Search Documents

By J. W. MacDonald

Review of equipment, performance, and shaft design plans including head-frames for sinking and forms for lining are given. Also included are comparative data for shafts of 11 x20 ft and 193/4 x 30 ft with 756 and 666-ft depths, respectively. Advantage from curtain wall installation with "slip forms" which warrant consideration for normal lining are outlined. A preliminary review is also made of "chemical grouting" to stop water inflow leakage with Halliburton equipment and service. Two coal mine shafts recently completed in Franklin County, Ill., afford experience and accomplishment to warrant review. These shafts provide access to a tract with a potential recovery of one hundred million tons. This work provided the initial sinking by other than a contractor's organization since 1918. Four additional shafts required during the interim were sunk under contract arrangement with others. Supervisory contact and inspection afforded experience to govern planning and conduct of the recent work. TEST DRILLING Core test holes were drilled within each of the two shaft locations. Four additional cable tool holes were drilled on a radius of 700 ft from the shaft bottom to determine the coal seam elevations and govern the underground layout plans for each shaft. A graphic log of the hoist shaft test drillhole is shown by Fig. 1. A very soft sandstone was found at a depth of 16 ft. Cored recovery of the sandstone proved much weaker than the overlying compacted sand secured with coring facilities for soil recovery. Gradation from the very soft sandstone to fairly hard material occurred with the next 14 ft, extending to a depth of 30 ft. The weak character within the upper portion entailed need of adequate protection when sinking as described later. A part of the sandstone provided sufficient porosity and permeability to warrant further investigation. Adjacent cable tool drilling for temporary water supply disclosed inflow was limited to 2 gpm with a depth of 40 ft. It was increased to 12 gpm during the next 50 ft of drilling and occasioned subsequent precaution when sinking. General arrangement of facilities for sinking the hoist shaft is shown by Fig. 2. An available steel frame building was used to accommodate the hoist, compressor, shop, and shower or change room. The stiff leg derrick with 90-ft length of boom permitted removal of forms from the wood shop to the storage area or delivery within the shaft. Reinforcing steel and other needs were similarly handled, in addition to headframe erection. The headframe was placed over one end of the shaft to enable passage of forms for lining through the adjacent half next to the stiff leg derrick. The steel headframe as shown by Fig. 3 was fabricated locally. Side anchored cables from the

Jan 1, 1961

Joseph W. RichaRds, South Bethlehem, Pa. (communication to the Secretary*): The hold experiment of Mr. James Gayley in drying the blast used in the Isabella furnace has attracted the attention of the whole metallurgical world, and has given rise to a wide discussion of the reasons for its great success. Mr. Gayley and the capitalists who backed him in his work deserve congratulations on the success of the venture, not only because it succeeded, but because they have been rewarded far beyond the maximum that could be expected from theory or probability. To state the case in its simplest terms, all that could have been predicted was: (1) that the removal of the moisture from the blaet would result in the saving of the heat required for its decomposition, representing from 3 to 5 per cent. of the heat-value of the coke used; hence about that quantity of fuel might be saved; (2) that the furnace would be somewhat more independent of variations in the weather; (3) that the campaign would be a little hotter; and (4) that the speed of the blowing-eugines would be decreased, at least in amount proportionate to the reduction in temperature of the air led to them. I do not think anyone anticipated a much larger output per day. The results actually attained were: (1) the furnace made an increase of 24.86 per cent. in the output of pig-iron per day; (2) it consumed 19.6 per cent. less coke per ton of pig-iron made; (3) the blowing-engines were run 15.8 per cent. slower; and (4) the saving in power made up for the power required to run the refrigerating-plant. In addition, the blast was hotter; the waste-gases cooler, because of their smaller volume; and there was a greater proportion of carbon dioxide to carbon

