Search Documents

By AIME AIME

IT IS impossible in this short sketch to give a detailed description of each part of the plant at Bethlehem, therefore, only such facts will be touched on as are necessary to give a general idea of the works. The extent of the plant, and the fact that the units making up the various departments are located in different parts of the works, make it impracticable to mention the departments in any regular order with regard to their location. They are, therefore, mentioned approximately in the order of their relation to each other with reference to their functions in the making of the various products.

Jan 1, 1924

By O. C. Wheeler

In order that the series of reports on oil and gas in Colombia may be complete, the report for the year 1941, which was not available for Volume 160 of the TRANSACTIONS, is given here. The report for 1945 begins on page 4o6.

Jan 1, 1946

By A. W. Hesse

The trend of American construction toward permanence and longevity is noticeable in the more recent coal plant installations; also, the policy of many coal operators has changed from seeking to obtain the desired tonnage from several plants of small capacities to designing a single installation to produce the whole amount. The mine openings and plant of the Nemacolin mine of The Buckeye Coal Co., are located on the Greene County side of the Monongahela River, 73 miles south of Pittsburgh. The map (Fig. 1) shows the general location, also the Lambert syncline. This syncline partly accounts for the selection of the site; the other reasons were the possibilities of rail and river shipments. Two shafts and a slope were sunk to the coal, work starting on all three in the second half of the year 1917. The air shaft was sunk to a depth of 243 ft. and completed in February, 1918; the slope was completed in November, and the skip shaft was stopped at a depth of 21 ft. below the coal, then the concrete lining was stopped 8 ft. above the coal August, 1918. Work on the skip shaft was resumed May, 1923, and sunk to a depth of 60 ft. below the coal by September, but it was not until May, 1924, that the lining was poured. Max. Min. WateR Water during after Sinking, Crouting, Depth or Cu. Yd. Cu. YD. Gal. per GaL. per Opening Size Length Excav. Conc. Min. Min. Air shaft..... 20 ft. diam. 251 ft. 8 in. 4788 1902 475 2 Slope........ 11 it. by 19 it. 1 in. 857 ft. 11500 5200 50 2 Skip shaft.... 32 ft. 8 in. by 12 it. 8 in. 296 ft. 6042 2293 300 3 Fig. 2 shows sections of these openings. The surface plan shows the relative positions of the openings. Coal was first hoisted from the air shaft May 7, 1918, and entry driving was continued; but the coal had to be stored, as the railroad had not been extended from Crucible to Nemacolin. As soon as the slope was driven to the coal and the linings concreted, the entries were driven along projected lines to connect with those advancing from the air shaft, and skip shaft. As soon as the underground connections had been made between the two shafts, the hoisting by buckets was inaugurated at the skip shaft and construction on the fan at the air shaft started.

