Search Documents

By Leo Dana

INTRODUCTION THE object of this paper is to discuss the factors and conditions that affect the observed values of the melting points of refractory materials and to describe practical methods for the determination of these points. While it appeared to be necessary to discuss some of the general properties of silicates and refractories, these subjects have been entered into only in so far as they relate to the melting point and its determination. Refractory materials such as fireclays, firebricks, and minerals generally, may be considered to be composed of compounds of metallic oxides, solid solutions of the oxides, the pure oxides, or mixtures of the three classes together with small amounts of a variety of chemical compounds. The oxides of silica and alumina occur most commonly in refractory materials; in combination with. these, oxides of the alkali earth, the alkali, the iron group, and the rare earth metals are frequently found.

Jan 9, 1919

By J. W. Gilbert

DuriNG the sinking of the Needmore shaft, on one of the leases of the Eagle-Picher Mining and Smelting Co north of Webb City, Missouri, a very strong flow of water was encountered at a depth of 140 ft. Because OF the speed at which the water rose in the shaft after pumping was discontinued, and in order to speed up sinking operations, a new type of shaft bar and drilling equiprnent was devised, which saved approximately one hour on each shift This bar is made of an ordinary scren type shaft bar with a common drill arm attached to the bar by clamps and welded Into place To this drill arm is attached an ordinary arm clamp with set collar below Through this clamp is attached another drill bar of ordinary length so constructed that it slides back and forth and rotates around the perimeter of the shaft on the set collar A tripod saddle with legs removed is welded to the rotating bar, which enables the drill operator to drill holes at any angle completely around the shaft and also, after an arm extension, permits the drilling of the corner holes without removal of the rig from the saddle Upon completion of the drilling of a shaft round, all that is necessary for the complete removal of the drill machine and shaft bar is to engage the hoist hook through a. ¾-in. eye provided for that purpose on top of the bar and disconnect the air and water lines from the machine, thereby making it possible to pull the whole apparatus out in one piece. At no time is it necessary to remove the machine from the saddle Screw jacks are installed on the vertical bar to further ensure the rigidity of the shaft and bar arm. The accompanying sketch illustrates the details and method of setting up.

Jan 1, 1946

By T. P. Meloy

Economic constraints require that the optimum mineral processing circuit be chosen for a given ore and then the circuit be optimized. Meloy (1983) developed a general methodology for finding the best circuit for a given ore. This analysis, however, did not specify a way to optimize the best circuit once it has been found. To optimize a given circuit, it is necessary to find the optimum set points for each unit operation in the circuit. Developed in this paper is a simple, general equation which, when applied, defines the optimum separation set point for the maximum mineral grade. This general equation, Equation (4), applies not only to simple ores, but also to complex ores containing variable and locked particles. Currently, the optimum set point can be calculated only for heavy media and cyclone circuits, because they are the only unit operations for which the necessary data has been measured.

Jan 1, 1984

By J. E. Burke, A. M. Turkalo

IN 1923 Desch¹ pointed out that the grains in a metal which is anisotropic with respect to its thermal coefficient of expansion would contract differently upon cooling, and that the stresses developed might approximate the plastic strength of the metal. More recently Boas and Honeycombe2-5 studied the behavior of several metals upon thermal cycling and observed that the stresses developed in arlisotropic metals are great enough to produce slip lines in individual grains and a roughening of the specimen surface. This phenomenon they have named "thermal fatigue." The mechanism they propose involves essentially a kneading of the grains, the deformation being alternately in compression and tension in a given grain as the temperature is changed in one direction and then the other. The present work was undertaken to investigate the possibility that an additional mechanism might operate to produce plastic deformation during thermal cycling—a "thermal ratchet" that depends upon a combination of grain boundary flow to relax the stress that develops between differently oriented grains upon raising the temperature and transcrys-talline slip to relax the oppositely directed stress which develops on lowering the temperature. Thus, thermal cycling should produce a nonreversible distortion such that certain grains will change shape differently from their neighbors with a simultaneous displacement being produced at the grain boundary. Temperature Dependence of Grain Boundary and Grain Strength The critical resolved stress for the initiation of slip in metal grains is only mildly affected by temperature." For example, in cadmium it decreases from 0.15 to about 0.05 kg per sq mm when the temperature is increased from 20° to 458°K and further temperature increase causes little further decrease. On the other hand, the work of KG1 indicates that the grain boundaries behave in a viscous fashion that can be described8 by the expression: t = BVexp(Q/RT) [1] t is the shearing stress on the boundary; B, a constant; V, the flow rate at the boundary; Q, the activation energy for grain boundary flow; R, the gas law's constant; and T, the absolute temperature. Eq 1 indicates that the stress necessary to cause a given grain boundary flow rate, V, decreases rapidly with increasing temperature. The value of the constant B is such that at sufficiently low temperature and ordinary strain rates deformation will occur preferentially by slip rather than by grain boundary flow. There is considerable evidence to indicate Consider the bicrystal shown in Fig. 1. In grain 1 the slip plane lies 45 " to the boundary while in grain 2 the slip plane is 90" to the boundary. The coefficients of expansion of the grains in a direction parallel to the length of the crystal are a1 and a, with a, > a2 for the orientations shown. The sequence of events that can occur upon heating and cooling this specimen is illustrated schematically in Fig. 2. Initially there is assumed to be no stress in the specimen (A). Upon heating, grain 1 attempts to become longer than grain 2, but is constrained by grain 2. Thus grain 1 is loaded in compression and grain 2 is loaded in tension, and a shearing stress is present across the boundary (B). As the temperature is increased, the stress will build up, and finally grain 1 will be plastically deformed by slip, since the greater stress is resolved on its slip planes. Any further heating will result in more slip and the stress will remain constant until some temperature T* is reached where the stress can be relaxed by grain boundary flow.† At this relaxation temperature (C) a step will appear between grain 1 and grain 2. Further heating above T* will cause grain 1 to become relatively longer, but no stress will appear because the grain boundary is too weak to support the stress (D). Upon cooling again, at T* (E), the grain boundary will again be able to support a shearing stress, and upon cooling further, grain 1 will be loaded in tension and grain 2 in compression (F). When the decrease in temperature below T* is sufficient to impose the critical shear stress upon the slip plane of grain 1, it will be stretched by slip.