Jan 1, 1906

By R. W. Parsons

The over-all apparent single-phase permeability of fracture-rock systems was studied using two different two-dimensional models. In a strict sense the results are applicable only to these models, yet may give some insight into real reseruoir behavior. The regular fracture-matrix model can have any number of regular fracture sets. All fractures within each set have the same orientation, width and spacing. The gross behavior is amlytically equivalent to that of an anisotropic permeable medium. In the heterogeneous fracture systems, individual fracture conductivities vary within a two-dinensioml network pattern. A computer program calculates the overall permeability after the conductivities are randomly placed in the network. The calculated permeability depends upon the distribution of these conductivities and the particular fracture pattern into which they are placed. Although detailed information on actual reseruoir fracture systems is not available, this study shows how some of the possible variables may affect obserued gross reservoir characteristics. INTRODUCTION Characteristics of reservoir rocks are determined by direct (core analysis) or indirect (logging and production tests) examination. Both methods, singly and together, are widely used in reservoir evaluations. For fractured reservoirs a problem exists in relating characteristics of cores to the in situ reservoir properties. Knowing fracture characteristics can be of value in determining production mechanisms. Because of the limitations of observation, the intimate details of a fractured rock system will never be known. One approach in analyzing fractures is to study the behavior of some conceptually simple models. The two models analyzed contain features which may be realistic, yet are mathematically tractable. Flow is considered in two dimensions only, with the plane of interest at right angles with the fractures. This concept represents the horizontal flow in a reservoir system with the fractures oriented vertically. Only single-phase, laminar flow is considered. The regular fracture-rock system permeability is calculable from a simple analytical expression. The heterogeneous system requires a computer program for calculating overall permeability.

Jan 1, 1967

By Paul F. Kerr, Donald M. Hausen

Fine colloidal gold near Carlin, Nevada is disseminated in leached carbonate strata of the Roberts Mountains Formation in the Lynn "window" of the Roberts Mountains thrust fault. The ore body is generally stratiform and is more or less conformable to altered beds near the top of the formation, underlying Devonian limestones. Two sequences of mineralization are recognized: ( 1) an earlier base metal-barite assemblage related to early Cretaceous intrusives (121 ± 5 m.y.), and (2) a later low temperature Au-As-Hg-Sb assemblage of near surface emplacement. The earlier sequence consisting of sparse galena and sphalerite in barite with anomalous amounts of zinc, lead, nickel and copper, associated with dikes of dacitic composition, is of little economic importance. The later sequence of gold, realgar, cinnabar, and stibnite associated with extensive silicification and argillic alteration of limestone beds, has resulted in important deposits of gold. Argillic alteration of hydrothermally leached carbonate strata has provided the environment in which the most prominent gold deposition took place. Carbonate minerals in the limestone host rock have been replaced by microcrystalline quartz and chalcedony to form stratiform silica masses and recrystallized lenses of euhedral quartz. Zones of porous silicification are light gray to white, elliptical in shape, and more or less follow bedding. Silicification is bordered by argillic alteration and pyritization. Deposition of gold usually lies in a zonal pattern that encircles chimney areas of silicification.

Jan 1, 1968

By H. C., Simpson

MANY metals by virtue of their place of occurrence as ore, and their uses are travelers! Iron and steel, for instance, is one of the greatest of travelers in the form of ships and the romance of iron in this respect is only just beginning to be superseded by the stories which can be told of the travels of aluminum and its alloys, used in the building of airplanes. Tin is a traveler from the Straits Settlements to this country and Europe, for use in the canning industry; afterward traveling all over the civilized world as a part of the container for preserved foods. Silver is somewhat of an aristocrat, when its uses are measured against those of the baser metals. From earliest times it has been used for adornment (first perhaps o4 the person and later for the embellishment of weapons and' buildings), for the making of fine ar¬ticles used in the household, and as money. While its uses have been widened by the discoveries in chemistry, electricity and other sciences, its early uses are still much in evidence in our modern life.

Jan 1, 1928

By Charles Jackson Abrams

MINING is one of the major industries of the Rocky Mountain region and since the United States became involved in the present World War, all mines have been called upon by the Government for the maximum production of the strategic metals necessary. Operating under the most adverse conditions, such as priority requirements, slow delivery of necessary material and equipment, labor shortages, and freezing of all wages, which still permitted some industries to pay higher rates than were allowable in the mines, thereby drawing labor from the mines; and the United States Employment Service continually giving mine labor certificates of availability; these and many other problems made mine operation particularly difficult. Yet, in spite of these obstacles, the mining industry, either through its own resources or through Government subsidies in the form of loans or premium prices for strategic metal, have and still are making an all-out effort to meet Government demands. They, without question, have played a major role in assisting the war effort.