Jan 1, 1927

By R. D. Nelson, S. D. Dahlgren

The conditions of temperature, strain rate, and total strain favoring deformation by grain boundary sliding, slip, or deformation with concurrent recrystallization were evaluated for alpha plutonium. Grain boundary sliding and slip were studied by examining structures formed on polished surfaces with 4.5 pct compressive deformation. The conditions required for recrystallization were determined from compressive deformation us time curves. At 110" C and at a strain rate of 10&apos;per min, deformation was almost exclusively by grain boundary sliding whereas slip was the predominant deformation mode at -10°C and lo-&apos; per min. Defarmation at intermediate tenzperatures and strain rates produced structures showing mixtures of grain boundary sliding and slip. Recrystallization occurred concurrently with deformation only after a critical strain was reached. About 14, 6, and 3 pct strain was required at 105", llO°, and lZO°C, respectively, before recrystallization started, irrespective of the strain rate in the range of lo-&apos;1 to 10&apos;4 per nzin. L HE temperature and strain-rate dependency of the modes of plastic deformation were evaluated for high-purity as-cast alpha plutonium. The techniques used to study slip and grain boundary sliding were similar to those employed previously for alpha plutonium by Bronisz and Gorum,&apos; and spriet.&apos; Recrystallization was investigated using the methods reported by Nelson.3 Bronisz and Gorum&apos; found that slip occurred on more than one slip system at room temperature, and suggested that grain boundary sliding also contributed to the deformation. spriet2 found that deformation was predominantly by slip at room temperature, and observed one to three orientations of slip traces in individual grains. In addition, he deformed polished samples at 10O° C, but concluded that the deformation character of alpha plutonium at 100° C and at room temperature were not essentially different. Several investigators reported that twinning was only occasionally observed.1&apos;2&apos;4 Nelson3 recently found in creep tests that high-purity alpha plutonium would recrystallize concurrently with compressive deformation at temperatures between 25" and 115°C. EXPERIMENTAL PROCEDURE Electrorefined plutonium having less than 300 ppm total impurities was received from Los Alamos Scientific Laboratory in the form of +-in. diarn cast rods. Major impurities were americium, <I00 ppm, and tungsten, (60 ppm. Less than 25 ppm each of other impurities were present. The rods were cut into right half-cylinders 0.35 in. long and 0.25 in. in diam, and the flat faces along the cylinder axes were metal-lographically polished. To avoid loss of the metallo-graphic polish by oxidation, the polished samples were deformed in a silicone fluid heat treating medium contained in a chamber evacuated to a pressure of lo-&apos; torr. Deadweight loading was used to compress the samples between 4.5 and 20 pct at strain rates between 10"4 and lo- &apos; min-&apos;. Strain rates were determined by dividing the total deformation by the elapsed time of the test, even though the strain rate was not constant during deformation. Curves of strain vs time for samples deformed with a constant compressive stress3 show that the strain rate changes by less than a factor of four during the testing of a given sample, which is small compared to the three orders of magnitude change in strain rate investigated. Two samples were loaded into an ordinary metallographic mounting mold and impacted by striking the mold piston with one blow of a 2-lb hammer. Deformation temperatures for the two impact samples were 25" and 90°C. The samples, following deformation, were washed in carbon tetrachloride and their polished and deformed surfaces were immediately inspected metallographi-cally. Subsequently, the deformation structures were replicated with acetate replicating tape for later electron microscope examination, and the samples were then repolished and etched to reveal the microstruc-tures of the deformed metal. Second-stage carbon replicas were prepared from decontaminated acetate replicas using the procedure developed by Miller, Bierlein, and astel.&apos; Additional samples, which were 0.35 in. long by 0.25 in. in diam, were used to obtain constant load deformation vs time curves. These samples were deformed 10 to 20 pct with loads of 15 and 20,000 psi at 120°C; 30, 45, and 55,000 psi at 110°C; and 20 and 30,000 psi at 105°C. Samples were polished and etched to determine whether or not recrystallization or twinning had occurred during deformation. RESULTS AND DISCUSSION The experiments showed that alpha plutonium deforms by grain boundary sliding, slip, and deformation with concurrent recrystallization. Deformation by twinning was insignificant. Metallographic examination of polished and deformed surfaces revealed grain boundary sliding and slip. The start of recrystallization was ascertained from constant load deformation vs time curves. Deformed surface structures of samples compressed 4.5 pct under four different conditions of temperature and strain rate, Fig. 1, show how the deformation mode changes from predominantly grain boundary sliding to predominantly slip with increasing strain rate and decreasing temperature. Deformation at 110°C and 10" 4 min-&apos;, Fig. l(a), was predominantly by grain boundary sliding. Only a few slip traces can be seen in Fig. l(a).

Jan 1, 1969

By AIME AIME

BY COMBINING the sessions on reduction and refining of copper, lead and zinc it was possible to devote an entire day to nonferrous metallurgy. Four interesting papers were presented at the morning session and four more in the afternoon. In the discussion of papers on copper, F. R. Pyne acted as chairman, with H. M. Shepard as vice-chairman, whereas for those on lead and zinc, F. F. Colcord acted as chairman, with C. R. Hayward as vice-chairman. The paper by P. D. I. Honeyman on the smelting of raw concentrates in the reverberatory furnace was presented by Mr. Pyne and discussed by Messrs. Mazany and Hayward. The interesting paper by E. S. Bardwell, com- paring the use of various fuels in copper-refining furnaces at Great Fails, Mont., was presented by Mr. Shepard and discussed by Messrs. Boggs, Gronningsater and Hayward. That by R. G. Knickerhocker, describing the stationary basic copper converter at Messina, Transvaal, was presented by Mr. Pyne, together with a written discussion by c. R. Kuzell, of the United Verde Copper co. It was an interesting illustration of how well-known processes may sometimes be modified to fit into unusual conditions.

