Search Documents

By J. B. Wagner, p. Hembree

The iron tracer diffusion coefficient of umstite has been measured at 110(fC across the phase field and at a single composition at 800°C. Assuming a simple cation vacancy model the tracer diffusion coefficient was found to be a linear function of the cation vacancy concentration at 1100°C. The equation is D = 3 x 20 29 where denotes the concentration of vacancies in numbers per cc. The tracer work at 800°C was carried out to investigate the reported "pinning" of tracer to the wustite surface at low temperatures. No evidence for the "pinning" of the tracer was found at 800°C in COz-CO gas mixtures. HIMMEL, Mehl, and Birchenall,&apos; Carter and Richardson,2 and Desmarescaux and La combe3 have measured the diffusion of iron tracer in wustite at several temperatures and compositions. The present work was undertaken to extend the measurements over a large composition range at 1100°C and to resolve certain apparent discrepancies in the data, expecially at lower temperatures. EXPERIMENTAL Wustite was prepared by oxidizing rectangular iron plates* in C02-CO mixtures. The samples were •The iron was supplied by the Battelle Memorial Institute courtesy of the American Iron and Steel Institute. The analysis is presented in Table I. quenched. Due to the inward flow of cation vacancies during oxidation, the center of the sample contained a thin void. The edges of the wustite slab were sanded until the sample could be split into two parts. Each part was then sanded on the front and back flat area until a smooth surface was obtained. The specimens were then replaced in the furnace and equilibrated at llOO°C in a predetermined COa-CO mixture by methods described elsewhere.4"6 The specimens were again quenched and the surfaces were lightly sanded to remove any roughness following the first equilibration. The specimens were then reequi lib rated in the same C02-CO mixture for thirty minutes in order to relieve any mechanical damage on the surface due to the polishing. The specimens were then quenched and the tracer was applied by an electroplating technique. The work of Carter and ~ichardson&apos; demonstrated that there was no systematic difference in the iron tracer diffusion coefficient in wustite if the tracer was plated, dried, or evaporated on the specimen. In the present study a piece of filter paper was saturated with an iron chloride solution of pH <* 3 that contained the tracer FeS5. The wustite was placed on the filter paper and made the cathode. A current density of 0.4 to 0.6 ma per sq cm was passed for about five to ten minutes. The thickness of the tracer layer was estimated to be about 7 x lom6 cm. This estimate was made by considering the area plated, the current flow, and time for plating and the activity of the iron in the plating solution. Different areas of the specimen were counted using a collimator to determine the uniformity of the tracer. Any specimen which exhibited a variation from the initial count rate (about 1500 cpm) by more than 15 pct was rejected. An estimate of the time necessary to convert the thin layer of iron tracer to wustite was made using the data of Pettit and wagner." he estimated time was 1 sec at 1100°C assuming linear oxidation kinetics. The shortest diffusion anneals were 1800 sec. The samples were suspended in the hot zone of a furnace by two platinum wires. Two separate specimens were run at the same time. Only the edges of each sample were in contact with the wires. The C02-CO gas of the same composition as that used in the pre-diffusion anneals flowed freely around the samples at a linear velocity of 0.9 cm per sec. To initiate a run, the specimens were lowered from the cold zone of a furnace to the hot zone by a magnetic lowering device." bout 60 sec were required for lowering. To terminate a run, the sample was withdrawn from the hot zone to the cold zone. Time zero for the beginning of the experiment was taken when the sample blended into the red glow of the furnace and conversely for the end of the experiment. The surface decrease method of measuring the tracer diffusion coefficient was used to collect the data. This method requires that counting geometry be reproducible because the specimen is counted before the diffusion anneal and after the anneal. A special jig was constructed for each specimen so the specimen could be removed from the jig and returned to the jig such that the well geometry was reproducible.