Jan 1, 1953

By C. P. Sandberg

Notwithstanding the growing importance of this subject, no work specially devoted to it has hitherto been published. Having had to inspect during the last twenty years nearly a million tons of iron and steel rails for various countries, I have obtained experience of what rail manufacturers can practically execute, as well as of what railway engineers practically require. Bearing these two points in mind, I have from time to time published observations with a view to unite both interests,—that of the producer and that of the consumer,—and to reduce the specifications and the forms of sections to standards, or types, in order to facilitate the execution of the works and to improve the construction of permanent way. The Swedish government railways, as well as private companies owning railways in Sweden, Norway, and Denmark,.have during the time above mentioned consulted with me and intrusted to me their rail inspection. I therefore owe to these countries much of the opportunity which I have enjoyed of gaining experience and position. Next to Sweden, America is the country which has most liberally favored me with its confidence in placing these matters in my hands. Through circumstances not under my control there has been little exportation to, and less work done by Europe for, America during the last six years; but the recent revival of the rail trade has been the more gratifying to mo, seeing that almost all the importers of American rails are still specifying for the Sandberg rail sections and inspection. It is therefore with feelings of gratitude that I now beg to lay before the American Institute of Mining Engineers, and I hope, through that body, before the American railway world, the results of some experience which I have gained in the execution of work for their country, and which therefore belongs rightfully to

Jan 1, 1881

By C. P. Sandberg

INTRODUCTION. NOTWITHSTANDING the growing importance of this subject, no work specially devoted to it has hitherto been published. Having had to inspect during the last twenty years nearly a million tons of iron and steel rails for various countries, I have obtained experience of what rail manufacturers can practically execute, as well as of what railway engineers practically require. Bearing these two points in mind, I have from time to time published observations with a view to unite both interests, -that of the producer and that of the consumer,-and to reduce the specifications and the forms of sections to standards, or types, in order to facilitate the execution of the works and to improve the construction of permanent way. The Swedish government railways, as well as private companies owning railways in Sweden, Norway, and Denmark, have during the time above mentioned consulted with me and intrusted to me their rail inspection. I therefore owe to these countries much of the opportunity which I have enjoyed of gaining experience and position. Next to Sweden, America is the country which has most liberally favored me with its confidence in placing these matters in my hands. Through circumstances not under my control there has been little exportation to, and less work done by Europe for, America during the last six years ; but the recent revival of the rail trade has been the more gratifying to me, seeing that almost all the importers of American rails are still specifying for the Sandberg rail sections and inspection. It is therefore with .feelings of gratitude that I now beg to lay before the American Institute of Mining Engineers, and I hope, through that body, before the American railway world, the results of some experience which I have gained in the execution of work for their country, and which therefore belongs rightfully to

Jan 1, 1881

By Dwight H. Seely, Louis R. Records

A process for low-temperature dehydration of natural gas utilizing Joule-Thomson effect in expansion through a throttling orifice has been tested in a full-scale field installation. The results of these tests are presented in the form of performance curves from which the process may be easily evaluated. The effect of separation temperature on condensate recovery from the process is also shown. INTRODUCTION The transportation of natural gas from producing well to the consumer has always encountered the problem of hydrate prevention. This problem has become increasingly important in the past ten years due to the rapid increase in produced gas volumes, production pressures, transportation pressures and distance from producing wells to consumer. Natural gas, as normally produced from gas or gas-condensate wells, is saturated with water vapor at well-head conditions of temuerature and pressure. The solution of the hydrate problem require; but one basic process — dehydration of the gas to a water content which will result in a water dew-point below the minimum temperature to be encountered from the producing well to the point of consumption. Much of the recent development of gas and gas-condensate reserves in the Gulf Coast Area has been in locations which are accessible only by water. High well-head pressures, pipeline construction and maintenance costs and the desirability of final central gas-condensate separation facilities have stimulated the development of dehydration equipment which can be installed at each well and which will permit hydrate-free transportation of both gas and condensate in the same line to central facilities. There are four types of natural gas dehydration processes now used: 1. Adsorptive processes. 2. Absorptive processes. 3. Chemical reaction processes. 4. Refrigeration processes. The first three of these processes are indirect in that they require use of adsorbents, absorbents or reactive chemicals. These materials require regeneration and part of the total gas stream is consumed in the regenerative process. Indirect processes have a wide range of flexibility as defined by allowable operating pressure and temperature, but most are not easily adapted to automatic operation. The refrigeration process described in this paper was designed for installation at the producing well-head. It requires no regenerative cycle and with normal well-head temperatures no external source of heat. The flexibility of this process is limited only by the pressure drop which may be allowed between well-head and transportation line. THEORY There are three basic physical concepts involved in the low temperature dehydration process. These are: 1. Formation of hydrocarbon hydrates. 2. Joule-Thompson effect resulting from the expansion of gaseous mixtures through a throttling orifice. 3. The equilibrium composition characteristics of water vapor and gaseous hydrocarbon mixture.. The chemical composition and physical structure of hydrate; have been described by several investigators.3,4,5,10 Specific conditions of temperature, pressure and composition as well as the requirements for turbulence and presence of free water necessary for hydrate formation have been described by Katz.6 Natural gas hydrates, as they are found in plugged gas pipe lines, have the appearance of packed snow. The mass of these hydrates has low continuous porosity and permeability. Joule-Thomson effect. or the reduction in temperature which occurs when natural gas is throttled throusll a restrictive orifice, is the basic phenomenon which permits efficient use of refrigeration for the purpose of dehydrating natural gas. Joule-Thomson coefficients for gafeous mixture; of methane with ethane and with butane have been reported by Buder.-I~olzer, Sage and Lacey.2 Brown1 predicted temperature drops for pressure drops from enthalpy-entropy calculations. Aside from this work there were no fundamental data found which would be applicable to natural gas mixtures of varying spe-

