Search Documents

By Friedrich Wellmer

INTRODUCTION The Ramsbeck Pb/Zn Mine is located in the northern Sauerland area of West Germany, 150 km N of Frankfurt and 120 km E of Cologne. This is a vein deposit which has been worked from the middle of the 19th century to 1974. About 15 million tons of ore were mined and milled. The ore district contains several vein deposits and is roughly 14 km in length and 4 to 5 km in width. The host rocks are strata of Lower Middle Devonian age. The strata strike 60° to 70° NE and where overturned have a dip steeper than the veins (Fig. 1). The galena-sphalerite mineralization is in quartz veins, which are mineralized where they cut the "Main Ramsbeck Quartzite" horizon, a very competent host rock. Vein structures strike at 65º to 75º, dip about 20° to 25º SE and cut the quartzite at approximately 60 m intervals. The main or "steep veins" within each vein structure dip at 10º to 80° SE with an average of 30° and are offset by thrust faults dipping 5º N to 40° S with an average of 5º S. "Flat veins" usually weakly mineralized occur in the thrust faults between the "steep veins", thus forming the overall step-like vein structure. The mineralization is very irregular and changes a- long strike and down dip. It consists of thin veins of pure sphalerite and galena with quartz and pyrite. The thicknesses of the pure sphalerite and galena veins

Jan 1, 1977

By Y. Jeannin, C. Mannerskantz, F. D. Richardson

Measurements have been made between 1040o and 1300°C of the equilibrium between chromium metal, chromic oxide, hydrogen, and water. The results are in closer agreement with those deduced from recent thermal data than with previous equilibrium values. They lead to the equation ?G°1300°-1600°k = -266,700 + 59.95T ± 300 cal for the formzation of a mole of Cr2O3 from chromium and oxygen. This same equilibrium has been studied with the chromium dissolved in solid iron, and in this way chromium activities in Fe + Cr alloys have been established. The measuremenis show that there are substantial positive deviations from ideality in the a, and b phases, and support the results obtained by Heymer and Kubaschewski against those of other investigators. There is considerable disagreement between existing data,1"4 which is referred to in the Discussion, concerning the equilibrium Cr2O3 + 3H2 = 2Cr + 3H2O [l] There is also substantial disagreement between the results obtained by various investigators5-' who have measured the activities of chromium in its alloys with iron by the Knudsen effusion vapor pressure method. In view of the importance in metallurgical processes of chromium and its oxide and of Fe-Cr alloys, an attempt has been made to study equilib- rium [I] both with pure chormium metal and with chromium alloyed with iron, at temperatures between 1040o and 1300oC. From the work with the alloys it is possible to derive the chromium activities from the relationship

Jan 1, 1963

By R. R. Hartman, W. B. Agocs

In the course of a return flight from Olympia, Wash., to Laramie, Wyo., an airborne magnetometer profile was recorded continuously. The level of flight was controlled at barometric levels along segments of the flight. Barometric altitude was changed from 3000 ft to a maximum of 12,000 ft above mean sea level to take care of topographic variations. Terrain clearance varied from 800 to 7300 ft. Horizontal positions were obtained by recording and tying to cities, towns, airports, river crossings, and other landmarks in the course of the flight. Figs. 1-6 show the course of the flight and the general geologic and tectonic features traversed. The flight line begins south of Olympia, Wash., and proceeds south across the Puget-Willemette depression to the Columbia River. Thence it proceeds eastward along the Washington-Oregon border across the Cascade Mts. and lava flows and the Umatilla basin to Pendleton, Ore. From Pendleton it traverses the Blue Mts. uplift of Oregon in a southeasterly direction, and then to the Boise basin of southwestern Idaho. The flight line swings in an easterly direction as it passes over the Snake River downwarp to the south of the Idaho batholith. It then passes over the northern portion of the Great Basin and the heavily overthrust area at the intersection of the Utah, Idaho, and Wyoming borders. The flight then assumes an easterly course to cross the series of basins and uplifts of southern Wyoming and terminates near the western flank of the Laramie uplift.

Dec 1, 1956

By Eric K. Albert, J. Kiusalaas

The paper presents an overview of SPASID (Kiusalaas and Albert, 1983), a new computer program developed under U.S. Bureau of Mines funding for the prediction of surface subsidence caused by under- ground mining operations. The presentation, which is illustrated with two case studies, also re-evaluates the influence function method as a tool of subsidence prediction, arriving at some rather unconventional recommendations. SPASID consists of four modules that communicate through common data bases: (1) Preprocessor. This module prepares and maintains the database for the entire site. The database contains all the information about the site and the mine operation that is necessary for the computation of subsidence. (2) Subsidence Predictor. The influence function method is used to predict the surface displacements that occur in any portion of the site that occur between two given dates. The computations take into account the time lag between extraction and displacement, and the effects of pitching seams and incomplete compaction at the edges of panels. The program contains i not he's influence function and the Green's function of transversely isotropic elasticity theory. (3) System Identification. The purpose of System Identification is to determine the optimal values of the various parameters associated with the influence functions in the Subsidence Module. System Identification requires measurements of subsidence from a site with a sirnilar overburden structure. The values of the subsidence parameters are obtained by minimizing the discrepancy between the measured and computed surface displacements. (4) Postprocessor. The Postprocessor is a graphics facility for displaying the data generated by the other program modules.

