Search Documents

By H. H. Kellogg

A model of the slag-fuming process for recovery of zinc oxide fume from lead blast furnace slags, adapted to solution by a digital computer, is presented. The model incorporates the variaticm with time of the following: the fuming of zinc and lead, the change in the ferrous-ferric ratio in the slag, the transfer of sulfur to and from the slag, the temperature of the liquid slag, the temperature of the gases and fume which exit to the flue, the heat losses to the water jackets, and the amount of frozen slag on the water jackets. The assumptions which underlie the model-some of which are but crude approximations—are discussed. Despite some obvious shortcomings, the model simulates faithfully many of the important features of practical slag-fuming operations. The behavior of the model is compared with the operation of the American Smelting and Refining Co. fumzace at El Paso, Tex. The model is used to predict the effects on performance of changes in the coal rate, the temperature of the secondary air, and the composition of the coal. THE fuming of lead blast furnace slag for recovery of zinc oxide is standard practice today, and it has been the subject of several previous attempts at mathematical process analysis.'-' The mathematical process model described in this paper incorporates many of the features from the earlier studies, but it is a far more complete and realistic representation of the commercial process in that the following additional features have been included: the fuming of lead as well as zinc; the transfer of sulfur between slag and gas; the addition of slag feed in batches, over a period of time; tapping of the final slag over a period of time; the change of slag temperature with time. The additional features of the present model add greatly to the mathematical complexity, but this difficulty has been obviated by programming the model for solution by a digital computer. The IBM 7094 computer solves the model for one operating cycle of the fuming furnace in less than 1 min. It is doubtful if the same calculations could be completed with the aid of a desk calculator in less than a month. The computer program, written in the Fortran IV language, is too lengthy for presentation here.* Instead, this paper As shown in the sections which follow, it does simulate with remarkable faithfulness most of the known behavior of the industrial process. On the other hand, the model contains several gross simplifications of both the chemistry and heat balance, necessitated by the lack of more exact knowledge. In addition to these known weaknesses, it is not unlikely that those more intimately acquainted with industrial practice than the author will find other additions to or modifications of the model which will improve its utility and reliability. CHEMISTRY In brief outline, the present model treats the fuming furnace as two units, A and B, in series. In A the batch of slag reacts with the continuous stream of air (primary and secondary) and fuel injected at the tuyeres, to produce a stream of hot, reduced gases containing zinc vapor. The zinc content of both the slag and the product gas changes with time because of the batch nature of the process. Unit A is called the "lower furnace" in this paper; physically, it is considered to be that part of the fuming furnace which lies below the charge port. In B, the "upper furnace", the product gas from A is burned with the stream of "tertiary" air, to produce zinc oxide fume. The performance of B also depends on time because of the time dependence inherited from the product gas of A. The rate behavior in the lower furnace determines the important features of the process—the rate of elimination of zinc and lead from the slag, and the amount of fuel required for this purpose. Bell, Turner, and peters' published the first useful model of the lower furnace. They employed the assumption that, at any instant of time, the slag and reduced gas reach a state of equilibrium, according to the reactions: They cited only indirect evidence in support of their assumption of slag-gas equilibrium, yet several more recent laboratory studies of the activity of zinc oxide in slags4-8 have produced evidence which supports their view. On first acquaintance it seems unlikely that a high-output "rate" process like slag fuming would even approach an equilibrium state. The author, in an earlier study,' established, however, that the gas-slag interface in a fuming furnace was capable of such high mass-transfer rates that a close approach to equilibrium between gas and slag was quite probable. In devising the present model it was decided to assume a state of equilibrium between slag and gas at the outset, and then to modify this assumption as necessary in order to make the model agree with the be -havior of the actual process. Up to this time the assumption remains a part of the model, since no behavior

