Search Documents

By J. E. House, J. L. Drobnick, R. R. Swanson, D. W. Agers

The paper describes an improved process for the recovery, purification, and concentration of copper values from acidic dump leach liquors. The process employs a new liquid ion exchange material (LIX® 64 reagent) capable of separating copper values from iron and other impurities common to dump leach liquors in the typical pH range of 1.4-3.0. Properties and performance of the reagent are discussed. Design scale-up information for both pilot plants and commercial installations, including preliminary economics, are presented. Economic considerations include the production of electrolytic copper from the purified copper aqueous concentrate. INTRODUCTION Since the commercial acceptance of the liquid ion exchange process in the mineral processing industry, it has been predicted that a wide selection of chemical reagents to efficiently and economically separate many metals in solution under a wide range of conditions would be commercially available. Several years ago, General Mills began a basic research and development program to determine if it were possible to develop a reagent to extract economically metallic ion from existing process streams. Progress toward reaching this objective was reported in late 1963, when development of quantities of LIX -63 reagent, a highly selective reagent for the extraction of copper, was introduced. The properties of this reagent are described in a previous paper.' The development work with this reagent indicated that perhaps the largest potential application for a copper extractant, the treatment of acidic dump leach liquors, would not be economically possible with LIX-63 because of limitations of the reagent to extract copper below a pH of 3.0. The relatively small pH adjustment required with LIX-63 would result in a significant processing cost and the undesirable precipitation of ferric hydroxide from the liquor. This pointed to the need for another copper extractant which would extract copper from dump leach liquors without pH adjustment. General Mills was successful in synthesizing a molecule which does not have the pH limitation of the LIX-63, yet possesses the selectivity-solubility properties required of a metallic extractant. The resulting LIX-64 reagent broadens the pH range from which copper can be effectively extracted and separated from other metallic impurities. Of special significance is the fact that the reagent, LIX-64 was developed by combining the technical requirements of a specific problem in hydro-metallurgy with theoretical organic and physical chemical principles.

Jan 1, 1967

By R. E. Allen

ONE of the most unusual oil field engineering accomplishments of the past two years is the development and rapid advance in the directed drilling of wells. Directed drilling as referred to herein is the controlled steering of the drill stem in the required direction to a given location in the oil sand. The deliberate drifting of holes is an act so far removed from what has been considered good drilling practice that all of the old questions of correlation, drillability and production difficulties are revived. Only a few years ago, during the boom days of Seminole and Santa Fe Springs, the crooked-hole problem, as it was then called, occupied a primary position among the topics of the day in the fields of California and the Mid-Continent. The net result of all the discussion and study at that time was the conclusion that oil wells should be drilled with as little deviation from

Jan 1, 1933

By M. A. Elliott

The technology of gasifying coal to produce synthesis and pipeline gas has advanced significantly in the Past 20 to 30 years. This period has seen the extensive use of oxygen in coal gasification, the development of suspension gasification processes and fluidized-bed gasifiers, the operation of various gasification processes at elevated pressures, and operation of gasifiers under slagging conditions. These developments are discussed, and their application to commercial and pilot plant gasifiers is reviewed. Typical processes for synthesis gas production are described, and operating results are compared. Pipeline or high-Btu gas may be produced from coal either by catalytic conversion of synthesis gas to methane, or by the direct reaction of coal with hydrogen (hydrogasification) to produce a methane-rich gas. Neither of these methods has been applied commercially, but developments pertaining to each of them are reviewed, and general processing schemes are discussed. The use of coal as a raw material for manufacturing gas has a long and distinguished history. In fact, the gas industry began in the early 1800's when William Murdock demonstrated that it was feasible to produce and distribute gas made by retorting coal. Coal was used exclusively for gas manufacture until the middle of the 19th centruy, when Lowe invented the carbureted water gas process. In that process, coke was one of the raw materials used, so coal was still an important factor in gas manufacture. However the availability and relatively low cost of natural gas in the United States, and its widespread distribution by long-distance pipelines in recent years, has virtually eliminated the use of coal as a raw material for gas manufacture in this country. It should not be inferred from the foregoing that the technology of coal gasification has remained static in the United States and abroad. In fact, in the past two decades many new concepts have been developed in both the science and the technology of gasification. This progress has been a result of the considerable expansion in research on the fundamental chemistry and physics of gasification reactions, and in development work on gasification processes. This expansion in effort stems in part from increased interest in the use of gas as a raw material for the synthesis of chemicals and liquid fuels, and in part from the need to develop methods for gasifying coal and other solid fossil fuels to ensure a long-range supply of energy in the form of gaseous fuel. In these uses of gas, synthesis gas, a mixture of hydrogen and carbon monoxide in various proportions, is the starting material. It may be converted catalytically to gaseous and liquid hydrocarbons and other chemicals, or to hydrogen for use in hydrogenation or reduction reactions. Since coal is our most abundant fossil fuel, it is inevitable that one day it will regain its prominence as a raw material for gas manufacture. It is of interest, therefore, to consider the present status of gasification technology, directing attention particularly to advances made in recent years. Inasmuch as many comprehensive treatises l-3 and review4-7 of gasification technology are available, no attempt will be made in the present review to cover all processes in detail. Instead, the discussion will be concerned chiefly with typical processes embodying the advances that are most likely to be generally applied. ADVANCES IN GASIFICATION TECHNOLOGY For purposes of this discussion the starting point will be the conventional processes that were used for many years for the complete gasification of coal. These were: 1) carbonization in coke ovens followed by gasification of coke with air and steam in cyclic water-gas generators, and 2) fixed-bed air-blown producers. Both of these methods have obvious deficiencies when we consider that the ideal complete gasification process would be a single-stage, continuous