Jan 1, 1984

By George Burgess

I. INTRODUCTION THE suggestion has often been made that it would be highly desirable, at least for certain grades of steel, to be able to control more certainly, by pyrometric measurement or otherwise, the temperatures of the operation of the open-hearth and other furnaces used in the manufacture of steel and iron. That the properties of the ingot and finally of the finished steel product are intimately related to the final temperatures attained by-the metal inn the furnace and to the temperature of casting, has been recognized by metallurgists for a long time, and this question has been very thoroughly treated, especially by Prof. Henry M. Howe, and by A. W. and H. Brearley.1 It is the object of this paper to demonstrate that in so war as casting temperatures of furnaces, steel ingots, and similar operations involving the temperatures of streams of iron and steel are concerned, well-known pyrometric methods s may be easily applied-if certain recently determined corrections are made and precautions taken-with a relatively high degree of accuracy. Greater but not insurmountable difficulties will be encountered in. the case of open-hearth furnace temperatures, while for" those of the converter type a ready solution does not seem practicable. It appears that certain essential data have always been lacking in reporting observations such as those of Le Chatelier in 1892. Thus the correction to be applied for the characteristic radiation-or emissivity¬has hitherto not been adequately taken into account nor the limitations of the several possible pyrometric methods clearly recognized.

Jan 2, 1917

By Philip Wilson

THE Province of British Columbia covers 382,000 sq. mi., about 250,000 sq. mi. of which have not been prospected. In fact, the coast country and the islands are so heavily timbered and the surface covered with so thick a mantle of soil, muskeg, and, over broad areas, glacial drift, that prospecting, and even trail breaking are extremely difficult. It is only along the coast or stream channels, or above the timber line, or where snow or rock slides have scoured the surface that rock outcrops can be found. Glaciers nestle in many of the cirques and fill the valleys in the higher ranges. Great ice sheets and perpetual snow persist in certain localities, thus reducing the exposed areas worth prospecting. Almost the entire country has been subjected to intense glaciation, so that the conspicuous oxidized outcrops of orebodies typical of the south-western United States and Mexico do not exist and surface bodies of enriched or oxidized ore are rare. With few exceptions, the mines1 of the Province are working primary ore. Developments have proved that some of these orebodies are large and important, although usually comparatively low in grade. Besides the few mines that have produced most of the minerals, there are many small mines, but their total output is unimportant. Considering the number of mines and prospects and the widespread mineralization, it is strange that no really great mines, comparable in size and richness with those in the western United States have been found.

Jan 8, 1922

By L. S. Pratt

IN 1910 the author was engaged in a qualitative study of the radio-activity of several chemical substances and a few minerals. In the course of the work he studied the mineral allanite (obtained from granite ledges at Topsham, Maine), and found it to be appreciably radio-active. Recently the fact was brought to his attention that the radio-activity of allanite is not well known, although Hon. R. J. Strutt in 1905 published a list of radio-active minerals with their analyses, including allanite from Amherst County, Virginia. In the work done, a standard ,type of electroscope was used, and the readings were made with a telescope, fitted with a scale, by means of which the rate of discharge could be readily determined. The natural "leak" of the instrument was carefully determined, and all results corrected accordingly. The method of study was as follows: The material to be tested was finely powdered, and spread over the bottom of a small, inactive pan. The electroscope was then charged, and the pan placed in position. The door of the instrument was closed, and the rate. of discharge carefully determined. All results were reduced to common form to permit of comparison. It is to be noted that the materials tested were not used in strictly comparable quantities, such as if 1 g. of. each had been used, but about the same quantity of powder was used (in the cases of the solid substances), so that the results are qualitatively accurate.

Jan 5, 1916

THE total crude production from the Dutch East Indies, and the British Protectorates of Sarawak and Brunei for 1932 is given in the following table: BARRELS BARRELS (42 GAL.) (42 GAL.) North Sumatra 4,226,935 Ceram 326,207 South Sumatra 13,956,157 Sarawak 2,739,650 Java 3,845,568 Brunei 1,322,725 Dutch Borneo (main island) . 9,406,733 Dutch Borneo (Island of Tara- kan) 6,579,184 Total 42,403,159 Production, which had shown a rapid increase from 1921 to 1929, has since been reduced. Exploitation drilling in the majority of the larger fields was suspended and existing production kept within predetermined limits by beaning. Most of the smaller fields were shut down entirely. The depth of producing levels varies widely in the different fields. Shallow fields with drilling depths to 500 meters (1650 ft.) are still numer-ous as well as those with depths between 500 and 1000 m. (3300 ft.). A few of the newer fields reach greater drilling depths. up to 1600 m. (5250 ft.). The deepest exploration well drilled to date (Djambi field, South Sumatra) reached a depth of 2332 m. (7650 ft.) before abandon-ment in March, 1930. The specific gravities of the various crude oils produced range between 0.65 (86.2° A.P.I.) and 0.95 (17.5° A.P.I.). The lighter crudes have a high gasoline content and fuel oils are derived from the heavier crudes, which usually are rich in paraffin.

Jan 1, 1933

By G. L. Spencer

There is no question as to the importance of the part played by the retort in modern zinc smelting. A satisfactory retort should have properties that will result in resistance to slagging action and fire cracks, and have no tendency, or at least only a small tendency, to soften and bend under furnace heat. The life and cost of a retort also are extremely important factors. The trend in zinc smelting during the past few years has been toward longer retorts and .higher charge density. This is caused by the fact that the diameter is limited to 9 or 10 in. because of heat penetration difficulties in larger sizes. Consequently, increasing the length of the retort and density of charge offers the only practical means of increasing the amount of zinc produced per retort. The stiff-ness of a retort perhaps is the most important factor, as slag accumulates in the bottom of a retort which has sagged and very quickly cuts through, often ruining the retorts below. The development of the high-silica retort is a result of the demands made by the trend toward heavy charges. Materials Used for High-silica Retorts The materials used in the manufacture of high-silica retorts at East St. Louis are fireclay, grog and silica flour. Analyses are given in Table 1. The fireclay comes from the St. Louis district. The grog consists of clean firebrick culls, and the silica flour, a very high-grade material, is purchased in the form of a flour that has been ground through 140 mesh.

