Search Documents

The Library of the above-named Societies is open from 9 A.M. to 10 P.M., except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information' will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 2, 1918

By W. M. Aubrey

Lying approximately 110 miles east of Toronto, Canada, the Marmora mine produces iron ore with a content of about 40 pct Fe, primarily in the form of magnetite. Operated by the Marmoraton Mining Co., a subsidiary of Bethlehem Steel Co., the orebody is mined by open pit methods. The ore from the pit is crushed, cobbed, ground to -100 mesh, magnetically concentrated to 67 pct iron, and then pelletized in shaft furnaces. The pellets are normally shipped by rail throughout the year from Marmora to Picton on Lake Ontario where they are unloaded and stored. Subsequently, during the navigation season, the pellets are shipped to Bethlehem Steel's Lackawanna plant in Buffalo, New York, for use in the blast furnace. At Marmora, the pellet plant demand and the concentrator output are not usually equal. To counter this problem, surge capacity in the form of storage pits in combination with a 30-ft diam thick¬ener has been provided between the concentrator and the pellet plant. Two sets of controls have been installed on this thickener, one controlling the…

Jan 9, 1960

By Charles M. Haas

WHEN minable ore has been located, the problem of mining is synonymous with the problem of movement --movement of men and equipment to mine the ore, and movement of the ore from the earth to the mills. In slusher drifts and shafts, on shovels and dragline excavators, on churn drills and bulldozers, wire rope is essential to the transportation of men, ore, overburden, and equipment. Although a casual glance creates the impression that all wire ropes are alike, there are crucial differences between ropes. Strand diameter, number of strands, weave, core, and resistance to corrosion all decide the type of job a wire rope can do, and where and how long it can do that job. These factors are, of course, the responsibility of the rope manufacturer. Beyond this, he can extend his function into the mine itself by advising users on the use, care, and maintenance of these sinews of the mining industry. This article, then, covers both the manufacturing and end-use aspects of wire ropes.

Jan 9, 1951

THE Pacific Northwest's joint meeting of the Industrial Minerals and Metals Branch in Spokane, Wash., drew 260 members, 72 students, and 30 ladies. Theme of the meeting was to acquaint men in the industry with students and younger men. The special appeal to the students was coupled with an attempt to attract young technical men from the companies located in the northwestern area. The activities of the meeting were available without charge to students. Contributions were made by the industries in the area to assist student attendance. Following the special student and faculty trip to the Trentwood rolling mills and research laboratory on Friday afternoon everyone enjoyed a complimentary dinner. A. Y. Bethune of the Sullivan Mining Co., spoke to the group on the operations of Kellogg, Idaho electrolytic zinc plant. The Industrial Minerals Div. session was opened on Saturday morning by R. G. Vervaeke, Conference Chairman who introduced A. O. Bartell of the Raw Materials Survey, Portland, Ore. Mr. Bartell in turn introduced C. W. Sweetwood who discussed Open-Pit Phosphate Mining.

Jan 1, 1952

Some years ago it was my good fortune to inspect some coal properties in Germany, and the most striking impression I received on my trip was that in that country every one in the coal industry, miners and operators, was proud of the fact-not apologetic about it-and that industrially coal was looked upon as a King. The explanation, of course, was that at least 90 per cent of the entire mineral value produced in Germany was from coal, and that it was the very foundation of the nation's industrial life. The feeling was so different from that existing in the United States among those engaged in producing coal that it made a profound impression on me, and many times since then I have speculated about the reasons for the difference in opinion in the two countries. Here, of course, our units are much smaller and more numerous, there is not so large a proportion of technically trained men, and we have the American trait of depreciating the things we do at home; but among those not actively

Jan 1, 1939

By AIME AIME

In taking account of stock, on the occasion of the recent removal of the office of the Institute, it was found that pamphlet copies of the papers named in the list given below were on hand, in excess of the average number deemed adequate for future casual demand. Special reduced rates will be made for these surplus copies to members applying promptly. "First come; first Served." Author. Title. Ref. No. ASHBURNER, C. A. " Petroleum and Natural Gas in New York State." 273 MARTENS, A. "The Microstructure of Ingot¬ Iron and Cast Ingots." 626

Jan 1, 1907

JamEs F. Kemp, New York, N. Y.:—Mr. Hewett's paper is one of exceptional interest, because it not only adds an important contribution regarding one of the rarer, valuable elements, but also because it introduces compounds hitherto unknown and in associations no less novel. While we have occasionally discovered and recorded asphaltite in metalliferous deposits, for example in the Joplin and Granby districts, we have not seen a metallic ore in a deposit eesentially asphaltite. The source and method of introduction afford a subject well worth serious reflection.

Jan 1, 1910

By Chris Mills

The role of gravity separation in the mineral industry is briefly considered in perspective. The mineralogical and laboratory approaches to gravity process design are examined with emphasis on process technology selection. The equipment available for small scale and pilot test-work is discussed, particularly in regard to scale-up and the acquisition of reliable, accurate data. Transposition of performance data from pilot scale to plant scale is explained. The available types of full scale gravity separation equipment are discussed with emphasis on large high-capacity units. Plant layout and selection of ancillary equipment are considered.

Jan 1, 1978

By S. S. Hsieh

Important carboxylic acid components of tall oils were tested individually as phosphate flotation reagents. These included C18 unsaturated fatty acids and C10 to C18 saturated fatty acids and resin acids. These experiments were conducted to evaluate such factors as the degree of unsaturation, hydro-carbon chain length, isomeric form, side-group modification, and cyclic structure. The effects of mineralogical characteristics on flotation response also were considered. Results of this systematic evaluation provide guidelines for selecting efficient substitute reagents and fundamental data for further research on improved flotation technology.