Jan 1, 1970

By William Hilliard

IN any manufacturing business, it is of vital importance that the management should know the exact cost of the units of production. Without such knowledge, a company can sell blindly in the open market, obtaining the best prices it can in competition with other firms, and manage perhaps to continue in business for a time; but at any moment, and especially in a period of falling prices, such a firm is at a loss to know exactly at what point it can sell at a profit and exactly how much it is losing per unit if it sells below that point. Furthermore, it is necessary not simply to know the exact total cost per unit, but to know definitely all the different-factors which enter into that cost. A firm manufacturing pocket knives had been doing a profitable business for many years when it began to earn smaller and smaller profits, until there was scarcely any profit at all being realized. Being unable to determine exactly what its future policy should be, it called in experts who studied the past records carefully and followed out for a period a better cost, system. Investigation then showed that on several different kinds of knives in common use, a small profit per unit was being made. On a number of special kinds of knives, of which the firm was very proud, it had been forced to cut prices under the pressure of outside competition and had believed that a small profit per unit was still being made on that product, while a detailed cost analysis showed that a loss was being incurred on each knife of that kind produced. It then became clear that the company must either give up the special line and concentrate wholly on the cheaper knives and extend their sales to territory not yet developed; or expand its plant and produce more of the higher grade knives and thus lower the cost per unit enough to make money on the higher grade knives also, if conditions warranted such expansion. Investigation revealed that the market for large quantities of the high-grade -knives was decidedly uncertain and that the most promising move would be to manufacture only the less expensive knives on a larger scale. That plan was carried out and the concern began again to make a better profit.

Jan 1, 1932

By B. M. Larsen

NEVER having actually tried to engage in the systematic education of anyone, and having little direct knowledge of the practical problems and limitations in the field of education, I can pose only as a "nonexpert" in this field, one whose ideas are to be regarded as personal opinions. The necessity for compromise between educational ideals and the practical limitations of time, money, and mental capacities of both student and teacher is evident in the preparation of an end product that we may regard with a reasonable degree of conviction as a professional engineer. We need to do so many things. The engineering student must have a clear understanding of the basic sciences; he should develop manual skills and co-ordination; he should speak and write the language with simple clarity and directness; he should gather knowledge of a special field; and, he should be educated for living in a broad ..

Jan 1, 1948

By C. E. MACQUICC

WITHIN a period considerably less than two decades, the engineering view of alloy steels has greatly changed-both as to their composition, and applications. Inasmuch as the elements used in manufacturing alloy steels are substantially the same as those which have been used for the past two or three generations, a statement like the foregoing may reasonably call for some explanation. The first commercial use of alloy steels in this country dates back to the sixties of the last century, when one of the earliest alloy steel patents, covering the use of chromium, was taken out by Bauer. About ten years later, German and French toolmakers began to introduce tungsten into tool steels. Developments along this line were more or less static for 25 years or more, the tool steel, compositions progressing along lines worked out by Mushet and one or two others in Europe. The next step in advance, made by Taylor and White inn the late nineties, consisted of heat-treating the alloy steels to enable much higher cutting speeds, thus introducing what soon became known as "rapid" or "high-speed" steels. All these developments being aimed toward the improvement of cutting tools, the compositions made were essentially of a hard, brittle nature. Following a different line of development started in the seventies, naval ordnance material began to embrace the nickel steels. These were rapidly popularized, became, and still are, with the addition of one or more elements, as chromium, molybdenum, vanadium, standard for heat-treated armor plate. During that period, however, no notable uses were made of alloy steels for engine parts or other high-stress parts where they are now considered indispensable; moreover, the present-day use of metals in the chemical industries was probably not even imagined. After the turn of the century, the necessity for making heavy-duty. machine parts, and especially the develop¬ment of the automobile, caused alloy steels to rapidly supplant plain carbon steels for engineering purposes.

