Search Documents

By Basil B. Zavoico

The production of all Russian fields incressed from approsimatctly 74,000,000 bbl. during 1926-27, to approximately 83,000,000 bbl. during 1927-28. Of this amount Baku was responsible for 54,.500,000 bbl., Grozny for 25,800,000 bbl., and Emba for 1,200,000 bbl. Accordingly, the proportional importance of the Grozny oil field has been considerably increased, the present production being twice that of 1913. The most notable factor of production during 1927-28 was the importance of gushers; 40.8 per cent. of the total was thus obtained. In the Baku fields 26 per cent. of the total, and in Grozny 74.2 percent'. of the total were produced by naturally flowing wells. This may be explained by the reduction in authorizations for drilling by the central authorities, and, accordingly, the local trusts increased the production to the planned figures at the expense of the proved prolific reserves. In Baku region, the Surnkany oil field produced 36.1 per cent. of the total Baku production, or an equivalent of 53,800 bbl. per clay, the largest percentage coining from the fifth horizon. Nest year's plans call for continual development of that horizon as well as of the sixteenth horizon in the Bibi-Eibat field, which was opened lately. In the Grozny fields the New Area (Bellik) WAS responsible for 79.4 per cent. of the total production. The authorized plan for 1928-29 production calls for 92,200,000 bid., and a reasonably accurate estimate for 1932--33 production is placed at. 156,000,000 bbl., with Baku contributing 101,800,000 bbl., Grozny 44,100,000 bbl., Emba 6,200,000 bbl., Kuban 2,100,000 bbl., Saghalien Island 1,400,000 bbl., and Russian Turkestan 400,000 bbl. In connection with recent discoverices in the Baku area these figures art. quite conservative. The average production per well per day in the Baku oil fields was 49.2 bbl., in Grozny 175 bbl.; in detail, Surakany oil field averaged 250 bbl., and the New Area in Grozny 514 bbl. per day. New completions in all Baku fields averaged 264 bbl. per day, and in Grozny 970 bbl. pel. day. These figures show a considerable progress in the technical developnlent of all fields, compared even with the prerevolution figures, since all the mprovements are noted in the fields that arc over 30 years old.

Jan 1, 1929

By P. H. G., Durville

ANY metal which contains even a small percentage of aluminum possesses certain peculiarities of appearance and properties which are exhibited both when the metal is melted and after it solidifies. Pure aluminum, or an alloy containing a small proportion of aluminum, can be melted without flux-except for a layer of charcoal-because a film of aluminum oxide and metal forms at the surface of melted aluminum. Although very thin, this film is air-proof, and it prevents the metal underneath from oxidizing. This oxidized film does not move easily on account of its toughness and high surface tension. One very important point in connection with this process of still casting has not been strongly enough stressed, namely, that the same kind of surface film with the same peculiarities forms over the surface of all melted alloys that contain even a small proportion of aluminum. Experienced foundrymen know how desirable it is to cast aluminum under its "skin" or under the surface of the film which tends to remain still. In the case of red copper, when in fusion, the surface shows pure copper only. This' is due to the fact that liquid copper constantly absorbs the copper oxide which forms on the surface. By closely examining melting copper the oxide can be seen dissolving in the bath, and going into solution just as pulverized sugar dissolves in water. When copper is cast in the open, either in wire bars or cakes, the surface of metal exposed to the air is covered by a film of black oxide that cannot be absorbed by the metal.