Jan 1, 1951

By Dwight H. Seely, Louis R. Records

A process for low-temperature dehydration of natural gas utilizing Joule-Thomson effect in expansion through a throttling orifice has been tested in a full-scale field installation. The results of these tests are presented in the form of performance curves from which the process may be easily evaluated. The effect of separation temperature on condensate recovery from the process is also shown. INTRODUCTION The transportation of natural gas from producing well to the consumer has always encountered the problem of hydrate prevention. This problem has become increasingly important in the past ten years due to the rapid increase in produced gas volumes, production pressures, transportation pressures and distance from producing wells to consumer. Natural gas, as normally produced from gas or gas-condensate wells, is saturated with water vapor at well-head conditions of temuerature and pressure. The solution of the hydrate problem require; but one basic process — dehydration of the gas to a water content which will result in a water dew-point below the minimum temperature to be encountered from the producing well to the point of consumption. Much of the recent development of gas and gas-condensate reserves in the Gulf Coast Area has been in locations which are accessible only by water. High well-head pressures, pipeline construction and maintenance costs and the desirability of final central gas-condensate separation facilities have stimulated the development of dehydration equipment which can be installed at each well and which will permit hydrate-free transportation of both gas and condensate in the same line to central facilities. There are four types of natural gas dehydration processes now used: 1. Adsorptive processes. 2. Absorptive processes. 3. Chemical reaction processes. 4. Refrigeration processes. The first three of these processes are indirect in that they require use of adsorbents, absorbents or reactive chemicals. These materials require regeneration and part of the total gas stream is consumed in the regenerative process. Indirect processes have a wide range of flexibility as defined by allowable operating pressure and temperature, but most are not easily adapted to automatic operation. The refrigeration process described in this paper was designed for installation at the producing well-head. It requires no regenerative cycle and with normal well-head temperatures no external source of heat. The flexibility of this process is limited only by the pressure drop which may be allowed between well-head and transportation line. THEORY There are three basic physical concepts involved in the low temperature dehydration process. These are: 1. Formation of hydrocarbon hydrates. 2. Joule-Thompson effect resulting from the expansion of gaseous mixtures through a throttling orifice. 3. The equilibrium composition characteristics of water vapor and gaseous hydrocarbon mixture.. The chemical composition and physical structure of hydrate; have been described by several investigators.3,4,5,10 Specific conditions of temperature, pressure and composition as well as the requirements for turbulence and presence of free water necessary for hydrate formation have been described by Katz.6 Natural gas hydrates, as they are found in plugged gas pipe lines, have the appearance of packed snow. The mass of these hydrates has low continuous porosity and permeability. Joule-Thomson effect. or the reduction in temperature which occurs when natural gas is throttled throusll a restrictive orifice, is the basic phenomenon which permits efficient use of refrigeration for the purpose of dehydrating natural gas. Joule-Thomson coefficients for gafeous mixture; of methane with ethane and with butane have been reported by Buder.-I~olzer, Sage and Lacey.2 Brown1 predicted temperature drops for pressure drops from enthalpy-entropy calculations. Aside from this work there were no fundamental data found which would be applicable to natural gas mixtures of varying spe-

Jan 1, 1951

By John Wellington Finch

THE- impression which the public has of northern Canada is that it is a' vast wilderness of forests; river's, and. lakes, sparsely inhabited by. a few Indians and `containing a few, scattered trading posts of the Hudson Bay Co. This is far from the facts. The building of the Canadian Pacific Railway led to the discovery, in 1883, of the nickel deposits of Sudbury, Ont.; these are the largest known nickel deposits in the world and produce about 90 per cent. of the world's output of nickel. The building of the Temiskaming and Northern Ontario Railway north, from North Bay, to open up farming lands along Lake. Temiskaming, resulted in the discovery and development of the great silver deposits of the Cobalt area, Ontario. Since the discovery of these deposits in 1903 to Dec. 31, .1923, Cobalt has produced a total of ' 327,301,897 oz. of silver, valued at $212,668,434, and paid in. dividends $88,338,185. In 1923 the production of Cobalt amounted to 10,285,247 oz. of silver. Just south of Cobalt, in South Lorrain,. a. new silver district has recently been developed and mills have started production. These deposits are of such extent that 'a branch railroad is under construction from Cobalt to that area. Northwest of Cobalt is the Gowganda silver area which is also a producer of silver ore and is now attracting outside attention. This area is not connected by railroad.