Jan 1, 1961

By Herty, C. H.

The effect of temperature on the physical properties of structural materials has been the subject of many investigations during the past decade. The literature on the effect of elevated temperatures. is voluminous, and during the last four years a great deal of experimental work has been carried out on the effect of low temperatures on the impact properties of steel. For many engineering purposes it is important to know the shock resistance of steels at low atmospheric temperatures, and with the ever-developing field of refrigeration and separation of materials at low temperatures, the normal limits of atmospheric temperature have been exceeded in practice. Iron and its alloys in the unnotched condition have a high impact strength at low temperatures, but in practice variations in type of notches result either from design or accidentally through scratches and surface or internal defects. A study of notched bar impact tests is, therefore, highly important to the engineer. A survey of the literature on low temperature impact testing indicates that chemical composition, heat treatment and method of testing have been the variables which have been considered in most previous work. In only a few instances has any mention of the steel- making method been mentioned and in these the comparison was between steel-making processes and not between steel-making methods on the same process. In view of the wide variations in impact properties at room temperature, in quench and strain ageing and in grain growth of steels of identical chemical composition, (by this is meant the usual five element analysis reported), it was felt

Jan 1, 1957

By AIME AIME

MANY interesting papers, opportunity of seeing o1d friends, and an exposition showing all that is latest in equipment, all were factors in bringing a large crowd to Detroit during "Metal Week," October 2-6. The Institute's Iron and Steel and Institute of Metals Divisions held technical sessions at the Statler Hotel on October 4 and 5, and that hotel was also headquarters for the American Society for Steel Treating and the American Society of Mechanical Engineers, both of which also had technical sessions. The American Welding Society and the Wire Association met at the Book-Cadillac Hotel, and the exposition was staged at Convention Hall, out Woodward Avenue. All in all it was a big week for men interested in metal working. One of them stated to your reporter on the train en route to Detroit that this was the one convention that he never missed, and doubtless others felt the same way about it.

Jan 1, 1933

By P. J. Potter

Practically all tin-base babbitt metals used in engine bearings are made to customers' specifications, which are many and varied. The copper ranges from 3 to 8 per cent. and the antimony from 4 to 13 per cent.; generally, the babbitt with lower copper content will contain from 4 to 8 per cent. antimony and that with higher copper will have from 7 to 13 per cent. antimony. The allowable lead content varies from 0.20 to 2.00 per cent. If a solder is used as a bonding material instead of tin, the resulting material in the finished bearing will have a higher lead content, but it would not be enough to bring the lead above specifica-tional limits. Impurities such as iron, arsenic and bismuth should be determined in the tin before using to insure a uniform and high-grade product. These points must be considered when segregating and grading the waste that comes from the finishing operations on lined bearings. Classification of SCRAP Because of the extremely rigid nature of most of the specifications for bearing linings it is necessary to use the purest of materials as a base for all compositions. The problem of handling secondary metals is confined almost entirely to the recovery of drosses, spills and turnings incident to the manufacturing operations. As a matter of convenience the waste or scrap may be divided into 10 grades, as follows: 1. Tin from pots where tinning operation is carried out. 2. Tin and babbitt spatters from babbitting operation. - 3. Tin skimmings combined with burned zinc chloride. 4. Borings and reamings. 5. Gates from die-cast bushings and bearings. 6. Drosses from die-cast pots, babbitt foundry pots, and pots in babbittiug room. 7. Babbitt with small amount of bronze from machining operations. 8. Babbitt and bronze borings. 9. Scrap bronze-back babbitt-lined bearings. I 10. Scrap die-cast bearings and bushings. A few of these grades of salvaged material have compositions that make it possible to determine beforehand where they may be used to