Jan 1, 1968

By M. R. Annis, P. H. Monaghan

The control of mud properties affords two practical means of tnitigating pipe sticking caused by differential pressure: (I) teducing weight and, therefore, differential pressure; and (2) reducing the friction berween the pipe and mud cake. This paper describes investigation of the second of these—the friction between the pipe and the mud cake. Friction between a steel plate and a mud cake, held in contact by a differential pressure, was measured in the laboratory while maintaining a constant area of contact. Experiments were performed to determine how this friction varied with changes in mud composition and with changes in experimental conditions such as the differential pressure, time of contact of plate and mud cake, and filter-cake thickness. It was found that the apparent coefficient of friction, or the "sticking" coeficient, was not a constant; instead, it increased with increased time of contact between plate and mud cake, and with increased barite content of the Mud. The sticking coeficient varied from about 0.05 to 0.2 afer 20 , and eventually reached values of 0.1 to 0.3 after two Hours. Quehracho or ferrochrome lignosulfonate reduced the sticking coefficient at short .set times but did not reduce the maximum value. Carboxy-~t~etlz~lcellulose had no effect on the sticking coeficient. Emulsification of oil in the mud reduced the sticking coefficient. Some oils reduced the sticking coefficient to about one-third of its Value in the oil- free base mud, while other oils reduced it only slightly. Addition of certain surfactants with the oils further reduced the sticking coefficient. Spotting a clean fluid over the stuck plate caused a reduction in sticking coefficient only if the differential presslrrr was reduced, either temporarily or- permanently. INTRODUCTION Often during drilling operations the drill string becomes stuck and cannot be raised, lowered, or rotated. This condition can be brought about by a number of causes, such as sloughing of the hole wall, settling of large particles carried by the mud, accumulation of mud filter cake during long stoppage of circulation and, finally, sticking by pressure of the mud column holding the pipe against the filter cake on the hole wall. This paper is concerned with the last-mentioned phenomenon. Helmick 2nd Longley' in 1957 suggested that a pressure differential from the wellbore to a permeable formation covered with mud cake could hold the drill pipe against the borehole wall with great force. This situation occurs when a portion of the drill string rests against the wall of the borehole, imbedding itself in the filter cake. The area of the drill pipe in contact with filter cake is then sealed from the full hydrostatic pressure of the mud column. The pressure difference between the mud-column pressure and the formation pressure acts on the area of drill pipe in contact with the filter cake to hold the drill pipe against the wall of the borehole. Helmick and Longley also presented laboratory cxperiments which showed that the force required to move steel across a mud cake increased with increasing differential pressure and with the time the stcel and mud cake had been In cuntact. Their data indicated that replacing the bulk mud with oil reduced the force required for movement. Field evidence was rcported that spotting oil over the stuck interval sometimes freed the pipe. Outmans- in 1958 presented a theoretical paper which described the sticking mechanism and explained the increase of sticking force with time with equations derived from consolidation theory. Since publication of these papers, there has been interest in the differential pressure sticking of drill strings, and several mud additives to reduce sticking or special equipment to free stuck pipe have been proposed."" Haden and Welch" have recently reported laboratory evidence showing that the composition of the filter cake influences the force necessary to move steel on the filter cake. There seems no doubt that differential pressure sticking is a real phenomenon and that its severity depends on the magnitude of the pressure differential across the mud cake, the area of contact and the friction between pipe and mud cake. The mud weight required to control a well is determined by the highest formation pressure in the well: hence, the magnitude of the differential pressure opposite normal or subnormal pressure formations cannot bc reduced. The area of contact may be minimized in several ways (control of filter-cake thickness, use of stabilizers and spirally grooved drill collars), but there arc practical limitations which prevent reduction of contact area from becoming a complete solution of the problem. However. the mud composition might bc altered to reduce the friction between pipe and mud cake. This paper presents quantitative measurements of the friction between steel and mud filter cake and shows how the friction varies with mud composition for given experimental conditions.