Jan 1, 1983

By T. H. Chin, R. W. Bartlett

A simple on-stream particle-size analysis method is presented that leads to a bulk-property single-channel device; although the concept can be extended to multi-channel sizing information. The method is based on continuously measuring and comparing the percent solids in the sample stream and in an internal-reference stream containing only undersize particles. A semipermeable hydraulic system is used such that the particle mass concentration in the internal stream can vary, and is always proportional to the undersize particle mass concentration in the sample stream.

Jan 1, 1975

By K. Hanumantha Rao, T. C. Rao, M. Vanangamudi

The effects of important variables such as pulp density, feed size, furnace oil dosage, degree of agitation, and time of agglomeration on the yield and ash content of the agglomerates obtained from the oil agglomeration of coal fines have been studied in a laboratory batch agglomeration cell. Optimum conditions for maximum yield and throughput have been discussed. The furnace oil dosage and pulp density were found to have more influence on the yield and grade of the agglomerates than the degree of agitation and feed size in the ranges studied.

Jan 1, 1983

By T. S. Fuller

THE experiments described in this paper constitute the preliminary work of an investigation outlined to determine the combined effects of steam and temperature on the endurance properties of certain steels. Essentially of a fundamental nature, it was found necessary, in order to make the investigation comprehensive, to test materials treated to give a wide range of properties. The work reported deals chiefly with nickel steel with one series of tests including nitriding steel. Such a study involves numerous variables, and requires an endurance-testing machine of rather special design.

Jan 1, 1930

By Alfred E. Hunt

Tars paper is suggested by the appointment on the part of the American Societies of Mechanical and of Civil Engineers of committees upon the subjects of " Standard Tests and Methods of Testing," and " Uniform Methods of Tests of Material used in Metallic Structures," respectively, and by a study of the report of one of these committees, and other papers. Moreover, the writer has had frequent occasion to hear the complahts of tnanufacturers who furnish structural material subject to specifications, that in the tests prescribed, the number of tests required, and the methods of making

Jan 1, 1892

By F. J. Hurst

The rapid expansion of the phosphate fertilizer industry in conjunction with the projected shortage and spiraling price increase of uranium has greatly renewed interest in wet- process phosphoric acid as a significant source of uranium. Two attractive solvent extraction processes for recovering uranium from the acid have recently been developed and tested through bench-scale at Oak Ridge National Laboratory. One of the processes has been successfully tested on a pilot-plant scale at phosphate plants; the second process, which offers several potential advantages, still needs additional testing. The merits of each process are discussed.

Jan 1, 1978

By John A. Wolfe, James A. Niederjohn

Applications of mathematical statistics to the field of exploration are still relatively new. There are two primary reasons why little has been published in this field. First, if one discovers an effective technique for exploration, he does not like to disclose it. Second, the geologist needs to work closely with a mathematical statistician, and the communications barrier between the disciplines is formidable. The authors, one a geologist and the other a statistician, were interested in the economic benefit which appeared to be possible in the inter-disciplinary area they call "geostatistics."

Jan 11, 1962

By F. Rosenblum

An on-stream particle size analyzer (PSA) based on the sedimentation principle has been developed to the commercial prototype stage and tested at a concentrator. The current instrument gives a direct reading of the weight % finer than any two sizes, although the capability exists for providing a complete size distribution through the sieve and sub-sieve range. The readings obtained at intervals of about 10 minutes are derived from 0.5-L samples of slurry cut from the monitored stream. The accuracy of the PSA meets the requirements of process control.

Jan 1, 1984

By F. G. Miller, J. M. Podgursky

Laboratory and pilot plant work on tabling of 14-mesh X 0 hydrocyclone under flow are summarized. Included are: operating principles of hydrocyclones and tables; performance of these two devices, separately as well as in combination; comparison of the combination hydrocyclone-table system with other fine-coal processing systems; and application of the hydrocyclone-table system in fine-coal circuits. The data show that the table actually compensates for the shortcomings of hydrocyclone and makes a combination table-hydrocyclone system attractive, particularly in those cases where fine pyrite is one of the major contaminants.

Jan 1, 1973

Accurate modeling of the semivariogram is an extremely important step in the geostatistical analysis of mineral deposits. Automatic fitting of a mathematical model is often possible but not necessarily desirable. Significant geologic and statistical information must be taken into account in the fitting process, which is not always available to the computer. Manual model fitting is, on the other hand, extremely time consuming. Interactive graphics are best suited to optimize the process. Many interactive methods are described, which are adapted to modeling semivariogram in one-, two-, or three- dimensional environments.

Jan 1, 1985

By Howland Bancroft

The writer has observed that some confusion is experienced by many mining engineers in making vertical sections of ore deposits in mining properties which they have examined. Having much examination work calling for the correct interpretation of vein structure and the subsequent platting of the same on sections, it has occurred to the writer that the accompanying diagram may be of use to others who at times may be called upon to prepare numerous sections. For example, a great mass of data on strike and dip of ore bodies is collected underground in separate

Jan 1, 1915

By Jack Parker, Gonzalo Barrientos

The most realistic mine pillar design is based on observations and measurements in situ. Low-cost reliable instrumentation has made this approach possible. At the White Pine mine, with its thousands of pillars of all shapes and sizes under all kinds of loading conditions, practical pillar design criteria have been developed. The pressure arch theory is explained and work in two test panels o f the mine is described. The pressure arch mechanism, which relies on lateral stress for support, can be applied to puzzling roof and pillar conditions in other mines.

Jan 1, 1975