Jan 1, 1930

Jan 1, 1882

By L. Moyd, P. Moyd

The first commercially available portable gamma ray-neutron beryllium detector, the Rerylometer, was developed by the same group that developed the first practical portable scintillation counter, the Scintillo-meter. This group includes Professor George Brownell, of the Geology Department of the University of Manitoba in winnipeg, and his associates, K. I. Roulston, R. w. Pringle, and R. L. Funt, of the Physics and Engineering Departments of the University of Manitoba. A prototype model was tested in the field by Dr. Brownell during the summer of 1958. Commercial production was undertaken shortly thereafter by Nuclear Enterprises Ltd., of Winnipeg, and a license for manufacture and distribution in the U.S. was granted to Isotopes Specialties Co., of Burbank, California, a division of Nuclear Corporation of America. Early in 1959, we were retained by the 'Mining Division of Minerva Oil Co. to Legin a search throughout North America for minable deposits of beryllium, and to train members of their permanent staff to continue the program. The project included literature sur-veys, interviews with members of various federal, state, and provincial agencies, scanning of our own collection of suites of specimens from various mineral occurrences, and the examination of deposits in the field. The value of a beryllium detector to this program was obvious and arrangements were made to procure one as soon as possible, which resulted in our obtaining and using the first instrument that was produced commercially in the U. S. In addition to the commercially available Berylometer, Mr. William Vaughan and his associates, of the U. S. Geological Survey Geophysics Division, in Denver, have developed and tested several experimental instruments based on the same principles. DETECTOR Principles The detection of beryllium is based on the fact that "hard" gamma rays (1.6 MEV and geater), such as those produced by Antimony convert ordinary beryllium (Be9) to Be8 , with the release of a neutron. The neutrons are counted by a scintillator designed to favor neutron responses while suppressing those of gamma rays. 'The instrument is completely selective for beryllium. No other element can interfere. Instrunlentation The Rerylometer itself, which is cylindrical, is about 8 inches in diameter, 13 inches high, and weighs about 11 pounds. (Figs. 1, 2). The principal components include: 1. A disc of wax to moderate (or "thermalize") neutrons. 2. A boron-enriched polyester-zinc-sulphide fluorescent screen. This material produces strong flashes when struck by thermalized neutrons but only weak flashes from gamma rays. 3. A photomultiplier tube. 4. An electronic circuit, complete with one srnall 71/2-volt dry battery. The photomultiplier tube and electronic circuit convert neutron flashes to electrical impulses, but gamma ray effects are almost

