Search Documents

By J. A. Fellows, Earnshaw Cook, H. S. Avery

TEe increased use of heat-resistant alloys (26 per cent Cr, 12 per cent Ni; 16 per cent Cr, 35 per cent Ni; 12 per cent Cr, 60 per cent Ni; etc.) in recent years has been accompanied by continued demands by the consumer for improvement in properties. The manufacturers of these materials, of necessity, have resorted to more critical studies of the basic causes of variations in fundamental properties. To keep pace with the need for augmented information, previous techniques of investigation have been refined and new test methods and instruments created. It is the purpose of this paper to describe the apparatus, experimental technique and precision of measurement that were employed in the exploration of properties of heat-resistant alloys presented in a companion paper. The detailed precautions in experimental procedure essential for attainment of accurate and comparable data at elevated temperatures cannot be too highly emphasized. The Creep Test Since the fundamental concepts of creep testing have been recognized for the past 20 years, present interest is restricted to refinements in equipment and experimental procedure. The creep-test iaboratory constructed for the American Brake Shoe and Foundry Co. is designed to permit I000-hr. tests in the temperature range of I200° to 2 200°F. with a choice of applied stress extending from jo to 50,000 lb. per sq. in. in increments of 50 lb. per sq. in. To simplify the calculation of weight combinations, the loading beams (Fig. I) are provided with counterweights to eliminate the tare. The precision of the knife-edges (10:I ratio) is such that a 10-gram weight placed on the upper specimen grip will be exactly balanced by a I-gram weight attached to the loading shackle. Check of the loading weights proved the maximum error to be 0.06 per cent. Axial alignment is provided by crossed knife-edges in the grip seats. The furnaces are similar in design to those of Crane and Company, Battelle Memorial Institute, and the U.S. Steel Corporation. An 80 per cent Pt, zo per cent Rh No. 19 B. and S. gauge wire is used as the heating element. The details of -construction are shown in the radiograph reproduced in Fig. 2. The windings are held in place on an alundum tube with aludum cement; the distribution of turns is adjusted to give a maximum temperature gradient of , I°F. over a 4-in. gauge length (Fig. 3). To avoid sharp temperature differentials at the ends of the test section, the length of the furnace is four times the gauge length. Sixteen-inch coupons are used „ to reduce the temperature of the threaded joints and thus to facilitate removal from the grips. Thermal losses are minimized by refractory insulators cut to shape and surrounded by diatomaceous ear,th. The taps

