Search Documents

By I. L. Box

IN planning retreatment of tailings, the material to be retreated should be thoroughly investigated, tak- ing into consideration the total tonnage, the blende content, the specific gravity of the different particles, and the grinding necessary to liberate the mineral. The tailing pile is surveyed by making a closed trav-erse around the outer edges, locating the stations at points from which a considerable portion of the pile is visible. From each of these points the pile is sur-veyed by stadia and a contour map made. The yardage is then calculated from the contour interval and the area inclosed by the contours obtained with a planim-eter. A party of three men can survey an average tailing pile in one and one-half, days. In calculating tonnage it is assumed that 22 cu. ft. of tailing in place equal one ton. Sampling is done by the use of an auger with casing to prevent the hole from caving. These holes may be bored 12 to 15 ft. deep by hand, but to penetrate the entire pile some kind of power is applied to drive the casing and raise or lower the auger. The latter method is more expensive but the increased cost is more than compensated for by the value of the information obtained.

Jan 7, 1928

By W. C. Browning

The influence of the hydroxyl factor is more damaging to formations penetrated and causes greater consumption of drilling mud additives than previously realized. This hydroxyl effect on clays is essentially independent of the cations present in the drilling fluid and thus differs from the base exchange reactions that have preoccupied mud chemistry with sodium and calcium bentonite concepts for nearly two decades. The new organic polyelectrolyte-con-ditioned muds haw made it possible to use materials other than sodium hydroxide to maintain the alkalinity of such muds. The properties of silicates, as indicated by their dissociation characteristics and buffering action, are such that they can control he pH and alkalinity of drilling muds at the desired level and, at the same time, minimize undesirable hydroxyl effects associated with sodium hydroxide. This use of silicate compounds is different and distinct from prior applications of silicates as deflocculants or shale preservers. Laboratory and field data presented in this report show that silicate compositions can be utilized to adjust the alkalinity of drilling muds and, at the same time, minimize hydmxyl-promoted clay cleavage. INTRODUCTION Studies for improving the efficiency of rotary drilling techniques must consider the chemistry of drilling fluids and of the formations being penetrated. The chemical aspects of drilling must be studied in conjunction with and in relation to the mechanical factors if, for example, penetration rates are to be optimized. Drilling fluid technology has been largely influenced by chemical reactions of the montmorillonite (bentonite) clay minerals. Most of the literature of mud chemistry concerns the properties of bentonite. Clays of the kaolin or illite type, which are nonswelling, are not generally regarded as sources of drilling mud problems. If these nonswelling shale clays are considered, they are commonly regarded as inert solids. Particularly noteworthy is the fact that the relation of surface and colloid chemistry to massive shale bodies has received only scant attention from drilling technologists. Clay studies reported in the drilling mud literature have dealt, for the most part, with the properties of clays in a finely divided state, and often in very dilute suspensions. Yet frequently during drilling, shale problems not related to the rheology of clay suspensions develop in massive non-bentonitic shale sections of zero or near zero permeability. This paper is concerned with surface chemical reactions that can influence the behavior of these non-bentonite clay masses in such a manner as to adversely affect drilling operations. Browning and Perricone1,2 have pointed out that some of the most troublesome shales to drill, such as the Atoka, contain no montmorillonites. They also pointed out that mud problems can frequently be mitigated by reduction of clay cleavage achieved by using drilling fluids with a minimum of available hydroxyl ions. If pronounced clay cleavage occurs during drilling, the borehole may soften, increasing the possibility of sloughing. In addition, the resulting increased incorporation of high-surface-area clay solids into the mud system can reduce penetration rates and necessitate greater chemical treatment. This increase of shale, of colloidal or near-colloidal dimensions, into the drilling mud is due to clay aggregate cleavage and not to base exchange or swelling reactions, such as occur with bentonites. Searle and Grimshaw3 point out the difference between cleavage or slaking reactions of nonswelling clays (such as illite and kaolinite) and the swelling of bentonite. They further state that the speed of slaking is increased in alkaline water. Eitel1 cites Salmang and Becker, who recognized that clay surface reactions impart plasticity and workability to clay masses. Their results clearly show that all liquids which contain hydroxyl groups in their molecules favor the workability of clays. The ancient technique of aging clays in the moist condition to increase their "workability" is evidence that these clay cleavage phenomena are of considerable importance. The same hydration cleavage that occurs during the aging of nonswelling clays for ceramic use also acts to break up cuttings and soften the borehole during drilling operations. The mechanism of cleavage of the crystalline aggregates of illitic, kaolinitic and other nonswelling clays; and the chemical means of controlling this cleavage are therefore of considerable significance to the drilling mud chemistry. Inasmuch as there is little reference in the drilling mud literature to the cleavage reactions of nonswelling clays, the structure of these clays and certain properties that relate to the mechanism of clay cleavage will be reviewed briefly. STRUCTURE OF NONSWELLING CLAYS Clays such as kaolinite, illite and montmorillonite are compmed of alternate layers of (1) silicon-oxygen tetra-

