stresses and temperatures used in the 100-hr creep tests have yielded a clear representation of the compositional variation of creep resistance at the temperatures investigated. Creep tests of 1000-hr duration are now in progress on a few of the most promising alloys. Preparation and Testing of Alloys The alloys studied in this intensive investigation were prepared in 25 lb capacity mild steel crucibles. The thorium, zinc, and zirconium were alloyed and poured as described in earlier publications The thorium was introduced into the melt in the form of a Mg-Th hardener," the zinc added in the metallic form, and the zirconium alloyed in the form of the commercial hardener containing magnesium and 30 to 50 pct Zr.10, 26 Fluxing practices for melting and refining were the same as for magnesium-rare-earth metal-zirconium alloys. The melts were sampled for analytical determinations and poured into separately cast 1/2 in. diameter standard tensile bars. The test bars were given a precipitation treatment of 16 hr at 600°F in laboratory furnaces. It has been shown by other tests that a high temperature solution treatment followed by an aging treatment is unnecessary for the development of optimum properties in Mg-Th-Zn-Zr alloys. The selection of 600°F as the aging temperature was based on an attempt to achieve metallurgical stability without coalescence of the undissolved phases and the attendant loss in strength. The thorium, zinc, and zirconium contents of each melt were determined chemically. The zirconium contents are reported in two parts, "soluble" and "insoluble," referring, respectively, to the portions present in the alloy which are soluble and insoluble in dilute HCl acid. Distinction is being made between these two components of the zirconium content in the alloys because it has been found that only that portion of the zirconium content which is soluble in dilute inorganic acids affects the structure and properties of the alloys. The usual impurities consisting of copper, iron, manganese, and nickel were determined spectroscopically. The analysis for each melt is listed in Table I. A description of the methods of tension and creep testing has been detailed in earlier papers. The tests were performed with the cast skin re-

Jan 1, 1954

By F. G. Tahmoush, N. J. Grant, E. P. Abrahamson

The effect of grain size on the brittle -ductile transition temperature of pure iron and three dilute Fe-W alloys has been investigated by slow bend tests. The brittle-ductile transition temperature for pure iron increased with increasing grain sizes from 8000 to 500 grains per sq mm where the transition temperature then decreased with further increase in grain size. The dilute additions of tungsten lowered the transition temperature for fine grain sizes, suppressed a reversal of the curve in the coarse grained portion, and raised the transition temperature for this region. The frequency of twin occurrence increased with increasing grain size and decreasing temperature. The object of the present investigation was to re-examine the effect of grain size on the brittle -ductile transition of pure iron and several dilute Fe-W alloys. Current literature normally presents a simple relationship between grain size and the brittle-ductile transition temperature, namely, that the transition temperature increases with increasing grain size. Heslop and etch' have studied the transition temperature of mild steel by V-notch Charpy impact tests for the grain size range between 200 and 6000 grains per sq mm. The result was a linear plot of In 1-1/2 vs brittle-ductile transition temperature, where 1 is the grain diameter. Recent experiments by sipos2 revealed the possibility of a reversal in the slope of the grain size vs transition temperature plot for pure iron; however, his investigation was limited in scope, and the data obtained were insufficient to permit a definitive curve. The present investigation was undertaken in an effort to confirm or extend the grain size effect observed in iron by Sipos. PROCEDURE All alloys were vacuum induction melted, using 99.95 pct Fe containing 0.03 pct 0 and 0.004 pct C. Four ingots were made, ranging from pure iron to iron with 0.035 pct W. The chemical composition of each alloy, after processing, is given in Table I. The four alloys were prepared as 45 lb heats and cast into 4 in. diam by 16 in. molds. They were then extruded into 3/4 in. rods at 1800oF. Specimens for chemical analysis, taken from various positions along the rods, revealed no variation in tungsten content along the length. The extruded rods were reduced to 0.156 in. diam stock by a series of cold swaging operations involving intermediate vacuum annealing treatments. This procedure yielded a final cold reduction in area ranging from 10 to 90 pct. The swaged rods were chemically cleaned, cold pressed to a cross section of 0.10 by 0.18 by 1.0 in. long (2.54 by 4.73 by 25 mm). The specimens were wrapped in iron foil and vacuum sealed (10-4 mm Hg) in quartz. Various heat treatments at temperatures from 700" to 1300oC were utilized to produce grain sizes from 8000 to 1 grain per sq mm. Grain sizes were determined by measuring the average area of grains in a polished section. In specimens with grain size greater than 20 grains per sq mm, the total number of grains in the cross section was counted and then divided by the area to yield grains per sq mm. Grain size was measured both for longitudinal and transverse cross sections. The average of the two measurements was plotted vs transition temperature. An Instron Table Model testing machine was used to determine the transition temperature of specimens tested in three point horizontal bending. The specimen was supported by two 1/4 in. dowels one in. apart. Bending was accomplished with a push rod, the end of which had an 1/8 in. radius. The head speed was 50 in. per min. Temperatures were established through the use