Jan 1, 1931

By L. L. Davis

The rapid increase in the use of pulvcrulent adsorptive materials in the so-called "contact filtration" process for decolorizing lubricating oils makes it desirable to consider some of the basic principles involved. The commercial methods and types of equipment now used arc fairly well known, having been extensively described in the trade journals. In spite of this very little has been published concerning the factors which must be considered in the selection of a process or of a decolorizing ing material. It is commonly understood that contact filtration more or less closely follows the laws of adsorption. These principles have been thoroughly drscribed by Gurwitsch.' The contacting of neutral mineral oils seems to be adsorptive in character and apparently follows Freundlich's law of adsorption which may be expressed by the formula: X = Color material adsorbed hy the clay. M = Amount of clay used. C = Concentration of color material after equilibrium. A and P = Constants for a given oil and clay. Fig. 1 shows the decolorization curve for a natural, dark colored cylin-der stock when contacted with various quantities of clay, curve R being made with natural Riverside Texas fuller's earth and T being made with an acid-treated clay from Texas. As the Tag-Robinson color is inversely proportional to the depth of color, the reciprocal of these colors ran be assumed to be a funct ion of the concentratlion of coloring matter. The values of and C' can, therefore., br calculated by using the reciprocal Tag-Robinson colors, and when these

Jan 1, 1928

By Edmund Leaver

IT is generally recognized that the .addition of limited small amounts of various lead salts may aid the extracting power of the mill cyanide solution in the dissolution of silver from ores and in some cases may aid in the treatment of gold ores. Excess soluble lead compounds retard the dissolution of precious metals by the usual mill cyanide solution. Another phase of cyanidation is the use of the zinc-lead couple as an aid to better precipitation of gold and silver from solution containing a low percentage of cyanide. The chemistry of the use of lead salts in cyanidation has been dis-cussed by Clennell;1 the addition of lead salts in various cyanide mills is recorded by von Bernewitz;2 and the reasons for the use of lead salts in cyanidation have been explained by Clevenger.3 This paper deals with the adaptation of cyanidation to a different condition, in which the presence of lead minerals in a gold ore that is refractory to direct cyanidation complicates the treatment. If free gold is roasted in the presence of sulfur and lead salts, or if pyritic gold ores containing even a small percentage of lead minerals are roasted to free the gold from the pyrite, lead compounds coat the gold particles enough to make them almost insoluble in the usual mill cyanide solution contain-ing lime for protective alkalinity. Also, the lead compounds remaining in the calcine are slightly soluble in the mill solutions and such dissolved lead may retard the dissolution of the gold by the removal of oxygen or

Jan 1, 1933

By William Fink

ALTHOUGH age-hardening in an aluminum-base alloy containing magnesium was observed by Alfred Wilm1 as early as 1911, it was not until 1919 that a theory of the mechanism of age-hardening was proposed. Merica, Waltenberg and Scott,2 studying the age-hardening character-istics of Duralumin at the National Bureau of Standards, came to the conclusion that age-hardening of this alloy is caused by the precipitation of CuAl2, which is less soluble at the aging temperature than at the solu¬tion heat-treating temperature. It was postulated that the initially precipitated particles were of fine colloidal dimensions but that they gradually grew in size. Maximum hardness was assumed to be attained when the particles reached a critical size. This theory was at first received skeptically, since it was a widely accepted view at that time that the solid solution state should represent the hardest state of an alloy. Shortly thereafter, Jeffries and Archer proposed their well-known "slip interference theory."3 They suggested that age-hardening was accomplished by the precipitated particles acting as keys interfering with slip along crystallographic glide planes. They showed that this mechanical theory led directly to the assumption that maximum harden-ing would be produced by particles of a critical size, which they suggested would have a diameter approximately 10 times that of the aluminum atom. This contribution amplified and explained so rationally the age-hardening theory of Merica, Waltenberg and Scott that wide accept-ance resulted.