Jan 1, 1927

By D. Turnbull, H. N. Treaftis

Precipitation of tin from Pb-Sn alloys (lead-rich) occurs by the nucleation and growth of hemispherical cells which consist of tin lomelloe interspersed in the depleted solid solution. Nucleation and growth of these cells and the tin interlamellar spacing at various compositions and temperatures have been investigated. The interlamellar spacing increases approximately as the reciprocal of the logarithm of the supersaturation ratio. For constant initial tin concentration the concentration of cell nuclei increases with decreasing temperature to a limiting temperature-independent value. The kinetic results support the view that the cell growth rote is governed by the diffusion of tin along the cell boundary. In the main, the results confirm the authors' earlier deductions, drawn from resistometric and calorimetric data, about the precipitation mechonism. IT has been shown1, 2 that tin (ß) precipitates from lead-rich (a) PbSn solutions by the nucleation and growth of cells (cellular or discontinuous precipitation). These cells consist of tin lamellae, with a spacing 1, interspersed in a depleted a solution. Reorientation of a also accompanies cell growth. The kinetics of cellular precipitation of tin from lead have been measured by resistometric2, 3 and ca1orimetric1, 3 techniques. The time-transformation isotherms (t equals time; x, volume fraction of specimen transformed) of the initial rapid precipitation, which drains about 60 pet of the tin from solution, have been described by a kinetic law having the form x = 1 —exp (—bt n) [I] where n usually has the value 3.0. It was shown" that this law and the other kinetic facts can be explained satisfactorily if it is assumed that the cells grow at a constant rate and that all the cells nucleate in a time negligible in comparison with the period of cell growth before impingement. Thus, for hemispherical cells b = (2/3)pNG3 [21 where G is the rate of cell growth in cm per sec, and N is the number of cell nuclei per unit volume. The rapid rate of cell growth at low temperatures can be accounted for"' if it is assumed that the dissolved tin drains to the lamellae edges by diffusion along the sweeping cell boundary rather than by diffusion through the a crystal (volume diffusion). For cell growth governed by cell boundary diffusion it was shown, approximately G=2(X° - X° / X° ) DBA / l2 where A equals the thickness of the cell boundary; D R, the coefficient of diffusion of tin atoms within the boundary; and X° and X, are the atom fractions of tin in the supersaturated and saturated solutions, respectively. Zener8 had already shown that, where

Jan 1, 1959

Jan 1, 1963

By AIME AIME

THE Institute of Metals held a well rounded out symposium on the working of metals, distributed over two sessions. At the first session* four papers were presented, two dealing with the, cold working of metals and alloys and two with the hot working of non-ferrous alloys. The first paper by E. V. Crane, dealt with "Metal Working in Power Presses." Mr. Crane pointed out the empirical nature of engineering data available for use in calculating the probable stresses developed and power requirements, for the shearing, drawing, binding and other forming operations. He described the various operations, methods of determining stresses developed and presented data obtained. In the discussion C. F. Hammond took exception to Mr. Crane's objections to the rather too frequent. annealing operations in drawing of cartridge cases, pointing out that the material was-manufactured to meet specified structure and physical requirements, which could only be met by carefully controlled sequences of working and intermediate annealing operations.

Jan 1, 1931

By H. C. LIVINGSTON

At the Hanna No. 4-A mine of The Union Pacific Coal Co. a new system of trackless mining is being utilized to extract a 26-ft coal seam. By using shuttle cars and a conveyor belt for haulage in the rooms and panel entries instead of pit cars and panel hoist a saving of 12 cents per ton is expected. Mining is conducted in a 26-ft coal seam laid down on a synclinal structure with active workings on a pitch of approximately ten to twelve degrees. The coal seam is interbedded between a shale bottom and sand- stone top. The coal is friable, high in moisture, and subject to spontaneous combustion. The mine is rated gassy by the State Coal Mine Inspection Department. Mining is conducted at the present time by unbalanced rope haulage an main slopes spaced on approximate 4300-ft centers with the three-entry system driven to boundary lines, strike entries being turned on approximate 1300-ft centers. Panels are driven to the rise between entries at approximately 750-ft intervals with panel rooms driven on the strike 500 to 600 ft long, leaving 150 ft of barrier pillar between each block of panel rooms.

Jan 1, 1949

By F. W. Jessen, C. C. Patton

Adsorbed films were formed on polished stainless steel specimens from dilute benzene solutions of two crude oil distillation residua. Although the two residua were extremely dissimilar in composition, contact angle measurements showed that the two films increased the wettability of the steel specimens to oil by equal amounts. Furthermore, the wettability of the films was essentially unaffected by the desorption techniques used. Paraffin deposits were formed from heptane-wax solutions on the same stainless steel specimens. These deposits definitely adhered to the surface. Presence of an adsorbed crude oil film on the metal surface increased its free surface energy and resulted in increased deposition of paraffin. The addition to the heptane - wax solution of small amounts of the same distillation residua that were used to form the adsorbed films resulted in decreased cohesive strength in the deposits formed, which resulted in decreased deposition. The presence of a crude oil fraction both in the solution and as a preadsorbed film eliminated the adherence of a deposit of any kind. A mechanism of deposition is proposed which explains the results obtained. INTRODUCTION The natural formation of any predominantly organic accumulation in oilwell tubing, surface flow lines or other production and storage facilities is called a paraffin deposit. These deposits restrict the production of crude oil, causing a substantial increase in production costs because of decreased flow capacity, expense for periodic deposit removal and unproductive downtime. The conditions under which such deposits form, their physical characteristics and the nature and severity of the problem created are extremely varied. Over the past several years, much progress has been made in developing and utilizing methods to remove accumulated paraffin deposition. However, like so many other problems, the basic stumbling block appears to be a lack of understanding of the fundamental mechanism involved in the formation of such deposits. Crude petroleum is known to contain considerable quantities of polar, surface active substances which Doddl has shown to be present at the oil-water interface. Denekas, Mattax and Davis2 observed that the wettability of reservoir rocks was drastically altered by exposure to crude oil fractions; and Zisman, et a1.3 showed that the nature of the compounds adsorbed on a surface would determine its wettability characteristics. Cole and Jessen4 and Ehrig5showed that surface wettability can have a profound effect on the magnitude of paraffin deposition, and Parks6 demonstrated chat the presence of certain adsorbed films on a metal surface would reduce the adherence of paraffin to that surface. Zisman7 has since advanced the theory that the conditions for adhesion are the same as for wetting. Therefore, it was felt that there was adequate evidence to support the supposition that adsorption of compounds from a crude oil might play an important part in paraffin deposition. ADSORPTION-WETTABILITY EXPERIMENTS Initial experiments were conducted to determine the effects of adsorption from solution of crude oil residua on the wettability of a polished stainless steel surface. Distillation residua with initial atmospheric boiling points of 700F were used in preference to the whole crudes in order to concentrate on the molecular weight range of interest, and to eliminate the possibility of composition change due to evaporation of the light ends. Also, these high boiling materials would be expected to be adsorbed from the whole oil in preference to similar compounds of lower molecular weight.