Jan 1, 1963

P. E. McKinney,* Washington, D. C.-Observation made after examination of a number of defective gun forgings, together with a history of their manufacture, has strongly suggested that so-called "flakes" and woody or fibrous fractures are not necessarily analogous and are often caused by entirely different conditions. While some flaked bars may show fibrous areas in the fracture, it does not necessarily follow that the conditions causing these areas are the same as cause the fibrous, or so-called laminated, structures so commonly met in gun forgings subject to transverse tensile test; the fibrous structure formed in some flaky bars are merely incidental to the conditions causing the flakes. It is believed that the so-called flakes, or bright silvery spots, are mainly due to inherent physical defects in the steel, which existed at the very origin of the steel, rather than metallographic defects caused by subsequent irregularities in mechanical or thermal treatment. While great care in forging and treatment may, in a measure, tend to overcome the evil effect of the defects, with many heats of ingots, no such precautionary measures are needed to produce perfect forgings- and with such heats of steel it would be impossible, no matter how carelessly handled, to produce intentionally a forging containing the defects commonly known as flakes. It has been found possible, on several occasions, to actually predict flaky forgings from an inspection f the ingot after it had solidified, and in such cases no amount of careful forging or heat treatment would prevent the occurrence of such defects in the forging. The inspection of the physical condition of the ingot, and especially the character of the shrinkage on. the top of the ingot, has been given too little thought and study in this connection.

Jan 5, 1919

By R. D. Vaughn

The analysis of laminar flow of power-law non-Newtonian fluids in narrow, eccentric annuli is employed in this paper to discuss the problems of lubricant flow in journa! bearings and of errors introduced by eccentricity in experimental studies with concentric annuli on extruders and wellbore annuli. The velocity profile and pressure loss-flow rate equations are developed for the laminar flow region. In addition, the expected error in flow rate and pressure-loss measurements for concentric annuli as a result of eccentricity is determined. For example, a 10 per cent displacement of the core of an almost concentric annul us would cause a 1.8 per cent decrease in the observed pressure loss for a fluid with a power-law exponent n of 0.25. The corresponding increase in the observed volumetric flow rate would be 7. 5 per cent. INTRODUCTION Non-Newtonianism and eccentricity occur simultaneously in two engineering problems: (1) flow of lubricants in journal-bearings and pressure-reducing bushings, and (2) flow of non-Newtonian fluids in plastic extruders and wellbore annuli. The lubricants used for moving parts are often non-Newtonian in character — often they are plastic in behavior. A solution to the problem of flow of non-Newtonian fluids in narrow eccentric annuli is particularly pertinent to this problem. In all experimental studies of laminar flow of fluids in concentric annuli, such as in extruders and well casings, the error due to eccentricity must be estimated or studied. A number of publicationsl-4,6,7 have dealt with this problem for Newtonian fluids; however, I am not aware of work for non-Newtonian fluids. This work is directed to the non-Newtonian problem. Before the solution to the problem is given, the pertinent conclusions from the work on Newtonian fluids will be reviewed. Heyda 1 and Redberger and Charles 2 have published general solutions to the problem of the laminar flow of Newtonian fluids in eccentric annuli, apparently without knowing of the earlier work of Ca ld well 3 and Bairstow and Berry,4 which is reported by Dryden, et al. 5 Although several mathematical routes are encompassed by the work of these authors, the results appear to be equivalent. Redberger and Charles2 show that the error caused by eccentricity in concentric annuli is negligible for small diameter ratios (k < 0.5); however, for large diameter ratios (k + l), the error in the predicted flow rate can be as great as 100 per cent or more. Partial solutions to the problem are available from the work of Dryden,5 Tao and Donovan6 and Piercy, et a1.7 Tao and Donovan examined the case of flow in narrow, eccentric annuli (k + 1) with and without rotation of the annular core. These authors also reviewed previous work on this subject and verified their approach with experimental data. Dryden gives the solution for the limiting case of complete eccentricity or tangency. Piercy, et a l. published an early solution to the problem of narrow eccentric annular flow. The conclusions of Redberger and Charles2 and the experimental proof of Tao and Donovan6 both suggest that the region of large diameter ratios (k + 1) is of main interest and that the parallel planes approximation to the solution in this region is satisfactory. This method will now be extended to the laminar flow of non-Newtonian fluids in narrow eccentric annuli. THEORETICAL SOLUTION The geometrical aspects of the problem are illustrated in Fig. 1. To represent the non-Newtonian fluid the power-law model was selected. This model has many disadvantages which have been pointed out; nevertheless, its simplicity, its frequent and wide applicability justify its use in this work. Fredrickson and Bird8 and Savins9 have used it as a basis for a theoretical study of laminar flow of non-Newtonian fluids in concentric annuli.