Jan 1, 1932

By Andrew Fletcher

AS good health is the most important asset in life, the development of healthful conditions should be the one common meeting ground of agreement between management and labor. Health should not be a subject to be pulled apart, shoved around, or bargained about. Differences of opinion may exist in the procedure and techniques employed in approaching the goal of maintaining the health of workmen, and in the method of increasing the ultimate profit of the employer by improved working and living conditions. Such matters are doubtless appropriate subjects for discussions between the interested parties, but techniques are only tools. If an employer fails to remedy a hazard or a menace which contributes to poor working condlions, this constitutes a legitimate grievance. It should not be necessary, however, nor is it desirable that fundamentals of health maintenance become matters of collective bargaining, any more than should the principles of management and engineering. I have been especially concerned during the last few months with the propaganda in collective bargaining negotiations throughout the country for including in union contracts a given number of days of sick leave with pay. We all

Jan 1, 1946

By A. B. Cook

Gas cycling is generally considered a much less efficient oil recovery mechanism than water flooding. HOWever, recoveries from some fields have been exceptionally high as a result of gas cycling. Recovery from the Pick-ton field, for example, was calculated to be 73.5 perceni of the stock-tank oil originally in place. In evaluating pressure maintenance projects, determining how much of the recovery is due to displacement by gas and determining how much is due to vaporization of the imrnohile oil in the flow path of the cycled gas is very difficrilt. Even though most of the oil is recovered by displacetr~ent, the success of a project may depend on the amount of oil vaporized. A limited number of experiments have heen performed with a rotating model oil reservoir that simulates gas cycling operations and allows a separation of the oil from, tile free gas flowing into the laboratory wellbore at reservoir conditions, thus revealing which is displaced oil and which is vaporized oil. It Iras been determined that the amount of varporizatio&apos;n is .significant if proper conditions exist These experiments show that oil vaporization depends on pressure, temperature, volatility of the oil and amount of gas cycled. Increases in each of these conditions increase the volume of oil vaporized. Data from six experiments affecting vaporization are presented to illustrate reservoir condition that range from favorable to unfavorable. 111 these eaperitnenis recovery by vaporization ranged from 73.6 to 15.3 percent of /he immobile oil (oil not produced by gas displacerrlt). INTRODUCTION Between 1930 and 1950, gas cycling was a popular. oil recovery practice. especially for the deeper reservoirs. Later, with many case history-type studies published for both gas cycling and waterflooding, it was generally believed that waterflooding was far superior to gas cycling, even when gas cycling was conducted as a primary production procedure by complete pressure maintenance. A good example illustrating the advantage of water-flooding over gas cycling is given in a paper by Matthews&apos; on the South Burbank unit where gas injection was followed by waterflooding. The author concluded in part that "Early application of water injection, without the intervening period of gas injection, would have recovered as much total oil as ultimately will be recovered by waterflooding following the gas injection, and total operating life would have been shortened". This appears to be a logical conclusion. However, it should not be applied to all fields. Pressure maintenance with gas in the Pickton field, as reported by McGraw and Lohec;&apos; will result in a much larger percentage of oil recovery than was obtained in the South Burbank unit. The great success in the Pickton field resulted partly from vaporization of the immobile oil in the flow path of the cycled gas. The amount of vaporization is related to the following conditions: volatility of the oil as reflected by the APT gravity of the stock-tank oil; reservoir temperature; reservoir pressure during gas cycling; and the amount of gas cycled. Therefore, the U. S. Bureau of Mines is investigating these effects on vaporization in a research project using a model oil reservoir. Three different stock-tank oils having 22, 35 and 45" API gravities are being used as base stock to synthesize reservoir oils. Experiments are being performcd to determine vaporization at 100, 175 and 250F and at 1,100, 2,600 and 4,100 psia. This is a progress report showing the results from six experiments. Other Bureau of Mines reports"- concerning vaporization are listed. LABORATORY EQUIPMENT AND PROCEDURES The equipment &apos; consists of an internally chromium-plated steel tube packed with finely sifted Wilcox sand. The tube is approximately 44 in. long and has an ID of 13/4 in. The sand section contains approximately 570 ml of voids, has a porosity of 32 percent, and a permeability to air of 4.3 darcies. A unique feature of the laboratory reservoir (Fig. 1) permits the tube part to rotate at 1 rpm while the outlet and inlet heads are held stationary. The outlet end contains diametrically opposed windows to permit observatlon of the flowing fluids, and two valves, one on the top and the other at the bottom. Oil and free gas. when being produced simultaneously, can be separated by manipulating the two valves to keep a gas-oil interface in view through the windows. Thus, only gas is produced through the top valve and only oil flows through the bottom valve. The laboratory equipment was designed to study vaporization. Therefore, a uniform reservoir was made using dry sifted sand as opposcd to using a consolidated sand core with interstitial water. Furthermore. the reservoir was tilted to minimize fingering of gas. This tilting also in-