Jan 1, 1930

By Anthony Anable

THE definite trend to stricter specifications with respect to hydraulic concrete has become increasingly manifest in the last six years or so; but it remained for the vast reclamation projects of the Bureau of Recla-mation of the Department of the Interior of the last few years to focus attention on this trend, and to demonstrate how thousands of tons of concrete-making aggregates can be produced continuously and auto-matically with a control of fineness comparable with that obtained with small samples in well equipped private and governmental laboratories. Pioneer work in this direction was done, to be sure, by private com-panies, notably the Kaiser Paving Co. of San Francisco, prior to the present vast public works program. Then in 1931 came the first great, aggregates-preparation plant of the Six Companies, Inc. to supply construction materials for Boulder Dam&apos; in Nevada, and now, in 1936, the aggregates plant of the Mason-Walsh-Atkinson-Kier Co., general con-tractors on the Grand Coulee dam in Washington. At Boulder dam and to an even greater degree at Grand Coulee dam, sand production is recognized as probably the most important single element affecting the physical characteristics of the concrete. For in the construction of dams accurate grading of the fine aggregate has consider-able bearing on the attainment of a uniform and homogeneous concrete of a high degree of workability and placeability and, at the same time, combining high density and low cement content. Low cement content is of value not only from the standpoint of economy but also because the use of an unnecessarily rich concrete causes certain undesirable characteristics to develop. This paper will relate how at Grand Coulee dam methods that are more advanced than ever before are producing four sizes of gravel and a sand having a fineness modulus of 2.5-3.0. The design capacity is 1000 tons an hour. Significantly, the methods and equipment employed are broadly those that have been used for a generation in metallurgical mills for accurately sizing and grading both precious

Jan 1, 1936

By THOMAS J. CLIFFORD

IN 1926, finer grinding began to be a feature of the milling practice of the Southeast Missouri lead district. Nothing since the adoption of flotation has caused greater changes and greater improvement in results. The trend toward finer grinding, with the consequent discarding of tailing at finer sizes, and consequent lower assays in lead, continued to progress until 1931, when the abnormally low price of lead brought a halt: that is, the better metallurgical results obtained would not offset the increased costs due to higher power and necessary maintenance. Since 1931 a slight tendency toward the discard of coarser tailing has taken place. , In 1926, larger rod mills i.12 ft. 1 in. by 6 ft. 6 in.) than any previously used in the district were installed in cue plant, and a new primary crushing plant, of greater capacity was built. This combination demonstrated immediately the better metallurgical results obtainable by finer grinding and all the mills now running have adopted the practice.

Jan 1, 1934

By R. Ruka, E. A. Gulbransen

ONE of the interesting questions in the understanding of the reaction of iron with oxygen is the kinetics and the mechanism of the crystal structure changes occurring in the formation and breakdown of the oxide film. In a recent work&apos; the electron diffraction method was applied to the study of the solid phase reactions occurring internally in the oxide film on iron above 570°C and under vacuum conditions. The higher oxides which form under oxidizing conditions are reduced internally by the diffusion of iron into the oxide leaving the bulk of the oxide FeO (wüstite). This paper will ask and consider three questions. These are: (1) What is the nature of the depressed transformation temperature for the Fe3O4 + Fe ? 4Fe0 reaction in very thin oxide films?; (2) What is the mechanism of the forward transformation of Fe3O4 to FeO at or near 570°C?; and (3) What is the nature and mechanism of the slow reverse transformation of FeO to Fe3O4 and Fe below 570°C?. The composition of the oxide as well as its electrical, magnetic, mechanical, and chemical properties depends upon the kinetics of these reactions. Literature Survey The composition of the oxide film on pure iron at temperatures up to 570°C has been studied extensively by the electron diffraction method. Nelson,&apos; Jackson and Quarrell,3 and Gulbransen and Hick-man4 have shown that Fe3O4 and a-Fe2O8 are formed in the temperature range of 225" to 570°C, while y-Fe,O, is most likely formed below 225°C for long oxidation times. In very thin films FeO (wüstite) is found to form at temperatures as low as 400°C, and its existence depends essentially upon the extent of initial oxidation. FeO is not found in the formation of thick films below 570°C. On the other hand X-ray5 and micrographic8 studies show that Fe3O4 may exist as the main com-ponent in thick films up to 650°C, well above the equilibrium temperature for the reaction Fe3O4 + Fe ? 4FeO. The kinetics of the forward and reverse trans-formations of the reaction Fe3O4 + Fe ? 4FeO have not been studied in oxide films. However, analysis of the data of Gulbransen and Hickman4 on the heat-ing and cooling of iron oxide films of known thick-nesses in high vacua shows that the forward reac-tion proceeds rapidly even for a 4000 A film at temperatures of 575" to 600°C. The reverse reaction or decomposition of wüstite (FeO) occurs at tem-peratures below 450°C. Thus, there appears to be a slow process in the decomposition which is in marked contrast to the rapid forward reaction. The decomposition of a bulk sample of FeO free from the metal has been studied extensively by Chaudron, Benard and coworkers using the micro-graphic, X-ray diffraction, and thermomagnetic methods. Chaudron7,8 first observed that the de-composition of FeO (wüstite) below 570°C occurs by the reaction 4FeO ? Fe3O4 + Fe. Later work by Chaudron and Forestier5 showed that the rate of de-