Jan 1, 1966

By William Bent

THE dynamometer herein described is a modification of the one invented by Mr. Samuel Batchelder, of Boston, nearly forty years ago, a description of which may be found in the Journal of the Franklin Institute, 1843, vol. xxxii, p. 277, and in the Scientific American of August 31st, 1878. The modification consists in providing a method of making an automatic record, and of indicating more minute variations of the power transmitted. The improved dynamometer was designed by the writer in 1877, and was built a few months since by the Class of 1879 of the Stevens Institute of Technology. The accompanying cut, taken from the Annual Announcement of the Stevens Institute, represents the dynamometer without the recording attachment. It consists, as shown, of two stout cast-iron frames, held together by bolts in bearings, in the top of which frames run two shafts, each carrying a pulley at its outer end and a bevel gear-wheel of 45° at its inner end. One of these shafts is the driving-shaft, connected by belt to the engine or other prime mover; the other is the driven shaft, connected by belt to the machine driven. The power is transmitted from one shaft to the other through two other bevel-wheels of 45° gearing with the first, the shaft common to them and on which they run freely being at right angles to the axis of the two shafts first mentioned, and carrying at one extremity a heavy pendulum. The bevel-wheels being connected, as shown, and the power being applied to the driving-wheel, the two intermediate wheels with their common shaft have a tendency to revolve around the driving-axis, which tendency is a measure of the force transmitted, and is resisted by the moment of the weight of the pendulum. In the Batchelder dynamometer the four bevel-wheels and their shafts are used, but

Jan 1, 1880

By Wm. J. Wright

RECORDS of crude oil in India date back for nearly 100 years, and modest attempts were made to develop the oilfields of Assam about 75 years ago. We have no record of production until 1892 when the fields near Digboi, Assam, yielded about 700 bbl. Since that time, the production of the Digboi fields has increased slowly, but steadily, and new fields have been opened at Badarpur, in Assam, and Khaur, in the Punjab, until the production in India in 1918 was about 293,700 bbl. and the possible production at the present time is approximately 300,000 bbl. per year. In the meantime, the English oil companies in India have been slowly adding to their holdings until they have taken up practically all of the promising territory that is readily accessible, and only about one-tenth of their properties has been touched by the drill. All the producing oilfields of India, and as far as we know all the prospective fields, are confined to areas underlain by rocks of Tertiary age. These rocks consist of more than 20,000 ft. of dark sandstones and shales, with the Nummulitic (Eocene) limestone at the base. In parts of Assam, the lower measures contain economic deposits of bituminous coal. In the Punjab, the upper part contains thick beds of conglomerate. Visible organic remains are rare; except in the limestone and the coal measures. In general, the hardness of the measures increases from top to bottom, but there is an alternation of relatively hard and soft beds throughout the whole series. The rocks are everywhere folded and, in some instances, severely faulted. The crests of eroded anticlines usually stand up as ranges of hills in which the individual ridges are underlain by the relatively&apos; hard beds. Thus structural features are suggested and often clearly defined on the topographic maps.

Jan 3, 1924

By G. W. Josephson

GRANULAR mineral products used primarily to form a protective and decorative coating on the weather surface of composition roofing are called "granules," "roofing granules," or "slate." The latter term is a relic of the early days of the industry, when crushed slate was the dominant type of granule in use. Asphalt roofing is made by saturating and then coating a continuous strip of felt with specially compounded asphalts. Granules are embedded in the hot asphalt on the top of the sheet, and mica or talc is dusted on the back. After passing through press rolls, the strip is looped on a conveyor for cooling and then cut into shingles or packaged as roll roofing. HISTORICAL DEVELOPMENT Although the durability and protective qualities of asphalt and tar have been known since the earliest days of recorded history, it was not until 1780 that the first forerunner of present-day composition roofing was developed.&apos; Large-scale expansion of the industry has taken place since 1900. At first the process consisted simply of dipping sheets of burlap or other fabric into a tank of molten tar or asphalt. The long strip of roofing was rolled up, for convenient handling, and the early experimenters soon found that it was necessary to dust the surface of their new "roll roofing" with some kind of material that would prevent the tarred surfaces from sticking together. Any finely divided, low-priced local material like sand or fine gravel served this purpose and from its application the roofing-granule industry grew. As time went on, other characteristics of a properly applied mineral surfacing were recognized. As with wooden shingles, tar and asphalt can be ignited by flying embers from nearby fires. It was found that by in- creasing the largest particle size to the maximum that could be success- fully embedded and by properly controlling the amount of smaller fractions retained in the grade, so as to cover the asphalt completely, a high degree of resistance to fire was attained.