By John Chipman, Theodore B. Winkler

IN order to understand more fully the complexities of the reactions occurring between the liquid steel and the slag in the basic open-hearth steelmaking furnace, investigations in this country and abroad have turned to laboratory equilibrium studies. This paper is one of a series of reports on investigations being conducted at the Massachusetts Institute of Technology. The experimental work was completed early in 1942. The slag systems found in the basic open hearth are very complex, being made up of at least eight major components and as many others whose effect might be classified as minor. The first two papers of the series, by Fetters and Chipman,l,2 as well as the paper by Taylor and Chipman,3 dealt with the simplest possible slag system that would resemble those found in the basic open hearth-the slag system consisting of CaO-MgO-SiO2-FeO. (Taylor&apos;s rotating induction furnace eliminated the necessity of contamination of the slag by MgO.) Having arrived at some reasonable conclusions regarding the physical chemistry of the reactions between molten iron and the simple slags at equilibrium, the next step was to investigate more complex slag systems. The major purpose of the present investigation was to determine what factors control the distribution of phosphorus between molten iron and the more complex basic slags at equilibrium, and to what extent these factors are influential. The slags used contained CaO, MgO, Si02, FeO, Fe203, P205, MnO, A1203 and CaF2, but not all of the slag samples contained all of these components at one time. REVIEW OF LITERATURE Although a number of interesting papers have been published on the subject of dephosphorization of an iron bath, there are as yet no results from laboratory studies that give thoroughly reliable information on the dephosphorization reaction. Even for the supposedly simple Fe-O-P system involving iron-phosphorus melts and iron oxide-iron phosphate slags, the experimental results are contradictory and no formulas have been established that adequately fit the equilibrium conditions. The Fe-O-P system has been studied by Schackmann and Brings4&apos; von Samson-Himmelstjerna,5 Oelsen and Maetz,6 Bischof and Maurer,7 Diepschlag and Schürmann,8 and Herty,9 and the results of their investigations appear in Table I. A number of different equilibrium constants and distribution ratios

Jan 1, 1946

By F. S. Crawford

IRON and copper are mined in the Lake Superior district. The iron mines of the district have the best safety record for that industry in the country as a whole, while the copper mines of the district rank second in two of the four years recorded (Table 1). In Utah copper comes mainly from open-pit mines, which enables that state to lead easily in safety. All of the Michigan production comes from deep underground workings. About 60 per cent of the iron miners in St. Louis County, Minnesota, are employed at open-pit mines; this favorably affects the combined open-pit and underground accident-frequency rate, as this county provides most of the Minnesota-mined iron ore. In Michigan, however, there are few open-pit mines, the bulk of the production coming from underground mines, while all of the Wisconsin production, just across the state line from Michigan, is from underground mines. In spite of the fact that fewer mines in Michigan use the safer open-pit method, the iron-mining industry of that state maintained a consistently low record from 1931 to 1934; however, it was many points behind its nearest competitor, Minnesota, with its much greater production from open-pit mines.

Jan 1, 1939

F A. THOMSON, president of the Montana School of Mines, gave an interesting talk on mining schools of the past, present and his ideas of the future before a recent meeting of the Montana Section of the A. I. M. E. He covered the history .of the various mining schools and com- pared the three main types of schools; those attached to or forming part of an endowed college or university such, for example, as&apos; the Columbia School of Mines, the Mining Department of the Massachusetts Institute of Technology and the Mining Department of Stanford University. These resemble in a general way the second class, those attached to the state universities and colleges. The schools of this general type have had varied success.

Jan 1, 1928

By George Burrell

INTRODUCTION THE senior author of this paper, while in Colorado on other official business, made a trip to the Cripple Creek gold-mining district to get more data than are at present available regarding the composition of the gas that issues from the rock into the mines of the district. This was done at the suggestion of George S. Rice, Chief Mining Engineer of the Bureau of Mines. There are many questions of interest and importance in connection with the ventilation of the mines in the Cripple Creek district, such as the menace to life and mining of a suffocating gas entering the mines from the rock, the danger due to powder smoke (from blasting operations), and danger of continued inhalation of rock dust by the miners. This report confines itself to the first problem, the gas from the rock, and principally to one phase of this question, the composition of the gas and its effects on men and lights. A more thorough study of this and other ventilation problems is planned. That the, rock gas is a real menace is shown by the fact that miners (variously estimated from 25 to 50 by different persons interviewed) have been killed by it in the 25 years that mining has been vigorously carried on at Cripple Creek. Many men have had narrow escapes from death, some of them having been incapacitated for days. In addition, much loss of time results because at certain periods of the year or on certain days it is impossible to enter some workings. At a few mines fans force air into the workings, thus supplementing the natural ventila-