Jan 1, 1951

By N. Tiner

The mechanical properties of magnesium-alloy castings are greatly improved by grain refinement, and at present considerable attention is being paid to methods of obtaining fine-grained castings. One method of achieving this end is the use of proper melting and superheating techniques. These have been employed com-rnercially to a great extent, but no comprehensive study of the subject appears to have been published at present. Numerous investigations found in the literature include some reference to superheating techniques,1"4 and Achenbach, Nippcr and Piwowarsky,% ased principally on thermal analysis, ascribe the grain-refilling action of superheating to the influence of solid foreign particles or dissolved gases present in the melt upon the course of crystallization. The primary purpose of this paper is to present the principal facts concerning the cffect of superheating on grain size of magilesium alloys. .ittempts are also made to explain the experimental results in terms of a general hypothesis. The investigations are limited chiefly to common commercial casting alloys. In order to carry on this work, it was necessary to determine the factors influencing grain size and to develop a proper technique for the preparation of samples. Thc preliminary tests made by the author indicated that the grain size of magnesium alloys resulting from the solidification of a melt is determined by alloy composition, presence of impurities, rate of cooling during solidification, thermal history of the melt and to some extent the structure of the charge used. The rate of cooling is in turn dependent upon the mass of the melt, pouring temperature, and dimensions, properties and temperature of the mold into which the melt is poured. The final grain size of the alloys is still further modified by heat-treatment subsequent to casting. It is not within the scope of the present paper to discuss all of these factors, and it would suffice to note here that when equal amounts of magnesium alloys are prepared from the same alloying materials, melted in graphite crucibles under the same thermal conditions, then cast into graphite molds at a constant temperature, the resultant solids have the same grain size. By maintaining all other factors constant, it is thus possible to vary thermal conditions of a melt and to examine the grain size of resultant castings. Preparation of Samples and Grain-size TestiNg The alloys investigated in this paper were taken from ingots made by Permanente the Or or prepared by the author with pure carbothermic magnesium and necessary alloying elements. Melting was carried out under a flux in a graphite crucible heated uniformly by an