Jan 1, 1966

By Davis M. Lapham

Ore bodies at Cornwall, Pennsylvania, have been mined since 1742 principally for iron from magnetite, but also for copper (in chalcopyrite), silver (in chalcopyrite), gold (in chalcopyrite), cobalt (in pyrite), sulfur, and crushed limestone aggregate. Metallization occurs as a limestone replacement above the essentially conformable, south dipping portion of a discordant saucershaped diabase sheet. Pre-Triassic and Triassic faulting have emplaced host Cambrian limestone and two Ordovician(?) hornfels units, now for the most part resting above diabase. Thermal metamorphism of carbonate-bearing country rocks largely to calc-silicates, is ubiquitous. Metasomatism, particularly of potassium, is unique to ore zones. Associated magnetite- actinolite mineralization replaces, in a preferential sequence, all earlier metamorphic and metasomatic minerals and rarely diabase chilled margin. Mineralogical (diopside, actinolite, mica, sulfides, oxides) and chemical (Fe, Cu, S, Co) zoning of the eastern ore body is focused down dip, near its western edge, along a major vertical fault through diabase. This zoning is spatially related to magnetite veins in diabase, to an ore body within diabase, and to a shear zone that probably extends through the sheet.

Jan 1, 1968

By AIME

Burton J. Westman-Besides decreasing the diamond size, there appear to be two other approaches open to overcome excessive diamond loss and, more particularly, the rapid diamond polish that took place in this quartz-feldspar rock. First, however, a short discussion of the diamond characteristics should be made in order to discuss the situation more clearly. The West African diamonds which we can assume were used. for this drilling have two disadvantages when drilling hard, exceptionally fine-grained rocks. These are rapid polishing and, if .the bit isn't "drilled in" carefully, a tendency to damage, resulting in excessive diamond loss. The normal wear resistance of any diamond is inversely proportional to the compressive strength of the diamond, therefore only the highest grade, of diamonds free from insipient fractures should be employed. Using upwards of 90 diamonds per carat instead of the20 to 30 per carat not only decreases the total projected area of the cutting points but increases the stress per point which, in turn, causes greater depth of penetration into the rock. Considering this depth of penetration, therefore, suggests an approach other than increasing the, number of diamonds per carat and that is to decrease the actual number of diamond points (also the carat weight per bit) so that the penetrating force on an individual diamond is increased. This penetration increases the chipping or rock shearing action.