Jan 1, 1961

By E. B. Johnson

Cleveland-Cliffs lron Co., which operates Marquette lron Mining Co.'s Republic mine, conducted a test whereby 35,000 tons of self-fluxed pellets were produced in the grate-kiln system from specular hematite flotation concentrates. A brief description of the pelletizing plant is presented along with pertinent operating details. Date is included which compare operating conditions and the chemical and physical properties of the green and fired pellets for the self-fluxing pelletizing test with the normal acid pelletizing operation. The success of self-fluxed sinter in enhancing the operation of the blast furnace during the past few years has reasonably led to the assumption that the use of self-fluxed pellets might result in even greater furnace efficiencies. A great share of development work in agglomeration has been directed towards techniques related to the production of self-fluxed pellets, but only a limited tonnage of self-fluxed pellets had been produced on a commercial scale until this past year when The Cleveland-Cliffs Iron Co. produced 35,000 tons of such pellets by the grate kiln system at the Republic mine during the period May 21-June 5, 1962. REPUBLIC'S GRATE-KILN PLANT The grate-kiln pelletizing process consists of four stages, namely: feed or balling circuit, traveling grate, rotary kiln and annular cooler (Fig. 1). The balling section is conventional and utilizes four 9x30-ft balling drums in closed circuit with 5x14-ft vibrating screens having 3/8-in. rod decks. The traveling grate is 12 ft wide by 126 ft long and has 14 windboxes — six in the drying section and eight in the preheat section. The rotary kiln is 15 ft ID shell and 114 ft long. The annular cooler is 40 ft in diameter and has 12 windboxes. The cooler is divided into two zones by a moveable curtain wall. The high temperature air from the first zone is used as secondary combustion air in the kiln. Normally the only heat supplied is through the burning of No. 6 oil in the single kiln burner. Hot gases pass counter to the pellet flow through the system. The exit gases from the kiln pass down draft through the preheat section through cyclones and are drawn through the drying bed prior to exiting via the stack. The temperatures are normally held within the following ranges: Kiln 2400-2445 °F Preheat 1850-1950°F Drying 480-520°F Exit gas 200°F Pellets 120°F The design capacity of the Republic mine grate-kiln system was 2500 Itpd. Sustained production in excess of 35% over design capacity has been achieved. No screening of the cooler product is practiced. PELLETIZING TEST CONDITIONS When a decision was made to proceed with a test at the Republic mine pelletizing plant to produce 35,000 tons of self-fluxed pellets, several potential failure factors had to be carefully considered. Research work on a batch and pilot plant scale indicated that the grate-kiln system at Republic would require some major changes in order to obtain optimum conditions. In many cases compromises were agreed upon as major equipment changes and revisions were not feasible. The pelletizing conditions which laboratory development tests revealed were required in order to insure successful production of self-fluxed pellets were: 1) Good mixing of limestone and concentrate and proper moisture control; 2) Higher gas flow rates in the preheat section than are normally used; 3) Higher preheat temperatures than normal; 4) Maximum kiln temperature 2350°F. There was just cause for concern about balling problems that might occur. Approximately 10% of dry pulverized limestone was to be added to the specular hematite concentrate just ahead of the Pekay mixers on the belt feeding the balling drum. Large scale

Jan 1, 1963

By Edna A. Dancy, Gerhard J. Derge

Jan 1, 1963

By P. E. Fitzgerald

ACIDIZING, as the terns is used in the petroleum production industry, involves the use of hydrochloric acid in predominantly limestone formations, resulting in the lowering of resistance offered to the flow of oil and gas through the oil-bearing formation, usually with resultant increased production. A number of articles have been written on the chemical treatment of oil and gas wells; a bibliography of these works will appear in Volume 123 of the Institute's TRANSACTIONS (1937), and a few other references are appended to this paper.

Jan 1, 1937

F. E. Thompson, Pottstown, Pa.: If Mr. Webster's endeavor to open up the subject of cast-iron should prove as prolific of results as did the discussion on " The Physics of Steel," he must certainly feel richly repaid. His remarks concerning the secretiveness and conservatism of the average foundry-man recall to my mind an instance of a blast-furnace which, for the last year, has been producing much foundry-iron. The manager, believing that much more of his product could be used in the foundry than the foundry-men were will-

Jan 1, 1896

By John Freeman

THE die pressing of brass may be described as a method of producing irregularly shaped parts of brass and other copper alloys by hot deformation in a die under pressure. Die pressing of brass was first developed as an improvement on sand castings in order to obtain irregularly shaped articles of brass with superior surfaces, a closer tolerance in dimensions, a denser structure, freedom from porosity and elimination of the relatively large amount of scrap invariably attached to sand castings. The freedom from sandy surfaces with consequent greater tool life in machining operations was also recognized as well as elimination of losses due to the uncovering of blowholes in machining operations. Die pressing also gave alloys of superior strength. Die pressings today are made from extruded rod or shapes, according to design of the part to be made. The greater number of pressings are made from round rod, because of its relatively lower cost and ease of handling. The rod is first sheared or sawed into desired lengths, the diameter of rod used and length of "slug" or "rivet" depending upon ultimate weight and shape of the die-pressed part to be made and design of die. The dimensions of the slug are figured so as to give the, minimum amount of scrap to be sheared from the pressing as it comes from the-die. Extruded shapes having I, T or X sections are often used when the finished part is to have a similar shape or heavy sections are joined by relatively light sections of considerable length. A rod bent in the shape of a U is also used on occasion, for similar reasons. Proper shearing of the slugs is of considerable importance. The sheared ends of the slugs should be as flat and straight as possible. Improperly sheared ends having an angle to the axis of the bar or a rough, uneven surface are liable to give folds or laps in the finished pressing and proportionately high rejections. The property of shearing varies considerably with different alloys and should be considered in the selection of a material for a given part. Where satisfactory shearing is not possible, the slugs may be cut from the bar by power saws. Extruded