Jan 1, 1942

By M. J. Spendlove, H. W. St. Clair

The problem frequently arises, particularly in refining metals or smelting scrap metals, of separating metals in the metallie state. Many metals may be separated by taking advantage of their difference in vapor pressure. Such separations can be made at atmospheric pressure, but the separations are much more selective and can be carried out at considerably lower temperatures if the distillation is done at pressures of a few millimeters or less in an evacuated enclosure. Until recently, this has not been considered feasible as a metallurgical operation, but the recent improvemcnts that have been made in vacuum technology have broadened the applicability of vacuum processes and have prompted re-examination of low-pressurc distillation of metals as a practicable process. The distillation of zinc from lead is one separation that has already been reduced to practice.l This paper is the first of a series of studies being made on separation of nonferrous metals by distillation at low pressures. Although these experiments were confined to the separation of zinc from aluminum, the significance of the results is by no means confined to these two metals. The purpose has been to investigate a metallurgical technique rather than merely to devise a means of separating specific metals. The experimental work on distillation of zinc from zine-aluminum alloys at reduced pressure grew out of earlier work on distillation at atmospheric pressure.2 The earlier work indicated that it would not be practicable to decrease the zinc in the alloy much below 10 pct owing to the high temperature required. Therefore attention was turned to distillation ah low pressures, at which lower temperatures are required. After preliminary tests were made in a small, evacuated tube furnace, a larger furnace having a capacity of 100 to 150 Ib of metal per charge was constructed. Distillation tests were first made on pure zinc and then on aluminum-zinc alloys of various composition. Particular attention was given to the limit to which zinc could be reduced in the residual metal. Data were also taken on the rate of evaporation, and heat balances were made for both the crucible and the condenser. Distillation Furnace The vacuum-distillation unit is illustrated schematically in Fig 1. The major components are the induction furnace, the condenser, the vacuum system, and the power-conversion unit. Power is supplied to the induction furnace from a 50-kw 3000-cycle motor-driven alternator. The pressure in the furnace is reduced by a vacuum pump having a nominal pumping speed of 10 liters per sec. When in operation, the metal vapors travel upward from the furnace to the water-cooled condenser where they are collected in amounts of 50 to 100 lb. The condenser is removed with aid of an electric hoist. When the system is under vacuum, the condenser is made self-sealing by a rubber gasket between the smooth-faced, water-cooled flanges at the top of the furnace and the bottom of the condenser. The pressure of the atmosphere is more than sufficient to insure sealing. At the conclusion of an experiment, the residual metal can be removed from the furnace by removing the condenser and tilting the furnace with the electric hoist. The metal was cast into the molds carried on a mold truck. A photograph of the furnace and auxiliary equipment is shown in Fig 2. The details of the vacuum furnace are illustrated in Fig 3. The furnace proper is made vacuum-tight with rubber gaskets placed at each end of a fused quartz cylinder. A clamping plate at the bottom and a ring at the top are made to squeeze the rubber between the metal and the end of the quartz tube. A large graphite crucible placed inside the quartz cylinder is thermally insulated and physically supported by refractory insulating bricks. A thermocouple in a quartz protection tube is located at the bottom of the crucible: the leads pass through a rubber seal in the bottom plate. The supporting structure for the furnace is an angle iron frame with transite board sides. The condenser is made in the form of a water jacketed cylinder with an opening to the vacuum line at the top. The bottom has a projecting skirt inside the machined flange to provide additional cooling for the rubber gasket. Condenser sleeves are made in the form of two semicylindrical pieces of sheet metal that fit snugly inside the cooling jacket. The split sleeve facilitates removal of the condensate. Measurement of Temperatare and Pressure The metal temperature was measured by a platinum-platinilm rhodium thermocouple inserted in a well extending up into the bottom of the graphite crucible. During rapid evaporation there is a wide difference in temperature between the surface and the main body of metal in the crucible because of the large amount of heat that must be conducted to the surface to supply the heat of evaporation. The heat of

Jan 1, 1950

By Wallace E. Pratt

UNDER the stimulus of war psychology the American public has grown confused and jittery in its thinking on the subject of this nation's petroleum resources. This confusion arises from the failure of the average citizen, and even of many leaders in government, in our armed forces, and in the petroleum industry itself, to distinguish between our proved reserves of petroleum in the several oil-producing states and the total petroleum re- sources available to this nation. Leaders and public alike examine the accepted estimates of our proved reserves and thoughtlessly conclude that these estimates represent the total of our petroleum resources. Our fears are aggravated if we turn to the statistics on oil-finding and observe that the discovery of new reserves has waned decidedly in recent years. This confusion is dangerous because, under its influence, ill - considered policies spring up and flourish, choking out the most valuable fruits of the long experience of the American petroleum industry.