Jan 1, 1949

By F. K. Pence

THE reduction of the firing of clay wares to a science has been one of the most difficult problems of modern ceramic engineering. The number of factors involved in the treatment of these wares has been such a complicated composite of the chemical and the physical properties that, according to the old practice, results depended rather on the art of the operator than on any scientific data available. The combined influence of the chemical and physical properties of clay minerals renders it difficult to apply the data obtained in one operation to the forecasting of details to be applied in another. In maturing clay-ware bodies by the application of heat, the chemical reactions involved are, in general, incomplete. The object frequently is to secure a certain physical quality, as density, color, or strength, rather than any particular chemical composition or development: This is more generally true of the so-called crude clay products. In the case of certain more high-grade wares, as the porcelains, it is necessary to reach the temperature required to bring about a certain molecular development or crystalline structure; but even here, time and temperature are at work and must be considered jointly. The conditions attending the firing of clay wares has led to the use of certain devices in the measurement of the progress of the firing process whereby the influence of the various burning factors on the clay composition under fire is indicated. In the simplest application of this practice, samples of the ware itself are so placed as to be drawn for observation at various intervals during the burn. Although the appearance is affected by the quick cooling treatment, by experience, this practice is successfully used, particularly in the brick industry. The settle of the setting of brick, as measured from the top of the kiln may also serve as a guide in the firing operation. Another example is found in the stoneware industry, where the practice of arranging test pieces made of the same composition

Jan 9, 1919

By Julius Pohlman

Considering the truly wonderful natural resources of the United States, and the variety and extent of uses for hydraulic cement at the present day, it seems strange that the manufacture of the artificial product called Portland cement has not been introduced here. Possibly the reason may be we have in different States of the Union rock deposits from which a cement can be obtained that is as good, and some claim even better, because of a more uniform quality, than the English product after it has been subjected to transportation across the ocean. One of these natural cement-rock deposits is found in the northern part of the city of Buffalo, and its manufacture has been carried on successfully for the past eleven years by the Buffalo Cement co., Mr. L. J. Bennett, President. The quarries cover an area of about two hundred acres, of which only twenty-five acres have been exhausted up to date; and the supply is assured for years to come. One acre yields on an average 80,000 barrels of cement; hence 12,000,000 barrels is a low estimate of what these quarries will yield before they are exhausted. According to the Geology of New York this cement-rock deposit is called the Water-Lime group, and forms in this section the uppermost member of the Upper Silurian. Its outcrop can be traced along the base of the second limestone terrace of Western New York, but at Buffalo a very large part of the overlying Corniferous limestone has been removed by natural agencies, leaving only about eight feet (six feet of rock and two feet of clay) on the top of the cement-rock, and thus furnishing the conditions for successful quarrying at a minimum expense. This rock is really an impure limestone, a mixture, as it were, of the underlying shales of the Onondaga Salt group with the overlying

Jan 1, 1889

By William Kent

THE dynamometer herein described is a modification of the one invented by Mr. Samuel Batchelder, of Boston, nearly forty years ago, a description of which may be found in the Journal of the Franklin Institute, 1843, vol. xxxii,.p. 277, and in the Scientific American of August 31st, 1878. The modification consists in providing a method of making an automatic record, and of indicating more minute variations of the power transmitted. The improved dynamometer was designed by the writer in 1877, and was built a few months since by the Class of 1879 of the Stevens Institute of Technology. The accompanying cut, taken from the Annual Announcement of the Stevens Institute, represents the dynamometer without the recording attachment. It consists, as shown, of two stout cast-iron frames, held together by bolts in bearings, in the top of which frames run two shafts, each carrying a pulley at its outer end and a bevel gear-wheel of 45&apos; at its inner end. One of these shafts is the driving-shaft, connected by belt to the engine or other prime mover; the other is the driven shaft, connected by belt to the machine driven. The power is transmitted from one shaft to the other through two other bevel-wheels of 45&apos; gearing with the first, the shaft common to them and on which they run freely being at right angles to the axis of the two shafts first mentioned, and carrying at one extremity a heavy pendulum. The bevel-wheels being connected, as shown, and the power being applied to the driving-wheel, the two intermediate wheels with their common shaft have a tendency to revolve around the driving-axis, which tendency is a measure of the force transmitted, and is resisted by the moment of the weight of the pendulum. In the Batchelder dynamometer the four bevel-wheels and their shafts are used, but