Jan 1, 1946

By N. Tiner

The mechanical properties of magnesium-alloy castings are greatly improved by grain refinement, and at present considerable attention is being paid to methods of obtaining fine-grained castings. One method of achieving this end is the use of proper melting and superheating techniques. These have been employed com-rnercially to a great extent, but no comprehensive study of the subject appears to have been published at present. Numerous investigations found in the literature include some reference to superheating techniques,1"4 and Achenbach, Nippcr and Piwowarsky,% ased principally on thermal analysis, ascribe the grain-refilling action of superheating to the influence of solid foreign particles or dissolved gases present in the melt upon the course of crystallization. The primary purpose of this paper is to present the principal facts concerning the cffect of superheating on grain size of magilesium alloys. .ittempts are also made to explain the experimental results in terms of a general hypothesis. The investigations are limited chiefly to common commercial casting alloys. In order to carry on this work, it was necessary to determine the factors influencing grain size and to develop a proper technique for the preparation of samples. Thc preliminary tests made by the author indicated that the grain size of magnesium alloys resulting from the solidification of a melt is determined by alloy composition, presence of impurities, rate of cooling during solidification, thermal history of the melt and to some extent the structure of the charge used. The rate of cooling is in turn dependent upon the mass of the melt, pouring temperature, and dimensions, properties and temperature of the mold into which the melt is poured. The final grain size of the alloys is still further modified by heat-treatment subsequent to casting. It is not within the scope of the present paper to discuss all of these factors, and it would suffice to note here that when equal amounts of magnesium alloys are prepared from the same alloying materials, melted in graphite crucibles under the same thermal conditions, then cast into graphite molds at a constant temperature, the resultant solids have the same grain size. By maintaining all other factors constant, it is thus possible to vary thermal conditions of a melt and to examine the grain size of resultant castings. Preparation of Samples and Grain-size TestiNg The alloys investigated in this paper were taken from ingots made by Permanente the Or or prepared by the author with pure carbothermic magnesium and necessary alloying elements. Melting was carried out under a flux in a graphite crucible heated uniformly by an

Jan 1, 1946

By Francis L. Bosqui

The following paper embodies a report which I made on the filter-press treatment of slimes at the Liberty Bell mine, Telluride, Colo. At the time this report was submitted, the management deemed it wiser to defer the installation of so costly a plant as the one required, in the hope that some of the many investigators in the field might soon evolve a cheaper and more perfect method of slimes-treatment, and one better suited to the conditions at Telluride. The Liberty Bell ore consists essentially of quartz and clay, with iron pyrites disseminated through the quartz in very fine particles. There is considerable iron and manganese stain in some of the ore, the latter especially in the clays, which are sometimes quite black. Occasionally particles of galena, zincblende, gray copper and a few other minerals are seen, but they are comparatively rare, and not in sufficient quantity to affect considerations of treatment. Free gold is occasionally seen in the quartz, and one or two instances of mire silver have been observed. The milling-plant consists of an 80-stamp amalgamating mill which crushes through 20-mesh screens; 20 Wilfley concentrating tables, taking out, in iron sulphides, about 2 per cent. of the total ore crushed; and a cyanide plant consisting of two tiers of 33 ft. vats, five in each tier, fed by revolving pipe-die tributers. The slimes overflow from the upper settling tanks through gates with adjustable outlets, and thence to a large canvas-plant, which efects only a small saving. This slimes product, of which about 100 tons escape per day (or 38 per cent. of the total ore crushed), contains about 3 per cent. of dry solids. Of this approximately 93 per cent. will pass a 200-mesh screen. The slimes range in value between $3.90 and $4.87 per ton, the values being about equally distributed between gold and silver. The actual averages for ore and slimes during the years 1900-

Jan 1, 1904

By W. E. Wrather

SERIOUS consideration was given by the Petroleum Division to a wide variety of subjects, during six busy sessions at the Annual Meeting. Beginning with a joint session on engineering research and production engineering, Tuesday afternoon, conducted by E. A. Stephenson and H. C. Fowler, problems of petroleum technology, domestic and foreign production, proved oil re- serves, economics, and stabilization were mooied almost without interruption until nearly everyone was "talked out,&apos; and the meeting was adjourned at the end of the annual Petroleum Division dinner, late Thursday night.