Jan 1, 1931

LOCAL COMMITTEE OF ARRANGEMENTS. Major J. W. Powell, Chairman; F. P. Dewey. Secretary; S. F. Emmons, A. S. Hewitt, J. P- Hilgard, Charles Knap, and F. W. Taylor. THE opening session was held in the hall of the new National Museum, on Tuesday evening, February 21st. President Metcalf introduced General W. T. Sherman, one of the Regents of the Smithsonian Institution, who read the following address: ADDRESS OF GENERAL SHERMAN. MR. PRESIDENT AND GENTLEMEN : I have been invited to meet you here this evening to extend to you the cordial greeting of the regents of the Smithsonian Institution, and to assure you that they are most happy to have it in their power to place at your disposal this beautiful hall, dedicated to science and art. This National Museum is the property of the United States, of which the regents of the Smithsonian are simply the custodians, and the board has delegated to its secretary, Professor Baird, the right to extend its use to the National Academy of Sciences and like kindred societies, among which we are glad to class the Institute of Mining Engineers. It is eminently fit that you should meet here at this, the nation's capital, under a roof partly your own, devoted to natural sciences, and in the shadow of the Smithsonian, founded for the exclusive purpose of collecting and diffusing knowledge among men. Of all the workers employed on earth no single class seem to me more worthy the respect of their fellows than those who seek beneath the surface for the useful minerals and metals which contribute so largely to the wealth and comfort of mankind. In no branch of human industry does intelligence come so immediately in contact with labor. To the mining engineer chemistry, mineralogy, and geology are as reading, writing, and arithmetic to the merchant;

Jan 1, 1882

By Robert B. Fulton

The use of industrial minerals by the chemical industry as raw materials for manufacturing and in processing spans a wide assortment of minerals. This chapter aims to supplement rather than duplicate the commodity chapters. Its objective, to describe the uses of industrial minerals in the manufacture of chemicals, is attained by considering minerals used by the chemical industry in terms of the chemical element required and by giving particular emphasis to market factors. The mineral aspect, which is covered in the commodity chapters, is subordinated and attention is focused on the chemical and market aspects. Condensing this broad subject into a few pages permits treating only the most important elements derived from industrial minerals. The elements derived from petroleum, hydrogen and carbon, which quantitatively dominate as raw materials for the chemical industry, are omitted, as are the metallic elements and the minerals covered in other "use" chapters such as phosphorous, potash, and nitrogen for fertilizers and titanium dioxide for pigments. After eliminating on this basis, our definition leaves six elements of major importance: boron, bromine, chlorine, fluorine, sodium, and sulfur. These elements are treated individually under separate headings. Salt brines have particular importance as raw material sources for the chemical industry as shown in Table 1 "Salt Brine Derivatives" (Anon., 1967), which charts the chemical compounds derived from four types of brines: (1) Owens Lake type brines which are sources of boron and sodium compounds; (2) Midland type brines from which bromine, iodine, and chlorides of calcium, magnesium, potassium, and sodium are derived; (3) Searles Lake type yielding boron, bromine, lithium, magnesium, potassium, and sodium compounds; and (4) Silver Peak type produced mainly for lithium. Table 2 (Jones, 1973) affords an overview of the chief industrial minerals, the chemical products derived from them, and end uses of the products.