Jan 1, 1944

By Robert Adams

Secondary or scrap materials appear at all stages in the industrial process and in a bewildering variety of forms, grades, and values. It is useful to begin analyzing them by dividing the broad concept of "Secondary Supply" into three parts First, the concept must encompass the stock, or pool, of secondary materials. In the process of satisfying his wants, man produces desired products from the materials and natural resources found around him. As long as the rate of production is greater than the rate of obsolescence of a given product, the total stock or pool of materials embodied in that product will increase in size This stock concept relating to secondary materials is directly analogous to the "resource" concept used for primary raw materials in the preceding chapter, and includes all materials embodied in existing products (Obviously, this excludes those materials which are destroyed in the consumption process, viz , fuel oil burned to provide heat.) Consumption of a primary material in a productive process tends to reduce the resource base of that primary material In direct contrast, however, the production or use of products increases the resource base of the secondary material. Thus, we find that a country which has no resource of a primary material can, by importing products that contain the material, build up a large enough stock to provide a basis for secondary recovery. The estimated growth of the pool of copper in use in the United States through 1967 is shown in Table 5.B.1.a The estimate of 39 3 million tons at the end of 1967 includes only technologically recoverable copper and is, therefore, somewhat less than the stock concept described previously, which does not distinguish between recoverable and unrecoverable material. Nevertheless, Table 5 B.1 does give an idea of how a nation's secondary resource of a material can grow over the years. A second aspect of the concept of secondary supply is the generation of secondary materials. This includes materials generated as scrap in production as well as the movement of a material out of the stock of existing products via wear, damage, or obsolescence The quantity of materials generated is usually either nearly or completely independent of the technologic capabilities and economic forces which prevail in the secondary recovery market.b The justifications for and the qualifications to this statement are considered later. The final aspect of the concept of secondary supply consists in the secondary recovery process It is at this point that the technologic and economic forces of the secondary recovery market become the controlling fac-

Jan 1, 1976

By Bryon W. Cheever

The greatest objection to be brought against the present methods for estimating phosphorus in iron and steel, is the time consumed in the operation. The following method, originated and perfected by Mr. E. D. Campbell, assistant in the chemical laboratory of the University of Michigan, will, 1 think, if carefully followed out, give results that are sufficiently accurate for technical purposes, and will give them in less time than they can be obtained by any other process. The process consists in comparing the color obtained by the action of stannous chloride upon a solution of the phospho-molybdate precipitate obtained from the solution of iron or steel, with that obtained from a standard solution of molybdie acid which represents a given amount of phosphorus. The operation is as follows : Take of ordinary steel 1 grm. and treat as in any of the wellknown processes until the phosphorus is precipitated as ammoniumphospho-molybdate. When precipitated, the phospho-molybdate precipitate is filtered out, thoroughly washed with an acid solution of ammonium nitrate, and, finally, twice with water, to remove most of the ammonium nitrate. The precipitate is then dissolved in about 1 c. c. of 10 per cent. potassium hydrate, which is let fall drop by drop on the filter till the precipitate is dissolved ; the filter is now washed with about 25 or 30 c. c. of water, and the potassium hydrate solution, which now consists of 25-32 c. c. of solution, is boiled until the peculiar frothy appearance, which first appears on boiling, is entirely gone. The solution is then cooled until perfectly cold, and about 10 or 15 c. c. of strong hydrochloric acid added ; if the solution is kept cold this will form no precipitate, but a light yellow or colorless solution. The solution is now ready for the addition of stannous chloride, and the subsequent comparison of color produced with that obtained from the standard molybdie acid. The comparison is made in tubes that are calibrated like carbon-tubes, but which are larger, about 5/8-inch bore, and graduated to 100 c. c.; this makes them about 18 inches long. To make the comparison of color, first transfer the now acid solu

Jan 1, 1886

By Benjamin F. Merembeck

A mutispectral scanner (MSS) obtains remotely sensed data of the earth's surface in vector form, one vector element for each spectral sensing band of the MSS. Data generated by either airborne or orbiting MSS systems are organized in a lattice of scan lines and elements within scan lines. Each element, called a pixel, is represented by an observational vector and corresponds to a relatively small specific area on the ground. The total observations for a sensed scene frequently are in the millions and are composed of a number of populations, each representing a different land form category. Based on samples from the populations, the mean vectors, or spectral signatures, and the covariance matrices for the categories may be estimated. From these, an among category covariance matrix and a combined within category covariance matrix can be found. The total among category variance is the trace of the among category covariance matrix. Canonical analysis finds a linear transformation matrix such that the first transform variable accounts for the maximum possible part of the total among category variance. Similarly, the second transform variable, orthogonal to the first, accounts for the maximum possible part of the remainder of the total variance, and so on. Such transformation often results in over 95 percent of the total variance accounted for in the first three canonical variables, even though the initial number of spectral bands exceeded twenty. Transformation of bulk data into three canonical variates allows color map products to be developed by assigning each variable to a different basic color. Such color products are believed to be more useful for photo-interpretation than color products resulting from any combinations of three of the initial spectral bands.