Jan 1, 1924

By E. J. Fasiska, H. Wagenblast

The dilalion of a ivon by interslilial carbon was measured by two independent techniques —dilatometric mesurements at 719 c and X-ray measurments of the urlil cell parameters a1 room temperature after quenching. The relative expansion per increase in cavbon content by both methods is (2.9 + 0.3) x 10-3 pev at. pcl C nrzd is temperature- independent within experimental error. This corresponds to (6.3 5 0.6) cu cm per g-atom for the partial gram-atomic volume of carbon in a iron-only slightly smaller than the atomic volume for iron in the same temperature vange. THE only previous quantitative study of the dilational effect of carbon dissolved in a iron was performed in 1934 by Burns1 which, at the time, generated some discussion of possible sources of experimental error.2 For a system of such widespread importance, we felt that a new investigation was merited. Both X-ray diffraction and dilation measurements were used to determine the expansion of the a iron lattice by dissolved carbon, avoiding as much as possible any previous experimental problems and deficiencies. The dilation method at solution temperature offers not only measurements which are free of residual strain but also, in conjunction with the room-temperature X-ray measurements, a method to detect any large temperature dependence of the partial gram-atomic volume of carbon. To insure that quenching strains did not affect the room-temperature X-ray measurements, wire specimens of constant carbon content but different diameter were examined for such an effect. SPECIMEN PREPARATION The material used for both experimental techniques was "Ferrovac E" iron received in the form of 19-mm-diam rod and stated as having the following impurity contents: C, Cr, Cu, Mn, P, and V, each in the range of 10 to 50 ppm; Co, O, Mo, S, and Si, 60 to 100 ppm; W, 200 ppm; Ni, 230 ppm; N, 4 ppm. The stock material was cold-swaged to 0.71 mm diam for the Debye-Scherrer X-ray camera specimens and portions were cold-rolled from 6.3 mm diam to 0.79- and 0.25-mm sheet for X-ray diffractometer and dilation measurements. The wires were annealed in wet hydrogen for 6 hr at 840°C and 15 hr at 720°C, and then quenched into 0°C water. A chemical analysis for carbon after this treatment gave 0.0046 + 0.0014 at. pct C. Three portions of these wires were subsequently held at 719°C in three different hydrogen + methane mixtures and then quenched, resulting in carbon concentrations of 0.0283, 0.0598, and 0.1067 at. pct C by chemical analysis. After carburizing, the wires were swaged to 0.48 mm and electroplated with silver to prevent carbon loss during subsequent heat treatment. The final heat treatment consisted of holding the wires at 72 1°C for 5 min in a He-2 pct H mixture followed by quenching into 0°C brine. The wires were held at room temperature for a few minutes to remove the silver plating using a phosphoric acid-hydrogen peroxide solution, and then stored in liquid nitrogen until the measurements were made. EXPERIMENTAL TECHNIQUE A) Dilation Measurement. The dilatometer consisted of a gas-atmosphere vertical tube furnace modified so that length changes of a ribbon-shaped specimen could be measured externally. This was done by installing a gas-tight mercury seal at the top of the furnace as shown schematically in Fig. 1. The specimen (21.0 cm long, 1.27 cm wide, and 0.25 mm thick) was suspended in the center of the furnace by 3-mm-diam quartz rods with the upper one passing through the cap of the mercury seal. Above the cap, the upper quartz rod was coupled to a lever exerting a load of about 25 g (-12 lb per sq in.) on the specimen and having a 10 times mechanical magnification. The vertical position of a marker at the other end of the beam was read with a traveling microscope with a precision of 0.01 mm. The temperature gradient of the furnace was meas-

Jan 1, 1968

By G. H. Wilson

INTRODUCED in 1946 to serve a need in power-plant operation, closed-circuit TV has been used by well over 200 organizations in approximately 25 different industries. Known as industrial television, or simply ITV, it can be described as a private system wherein the television signal is restricted in distribution, usually by confinement within coaxial cable that directly connects the TV camera to one or several monitors, Figs. 1, 2. The picture is continuous and transmission is instantaneous, permitting an observer to see an operation that may be too distant, too inaccessible, or too dangerous to be viewed directly. Destructive testing or the machining of high explosives can now be conducted hundreds of feet away by personnel who still have close control through the eyes of the TV camera. It is also possible for one man to control operations formerly requiring the co-ordinated efforts of several workers. For example, at a large midwestern cement plant conveyance of limestone from primary crusher to raw mill and loading into five storage bins once necessitated the work of two men, one having little to do but prevent spilling of material by manually moving the tripper on the belt conveyor as occasion required. TV cameras mounted on the tripper now provide bin level indication to the conveyor operator at the crusher position so he is able to control the entire loading operation remotely, Fig. 3. By means of a switch, the picture from either camera is alternately available on a single viewer, or monitor, Fig. 4. Each camera is mounted on the tripper by means of a simple adjustable support and looks down into the bin, which is identified by the number of cross members on the vertical rod. Each associated power unit is located on a platform above the camera, Fig. 5. This centralized control by means of TV often has produced superior results, and in many instances saving in operating costs has been sufficient to write off equipment costs within six months to a year. Where a key portion of a process may be enclosed or otherwise inaccessible, TV again reduces the likelihood of mistakes and permits closer control by making available to the operator valuable information he might otherwise never possess. An example of this can be found at a strip mine where the coal seam lies 50 ft or more below the overburden, which is removed by a large wheel shovel. From his centrally located position the shove1 operator was unable to judge accurately to what extent the wheel buckets engaged the earth. His chief indication of efficiency was the amount of overburden on the belt conveyor as it passed his control point 75 ft from the wheel. Now, two television cameras mounted on the tip of the boom permit the operator to view the wheel from each side and provide him with a close-up view of the buckets so that he can take immediate and continuous advantage of their capacity, quickly compensating for ground irregularities and avoiding obstructions, Fig. 6. While the word television conjures up visions of highly complex and intricate apparatus such as that employed in modern TV studios and transmitting stations, the term industrial television should indicate compact, straightforward equipment. Most present-day ITV systems contain fewer than 25 tubes including camera and picture tubes. The average home television receiver alone requires at least that many tubes. Equipment like that illustrated in Fig. 1 contains only 17 tubes, of which 3 are in the camera. It can operate continuously and dependably, without protection, in any temperature from 0" to 150°F. It consumes less current than a toaster and weighs under 140 lb. Camera and monitor may be separated by 1500 to 2000 ft and by greater distance with additional amplification. This equipment is designed to withstand vibrations up to 21/16 in. and will operate successfully under more severe conditions of vibration and heat when suitable enclosures are provided. Any number of cameras may be switched to a single monitor, and any number of monitors, within reason, used simultaneously. Two types of applications in the mining industry have already been described. A third under serious consideration by several organizations will make use of ITV for remote observation of conveyor transfer points at copper concentrating plants so that evidence of belt breakdown and plugging of transfer chutes can be spotted immediately and costly overflow of material avoided. A television camera will soon be installed to view a trough conveyor near the exit of an iron-ore crusher to indicate clogging of the crusher as evidenced by reduction or absence of material on the

