Search Documents

By W. J. Millard

It is well known that the excellent mica from Brazil played a most vital role in World War 11. Increased production from Brazil was necessary and with the assent of the Brazilian Government engineers from the united' States went down to study the problem. One of the means advocated by a former Chief of Metals and Minerals Branch of the Board of Economic Warfare, Mr. Carl Schwegler, was the use of stripping machinery. On a pegmatite dike favorable for stripping, a small number of miners could produce as much mica per day as an underground mine employing many times the same number of men. Type of Deposit Favorable The most favorable type of pegmatite for stripping is that which lies more or less parallel to the surface of the slope of a hill. Pegmatite dikes that cut directly into a hill are not suitable for stripping except where a long outcrop extends along the slope. Then just the outcrop could be stripped to some advantage. The ratio at no time should be greater than 1: 3; i.e., I cu. m. of pegmatite to 3 cu. m. of waste, unless the pegmatite was extremely rich throughout the dike. The Economics of Stripping When a mineral is badly needed to win a war, not too much heed can be paid to costs. The object is to produce rapidly and in quantity. Again, a deposit containing a superior grade of mica may be worked although the pegmatite is more costly to work than another deposit containing a considerably greater amount of poor-grade mica. For example: one deposit may have a little mica that will run 11 per cent good stain and better when trimmed and contain 2 kg, of crude mica per cubic meter of pegmatite, while another may run 0.2 per cent of good stain and better, and have a mica content of 10 kg. per cubic meter. A number of stripping projects were found in the vicinity of Raul Soares, Minas Gerais. These were sampled in the various old workings by cutting out a cubic meter of pegmatite and saving the usable mica. Because of the proximity to the surface of most stripping projects, about 34 per cent only of the mica is good for trimming. The other 66 per cent is too badly weathered to be of use. In Table I are given data collected on five properties near Raul Soares. In Table I, "value per cubic meter of pegmatite" means the value of the qualified mica obtainable. This does not include the half trimmed and splittings. By "value per cubic meter of matter" is meant the value of the qualified mica per cubic meter of material excavated; i.e. both waste and pegmatite. This is the figure that should be used to determine whether the operation will be profitable or not, as the cost of stripping is about $0.14 per cubic meter. With new machinery not subject to breakdowns, the cost per cubic meter should be around $0.10 to $0.15. To this should be

Jan 1, 1948

By W. J. Millard

It is well known that the excellent mica from Brazil played a most vital role in World War 11. Increased production from Brazil was necessary and with the assent of the Brazilian Government engineers from the united' States went down to study the problem. One of the means advocated by a former Chief of Metals and Minerals Branch of the Board of Economic Warfare, Mr. Carl Schwegler, was the use of stripping machinery. On a pegmatite dike favorable for stripping, a small number of miners could produce as much mica per day as an underground mine employing many times the same number of men. Type of Deposit Favorable The most favorable type of pegmatite for stripping is that which lies more or less parallel to the surface of the slope of a hill. Pegmatite dikes that cut directly into a hill are not suitable for stripping except where a long outcrop extends along the slope. Then just the outcrop could be stripped to some advantage. The ratio at no time should be greater than 1: 3; i.e., I cu. m. of pegmatite to 3 cu. m. of waste, unless the pegmatite was extremely rich throughout the dike. The Economics of Stripping When a mineral is badly needed to win a war, not too much heed can be paid to costs. The object is to produce rapidly and in quantity. Again, a deposit containing a superior grade of mica may be worked although the pegmatite is more costly to work than another deposit containing a considerably greater amount of poor-grade mica. For example: one deposit may have a little mica that will run 11 per cent good stain and better when trimmed and contain 2 kg, of crude mica per cubic meter of pegmatite, while another may run 0.2 per cent of good stain and better, and have a mica content of 10 kg. per cubic meter. A number of stripping projects were found in the vicinity of Raul Soares, Minas Gerais. These were sampled in the various old workings by cutting out a cubic meter of pegmatite and saving the usable mica. Because of the proximity to the surface of most stripping projects, about 34 per cent only of the mica is good for trimming. The other 66 per cent is too badly weathered to be of use. In Table I are given data collected on five properties near Raul Soares. In Table I, "value per cubic meter of pegmatite" means the value of the qualified mica obtainable. This does not include the half trimmed and splittings. By "value per cubic meter of matter" is meant the value of the qualified mica per cubic meter of material excavated; i.e. both waste and pegmatite. This is the figure that should be used to determine whether the operation will be profitable or not, as the cost of stripping is about $0.14 per cubic meter. With new machinery not subject to breakdowns, the cost per cubic meter should be around $0.10 to $0.15. To this should be