Jan 5, 1916

By R. F. Mehl, C. S. Barrett, A. G. Guy

INTRODUCTION IN the last few years this laboratory has published a series of papers on the mecha¬nism of age -hardening.14,1,6,11,20 Briefly stated it has been proposed that hardening is caused by lattice strains created by lat¬tice coherency between matrix and precipi¬tate; much experimental evidence has been advanced to support this thesis. The system Cu-Be is an attractive one to study. It is a system that exhibits marked age hardening; it ought to be subject to the type of analysis of structural changes hitherto explored and it is a prominent example of "discontinuous precipitation," which, though studied in other cases, 6,20 remains largely unexplained. This research shows that hardening in the Cu-Be system proceeds essentially as proposed earlier.14 Guinier-Preston zones have been observed to form on the {100) planes of the matrix; no transition lattice was found. Aging and overaging were ob¬served to occur most rapidly in the region of discontinuous precipitation-the grain boundary-apparently accelerated there by strain. The Constitution of the Cu-Be System The Cu-Be constitution diagram is shown in Fig I. The structure of the ? phase was determined by Misch16 as of the caesium-chloride type with a lattice con¬stant of 2.598 Å High temperature X ray photograms of 7.2 pct Be alloy made by Kossolapow and Trapesnikow13 led them to conclude that the structure of the P phase is simply disordered body-centered cubic with [ao] = 2.79 Å at 750°C. Previous Work The initial work on the age-hardening of Cu-Be alloys was that of Masing, Dahl, Holm, and Haase. Their numerous papers were published in book form in 1929, sub¬sequently translated.18 The effects of Be content, solution temperature, aging tem¬perature, and cold work on the hardness developed in these alloys were studied. An initial decrease in the electrical conduc¬tivity was observed when strips of a 2.5 pct Be alloy were aged at temperatures from 200 to 350°C; a wire of the same analysis failed to exhibit this decrease when aged at 350°C. A volume decrease of 0.6 pct oc¬curred during aging at 250°C. Microscopic investigations of quenched and aged alloys disclosed a regularly ori¬ented "striping" (ripples) on the a and on the ß grains. In the case of the ß the cause of the striping was held to be decomposition

Jan 1, 1948

By R. Ehrlich, F. E. Crane

A consolidated porous medium is mathematically modeled by networks of irregularly shaped, interconnected pore channels. Mechanisms are described that form residual saturations during immiscible displacement both by entire pore channels being bypassed and by fluids being isolated by the movement of an interface within individual pore channels. This latter mechanism is shown to depend strongly on pore channel irregularity. Together, these mechanisms provide an explanation for the drainage-imbibition-hysteresis effect. The calculation of steady-state relative permeabilities, based on a pore-size distribution obtained from a Berea sandstone, is described. These relative permeability curves agree qualitatively with curves that are generally accepted to be typical for highly consolidated materials. In situations where interfacial effects predominate over viscous and gravitational effects, the following conclusions are reached. 1. Relative permeability at a given saturation is everywhere independent of flow rate. 2. Relative permeability is independent of viscosity ratio everywhere except at very low values of wetting-phase relative permeability. 3. Irreducible wetting-phase saturation following steady-state drainage decreases with increasing ratio of nonwetting- to wetting-phase viscosity. 4. lrreducible wetting-phase saturation following unsteady-state drainage is lower than fir steady-state drainage. 5. Irreducible nonwetting-phase saturation 101lowing imbibition is independent of viscosity ratio, whether or not the imbibition is carried out under steady- or unsteady-state conditions. Experiments qualithtiveIy verify the conclusions regarding unsteady-state residual wetting-phase saturation. Implications of these conclusions are discussed. INTRODUCTION Natural and artificial porous materials are generally composed of matrix substance brought together in a more or less random manner. This leads to the creation of a network of interconnected pore spaces of highly irregular shape. Since the geometry of such a network is impossible to describe, we can never obtain a complete description of its flow behavior. We can, however, abstract those properties of the porous medium pertinent to the type of flow under consideration, and thus obtain an adequate description of that flow. Thus, the Kozeny-Carmen equation, by considering a porous medium as a bundle of noninterconnecting capillary tubes, provides an adequate description of single-phase flow. With the addition of a saturation-dependent tortuosity parameter in two-phase flow to account for flow path elongation, the Kozeny-Carmen equation has been used to predict relative permeabilities for the displacement of a wetting liquid by a gas. 1-5 It has long been recognized that relative permeability depends not only on saturation but also on saturation history as we11.6,7 Naar and Henderson8 described a mathematical model in which differences between drainage and imbibition behavior are explained in terms of a bypassing mechanism by which oil is trapped during imbibition. Fatt9 proposed a model for a porous medium that consisted of regular networks of cylindrical tubes of randomly distributed radii. From this he calculated the drainage relative permeability curves. Moore and slobod,10 Rose and Witherspoon,11 and Rose and Cleary12 each considered flow in a pore doublet (a parallel arrangement of a small and large diameter cylindrical capillary tube). They concluded that, because of the different rates of flow in each tube, trapping would occur in one of the tubes; the extent of which would depend upon viscosity ratio and capillary pressure. They limited