Jan 1, 1950

By E. V. Potter, H. C. Lukens

THE volume of hydrogen released from electrolytic manganese at various temperatures and pressures was determined in a previous investigation1 as part of a study to determine the most practical procedure for removing the hydrogen from electrolytic manganese metal. No attempt was made to determine the absolute volume of gas in the metal at any temperature and pressure; the volume of gas released showed only the variation in solubility with temperature and pressure. The results were very similar to those obtained by Sieverts and Moritz.2 Both sets of data show a minimum solubility between 500° and 700°C., but they differ in certain respects; on cooling from 500°C., our results showed an increase in solubility of about 7 C.C. as compared with an increase of 34 C.C. per 100 grams shown by Sieverts. Furthermore, the transition temperatures, as indicated by sharp breaks in the solubility curves, did not agree well with Sieverts' data. This information was of secondary importance in the earlier investigations, and the solubility at low temperatures and the transition temperatures were subject to considerable error. There- fore, a subsequent investigation, reported in this paper, was made to measure the absolute solubility at temperatures from room temperature through the melting point and make more accurate observations of the transition temperatures. APPARATUS AND METHOD The apparatus and method were essentially the same as those described in the previous work,1 as shown in Fig, I. At high temperatures, the small tube containing the thermocouple in the sample container A frequently broke off, so for some of this work the thermocouple was placed outside the sample container and protected by a quartz tube of about the same wall thickness as the sample container. No significant difference was found in the transition temperatures obtained in the two ways. The automatic temperature controller was used in these tests in the regions where there was little change in solubility with temperature. In the neighborhood of the transition points a continuously variable autotransformer was used instead of the automatic controller, and the power input to the furnace was adjusted so that the temperature increased or decreased at a very slow, uniform rate through the transition range. This procedure was followed because the temperature oscillations produced by the controller were too great compared with the transition range, and the transition points determined under such conditions were less accurate. ABSOLUTE SOLUBILITY Procedure and Results The absolute solubility of hydrogen in manganese could be determined most

Jan 1, 1946

By T. J. Koppenaal, M. E. Fine

A yield point effect attributed to short-range ordevi?g (SRO) occurs in Cu base Al. At at 296°K varies with heat treatment, decreasing as the annealing ternperature is raised .from 433Oto 598°K. Davies aid Cahn' observed a corresponding decrease in SRO. (523 °K anneal, measured at 77°K) is approximateZy proportional to the variations of A7 with strain rate and testing temperature are also Consistent with the idea that is associated with SRO. A preliminary investigation of the tensile properties of a Cu-Al single crystals showed the presence of a rather strong yield-point effect (drop in flow stress after initial yielding). The object of this research was to investigate its origin and behavior. a Cu-Al alloys are particularly interesting because diffuse X-ray scattering measurements by Davies and Cahn,' Houska and Averbach,' and Borie established the presence of short-range order. The degree of local order may be changed with heat treatment.' cottrel14 suggested that the presence of local order might result in a yield-point effect, and thus the possibility exists here for experimentally ascertaining the importance of short-range order with respect to yield points in these alloys. Since a 12 pct difference exists between the atomic sizes, elastic or Cottrell locking5 must also be considered. Further, Howie and swanne have shown that the stacking fault energy of copper is reduced by aluminum additions. The width of extended dislocations should thereby increase. hus the conditions appear attractive for Suzuki locking.' Finally, the possibility of stress-induced order at dislocations, schoeck locking,' must also be examined, EXPERIMENTAL PROCEDURE Alloys up to 14 at. pct Al were prepared by induction melting high-purity (99.999 pct) Cu and (99.996 pct) Al in a graphite boat under a dynamic vacuum of 5 X 10o mm of Hg. After homogenizing the ingots at 900°C for at least 24 hr under vacuum, they were rolled with intermediate anneals to strips 1.55 mm thick. Single crystals 10 in. long were grown by lowering strips, contained in a split graphite mold sealed in fused quartz at 5 X lo-' mm of Hg, through a single coil induction heater at a constant rate of 1/2 in. per hr. Tensile specimens 1.25 in. long were cut from the single crystal strips and reduced cross sections about 0.7 in. long and 3.0 to 3.5 mm2 in area were introduced by filing and abrading.8 To remove the worked portion about 10 pct of the cross-sectional area was removed by etching. Back-reflection Laue photographs of a filed and etched specimen were taken before and after annealing at 900°c for 24 hr. Small, well defined Laue spots were obtained with no visual difference in the two photographs. Further, specimens with and without the reduced sections began yielding at about the same stress. Hence, for our purposes, filing and abrading did not affect the structure of the specimens. Each single crystal specimen was annealed at 900° c in vacuum for at least 24 hr and furnace cooled; while cooling through the range of 250o to 200°c, the rate was about 55°C per hr. Orientations were determined by the usual back-reflection Laue