Jan 1, 1880

By John J. McKetta. Jr., Louis B. Lesem, George H. Fancher

The proration of oil produced in the field frequently is based partially or entirely upon the gas-oil ratio of wells. The measurement of the gas-oil ratio is one of the more important field tests in regulatory and pro-ration work, and the test always should be conducted according to standardized methods and procedure. Obviously, the gas-oil ratio and the volume of gas produced by a well depend upon many factors but should be independent of the method of measurement and of the devices used to measure gas and oil. Consequently, the volume of gas accompanying a barrel of oil produced by a well may be measured by any reliable and accurate device or instrument. Frequently either a critical flow prover or an orifice well tester is used for this purpose, and for a particular well the same rate of flow of gas should be obtained regardless of whether a critical flow prover or an orifice well tester is employed in the test. In Texas, when using either instrument, either Capacity Table 1 or 5&apos; is employed in making the necessary computations. If the tables are used, a discrepancy always is found whenever the two instruments are compared by extrapolation to the same conditions of flow. Clearly, Tables 1 and 5 must be at fault in some respects. The orifice well tester and the Bureau of Mines type of critical flow prover are essentially the same instrument; both devices utilize a square-edged orifice 1/8 in. in di-ameter as the primary element, and both freely discharge gas to the atmosphere. Tables for the orifice well tester&apos; have been published in the ranges of 0 to 15 in, of water and 0 to 40 in. of mercury (Hg) differential in pressure. Coefficients for the critical flow prover have been published for differentials in pressure greater than 75 psia. An extrapolation of either differs from the other set of data as much as 18 per cent at some points. No immediately obvious reasons for the discrepancy was found, and data available from the literature were insufficient to effect reconciliation. Consequently, a series of experiments was performed to check the available data and to determine discharge coefficients for the two devices in an overlapping range of differential pressure. The correlating equation used in preparation of tables such as Tables 1 and 5&apos; is the so-called hydraulic equation, Q = C1 vh .....(1) The tables cover orifice sizes from 1/8 through 1 1/4 in. A second set of tables, for use with greater differentials in pressure, apply only to the 3/4, 1, and 1 1/4-in. orifice plates over a pressure range of 0 to 40 in. of Hg. The correlating equation used in preparation of the tables is Q = C2 vH(29.32 + 0.3H)/G . (2) Each of these equations is valid only for the range to which it has been applied, and neither equation is valid for extrapolation. Theoretical equations for flow through an orifice are based upon assumptions of fractionless flow and an emergent jet the size of the orifice. A multiplier, C,, called the discharge coefficient, is inserted into the theoretical expression to compensate for both frictional losses and the contraction of the jet experienced in the plane of the orifice. Buckingham3 shows that C, should vary with the ratio of upstream to downstream pressure for flow of a compressible fluid at any average linear velocity through the orifice less than the velocity of sound. Work published by the National Advisory Committee for Aeronautics4 indicates that the variation continues into the so-called critical flow region until the vena contracta coincides with the plane of the orifice. The NACA work, however, does not indicate a leveling off of the coefficient. The work of the Bureau of Mines5 for the critical flow prover was based on differential pressures greater than 75 psi and indicates that the discharge coefficient, Cd, is constant in this region at a value of about 0.86.

Jan 1, 1958

Discussion of the paper of C. A. HEBERLEIN, presented at the New York meeting. February, 1915, and printed in Bulletin No. 98, February, 1915, pp. 497 to 504. H. D. PALLISTER, State College, Pa. (communication to the Secretary).-Mr. Heberlein gives some valuable information concerning a branch of mining and metallurgy which has been neglected during the last few years. His results with fine grinding and Deister tables suggest the possibility of the mining and concentration of a number of low-grade cinnabar deposits. Can Mr. Heberlein give us some idea as to the loss of quicksilver during this concentration? The advances in the metallurgy of quicksilver have been few and far between in recent years. Most miners prefer to go on in the old way with the Scott furnace and the large brick condensers. The large brick condensers are expensive to build and to keep in repair, and on account of the thick walls are extremely slow in cooling the gases; and further, the joints between the bricks offer passages for the quicksilver vapors unless great care is used in building the condensers.. The escape of vapor at the top of the furnace is another source of loss and I see the people at the Oceanic mine have overcome this in a very ingenious way. I recently returned from the Terlingua quicksilver district of Texas, where the only operating company, the Chisos Mining Co., is operating a 20-ton furnace of the Scott type. They had considerable difficulty with getting a good extraction, clue to too high heating in the furnace with its .resulting diffIculties. Recently they have been running with ashpit and fire doors closed and have been able to keep the heat lower, thus getting much better results and practically verifying the results obtained at the Oceanic mine.

Jan 5, 1915

By E. S. Machlin, C. W. Chen

THIS investigation is concerned with the origin of the intercrystalline voids and cracks formed in metals and alloys subjected to stress at elevated temperature. There have been many suggestions in the recent literature relating to this problem. Greenwood&apos; suggested that the voids may be produced by vacancy condensation. Zener has stated that shear-stress relaxation across grain boundaries could initiate high tensile stresses at the regions blocking grain boundary slip and thereby cause the formation of cracks. Chang and Grant3 have described the formation of cracks at grain boundary triple points and have experimentally verified Zener&apos;s mechanism for the grain boundary regions in the vicinity of a triple point. Subsequent to the completion of this investigation, Gifkins4 developed a model which made use of Stroh&apos;s5 mechanism of fracturing to produce sub-microscopic fractures that subsequently grow by grain boundary slip. Chen and Machlin,6 in answer to Gifkins, described a model deduced from the present investigation, in which grain boundary slip provides both the stress to fracture at grain boundary jogs and the deformation required to separate fractured jog surfaces. The possibility of gas condensation to form intercrystalline voids and cracks is eliminated as a basic mechanism because such voids and cracks are developed in vacuum melted material containing minute amounts, if any, of gaseous impurities. In a theoretical evaluation of this problem, Machlin7 concluded that void nucleation by vacancy condensation during creep-rupture is improbable but that vacancy condensation on supercritical sized voids to produce growth is probable. This investigation was begun to evaluate the suggested mechanisms for intercrystalline fracture. In particular, in order to correlate vacancy supersaturation ratios produced in creep with those determined by Bal-luffi and Seigle8 as critical for , the nucleation of voids, specimens were obtained from the same heat of brass as used by the latter authors, through the courtesy of Dr. Seigle. The experiments conducted in this investigation fall into the following categories: 1) Brass—observation of voids produced under a variety of conditions, including creep under compression, to evaluate the mechanisms of void nucleation and growth. 2) Bicrystal experiments to check the mechanism of void nucleation deduced in this investigation. 3) Morphology of intercrystalline voids produced in a variety of metals. Each set of experiments will be described and discussed separately. Experimental Techniques A special creep-rupture test rack was constructed which made it possible to apply the stress to the specimen in a controlled atmosphere of inert gas, reducing gas, or vacuum. All the creep-rupture tests on a-brass (30 pct Zn) were conducted in nitrogen under a pressure slightly above atmospheric. Either dead weight loading or constant elongation rate loading could be applied with the load measured by means of a strain gage dynamometer. In order to obtain a coarse-grained crystal structure stable at