By S. R. Bardsley, S. T. Algermissen

Induction, nuclear and sonic well-logging methods were employed in a Green River formation oil-shale analysis and evaluation study conducted in northeastern Uintah County, Utah. The physical and chemical properties of an oil-shale section, previously cored and assayed by conventional methods, were used to evaluate the response of the various logs. The logging program was designed to measure variable properties of oil shale which relate to oil-yield potential in order that a relationship between assay-oil yield and log-determined properties could be identified, thereby permitting a direct determination of yield potential from logs alone. All of the major oil-shale zones and section ttlarkers are recognizable on the logs used in the study. The relationship between the response of the Density and Sonic logs and the assay-oil yield in gallons per ton was suficient to perinit the derivation of equations expressing the relationships. These equations can be used to determine the potential oil yield in gallons per ton of an oil-shale zone or section. The Neutron log response distinguishes the rich oil-shale intervals from the lean intervals, but does not appear to permit establishment of a quantitative relationship. The Garnma-Ray and Induction logs indicate only a qualitative relationship to oil-shale yields. Logging oil shale by Gamma-Gamrna Density and/ or Sonic logging methods will permit a fast, economical and accurate means of evaluating the potential yield of oil-shale deposits. Considerable sums of money have been allocated to Green River formation oil-shale evaluation during the past years by both private enterprise and Federal and state governments. The result of the work accomplished to date is commendable, but the task of fully exploring and evaluating one of the world's greatest reserves of potential energy for economical exploitation is enormous and much information is still needed. Present methods of evaluation consist primarily of sampling and assaying the oil shale for potential yield. The data received are excellent, but are both costly (inasmuch as it requires funds specifically allocated for the evaluation purpose) and time-consuming (as each representative sample must be assayed in the laboratory by specially trained personnel). At the present time, the Green River formation oil-shale province is one of the most active areas in the Rocky Mountain region for exploratory oil and gas drilling. This activity could play a twofold role and serve the function of spear-heading many oil-shale evaluation programs, as it could provide both cutting samples for assaying, geophysical data and modern well logs. This paper deals with a recent study conducted on Green River formation oil shale in which the application of induction, sonic and nuclear well logs to oil-shale evaluation was tested and proved. THEORY AND DEFINITIONS Oil shale may be described as siliceous marlstone, rich in solid organic matter called "kerogen". Kerogen is only slightly soluble in organic solvents, but it will decompose and yield oil vapors and gas when heated to destructive distillation temperatures at about 800 F. The mineral constituents of Green River formation oil shale are found in essentially uniform proportions with one another. The dominant types are, in the general order of abundance, dolomite, calcite, feldspars and quartz. Kerogen is also essentially uniform in its composition, and is about 80 per cent carbon and 10 per cent hydrogen by weight. The ratio of kerogen to the mineral constituents determines the richness or potential yield of the oil shale. This ratio also determines the total physical and chemical properties of the rock and provides a basis by which oil-shale richness may be determined from well logs. Because Green River formation oil shale was deposited in a lacustrine environment, the lithology is laterally consistent over wide areas. The vertical section consists predominantly of thin bands of alternating rich and lean oil shale which have been described by Bradley' as varves. The varves are occasionally broken by thin bands of volcanic ash and tuff and by zones of lean vugular oil shale. The effect that the thin non-oil shale beds and vugular zones would have on the well log analysis was a prime concern in the study. To cope with this possible problem, the logs used in the study were of two types: (1) logs believed to respond favorably to those properties of oil shale which are dependent upon the kero-gen-to-mineral ratio, these logs being the Gamma-Gamma Density log, the Sonic log and the Neutron log; and (2) logs that would respond to litho-logies and properties within the oil-shale section not associated with yield that might result in anomalous responses by the yield-measuring logs. Logs of the second type were the Gamma-Kay log, the Induction log and the Caliper log. THE PRESENT STUDY The present logging study was con-

By Leonard H. Goldman, Harold E. Marr

The PGT uranium assay probe is a borehole tool developed by Princeton Gamma-Tech over the last several years. It has the ability to do an in-situ assay of uranium in the presence of any amount of disequilibrium. It has some advantages over coring including cost, speed of analysis, and accuracy. In this paper we would like to give a brief description of the measurement and then show some sample logs from South Texas. Uranium exploration and development is carried out primarily by gamma logging since uranium daughters are prolific emitters of gamma rays. The conventional gross gamma tool for uranium logging is limited in value because of the inability of this tool to distinguish uranium from its daughters and other naturally occurring radioisotopes, such as potassium and thorium. This problem becomes severe in cases of disequilibrium. Disequilibrium, in a geological context, is defined as the condition when the gamma radiations from the daughter products are being emitted in a location different from that of the parent uranium. In the decay chain of uranium almost all the gamma radiation emitted in the entire chain comes from the daughter product, bismuth-214. Bismuth-214 is separated from uranium by several long-lived isotopes that are chemically active and have different physical properties, often resulting in shifts in the location of bismuth- 214 relative to the parent uranium. In the United States orebodies exhibiting disequilibrium are a common occurrence and the use of a gross gamma log to delineate uranium orebodies can lead to errors. At present the solution to the disequilibrium problem is extensive coring followed by chemical analyses of the cores. There are several drawbacks in using this technique. First is the high cost of coring, the second is the fact that no results are available for days, or typically, weeks after the drilling is done. Thus for development work, coring and drilling must be done on a grid basis and many additional holes are cored to ensure that the entire orebody is mapped. Another disadvantage to cores is the fact that a small volume is sampled, the volume of the core itself. This leads to problems in the mapping out of the orebody when the ore de- posit is not very homogeneous. The PGT probe described in this paper is a new solution to the disequilibrium problem. Basically, the probe measures radiations that come almost directly from uranium itself. The first daughter of uranium, which is protactinium-234 (Pa-234), is only separated from uranium by a 24-day half-life and no disequilibrium problems build up in such a short time. The PGT probe measures the intensity of a one MeV gamma line emitted by Pa-234 and, using this information, calculates the concentration of uranium. The PGT probe is 24" in diameter and 12 feet long. The probe contains a microprocessor which passes the information to a larger minicomputer in the truck. All data is analyzed on site, and the results from a high speed printer are presented to the geologist. Data is also available on 9- track IBM compatible tape for further processing. The PGT probe output is linear with uranium concentration. The only correction factor is for borehole size, and that only becomes important in boreholes bigger than seven inches in diameter. Dead time is compensated in the probe itself and no problems have been encountered in ore zones up to several percent UjO8. In addition to the uranium assay, a conventional gross gamma log is plotted alongside. Grade thicknesses for zones above cutoff are calculated as well as disequilibrium factors. COMPARISONS During its commercial operation PGT logged a series of 18 holes that had been cored and assayed. All of the holes in this series were logged in normal operation by regular field operators. The time to log each hole was generally under an hour, and in typical operation a PGT logging truck will do between 7 and 8 holes a day. The results of the comparison of the PGT and the core assays are presented in a series of figures showing plots of the PGT assay, core analysis and gross gamma measurements. The first three figures show individual holes with the gross gamma plotted along with the core and the PGT assays. All three logs were from holes on the reduced side of a rollfront deposit in South Texas. In Figure 1 we see the two wings of the roll- front at 143 ft and 150 ft separated by a barren zone. The wings are well defined both by the PGT assay and the core. There is approximately a one foot shift which can be attributed to drilling errors. The gross gamma is showing a rather severe discrepancy, being considerably lower and not showing the barren zone. The grade thickness calcula-