Jan 1, 1955

By Donald L. Katz

The equilibrium constants developed by Souders, Selheimer and Brown1' have been very useful tools in predicting vapor-liquid equilibria during the past five years. Their equilibrium constants were computed by assuming ideal solutions and recognizing the deviations of vapors from ideal gas laws. The same fundamental concepts were used by Lewis and co-workers8 for predicting vaporization phenomena by means of fugacities. The equilibrium constant is defined by equation 1: y\x =K [1] in which K = equilibrium constant, y = mol fraction of a constituent in the vapor phase, x = mol fraction of the constituent in the equilibrium liquid phase. The equilibrium constants are a function of temperature and pressure and might be considered as replacing the ratio of the vapor pressure to the total pressure of Raoult's law. They may be used to compute the vapor or saturation pressure of a liquid or the dew point of a vapor for any pressure or temperature from the analysis of the mixture much as Raoult's law is used. Likewise, the quantity of a mixture that will vaporize at any equilibrium temperature and pressure and the composition of the vapor and liquid may be calculated. The purpose of this paper is to review the available equilibrium data of interest in petroleum production, to discuss the auxiliary physical properties of the hydrocarbons, and to present typical uses of the equilibrium constants. The particular applications chosen are the computation of the results of stage separation of crude oil and natural gas, the calcula: tion of a pressure-volume curve of a crude oil-natural gas mixture, and information gleaned from a consideration of reservoir equilibria.

Jan 1, 1938

By A. J. Strauss

The solubilily of lead in PbS as a funclion of lemperature has been investigated by means of Hall coej'icient (RH) measurentents OIL samples prepared by annealing and quenching Bridgman-grourz single crystals, which contain excess lead incorporated during /heir growth from the mell. For sufficiently long annealing times and sufficiently rapid quench rules, the samples obtained consist of n-lybe PbS snturated with In the semiconducting compounds PbS, PbSe, and PbTe, the point defects associated with the presence of lead in excess of the stoichio metric composition are shallow donors. The defects associated with the presence of excess nonmetal are shallow acceptors. lead at the annealing teuiperatiire, together luilh a dispersed second phase of lead microprecipitates. Due to the retrograde solubility of lead, the measured free carrier concentration (n = l/eR77) decreases with decreasing annealing tewperature (T) from- 2.4 X 10 em-3 for 1l85OK to 1.3 X 1018 cm-3 for 623°K. The dala are well-represented by the equation n =(1.08 x 102) exp[ - (0.37 ev.)/kT] cm-3 For most undoped samples of these compounds, the carrier concentration at room temperature and below is determined primarily by the stoichiometry, since the concentration of either excess lead or excess non-metal is large compared to the concentrations of intrinsic carriers and electrically active impurities. Therefore the dependence of composition in temperature and partial pressure can be investigated by means of Hall coefficient measurements, even though the deviations from stoichiometry do not exceed 0.03 at. Pct