Jan 1, 1939

By F. B. Sherman, Keros Cartwright

Sanitary land filling has become one of the most widely used methods of disposing of solid refuse. A principal concern of regulatory agencies and the public itself is that landfill operations do not degrade the physical environment, including water resources, and the ground-water reservoir in particular. Knowledge of ground-water and engineering geology can guide landfill operations into suitable terranes or develop measures to compensate for natural limitations at a particular site. Experience and research in Illinois suggest four activities relating to landfill disposal that warrant attention by geologists and engineers: (1) regional delineation of favorable and unfavorable hydrogeologic conditions to facilitate planning and preliminary screening of potential landfill sites; (2) site evaluations, with considerations of geologic materials, topography, water levels, flow systems, and local occurrence and use of water resources; (3) research on aspects of the hydrogeologic environment that control effects of, or are modified by, landfills; and (4) formulation of practices in the siting, construction, and operation of landfills that prevent, mitigate, or isolate deleterious effects. The first two activities are basically in the domain of earth science, requiring the application of fundamental concepts of geology and hydrology and conventional site-exploration methods. The third activity, research, requires contributions from geology as well as other disciplines, including soil physics, sanitary engineering, and chemistry. The fourth calls for policy decisions by regulatory agencies and elected officials, using the contributions of scientists and engineers. Throughout history, man has disposed of unwanted materials by dumping. As urbanization has increased, haphazard dumping practices have given way to disposal under more controlled conditions because of increasing congestion of population and production of waste and greater concern for public health and environmental amenities. Many states and communities have already outlawed open dumping and open burning of refuse. The only practical methods of disposal of large volumes of refuse, therefore, are contained, high-temperature incineration, or burial in a sanitary landfill. In Illinois, regulation of solid waste disposal has been delegated to the Environmental Protection Agency. Each session of the legislature since 1965 has passed increasingly strict laws regulating waste diposal. As a result, the work of evaluating sanitary landfill sites has increased significantly for both the Department of Public Health, now the Environmental Protection Agency, and the Illinois State Geological Survey, which advises the Agency on matters of ground-water geology and pollution. In fact, our ground-water staff spends as much time on studies relating to waste disposal, primarily sanitary landfills, as on ground-water resource studies. Many other geological agencies are experiencing similar demands for increased assistance in solving waste-disposal problems. This paper summarizes some of the salient features of the sanitary landfill concept, describes activities of the Illinois Geological Survey in ground-water and engineering geology relating to landfills, and suggests policies that need consideration. A sanitary landfill is located and operated in such a way that vermin and pests, nuisances, and degradation of air and water are kept at acceptable levels. Some of the physical requirements of a sanitary landfill are all-weather roads for year-round access, fences to retain blowing paper, a daily cover of at least six inches of suitable earth material, and a final cover of at least 2 ft of earth material. Dumping into or adjacent to standing water generally is not allowed. Two common operating techniques are used. In the first, trenches are dug, the refuse is placed in them, and the earth removed from the trenches is used to cover the waste. In the second method, area fill, refuse is placed in low ground and covered with earth from adjacent high areas. The hydrology of the site is a prime consideration in locating sanitary landfills. Putrescible refuse, if saturated above field capacity, produces a leachate that usually has a high concentration of dissolved solids.2 As the leachate also acts as an agent for transporting bacterial pollutants, it constitutes a potential pollution hazard. To reduce the production of leachates, the topography of the landfill area should be such that surface water will not flow into or through the fill. Operations that will result in refuse disposal below or near the highest known water-table elevation may be required to take corrective or preventive measures to protect the ground water. In practice, under humid conditions such as prevail in Illinois, locations where disposal can take place above the water table are relatively few because surficial materials are commonly fine-grained, which permits slow gravity drainage and results in high degrees of saturation (100% moisture content) near the surface. At some sites, although disposal has taken place above the water table, ground-water mounds have developed, resulting in permanent saturation of the refuse. Permeability barriers usually are required to protect the ground-water reservoir from degradation by leachates. The convention in Illinois is to have a minimum of

Jan 1, 1972

By M. W. Burkart, B. Lustman

Uranium-base alloys exposed to high temperature water fail either by uniform oxidation or by sudden cracking and disintegration of the metal. The disintegration results from the oxidation of a second phase which is precipitated during the corrosion process. The precipitate has been identified as a metastable hydride of uranium. URANIUM-BASE alloys consisting of the body-centered-cubic ? phase are susceptible to two different modes of corrosion failure when exposed to high temperature water. In the first process, a smooth oxide film is formed on the metal surface which continually flakes off during exposure and results in a uniform weight loss of the specimen. The oxide is present as a thin, adherent layer whose thickness remains approximately constant. As the metal oxidizes during corrosion, a nonadherent layer is built up on this film and continually sloughs off. Coincident with the uniform corrosion just mentioned, another process occurs which eventually leads to failure of the metal by cracking and general disintegration. The failure takes place during a relatively short time compared to the total exposure. To distinguish this type of failure from the uniform corrosion, the cracking or disintegration of the metal will be referred to as discontinuous failure. For the ? phase uranium alloys it is discontinuous failure rather than uniform corrosion that limits the useful corrosion life of the alloy. This paper will be concerned primarily with the mechanism of discontinuous failure. Physical Changes During Corrosion—The alloys used in this investigation were ? phase uranium alloys containing 7 to 12 wt pet Mo or Cb. The preparation of the alloys, the method of corrosion testing, and the actual corrosion results are presented in another paper.' The ? quenching treatment consists of annealing the alloy for 24 hr at 900°C in a sealed Vycor glass tube filled with helium and then water quenching to room temperature without breaking the tube. The corrosion behavior typical of a ? phase uranium alloy is shown in Fig. 1. This specimen was a U-12 wt pet Mo alloy tested in pressurized, degassed water at 650°F. The corrosion rate was practically constant at 0.28 mg per sq cm per hr or increased slightly until about 15 to 20 days of exposure, when the onset of discontinuous failure occurred in this particular sample, and the specimen soon began to crack and disintegrate. The simultaneous increase in the observed corrosion rate is a result of the increased area of exposure due to cracking of the specimen. The microstructure of a specimen that failed by cracking is shown in Fig. 2. The presence of a plate-like precipitate can readily be seen. Metallographic examination of corrosion specimens reveals that the onset of discontinuous failure is always preceded by the formation of a plate-like second phase in the ? uranium matrix. Hydrogen analyses of specimens periodically withdrawn from corrosion test reveal that the hydrogen content of the alloy increases on exposure to the high temperature water, as shown in Fig. 3. The hydrogen is available as a corrosion product resulting from the formation of UO2 by the reaction of the alloy with water. Specimens analyzed just prior to discontinuous failure contained as much as 1200 ppm H, whereas the plate-like phase appears to precipitate out at a hydrogen concentration of between 10 and 25 ppm. The observed increase in hydrogen content prior to and during the formation of the plate-like precipitate suggests that this constituent may be a hydride of uranium. Additional evidence linking the identity of this phase to a hydride is that it can be removed by vacuum annealing at temperatures of 100°C and above. Decomposition products of the ? phase would certainly not dissolve at such temperatures, nor could other likely products of corrosion, such as oxides, be dissipated at any of the test temperatures. The precipitation and growth of the second phase during corrosion is accompanied by an increase in hardness of the specimen. The hardness increase results from the dispersion of the harder precipitated