Jan 1, 1965

By J. B. Cohen

EARLY investigators1-4 reported that additions of beryllium to silver caused embrittlement. The in-termetallic phases which are now known to exist5,' were not known at the time. Solidification appeared to occur by a simple eutectic reation.4,7 (The primary beryllium-rich phase appeared globular, when the liquidus temperature was near the melting point of pure beryllium, and angular when the liquidus was much lower; in discussion of Sloman's work,4 it was suggested that this difference was due to an intermetallic compound which was not revealed by the polishing technique.) In the investigation reported here, it was found that if the compounds now known to exist were avoided, certain beryllium-silver alloys containing large amounts of the primary beryllium phase possessed sufficient ductility to be cold formed. Alloys containing 14 and 20 at. pct Ag were prepared from vacuum-cast beryllium containing 1.0 to 1.2 pct impurities and silver, 99.99+ pct pure. The elements were melted together by induction in beryllia or alumina crucibles under argon at less than 1 atm pressure. The cooling rate was adjusted by regulating the temperature of the melt and by reducing the power to zero without stopping the water flow in the induction coils, which were in contact with the crucible. Ingots were about 0.75 in. in diam with a grain size of 0.12 to 0.25 in. Microscopic investigation of transverse or longitudinal sections of an ingot cast from a temperature well above its melting point showed that, in general, the compounds did not form, presumably because of rapid cooling; the alloys consisted of beryllium-rich particles in a silver-rich matrix as shown in Fig. 1. A eutectic structure was not observed, probably .due to the low beryllium concentration of the eutectic composition and eutectic divorcement. Within a given grain, the small globules of the primary phase were all oriented in the same direction, as indicated by examination under polarized light; the orientation varied from grain to grain. This suggested that the globules were branches of the same dendrites. If cooling was too slow, a third constituent was observed in the microstructure; because it formed around the primary beryllium-rich globules it was Fig. 1—Ag-Be alloy, 18.6 at. pct Ag, as-cast. Bright field illumination. Etched with an aqueous solution of NH,OH and H2O2. X500. Reduced approximately 21 pct for reproduction. probably the 6 compound. A thin ring around an ingot often contained this constituent. When this compound was present in large quantities, or the silver segregated so that large regions occurred with the beryllium-rich globules in contact, sections from the ingot were brittle. When the compound was initially absent, it was possible to carry out reductions in thickness of 50 pct by cold rolling with only limited edge cracking; failure did not occur until reductions of 80 pct. A typical cross section after cold rolling is shown in Fig. 2. After simple bend tests, microcracks were found; these apparently were difficult to propagate in the two-phase structure, as the specimens continued to behave in a ductile manner after the cracks appeared. Similar cracks would probably be closed during rolling. It is apparent in Fig. 2 however, that the primary beryllium particles undergo extensive plastic deformation. Hardness values of the alloys indicated that some work-hardening occurred during cold working. Fig. 2—Ag-Be alloy, 18.6 at. pct Ag, reduced 83 pct in thickness by cold rolling. Bright field illumination. Etched with an aqueous solution of NH,OH and H2O2. X500. Reduced approximately 21 pct for reproduction.

Jan 1, 1961

By R. T. Murrill

BLOCK-SIGNAL and dispatching systems have been in use on surface railways for years, but only recently have they been applied to underground mining conditions. Formerly, all ore was moved underground by hand tramming; the surface openings were numerous and fairly close to the ore being mined. As the tramming distances increased, animals were brought into service. Then came the locomotive, and since its introduction, haulage lines have gradually been reduced to fewer levels and to fewer surface openings until more than 20,000 tons are being handled daily on one level in some of the larger mines. Under the, se conditions many trains must use the same-tracks, and signal systems have become necessary. In some cases it has been found more advantageous to use train dispatchers than to install signal devices. The dispatcher may be simply a flagman at a busy point or he may have mechanical signals to operate at more distant points. At the inspiration mine, Inspira-tion, Ariz., the station is equipped with a switch-con-trol board, whereby the dispatcher throws electrically all track switches in a certain block, which gives him complete control over all trains passing through that block. In a few cases, dispatcher stations are established in connection with a signal system.

Jan 2, 1922

By GEORGE O. SUMAN

IN THE operation of oil properties there are various difficulties with pumping wells which can often be overcome or greatly lessened if sufficient attention is, directed towards pump and tubing problems. The difficulties referred to are the wearing out of pumps, sanding up of pumps, and the sanding up of the hole. As the perforations in the oil strings are large and the oil and sand loose and unconsolidated considerable trouble is often encountered in pumping wells due to the ease with which' the sand can come into the holes. DETERMINING FLUID LEVEL In determining the proper depth at which to tube a well it is essential to first find out something about the behavior of the fluid in 'the hole: Facts in regard to this natter can be obtained by finding the fluid level on pulling the tubing, by making a pumping test on the well tubed to various depths, and by bailing tests during cleaning out work. In ordinary oil field operations it is customary to take the fluid level at the time of pulling the tubing. This 'can only be done when the pump is not sanded up. There are two methods used in obtaining the fluid level. One method is to note where the outside of the tubing starts, to be covered with fluid when pulling the

