Search Documents

By K. J. Miller, R. E. Hucko

The Coal Reparation Division of the Pittsburgh Mining Technology Center conducted an investigation to assess and compare the pyritic sulfur reduction potential of coal-pyrite flotation and high-gradient magnetic separation (HGMS). Tests were run on three coals - an Upper Freeport bed coal, a Lower Kittanning bed coal, and a Pittsburgh bed coal - to establish grade-recovery relationships characteristic of both processes. Representative portions of each coal sample were crushed to two top sizes-nominal - 500 pm (-35 mesh) and nominal - 149 pm (-100 mesh)-and subjected to conventional froth flotation. The froth product was then beneficiated by coal- pyrite flotation or HGMS, to provide a direct technical companion of the two processes. At - 500 pm (- 35 mesh), the size normally employed for coal flotation, both coal-pyrite flotation and HGMS effectively separated pyrite from coal, and the performance of the two processes was essentially the same. At a - 149 pm (- 100 mesh) sire, however, the performance of HGMS exceeded that of coal-pyrite flotation. The separation effected by HGMS were more efficient at - 149 pm (- 100 mesh) than at - 500 pm (- 35 mesh). On the other hand, it was concluded that either the effectiveness of coal-pyrite flotation decreases with diminishing top size or the process has not been optimized to treat material finer than 500 pm (35 mesh).

Jan 1, 1983

By W. A. McCurdy, Joseph W. Leonard, William F. Lawrence

INTRODUCTION Utilization from the Point of View of the Preparation Engineer The primary interest of the coal preparation engineer is in process design, operation, and maintenance to produce an acceptable product that can be sold at the greatest possible profit. Because of emphasis upon these interests, attention to other potential values of coal is sometimes neglected. The intent of this chapter is to alert the preparation engineer to the utilization possibilities of the product as well as the tributary coal flow moving through a modern coal preparation plant. The basis for any unrealized potential derives directly from the coal seam itself. Most coal seams consist of coal bands and benches sandwiched together in layers that differ visually from each other in physical structure and luster. Randomly selected physical and chemical ranges determined from layers of coal in a single seam can easily differ by as much as 30 Hardgrove grindability indices, 0.30 of a specific gravity point, 20 percentage points of ash, 6 percentage points of dry volatile matter, and 10 percentage points of total su1fur.l Similar wide variations exist for calorific value, seam moisture content, and, undoubtedly, for any other conceivable coal test parameter that might be used for comparative purposes. These observations all point to the long-established fact that coal is not homogeneous, as conventional analytical methods might tend to indicate, but is instead a highly heterogeneous substance.

Jan 1, 1979

There have been no major field developments during 1935. Operations have proceeded normally on the company's three producing fields, Masjid-i-Sulaiman, Haft Kel and Naft-i-Shah. The refinery at Kermanshah was commissioned in September, 1935, with a rated throughput capacity of 75,000 tons a year of topped crude to meet local requirements. Crude production from the Masjid-i-Sulaiman and Haft Kel fields is tabulated below: Masjid-i-Sulaiman Field.—The flowing lives of wells have been extended by (I) a process of acid treatment, thereby reducing the bottom-hole pressure differentials, and (2) by reducing the back-pressure. Optimum producing conditions for individual wells have been determined as a result of an experimental study of the amount of available energy in the reservoir crude and of energy losses in flowing wells. The return of surplus products to the reservoir has continued to be a satisfactory economic operation and the crude throughput capacity of the topping plant has been increased. The viscosity of residue returned to the reservoir is reduced before injection by regassing at 35 lb. per sq. in. absorption pressure with surplus gas. The pressure in the gas dome is falling at the low rate of one pound per annum. Haft Kel Field.—The delimitation of the main structure has proceeded; the oil-bearing area so far proved being about 50 square miles.