Jan 1, 1959

By F. D. Hoyt, H. L. Hartman

The development of new processes and methods by The Pennsylvania State University to improve slate quarrying technology has centered in recent years on cutting and sawing stone in the quarry to eliminate a second cutting process in the mill. Two machines exhibit promise for this work: 1) a circular saw mounting diamonds or hard inserts to produce smaller sizes of stone and 2) a chain saw with insert cutting teeth to produce stone in the larger dimensions. Prototype machines have been constructed and tested in several Pennsylvania slate quarries, and one commercial installation has been operated for several months with a circular diamond saw. Other kinds of dimension stones may be cut by these saws. Research at Penn State has begun to study the fundamental cutting action of rotary tools or saws in slate and other dimension stones. A laboratory drill press is being instrumented to permit thrust-torque-rotational speed us penetration rate studies of single tooth cutting surfaces on stone. Machinability studies of slate conducted with tungsten-carbide inserts have been performed. The dimension stone industry generally accepts the rather basic premise that the larger the block removed from the quarry, the more practical and economical the operation. Thus, the concept of cutting to size any dimension stone while it remains in place in the parent bed would receive little consideration from the majority of members of the industry. However, the slate industry, which is usually considered a separate member of the dimension stone family, is pioneering in the development of an in-place sawing method. Before any final decision can be reached concerning a proposed new system, it is essential to take a long, hard look at the present method of operation in order to determine if the new system is indeed an improvement or even desirable. In the following section is a brief description of present quarry practice in the slate quarries of eastern Pennsylvania. PRESENT METHOD OF QUARRYING SLATE In the numerous slate quarries of Lehigh and Northampton Counties of Pennsylvania, the grain and cleavage of the slate are most often at right angles to each other; if a third surface is broken at right angles to these two natural planes of weakness, blocks of more or less rectangular shape can be separated.' In conventional quarrying a large calyx core drill prepares holes of 36-in. diam in which wire-saw standards are positioned. By wire sawing between strategically located core-drill holes, large sinks or benches of virgin slate are opened up. The sides freed by wire sawing will vary from quarry to quarry but generally are rectangular in shape with dimensions averaging 20 ft in length and about 15 ft in depth. Some quarries are fortunate in having a joint or natural parting to work to, which of course diminishes the amount of core drilling and wire sawing required. Once the various benches have been developed either through wire sawing alone or through a combination of wire sawing and natural jointing planes, the block removal proceeds in the following manner. A plug hole is drilled in the block with a compressed-air hammer and a feathering chisel is inserted in the hole to cause a fracture of the rock either with or against the grain as indicated by the positioning of the so-called feathers. This operation is referred to as sculping. After a block has been freed with and against the grain by means of wedging from the cross fracture with long bars or levers, the block is further freed along the cleavage plane by shimming it up with small wooden pieces in an operation known as styling. A large steel loading chain is wrapped around a block thus freed and the chain is attached to the wheel of an overhead cable. The block is then hoisted vertically to the cableway and moved along this cableway laterally to the lip or edge of the quarry. From here it is unloaded onto a rail car or truck for transportation to the processing mill. Except for occasional blasting to free stubborn blocks,