Jan 1, 1975

By F. F. Skiba, P. J. Root

A mathematical model has been used to investigate crossflow effects in a stratified reservoir during an idealized displacement process. A process in which one incompressible fluid displaces completely another incompressible fluid of the same density and viscosity was considered. The reservoir was assumed to be composed of homogeneous layers which are discrete but interconnected. Approximate five-spot flow geometry was simulated by arranging two pie-shaped cylindrical (two-dimensional) wedges in series. Some of the common production methods rely, for their effectiveness, on the fact that the formation consists of isolated strata. This is particularly true of selective plugging and single-zone production-injection methods. The effectiveness of these techniques for several cases in which adjacent strata are in communication has been evaluated. The usual production-injection schemes for fluid injection processes involve using the same completion interval in both the production and the injection wells. The efficiency of this, as well as alternative productioz-injection procedures has been examined for some cases involving communicating strata. INTRODUCTION The performance of many fluid injection projects is marred by early breakthrough and by production of a high percentage of the displacing phase after breakthrough. This channeling effect, if it occurs in reservoirs which have large permeability variations, is often explained on the basis of a model composed of discrete, isolated strata. Corrective or preventive measures based on this same model are also common. The behavior of stratified models has been the subject of considerable study. An excellent review of the early literature was given by Seba.1 Studies of the depletion performance have since been made for continuous, unrestricted communication between strata2-4 and for production from one permeable bed in continuous but restricted communication with an adjacent permeable bed.5,6 Model studies of displacement processes in stratified systems with crossflow also have been reprted.7-12 Finally, methods which account for crossflow have been developed for computing displacement behavior in stratified systems.13,14 Most methods for controlling or preventing channeling involve some change in the interval open to production and/or injection. Although many variations of the selective completion problem have been studied in regard to the depletion of a reservoir, little attention has been given to the behavior of a displacement process under similar conditions. Sebal used a resistance network model to study the performance of a process in which one incompressible fluid displaces an identical fluid from a linear, stratified reservoir. He investigated the possibility of improving the vertical coverage by limiting the completion interval of the production well. This investigation deals with techniques in which selective completion of the production and/or the injection wells is used in an attempt to control channeling. At one extreme, selective plugging and single-zone isolation (assuming perfect execution) should be successful if the reservoir is actually made up of independent strata. At the other extreme, they can hardly be expected to be successful if the channeling is caused by a mechanism in which stratification effects are negligible even though there are extreme variations in the formation permeability and/or the injectivity profile of the wells is not uniform. By contrast, it is difficult to anticipate the effect that the amount of communication between the beds of a stratified system will have on the efficiency of selective completion techniques. The objective of this study is the quantitative determination of the effect of communication on the behavior of some particular stratified systems which will at least lead to qualitative conclusions.

Jan 1, 1966

By DR. SAMUEL B. CHRISTY

? THE man is always greater than his work.? The training of the men who are to develop the mineral resources of the world is the most important problem connected with mining engineering. It becomes ever more important to civilization as the mineral wealth of the earth approaches exhaustion. I have therefore decided to consider a few of the more important problems arising in the training of the mining engineer, and especially those arising in America. THE PECULIAR NATURE OF MINERAL WEALTH. Mining and Agriculture are the two fundamental arts. Without the latter our existence would be precarious; without the former, our civilization impossible. Agriculture furnishes that regular supply of food and raiment which leads to the growth of large communities in which cultivated leisure first becomes possible; while raining furnishes the metallic thread from which is woven that complex fabric we call civilization. But in these two arts the conditions for success are widely different. Most of the crops that the farmer reaps may be harvested year after year, and the proper fertilizers being added, he may continue the annual harvest indefinitely, while, as a result of cultivation, his farm becomes yearly more valuable. But the crop the miner reaps can be harvested but once in the history of the race. Our mineral wealth has taken unknown ages to mature in the bosom of the earth. The ripened fruit can be plucked but once. There are no fertilizers for worked out mines. It never pays to work over a mine that has been