Jan 1, 1968

By D. E. Wolfson, D. A. Reynolds, F. W. Smith

IN 1948 the U. S. Bureau of Mines began a three-phase program to evaluate the extent and quality of U. S. coking coal: 1) a factual appraisal of known recoverable reserves in beds of mineable thickness, 2) a study of preparation characteristics, and 3) a study of carbonization properties. A previous paper presented the methods used in assessing reserves.' Although this investigation is only partly completed, data on coking properties of the Pittsburgh district coals are now available. The results are presented in this article. When coals are selected for manufacture of metallurgical coke more factors must be considered than for any other major use, as no basic industry requires coal of such high quality and uniformity. This is particularly true in the Pittsburgh district, where blast furnace practice is based on use of cokes from high quality coals. Although it is true that inferior coals are carbonized in other industrial areas, both here and abroad, the Pittsburgh coals are the best economically obtainable in the required tonnages, even though they are not the most desirable for metallurgical use. In the general evaluation of suitability of coals for coke making, particular attention is given to: 1) reserve, 2) ash and sulfur content, 3) inherent properties of forming strong, well fused coke, 4) expanding characteristics, and 5) blending properties. Items 1 and 2 are covered in detail in the first two phases of the survey, and coking behavior is considered in items 3 through 5. Problems is Coal Evaluation: Although not all coal beds of immediate or potential use to the coking industry in the Pittsburgh area have been tested for their coking properties, enough tests have been made to permit certain generalized statements. Virtually all the coals that will be used in this district are from the Appalachian region, and except for high oxygen coals from outcrops or stripping operations, they are coking coals. Hence the evaluation problem is not so much that of distinguishing between coking and noncoking coals as attempting to measure quantitatively differences in the coking and expanding properties of the better coking coals. Quantitative differentiation between good coking coals, is complex, since differences in their coking abilities are frequently of about the same magnitude as the precision of the test. Small-scale tests are generally unsuitable for measuring these slight differences, and there has been gradual acceptance of pilot-scale tests. Test Methods Employed: All the data reported here were obtained in two units known as the Bureau of Mines-American Gas Association (BM-AGA) carbonization apparatus and the sole-heated expansion oven. The BM-AGA unit, which consists essentially of a cylindrical steel retort about 18 in. diam and 26 in. high, carbonizes enough coal (180 lb) to allow evaluation of the coke by standard methods of the American Society for Testing Materials. The BM-AGA carbonization procedure and methods of testing the gas, liquid, and solid products have been described.' Expanding characteristics of the coals were determined in the sole-heated expansion oven," wherein the coal charge, heated from the bottom only, is carbonized under a constant applied force and the linear expansion or contraction is measured. Although results in this oven have never been quantitatively correlated with the expansion behavior of coals in conventional slot ovens, they are useful in assessing expansion behavior. In this report discussion will be confined to results obtained from these pilot-scale units, although the following data are available for most coals: proximate and ultimate analyses, free swelling index, agglutinating value, and plasticity. Sources of Coals Tested: In selection of coals for coke manufacture, economic considerations are as important as quality, and each coke plant balances these two factors to meet requirements of the most satisfactory coke at lowest price. Although these economic factors may in some instances outbalance small differences in coke quality, they are usually specific to each coke plant and cannot be given in any general statement. Recognizing that coal and plant operating costs are beyond the scope of the survey, the USBM evaluates the coking quality of various coals without regard to their competitive economic status. For the purpose of this article, coals of interest to the Pittsburgh district are arbitrarily defined as

Jan 1, 1958

By Robert H. Richards

If one holds up a prism, or wedge of glass, with narrow angle, say l° to 2O, and compares the transmitted image with the image seen above or below the prism, the former will be found to be thrown to one side by an amount varying with the angle of the wedge. Speaking of the two rays as the direct ray and the bent ray, we may say, that when the bisecting plane of the prism is at right angles to the line of sight, the angle between the direct ray and the bent ray will be constant for any given prism. If now we place a prism or wedge of glass in such a position that it half-covers the objective of a telescope, we shall obtain on looking through it two images of every object seen—one image by the direct ray, which comes through the unaovered half of the objective, the other which comes through the prism, and is the image by the bent ray. The angle of divergence of these two raps will be constant and unalterable, whether the telescope is directed to a near object, with its eye-piece at increased distance from its objective, or upon a ' distant object, with eye-piece nearer to the objective. That is to say, if the " throw " or apparent dislocation of the image is one foot in one hundred feet it will be two feet in two hundred, ten feet in a thousand, and so on. The usual form of stadia-telescope has at the focal point of the objective two spider-lines, placed at a definite distance apart and intended, let us say, to represent a throw of one foot in one hundred feet. But as the distance between lines remains the same, while the distance from the objective to the webs diflers with every variation in the distance of observed objects, it follows that the angle between the lines of sight which these two spider-lines define cannot be con stant, but must vary with every increase or decrease of distance be tween the instrument and the object viewed. If in Fig. 1 we represent three positions of the spider-lines by W1, W2, W3, and three objects corresponding to those positions by 01, O2, 0, at near, medium and distant positions, we see at

Jan 1, 1892

By J. Lohrenz, C. R. Clark, B. G. Bray

Procedures to calculate the viscosities of in situ reservoir gases and liquids from their composition have been developed and evaluated. Given a composition expressed in methane through heptanes-plus, hydrogen sulfide, nitrogen and carbon dioxide together with the molecular weight and specific gravity of the heptanes-plus fraction, the procedures are capable of calculating the viscosity of the gas or liquid at the desired temperature and pressure. The procedure for reservoir liquids was developed using the residual viscosity concept and the theory of corresponding states, and was evaluated by comparing experimental and calculated results for 260 different reservoir oils ranging from black to highly volatile. The average absolute deviation was 16 per cent. This is the first known procedure for calculating the viscosity of reservoir liquids from their compositions as normally available, i.e., including the heptanes-plus fraction. The procedure for reservoir gases uses a sequence of previously published correlations. Evaluation of the procedure was accomplished by comparison of 300 calculated and experimental viscosities for high-pressure gar mixtures in the literature. The average absolute deviation was 4 per cent. The calculations are useful for (I) determining viscosities in compositional material balance computations and (2) predicting the viscosity decrease which occurs when gases, LPG, or carbon dioxide dissolve in reservoir oils. INTRODUCTION Methods to predict viscosities of reservoir fluids from the normally available field-measured variables have been presented. Beal,1 Standing,2 and Chew and Connally3 orrelated oil viscosities with temperature, pressure, oil gravity and gas-oil ratio. Carr, Kobayashi, and Burrows4 and Katz et al.5 have presented correlations for reservoir gas viscosities as a function of temperature, pressure and gas gravity. Lie all intensive physical properties, viscosity is completely described by the following function: Eq. 1 simply states that viscosity is a function of pressure, temperature and composition. These previous correlations1- hay be viewed as modifications of Eq. 1, wherein one assumes more simple functions may be used. The assumptions are practical, because the composition is frequently not known. Further, the assumptions are sufficiently valid so that these correlations are frequently used for reservoir engineering computations. In compositional material balance"' computations, the compositions of the reservoir gases and oils are known. The calculation of the viscosities of these fluids using this composition information is required for a true and complete compositional material balance. For reservoir gases, Carr, Kobayashi and Burrows4 have presented a suitable compositional correlation. For reservoir oils, no correlation is available, and data from reservoir fluid analyses have been used7-9 for compositional material balance calculations.* From a theoretical point of view, this is entirely invalid. The reservoir fluid analysis, whether flash, differential, or other process, does not duplicate the compositions which occur during the actual reservoir depletion process, therefore the viscosities measured during reservoir fluid analysis are not those which occur in the reservoir. From a practical point of view, the "error" of using viscosities from reservoir fluid analysis is of varying and unknown significance. One can say qualitatively that the error is greatest where compositional effects are greatest, i.e., for volatile oil and gas condensate reservoirs and pressure maintenance operations. The first requirement to obtain a quantitative estimate of the significance of the error is to develop a reliable compositional correlation for the viscmities of reservoir oils. No such correlation has been available. Consistent with this requirement, the objective of this study was to develop a procedure to predict the viscosity of reservoir fluids from their compositions. Normally, the compositions of reservoir fluids are available expressed as mole fractions of hydrogen sulfide, nitrogen, carbon dioxide and the hydrocarbons methane through the heptane-plus fraction, with the average molecular weight and specific gravity of the latter. The final correlation was to use the composition in this form. While the more challenging objective of the study was the development of a correlation for the viscosities of reservoir oils, the viscosities of reservoir gases were also studied. The end result of the study was a procedure to calculate the viscosities of reservoir gases and liquids suitable