Jan 1, 1925

THERE is probably no phase of basic open-hearth steelmaking that is more of an art and less of a science than mold and pouring practice. It varies widely from plant to plant; consequently it is obviously impossible to set down in detail in this chapter the many ramifications of practice that are now used. The discussion that follows therefore attempts only to give an outline of the more common methods, with examples sufficient to indicate some of the variations in procedure, and to emphasize a few of the many underlying problems that face the open-hearth operator at the pouring platform. MOLD DESIGN Ingot molds are hollow castings of considerable wall thickness. Despite this, non-uniformity in wall thickness should be strictly avoided to prevent the setting up of unnecessary stresses. Molds are cast in various forms, sizes, and shapes depending on the type of steel, and on whether the ingot is to be withdrawn from the mold or the mold from the ingot. The selection of ingot-mold material, which is usually cupola or blast-furnace iron containing approximately 3.5 per cent carbon, 1 per cent silicon, 0.9 per cent manganese, 0.2 per cent phosphorus, and 0.07 per cent sulphur, is governed by numerous considerations that affect mold life. (1) Factors in addition to wall thickness that should be given primary consideration at the foundry are casting skin, shrinkage stresses, and casting temperature. Factors in Mold Design. In use, mold thickness is of greatest importance, for it must be heavy enough to freeze the molten metal rising in the mold and to reduce the temperature of the steel below that of the melting point of cast iron to prevent the inner surface of the mold from melting, which would result in the welding of the ingot to the mold. The skin of an ingot, which solidities immediately upon contact with the relatively cold walls of the mold, must soon become thick enough to contract on the fluid mass and pull away slightly from the sides of the mold. The separation of the ingot from the mold depends entirely on the heat taken up by the mold from the steel.

Jan 1, 1944

By E. J. Schmitz

This novel safety-lamp, which was first introduced in some of the German coal-mines in 1882, at once attracted general attention in the coal-districts of Europe. Objections which arose during the early stages of its use at the mines have gradually died away with the increase of experience in handling the lamp 011 the part of the miners, and the continual efforts to perfect it on the part of its inventors. Wolf's lamp has rapidly surpassed all its rivals, and has already a greater distribution on the Continent than any one of its older sisters. In the course of two and a half years, the manufacturers have sold 25,000 of the lamps, besides remodelling several thousand rapeseed-oil lamps. This great success, which of itself speaks loudly enough as to the superiority of the Wolf benzine-lamp, is corroborated by both official and private reports, which all agree in pronouncing this lamp the best yet brought forward. It was described in a paper by Mr. Eugene B. Wilson, read at the Chicago meeting of the Institute, in May, 1881,* in which its salient merits were briefly but clearly indicated. Every previous improvement of the original Davy lamp has been directed to one or more of the following main points: 1. Light of greater and more uniform intensity. 2. Freedom from smoke or soot, which clogs the gauze and other parts of the lamp. 3. A greater safety and sensitiveness in the presence of firedamp. 4. An illuminating material which, satisfying the foregoing conditions, should be also cheap. 5. A lock which could not be opened in the mine by the miner. 6. An arrangement for lighting without opening the lamp. 7. An arrangement for changing the size of the flame in the closed lamp, to supersede the picker, the danger from which is explained in Mr. Wilson's paper, already cited. It may safely be said that wolf's lamp was the first to secure all these objects. The adoption of benzine instead of rapeseed-oil (previonsly the best illuminant) has completely satisfied conditions 1, 2, 3, and 4. Benzine gives a much clearer, stronger, and more uni-

Jan 1, 1886

By William Newnam

LEAD mining has been carried on in several localities of the Province of Ontario in a desultory fashion for the past 60 years, but up to 1916 the results have not been of much commercial importance. The most ambitious attempt was made by an English company which built a lead smelter at Kingston, Ont., in, 1880 to treat the- concentrates from the . Frontenac mines. After 2 years' operation, the -mines and smelter were abandoned. Up to the present there has not been a sufficient tonnage of concentrates to support an efficient blast-furnace plant and as most of the small properties could not stand the heavy freight and duty charges into the United States, development work has not been carried on in a, systematic manner. As a result the industry has languished. At, Galetta, in southeastern Ontario, considerable prospecting and development work has been carried on in the last few years and very promising deposits of galena have been found in the Chats Island group by the James Robertson Co., Ltd., of Montreal. The chief deposit is that of the Galetta or Kingdon lead mine, located on Chats Island in. the Ottawa River about 5 miles east of the town of Arnprior. The rocks' in the vicinity of -the mines consist of an interbedded series of crystalline limestone and biotite gneisses of pre-Cambrian age. This part of the Ottawa River' basin has been severely faulted and the overlying Paleozoic limestones may be seen in normal fault contact with the pre-Cambrian. The vein filling is of a very well-marked fault fissure type and although the amount of displacement is not determined at this point, similar faults to the east show a displacement of from 1,500 to 1,800 ft. which would indicate mineralized fault fissures of considerable depth. The ore occurs in a highly crystalline calcite with some barite and fluorite, and the galena occurs more or less richly disseminated in clusters and crystal aggregates. In some cases these masses weigh several hundred pounds. Small amounts of sphalerite are occasionally encountered.