Jan 1, 1958

By Michel T. Halbouty

The area for which oil and gas developments in South Texas are reported for 1940 in this paper covers the same counties that were included in the reports for 1938 and 1939, with the addition of LaSalle County. LaSalle County is includcd in the Laredo district of South Texas, which totals seven counties for that district. The Corpus Christi district remains the same, with nine counties. The two districts together comprise what is known as the South Texas area for this report. Continued exploration along established trends and beyond proven field limits during 1940 provided South Texas with new fields and new producing levels at a rate of discovery fairly comparable with the high records set during recent years. The wells drilled in the counties within this district (including LaSalle) numbered 1656, approximately 8 per cent below the 1801 figure of last year. However, rank wildcats totaIed 336, an increase of 17.5 per cent compared to the 286 drilled in 1939. Therefore, since new field discoveries numbered 25 in 1940 against 29 in 1939, the rate of new field discoveries in 1940, based upon rank wildcats drilled, was I/I3.4 while that of 1939 was I/9.86, which shows a decrease of about 25 per cent in the rate of new fields. The rank wildcat tests in 1940 gave the following results: 18 produced oil, 4 produced distillate with gas, 3 produced. only gas, and 3r1 were dry holes (Table 5). Of the 1320 tests drilled in already proven fields or as extensions to pro+en areas (representing a decline of 12.8 per cent from last year&apos;s total of 1515 tests), 1048 produced oil or distillate, 60 produced gas and 212 were dry holes (Table 4). Of the producers, 50 found new sands or crude-in-distillate-sands in existing fields. Among the several fields subjected to extensive development were: Colorado, Jim Hogg County; East White Point, San Patricio and Nueces County; Rincon and Sun, Starr County; Glen, Webb and Zapata Counties; Wade City and Orange Grove, Jim Wells County; Stratton and South Clara Driscoll, Nueces County, and Aransas Pass, San Patricio and Aransas Counties. The development of important crude reserves on structures formerly considered primarily distillate fields has probably been the most important phase of the year&apos;s operations in South Texas. The Rincon, Stratton, Agua Dulce, Wade City, Odem and Robston fields provided the new crude sand discoveries. At some places crude production was opened by exploratory wells that found new sand horizons; in others by flank wells that found already discovered distillate sands sufficiently low to provide crude production. Rincon, Starr County, with its multiple sands, is now believed to be one of South Texas&apos; largest crude-oil reserves. Offshore drilling showed important results during the year, including the discovery of two new submerged fields and the extension of the East White Point field into offshore Nueces County. The new marine fields are: East Flour Bluff) 76

Jan 1, 1941

By Michel T. Halbouty

The area for which oil and gas developments in South Texas are reported for 1940 in this paper covers the same counties that were included in the reports for 1938 and 1939, with the addition of LaSalle County. LaSalle County is includcd in the Laredo district of South Texas, which totals seven counties for that district. The Corpus Christi district remains the same, with nine counties. The two districts together comprise what is known as the South Texas area for this report. Continued exploration along established trends and beyond proven field limits during 1940 provided South Texas with new fields and new producing levels at a rate of discovery fairly comparable with the high records set during recent years. The wells drilled in the counties within this district (including LaSalle) numbered 1656, approximately 8 per cent below the 1801 figure of last year. However, rank wildcats totaIed 336, an increase of 17.5 per cent compared to the 286 drilled in 1939. Therefore, since new field discoveries numbered 25 in 1940 against 29 in 1939, the rate of new field discoveries in 1940, based upon rank wildcats drilled, was I/I3.4 while that of 1939 was I/9.86, which shows a decrease of about 25 per cent in the rate of new fields. The rank wildcat tests in 1940 gave the following results: 18 produced oil, 4 produced distillate with gas, 3 produced. only gas, and 3r1 were dry holes (Table 5). Of the 1320 tests drilled in already proven fields or as extensions to pro+en areas (representing a decline of 12.8 per cent from last year&apos;s total of 1515 tests), 1048 produced oil or distillate, 60 produced gas and 212 were dry holes (Table 4). Of the producers, 50 found new sands or crude-in-distillate-sands in existing fields. Among the several fields subjected to extensive development were: Colorado, Jim Hogg County; East White Point, San Patricio and Nueces County; Rincon and Sun, Starr County; Glen, Webb and Zapata Counties; Wade City and Orange Grove, Jim Wells County; Stratton and South Clara Driscoll, Nueces County, and Aransas Pass, San Patricio and Aransas Counties. The development of important crude reserves on structures formerly considered primarily distillate fields has probably been the most important phase of the year&apos;s operations in South Texas. The Rincon, Stratton, Agua Dulce, Wade City, Odem and Robston fields provided the new crude sand discoveries. At some places crude production was opened by exploratory wells that found new sand horizons; in others by flank wells that found already discovered distillate sands sufficiently low to provide crude production. Rincon, Starr County, with its multiple sands, is now believed to be one of South Texas&apos; largest crude-oil reserves. Offshore drilling showed important results during the year, including the discovery of two new submerged fields and the extension of the East White Point field into offshore Nueces County. The new marine fields are: East Flour Bluff) 76