Jan 1, 1965

By T. W. Smoot

Bentonites are composed chiefly of montmorillonites which are clay minerals generally distinguished from other clay minerals by their surface activity and extremely fine particle sizes. The uses of bentonite are many and varied, depending principally on one or more of the following characteristics: 1) Thixotropy, 2) Dispersion, 3) Plasticity, 4) Swelling, 5) Surface area, activity, ab- and adsorbtive properties. Some of the major uses of bentonite are briefly reviewed as are the mineralogical and physical properties. The uses of X-ray diffraction, differential thermal analysis and other tests for physical properties are reviewed as to their uses in evaluation. In the past 40 years, the industrial uses of bentonite have grown to include many applications. The physical and chemical properties of bentonites are such that they can be used as catalysts, adsorbants, plasticizers, binders, drilling muds, and pelletizers. Not all bentonites, however, can be used for all of these purposes and some are probably of little or no value for any use. The purpose of this paper is to briefly review the mineralogical, physical, and chemical characteristics and variations of bentonites. The determination of these characteristics and their uses in industry are also reviewed so that these determinations can be used as guides for evaluation. DEFINITION OF BENTONITE The word bentonite, as used in this paper, refers to a clay material, usually (but not necessarily) the result of the in-place-weathering of volcanic ash. Its mineralogical composition is dominated by the clay mineral montmorillonite and generally carries other clay minerals and silica minerals as the major 'impurities'. For this discussion, such a definition is justified since most of the economic uses of bentonite~ depend upon the physical and chemical characteristics of the montmorillonite minerals involved. The terms montmorillonite and bentonite have been used almost interchangeably in industry although the latter is much more commonly used. Therefore, where montmorillonite is discussed, it should be understood that the major feature of a bentonite is the subject. STRUCTIJRE OF MONTMORILLONlTE The economic importance of bentonites is generally based on one or more of the following characteristics of montmorillonite: 1) high-thixotropy and easy dispersion in water, 2) high-plasticity, 3) swelling properties, 4) large surface area/unit mass, 5) high surface activity, and 6) adsorptive properties. To understand these properties, an appreciation of the structural scheme of montmorillonite is helpful. Montmorillonite IS one of the three-layer clay minerals composed essentially of hydrous aluminum silicates. The essential building blocks of these layered silicate:; are: 1) silica tetrahedron composed of a silicon atom surrounded by four oxygen atoms, and 2) aluminun (iron, magnesium, etc.) octahedral unit that, ideally, has one of these atoms surrounded by six hydroxal units. Fig. 1 is a diagrammatic sketch of the montmorillonite structure. In the montmorillonite structure, the tetrahedron are pointed inward and attached to the octahedral units so that the O= atoms replace the hydroxal units where they are bonded; hence two-thirds of the hydroxal units

Jan 1, 1962

By Anthony F. Lucas

Certain geological indications at Glady's station, four miles south of Beaumont, on the Sabine and East Texas railway (a branch of the Southern Pacific) induced me to undertake a thorough test of that locality by means of a well. I had been making reconnoissances for nearly two years in that part of Texas, before deciding upon this supreme effort. Three previous attempts had been made in the same place: one in 1894 by Messrs. Sharp & Co.; one in 1896 by Mr. J. Looney; and one in 1898 by Messrs. Savage Bros. They had all failed to pass though the immense thickness (500 ft.) of quicksand which underlies the surface soil, clay, etc. At first, I employed the system of boring which I had previously used in the Louisiana salt-deposits.* But I soon found that this method was inadequate, without modification, to deal with the quicksand. Accordingly, I adopted the use of large and heavy castings, and pipes of 12, 10, 8, 6 and 4 in. diameter, successively telescoped one into the other. Boring was begun by Messrs. Hamill Bros., of Corsicana, contractors, about the middle of October, 1900; and on January 10,1901, after many difficulties, a layer of rock containing marine shells was reached, at the depth of 1160 ft. For 150 ft. immediately above, the drill had passed through layers of sandstone and concretions of limestone. At this time there was about 600 ft. of 4-in. pipe, weighing at least 6 tons, in the well; and this, together with the next (6-in.) casing above, was filled with water. When the rock was penetrated the well " blew out," lifting the whole of the 4in. pipe. Mr. Hamill was on the top of the 60-ft. derrick when