Jan 1, 1980

By M. Kashiwada

The zinc leach residues are introduced into waelz kiln to fume volatile metals and before the end of 1967, the waelz-fume containing zinc, lead, cadmium and indium was directly recycled back to the leaching process for the production of electrolytic slab zinc. However, since 1968, we have been recovering with success those valuable metals contained in the fume separately instead of direct leaching. According to the improved process, the waelz-fume, after being mixed with chloridizing agents, is fed into the rotary kiln to be roasted, wherein most of lead and cadmium content is collected as fume and most of zinc remains in the calcine. Zinc calcine thus obtained, containing 70 to 75 per cent zinc and, less than 1.0 per cent lead is sent to zinc plant for further recovery and the fume containing 40 to 50 per cent lead and 3 to 6 per cent cadmium is further processed to recover lead, cadmium and indium. The advantage of this process can be secured to the utmost when it is combined with the following subsequent treatments. (a) Blast furnace smelting of non-magnetic waelz slag to recover copper, silver and gold as matte. (b) Gallium recovering process from magnetic waelz slag. (c) Soda process of lead bearing cake produced after removing cadmium and indium from the said fume. Thus the extractions of zinc, lead and cadmium from leach residues account for 87 per cent, 72 per cent and 85 per cent respectively.

Jan 1, 1970

By Arnulf Muan, Klaus Schwerdtfeger

Equilibrium ratios C02/C0 of a gas phase coexisting with selected phase assemblages of the system Fe-Mn-0 have been determined in the temperature range 1000" to 1300°C. The oxygen pressure for the "hfnO" +hfn30, equilibrium and for the "(Fe,hTn)O" + (Fe,Mnh 0* equilibrium at high manganese contents has been determined by electromotive force measurements using stabilized zirconia as a solid electrolyte. The notstoichometry 01' "hTnO" and of "(Fe, iM1z)O" solid solutions has been determined by ther-mog-/avi?netry and by wet-chemical analysis. The data obtained are used to derive activity-composition relations in "(Fe,hfn)O" and (Fe,Mn),O4 solid solutions. WUSTITE "FeO" and manganosite "MnO" form a continuous series of solid solution at high temperatures,' and so do magnetite Fe304 and the high-temperature, cubic modification of Mn304 (Ref. 2) (high hausmannite, -1170). The oxides "FeO" and "MnO" are cation-deficient phases.495 The nonstoi-chiometry of "(Fe,Mn)O" solid solutions has been studied by Engell and ~ohl' at two selected C02/C0 ratios at 1250°C. The two oxide end members of the spinel solid solution, FesO4 and Mn,04, however, are known to be close to stoichiometric under the experimental conditions used in the present investigation.''' The oxygen pressures of "(Fe,Mn)07' solid solutions in equilibrium with iron have been determined by Schenck and coworkers,8 by Foster and welch," and by ~n~e1l.l' The two former groups equilibrated the condensed phases in C02-CO atmospheres of lmown compositions, whereas Engell" used a galvanic cell with stabilized zirconia as a solid electrolyte. The results of these investigators are not in good agreement. Activities of FeO in manganowiistite as calculated from the results of Foster and Welch show ideal behavior, those of Engell yield a pronounced positive deviation, and those of Schenck et 01. show a moderate positive deviation from ideality. In the present work oxygen pressures for the iron + manganowiistite and manganowustite + spinel equilibria and the nonstoichiometry of manganowiistites have been measured. The data were used to calculate activities in the manganowiistite and spinel solid solutions. EXPERIMENTAL METHODS The COz/CO ratios at which manganowustite and iron are in equilibrium were determined by thermo-gravimetric and quenching methods. Experimental details are described in a previous publication.'2 In the thermogravimetric technique, incipient reduction of manganowiistite pellets to metallic iron was observed as a break in the weight vs log COZ/CO curve. In the quenching technique, manganowiistite samples were partially reduced to metallic iron, or the metallic iron of manganowustite + metallic iron mixtures was partially oxidized to manganowustite, in atmospheres of constant C02/CO ratios. After quenching the composition of the oxide phase was determined by X-ray lattice parameter measurements and comparison with a standard curve obtained from oxide solid solutions of known compositions. The nonstoichiometry of "MnO" and "(Fe,Mn)07' solid solutions was determined by chemical analysis of samples equilibrated in C02-CO