Jan 1, 1961

By Dirk A. Benham, William A. Warfield

INTRODUCTION Whenever a mine operator is faced with a decision between various mining methods or even equipment selection, he must be assured that his decision will have a positive effect on his economic operating goals. For instance, if a mine operator has a choice of using an LHD mining system or a slusher mining system, then his decision to use either must not only fit within the operational limitations of the mining plan (such as production requirements, physical features of the ore body, mine plant facilities, manpower requirements, etc.), but also assure that the ore is being extracted at the least possible cost. To aid in his decision making process, the operator will commonly compare acquisition costs, operating costs, maintenance costs, and the operational advantages and disadvantages of each system in addition to considering his personal observations and feelings. A decision to select a mining system using only those criteria aforementioned will not necessarily lead the operator down the path to maximizing profits. In addition, the operator should also compare the economic effects of each system upon the overall mining operation. A relatively simple method for determining the economic effects is to calculate and compare the break-even grades for each system under consideration. By implementing such an analysis, the operator can now select a mining system which can operate within the limits of the mining plan as well as extract the ores at the least possible cost, thus yielding maximum profits. This paper will present the geologic and physical conditions of a mine being operated by the Hypothetical Mining Company in the Grants Mineral District. An LHD and Blusher mining system are under consideration and are compared by examining operating costs, equipment availability, and the conventional operational advantages and disadvantages of each. Finally, the economic effects of each system upon the overall mine's operation are compared by utilizing break-even grade analysis. DESCRIPTION AND MINING METHODS The Hypothetical Mining Company has located an ore body in the Grants Mineral District. After extensive surface exploration drilling and cost considerations are evaluated, it is decided to open a mine. The following tasks must now be performed: 1. outline ore body and it's basic characteristics, 2. look at mining methods currently in use in the area, and 3. determine mining techniques and methods for exploitation of the ore body. For the sake of argument, the newly discovered ore body is located towards the western edge of the Grants Mineral Belt. The host rock for uranium mineralization is the Westwater Member of the Morrison Formation. The Westwater Canyon sands are overlain by the Brushy Basin Member of the Morrison Formation and underlain by the Recapture Member, all of Jurassic Age. Westwater Canyon sandstone is a fine to very course grained subarkosic sand with interbedded green and red mudstone. The Brushy Basin Member consists predominantly of greenish-gray mudstones and contains thin lenses of sandstone and a few thin beds of limestone. The Recapture Member consists of alternating thin beds of reddish brown, grayish red, and light gray sandstone and siltstone. The Recapture interfingers with the Cowsprings Sandstone in the area of the mine. The mineralization is based on the groundwater flow within the Morrison Formation. Primary ore distribution is based on three basic parameters: ore migration in a geochemical cell, lenticular mudstone interbedding, and enrichment along fault zones. In areas where two fault systems intersect, ore thicknesses of up to 30 m (100 ft.) are encountered. In those areas where the ore is well defined and thicknesses facilitate full face mining, the mining methods are determined more by ground or operating conditions, equipment availability, and access to working areas than they are in the fringe areas of the ore body where grade control is more important and split-shooting and break-even grade determines the mining technique. If a modified room-and-pillar mining method using systematic development is selected, better control of the ventilation, equipment utilization, and mining plan can be obtained. Figure I shows a typical mining area where the ore is thick,

Jan 1, 1982

By J. F. Smith, J. E. Davison

A value for the enthalpy of formation of z2 of -3.14 i 0.21 kcal per g-atom has been measured by the technique of acid solution calorimetry. This result is in quite good agreement with two earlier determinations by tin solution calorimetry and by direct reaction caloriinetry, and averaging of values determined from the three independent calorimetric techniques gives enhanced precision and accuracy with AHh8 (CaMgZ) = - 3.15 i 0.05 kcal per g-atom. For comparison with experimental data, values for the enthalpies of formation of CaMgz, SrMgz, and BaMgz of -9.8, -7.9, and -2.8 kcal per g-atom were estimated from a calculation based on the LVigizer-Seitz approximation as modified by Raimes for polyvalent elements. While complete quantitative accord between these calculated talues and available experimental data is lacking, nonetheless numerical accord is better than might be expected and, more importantly, parallel numerical trends are observed between experimental and calculated vnlues. WITHIN the past decade the enthalpy of formation of CaMg, has been determined a) from measurement of magnesium vapor pressures over binary Ca-Mg alloys,' b) by solution calorimetry with liquid tin as the solvent,' c) from measurement of hydrogen vapor pressures over ternary alloys of calcium, magnesium, and hydrogen,3 and d) by direct reaction alorimetr. The value from tin solution calorimetry is the most precise and is probably the most reliable, and this value is within the quoted uncertainties of the other three experimental results. The overall agreement among the four independent investigations is quite good, particularly so when the diversity of techniques is noted. On the basis of this agreement, CaMgz was chosen as a test material to evaluate the operation of a newly constructed apparatus for the determination of enthalpies of formation of intermetallic phases by acid solution calorimetry. This was believed to be a severe test because of the high chemical reactivity of both calcium and magnesium which reactivity presumably accounts for the fact that an early determination5 of the enthalpies of formation of Ca-Mg alloys by acid solution calorimetry yielded values significantly more negative than the four recent determinations. EXPERIMENTAL APPARATUS AND MATERIALS Experimental Apparatus. The enthalpy of formation of CaMg, was determined by measuring the difference between the heat evolved when dissolving the metallic compound and the heat evolved when dissolving equivalent amounts of unreacted metallic elements in hydro- chloric acid. This was done differentially with an apparatus consisting of twin calorimeters which were constructed to be as nearly identical as possible. The advantage of differential calorimetry is that systematic errors arising from the individual calorimeter design tend to cancel. A schematic representation of the apparatus is shown in Fig. 1. A dead air space around both calorimeters was provided by a large, thermally insulated jacket. Each calorimeter consisted of a 2-liter Dewar flask which was completely enclosed in a copper container. Each Dewar contained 1600 g of 2.5hr HCl to act as the solvent, and thermal effects resulting from solvent evaporation were minimized by covering the acid with 50 g of mineral oil. There was no detectable reaction between the acid and the mineral oil. Equivalent amounts of mechanical energy were added to the calorimeters through twin stirring rods which were driven at the same rpm by a single motor with the intent of the stirring being to maintain thermal equilibrium throughout the solvent. To calibrate the heat capacities of the calorimeters, known amounts of electrical energy could be added by passing measured voltages and currents for known times through submerged heaters, approximately 20 ohms, which were wound noninductively from Manganin wire. A 6-v storage battery was used as a power source, and a dummy heater was used as an exercise circuit to allow the battery to stabilize at a constant electromotive force before energizing one or the other of the calorimetric heaters. A type K-2 potentiometer was used to measure the potential drop across an energized heater while the current was determined from the potential drop across an external standard resistor. Times of energization were measured with an electric timer, and the electrical energy supplied to a heater