Jan 1, 1945

By C. W. Goodale

TOMBSTONE, a name not exactly full of cheerful suggestion, has a great record as a mineral producer and a colorful history as a frontier mining camp. The only practical route to Tombstone in the early 80's was by way of San Francisco and Los Angeles. The Southern Pacific was building across Arizona, and a sleeper was attached to a construction and freight train at Los Angeles, and was trailed slowly across the Colorado Desert to Benson in the San Pedro Valley. Thence one staged 26 miles to Tombstone, which is located near the foot of a range of hills at an altitude of about 4500 ft.

Jan 1, 1925

By J. R. Campbell

THE need for standardizing methods of arriving at definite conclusions regarding the cleanability of a given coal, and for measuring the performance of coal-cleaning equipment, is constantly increasing. Earlier notes by the author on this subject are amplified in this paper, because he believes that better preparation of bituminous coal is a partial solution of the coal operators' troubles. WASHABILITY STUDIES The term "washability" of coal was coined when washing was the universal method of separating coal from its impurities by utilizing their difference in specific gravity. This and analogous terms are still used in their broad sense although pneumatic or air separation is now used to clean coal. These terms are so used in this paper. Too much time or money, can hardly be spent on "feed surveys" to get a "picture" of the coal that is to be cleaned. There have been too many "rule of thumb" methods used. Screen analyses and "sink-and-float" tests on the raw coal enable the coal operator and washery man to predict within reasonable limits the results that may be expected from any efficient cleaning apparatus.

Jan 1, 1928

By J. M. GLEDHILL

IT would doubtless have been felt by many but a few years back that there was little left to be said on the subject of crucible tool-steel, and that something akin to finality had been arrived at in its manufacture and general treatment. Probably such feeling was justifiable when it is remembered that the making of steel in crucibles is by far the oldest method known, dating back from time immemorial, it being indeed impossible to accurately trace its origin and earliest development; but it seems certain that carbon-steel was made and used thousands of years ago for cutting-tools. Proof of this may be seen by the marvelous carvings and workings on the intensely hard stone-work of the ancients, for it would be difficult to conceive by what means, other than with steel tools, such work could have been executed; and it is wonderful to contemplate that steel cutting-tools should have been used so long ago, whilst the principle of manufacturing them-that is, by fusion of iron and charcoal in crucibles-was then in a measure on the sane lines as we work on at the present day. Archaeologists have discovered that the Chinese made steel in crucibles long before the Christian era. " Wootz " steel fabricated in India centuries ago was crucible steel, as was also the celebrated Damascus steel, produced at the forges of Toledo, and, curiously, this latter steel furnishes' yet another proof that "There is nothing new under the Sun," for it is recorded that Damascus steel contained certain percentages of tungsten, nickel, manganese, etc., some of the very elements, in fact, contained in the present modern high-speed steel, so that a latent high-speed steel may be said to have existed

Mar 1, 1905

By Basil B. Zavoico

The production of all Russian fields incressed from approsimatctly 74,000,000 bbl. during 1926-27, to approximately 83,000,000 bbl. during 1927-28. Of this amount Baku was responsible for 54,.500,000 bbl., Grozny for 25,800,000 bbl., and Emba for 1,200,000 bbl. Accordingly, the proportional importance of the Grozny oil field has been considerably increased, the present production being twice that of 1913. The most notable factor of production during 1927-28 was the importance of gushers; 40.8 per cent. of the total was thus obtained. In the Baku fields 26 per cent. of the total, and in Grozny 74.2 percent'. of the total were produced by naturally flowing wells. This may be explained by the reduction in authorizations for drilling by the central authorities, and, accordingly, the local trusts increased the production to the planned figures at the expense of the proved prolific reserves. In Baku region, the Surnkany oil field produced 36.1 per cent. of the total Baku production, or an equivalent of 53,800 bbl. per clay, the largest percentage coining from the fifth horizon. Nest year's plans call for continual development of that horizon as well as of the sixteenth horizon in the Bibi-Eibat field, which was opened lately. In the Grozny fields the New Area (Bellik) WAS responsible for 79.4 per cent. of the total production. The authorized plan for 1928-29 production calls for 92,200,000 bid., and a reasonably accurate estimate for 1932--33 production is placed at. 156,000,000 bbl., with Baku contributing 101,800,000 bbl., Grozny 44,100,000 bbl., Emba 6,200,000 bbl., Kuban 2,100,000 bbl., Saghalien Island 1,400,000 bbl., and Russian Turkestan 400,000 bbl. In connection with recent discoverices in the Baku area these figures art. quite conservative. The average production per well per day in the Baku oil fields was 49.2 bbl., in Grozny 175 bbl.; in detail, Surakany oil field averaged 250 bbl., and the New Area in Grozny 514 bbl. per day. New completions in all Baku fields averaged 264 bbl. per day, and in Grozny 970 bbl. pel. day. These figures show a considerable progress in the technical developnlent of all fields, compared even with the prerevolution figures, since all the mprovements are noted in the fields that arc over 30 years old.