atmospheres and quenched to room temperature, as well as thermo-gravimetrically by reducing (Fe,Mn),04 or Mn304 to manganowiistite or manganosite. The equilibrium between manganowiistite and (Fe,Mn),04 was measured thermogravimetrically by reducing (Fe,Mn),04 solid solutions having composition in the range of %„ l(NFe +NM) from 0 to 0.63. No experiments could be performed with this technique at higher manganese contents, because the equilibrium C02/C0 ratios are too large for accurate control. An additional difficulty arises at the higher manganese contents due to the strong increase in oxygen content of the manganowustite phase with increasing log Py near the manganowiistite-spinel boundary. Consequently a sharp break in the weight loss vs log C02/CO curve cannot be observed at the phase boundary. At high manganese contents of the manganowiistite, e.g., (NMn/(NF~ + NMn) > 0.9, electromotive force measurements with stabilized zirconia as a solid electrolyte were made to determine the equilibrium oxygen partial pressure. Experimental details are described in a previous paper.* Mixtures of "(Fe,Mn)O" and (Fe,Mn),04 were pressed to pellets, and the oxygen pressure of the equilibrated samples was compared to that of Ni + NiO mixtures in the cell The composition of the manganowiistite in the equilibrated two-phase mixture was determined by lattice parameter measurements and comparison with known standards. The oxygen pressure for the Ni + NiO equilibrium was taken from available data.l3~l4 No reliable results were obtained with the electromotive force technique on iron-rich oxides. The electromotive force drifted strongly with time in this composition range. An additional difficulty arises from the partial de-

Jan 1, 1968

By Wolfram Ruff, H. A. Schwartz

THE spheroidal form of the temper carbon nodules in malleable cast iron and of the graphite mottles of "mottled" cast iron suggests that in both all the graphite in a given mottle or nodule grew from a single center of crystallization or nucleus. ‡ There is, however, a distinct metallographic difference between the mottle and the nodule; the area of mother metal impoverished in combined carbon by the crystallization of graphite in a mottle is practically coextensive with the ramifications of the graphite, while the impoverished zone of metal corresponding to a given nodule is always larger, and usually much larger, than the approximately spherical mass of graphite crystals forming the nodules. Furthermore, the mottle probably is formed during freezing and the nodule almost always at a considerably lower temperature. Assuming that the nodules or mottles can be used as a measure of the existing nuclei (capable of germination) we propose to record certain observations as to the graphitizing reaction in the light of the number and habits of growth of these nuclei. The present authors, in cooperation with others 1-7, have reported upon various cognate aspects of the problem. The fact that temper carbon is a mass of flakes and not a solid granule has become well recognized since the introduction of an improved polishing technique8,9,10 for cast iron. The problem of deriving from the circular planar intercepts

Jan 1, 1935

By L. M. Barker

THE New Cornelia Branch of the Phelps Dodge Corporation is at Ajo, Pima County, Ariz. It is at the southern terminus of the Tucson, Cornelia and Gila Bend Railroad, which connects with the Southern Pacific Railroad at Gila Bend, Ariz., approximately 43 miles to the north. HISTORY Early history of the Ajo district has been related by A. W. Allen1 and by T. A. Rickard.2 Briefly, steps looking to the large-scale development of the ore body were instituted as early as 1912. This work culminated in the equipment of the property for open-pit mining by steam shovels. Ores initially mined carried economic amounts of copper carbonates as the principal copper-bearing mineral. Treatment methods developed for the extraction of the copper content involved leaching and a 5000-ton leaching plant was constructed and placed in operation in early 1917. Description of methods and equipment employed in this plant has been given by A. A. Tobelmann and James A. Potter.3 As exhaustion of the carbonate ore body neared, and mining operations exposed an adequate tonnage of sulphide ores, a 5000-ton concentrator was constructed for their treatment. That plant has been described by H. Kenyon Burch.4 Construction was completed and the plant was placed in operation in early 1924. Changes made in the original plant to improve practices and increase production will be the subject of subsequent paragraphs of this paper.