Jan 1, 1962

By H. O. McLeod, J. M. Campbell

Data analysis of pentane and hexane adsorption from natural gas in a fixed bed of silica gel shows that constant length mass transfer zones form, the curvature of the adsorption isotherm controls the growth of the mass transfer zone and surface diffusion of molecules inside the silica gel particle controls the mass transfer rate. Curvature of the hexane isothem is more than the curvature of the pentane isotherm. Because of this curvature the hexane adsorption zones reached a constant length. In contrast, the pentane adsorption zones were always increasing in length during each run. A procedure was developed to obtain correct mass transfer coefficients using effluent curve slopes. These transfer roefficients increase with the amount of hydrocarbon adsorbed on the silica gel particle. The characteristic shape of the hexane effluent curves also show that molecular diffusion inside the silica gel particle controls the adsorption rate of pentane and hexane. INTRODUCTION The purpose of this study was to determine the mechanisms that control the dynamic adsorption of hydrocarbons from a natural gas onto silica gel. Before one can deal effectively with multicomponent adsorption, the transfer mechanisms by which a single hydrocarbon component is adsorbed from the gas stream must be defined. Two principal investigations of this system have been published ' and indicate that diffusion through the gas around the particle controls the adsorption rate. Some of the experimental observations in each study either do not support this transfer mechanism or are inconsistent with the mathematical model used in analysis. In this study surface diffusion of molecules inside the particle controls the mass transfer rate of pentane and hexane. This mechanism is indicated by the effluent curve shape for a constant length transfer zone and by the variation of the mass transfer coefficient with concentration of the adsorbed hydrocarbon. THEORY AND DEFINITIONS — MATHEMATICAL MODELS Mathematical solutions for the isothermal adsorption of a trace component from a carrier gas are derived from three relationships: the mass balance or continuity equation, the equilibrium relationship between the gas and solid phases, and a mass transfer rate equation. The transfer rate is proportional to the adsorbate concentration gradient within either the gas or solid phase. Mathematical solutions of these equations usually give the adsorbate concentration as a function of time and distance from the bed inlet. That part of the bed in which the adsorbate concentration changes from a maximum to a minimum value is called the transfer zone. This transfer zone is directly related to a plot of the effluent concentration vs time which has a characteristic S-shape. This general shape is determined by the continuity equation and occurs in many processes of diffusional transfer.

Jan 1, 1967

By H. R. Peiffer

Recently artin has indicated that the recovery of resistivity at 145°C following elongation of molybdenum at room temperature was the result of the annihilation of vacancies. The activation energy for this process was, according to Martin, 1.26 ev. This energy seems to be a reasonable one for the activation energy for the diffusion of vacancies in molybdenum. However, impurity atoms such as carbon, nitrogen, and oxygen4 have an activation energy for diffusion in molybdenum of the same order of magnitude (i.e., 1.45, 1.15, and 2.09 ev, respectively). Cottrell and Churchman have already correlated the return of impurity atoms to dislocations in cold-worked iron with the return of the upper and lower yield point. According to cottrel16 the diffusion of carbon atoms to dislocations results in the return of the yield point. As the carbon atoms become trapped by dislocations, Bhatia has shown that a decrease in the electrical resistivity is to be expected. Cottrell and Churchman were able to correlate experimentally the decrease in electrical resistivity with the return of the yield point. Since one would expect strain aging to occur in molybdenum, an experiment was performed to determine whether the resistivity recovery at 150°C for molybdenum cold-worked at room temperature can be correlated with the return of an upper and lower yield point. For this experiment 3/16-in. tensile bars of Climax molybdenum, 99.961 pct pure, were used. The specimens were annealed at 1000° C for 1 hr in an argon atmosphere and then were elongated up to 10 pct on a Baldwin-Lima-Hamilton FGT

Jan 1, 1959

By R. J. Watson, A. H. Juch

About half a million sucker-rod pumps are installed in oil wells in the U. S. alone. In Venezuela, too, the system is widely used; some 5,000, or 90 percent, of Cia. Shell de Venezuela's wells produce a total of 400,000 BOPD by this method. Most of the crude pumped is viscous, gassy and contains relatively small amounts of free water. API gravities vary from 90 to 16O; dead oil viscosities vary from 10 to 10,000 cp at the pump; and GOR's range from 100 to 2,000 cu ft/bbl. Pumps are set at depths ranging from a few hundred to 6,000 ft; the average setting depth is about 2,500 ft. From the literature, it appears that although recent years have seen significant progress toward understanding the rod pumping system as a whole, relatively little attention has been paid to those key items, the sucker-rod pump and the subsurface gas separator or gas anchor. Perhaps because of proration in the U. S., pump manufacturers have seemingly concerned themselves more with the durability of their product, achieved mainly through robust design and metallurgical know-how, than with its working efficiency. In 1963, CSV commenced a major rehabilitation and expansion of its heavy oil fields along the Bolivar Coast. The advent of the more efficient gravel-packed completion and of large-scale thermal recovery (mainly steam soak) operations resulted in well potentials *Now with B. I. P. M., The Hague, The Netherlands. greater than pump capacities. Hence, an urgent need arose to improve over-all pump efficiencies and to attack those special problems related to the production of both the extremely viscous and the hot, steam-laden crudes that formed an increasing proportion of the total stream. There followed a detailed investigation and testing program, carried out in close cooperation with a major pump manufacturer. This culminated in the introduction to the oil industry of a new line of sucker-rod pumps. Early Investigations and Experiments Field Tests Extensive field tests were carried out in three primary Bolivar Coast wells with an in-situ dead oil viscosity ranging from 400 to 6,000 cp. In these installations provision was made to (1) monitor bottom-hole pressures below, in and above the pump by means of pressure transducers, and record casing- and tubing-head pressures continuously; (2) measure accurately the annulus gas, as well as measure the tubing gas and liquid production from the well; (3) take special PVT samples of the well fluid; (4) measure power consumption of the prime mover; and (5) measure the rod loads at the polished rod. A typical test installation is illustrated in Fig. 1. It was established from the pressure transducers that with viscous oils, there is considerable flow resistance across the pump and gas anchor assembly. Pressure surges were observed over each pump cycle,