Jan 1, 1929

By H. H. Bein

Most western industrial sands are feldspathic and contain feldspars in variahle amounts. A few deposits will show alumina contents of less than one per cent while others will contain over twelve per cent alumina. Some industries are not especially concerned with the amount of contained feldspar but are interested only in color and in size gradations. Other industries, however, are very much interested in alumina content and set up quite rigid specifications as to this content. Several western plants are beneficiating crude sands both to reduce the iron content and to control the feldspar content. At present, most of these plants are using flotation processes for both controls although a few plants do use magnetic separators for the reduction of iron content. Some work has also been done with electrostatic separators for the feldspar-quartz splits. The Sand Division of Del Monte Properties Company, Pebble Beach, California, has been operating a flotation plant for iron removal and the separation of quartz and feldspar since 1950. As mentioned before, control of alumina, especially in the quartz product, is very important. Some users require an alumina content of less than two per cent and others will demand a product of less than one per cent Al2,O3,. The standard Quinolate method for determining alumina is lengthy and time consuming. The HF —H2SO4 evaporation step is especially critical and, if forced, spattering is apt to occur with a resulting loss of sample. Standard procedure is to evaporate to dry ness overnight at a low temperature. Even with forcing under optimum conditions the procerlnre will take two or three hours to complete. A new method has been developed which allows an alumina determination to be made, in 10 or 15 minutes, on a sample of the quartz product as it is being produced. This pocedure, although simply an approximation, has been most helpful in showing whether or not the product being formed is meeting specifications. This procedure has also allowed a great reduction in samples formerly taken and analysed by the orthodox method. Whether a sample assays 1.75% A12O3, or 1.95% .41,0, is not so important as the fact that it is below the allowable maximum of 2.00%. Similar thinking would apply to products required to contain less than 1.00% A1,0,. The step by step procedures for the method are as follows: 1. Collect sample, drain or filter, and dry. 2. Split sample through standard Jones sample cutter to quarter or eighth sample, depending on size of original sample taken, then split down to about 5 grams through Sepor micro-splitter. 3. Screen through 50 mesh sieve (U.S. Series) and reject undersize. 4. Weigh out 2 grams and place in platinum crucible. 5. Etch with 3-5 mls 38.40% HF for 1 minute at room temp. 6. Decant and wash. 7. Stain for two minutes in same crucible with a 1% water solution of Nigrosene dye. 8. Decant and wash well. 9. Dry.

Jan 1, 1961

By John Nunes, Frank R. Larson

Temperature-dependent functions of various ten-sile flour stress and fracture parameters were investigated on iron and low composition alloys of Fe-C, Fe-Cr, Fe-Mn, and Fe-Ni. Data were obtained over a range of test temperatures from 200" to -196"C at an initial strain rate of 0.01 min". It was found that the strain-hardening exponent, n, for the Fe-Ni alloys increased significantly at very low testing temperatures with increased alloy addition. Also, the stress and strain at fracture followed a predictable transitional type of behavior. The flour stress-temperature dependence was evaluated employing the relation: M where it is shown that composition can strongly influence the constant M. An empirical formula describing this effect is as follows: M = MI (equivalent at. pct Ni)-'" Some preliminay, tests were run on several commercial steels to test the generality of this relationship. One of the phenomenological explanations of the ductile-to-brittle transition encountered in bcc metals is based upon the difference in the temperature dependence of the flow and fracture stresses.' It states simply that the fracture stress is relatively insensitive to temperature and that the yield or flow stress rises rapidly with decreasing temperature so that, when the flow stress reaches the fracture stress, brittle fracture occurs without appreciable plastic deformation. This behavior is illustrated schematically in Fig. 1 where the ductile-to-brittle transition is shown to occur at two possible temperatures. The lowest temperature, TB, represents essentially completely brittle behavior while the higher temperature, TN, represents "notch" brittle behavior. Support for this theory is obtained when it is observed that fcc metals, which do not commonly have a ductile-to-brittle transition, also do not commonly exhibit any strong temperature de- pendence of the yield stress. This relationship of yield or flow stress behavior with the ductile-to-brittle transition has been generally observed for most metals representative of these two crystallo-graphic structures. One exception to this generalization appears in the case of tantalum where no apparent ductile-to-brittle transition has been observed. However, this may simply be an indication that this type of behavior is not directly related to the flow stress and that some other mechanism such as twinning must also be operative. A comparison of the typical temperature dependence of the yield stress of some representative metals is shown in Fig. 2. In the study of the temperature dependence of the strength of metallic materials, considerable ef-