Jan 1, 1969

By G. E. Keller

In connection with the work of Committee D5, Coal and Coke, of the American Society for Testing and Materials in developing new standards and improving old standards, series of tests were made to check the variance of sample preparation and analysis of American coals. Table I in the "Tentative Method of Preparing Coal Samples for Analysis - 02013-62T" is rather complicated, and the tests were designed to develop data for the simplification of this table. An allowance of 20% of the total variance of sampling and analysis for the sample preparation and analysis steps was used. Also, instead of coals being grouped into ash ranges, they were grouped as washed and raw (unwashed) coals. As a result of these tests, a simplified Table I for Tentative Standard 02013 has been proposed. A standard test for laboratories to check their variance of sample preparation and analysis has been developed. Committee D5 on Coal and Coke of the American Society for Testing and Materials has been making a study of all standards applying to coal for the purpose of improving and bringing them up to date and for breaking some of the existing standards covering a number of tests into single standards. As an illustration, sample preparation is now partly covered in ASTM Designation D492-48, Sampling Coals Classified According to Ash Content, and partly in ASTM Designation D271-58, Laboratory Sampling and Analysis of Coal and Coke. The latter contains, in addition to parts of sample preparation, methods for determining Moisture, Ash, Volatile Matter, etc. Although revision of sampling methods and sample preparation methods are now assigned separately, it is possible that they may end up as one standard. One of the first new Tentative Standards developed as the result of these studies was ASTM Designation D2013, Tentative Method of Preparing Coal Samples for Analysis. Although this method is quite an im- provement over that in the old standards and gives very specific instructions, Table I (attached) is quite complicated and rather hard to understand. In order to take advantage of reduced quantities or weights, it is necessary to know the ash content within rather narrow limits before sample preparation and no distinction is made as to whether the coal is cleaned or uncleaned. No limits of accuracy are assigned to the sample preparation and analysis. The total over-all accuracy of sampling, preparation and ash determination as given in D492-48 has been specified for commercial sampling procedure as follows: "This procedure is intended for an accuracy such that if a large number of samples were taken from a single lot of coal, the test results in 95 out of 100 cases would fall within ? 10 per cent of the average ash content of the sample." Although Appendix 11, Method for Determining the Over-All Variance of Reduction and Analysis in the Tentative Methods for Mechanical Sampling of Coal, ASTM Designation D2234-63T, does give a method for determing the over-all accuracy of preparation and analysis expressed as variance and also the F test, it does not permit the determination of the variance at the various stages of reduction or of the ash determination. It was decided in 1961 to ask a number of laboratories to run a series of tests for the purpose of determining the variance at various stages of reduction and analysis with the view of simplifying Table I of the Tentative Standard D2013-62-T. This paper is a record of this series of tests with recommendations which resulted from the tests. At the same time and preceding these tests the International Organization for Standardization under Committee TC/27 WG 7 was studying the same problem. Tomlinson1 of England and Dr. paul2 of West Germany had made studies giving quite a bit of information. Also Schwerd and coryel13 published some information which was the main basis for the Mechanical Division provision in ASTM Tentative Standard D2013-62T, Table I. In checking with the various laboratories which offered to cooperate in these tests, none was found which used mechanical division through the entire preparation procedure. It was then decided to use riffles at all stages with the thought that if riffles gave satisfactory variances, approved mechanical

Jan 1, 1965

By R. V. Higgins, A. J. Leighton

Interest by petroleum engineers in the flow of three phases—oil, gas and water—in irregularly bounded porous media lies mostly in the performance calculation of water floods of reservoirs that have been partially depleted as the result of expansion of much of the originally dissolved gas. The authors present a method to forecast three-phase flow in complex geometry and explain the details by the use of a specific example of a five-spot water flood of a partially depleted stratified reservoir. In this example, the fluid and rock properties of a field given by Prats, et al,' were used. The computed results fit the field performance more accurately than Prats, et al, and Slider.' The time required for the high-speed digital computer to make the calculations, including the contributions from the different layered zones, is about one minute. INTRODUCTION The declining rate of discoveries of new oil fields in the United States makes the recovery of more oil from known reservoirs more attractive than previously. Water flooding has an excellent proved background for recovering additional oil economically. Accordingly, the main interest of this paper is in this type of recovery. In petroleum engineering studies, commercial interest in three-phase flow is mostly in the water flooding of reservoirs in which the oil has been partially produced by the expansion of dissolved gas. When water is pumped into these reservoirs, three-phase flow takes place. Although this paper is concerned with these conditions, the principles involved could be used for other conditions when and where they come to the fore. Many investigators have made contributions to non-empirical forecast methods using basic scientific engineering principles. Several of these used the oil in place at the start of the water flood and the oil remaining after a large quantity of water has passed through a core for key values in their calculations. Recently, Prats, et al,' and Slider have reduced assumptions by adding the third phase—gas—in their forecasting methods. Slider uses the mobilities in the immediate vicinity of inlet and outlet wells as an aid to simulate the resistance effect in the five-spat pattern of the flow of oil, gas and water. Prats, et al. minimize assumptions by using previously determined laboratory data for determining sweep efficiency in the five-spot pattern. In neither of these papers is the saturation profile continuously affected by permeability-saturation curves. Sheldon and Dougherty- recently described a method that employs continuously changing saturation profiles using permeability curves, has a minimum of assumptions and needs no prior sweep efficiency. The Higgins-Leighton method, described in this paper, has all of these features; however, many of the techniques are different from those of Sheldon and Dougherty. The Higgins-Leighton method, tested in May, 1961, is direct and easy to apply and requires very little computer time to calculate a forecast. The short computer time is especially helpful in the study of a reservoir containing many layers of different relative permeabilities. In the Higgins-Leighton method, the individual pressures do not have to be calculated, as the resistance to flow in each cell in the flow pattern is readily determined without the use of any iterative techniques. The saturation and permeability distributions are readily determined. These data and the shape factor, which is measured only once from the potentiometric model when mobility ratio is one, determine the resistance to flow in each cell. THEORY The authors showed in a previous paper4 that, as an aid to calculating performance, the reservoir can be divided into channels using the streamlines of a potentiometric model as a guide. See Fig. 1. This procedure also was used in this paper. The authors also showed that, by treating conduits as approximately one-dimensional and neglecting pressure gradients transverse to the main flow, the Buckley-Leverett equation may be expressed as The principles expressed by this equation are employed extensively in the three-phase flow, as they were in two-phase flow. In the three-phase flow, the channels (the size and shape of which are taken from a potentiometric model)