Jan 1, 1977

By Harold G. Moulton

IT is highly significant that engineers should seriously consider the interrelations of technology, economics, and government. It is indicative of the emergence of maladjustments and problems that perplex our thinking and frustrate our activities. Instead of a world in which scientific discoveries and their applications through engineering to the processes of wealth production are regarded as the royal road to progress, we now find science and engineering being made responsible, in no small degree, for our economic and social troubles; and the powers of government are even being invoked to stem the tidal wave of technology. Indeed, there is a deep-seated fear, manifested in the writings of some of our greatest scientists as well as in popular discussions, that science may destroy our civilization.

Jan 1, 1938

By A. B. Kinzel

ALTHOUGH calcium carbide and other compounds of calcium, as well as a number of calcium alloys, are well known and are the basis of important industries in the of United States, calcium metal has been thought of as something of a rarity and has received comparatively little attention from industrial metallurgists. The metal may he made in a number of ways, but the electrolytic deposition of calcium from a molten calcium chloride bath was the first process to be used for its commercial production and is still the standard procedure. Calcium metal has elicited little interest among nonferrous metal producers, as the demand has been relatively small and its production restricted to only a few plants, exclusively in France and Germany.

Jan 1, 1941

By Herbert Hoover

THE time has arrived in our national development when we must have- a definite national- program in the development of our great engineering problems. Our rail and water transport, our water supplies for irrigation, our reclamation, the provision of future' fuel resources, the development and distribution of electrical power, all 'cry out for some broad-visioned national guidance. We must create a national engineering sense of provision for the nation as a whole. If we are to develop this national sense of engineering wand its relations to our great human problems, it must receive the advocacy of such institutions as this. We, together with our sister engineering societies, represent the engineers of the United States. It is our duty as citizens to give voice to those critical matters of national policy which our daily contact with this, the fundamentally constructive profession, illuminates to us. Just as our medical associations voice the necessity of -safeguards to national health; as the bar associations of safeguards to our judiciary, so the engineers should exert themselves in our national engineering policies. We have none; but we need some, or the next generation will face a lower instead of a higher standard of living than ours.

Jan 1, 1920

By D. F. Kelsall

The hydraulic cyclone, in simple or modified form, is finding increasing application in metallurgical processing. In this article, the author considers several aspects of conventional applications, less conventional applications and some potential uses of modified cyclones. Information concerning the mechanism of separation within a cyclone and the effect of the major variables is summarized. During the past twenty years, and especially in the last decade, hydraulic cyclones have found increasing application in metallurgical processing as classifiers and, under special circumstances, as thickeners. To a more limited extent cyclones have been used to extend heavy, or dense, medium separation into the finer size ranges, and several attempts have been made to separate dispersions of immiscible liquids with a view to use in the field of liquid-liquid extraction. A large proportion of published work reports incomplete data, applicable only to particular systems. The more useful papers, covering data of relatively wide significance, have been reviewed recently in considerable detail1,2 and no attempt will be made to cover the same material in the present paper. However, before considering several aspects of conventional application, less conventional applications and some potential uses of modified cyclones, it is considered pertinent to summarize information relating to the mechanism of separation within a cyclone and the effect of the major variables. LIQUID FLOW PATTERNS At any point within a simple cyclone the liquid velocity may be resolved into three components, i.e., the tangential or swirling velocity (v), the vertical velocity (w), and the radial velocity (u). The relative values of these components at selected positions within a typical cyclone have been established for water. 3 The extent to which similar flow patterns exist in systems of considerably higher viscosity, or apparent viscosity, operating under conditions of reasonable pressure drop, is not known with precision, but indirect evidence indicates that up to approximately five centipoise there is no marked change. Beneath the bottom of the vortex finder, envelopes of constant tangential velocity are cylinders coaxial with the cyclone, and, at any horizontal level, starting from near the conical wall, this component of velocity increases with decrease in radius (r) according to the relationship vrn = constant (where 0 < n < 1) This holds to regions near the center of the cyclone where v reaches a maximum value at a radius somewhat smaller than that of the inside wall of the vortex finder. At this point, the centrifugal acceleration, v2/r reaches a maximum value. As the radius is further decreased the tangential velocity decreases so that v = r. Above the bottom of the vortex finder there is a tendency for the first relationship to persist to near the outside wall of the vortex finder, until v reaches a maximum and then decreases rapidly as the wall is approached. The two most significant features of the vertical velocity distribution are an approximately conical Table I. List of Symbols v = liquid tangential velocity at any point in the cyclone w = liquid vertical velocity at any point in the cyclone u = liquid radial velocity at any point in the cyclone r = radius from cyclone axis to any point ? = half angle of conical portion of the cyclone ?= fluid viscosity d = particle diameter s = liquid specific gravity p = particle specific gravity d50 = the particle diameter which distributes 5090 to overflow, 50% to underflow e = overflow diameter, in. b = feed diameter, in. G = gpm of feed slurry