Jan 1, 1963

By H. C. LIVINGSTON

At the Hanna No. 4-A mine of The Union Pacific Coal Co. a new system of trackless mining is being utilized to extract a 26-ft coal seam. By using shuttle cars and a conveyor belt for haulage in the rooms and panel entries instead of pit cars and panel hoist a saving of 12 cents per ton is expected. Mining is conducted in a 26-ft coal seam laid down on a synclinal structure with active workings on a pitch of approximately ten to twelve degrees. The coal seam is interbedded between a shale bottom and sand- stone top. The coal is friable, high in moisture, and subject to spontaneous combustion. The mine is rated gassy by the State Coal Mine Inspection Department. Mining is conducted at the present time by unbalanced rope haulage an main slopes spaced on approximate 4300-ft centers with the three-entry system driven to boundary lines, strike entries being turned on approximate 1300-ft centers. Panels are driven to the rise between entries at approximately 750-ft intervals with panel rooms driven on the strike 500 to 600 ft long, leaving 150 ft of barrier pillar between each block of panel rooms.

Jan 1, 1949

By P. H. G., Durville

ANY metal which contains even a small percentage of aluminum possesses certain peculiarities of appearance and properties which are exhibited both when the metal is melted and after it solidifies. Pure aluminum, or an alloy containing a small proportion of aluminum, can be melted without flux-except for a layer of charcoal-because a film of aluminum oxide and metal forms at the surface of melted aluminum. Although very thin, this film is air-proof, and it prevents the metal underneath from oxidizing. This oxidized film does not move easily on account of its toughness and high surface tension. One very important point in connection with this process of still casting has not been strongly enough stressed, namely, that the same kind of surface film with the same peculiarities forms over the surface of all melted alloys that contain even a small proportion of aluminum. Experienced foundrymen know how desirable it is to cast aluminum under its "skin" or under the surface of the film which tends to remain still. In the case of red copper, when in fusion, the surface shows pure copper only. This' is due to the fact that liquid copper constantly absorbs the copper oxide which forms on the surface. By closely examining melting copper the oxide can be seen dissolving in the bath, and going into solution just as pulverized sugar dissolves in water. When copper is cast in the open, either in wire bars or cakes, the surface of metal exposed to the air is covered by a film of black oxide that cannot be absorbed by the metal.

Jan 1, 1927

By J. L. Gregg, J. L.

RECENTLY there has been considerable interest in the production and use of extra hard alloys composed primarily of tungsten and carbon. Dr. Hoyt's recent paper1 gives a good description of these alloys and describes their performance when used as tools. There are a number of these alloys on the market sold under various trade names, and it is the purpose of this paper to describe the results of an investigation of the structure of five of these alloys by means of microscopic and X-ray methods. The samples studied were in the form of small tools or wire-drawing dies, which were either purchased or supplied as samples. They were in some cases not supplied by the original makers but were furnished by the agents in this country, and we wish to call attention to the fact that they may not be truly representative of the materials supplied under the various trade names. No performance data are given and no inference as to the inferiority of one alloy as against any other is made. K. Schröter2 recently described methods for polishing alloys of this type for microscopic examination and has presented photomicrographs of several alloys. However, he did not identify their constituents or describe methods for their identification.