By W. D. Robertson, W. L. Phillips Jr.

Stress-strain curves were obtained for single crystals of alpha brass in tension and in direct shear. Specimens were strained various amounts in a given slip direction, unloaded, and immediately strained in a second slip direction 60°, 120°, or 180&apos; from the original slip direction. Crystals strained in tension and direct shear had comparable critical resolved shear stresses and stress-strain curves. The density of slip lines in direct shear and in tension was essentially the same. The stress-strain curves obtained in shear were independent of initial orientation, choice of {111 } slip plane, choice of <110> slip direction, prior annealing temperature, and rate of cooling after annealing. There was no recovery after annealing for 4 hr at room temperature or 200°C; recovery was observed after 4 hr at 400°C. The crystals showed no asterism and mechanical properties were completely recoverable up to 20 pct strain. It was found that there is a barrier to slip in all latent close-packed directions, and that the magnitude of these barriers, evaluated at 3 pct strain, is proportional to prior strain and independent of the choice of latent direction in the {111} plane. The formation of Cottrell-Lomer barriers is discussed as a possible explanation for the hardening of the latent systems. AN idealized concept of plastic deformation indicates that a single crystal should yield at some stress that is dependent on crystal perfection and it should then continue to deform plastically by the process of "easy glide," which is characterized by a linear stress-strain curve and a low coefficient, ds/dE, of work-hardening. Hexagonal metal crystals generally conform to this ideal concept of laminar flow. In face-centered cubic metals the range of easy glide is always restricted in magnitude and it is strongly dependent on orientation, composition, crystal size, shape, surface preparation, and temperature. Since one of the principal differences between the two crystal systems, both of which deform by slip on close-packed planes, is the existence of secondary (latent) slip planes in the face-centered cubic crystals, it has been proposed that the transition from easy glide to turbulent flow, characterized by rapid linear hardening, is due to slip on secondary planes intersecting the primary plane.&apos;-.; However, the characteristic differences between individual face-centered cubic metals remain to be explained; in particular, it is not clear why the range of easy glide should vary so greatly in different metals and alloys similarly oriented for single slip. An investigation and comparison of different metals with respect to latent hardening on the primary slip plane should provide some of the information required to specify the necessary and sufficient conditions governing the transition from easy glide to turbulent flow. But, in order to accomplish this purpose, plastic strain must be produced by simple shear in a chosen plane and in a predetermined direction by some form of directed shear apparatus, the results of which must be correlated with the corresponding tension experiments. Two such experiments have been performed previously with zinc and with aluminum. Edwards, Washburn, and Parker" and Edwards and Washburn7 found that the strain-hardening coefficients in two latent directions in the basal plane of zinc were the same as in the primary direction. However, to initiate and propagate slip in either the [2110] or the [1210] direction, following primary slip in the [1l20] direction, it was necessary to increase the stress above that required to continue slip in the primary direction; when the direction of shear was reversed 180 deg plastic strain began at a much lower stress than that required to initiate slip in the original direction and the stress to propagate slip in the reverse direction was lower than the stress to continue slip in the forward direction, indicating a permanent loss of strain-hardening. Rohm and Kochendorfer observed softening in aluminum for all latent close-packed planes and directions. They also found that the critical resolved shear stress obtained from their direct shear apparatus was 50 pct lower than the value obtained from conventional tension tests, that the stress-strain curve was linear at 50 pct plastic strain, and that slip lines were not visible at strains less than 30 pct. At present it is uncertain whether these diverse results correspond to real differences in work-hardening characteristics of the close-packed planes of aluminum and zinc or to differences in experimental technique. In view of Read&apos;s analysis &apos;" of the stress distribution in the experimental arrangement of Rohm and Kochendorfer, there is some reason to question the significance of the latter results. In order to resolve this problem it is necessary to re-valuate the direct-shear technique and either repeat the previous measurements or investigate a third system. The latter choice seemed most likely to produce significant results with respect to work-hardening, and accordingly, it was decided to examine the hardening characteristics of the latent slip directions in alpha-brass. The choice of alpha-brass was dictated by the fact that easy glide is more extensive in this alloy than in any other face-centered cubic metal or alloy and, presumably, more nearly like the idealized hexagonal system. Experimental Procedure Crystals were made in graphite by the Bridge-man method in the form of cylinders, 11/2 in. diam and 8 to 9 in. long. Material for the crystals was 70/30 brass containing the following impurities:

Jan 1, 1959