Jan 4, 1917

By A. E. Bellis

There is a wide difference of opinion among rifle experts in the matter of barrel steel, and the relative importance to the life of the barrel of the steel's composition, heat treatment, structure, and physical properties. In order to promote discussion, which it is hoped may' lead to the discovery of the source of some of the traditional beliefs on the subject, the results of some tests are presented here, with data on heat treating, physical tests, and erosion. The detailed metallographic study of this steel is given in another paper.l The conclusions from these tests should be capable of wider application than their direct bearing on the barrel-steel problem. The Government specifications for barrel steel for model 1903 rifle (Springfield) call for carbon 0.50 to 0.60 per cent., manganese 1.00 to 1.29 per cent., silicon under 0.25 per cent., sulfur under 0.06 per cent., phosphorus under 0.08 per cent. The minimum physical requirements are: Tensile strength, 110,000 lb. per sq. in. (7733 kg. per sq. cm.); yield point, 75,000 lb. per sq. in (5472 kg. per sq. cm.); elongation, 20 per cent.; reduction of area, 45 per cent. Material fulfilling these requirements gives practically no failures when proof-fired, with charge of 70,000 lb. per sq. in. pressure, which is 40 per cent. in excess of the service charge. The turning and drilling operations show up any seams or laps such as accidentally occur even in the best heats of open-hearth steel, so that faulty stock is practically all eliminated before proof-firing. These physical requirements are met either by rolling billets at a proper temperature down to the form of tapered barrel blanks or by heat treating bars that have been upset to cnlarge the breech section. The transformation temperature of this steel, on heating, is around 1350" F. (732' C.), varying somewhat with the composition and the rate of heating. The actual treatment of the barrel blanks, as carried out by different manufacturers, gives four kinds of barrels, which will be called A, B, C, and D, for convenience. A barrels result from heat treating upset blanks by quenching at

Jan 1, 1920

By Duncan MacVichie

The iron fields described here are located in the Iron Springs and Pinto mining districts, Iron County, Utah. This region is in southwestern Utah, about 260 miles south from Salt Lake City, and is reached by the Los Angeles & Salt Lake railroad of the Union Pacific system. The iron fields lie at an elevation of 5500 to 7500 ft. above sea level, and are essentially desert in character. They are covered with a light growth of sage brush, piñon pine, and scattered cedar. Weather conditions are unusually favorable for all-year mining operations, the winters being mild with little or no snow; and the summers not excessively hot, the temperature rarely rising to 100 during the day, while the nights are invariably cool. The iron-ore bearing area extends from the Iron Springs district to the Iron Mountain mining district, being approximately 25 miles long in a northeast-southwest direction, and from 1 to 3 miles wide in a northwest-southeast direction. In the Iron Springs and Pinto mining districts, the ore occurs at various points around three sides of Granite Mountain and Iron Mountain. This is readily understood by reference to Figs. 1-4. These mountains are composed of andesite, which has been forced up through the surrounding sedimentary formation, in the form of laccoliths. An extensive report on the geology of these districts was made by Leith and Harder,' who state: The three dominating geological features of the district are three large andesite laccoliths which constitute the Three Peaks, Granite Mountain, and Iron Mountain; lying in a northeast-southwest line across the area in question. Three unconformable sedimentary series, aggregating 4000 ft. in thickness, outcrop in successive rings around these laccoliths, dipping outward asymmetrically, very steeply at the contact, less steeply farther away. Still farther from the laccoliths, lava-flows 2000 ft. thick rest in nearly horizontal attitudes on the tilted sedimentary rocks. These general relations are modified by faulting. All of the rock formations of the district are more or less covered on the middle and lower slopes by unconsolidated and partly consolidated erosion debris, both aqueous and subaerial, which spreads out on the lower ground to make the deserts.