Jan 1, 1941

By L. J. Boucher

The beneficiation process at Northampton is described and reasons are given for installing a flotation plant. The economics of running the plant, the difficulties of operation, and subsequent remedial action are discussed. CEMENT rock from a quarry operated by the Northampton plant1, 2 of the Universal Atlas Cement Co. has a relatively low average CaCO³ content. To meet specifications required for cement manufacture it was formerly necessary, over succeeding years, to add increasingly larger amounts of high-lime, low-alumina rock, which was obtained from a quarry operated by the company at a point along the New Jersey-New York state border, 79 miles from Northampton. Previous to 1940, 8 pct of total kiln feed consisted of high-lime rock. From 1940 to 1943, this figure jumped to 13 pct. Today it would be necessary to use 18 pct of this high-lime to meet current specifications. Increasing transportation costs made this an expensive operation. In addition, this high-lime rock quarry was contaminated with granite and high magnesia pockets. As there was no available high-lime rock in the Lehigh Valley, it was decided in 1936 to install a pilot plant where experimental work was done on processing local cement rock with flotation and burning the resulting product in a small kiln. This plant was in operation for six months and at the end of that period a suitable method of flotation had been established. From these studies it was also found that if the proportion of shipped-in rock rose slightly above 10 pct it became economically advisable to use the flotation process. It is the object of this paper to present briefly the operation of the flotation system at the Northampton plant. It seems advisable to comment on the raw material used in this process. The Northampton quarry lies geologically in what is known as the Jacksonburg formation of Trenton limestone.&apos; In Pennsylvania this extends in a southwesterly direction from Portland, through Nazareth, Bath, and Northampton and across the Lehigh River to Ormrod. This argillaceous limestone was formed from marine deposits laid down during the early Ordivician period when a shallow sea covered most of Pennsylvania. Carbonaceous matter in the original deposit formed graphitic carbon under later metamorphic forces. From this graphite the cement rock of the Lehigh Valley derives its dark color. Most of the graphite must be removed before lime flotation can proceed. The quartz in this rock is desirable from the chemist&apos;s point of view, as it furnishes him with a form of silica necessary in the calcining process, but its abrasive properties damage pumps and piping. Aluminum silicates of potassium, sodium, iron, and magnesium are found in the form of sericite. Cal-cite averages from 69 to 76 pct. Iron in the form of iron pyrites is also present and has no deleterious effect. Talc is present in minute quantities. The

Jan 1, 1954

By J. S. Marsh

Joseph Priestley prepared oxygen on Aug. I, 1774, and noted with great surprise "that a candle burned in this air with a remarkable brilliant flame." On Aug. 2, 1774, some ironmaker possibly began to wonder if this substance could be used to increase his rate of production; at any rate, there is no disputing the fact that the notion of using oxygen for steelmaking in concentrations greater than that available in great abundance—as air—has been in existence for years. Action was delayed by the lack of enough oxygen at a cost within reach of the steelmaker. Within the last several years enough has been available to permit large-scale tests of its use for both combustion, with which this paper is concerned, and for decarburization. The literature is now enormous and easily available; it is sufficient here to cite three items of historic importance in that all are about 25 years old and in that all are remarkably consistent as far as they go, with what is known today.1,2,3 Significance of High-temperature Heat The principal function of the open-hearth furnace is to supply sufficient high-temperature heat to melt the charge and then to increase its temperature to a range suitable for tapping, ordinarily in the neighborhood of 2900°F. That heat is required to make steel is understood by everybody; however, there seems to be some confusion now and then about the significance of high-temperature heat. Transfer of energy—and heat is energy— is always from a point of higher potential to a point of lower potential and, other things being equal, the greater the potential difference, the greater is the rate of transfer of energy. In the open hearth the flame, of course, is the high-potential source. Perhaps the most satisfactory approach is through the notion of theoretical flame temperature, which is the ratio of heat input to the heat content of the combustion products,* the former is composed mainly of heat of combustion of the fuel plus sensible heat of the fuel plus sensible heat of the combustion air. Thus, flame temperature can be increased by increasing the value of the numerator, by decreasing the value of the denominator, or both. The first method is as old as the open-hearth process and, of course, makes use of preheated air; its possibilities have been by no means exhausted. The second method can be put into effect only by changing the composition of the combustion air, since the combustion of a given quantity of fuel produces a definite quantity of product, and since the denominator includes the non-reactive fraction of the air, principally nitrogen. In other words, the denominator consists of the volume of exit gas multiplied by its heat capacity and that volume consists of carbon dioxide and water vapor as reaction