Jan 1, 1963

By A. E. Lehman

A RECENT demand for some form of panoramic display of an important railway line, showing its branches, connections, and terri tory controlled by it, revealed to the writer the advantages of&apos; a topographical model or relief map fix this purpose. Hitherto, maps of this nature have been used chiefly for scientific and geographical purposes, and confined to a comparatively narrow field of service. They deserve to become more popular and to have their advantages better understood. Much has been written and accomplished in this direction by Prof. Lesley, Messrs. Harden, Moulten, de Mendonca Cortez, and others; but I believe their pub lished descriptions of the methods employed in the construction of these models are confined to those used by themselves. It is the writer&apos;s aim to present in condensed form these various methods, and some suggestions of practical value as to the most economical course of procedure, as well as to mention some of the uses that may be made of the results obtained Methods of Construction.—Many different materials have been prepared and used in the preparation of relief maps, such as metal, clay, plaster, gypsum, wax, putty, Card-board, papier-mache, wood, and compositions of varions kinds, with results more or less success ful : wood, however, in the writer&apos;s experience, has been found to be by far the most satisfactory, combining the advantages of stability, accuracy and ease of handling. The following is a brief description of several of the methods used in constructing topographical models : When clay, wax, putty, compositions or materials of a plastic nature are used, the operator carries his work up from its base by means of measurements or by the eye, manipulating and shaping the material as best he can, ac cording to such features of his subject as he wishes to delineate. This process requires remarkable skill, and given this, will probably fall short even then of an approximation to accuracy; lacking essential elements of detail nil over the work and exactness, particularly in position and elevation of the most important points in the territory mapped. When either of the above mentioned materials or compositions are used, metal or wooden pins are sometimes driven into the base or level datum plane of wood, the top of these pins giving the eleva-

Jan 1, 1886

Phase II of President Nixon&apos;s economic game plan will incorporate many top flight metals mining companies. The large corporations must receive approval from the Cost of Living Council before increasing prices and or wages. The theory here is that, with large companies complying with advance approval, smaller firms will be examined more closely by government, and thus will be forced also to comply. Rep. Paul McCloskey (R.-Calif.) called for a moratorium on strip mining for "the few years involved before we adopt a national energy policy and a national land use policy." McCloskey, who is a cosponsor of Congressional legislation that would outlaw strip mining, told a hearing that a "moratorium can scarcely hurt us until national energy and land use policies are adopted."