Jan 1, 1936

There have been no major field developments during 1935. Operations have proceeded normally on the company's three producing fields, Masjid-i-Sulaiman, Haft Kel and Naft-i-Shah. The refinery at Kermanshah was commissioned in September, 1935, with a rated throughput capacity of 75,000 tons a year of topped crude to meet local requirements. Crude production from the Masjid-i-Sulaiman and Haft Kel fields is tabulated below: Masjid-i-Sulaiman Field.—The flowing lives of wells have been extended by (I) a process of acid treatment, thereby reducing the bottom-hole pressure differentials, and (2) by reducing the back-pressure. Optimum producing conditions for individual wells have been determined as a result of an experimental study of the amount of available energy in the reservoir crude and of energy losses in flowing wells. The return of surplus products to the reservoir has continued to be a satisfactory economic operation and the crude throughput capacity of the topping plant has been increased. The viscosity of residue returned to the reservoir is reduced before injection by regassing at 35 lb. per sq. in. absorption pressure with surplus gas. The pressure in the gas dome is falling at the low rate of one pound per annum. Haft Kel Field.—The delimitation of the main structure has proceeded; the oil-bearing area so far proved being about 50 square miles.

Jan 1, 1936

By Elmer R. Kaiser

G. A. Vissac (Consulting Engineer, Vancouver, B. C.) —Some of the data presented in this paper, in connection with cost studies of washed coals, should be clarified and qualified. Washing a raw coal down to a low ash content may mean higher losses in refuse, but the cost of the operation may be more than compensated by the increased value of the resultant product. However, careful engineering and accurate machinery are required to insure maximum profits. Washing at a low gravity separation demands a very accurate automatic process, chiefly when the small sizes of coal are being handled. Coal consumers today are buying mostly on a Btu basis, cognizant of the fact that low ash contents result in lower installation costs and in savings in handling and transportation charges. The attached Table X gives the actual balance sheets of the various cleaning operations corresponding to various ash contents for the two coals presented in the paper, using the old technique of a two-products separation. or the new technique, now commonly used in Europe, of a three-way separation made possible by new methods and new equipment. Savings in capital costs, handling, and transportation have been calculated on the basis of a delivered cost f.O.b. plant of $10.00 per ton of coal at 16.5 pct ash (actual 1953 average price reported by Consolidated Edison, N. Y.), and of $3.50 at the mine also for 16.5 pct ash coal. In both cases this corresponds to values of 126 and 4.26 per 1 pct of combustible and per ton, respectively, on delivered and on at the mine prices. As an example, the middle western coal at 16.5 pct ash, raw, washed down to 4 pct ash in a two-way process will give 53.75 pct of clean coal at 4 pct ash and 46.25 pct of refuse at 31 pct ash. The value of the losses will be 0.4625x(100—31)x0.042 = $1.34. Add the cost of washing, capital, and operation, which is $0.35. The total cost will then be $1.69. But with a three-ways separation we will have 53.75 pct of first-grade coal at 4 pct ash, 37.25 pct second-

Jan 1, 1955

By Marsh S. Watson, Robert A. Howard

An electrolytic model study has been made of the relative productivity of perforated casing. The results show that the relative productivity is roughly one-half to two-thirds of that predicted from point-sink calculations. This discrepancy can he satisfactorily explained on the basis of casing interference. The relative productivity was found to he insensitive to spatial arrangement of the perforations. INTRODUCTION The relative productivity of wells with perforated casing has been treated mathematically by Muskat.' In his treatment the perforations are represented by small spheres, thus enabling him to approximate the flow by that to point sinks. By neglecting interference between the flow into the various spheres representing the perforations, one may deduce the approximate formula Qu 1/rp - 1/rw • (1) I + b/2n _________ 2n In re/rw Where Q is the flow rate into spherical sinks located in the median plane of the sand laver Qo is the open hole flow rate (uncased hole of radius rw) b is the thickness of sand layer under consideration (always one foot in this paper) n is the number of spherical sinks in the sand layer rp is the radius of a spherical sink rw is the well radius re is the drainage radius of the well. Fig. 1 is a comparison of values calculated from equation (1) with Mus-kat's values. It will be observed that the approximate values are in error by less than 21/2 per cent. The disturbing effect of the casing on the flow line; is not explicitly taken into account by Muskat, but he reasons that interference between the flow pat- terns from the various point sinks will result in a negligible flow in the region within the well radius, and that no appreciable error will result from not explicitly excluding flow from this region. This line of reasoning is open to question, however, as the flow impedance, in the immediate vicinity of the well, of a hemispherical cavity in contact with an opening in the casing is twice that of a spherical sink in a continuous sand layer. There will be a difference, moveover, between the flow into a hemispherical cavity and that into a circular hole in the casing. .This latter difference can best be appreciated by comparing the flow from a semi-infinite medium into a hemispherical cavity at the edge of the medium with the flow out of a circular opening of the same radius as the hemisphere and which is also on the edge of the medium. In this case2 ------= —2, showing that the difference in flow rates into differently shaped cavities is quite appreciable. It was the purpose of the investigation reported here to determine to what extent flow into circular perforations in casing departs from the values calculated by Muskat. For this purpose an electrolytic model was used.