Jan 1, 1949

By J. S. Marsh

Joseph Priestley prepared oxygen on Aug. I, 1774, and noted with great surprise "that a candle burned in this air with a remarkable brilliant flame." On Aug. 2, 1774, some ironmaker possibly began to wonder if this substance could be used to increase his rate of production; at any rate, there is no disputing the fact that the notion of using oxygen for steelmaking in concentrations greater than that available in great abundance—as air—has been in existence for years. Action was delayed by the lack of enough oxygen at a cost within reach of the steelmaker. Within the last several years enough has been available to permit large-scale tests of its use for both combustion, with which this paper is concerned, and for decarburization. The literature is now enormous and easily available; it is sufficient here to cite three items of historic importance in that all are about 25 years old and in that all are remarkably consistent as far as they go, with what is known today.1,2,3 Significance of High-temperature Heat The principal function of the open-hearth furnace is to supply sufficient high-temperature heat to melt the charge and then to increase its temperature to a range suitable for tapping, ordinarily in the neighborhood of 2900°F. That heat is required to make steel is understood by everybody; however, there seems to be some confusion now and then about the significance of high-temperature heat. Transfer of energy—and heat is energy— is always from a point of higher potential to a point of lower potential and, other things being equal, the greater the potential difference, the greater is the rate of transfer of energy. In the open hearth the flame, of course, is the high-potential source. Perhaps the most satisfactory approach is through the notion of theoretical flame temperature, which is the ratio of heat input to the heat content of the combustion products,* the former is composed mainly of heat of combustion of the fuel plus sensible heat of the fuel plus sensible heat of the combustion air. Thus, flame temperature can be increased by increasing the value of the numerator, by decreasing the value of the denominator, or both. The first method is as old as the open-hearth process and, of course, makes use of preheated air; its possibilities have been by no means exhausted. The second method can be put into effect only by changing the composition of the combustion air, since the combustion of a given quantity of fuel produces a definite quantity of product, and since the denominator includes the non-reactive fraction of the air, principally nitrogen. In other words, the denominator consists of the volume of exit gas multiplied by its heat capacity and that volume consists of carbon dioxide and water vapor as reaction

Jan 1, 1949

By Louis A. Panek

THE purpose of this paper is to present a method of designing safe and economical arch structures that are to be constructed of concrete or directly of original earth materials. The experimental data used to illustrate the design method are taken from Bucky and Fentress,1,2 and the application of the ideas presented by them is extended by obtaining an additional set of curves from which arch structures may be designed. This design method is based upon the following principles of similitude: A scalar model made of the same material as that of the full sized structure will behave similarly to its prototype if the density of the model is increased in the same proportion as its linear scale is decreased. Let R represent the scale or model ratio, namely, the ratio of a prototype linear dimension to the corresponding model linear dimension. The effect of increased density may be obtained by rotating the model in a centrifuge at a speed such that the centrifugal field exerts on the model an accelerative force R times the accelerative force of gravity. Under these conditions; (I) model unit stresses are equal to corresponding prototype unit stresses, (2) the ratio of the prototype deformation at a given point to the model deformation at a similar point is equal to the scale ratio, R, and (3) the model and the prototype will behave similarly within and beyond the elastic limits of strain. According to the above relations, such models can be used to solve the following problems: I. The dimensions of the most economical safe arch structure for a given load. 2. The maximum safe roof span underground for given geologic conditions. The procedure is described briefly as follows. Tests are made by rotating in a centrifuge a number of models that repIesent a variety of prototype loads and dimensions. From the experimental data, curves are plotted to show the relations between these loads and dimensions. The curves are used to solve directly the problems stated above. Structural design is based upon the working (safe) stress of the material of construction, which is established by applying a factor of safety to the experimentally determined ultimate strength of the material. In conformity with this principle, each model is gradually loaded until failure occurs. A safety factor is then applied to the results. If a safety factor of 4 is used, a given model at failure represents a safe prototype, the linear dimensions of which are equal to one-fourth the model ratio at failure times the corresponding model dimensions. The safe model ratio is computed from the following formula: [Safe R = (rl 47r2n2r _ 7r2n2r~r~ \4/ gg in which: n = centrifuge revolutions per second at model failure; r = radius of rotation of the model in feet; g = 32.2 ft/sect.]

Jan 1, 1947