Jan 1, 1970

By W. S. CAYPLESS, H. O. Hofman, E. E. HARRINGTON

I. INTRODUCTION. LIME-ROASTING is a term proposed by Ingalls 1 for the operation of forcing air under pressure through a mixture of galena and lime at the kindling-temperature with the object of oxidizing lead and sulphur and of fritting or fusing the charge. If, finely-divided galena were treated in this manner without the addition of lime, the heat set free by the oxidation of part of the lead and the sulphur would be sufficiently great to fuse undecomposed sulphide, and thus stop desulphurization. Besides the chemical action that the addition of lime, limestone or gypsum to the charge may have, the admixture has the physical effect that it keeps the particles of galena separated from one another and accessible to the oxidizing effect of the air. At present, three methods of lime-roasting are carried out on a working-scale, the Huntington-Heberlein, the Carmichael-Bradford and the Savelsberg2 processes. In the last, which interests us here, an 8-ton charge is made up of galena, limestone and perhaps some siliceous or ferruginous flux; the whole is crushed to pass a screen with 3-mm. holes and moistened with 5 per cent of water. It is fed gradually into a bowl-shaped converter, 6.56 ft. in diameter, supported by trunnions attached to a truck. On the .bottom the converter has a grate with blast-inlet beneath. In starting, the truck with the converter

Jan 1, 1907

By Paul F. Kerr

The insufficiencies of our mineral resources are becoming well known, and the national political conscience seems to be troubled at last by our dependence upon mineral commodities which must come from other lands. This realization places increased responsibility upon the industrial, educational, and governmental groups whose task it will be to solve the problems of mineral supply. As we all know, from the time that man first sought mineral deposits until recent years, prospectors have been largely responsible for mineral discoveries. Today the era of the prospector is almost over. The human ants that have literally examined all accessible outcrops and have tested the gravels of nearly all stream beds in the United States have left undiscovered few worthwhile mineral deposits within the scope of their recognition. The pages in the history of mineral exploration are now being turned from the era of the surface prospect to the era of the hidden de- posit.

Jan 1, 1949

By Milton F. Goodrich

The idea of using water-only cyclones to scalp clean coal from the feed to other devices has recently been gaining in popularity.l,2,6 An indication of this popularity is that water- only cyclone scalping is already employed in a few commercial plants. Water-only cyclones scalp the feed to a heavy media vessel in the Warwick plant,3 to Deister tables in the Rowland plant,4 and to a heavy media cyclone circuit in the Amherst Coal Company&apos;s McGregor plant.5 Despite this trend, we found surprisingly little information in the literature on the performance of water-only cyclone scalping. Therefore, we undertook a study of its technical merits, limiting our investigation to a water-only cyclone scalper in conjunction with heavy-media cyclones. We felt this to be a reasonable combination of equipment, since both processes operate well on the same size coal. First, we developed simple mathematical relationships revealing general characteristics of the system. Next, we compared the clean coal yield and quality obtainable by the system on four different coals with that obtainable by heavy-media cyclone circuit alone and water-only cyclones middlings recirculation circuit alone. This was done by using computer program to simulate the operation of the three systems. Finally, we considered the effect that implementation of the system would have on a typical preparation plant circuit.