Jan 1, 1971

By Herbert Clark Hoover, Lou Henry Hoover

We give the following brief notes on early works containing some reference to mineralogy, mining, or metallurgy, to indicate the literature available to Agricola and for historical notes bearing upon the subject. References to these works in the footnotes may be most easily consulted through the personal index. GREEK AUTHORS.-Only a very limited Greek literature upon subjects allied to mining or natural science survives. The whole of the material of technical interest could be , reproduced on less than twenty of these pages. Those of most importance are : Aristotle (384-322 B.c.), Theophrastus (371-288 B.c.), Diodorus Siculus (1st Century B.c.), Strabo (64 B.c.-25 A.D.), and Dioscorides (1st Century A.D.). Aristotle, apart from occasional mineralogical or metallurgical references in De Mirabilibus, is mostly of interest as the author of the Peripatetic theory of the elements and the relation of these to the origin of stones and metals. Agricola was, to a considerable measure, a follower of this school, and their views colour much of his writings. We, however, discuss elsewhere1 at what point he departed from them. Especially in De Ortu ct Causis does he quote largely from Aristotle&apos;s Meteorologica. Physica, and De Coelo on these subjects. There is a spurious work on stones attributed to Aristotle of some interest to mineralogists. It was probably the work of some Arab early in the Middle Ages.[ ]

Jan 1, 1950

By F. Z. Schellenberg

(Pittsburg Meeting, March, 1910.) SYSTEMATIC exploitation in the Pittsburg coal-seam on a large scale is simple where the boundaries of the property do not interfere by forcing drainage-, ventilation-, and transport-lines of entries to be run to particular confined fronts. A prime condition governing development is the natural direction of the seam&apos;s perpendicular cleavage-planes, giving long lines of smooth faces near together and parallel, bearing about 65° to the left of the meridian and therefore crossing the basins. The gradients of dip into the basins change from 10 per cent at the east rim to practical flatness northwestward across the great coal-fields, a hundred miles wide; the clip being halved in rate at each successive crossing-over of an anticlinal crest. Elevations above sea-level on this transverse section, in scope of present development, differ by 1,000 ft. between low trough and high outcrop. Local irregularities of dip are found, but the main feature to be recognized is the pitch of the basins-the general rise northeastward at 20 ft. per mile, from 100 ft, below sea-level at the low point near the. SW. corner of Pennsylvania to 1,500 ft. and more above tide, and the appearance then, at the surface, of the lower coal-seams carried in the next deeper-lying thousand feet of rock-measures; below which series come the oil- and gas-sands of Oliphant&apos;s charted column of strata, reaching down altogether 3,000 ft. below the Pittsburg coal-seam. Because of -the general regularity of occurrence of the coal-seam, the mine-map depicting the courses of economic operation to be undertaken and the steps in controlled exhaustion, need be but a projection of two dimensions on the horizontal plane of space, and this for the most part composed of natural, almost unbroken lines, on the face and on the end of the coal, co-ordinating rectangularly.

Jul 1, 1910

By J. B. Newsom

SAFER, cheaper, and faster sinking of mine openings seems to have been realized with the completion of a borehole 5 ½ ft. in diameter and 1208 ft. deep, in Minnesota, during 1938. Moreover, as the opening is to be used solely for ventilation, its circular cross section, smooth walls and freedom from fire hazard recommend it in comparison with the usual timbered shafts of rectilinear cross section. It should be pointed out that a drill hole sunk without the use of explosives frequently will stand open without support, whereas a shaft sunk by standard procedure using dynamite usually must be timbered because of the wall-shattering effect of explosives. The saving in maintenance resulting from the elimination of timber is obvious. The work was done by Pickands Mather & Co. at its Zenith mine, Ely, Minn. This company wanted a ventilation opening capable of delivering 50,000 cu. ft. of air per minute to the fourteenth level, 1200 ft. below the surface. While several general articles1-3 have described the method used, detailed time and performance records have not been presented before. Moreover, with a method as new as this, it is important to compare the results attained under widely varying conditions. Among the new conditions faced at Ely were some extremely hard rock, a series of vertical fractures, seepage water, and some long stretches of sound rock which, combined with excellent equipment, gave a chance to operate without unusual delays. Developments in boring large holes have generally taken the obvious course of increasing the size of the equipment, a line of attack that has resulted in putting down 3-ft. diameter holes at damsites for studying the foundations4 and in drilling ventilation openings between levels at Butte. 5 Such drills operate from the collar of the hole, and the power from the drill is transmitted to the cutting tool through drill rods or pipes. In order to keep down the volume of rock that must be ground to sludge, the cores in large-diameter drilling are made as large in diameter as possible. Their large diameter increases their weight per foot of length, which