Jan 1, 1948

By A. G. Guy

Zinc vapor from a reservoir of liquid zinc maintained at lower temperatures was diffused into sets of copper-zinc alloys at 759° and 870° C and into sets of silver-zinc alloys at 650° and 700° C. Each set of ,four copper-zinc alloys consisted of pure copper and 90/10, 80/20, and 70/30 brass. Similarly the set of silver-base alloys consisted of specimens containing 0, 7, 15, and 20 pct Zn. Natural markers at the initial surfaces of the specimens ware "trapped" under a thin electroplate and their depth of burying was measured after diffusion. The ratio of diffusivities of the two components determined from these data and the chemical diffusion coefficient calculated by the Matano method agreed with previously reported results. The line of markers was irregular and was often discontinuous when a grain boundary was crossed. TECHNIQUES involving the vapor phase have been widely employed in studying diffusion phenomena in metals. Many investigators have evaporated the more volatile component from an alloy, but it is generally believed that the porosity created under these conditions interferes with adequate interpretation of the experimental results. The extensive work of Gertsriken6 has been criticized on this score. Accary1 found that the diffusion coefficient for de-zincification of brass is larger by a factor of five than that for zincification, although he attributed the difference to a higher vacancy concentration under conditions of dezincification. Balluffi and siegle2 thoroughly investigated the technique of adding a more volatile component to a less volatile base metal as a means for studying diffusion. They verified that no porosity forms in a brass under these conditions and that the diffusivities of the two components can be determined from observations of the motion of markers originally placed on the surface of the specimen. The mathematical analysis that they developed for treating the experimental data was modified in a later note, but essentially it involved using the graphical Boltzmann-Matano method that is customarily applied to solid-solid diffusion couples. The experimental method used in the present research was similar to that employed by Balluffi and Siegle except for two modifications. Balluffi and Siegle used alloy chips as the source of metal vapor. This procedure has the disadvantage that the concentration of solute at the surface of the specimen changes during the diffusion experiment as the alloy content of the chips is gradually decreased. This disadvantage was overcome by employing liquid zinc as the source of zinc vapor in a manner similar to that described by Herasymenko.9 There was then no limitation on the amount of solute usefully available, and several relatively large specimens could be diffused in a given experiment. The second modification was the use of natural markers on the surface of the specimen rather than larger, artificial markers, such as the alumina powder employed by Balluffi and Siegle. It was expected that the fine, natural markers would permit more precise measurement of the buried interface as in the case of ordinary sandwich specimens.10 EXPERIMENTAL The experiments were designed so that zinc from the vapor phase would maintain a constant zinc content at the surface of pure copper (or silver) and

Jan 1, 1960

By M. E. de Morton

Recovery and early recrystallization of heavily deformed, 99.98 pct Cr was investigated by studying metallographic structure. X-ray line sharpening, electrical resistivity, plastic properties, internal friction, and shear modulus. Appreciable recovery of resistivity, internal friction, and shear modulus together with some hardening and relief of internal strains occurred before the visible growth of a textured substructure above 350°C (recrystallization in situ). The complex behavior of shear modulus, internal friction, and its strain amplitude dependence during annealing are discussed qualitatively in terms of the relative mobility of dislocations. BY plastically deforming fully recrystallized 99.98 pct Cr above the brittle to ductile transition temperature, at -350°C. as in wire drawing, chromium can be made very ductile at room temperature. However, this ductility is lost on annealing at high temperatures when recrystallization takes place.' The present investigation was made to determine the general pattern of the changes in a number of physical and mechanical properties during recovery and recrystallization of heavily deformed chromium as part of an effort to elucidate the reasons for lack of ductility in the fully recrystallized condition. PREPARATION OF MATERIAL Wire specimens 0.027 in. in diam were prepared from arc-melted, electrolytic chromium by extruding, hot swaging and finally wire drawing at 300" to 350°C, i.e. above the brittle-to-ductile transition temperature. The total reduction in area of the wire was 98 pct and the last 3 pct of reduction was made at 100" to 150°C before cooling to room temperature. The impurity content of the material is shown in Table I. Internal friction and modulus measurements were made on a single specimen after annealing in situ at successively higher temperatures. For all other measurements, a fresh specimen was used for each temperature and annealing of these specimens was done in evacuated (0.001 mm Hg) and sealed silica tubes for 1 hr at the various temperatures up to 700°C. EXPERIMENTAL METHODS AND RESULTS The occurrence of a. transition in some physical properties of chromium at - 40°C2 imposed limitations on the temperature region where some of the measurements could be made. The reason for this transition in chromium is at present unknown but is probably associated with an antiferromagnetic state observed below - 40°C.* Heavy deformation produces an anomalous decrease in resistivity when measured at temperatures below -40°C4 though a normal increase is observed above this temperature. On the other hand internal friction in heavily deformed chromium5 over the temperature range 40" to 50°C is invariant with temperature. Above and below this range internal friction is strongly temperature dependent, increasing with increasing temperature. A temperature in this range was therefore convenient for both resistivity and internal friction measurements and for consistency the measurements of the mechanical properties were also made at about this temperature. No structural change has, however, been observed in careful X-ray measurements6 between -195" and 50°C, i.e. departure from cubic symmetry was not greater than 3:10,000; X-ray line sharpening measurements were therefore more conveniently made at room temperature.