Jan 1, 1970

By B. A. Wilcox

ThERE are several reports in the literature which indicate that both solid-solution hydrogen and hydride precipitates can promote low-temperature em-brittlement of tantalum.1-3 For example, Imgram et al.2 showed that hydrogen additions in the range of 140 to 580 ppm promoted a ductile-to-brittle transition at slightly above room temperature in both wrought and recrystallized tantalum. This contrasts with the observation that tantalum of norma1 purity is very ductile, even at liquid-nitrogen temperature. Imgram et al. also found that hydrogen additions caused a deterioration of notch tensile properties of tantalum. The purpose of this communication is to present some limited evidence that hydrogen can also cause fatigue embrittlement of tantalum. The material used in this investigation was wrought, stress-relieved (1000°C, 1 hr), are-melted tantalum rod (5/8-in. diameter) containing the following impurities in weight percent: 0.005 C, 0.007 02, 0.0005 H2, 0.003 N2, 0.08 Cb, 0.01 W, and 0.01 Fe. Hydrogen charging was done in an atmosphere of flowing dry hydrogen for 3 hr at 600°C, followed by an homogenizing anneal in purified argon for 15 min at 600°C, and cooling in an argon atmosphere. Typical micro-structures of the hydrogen-free and the hydrogen-charged materials are shown in Fig. 1(a) and Fig. 1(b), respectively. Fig. 1(b) shows the appearance of hydride precipitates which, in many cases, formed preferentially parallel to the rod axis. The hydride dispersion was uniform across the diameter of the specimen. The fact that the precipitate was a tantalum hydride was tentatively confirmed by X-ray diffraction on a metallographically prepared surface. After hydrogen charging, chemical analyses by vacuum fusion revealed the hydrogen content to be 0.0295 wt pct. In addition, the oxygen and nitrogen contents were slightly raised to 0.0095 O2 and 0.005 N2.

Jan 1, 1964

By John R. Freeman

The die pressing of brass may be described as a method of producing irregularly shaped parts of brass and other copper alloys by hot deformation in a die under pressure. Die pressing of brass was first developed as an improvement on sand castings in order to obtain irregularly shaped articles of brass with superior surfaces, a closer tolerance in dimensions, a denser structure, freedom from porosity and elimination of the relatively large amount of scrap invariably attached to sand castings. The freedom from sandy surfaces with consequent greater tool life in machining operations was also recognized as well as elimination of losses due to the uncovering of blowholes in machining operations. Die pressing also gave alloys of superior strength. Die pressings today are made from extruded rod or shapes, according to design of the part to be made. The greater number of pressings are made from round rod, because of its relatively lower cost and ease of handling. The rod is first sheared or sawed into desired lengths, the diameter of rod used and length of "slug" or "rivet" depending upon ultimate weight and shape of the die-pressed part to be made and design of die. The dimensions of the slug are figured so as to give the minimum amount of scrap to be sheared from the pressing as it comes from the die. Extruded shapes having I, T or X sections are often used when the finished part is to have a similar shape or heavy sections are joined by relatively light sections of considerable length. A rod bent in the shape of a U is also used on occasion, for similar reasons. Proper shearing of the slugs is of considerable importance. The sheared ends of the slugs should be as flat and straight as possible. Improperly sheared ends having an angle to the axis of the bar or a rough, uneven surface are liable to give folds or laps in the finished pressing and proportionately high rejections. The property of shearing varies considerably with different alloys and should be considered in the selection of a material for a given part. Where satisfactory shearing is not possible, the slugs may be cut from the bar by power saws. Extruded