Jan 1, 1939

By L. G. Austin

INTRODUCTION Autogenous (including semi-autogenous) grinding has probably been the most important single innovation in milling practice for the last twenty years. However, the design of these units has been largely a matter of trial-and-error, since the normal empirical laws for the design of ball mill circuits do not apply with exactitude to autogenous grinding circuits. There have been examples of autogenous mills failing to achieve output or product specifications. It is worthwhile, therefore, to attempt to develop a more detailed and precise set of design laws, using the concepts of specific rates of breakages and daughter fragment distributions (1), and performing mill simulations by computer. This type of approach has been applied to ball and rod milling (2, 3,4,5), but even for these mills it is by no means complete as yet (6), because of the amount of experimental work involved. There has not been a strong incentive for industry to develop new design procedures in ball and rod milling because the prior back-log of experience with these mills makes for easy design by empirical comparsion with existing systems. The new approach has been followed mainly by University groups (7,8,9,10), although experience in Australia (9,11) has shown the advantages of the approach. Stanley (12) has applied the approach to results from a large autogenous mill, and we will use many similar concepts to his work, but extend the concepts to a more

Jan 1, 1977

Henry C. Carlisle: This is a husband-and-wife act, in which Mary Carlisle is going to listen, and break in as often as she feels like it. I am going to describe my career as a mining engineer. We are at Nantucket, in the 75 Main St. house; The year is 1959. Q: This is something the boys and I have wanted you to do for a long time. Carlisle: After leaving Columbia in 1910, I arrived at Ray, Ariz., January 1, 1911, and rustled a job from Louis Cates, Ralph Nowland and Sprott Boyd, who were running the Ray mine. I went to work as a surveyor's helper, made $90 a month, and paid $35 a month board. I lived in a dormitory where about 25 other engineers, graduates from different colleges, were living. It was very social and you made a lot of young friends early in the game. I did not think much of the idea of being a surveyor, or even a surveyors, helper; the higher-up surveyors only got $125 a month, and had been there quite a long time. So, I asked to be changed to underground sampling, where I would see the mine faces every day and learn more about mining. In about three months, I became an underground sampler and remained at this for a year, but in three months I was promoted to head sampler, with six people under me.

Jan 10, 1963

By R. B. Sosman, J. C. Hostetter

We have shown in the preceding paper that practically all natural oxides of iron contain a determinable percentage of ferrous iron, and in many cases the percentage approaches that in magnetite itself. Some of these oxides are true homogeneous solid solutions. Others are not homogeneous, and can be separated magnetically into fractions. The nature and cause of this inhomogeneity in certain special cases form the subject of the present paper. Magnetic FRactionation of Oxides of Iron The magnetic fractionation of a sample of oxide can be conveniently carried out by powdering the material very fine, and exposing it at various distances from the poles of an electromagnet. The magnet that we used was specially designed1 to give a strong field together with a steep gradient outside of the poles. It is set in a frame, with the pole pieces directed downward. A glass plate can bc adjusted at various distances beneath the poles. If the fine iron oxide powder is placed just beneath the glass plate, successive portions of the powder are picked up by the magnetic attraction and are caught against the glass plate, the most magnetic portions being taken up at the greatest distance from the poles. Some natural oxides can thus be separated into several fractions of different magnetic susceptibilities. Among other natural iron oxides, we examined the powder obtained by crushing some crystals of hematite from Elba.2 We found that

Jan 1, 1918

By R. B. Sosman

INTRODUCTION WE have shown in the preceding paper that practically all natural oxides of iron contain a determinable percentage of ferrous iron, and in many cases the percentage approaches that in magnetite itself. Some of these oxides are true homogeneous solid solutions. Others are not homogeneous, and can be separated magnetically into fractions. The nature and cause of this inhomogeneity in certain special cases form the subject of the present paper. MAGNETIC FRACTIONATION OF OXIDES OF IRON The magnetic fractionation of a sample of oxide can be conveniently carried out by powdering the material very fine, and exposing it at various distances from the poles of an electromagnet. The magnet that we used was specially designed 1 to give a strong field together with a steep gradient outside of the poles. It is set in a frame, with the pole pieces directed downward. A glass plate can be adjusted at various distances beneath the poles. If the fine iron oxide powder is placed just beneath the glass plate, successive portions of the powder are picked up by the magnetic attraction and are caught against the glass plate, the most magnetic portions being taken up at the greatest distance from the poles. Some natural oxides can thus be separated into several-fractious of different magnetic susceptibilities. Among other natural iron oxides, we examined the powder obtained by crushing some crystals of hematite from Elba.2 We found that