Jan 1, 1933

Jan 1, 1970

By ALBERT C. RUBEL

RECENT developments in the use of the core barrel in rotary drilling have led to its wide application in all types of development. Its use is essential to the wild-catter and a valuable guide and check even in the most closely developed areas. A perfect core would be an unbroken sample of formation whose length is equal to the amount of hole made by the core barrel, whose diameter is great enough to show the lithologic character, texture and attitude of the material encountered, whose formation is so unaltered in character and so free of contamination from outside sources that it represents a true and complete sample of the formation penetrated. From such a core it would be possible to determine the lithologic character and economic importance of the formation, whether it is oil bearing or barren, the nature and attitude of the sands and shale bodies, valuable fossil evidence and other points which would assist in the correlation or in the selection of suitable points for water shut off or production.

Jan 1, 1924

By C. H. White

Discussion of a Paper by Mr. C. H. White, read at the Atlantic City Meeting, February, 1904. (Annual Meeting, February, 1005.) ARTHUR JARMAN, Sydney, New South Wales, Australia (communication to the Secretary*) : All designs for modern metal¬lurgical and chemical laboratories should provide each student&apos;s desk with a hood or cupboard for the removal of fumes, but I doubt the advisability of placing air-baths and similar apparatus close to the hot plate. It seems to me that unless the draft be exceptionally strong the fumes from ordinary wet assay work will corrode the iron-work of the fittings, in which case the baths would have to be removed to a general desk in order to lighten the work of the laboratory attendant. Since the laboratory described by Mr. White has been in use for two years, I should like to ask if any inconvenience has resulted from this corrosion. If not, it is certainly an important improvement to have the air-baths and similar apparatus placed -on the student&apos;s desk. The hoods described by Mr. White are supplied with a good draft by means of a fan, which gives them a great advantage over those at the metallurgical laboratory at the University, Sydney, in that no doors to the hood are needed. Each hood in the laboratory at Sydney is connected by a glazed earthenware drain-pipe with a vertical flue, 20 ft. high, having a lighted gas jet at the bottom to assist the draft. Although the draft is good, fumes of sulphuric acid cannot be drawn o$ unless the doors of the hood are lowered more than half-way. In my opinion, a fan should be used for the purpose of creating the draft, and glazed drain-tile should invariably be used for the flues because no other material possesses the same advantages. I know of a recent instance in which a laboratory containing

Mar 1, 1905

By Richard W. Lodge

Several methods, both wet and dry, for the assay of zinc-box residues from the cyanide process, have been described in recent years, and each of them has been claimed to be superior to all others. In the year 1901, a paper, entitled "Assay of Zincy Precipitates," was published ill the School of Mines Quarterly to the purport that the scorification method for the assay of zinc-box residues was absolutely unreliable. In order to shed light on this matter, the following experiments were undertaken by Messrs. C.B. Hollis and F. D. Kehew, undergraduate students at the Massachusetts Institute of Technology. The zine-box residues used were obtained through the courtesy of Mr. H. R. Batcheller. The samples were very rich and varied greatly in the fineness of their condition. SCORIFICATION-ASSAYS. In the preliminary tests, the charge, which was weighed on a chemical balance, consisted of 0.1 Assay Ton of residues mixed with from 30 to 35 grammes of test-lead and placed in a 3-in. scorifier, over this an additional quantity of test-lead (from 30 to. 35 grammes) was placed for a cover, and borax-glass, varying in quantity from 3 to 15 grammes, was sprinkled over the top of each charge of the various assays for a cover. The charges were scarified in a muffle-furnace heated to the ordinary temperature which is used in scorification; in some cases the door of the muffle was left open, while in others it remained closed. Generally, the charges spit badly, especially in the assays that were made with door of the muffle left open, or in those in which the door was opened too quickly. The results of the preliminary assays showed: 1. That in order to obtain approxi-