Jan 1, 1950

By Kenneth Cottingham

THE area described herein is situated on what is known as the Arches Fork anticline in Roane and Calhoun Counties, W. Va. When the area was first mapped, it was felt that well records would give a more intimate idea of conditions, both structural and lithologic, than could be expected from surface horizons. The surface formations are chiefly members of the Monongahela series, though northward the hilltop outcrops are those of the Dunkard. Neither series offers a key horizon sufficiently definite to be satisfactory, although the structure as determined from well records was later checked against two of the more persistent surface sandstones. In mapping the subsurface structure, the top of the Big Lime (Greenbrier) was employed as the key horizon. The average depth to the top of the Big Lime varies from 1600 to 2000 ft. (487 to 609 m.), while the average thickness as indicated by well records is 113 ft. (34 m.). The oil-producing formation is the Big Injun, lying just below the Big Lime. In two instances, well records show the Lime and Injun separated by a few feet of "break." The Big Injun is recorded as having a variable thickness. Seven logs report it as missing and one gives it the maximum thickness of 105 ft. (32 m.), while the entire average for thickness is 19 ft. (6 m.).

Jan 1, 1922

By L. C. Graton

[CONTENTS PAGE INTRODUCTION AND ACKNOWLEDGMENTS. By George M. Fowler2 Question 1-Is Structural Deformation of Some Character Always Necessary for the Migration of Mineralizing Solutions, Especially in Limestone or Other Dense Rock? DISCUSSION by: A. M. Bateman 10 S. F. Kelly 15 C. H. Behre, Jr 8, 13 G. B. Langford 13 T. M. Broderick11 H. E. McKinstry6 R. H. Clarke 13 D. H. McLaughlin8 J. D. Forrester for M. H. Gidel . . . 4 W. H. Newhouse13 G. M. Fowler 2, 6, 11 R. H. Sales 6 L. C. Graton 11 Edward Sampson 12 R. D. Hoffman 10 J. S. Stevenson 7 I. B. Joralemon11 L. B. Wright 2 Question 2-What Are Some of the Chemical and Physical Characteristics in Certain Beds within a Limestone Formation that Determine Their Favorable or Unfavorable Aspects as Reservoirs for Ore and Other Introduced Minerals? DISCUSSION by: G. W. Bain 17G. M. Fowler 21 C. H. Behre, Jr21L. C. Graton18 J. S. Brown 16G. F. Loughlin18 E. L. Bruce 19R. H. Sales 19 R. H. Clarke 20A. K. Snelgrove 20 Question 3-Are There Any Criteria by Which One Can Determine When Mining Operations Have Reached the Roots of an Ore Deposit? DISCUSSION by: J. M. Boutwell29G. B. Langford 29 T. M. Broderick28G. F. Loughlin25 E. Y. Dougherty27R. H. Sales 24 G. M. Fowler 22F. A. Thomson 26 I. B. Joralemon 22Edward Wisser 30 General S. F. Kelly35 References36