Jan 1, 1939

By F. R. Zachar

IT has always been understood, in northern West Virginia where both the Pittsburgh and Sewickley seams are mined, that pillaring or splitting in the lower Pittsburgh seam could break the interval strata and make mining in the overlying Sewickley difficult or impossible. In some instances, however, mining methods practiced in the overlying Sewickley have reversed the problem, resulting in a shifting of the intermediate layer and destroying valuable acreages of the Pittsburgh seam below. The Pittsburgh seam in this area is, on the average, 102 in. thick. About 18 in. of low-quality head coal are left for roof protection as it is mined. Immediately over the coal are two draw slates, two rider &apos;seams, and a good hard black shale, locally called black rock, which serves as a permanent roof where draw slates and riders are taken down on certain main haulroads. In most areas mined in this seam in the past the bottom has been satisfactory but soft. However, in areas now being mined by the Christopher Coal Co. in Monongalia County the bottom is very hard and unyielding. The Sewickley seam, lying 85 ft above the Pittsburgh, will average nearly 70 in. in thickness and is overlain by massive shales and sandstones. Much of the seam is mined only down to the "sheep skin," a hard band about 4 in. above the bottom, which is composed of relatively hard shale. Fig. 1 shows a typical cross-section through the Pittsburgh and Sewickley seams in the area being discussed. The thin Redstone seam is not deep-mined but is stripped in some locations where it outcrops. Most of the Sewickley seam in the Morgantown areas has been mined out from 10 to 30 years. There are at present only two large mines and five or six others of small production operating in that seam. Mining systems in the past were generally of the room and pillar type with some full pillar extraction. This seam in the Scott&apos;s Run area was operated by as many as thirty or forty different companies at one time, during an era beset with strikes, market failures, and depressions. Most of the barrier pillars along the many main haulroads were abandoned, and blocks of Sewickley coal that would be fully recovered with today&apos;s machinery were left unmined when conditions became anything less than favorable. Consequently the mined-out Sewickley is spotted throughout with solid blocks varying in size from 100x100 ft to 200x400 ft and larger. It is these unmined Sewickley blocks surrounded by worked-out portions that have caused transmissions of roof stresses to underlying Pittsburgh mining areas, see Fig. 2, resulting in untold difficulty. As the Christopher Coal Co. operates both the Pittsburgh and Sewickley seams, accurate maps of workings in both seams are readily available and are regularly consulted. The first Pittsburgh squeeze attributed to overlying Sewickley blocks occurred in the Arkwright mine, where a shuttle car crew was developing a section consisting of seven panel headings. These entries were being driven in solid coal 3400 ft from the nearest worked-out Pittsburgh area. As mining advanced it was noticed that certain ribs began to slough and certain areas to show signs

Jan 1, 1952

By W. S. Landis

IN brief, this is the story of an attempt to Americanize a process originally developed in Europe. The story will be recited in two sections, the first dealing with the process as developed by the European engineers; the second containing the improvements and modifications of American origin, together with some details of the operating results of the unit as finally assembled. Developments in other directions in this same field have not, up to the present, pointed out an economic future for the process, therefore our record here is largely a report of development progress. Whether some particularly favorable location will be found at some future time for a commercial installation cannot as yet be fore-told. The project is now at a standstill. The peculiar tools of the electrometallurgist should be of great interest to the zinc smelter. The low thermal efficiency of the zinc retort, its comparatively small-scale unit and its intermittent cycle as it stood in 1925, should make this art a particularly fertile field for the electric fur-nace. Yet in spite of years of work recorded in volumes of literature, and an expenditure of large sums of money, there is not a single electrothermic zinc smelter operating anywhere in the world. In this industry the electric furnace plays only a secondary part today.