Jan 1, 1929

By E. V. Potter, H. C. Lukens

THE volume of hydrogen released from electrolytic manganese at various temperatures and pressures was determined in a previous investigation1 as part of a study to determine the most practical procedure for removing the hydrogen from electrolytic manganese metal. No attempt was made to determine the absolute volume of gas in the metal at any temperature and pressure; the volume of gas released showed only the variation in solubility with temperature and pressure. The results were very similar to those obtained by Sieverts and Moritz.2 Both sets of data show a minimum solubility between 500° and 700°C., but they differ in certain respects; on cooling from 500°C., our results showed an increase in solubility of about 7 C.C. as compared with an increase of 34 C.C. per 100 grams shown by Sieverts. Furthermore, the transition temperatures, as indicated by sharp breaks in the solubility curves, did not agree well with Sieverts' data. This information was of secondary importance in the earlier investigations, and the solubility at low temperatures and the transition temperatures were subject to considerable error. There- fore, a subsequent investigation, reported in this paper, was made to measure the absolute solubility at temperatures from room temperature through the melting point and make more accurate observations of the transition temperatures. APPARATUS AND METHOD The apparatus and method were essentially the same as those described in the previous work,1 as shown in Fig, I. At high temperatures, the small tube containing the thermocouple in the sample container A frequently broke off, so for some of this work the thermocouple was placed outside the sample container and protected by a quartz tube of about the same wall thickness as the sample container. No significant difference was found in the transition temperatures obtained in the two ways. The automatic temperature controller was used in these tests in the regions where there was little change in solubility with temperature. In the neighborhood of the transition points a continuously variable autotransformer was used instead of the automatic controller, and the power input to the furnace was adjusted so that the temperature increased or decreased at a very slow, uniform rate through the transition range. This procedure was followed because the temperature oscillations produced by the controller were too great compared with the transition range, and the transition points determined under such conditions were less accurate. ABSOLUTE SOLUBILITY Procedure and Results The absolute solubility of hydrogen in manganese could be determined most

Jan 1, 1946

By David Cole

THE appearance of the Wilfley table in 1897 marked an epoch in the art of concentration of ores. The table has merited and received an almost unprecedented measure of public approval, lasting through its whole patent life. It has been very little improved in itself, or improved upon by competitors. The new machines bidding for popular favor have been of the Wilfley family, but without ability to do markedly better work than the parent m:-chine, or to (to more work except by the use of superimposed decks, the latter having obvious disadvantages. FIG. 1.-The- Butchart RIFFLE System. During the past three years there has been developed at Morenci a new type or arrangement of riffles applicable to the Wilfley type of concentrating table which corrects many of the objectionable features or limitations of the older system and obviates most of the difficulties encountered with it, particularly when handling ores having a low ratio of concentration. The new type is known as the Butchart1 riffle system, and its general arrangement is shown in Figs. 1 and 2.

Jan 2, 1915

By T. J. Koppenaal, M. E. Fine

A yield point effect attributed to short-range ordevi?g (SRO) occurs in Cu base Al. At at 296°K varies with heat treatment, decreasing as the annealing ternperature is raised .from 433Oto 598°K. Davies aid Cahn' observed a corresponding decrease in SRO. (523 °K anneal, measured at 77°K) is approximateZy proportional to the variations of A7 with strain rate and testing temperature are also Consistent with the idea that is associated with SRO. A preliminary investigation of the tensile properties of a Cu-Al single crystals showed the presence of a rather strong yield-point effect (drop in flow stress after initial yielding). The object of this research was to investigate its origin and behavior. a Cu-Al alloys are particularly interesting because diffuse X-ray scattering measurements by Davies and Cahn,' Houska and Averbach,' and Borie established the presence of short-range order. The degree of local order may be changed with heat treatment.' cottrel14 suggested that the presence of local order might result in a yield-point effect, and thus the possibility exists here for experimentally ascertaining the importance of short-range order with respect to yield points in these alloys. Since a 12 pct difference exists between the atomic sizes, elastic or Cottrell locking5 must also be considered. Further, Howie and swanne have shown that the stacking fault energy of copper is reduced by aluminum additions. The width of extended dislocations should thereby increase. hus the conditions appear attractive for Suzuki locking.' Finally, the possibility of stress-induced order at dislocations, schoeck locking,' must also be examined, EXPERIMENTAL PROCEDURE Alloys up to 14 at. pct Al were prepared by induction melting high-purity (99.999 pct) Cu and (99.996 pct) Al in a graphite boat under a dynamic vacuum of 5 X 10o mm of Hg. After homogenizing the ingots at 900°C for at least 24 hr under vacuum, they were rolled with intermediate anneals to strips 1.55 mm thick. Single crystals 10 in. long were grown by lowering strips, contained in a split graphite mold sealed in fused quartz at 5 X lo-' mm of Hg, through a single coil induction heater at a constant rate of 1/2 in. per hr. Tensile specimens 1.25 in. long were cut from the single crystal strips and reduced cross sections about 0.7 in. long and 3.0 to 3.5 mm2 in area were introduced by filing and abrading.8 To remove the worked portion about 10 pct of the cross-sectional area was removed by etching. Back-reflection Laue photographs of a filed and etched specimen were taken before and after annealing at 900°c for 24 hr. Small, well defined Laue spots were obtained with no visual difference in the two photographs. Further, specimens with and without the reduced sections began yielding at about the same stress. Hence, for our purposes, filing and abrading did not affect the structure of the specimens. Each single crystal specimen was annealed at 900° c in vacuum for at least 24 hr and furnace cooled; while cooling through the range of 250o to 200°c, the rate was about 55°C per hr. Orientations were determined by the usual back-reflection Laue