Jan 1, 1940

By C. Perez-Rosales

A statistical method for determining simultaneously some of the basic geometrical characteristics of porous media such as porsity, specific surface* mean pore width, mean grain thickness and absolute permeability is presented. The proposed method is characterized by its simplicity and the minimum amount of laboratory equipment that it requires. The experimental procedure used to evaluate the various geometrical characteristics is based 'pan the 'surface analysis Of a a In view of this fact the app1icability Of the method is limited to homogeneous and isotropic materials. INTRODUCTION The behavior of a fluid flowing through a porous medium depends, among other things, upon the internal geometry of the medium; hence the importance of developing efficient methods to determine the geometrical properties of porous materials. This paper describes a statistical method to determine simultaneously some of the basic geometrical properties of porous materials such as porosity, specific surface, mean pore width, mean grain thickness and absolute permeability. The mathematical formulation has been developed that the data required to calculate the various geometrical characteristics of a sample can be easily measured by analyzing a section of the sample with an evenly spaced grid. THEORY A simple way of obtaining information about the internal geometry of a porous material is to throw a point at random over a cross-section of a sample. l-Through this procedure the porosity can be detemined.l,2 By considering that the material is homogeneous and isotropic, and that the point is dropped many times, the porosity 4 is given by where N is the total number of times the point is thrown and n is he number of times the point falls within pore areas. Another simple manner of analyzing the structural characteristics of a porous material is to superimpose an arbitrarily long line on a cross-section so that its length is evenly distributed over the surface area. Through this procedure the porosity can also be determined. If L is the total length of the line, and 1 is the sum of the lengths of the line segments within void spaces, the porosity is given by 4 = —.1.............. (2) The advantage of this type of analysis is that geometrical characteristics other than porosity can be obtained. Thus, if c represents the number of intersections between the line and the perimeter of pores, it can be shown3 that the specific surface, defined as he surface area of pores per unit bulk volume, is given by To give a proper description of the internal geometry of a porous medium, it is necessary to define quantities that characterize the notions of pore size and grain size. Unfortunately, because of the complexity of porous materials, it is difficult to give exact geometrical definitions of what is meant by the ConCePtS of "poresl' and "grains", especially when dealing with consolidated materials. Never theless, one often talks about the "size of pores" and the "size of grains" without defining accurately the terms. A possible solution to this problem follows. Assume that an arbitrarily long line is placed on a section of a sample so that the line is evenly distributed over the surface area (see Fig. 1). 1n a system like this, each line segment within a void space will be, by definition, the pore width in a given location and direction. Consequently, if the

Jan 1, 1970

By AIME AIME

COAL preparation will be the main topic discussed at the first fall meeting of the Coal Division at Pittsburgh, Sept. 11, 12 and 13, though valuation, mergers, safety, stream pollution and other topics will not' be neglected. It is particularly appropriate that the great changes taking place in preparing coal for the market should be discussed at length where in the plants of the Pittsburgh Coal Co. and others the opportunity is afforded to see on a large scale just what is being accomplished. In wartime, the United States broke all records in coal production, but, as the late Franklin K. Lane pointed out, every fifth car shipped consisted of dirt. Obviously that constituted a big bur- den on industry and, in the remaking of the business which is now taking place both in the anthracite and bituminous fields, clean coal has properly enough be- come a watchward. Central coal-cleaning plants are being erected as a part answer to the puzzled inquiry of those familiar with metal mining as to why miners of coal have so long been content with what are relatively small units of production. Gradually big collieries comparable in tonnage output to the biggest copper mines are being built, and excellent examples are to be seen near Pittsburgh. Even the age-long tradition of the coal operator in favor of the single shift is

Jan 1, 1930

By E. V. d’Invilliers

The position of these magnetic ore-mines, with reference to the county-seat, is shown in Fig. 1. They are situated on the south margin of the Great Valley, five miles south of Lebanon, and about midway between Reading on the Schuylkill River and Harrisburg on the Susquehanna River, in three prominent, contiguous hills, standing in front of the Mesozoic red shale arid sandstone hill country of northern Lancaster and southern Lebanon counties, and overlooking the great limestone plain to the north. The three hills, named respectively Big, Middle, and Grassy Hills, and separated from each other by two branches of Furnace Creek, range in a nearly east and west direction for a distance of about one mile. Their summits are respectively 870, 715, and 700 feet above tide. The railroad line opposite the base of Middle Hill is 575 feet above tide at Cornwall and 471 feet at Lebauon. These features are all distinctly illustrated in the contour-line map accompanying this paper, but are made still more clear in the relief. map, Fig. 2, comprising, as it does, about six square miles of territory contiguous to the ore-mines. This is a photographic plate of a model made by Mr. A. E. Lehman, from surveys of my own and Mr. W. F. Shunk. The model was built in layers of cardboard, each layer representing one 10-foot contour-carve line. The scale was the same as the original map, 400 feet= 1 inch, without any vertical exaggeration. The lowest contour-line is 530 feet above ocean level; the highest, 1075 feet. The center of the model was made the focusing-point of the view, which was taken—according to scale—51/2 miles north from and 24 miles above the focusing-point, looking southward. When first mined in the last century these hills exhibited smoothlyrounded surfaces, composed of soft weathered ore of great parity, beneath which lay the great mass of hard ore, constituting the whole