Jan 6, 1917

By John H. Hollomon

In a recent paper,' a very early suggestion by Ludwik2 concerning the nature of the mechanical behavior of metals has becn reexamined and extended. In essence it was suggested that there exists, at least under certain conditions, a mechanical equation of state; that the stress required for flow depends upon the instantaneous values of the strain, strain rate, and temperature, and not upon their past values. It is proposed that under these circumstances thc stress does not depend upon past history of these variables, but is like the temperature of a gas that depends only upon the instantaneous values of the pressure and volume. This notion has not been applied to present-day studies of metals, though it is especially applicable to the study of creep. It is the purpose of this paper to analyze the significance and possible range of applicability of this idea and to determine how it influences the accepted ideas concerning creep. Stress-strain Relations It is wcll known that the stress-strain curves of metals are influenced by both train rate and temperature. For a fixed strain rate and temperature there is associated with each metal a stress-strain curve. If either the strain rate or temperature is changed a new stress-strain curve will be characteristic (Fig. I). A much more genera1 relation between the effects of these variables is possible, however. Consider the stress-strain curves of Fig. I determined at

Jan 1, 1947

By John H. Hollomon

In a recent paper,' a very early suggestion by Ludwik2 concerning the nature of the mechanical behavior of metals has becn reexamined and extended. In essence it was suggested that there exists, at least under certain conditions, a mechanical equation of state; that the stress required for flow depends upon the instantaneous values of the strain, strain rate, and temperature, and not upon their past values. It is proposed that under these circumstances thc stress does not depend upon past history of these variables, but is like the temperature of a gas that depends only upon the instantaneous values of the pressure and volume. This notion has not been applied to present-day studies of metals, though it is especially applicable to the study of creep. It is the purpose of this paper to analyze the significance and possible range of applicability of this idea and to determine how it influences the accepted ideas concerning creep. Stress-strain Relations It is wcll known that the stress-strain curves of metals are influenced by both train rate and temperature. For a fixed strain rate and temperature there is associated with each metal a stress-strain curve. If either the strain rate or temperature is changed a new stress-strain curve will be characteristic (Fig. I). A much more genera1 relation between the effects of these variables is possible, however. Consider the stress-strain curves of Fig. I determined at

Jan 1, 1947

By AIME AIME

Few men in the coal-mining industry have had experience in metal mining as well, as has Carroll A. Garner. He went to the Arizona copper country immediately after graduating from Penn State in mining engineering in 1910, and worked in the engineering departments of the Miami and Inspiration companies for two years. Then he came back to Penn State far a year as an instructor in mining engineering before embarking in the coal industry. He was born in Ashland, Pa., July 6, 1889, and reared there, in the heart of the anthracite district, which undoubtedly influenced his choice of a professional career. The green Pennsylvania hills were preferred to the Arizona cactus country. His first coal-mining job was with the Lehigh Valley Coal Co., of which he was division engineer at Hazleton when he joined the Institute in 1917. He gave that up to go to Ohio as head of the Fernwood Mining Co. in 1921, but even that was too far west and after two months he was back in Pennsylvania as assistant general manager of the company that has since monopolized his services the Jeddo Highland Coal Co. Since 1927 he has been vice-president in charge of operations of both the Jeddo-Highland and the Hazle Brook Coal Companies, Jeddo, Pa. Between them they normally produce about 1,500,000 tons of what Mr. Garner will readily admit is the very highest grade of anthracite, utilizing the services of some 2600 men.

Jan 1, 1942

By Richard H. Terhune

The use of water-cooled breast-jackets or cinder-tap blocks is a great convenience in lead-smelting, even when siliceous slags are made. If the charges are at all basic it is almost imperative. Jackets of riveted wrought-iron or steel are expensive; those of cast-iron are liable to crack; those of bronze are costly and not durable, being easily penetrated by tapping-bars or destroyed by streams of matte impinging against them. To overcome these objections I introduced at the Hanauer works, in April, 1886, castjackets of steel, which have been in constant use since that time and are to-day as good as new. These jackets were made for us by the Chester Steel Castings Company, of Chester, Pa., at a cost of ten cents a pound at the works of that company. The metal is 5/8-inch thick, and the jackets were cored and tapped for l1/2-inch bushings, affording two large holes for the removal of dirt and incrustations. The same holes are used for feed- and discharge-water through 3/4-inch pipe. I hope the successful introduction here of cast-jackets of steel will lead to their more extended use in all branches of metallurgy where water-cooled surfaces are severely taxed, and where the size and thickness of the castings are not unfavorable to the production of a sound article, impervious to water and of high tensile strength.