Sep 1, 1905

By S. E. Bretherton

This title introduces the subject I wish to describe to my fellow members, very few of whom, I 'hope, have ever had as much trouble with the smelting of ore containing much zinc, either in the lead blast furnace or the matting furnace, as circumstances have forced upon me: First, for several years in Leadville, Colo., after the sulphide ores containing zinc had been developed with greater depth and were sold to the intereats with which I was connected for smelt-ing in the blast furnace for the recovery of the lead, silver, and gold; then, in New Mexico and Arizona, where the principal source of ore supply for our custom smelter was from miners who sent most of their product in the form of concentrates, which we briquetted and smelted in the blast furnace, producing a matte containing copper, silver, and gold, for which we were paid; together with some zinc and lead, which was penalized if in excess of a maximum base set by the refinery to which we sold our copper matte; last, but not least, my experience in Shasta county, Gal., where for the sake of recovering $13 per ton value in copper, silver, and gold, I have smelted ore containing as high as 40 per cent. zinc (the last 18,951 tons smelted averaged 15 3/10 per cent. zinc) which we not only lost, but which it cost us money to lose. After such an experience, and knowing that, instead of being worth only $13 per ton, such 15 per cent. zinc ore should be worth about $30, including zinc at the present market value, the question of recovering the zinc in a profitable manner from such ore became very interesting to me. During several years' time I sent samples, of from 5 to 1,200 lb. each, to be tested by the different best-known zinc-recovery plants, and experimented with several processes proposed by others for the treatment of such ore, with but little encouragement, until I

Jan 1, 1914

By H. L. Miaw, A. M. Gaudin, D. W. Fuerstenau

A quantitative method for evaluating density of slime coatings has been developed and applied to formation of iron oxide slime coatings on quartz and on corundum. Slime coating density is related to flotation recovery and to properties of the electrical double layer at mineral surfaces. IN spite of considerable study, the nature of slime coatings in flotation is still not completely understood. However, phenomena that control floc-culation and dispersion of colloidal systems are now interpreted in terms of electrical double layers.",' Colloids will flocculate even though the particles carry the same charge, but when two dispersed colloids of opposite charge are mixed. flocculation ensues even more rapidly. Analogous phenomena seem responsible for slime coating on minerals in flotation systems. To shed new light on the issue it was considered desirable to devise a tool that would measure slime coatings. The usual method has been to examine photographs of presumably representative surfaces, after. an intervening washing in running water. But such an examination is non-quantitative, and the changes in chemical environment represented by the washing may have removed the slime coatings that existed during flotation. To provide the possibility for a correlation with electrical double layer phenomena, the experiments were made with quartz, corundum, and iron oxide, for which elec-trokinetic data are available.'-" Since the properties of the electrical double layers of these oxides depend on the pH of the solution, pH will be the most important variable. Furthermore, because the zero point of charge for silica, iron oxide, and alumina occurs at pH 3.7, 8, and 9.5, respectively, the relative charge on the slime and mineral can be changed over wide ranges. Because of its practical importance in quartz flotation, iron oxide powder was chosen as the slime. Also, its uniform composition, contrasting color, and ease of analysis make experimentation simple. In this investigation, correlation was sought between the effect on flotation recovery of slime addition and slime coating density. Materials and Methods Details are available in a thesis by Miaw." The quartz was selected from pure Brazilian crystalline quartz, crushed, sized (65/150 mesh) acid-cleaned, washed, and stored in conductivity water. The corundum (synthetic alumina of high purity prepared by Linde Co., Chicago) was crushed, sized (65/100 mesh) deslimed, boiled in nitric acid, washed, and stored in conductivity water. The iron oxide slime, reagent-grade ferric oxide (—400 mesh) from Allied Chemical & Dye Corp., was heated to 160°C, cooled, and stored in a vacuum desiccator. In the electron microscope the slime particles appeared to be about 0.3µ in size, but their large specific surface (87,900 cm per g, by gas-adsorption method, using krypton) suggests that the actual particles are smaller than 0.3r. Had they been perfect nonporous spheres, they would have had a diameter of 0.13µ.

Jan 1, 1959

By A. C. Dorenfeld

CHANGES in circuits are often made in milling operations. At the same time that these changes are being evaluated the ores are changing. Even from the same mine, the ore is usually variable as to amount and type of mineral content, degree of association of valuable and gangue minerals, amount and types of soluble salts, hardness, etc. The question then arises whether any small differences in results, after changes have been made in the various circuits, are really due to these changes or whether the variability of the ore can account for those differences. Statistical evaluation provides one method of answering the question that arises so often in beneficiation studies: Did changed results come about because of changed process, or did ore variation cause the change? In this case, data were available for statistical analysis from an operating period of 42 months, representing treatment of approximately 1 million tons of ore. During this period there had been two flowsheet changes: 1) regrind of the zinc circuit middlings was introduced, and 2) alcohol- pine oil frother mixture was substituted for cresylic acid-pine oil frother mixture. Findings are in Table I.

Jan 10, 1954