Jan 1, 1886

By W. G. Matteson

The Gulf Coastal plain of the southern United States is that area bordering for a large part, the Gulf of Mexico and extending inland and northward to the main interior highland region. It is more or less V-shaped and includes the States of Florida, extreme southern Alabama, all .of Mississippi and Louisiana, the eastern and southern half of Arkansas, and the eastern, southeastern, and southern portions of Texas. While the contents of this paper apply to. the Gulf Coastal plain in general, they are intended to refer more specifically to that portion of the plain included between the 90th and 97th meridians, and the 29th and 33d parallels, an area that may be described geographically as comprising western Mississippi, all of Louisiana, part of eastern and all of south-eastern Texas. It is within this area that numerous and prolific oil pools have been developed during the last 17 years.

Jan 2, 1918

By E. Ray Webb

A interest to geologists and to mining and petroleum engineers is a laboratory method for determining the dip and strike of sub- surface structures, as well as the direction of fault planes traversing them. The information is derived by making use of the magnetic properties of borehole cores which must show visible representations of bedding or fault planes. Complete knowledge of these factors aids greatly in the successful exploitation of both ore and petroleum deposits.

Jan 1, 1940

By W. O. Crosby

INTRODUCTION. THE crystalline belt of the Atlantic Seaboard, south of New York, attains its maximum breadth of 220 miles on the northern border of North Carolina; and in this State it is most widely characterized by the occurrence of gold in workable deposits. Half a dozen auriferous belts have been recognized by Nitze and Hanna.1 These are, in the main, coincident in position and trend with the NE.-SW. zones of metamorphic slates and schists, which, more than any other feature, give character to the geological map of North Carolina. The central gold-belts, accompanying the main zone of slates and associated igneous rocks, are much the more important and persistent, and may be regarded as continuous northward across Virginia and southward into South Carolina. Tile eastern belt, on the other band, is the shortest and, economically, one of the least important. Its extreme length does not exceed 25 miles, the narrow band of slaty rocks to which it belongs passing, both NE. and SW., beneath the coastal-plain formations. But, although limited in area and production, this belt is, perhaps, comparable with the central belts or any part of the sea-board crystallines in the variety of conditions under which the gold occurs. It lies chiefly in the NE. part of Franklin county and the NW. part of Nash county, on the watershed of Fishing creek and other tributaries of Tar river. The elevation is between 400 and 500 ft. ; and the Tertiary peneplain has here an exceptionally perfect development, the reliefs separating the slightly incised stream-courses consisting of broad, flat-topped peneplain remnants, bounded by gentle lateral slopes.