Jan 1, 1931

By L. F. Pett

ALTHOUGH Kennecott's orebody has long been outlined, it is still necessary to define further its limits. This mine, long an advocate of churn drill methods, recently supplemented its practice by using a diamond drill. So far, the diamond drill holes have been along the main canyon floor which traverses the mine area. This zone, highly fractured, is cut by numerous friable quartz veinlets encountered within the porphyry. These veinlets, formed by filling contracted porphyry fractures with hot, siliceous, mineral-bearing solutions, are often more highly mineralized than adjacent porphyry. They pulverize on contact, yielding only slight amounts of core. For this reason neither analysis of core recovered (amounting to 37.5 pct of approximately 10,000 ft of hole drilled) nor sludge analysis considered separately would give correct assays. The following equation has been adopted: actual weight theoretical actual weight core — theoretical weight sludge Drilling is done un.der contract. Collection of core and sludge samples together with double-checked assaying is done by the company. Microscopic, specto-graphic, and X-ray examination of rock specimen saved is carried on at the University of Utah. A fund, set up by Kennecott Copper Corp. at the University, has encouraged cooperation in solution of mining research problems. The drill used is a Longyear hydraulic powered by a Waukesha 26-hp gasoline motor. A pump, Bean Royal type, is powered by a 7-hp Briggs-Stratton gasoline motor. Weight of unit is 4000 lb and is placed under tripod of 35-ft wood poles within a 25-ft sq area. The following results have been attained: Avg depth of hole drilled, ft 1215 Avg drilling depth per 8-hr shift, ft 10.11 Core Size, In. Avg depth of NC casing, ft 21 2 11/16 Avg depth of NX casing and size core, ft 178 2Ye Avg depth of BX casing and size core. ft 427 1% Avg depth of AX casing and size core, ft 585 1 5/32 Through the use of metal sludge collection boxes, 12 ft long, 18 in. wide, and varying from 12 to 24 in. in depth, sludge recovery has been maintained above 95 pct. Samples, both core and sludge, are assembled for each sample interval and averaged in 50-ft bench increments. Determinations for mineral values are made at both the mine and mill. Assay results varying in excess of 0.05 of copper assay values are rerun to determine correct assay. The organization chart for the Kennecott Utah copper mine is shown in Fig. 1. The Utah mine requires approximately four men per shovel shift to drill solid rock, properly slope banks, and trim loose material from the top of bench sections in making them safe for men and equipment working below. During recent years, while the mine has been worked day and night, powder crews have worked day shift only. Series of toe holes drilled back of advancing electric shovels comprise approximately 70 pct of all mine drilling. These holes, spaced about 21 ft apart, have a depth of 24 ft. Of the footage drilled, 25 pct is for vertical holes either 24 or 28 ft deep, spaced about 28 ft centers along the top rim of banks. This combination of toe holes, using an Ingersol-Rand DA 35 drifter mounted on a tripod and the vertical holes using an Ingersol-Rand Type X71 wagon drill is standard practice above the pit elevation. These benches are 68 ft high, with a few exceptions, while benches below the pit elevation are 50 ft high and require very little drilling other than toe holes. Five benches, varying in height from 80 to 100 ft, require a combination of toe holes plus vertical holes and bank holes or electric churn drill holes. Bank holes using the DA 35 drifter and electric churn drill using Bucyrus-Erie Model 29T, account for 5 pct of feet drilled. Until the past year, drilling of fill material on upper levels was accomplished by churn drill method. Wagon drills are now used for fills because they can be set up and drill a hole an hour. It is necessary to run an air drill 7 hr for each 8-hr shovel shift. Average drilling rates during the past year were as follows: DA 35 drifter using 2 and 3-man crews — 4.36 ft per man hr X 71 wagon drill using 2-man crews — 6.45 ft per man hr DA 35 drifter bank holes, 3-man crews — 2.53 ft per man hr Bucyrus-Erie churn drill, 2-man crews —1.9 ft per man hr Total mine avg — 4.57 ft per man hr Mine practice assigns powdermen to job locations where they perform all drilling and blasting work within the area. Almost as much labor is consumed in springing and loading holes as in drilling them. Average powder consumption is approximately as follows: Per Electric Shovel Shift, Lb To spring and chamber holes — 50 Blasting — 500 Trim banks — 50 One fifth of all powder used is Hercules hercomite bag powder while four fifths is Hercules gelamite 65 pct strength in 1 Vi in. x 8 in. sticks. Frozen material, overhanging from top banks, creates a winter hazard to shovel operators and equipment. Experiments are being conducted with a high-speed Hercules powder in an effort to eliminate this condition. Banks are trimmed by powdermen who lodge 8 or 10 bundles of powder, containing 15 or 20 sticks each, across the upper surfaces of each working face. To each bundle of powder is attached a primer with 6-ft fuse which is lighted as the powdermen, who have lowered themselves down the bank on ropes, ascend to safety. Three angle dozers, D8 caterpillars, make grades and move supplies for the average 31 drilling machines working daily. Compressed air is furnished by three Ingersol-Rand compressors, each with rated capacity of 3750 cu ft of air per min at 100 lb reservoir pressure.