Jan 1, 1902

By O. Chanute

all of' level atid grade curve excepting Nos. 897, 898, 899, and 900, because of the impossibility of grouping them in the same nlonner, no two Iraving the chemical composition and physical prnprtiw as tho only v:iriubles. Phosphorus ~tnits have been taken to show the relatia h:wdnes. Of these 16 groups, 10 decidedly indicate slower wear firr tile harder rail. Of the remaining 6 groups, three (groups 2, 9, and 15) come well within the limits of error (.25 pound per yard) inherent in the palculation of the data as pointed out by Dr. Dndley; they catrnot, therefore, be considered tls exceptions. Group 2 and 15 arc but little outside of the limita of error. Rail 923 of group 9 is obviously abnornlal. This is probahly due to its being overheated, which the chemical analysis shows might easily be the case, and which the physical tc~ts and its low specific gravity tend to c-nfirm. We inry say, then, thnt 13 of these 16 groups fairly indicate, if they do not definitely point out, th:kt, under the same condition% tbe harder rail gives the slower wear. Of course, these comparisons are too few to enable us to arrive at positive ~?o-nclusions; but indications thus obtained are, I believe, fir more vsluitblc and tresttvc~rthy than those fhzt averages rvottld give us, mnde up from any ~lumhr of rails under intloy difi~rcal, conditions. Finally, it, seems to me, that the conclusions arrived at earlier in my remarks, together with, and confirmed by the last, show strong evidence that, under the same conditions, the harder rail will givc the slower wear. 0. C~~anute, New York CITY: We are very much shlipl, 1 ant sure, to Mr. Sandberg for his paper upn " Rail Ryaifications and Rail Inspertion in Europe." We have in thp United States bithhrto Been inspecting mils sonlewl~at haphazard, and we ore glad to gtbt tfie results of Mr. Sandberg's long experience. We recognize that he was an)ong the first, if not the very firwt, to iipply mare rittional and scientific rules to the designing of irou rails., niora recently, to adapt tlitve rules to the clesigtting of steel I':I~]R, to conform to the oapaljilities and rqniretnento of this new n1:ttcrial. Although we have generally adopted, in this country, sectinns for hteel rails which marly of our railway men think even bottar than those of Mr. Snlldlmrg, he is neverthelees the Ieat3er in foot.iito11~ we have followed ever since it has been est~blished

Jan 1, 1881

By G. R. Wilms

A study has been made of the structural changes in polycrystalline high purity aluminum during the tertiary stage of creep under conditions of constant tensile load. It appears that there is no basic modification in the particular mechanism of deformation that characterized the preceding secondary stage of creep, but that the changes in crystalline structure produced during the tertiary stage are only a consequence and not a cause of the accelerated strain. Intercrystalline fissures were observed on entry into the tertiary stage, and these might supplement the accelerated rate of strain owing to local stress concentrations. There is evidence that the formation of these fissures may be associated with the presence of surface imperfections, and it is suggested that a more generalized treatment of the results may explain certain creep characteristics of commercial alloys. IN previous work'-4 a study was made of the changes produced when specimens of annealed aluminum were deformed at various temperatures and rates of strain, especially under conditions leading to creep under constant tensile load. It was shown that, as the temperature was increased or as the rate of strain was decreased, elements of the substructure produced within the grains became coarser, and with the strain rate constant at a given temperature, their size tended to an equilibrium value. The preliminary process of the breaking down of the grains into a substructure was identified with primary creep.' The subsequent equilibrium, condition was associated with secondary creep. The question then arose whether the tertiary stage corresponded to any further significant change in the substructure. The question is also of interest in view of the opinion, expressed for instance by Andrade,5 that the tertiary stage is merely an accelerated rate of strain due to the reduced area of section of a specimen under continuous tensile load, and the other opinion, as suggested by the observation by Sully, Cale, and Willoughby6 of a tertiary stage in com-pressive loading, that this third stage is a real effect in its own right. The object of this paper is to record some observations on the tertiary stage of high purity aluminum. Experimental Procedure The material was aluminum of 99.98 pct purity as previously used. The specimens had a rectangular section of l/8 x l/2 in., and extensions were measured over a 1 in. gage length. After machining to shape, the specimens were annealed to give a standard grain size of 0.2 mm and then electropolished. The general procedure involved metallographic and X-ray diffraction examination at progressive stages of elongation (marked by arrows on the curves shown in Figs. 1 and 2), the specimen being extended to fracture under constant load at a given temperature. The X-ray tests were made by the back-reflection method from a stationary specimen, using CoK radiation. The longer edge of the micrographs in the paper corresponds to the direction of applied stress. Results The previous work showed that, in the secondary stage of creep in aluminum, three basic types of structure could be developed according to the temperature and rate of strain. These were: 1—slip, which predominated at the lower temperatures and higher rates of strain and produced the finest and least perfect substructure; 2—cell structure, which superseded slip as the temperature was raised and the rate of strain decreased and which was characterized by a coarser and more perfect structure and an absence of slip lines; and 3—a stage termed "boundary microflow," which predominated at still higher temperatures and lower rates of strain when the cell size had increased and become comparable

Jan 1, 1955