Jan 10, 1978

By H. E. Stauss, J. Hino

INTEREST in silicon has arisen again in the past decade as a result of improvements in crystal rectifiers.&apos; Although the preparation of silicon was first reported by Berzelius in 1880, the early product was of relatively low purity, and only the need for rectifiers in World War II led to the production of a 99.9+ pct pure powder. This material in crystalline form was consolidated into massive silicon for use, and the method developed was to melt it with selected added constituents as "doping" agents. Melting techniques, therefore, are of great importance. There are two basic problems in producing silicon ingots free of doping additions; one is the prevention of spitting and the other is prevention of cracking of the ingot during freezing. The most satisfactory arrangement yet developed for producing massive silicon is to melt and freeze in a cylindrical quartz crucible surrounded by a concentric heating element and concentric radiation shields or insulation. For example, use can be made of a tubular heater with a high frequency generator as the source of power and reflecting shields of alundum cylinders. The spitting of silicon is related to gas evolution, and the gas comes from two primary causes—adsorbed gas and the reaction products of silicon and the crucible. Gas is also released from bubbles contained in the quartz crucible walls. Improved removal of adsorbed gas can be achieved by means of controlled melting and freezing. The seriousness of the problem in vacuo is reduced with an electrically operated mechanical movement of the high frequency power coil. The upper portion of the powder charge is melted first and the high frequency coil lowered until the powder is completely molten. During cooling the high frequency coil is raised slowly. These means also reduce the final nonviolent extrusion of large beads of metal through the ingot top during freezing. Better control of spitting and bead extrusion is obtained when melting is done under helium at. atmospheric pressure instead of in vacuo. The problem of reaction between silicon charge and crucible in practice is confined to the reaction between silicon and quartz. This2 apparently is: Si + SiO2 + 2SiO The part that this reaction plays in spitting has not been isolated for separate study. SiO is a volatile vapor at the melting point; of silicon and is released freely during melting in vacuo, but hardly at all in helium at atmospheric pressure. The cracking of ingots is a major difficulty in melting silicon, and its prevention requires special melting techniques or the addition of "toughening" agents such as aluminum or beryllium.&apos; The cracking of the ingots has been explained as being the result of the expansion that occurs upon freezing; although direct observation of freezing ingots reveals visible cracks on the surface only after a red heat has been reached, suggesting that cracking is the result of differential contraction of silicon and quartz. Silicon wets quartz, and the ingot adheres tightly to the crucible. Therefore as ingot and crucible cool, the two either have to pull apart, or at least one must crack. Surprisingly, in spite of the relative thinness of the quartz and the thickness of the ingot, the ingot and the crucible both crack. Microscopic and X-ray4 studies fail to show any plastic flow other than twinning in the ingots. Slow cooling fails to prevent cracking. Another possible solution to cracking is to weaken the crucible. Use of thin-walled crucibles finally led to success with fused quartz crucibles with a wall thickness of 0.25 to 0.50 mm. With such thin-walled fused quartz crucibles consistently uniform success is secured in producing sound ingots 30 mm in diam from the purest available grade of silicon (99.9+) without the use of any type of addition. Melts are made in the size range of 50 to 100 g. Omission of a deliberately added doping agent is not sufficient to insure pure ingots. The reaction of silicon with crucibles and the resultant solution of impurities in the silicon is well-established." In this laboratory, the presence of Al, Be, and Zr has been found spectroscopically in ingots melted in contact with alumina, beryllia, and zircon. The best crucible materials reported in the literature are MgO and SiO2. Use of MgO in this laboratory has resulted in a heavy deposit of magnesium on the furnace walls, showing that a reduction of the magnesia occurred and the resulting magnesium removed from the melt by volatilization. In the case of quartz, the silica is reduced and SiO liberated to deposit on the equipment walls. There probably is real danger that oxygen is dissolved in the ingot when either magnesia or silica is used as the crucible material. Preliminary analyses by Dean Walter in his vacuum unit in this laboratory6 indicate the presence of oxygen in undoped silicon melted in quartz.