Mar 1, 1908

By J. E. Hilliard

Isobaric sections of the eutectoid region of the iron-carbon phase diagram have been exgerimentally determined at 35, 50, and 65 kb. The phase boundaries were located by metallographic analysis of specimens quenched after equilibriatwn at known temperatures and pressures. With increasing pres -sure a pronounced decrease in the solubility of FesC in austenite was observed together with a depression of the eutectoid temperature. These two effects resulted in a shift of the eutectoid composition toward a lower carbon content; at 65 kb the eutectoid was at less than 0.2 wt pct C. These results are in qualitative agreement with thermodynamic calculations. It has also been shown by calculations that Fe3C in contact with saturated austenite will be stable with respect to both graphite and diamond formation at all pressures above -3.5 kb. 1 HE investigation described in this article was part of a more general study of the effect of high pressure on transformations in Fe-C alloys. Thermodynamic calculations and exploratory runs made in 1959 at the start of the program indicated an appreciable change with pressure in the phase equilibria of Fe-C alloys. However, the calculations were not considered reliable enought to provide the quantitative information required for the interpretation of the effect of pressure on the kinetics of transformations. An experimental investigation was therefore made to determine a series of isobaric sections of the eutectoid region of the phase diagram at pressures up to 65 kb. EXPERIMENTAL PROCEDURE Materials. Seven alloys with analyzed carbon contents of 0.10, 0.20, 0.38, 0.60, 0.77, 0.93, and 1.20 wt pct C were prepared from Ferrovac" iron and high-purity graphite induction melted in magnesia crucibles under argon. The ingots were hot worked and swaged down to 0.19-in.-diam rod which was then centerless ground to a final diameter of 0.125 in. Samples for chemical and spectrographic analyses were taken from each end of the rods. The prin- cipal impurities were found to be Ni, Al, Co, and Si which were present in amounts up to 0.03, 0.02, 0.01, and 0.01 wt pct, respectively. Specimens were prepared by slicing the ground rods into pills 0.06-in. thick which were silver plated to reduce decarburization during the equilibration. Silver was chosen for this purpose because of its very low solubility for carbon and its mutual immisicibility with iron. High-Pressure Apparatus. The high-pressure runs were carried out in the "Belt" apparatus.' As shown in Fig. 1, this consisted of a cylindrical cell compressed between two Carboloy punches loaded by a uniaxle press. Radial support to the cell was given by the "belt" which was a Carboloy die heavily prestressed by a series of steel binding rings. Laminated gaskets of lava and metal separated the punches from the inner surface of the "belt". A cross-section of the high-pressure cell is shown in Fig. 2. Two specimen pills were located inside a resistance heater of 0.20-in.-diam Nichrome tubing. The ends of the tube were sealed with alumina and lava pills tamped in place after the

Jan 1, 1963

By Earl F. Hanson

Fires in heavily timbered mines are disastrous, involving danger to both life and property. Some mines have been completely ruined or so heavily damaged that reopening them would not pay. Though few mines are entirely free from danger of fire, the risk is minimized by proper care and good design of plant. The Tintic Standard mine is at Dividend, Utah, in the famous Tintic mining district, about 60 miles south of Salt Lake City. The development of the mine was begun in 1907 by the late Mr. E. J. Raddatz and his associates. From the beginning, the work was hampered by high rock temperatures and the presence of high concentrations of rock gases such as carbon dioxide and nitrogen. Development work was carried on with great perseverance for nine years, and resulted in the discovery of ore in 1916. The total production of the Tintic Standard mine to Jan. 1, 1936, amounted to 1,664,388 tons of ore, having a gross value of $61,996,719. General Layout of the Mine The No. 2 shaft, which is the main working shaft of the Tintic Standard, is within the main orebody and is connected with the five other shafts. Their respective positions with respect to the No. 2 shaft are as follows: North Lily, 2770 ft. northwest with drift connections on the 700 and 900-ft. levels; No. 3 shaft, 670 ft. east connected through the 700-ft. level; Eureka Standard, 4550 ft. south, connected on the 900-ft. level; No. 1 shaft, 1470 ft. southwest, with connecting drifts on the 900 and 1250-ft. levels; Eureka Lilly, 2000 ft. southwest, with connecting drift and raise through the 1250-ft. level. The Tintic Standard orebody consists essentially of one continuous oreshoot extending from the 600-ft. level to the 1450-ft. level, with a cross-sectional area of approximately 70,000 sq. ft. at both top and bottom, reaching a maximum area of 215,000 sq. ft. between the 1100

Jan 1, 1937

By J. C. METCALF

MORE than 80 per cent. of the iron produced in the United States and over 30 per cent. of the world's annual production is obtained in the Lake Superior district. Though iron ore was discovered on the Marquette range in 1844, the poor transportation facilities retarded the development of this region for many years. The structure of the Lake Superior basin is essentially an east-west synclinorium with steep dips on the south side of the lake and considerably flatter ones on the north and west. The Upper Huronian series, which -is the iron-bearing one of the formation, on the south side of the lake dips north from 55' to 80°, and on the north side dips south from 8" to 200. The series has been subjected to local folding and faulting, which have influenced the development of the mining systems used.