Jan 1, 1904

By M. J. Saarivirta

A high-purity copper-zirconium alloy system was imesti-gated. The zirconium content of the alloys studied varied from 0.003 to 0.23 pet. The solid solubility of zirconium in copper and some physical and mechanical properties of the alloys have been determined. By proper heat treatment, Cu-Zr alloy can develop a high electrical conductivity and resistance to softening at temperatures up to 500°C (930°F). This combination of desirable properties makes this alloy superior, to other com-merzcrrl copper base alloys for- use in the electrical conductor field. DEMAND for high conductivity copper alloys that retain their mechanical properties at elevated temperatures is growing rapidly. At present, copper-base alloys such as copper-silver and copper-chromium are used where these characteristics are required. As an example, commutators in electric motors are often made of these alloys. However, the life at elevated temperature of commutators made of copper-silver alloys is much shorter than the life of the same part made of copper-chromium and copper-zirconium alloys. Copper-silver alloys are subject to creep and subsequent failure when the service temperature exceeds several hundred degrees centigrade. Use of copper-chromium alloys has been known for the past several years, but little information is available in the literature concerning the properties of alloys in the copper-zirconium alloy system. Some work had been directed toward determining the solubility of zirconium in copper as well as determining properties of the Cu-Zr alloys. These investigations have revealed the superior high-temperature and electrical conductivity properties of copper-zirconium alloys over copper-chromium alloys. The United States Metals Refining Co., Carteret, N. J. has recently produced OFHC R copper-zirconium alloys for experimentation and evaluation. Because OFHC R copper contains no appreciable oxygen, no harmful oxides are formed and the full benefit of Zr as an alloying addition is obtained. This paper describes the results of this work. It contains room-temperature and some high-temperature data which have been obtained after various processing techniaues. Actual elevated temperature properties are being determined and will be reported in a separate paper. Preliminary results obtained at elevated temperatures suggest that the Cu-Zr alloy is superior to other high conductivity copper-base alloys. WORK PROCEDURE The high-purity oxygen free (OFHC R) copper-zirconium alloys with zirconium content ranging from 0.003 to 0.23 pct were cast into 4-by 4-in. wirebars by both continuous casting and conventional casting methods. Zr was added in the form of a master alloy containing 30 pct Zr and 70 pct Cu. Castings were analyzed for zirconium and nine bars containing various amounts of zirconium were selected for this study. The results of analyses and the sample numbers are given in Table I. Typical analyses of OFHC R copper are also shown. The following properties were studied: A) Solid solubility of zirconium in copper. B) Effect of zirconium on properties of copper. C) Effect of combined working and heat treating on properties of Cu-Zr alloys. The solid solubility of zirconium in copper was determined by metallographic techniques. Specimens for this phase of the investigation were hot rolled at 900oC (1650oF) to 0.250-in. rod. The rolled rods were cut into 2/3-in. long specimens and solution annealed at 950 °C (1740°F), 980°C (1795 °F). and 1020 °C (1870 °F) for 6 hr and quenched in water. In order to find the solid solubility limits at lower temperatures, the homogenized specimens were reheated at various temperatures for 1 hr and quenched. The physical and mechanical properties were determined on 0.250 in. rod, 0.132- and 0.081-in. wires. The wires were cold drawn from the 0.250-in. rods after they were solution annealed at 980 °C (1795°F) and quenched in cold water. Mechanical and electrical properties were determined on cold drawn and

Jan 1, 1961

By G. L. F. Powell

TURNBULL and Cech1 reported undercooling small droplets (approximately 50 mp in diam) of a large number of metals by approximately 0.18 TE (TEoK = the equilibrium freezing point). This was considered to be the undercooling for homogeneous nucleation in