Jan 1, 1952

By Albert Sauveur

It is delightful to read a technical paper like that of J. E. Johnson, The Effect of High Carbon on the Quality of Charcoal-Iron, presented in October, 1912, at the Cleveland meeting of the American Institute of Mining Engineers.' The clear, simple, and straightforward manner in which he describes his experiments and results makes you feel as if you had been, so to speak, at his elbow during the course of his investigations, while his method of procedure is so rational that you can fairly anticipate each step in the logical sequence of the tests performed. The following notes suggested by Mr. Johnson's paper are presented here in the hope that they may help, if only a mite, towards the final solution of a problem of considerable scientific and industrial importance. Physical Properties of Cast-Iron us. Its Ultimate Composition. Mr. Johnson writes that " an investigation along the lines of consumption showed that different irons have different characters totally independent of their analyses," and he declares that " the presence or absence of these elements [meaning carbon, phosphorus, silicon, and manganese] alone will not account for all, scarcely for a half, of the facts which have long been known." He further tells us that some foundries have " proved, by the most irrefutable tests, that they could take a certain iron of a given analysis and produce certain results," while with " another iron of the same analysis they could not produce these results at all." I feel confident that every experienced and thinking metallurgist will readily believe Mr. Johnson's statements and will share his views in regard to the hopelessness of inferring the

Jan 1, 1914

By D. W. Levinson, L. E. Tanner

DURING the course of an investigation of the zirconium-iron-tin system the zirconium-iron system was reexamined up to 55 pct* Fe. The alloys pre- visible melting3 and X-ray diffraction studies were made of samples of the alloys. The ferromagnetic properties of ZrFe2were determined by Professor P. W. Selwood* using a modified Faraday balance.4 The zirconium-rich portion of the phase diagram is presented in Fig. 1 and compared with the work of Hayes et al.1 The maximum solubility of iron in ß is somewhat decreased while the eutectic temperature is raised. There seemed to be no change in the eutectic composition of 16 pct Fe. Since the base material was so low in iron content, it was possible to establish the maximum solubility in a between 0.017 and 0.025 pct Fe at the eutectoid temperature. The observation of fine ZrFe, particles in the micro structure of a specimen of 0.012 pct Fe alloy quenched from 700°C indicated that the solubility drops below this composition at 700° C and lower. Further study was made of the intermediate phase ZrFe2. wallbaum5 identified the compound initially as ZrFe2 with a C 15 (MgCu2) structure, placing it at 55 pct Fe stoichiometrically. Hayes et al.1 believed they found the phase at about 47.2 pct Fe and called it Zr2Fe3 but reverted to ZrFe, in the discussion of their paper.6 Jordan and Duwez7 confirmed Wallbaum's work as well as finding the same single-phase structure to about 62.3 pct Fe or Zr0-61 Fe2-18. In order to establish the ternary phase relations in the zirconium-iron-tin systema the exact position of this phase had to be known. This was accomplished by X-ray diffraction, visible melting, and metallographic techniques. Elliott8 obtained a single-phase ZrFe2 X-ray diffraction pattern from an alloy of about 55 pct Fe. This was confirmed in the present study with an alloy of 54.81 pct Fe. However, extra lines (attributable to a or ß zirconium) were found in diffraction patterns of the 47.42 and 49.83 pct Fe alloys. The melting characteristics of these same alloys were studied by suspending 47.42, 49.83, and 54.81 pct

Jan 1, 1960

By Frederick Laist

AFTER a series of experiments covering a period of about three years, ending from the spring of 19iJ.2 to the spring of 1915, a 2,000-ton leaching plant for the treatment of the accumulated copper concentrator tailing was built and put into operation. During the experimental period, the first step was that of laboratory experiments or beaker leaches. The results on this small scale were so satisfactory that a small operating plant, capable of handling 5 tons of roasted tailing per day, was installed. Again, the results proved satisfactory and an 80­ton plant was built and operated continuously from August until February, 1913. In this plant, full-sized roasting and leaching units were

Jan 8, 1916