Jan 1, 1962

By Frederic Benard

PRIOR to 1936, the Ontario Refining Co. received all incoming blister copper from The International Nickel Company's smelter in the usual form of 460-lb. cakes, or slabs. These were received in open cars in lots of 250 pieces. At the refinery the cakes were unloaded onto narrow-gauge cars, for convenient handling and pickup by charging cranes. In March 1936, an investigation was started on the feasibility of transferring converter copper in the molten state from the smelter to the refinery anode furnaces, a distance of 1 ¼ miles. Although common in steel practice, the transportation of blister copper in this form had not previously been attempted and a preliminary study of the various factors involved was therefore necessary. For this purpose, a series of experiments was made in which molten copper, removed at different stages during the furnace cycle, was held in a small portable holding furnace. This vessel was essentially a refractory-lined steel cylinder provided with ports for filling and emptying, heated by an oil burner. Dimensions of the steel shell were 3 ft. 10 in. diameter by 7 ft. 3 in. long, and thickness of refractories depended on the design and combination used for the particular experiment. The vessel was filled with approximately 2 ½ tons of copper at a predetermined temperature, the lining having been preheated to a definite point by means of an oil burner. All openings were well luted and temperature readings were made every 15 min. by means of an immersion-type thermocouple. In this manner the rate of heat loss resulting with different refractory design could be developed. The ratio of exterior surface to weight of metal was taken into consideration in comparing the experimental results with what might be expected for a full-sized unit, and observations were also made on type and degree of slag accretion. It was not possible to get as much information on this latter point as desirable, but all evidence showed that the problem would be control of slag build-up rather than attack on refractories. From the information derived, and in consultation with the engineering staff of the supplying company, an order was placed for the first

Jan 1, 1938

By Ellsworth Daggett

In the first paper on the Russell process presented by Mr. Stetefeldt, in May, 1884 (Transactions, xiii.), the process was treated from a purely theoretical standpoint.. 111 his second paper of October, 1886 (Transactions, xv,), the details of the plant, the chemicals used, and the manipulation in both mill and laboratory were treated. The aim of the present paper is to present economical results recently attained, new data affecting the preparation and manipulation of ore in the mill, and a more complete and systematic scheme of laboratory work. This paper is compiled mainly from Mr. Russell's notes of his own experience. Many of these notes, particularly those relating to work at Cusihuiriachic,* Mexico, have been upon work directly under the personal observation of the compiler, who takes pleasure in thus presenting to the Institute, data and considerations of much interest and value pot only to users of the Russell process, but to mill men generally. The description of the chemicals used and of the preparation of the mill-solutions being' in part the same now as when Mr. Stetefeldt's second paper was published, some use is here made of portions of that paper. No theoretical matter is here given. For a treatise containing also the theory of the process the reader is referred to Mr. Stetefeldt's complete work on " Lixiviation of Silver Ores by Hyposulphite Solutions," now in preparation. To facilitate the consultation of this paper, the following synopsis and index is prefixed. The figures in parenthesis indicate the page of this paper on which the subject is treated.

Jan 1, 1888