Jan 1, 1927

By A. J. Shaler

The subject of the mechanism of sintering has received much attention in the past few years, particularly since the beginning of the series of AIME seminars in powder metallurgy of which this paper introduces the fourth. In the first of these, F. N. Rhines1 brought together and discussed the available experimental data on the sintering of pure metallic powder, and succeeded in bringing to a sharp focus the attention of workers in this field on the established observations which a satisfactory theory must explain. Several other authors3,5,6 have, in the last few years, studied the phenomena that occur when cold metallic powders, loose or in the form of compacts, are first brought to elevated temperatures. Some workers' in the field of friction have recently studied the adhesion of solid metal surfaces when they are brought into close contact. These researches have indicated that several separate mechanisms operate simultaneously, at least during the first part of the sintering process. Some of them have been called transient mechanisms4 because they are in general not absolutely necessary to sintering. Powders may be so prepared and so treated that these transient phenomena do not take place during subsequent sintering. This does not mean, of course, that their industrial and scientific importance is any less than that of the steady-state phenomena. The latter are changes that go on during sintering no matter how the powders are made or treated; they cannot be divorced from sintering. One way to analyze the process of sintering into its component parts is perhaps to distinguish between these transient and steady-state phenomena. Some of the transient phenomena have been studied in the past few years. Huttig3 has shown that, when the temperature of metallic powder is slowly raised, the following events generally occur in order: (1) physically adsorbed gases are desorbed; (2) there is an atomic rearrangement of the surface, a sort of two-dimensional "surface-reciystallization"; (3) there is a breakdown of chemically adsorbed surface compounds; (4) there is a recrystalliza-tion in the volume of the metal. All these changes are shown by Huttig and his coworkers to be completed fairly rapidly at lower temperatures than those generally used in sintering and are therefore not a part of the mechanism whereby the density of a mass of powder continues to change after long heating at an elevated temperature. But the first and third of these changes release gases in quantities which may or may not help to control the steady-state mechanisms, depending on when the voids become isolated from the outside of the compact. Among the phenomena studied by Steinberg and Wulff,8 there is the effect on sintering of residual stresses arising from the pressing operation. They found that the lateral surfaces of a green compact of iron are under a longitudinal residual tension-stress of the order of magnitude of half the yield-point for solid iron. If the outside surface is in tension, the core must be under longitudinal compression. When the compact is heated, the surface residual stress is thermally relieved first, and the compact therefore initially expands in the direction of its axis. This is a transient phenomenon, if for no other reason than the possibility of sintering unpressed powders, as demonstrated by Delisle,9 Libsch, Volterra and Wulff10 and others.1 The subject of recrystallization is dealt with further in a separate section, in view of its prominent place in sintering literature. It, too. is one of these transient phenomena. Among the steady-state parts there may be distinguished the attraction between particles and its consequences, the spheroidization of voids in the compacts, and the densification or swelling of the compact. There is considerable evidence4,7 showing that cold metallic surfaces, when brought to within a few interatomic distances of one another, are attracted to each other by forces of the order of many thousands of pounds per square inch. A calculation, discussed in greater detail in another section, shows that this force changes but slightly when the temperature of the surfaces approaches the melting point. Actual measurements of forces of adhesion of this magnitude have been made by Bradley12 on some nonmetals, but none has yet been made on cold or hot metals. This force is of sufficient magnitude to cause some plastic deformation in powder compacts, as will be shown below. A second force of steady-state nature is due to the surface tension, which probably has the same origin as the force of attraction between surfaces.164 A paper by Udin, Shaler, and Wulff1,3 gives the results of precise direct measurements of its value for solid copper. The demonstration of the tendency for the surface tension to shrink a pore was long ago given by Gibbs.17 He showed that its effect on a curved surface between two phases is equivalent to a pressure perpendicular to that

Jan 1, 1950

By Dever Ashmead

ANTHRACITE was first mined in the Wyoming Valley and sold as an article of commerce in 1808. As some preparation has always been necessary to make it ready to burn, the preparation of anthracite must date back over a hundred years. Two vital factors have determined to a large extent the degree and method of anthracite preparation. These are, first, the character of the beds worked and the methods by which they were mined and, second, the equipment used and practices followed in the burning of the coal. It is not the intention here to go deeply into these phases of preparation as a paper of no mean length could be prepared on the history of either. Rather, the intention here is to point out the main considerations and to show the influence they have exerted on the preparation of anthracite. MINING METHODS AND THEIR RELATION TO PREPARATION In the beginning f the nineteenth century, the coal beds were virgin with the possible exception of some outcroppings that had been worked, to a slight extent, by the Indians. It is known that the American aborigines had a knowledge of the use of this fuel, because when the Wyoming Valley was purchased from them, in 1754, they mentioned the fact that, by selling the land, they would lose their coal.

Jan 9, 1921

By Sydney H., Ball

ONE of the important mineral discoveries of the eighteenth century was , that of the Minas Geraes, Brazil; diamond fields. The production of this and of .other diamond discoveries in neighboring states made Brazil the premier producer of diamonds, succeeding India; its 140 years of supremacy finally passed to- South Africa- 60 years ago. Three times have diamonds contributed heavily to Portugal's somewhat checkered financial history; first in the sixteenth and seventeenth- centuries when the diamond trade of India was controlled by its citizens residing in ,Goa, later in the late eighteenth and the first 75 years of the nineteenth century when the Brazilian fields were the world's source of diamonds, and now, when the Angola diamond mines are the principal source of revenue of its colony, Portuguese West Africa. Certain phases in the history of the administration of the Brazilian field are sufficiently curious to warrant description.