Jan 1, 1968

By Christie A. Callender, Harry M. Dahl

The Hobson uranium deposit is located in Karnes County, Texas, along the prominent south Texas uranium trend. The uranium mineralization occurs in the Deweesville Sandstone of the Whitsett Formation of the Eocene Jackson Group. The host rock is a friable, fine-grained, well-sorted, highly porous and permeable sandstone interpreted to be an ancient beach deposit. The sandstone contains significant volcanic constituents and ranges in composition from arkosic to tuffaceous. Locally, the host sandstone contains hard, dense opal cement. Bentonitic shales underlie and overlie the mineralized sandstone unit. Geometrically, the Hobson uranium-bearing zone resembles an elongated roll front type deposit. Chemical uranium values compared with gamma ray equivalent uranium values indicate that the uranium has been dissolved from the updip side and precipitated on the down- dip side of the roll front. Details of the uranium mineralization were studied using thin section microscopy, autoradiography, x-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) techniques. The uranium mineralization occurs in the pores of the sandstone, as grain coatings and as replacement of sand-size and smaller grains. It is commonly associated with pyrite and other opaque minerals. Other favored hosts for uranium (other than pore openings) appear to be clay aggregates, altered rock and glass fragments, and carbonaceous plant debris. Aggregates of coffinite were identified by XRD and SEM/EDS analyses. Some uranium mineralization also appears to be dispersed and is postulated to be adsorbed on the clay and carbonaceous matter.

Jan 1, 1985

By H. F. Kendall, J. H. Ffolliott

MANY papers and reports have been devoted to the geology and ore deposits of the Ducktown district, Tennessee, especially the complete report by W. H. Emmons and F. B. Laney, published as Professional Paper 139, by the U. S. Geological Survey. The present paper discusses the work of the geological organization of the Tennessee Copper Co., which is based on the field work of the above paper and the consulting work of W. H. Emmons. The Ducktown basin lies in the southeastern corner of Tennessee and extends a short distance into Georgia and North Carolina. All productive mines are contained in an area of 15 sq. mi. in the center of this basin, which is an undulating plateau at an elevation of 1650 to 1800 ft. above sea level. It is surrounded by the relatively high mountains of the southern Appalachian region. The rocks are of early Cambrian age. Deposition of the ores probably took place during the latter part of the Paleozoic era. The ore deposits are rudely tabular to lens-shaped bodies of massive sulfide, varying from a few feet to over 200 ft. in width. In general they all strike northeast and dip southeast at angles from 45° to 70°. Locally, where affected by folding and faulting, the variations in dip may be even greater. The lodes usually are parallel at distances of from one-half to one mile measured normal to the strike. The deposits are a replacement of a fairly continuous bed or a series of disconnected limestone lenses, highly folded and somewhat faulted, which probably represent the same stratigraphic horizon.

Jan 1, 1933

By M. C. Fuerstenau, R. B. Bhappu

The response of beryl to sulfonate flotation was examined. The dependence of flotation recovery on sulfonate concentration, pH, and the absence or presence of various ions is also demonstrated. The response of quartz and feldspar to sulfonate flotation at various values of pH is given to. show the conditions necessary for selective separation. Finally, beryl was successfully concentrated from a natural ore using a technique devised from experimental observations on systems of pure minerals. With the possible exception of quartz, the flotation characteristics of silicate minerals are rather poorly understood. This is due in part to the com- plexity of the mineral systems themselves and in part to an insufficient amount of flotation data. The complexity of the systems arises from the wide range of chemical composition that the silicate minerals can assume. This is reflected in the variability of such physical properties as hardness and cleavage. Although the chemical composition of silicate minerals can vary considerably, a general grouping can be accomplished conveniently on the basis of the assemblage of SiO4 tetrahedra in all the silicates. That is, it has been shown that six basic groups can be obtained, depending on the arrangement of oxygen sharing between adjacent silicon atoms (or substituted aluminum). When all four oxygen atoms are shared, a framework structure such as quartz or feldspar is obtained. When three oxygens are shared, infinite sheets are obtained as in the micas and clays. When two oxygen atoms of the tetrahedra are shared, infinite chains are obtained, such as those in

Jan 1, 1963