Jan 1, 1921

By W. L. Finlay

Size effects in quenching steel are particularly prominent and well recognized because of the existence of a critical cooling rate separating nuclea-tion and growth transformations, as exemplified by the formation of pearl-ite, from the shear type of transformation characterizing the martensite reaction. The absence of a similar, sharply demarcating cooling rate is characteristic of precipitation hardening systems and size effects in these are correspondingly less prominent. This paper is concerned with a size effect in high-purity, precipitation-hardenable alloys which appears not to have been recognized previously. This effect is believed to result from the thermal fluctuations which inevitably occur in quenching a specimen of finite size into a cooling liquid rather than from the existence of a critical cooling rate. QUENCHING "ANOMALIES" The precipitation hardening literature contains many references to so-called anomalous quenching and aging results. By "anomalous", investigators usually meant that their alloys did not consistently harden on aging after quenching according to some anticipated pnttern: not infrequently virtually no age hardening occurred with compositions known to be precipitation-hardenable. Perhaps the most prominent series of anomalies was reported over a 15-year period by Gayler and coworkers on aluminum-copper.l,2,3,4 Working with silver-rich copper alloy, Cohen5 secured some very interesting Rockwell F hardness changes of from 1-5 Rockwell points between the first peak and valley. Fink and Smith borrowed one of Cohen's specimens and, following his heat treatment and quenching practice to the letter, secured6 very different results in which only one peak was obtained and in which the hardness level at the aging lime of Cohen's first peak was 20 Rockwell F points higher. Fink and Van Horn7 encountered serious deviations in age-hardening high purity aluminum-zinc alloys. They stated that "the discrepancies were larger than might be expected from possible experimental errors in the Brinell readings." Geisler, Barrett and Mehl8 likewise encountered anomalous hardening results in aluminum-silver alloys, securing quite different age-hardening curves from two identical specimens. They stated that "the treatments of these samples had been the same, so that the different behaviors could be attributed only to accidental variations in the quenching practice."

Jan 1, 1950

By W. H. Emmons

THIS paper is the third of a series treating of the relations of ores of the metals to igneous rocks. The first1 outlined the general problem; the second2 proposed a classification of lode ores, and showed how the distribution of the deposits is in a certain measure controlled by the contour of the roof of the parent batholith. A number of mining districts were discussed, the examples being selected chiefly from group 2 of the classification. The proposed classification of lode deposits, briefly stated, is as follows: 1. Cryptobatholithic: near hidden batholiths which have not yet been exhumed by erosion. 2. Acrobatholithic: in and near cupolas or domes of batholiths-the high points of larger underlying masses. 3. Epibatholithic: on batholiths, near their rims, but below eroded cupolas, or below the highest points of the roofs. 4. Embatholithic: among closely-spaced outcrops which probably are parts of a single batholith. The outcrops of invaded rocks predominate. 5. Endobatholithic: in and near roof pendants of large batholiths. The invading rocks predominate. 6. Hypobatholithic: in deeply-eroded batholiths, where even roof pendants, have been -eroded. Deposits of certain metals on the roofs of the batholiths are much more numerous in some positions than deposits of other metals, and the horizontal zonal arrangements of lodes of different metals are shown characteristically only in certain groups. In a large measure, also, the character of the fracturing and metallization is determined by, the-position on the roof, of the batholith.

Jan 1, 1927

By Gustav Egloff

AN unexpected and unprecedented demand for its products now challenges the petroleum industry. Between 1939 wand 1946, domestic oil demand increased nearly 45 per cent and in the first half of 1947 it was 10 per cent higher than in 1946. In 1939 the United States produced 1,264,962. 000 bbl of crude oil and indications are that about 1,860,000,000 bbl will be produced in 1947, a 47 per cent increase. Runs to stills are more than keeping pace with production. The crude capacity of 365 operating refineries is rated as 5,400.000 bbl daily and almost 100 per cent of this capacity was running crude oil in August 1947. The oil industry is cognizant of our need for a greater volume of petroleum products and is expending the huge stun of four billion dollars on exploration. production. transportation, refining. and marketing of petroleum. Of this amount about half will be spent on exploration and production. a billion on refining. and another billion on transportation and marketing facilities.

Jan 1, 1947