Jan 1, 1929

By Robert D. Pehlke, Arden L. Bement

A mass transfer coefficient for the removal of hydrogen from liquid aluminum by inert flush degassing has been determined experimentally at 700°C. A mathematical model has been derived, assuming transport control, which adequately describes the experimental data. The removal of hydrogen is shown to increase with decreasing bubble size, and with increasing flow of flushing gas. The presence of hydrogen in liquid metals in amounts which exceed the solid solubility at one atmosphere hydrogen pressure is highly undesirable, causing unsound ingots or castings, or resulting in difficulties during further fabrication. The removal of hydrogen from liquid metals can be accomplished by several methods, the principal two being vacuum treating and inert flush degassing. The design of a process involving either of these techniques is based on the mass transfer coefficient for hydrogen between the liquid metal and a hydrogen-dilute gas phase. In an effort to extend our knowledge in this area, an investigation of the rate of removal of hydrogen from liquid metals by inert gas flushing was undertaken. In view of the difficulties encountered with gas porosity in the casting of aluminum and aluminum alloys, and because of certain experimental advantages, liquid aluminum was selected for the study. PREVIOUS INVESTIGATIONS The removal of gases from liquid metals, particularly steel, has received considerable attention in recent years, The first definitive work of a theoretical nature was presented by Geller1 who considered the case where equilibrium exists between purging gases and metal bath during flushing, and also deviations from this ideal case. Hulme2 has surveyed a number of experimental studies and discussed some of the practical limitations of removing dissolved gases from molten metals. More recently a number of studies have been reported on degassing of steel melts by flushing with an inert gas.3'4 Considerable work has also been reported on aqueous and organic liquid-gas systems, and an excellent summary prepared by Hovis.5 The treatment of liquid aluminum by a flushing gas to remove dissolved hydrogen has been known for several decades.6 A number of gases have been used for this purpose, including nitrogen, argon, and chlorine, or mixtures of these gases. Tikkanen and Erkko7 have studied the relative density changes of aluminum castings poured from melts degassed with chlorine, nitrogen, and mixtures of the two gases. Their

Jan 1, 1962

By A. Satter, J. M. Campbell

Reported herein are the results of a careful and detailed study of the non-ideal behavior of pure gases and their mixtures. Included are: (1) new data on five ternary systems composed of methane, ethane and H2 S; (2) a simple compressibility factor correlation that is inherently superior to present correlations, particularly for gases containing H2S and CO2; and(3) a detailed study of combination rules and the effect of system composition on the choice thereof. This study makes use of the rather large mass of data already available in the literature. A complete re-examination of the data and ideas presented in the last 25 years was considered desirable as a prelude to our basic concern — the effect of diluents on gas behavior. A consideration of both the macroscopic and microscopic properties of gases provides a better insight which, in turn, gives a firmer basis for improved correlation techniques. Such a study has shown that expressing the compressibility factor Z as a function of acentric factor w, as well as reduced temperature and pressure, yields a correlation that is broader in scope. The study of various combination rules has shown that better results are obtained by "tailoring" the rule used to the system composition. To do so improves the basic reality of results by overcoming some of the anomalies often found when using Kay's rule alone. Tentative recommendations are made regarding the most reliable combination rule for use with a given class of gas. The data presented are useful for estimating the direction and magnitude of the expected deviation when using a given rule. Although more work is needed, particularly around the critical region and with CO2 mixtures, the advantage of the classification scheme proposed is apparent. INTRODUCTION When one attempts to write a PVT equation to fit the data for actual gases, greater precision is obtained by the use of a multiple number of empirical constants. This has lead to multiple-constant equations such as Benedict-Webb-Rubin, Beattie-Bridgman, Keyes, etc., which are capable of yielding very precise results for pure gases in a range for which data to get the constants are available. As a matter of practicality, though, the use of such equations for gas mixtures is limited. Because of the infinite number of gas analyses available, any attempt to compile the constants needed requires a prohibitive amount of experimental data. This could be overcome by the use of a combination rule, but there is no real advantage in doing so because the end result offers no practical impovement over the Z factor correlation. The most widely used method of predicting the volumetric properties of pure gases is based upon the "theorem of corresponding states". According to this theorem, "all pure substances have corresponding molal volume at corresponding temperature and pressure if the reference point of correspondence is the critical point". Generalized compressibility charts for gases were prepared first by Cope and associates1 in 1931 and later by Brown and co-workers2 in 1932. However, the most commonly used charts are those of Dodge,3 Nelson and Obert,4 Hougen and atsson: and Standing and Katz.6 The work of Katz and co-workers has provided us with basic data for the hydrocarbons most widely used today. Their original chart6 was compared with a relatively large amount of multi-component data for gases consisting almost entirely of normal paraffin hydrocarbons. A deviation of only + 1.2 per cent was obtained.39 In the 20 years following publication of this work it has been found that the behavior of most mixtures of paraffin hydrocarbons could be predicted by this correlation within at least 5 per cent. Where difficulty has been encountered it has largely involved one or more of the following circumstances: pressures above 4,000 psig, mixtures containing large amounts of heavy ends and/or aromatics, systems in the critical region and mixtures containing polar compounds and/or CO2. The abnormal error sometimes found with such gases, not too unexpected for this method, is

By Theodore J. Hoover

WHAT are the chief branches of the mining engineering profession today? In an effort to analyze the structure of the profession, for practical purposes, a quantitative study has been made of the membership of the A.I.M.E., and is herein reported for the first time. In spite of the effect that a long history and a relatively small group of professional workers have had in limiting specialization in mining engineering, there has nevertheless grown up a wide variety of specialties in this field. More than a hundred different kinds of engineers were discovered among the titles given by Institute members in the Directory, ranging from "advisory engineer" and "American engineer" down to "wire-rope engineer" and "works engineer." How should all these titles be defined and interpreted? How many of them should be relegated as meaningless or confusing? What are the relationships among the remaining useful designations? Should some of them be grouped as "metallurgical" or "chemical," or under some other head?