Jan 1, 1936

By E. Lancaster-Jones

THE gravity magnitudes obtained by means of observations with the Eötvös balance in the field are necessarily resultant or total effects due to all abnormalities of mass distribution, including even the effects due to the ellipticity and rotational motion of the whole earth. Since the object of the survey is to isolate the effects which arise solely from some particular subterranean feature, and to deduce therefrom the configuration and extent of this feature, the first step is to eliminate from the observed effects all those due to "disturbing" (i. e., unwanted) features, whether above or below the surface of the ground. The disturbing features have different characteristics, according to their situation relative to the center of the balance and to the horizontal plane through the foot of the balance, or station point; this diversity was recognized by Eötvös, who divided the total effects into so-called Normal, Terrain, Topographical, Cartographical and Subterranean effects. This classification has been adhered to by most subsequent investigators, but the writer prefers to employ the term "three-dimensional," which really indicates the essential character of the class of effect known as "Subterranean," at any rate from the standpoint of the computer of effects. Before disturbing effects can be eliminated, the features must be measured up or surveyed, whether by topographical, mining, or boring methods, and then the effects of each feature calculated and subtracted from-the total observed effects. After this the problem of interpreting the residual effects will itself necessitate the computation of the assumed feature, or even a series of trial features.

Jan 1, 1928

By Eugene F. Poncelet

GLASS squares compressed on edge by steel jaws in poor contact with them developed jagged "partial-contact" cracks caused by the formation of local tensile stresses. Compressed by steel jaws in perfect contact, they developed smooth "release cracks" during release of the pressure, caused by the formation of local tensile stresses during the release of the pressure. All these cracks were parallel to the pressure. A Microflash photograph of a disintegrating specimen under sufficient pressure reveals a network of fractures roughly normal to each other, also "release cracks" and a disintegration cloud. The Griffith theory is amended to account for the formation of a first crack. A new theory, based on the theory of thermal agitation and wave propagation, is proposed to account for the progress, velocity and forking of cracks. The network of fractures is shown to have been caused by reflection at a free boundary of pressure pulses emanating from a first crack. Postulating equal distribution of energy in the pulses emitted on either side by a crack in particles, the smaller fragments are shown to continue fracturing preferentially while some of the coarser fragments remain as residual pieces. As comminution of the smaller fragments proceeds, the solid is reduced to a collection of residual particles of smaller and smaller sizes, accounting for the disintegration cloud. EXPERIMENTAL PROCEDURE Apparatus A crushing device was built, consisting of a steel frame and two polished, hardened steel jaws to crush plate-glass samples. This device was placed between the plates of a hydraulic press (Fig. 1). For centering the pressure, the upper jaw was guided vertically and provided with a rounded top. Later it was replaced by a steel jaw ground out of a 2 1/2-in. steel ball, the lower surface being ground to an optical flat (Fig. 2). Four rollers were used to eliminate side thrust. Screws and centering blocks served to center the specimen in the crushing device. Hard steel shims placed under the shoulder of the upper jaw limited the "follow through" of the jaw after failure of the specimen. Stress distribution was first examined with a polariscope mounted on an optical bench, using monochromatic light. It was found convenient to mount polaroid, quarter wave and monochromatic plates directly on the device itself. A Microflash unit* was used as light source for the photographs. A gold-paint pattern was fused on the plate-glass specimens and connected into the spark-

Jan 1, 1944

By William E. Ford, Edward Salisbury Dana

The Silicates are m part strictly anhydrous, in part hydrous, as the zeolites and the amorphous clays, etc. Furthermore, a large number of the silicates yield more or less water upon ignition, and in many cases it is known that they are, therefore, to be regarded as basic (or acid) silicates. The line, however, between the strictly anhydrous and hydrous silicates cannot be sharply drawn, since with many species which yield water upon ignition the part played by the elements forming the water is as yet uncertain. Furthermore, in the cases of several groups, the strict arrangement must be deviated from, since the relation of the species is best exhibited by introducing the related hydrous species immediately after the others. This chapter closes with a section including the Titanates, Silico-titanates, Titano-niobates, etc., which connect the Silicates with the Niobates and Tantalates. Some Titanates have already been included among the Oxides.

Jan 1, 1922