Jan 1, 1889

By Ben Gumpertz

THE important factors in any study of the screening of sand with a gravel enve-lope, as applied to use in oil wells, are: (r) sand size and shape, (2) gravel size and shape, (3) ratio of gravel size to sand size, (4) flow velocity, (5) viscosity of the fluid. Perhaps the first extensive investigation of the function of gravel in screening sand was performed by Coberly and Wagner,1 from which the following conclusion was drawn: "The diameter of the largest grains in a single classified sand suitable for gravel packing is approximately 23 times the grain size at the ten-percentile analysis of the formation sample." This applies to sands classified by Tyler screens and is for gravel grains of the maximum size that could be used to form a stable bridge. Field practice has shown that the screening effect of a given gravel for a given sand apparently varies with the flow velocity.2 Also, it has been assumed by some opera-tors that the thickness of the walls of the gravel envelope surrounding the well has little effect upon the screening process. It is thought by others that a narrow envelope of gravel might form an ineffec-tive screen. Thus the purposes of this work are: I. To investigate the effect of gravel-sand size ratio upon screening action under the condition of varying flow velocities. 2. To investigate the effect upon screen-ing action of varying the thickness of the gravel screen.

Jan 1, 1940

By Kung-Lee Wang, Brian W. Mackenzie, Warren E. Morrison, DeVerle P. Harris, George F. Sharrard

The term "mineral economics" is applied to a wide range of activities in the mineral industries. Earlier chapters have described the application of economic concepts to the mineral industries-supply, demand, conservation, tariffs, etc. The solution of mineral economics problems is often assisted by the application of quantitative methods. The purpose of this chapter is to describe a number of quantitative methods-econometric, operations research, and management science techniques-which find application in the analysis of mineral economics problems. These methods include input-output analysis, trend analysis, forecasting techniques, simulation, multivariate statistical analysis, mathematical programming, and market research techniques. The purpose of this introductory section is to provide a mineral economics framework for the application of these methods. Mineral economics is a subdivision of economics that is justified by a sufficient number of economic problems in the mineral industry requiring special experience and an unusual combination of skills. These problems are concerned with the conversion of minerals as geologic resources to minerals as economic goods. The mineral conversion process is outlined in Fig. 8.A.1. The physical occurrence of mineral deposits in nature and the market demand for mineral products in the economy provide the basic stimuli. The conversion process embodies a number of sequential stages-exploration, the development of mineral deposits, and mineral processing facilities and, consequently, productive activity to supply market demand. Changes in demand and the depletion of deposits illustrate the dynamics of the process. Mineral economics applies economic con-

Jan 1, 1976

By Victor Homerberg

A STUDY of the correlation of the mechanical properties, and of the microstructure with the heat treatment of 60-40 brass has been confined, heretofore, to the rolled or extruded material as received from the manufacturer. The results obtained by Babson and Buhler,1 Bengough and Hudson,2 Stead and Stedman,3 and Brayton4 have been confined to the treatment of the material as received. No attempt was made to get the material into a given condition and then to work from this basis. To start with a given structure would have the decided advantage of making the work independent of the original condition, hence, to make the results reproduceable. In a previous paper, it was shown, in connection with the study of the transformation that occurs at about 470° C., that if specimens were quenched to produce the beta structure and then reheated, the beta would begin to break down, at approximately 200° C., into a very finely divided alpha. It was predicted that important results might be obtained if test pieces were to be given a similar double heat treatment and then tested for the mechanical properties as well as a study of the microstructure. The material used in the present investigation was a ¾ -in. round bar of extruded muntz metal of the following composition: Copper, 61.05 per cent.; zinc (by difference), 38.90 per cent.; lead, 0.05 per cent.; iron, trace; tin, nil.

Jan 3, 1924

By William Fink

THIS paper is the nineteenth of a series from the Aluminum Research Laboratories, presenting the results of the investigations of equilibrium relations in aluminum-base alloys made from electrolytically refined aluminum. In previous papers equilibrium) relations have been deter-mined and correlated for 12 binary systems. Equilibrium relations have also been determined for portions of the aluminum corners of three ternary systems (aluminum-iron-silicon, aluminum-magnesium-silicon and alu-minum-copper-magnesium). The object of the present paper and those to follow is to increase our knowledge of the aluminum corner of the more important ternary systems. In 1926 Dix and Keith? suggested a new method for designating the phases encountered in alloy systems. The system has been used to a very limited extent 1,2,3. The system has since been slightly modified and will be used in this and future papers. In the system as modified, a phase is designated by placing in parentheses the chemical symbols of the elements essential to the formation of that phase. The symbols in the parentheses are separated by dashes in order to clearly distinguish them from a chemical formula. Elements that are not necessary to the formation of the phase in question, but which may be present in solid solution, are not indicated in the designation. If two or more phases would have the same designation according to these rules, they are dis-tinguished by prefixing Greek letters, and are definitely identified by X-ray diffraction patterns.

Jan 1, 1936