Jan 1, 1935

By W. A. Backofen, G. Y. Chin, W. F. Hosford

The effect of machine stiffness on discontinuous flow and fracture of the 2024 aluminum alloy was studied in tension at 4.2OK. An increase of machine stiffness was found to decrease the amount of elongation and drop in load during discontinuous flow, thereby postponing fracture to larger strains and higher stresses. The possibility of utilizing stiffened tools in deformation processing to suppress shear fracture originating from unstable flow was indicated. The problem of nucleating discontinuous flow and the role of the effective mass of the system in discontinuous flow were also considered. AT low temperatures the plastic flow of metals is often discontinuous, with sudden load drops and elongations.1,3 Basinski1,4 has presented strong evidence that discontinuous flow, at least in aluminum alloys, occurs under nearly adiabatic conditions. During testing the load may drop suddenly and flow become localized when the thermal softening, due to heat generated in plastic straining, is greater than the strain and strain-rate hardening. This instability criterion is more easily satisfied at low temperatures because 1) the volume specific heat is reduced so that relatively large temperature increases are possible in straining, and 2) the flow stress is relatively temperature-dependent. The important role of adiabatic shear in ductile fracture processes has been emphasized,5-1 and consideration has already been given to the influences of thermal and mechanical properties on the tendency of a material to undergo adiabatic shear.17677 By focusing attention on how the mechanical loading system influences low-temperature discontinuous flow, additional insight into adiabatic shear and its effect on fracture may be gained. EXPERIMENTAL PROCEDURE Because of its low thermal conductivity, the 2024 aluminum alloy exhibits a highly consistent discon- tinuous-flow behavior at 4.2°K and was therefore chosen as the material for study. Machined specimens of 0.113 in. diam and 1.125 in. gage length were solution heat-treated at 490°C for 3 hr, quenched into cold water, and immediately immersed in liquid nitrogen until just before testing. Testing was done at 4.2°K by immersion in liquid helium at a crosshead drive rate of 0.03 in. per min. As normally used (hard-machine basis), the spring constant of the testing machine was k = 25,000 lb per in. By inserting beam springs in series with the specimen, this value could be lowered by a factor of about 100. Details can be found elsewhere.? As a result of variable machine stiffness, the actual strain rate ranged from about 3 x 10 5 to 3 x 10-4 per sec from one test to another, as well as within any one test. However, preliminary tests had established that the tensile curves were not altered significantly by this strain-rate variation. Fig. 1 shows a typical load vs plastic-elongation curve for a solution heat-treated 2024 aluminum alloy specimen pulled in the standard hard machine (k = 25,000 lb per in.) at 4.2"K. The elastic extension has been subtracted. Plastic flow proceeded smoothly from yielding at approximately 22,000 psi (load = 220 lb) to a strain of about 4 pct at which point the flow became discontinuous. The magnitude of the load drops as well as the plastic elongation per drop increased with increasing strain until the specimen finally broke abruptly. The load-elongation behavior of a sample tested with a relatively soft machine under otherwise identical conditions is given in Fig. 2. In general, there

Jan 1, 1964

By W. H. Bassett

ABOUT twenty-five years ago the copper industry had outgrown the Lake Superior production. The electrolytic copper producers had- their process well in hand and the industry was well started in the use of electrolytic copper, both for working into wire and sheet, and for the making of alloys. The trade knew that some brands of copper made good material and that other brands did not. There came together a group of men-a refiner, a rolling-mill man, and a manufacturer of electrical machinery-each of them desiring to know why there was a difference and what .it was. Much investigation was done with wire bars and cakes which involved ' chemical analysis, metallographic examination, physical tests and electrical tests. To find the influence of different kinds of copper in making brass 200 carloads of ingots were made into ,eyelet brass under careful observation; each carload was carefully analyzed and tested before used. The alloy was made and rolled under standard conditions and the results recorded.