Jan 1, 1953

By L. C. Raymond

Valuations in the mineral industry differ from those of other enterprises because mines and oil wells have a definite life so cannot be considered a perpetuity. This requires that in any mineral-property evaluation the recovery of invested capital is necessary during the life of the property. Capital write-offs for nonextractive industries are assumed to be continuously plowed back to sustain the operation and produce yields on the capital invested. The extractive or mineral industry, however, generally attempts to return to the investor both interest and principal during the life of a property. Normally this is done currently and the dividend includes both items. Where the mineral property possesses large reserves and the life factor approximates a perpetuity, the return on investment is generally comparable to that of industrial stocks. The valuation of a mineral property, at best, is based on educated estimates and judgment factors. This is particularly true as it relates to estimating selling prices over a long term or assessing the quality of management. Also, it is possible to make various assumptions as to rapidity of working out the deposit, varying time for start-up of operations, varying earning rates, so as to obtain different results with the same basic facts. Thus it is not surprising that two engineers, irrespective of their abilities, may not agree exactly even when given the same facts, but their results should be close enough to be used in establishing a fair value for trading purposes. The valuation is no better than the source of basic data and the soundness of judgment factors. Fundamentally the basic principles of mineral valuation are similar for base metals, sulfur, oil, or any other mineral. Each mineral, however, requires an engineer to have a knowledge of such factors as its occurrence, distribution, mining and processing methods, and marketing problems in order to gather and analyze all the facts and data that have a bearing on the earning potential of the property. Present Value of a Mineral Property In essence the present value of a mineral property is a sum of money in today&apos;s dollars that future income from the property are worth. It differs from the total anticipated earnings by the amount of the interest that the unrecouped investment could be expected to earn during the period of recoupment. Thus, if one could accurately estimate what a mineral property will earn during its life, after deducting all operating, administrative, capital, interest, and tax charges, the determination of present value would be a relatively simple mathematical calculation. Normally, where the expected life of the mineral property extends beyond 20 or 25 years, the discounted value of earnings beyond this period is relatively small. The petroleum industry generally discounts the annual cash flow of an operation rather than earnings since, for tax-saving purposes, earnings are kept

Jan 1, 1976

By John G. Baragwanath

THE September issue of the Engineering and Mining Journal carried an item regarding the Cercapuquio Mining Co. which was mentioned as a large producer of lead, zinc, and cadmium, situated near Huancayo, Peru. The paragraph caught my eye because I had not heard of the property in thirty years and I recollect all too well the circumstances of its accouchement. In 1916 1 was making my headquarters in the town of Huancayo, then the terminus of the Central Railway of Peru, and was examining mines and prospects in that general area for Cerro de Pasco. In the course of my work I became acquainted with an engaging and energetic "practical" miner named Balarin, a Dalmatian living in Huan¬cayo, and made numerous trips in his excellent company. One day Balarin came to the down-at-heels hostelry where I stopped and told me that a Cholo prospector, a character by the name of Jose, had just reached town and claimed to have made a discovery in a little known locality called Cercapuquio. Lead-silver, Balarin said, and showed me a sample of galena about the size of his fist. "Fine," I remarked. "When do we leave?"

Jan 1, 1947

By L. A. Norman

ANOTHER chapter in the history of Mother Lode mining is being written by operations in the Old Eureka mine near Sutter Creek, Amador County, California. During a two-year period (1938-1939), 85,517 tons of ore averaging 0.62 oz. gold per ton were mined and milled, as compared to the production of approximately 210,000 tons of 0.315-oz. gold ore during the preceding seven years. This is a repetition of mining history in the Mother Lode, where a period of prosperity has followed a long period of lean production. The location of this new ore in the hitherto unproductive hanging-wall greenstones and its mining and geological developments are most interesting. HISTORY OF THE OLD EUREKA MINE The Old Eureka mine, also known as the Hayward, Eureka, Hetty Green and Amador Consolidated, is in the most productive 10-mile length of the 120-mile long Mother Lode of California. The mine was first opened in 1852 with operations more or less continuous for the next 30 years. Production during this period amounted to $12,000,000 from an ore shoot 500 ft. long, which bottomed 1700 ft. below the surface. The shaft was continued as a prospect to 2065 ft. on the incline, where work was stopped in 1881. The mine was sold in 1916 by Hetty Green and the shaft deepened to the 3500-ft. level (3212 ft. vertically) by the new owners. Drifts were run on the 1700, 2100, 3000 and 3500-ft. levels, together with approximately 1500 ft. of crosscuts. No ore was found and work was abandoned in 1921. The present owners, the Central Eureka Mining Co., purchased the mine in 1924 after threatened litigation over rights to the rich ore shoot being mined from the lower levels of the Central Eureka mine on the south. Rehabilitation of the shaft commenced in 1926 and in 1930 mining on the old 2100-ft. level was started. While efforts of the previous owners had been directed for the most part toward the area south of the Old Eureka shaft and adjacent to the productive Central Eureka mine, the present owners started drifting northward on the old 2100-ft. level. On the 2000-ft., 2100 and 2300-ft. levels, drifts were run in part along the

Jan 1, 1939