Jan 1, 1924

By M. C. Smith, W. V. Green, D. M. Olsen

The creep-rupture behavior of commercial powder-metallurgy molybdenum rod is reported in the temperature range 1600" to 250O°C, at stresses up to 9000 psi and times up to 1 month. The effects of temperature, stress, and grain growth are discussed. Rupture time is fitted to the Larson-Miller parameter and compared to lower-temperature and higher-stress results reported by pugh.1 BECAUSE of its high melting point, molybdenum should retain useful strength to relatively high temperatures. Combined with its ready availability in the United States, this makes it attractive for many applications in missiles, rockets, and so forth—wherever its susceptibility to oxidation can be tolerated or overcome. The mechanical properties of molybdenum rod in the temperature range —200" to 1540°C have been reported by pugh,' Bechtold,' Parke,3 and Carriker and Guard.4 Madden and chen5 have measured the tensile properties of molybdenum single crystals in vacuum up to about 2500°C. As one further step in evaluating its mechanical usefulness, the constant-load creep-rupture properties of commercial powder-metallurgy molybdenum rod have been investigated in the range 1600" to 2500°C. MATERIAL TESTED Creep specimens were machined from 1/2-in. round commercial molybdenum rod, manufactured from powder by pressing, sintering, and swaging. Spectrochemical analysis of the rod showed "traces" (less than 0.01 pct) of silicon, aluminum, chromium, iron, and zirconium, and "faint traces" (less than 0.001 pct) of manganese, magnesium, cobalt, and nickel. Carbon content was 130 to 200 ppm, nitrogen was 110 to 180 ppm, and oxygen 30 to 35 ppm. A typical microstructure of the as-received rod is shown in Fig. 1. Room temperature tensile properties for five specimens strained at about 0.015 in. per in. per min are shown in Table I. CREEP SPECIMENS USED The specimens used for creep-rupture testing are illustrated in Fig. 2. The 1/4-in.-diam gage section was 3/4 in. long, and terminated at shoulders 5 mils high. These shoulders served as fiducial marks for optical strain measurements. Surface finish on the gage section was 16pin. r.m.s. One specimen, for a "long-time" test described below, was modified by dividing the 3/4-in. gage length into three 1/4-in. long sections with individual diameters of 0.250, 0.230, and 0.210 in., each terminating in a pair of fiducial shoulders. TESTING PROCEDURE The constant-load creep-testing machine used has been described by Smith, Olson, and Brown.6 In it the specimen is held vertically on the axis of a cylindrical tantalum or tungsten heater tube by threaded molybdenum or tungsten grips. Both specimen and grips are heated by radiation from the heater-tube, which is heated by its own electrical resistance. The bottom specimen grip is held at its lower end by a clevis pin. The testing load is applied to the specimen through the upper grip by means of hanging weights, a constant force-multiplication lever system, and a pull rod sealed to the chamber lid by a bellows. The incandescent specimen is viewed by an external optical system through slots in the heater-tube and radiation shielding, and an enlarged image of it is projected on a ground-glass screen. Gage-length measurements are made on this image with a pair of cathetometers. Thorium oxide coatings were applied to the threaded ends of most specimens, to prevent diffusion-welding of specimens to grips during testing. Without such a coating welding usually occurred, and grips were often broken by subsequent efforts to remove the tested specimens.

Jan 1, 1960

By Floyd C. Kelly

A. HUltgren, .Söderfors, Sweden (written discussion*).—From the results obtained in his own experiments as well as those of Austin and of Grube Mr. Kelley derives a general law, expressed tentatively in the following words: "whenever two metals are brought into intimate contact at a temperature at which diffusion takes place, a comparatively rapid, or abnormal, grain growth results." It is suggested that,, in order adequately to represent the facts, this definition should he restricted by the following qualifications: a and b are the two metals, b diffusing into a. A. At the temperature in question a should exist as phase a 1 having a limited solubility for b. B. The supply of b by diffusion should be sufficient, in view of the rate of diffusion into a 1, to increase the concentration of b above the saturation value in a 1 so as to cause a new phase a2 to form. (7. The phase a2 should have a range of solubility for 6, thus rendering continued diffusion possible. D. In order that the columnar grains may be preserved in the structure the phase a2 should, of course, not suffer transformation on cooling. The phenomenon thus defined may be described as progressive transformation by diffusion. Its mechanism would appear to he as follows: Fig. 17 shows a portion of the equilibrium diagram a-b, Fig. 18 the distribution of b in solution after various periods of diffusion, Fig. 19 represents the structure in cross-section of a cylindrical rod of a at the end of heating period 3. 1. The first effect of diffusion of b into a will be to establish a concentration gradient in phase a1 (1, Fig. 18). When the saturation value for the temperature of the experiment (m, Fig. 17) is reached at the surface, nuclei of, a2 of composition n will form here, and later develop into a continuous layer. Assuming that diffusion proceeds without irregularities and that transformation at any point sets in without lag—i. e., in the moment saturation is exceeded—the transformation a1-a2 will advance inwards on a cylindrical surface concentric with the surface of the rod. The discontinuity of composition at the transformation surface in the position it happens to have at the end of the treatment (3, Fig. 18) will be preserved at room temperature, if the cooling is not particularly slow, and be recorded in the structure as a marked, smooth line, in agreement with Grube's and the author's observations. The shape of the distribution curves in Fig. 18 is also corroborated by the analyses given by Grube. 2. During diffusion, since the secondary phase a2 is always in immediate contact with the saturated part of the primary phase a1, there should be very little lag in the transformation. This means that the first a2 grains formed should grow in preference to the formation of independent nuclei; in other words, columnar growth results. It does not seem necessary to assume, with Green,' whose conception of the phenomenon

Jan 1, 1929