Jan 1, 1962

By B. M. Larsen, T. E. Brower

IN two previous papersl,2 dealing with the carbon-oxygen reaction, and the simultaneous content of each, in liquid steel in the furnace, we have made use of the quantity 0[O], defined as the excess oxygen beyond what would be in equilibrium with carbon then present if the pressure of carbon monoxide were I atm,; that is, if [C] X [O] is taken as 0.00222, 0[O] = [O] - 0,00222/[C] where [O] is the percentage of oxygen by weight as measured by the method described earlier.' This quantity 0[O] proves to be substantially independent of carbon content over the range 0.08 to 1.2 per cent, as well as of the basicity of the slag, and is nearly always within the limits 0.015 to 0.025 per cent when the bath is boiling normally and is in what we have termed a steady state. Apparently it must be at least about 0.014 per cent before boiling occurs; but this threshold value seems to depend upon the ease of bubble formation at the metal-hearth interface, hence upon the condition of the surface of the hearth. In any case, 0[O], on the average, changes considerably following any disturbance of the bath, as by addition of ore. The present paper deals with the average changes in ?[O] level following addition of Spiegel or crop ends, or after procedures to promote stirring, or by tapping of the steel from the furnace. The observations were made on a large number of commercial heats, and consequently are subject to the influence of various disturbing factors; the results have the compensating merit of showing the consistency obtainable under the limitations imposed by practical operation. VARIABILITY OF EXCESS OXYGEN IN NORMAL OPEN-HEARTH OPERATION The preceding general statements refer to the average value of ?[O] particularly in heats that are boiling actively; on individual heats, which are less active, there may be a variable time lag between the disturbance and its effect, which complicates the interpretation of what is going on. For instance, if in the normal refining process boiling is sluggish, the slag usually is gaining oxygen from the gas phase above it, or from added ore, faster than it is losing oxygen to the metal; yet when the bath starts to boil vigorously, the opposite condition may prevail for some time. The consequence of this lag is a variation of ?[O], the interpretation of which in a single heat may not be immediately obvious, This condition is illustrated in Figs. I and 2. In Fig, I, ?[O] at the beginning of the test period was near the lower limit of its usual range (dashed lines) in the steady state as a consequence of the lime boil, which had ended about as indicated. The bath is now cold, carbon drop is slow, and the first small ore feed causes only a small rise in 0[O]; as the temperature rises and as lime dissolves in the slag, and the bath becomes more active, the

Jan 1, 1946

By S. W. Churchill

A digital computer was used to obtain an exact numerical solution for the transient behavior of the insulation and earth adjacent to an isothermal, submerged flat surface for a single set of parametric values. Comparison of the computed results with analytical solutions for limiting conditions revealed that a complete and general solution for all parametric values could be constructed from these limiting solutions. Complete and general solutions for insulated spheres and cylinders can also be constructed from limiting solutions. The procedure is illustrated in part for an insulated spherical tank. The heat flow was found to fall rapidly to a pseudo-steady state; after some time, it then decreased slowly to zero for a flat plate and cylinder, and to a low steady-state rate for a sphere. The accumulative heat flow during the initial falling-rate period may be a significant fraction of the heat flow during the entire first year. INTRODUCTION Underground storage of liquefied natural gas and liquefied petroleum gas has received considerable recent attention. The rate of heat flow from the earth to the storage cavity and the resulting temperature field in the earth are important factors in the technical and economic evaluation of such storage facilities. The objective of this paper is to indicate how complete solutions can be developed for the transient flux and temperature field for various geometrical configurations. The representative properties and dimensions, and the resulting parameters utilized in the illustrative results, are indicated in Table 1. The results presented herein are for dry earth. The effect of the latent heat of solidification of water in the soiI will be described in a subsequent paper. The temperature field in the insulation and earth is determined by energy balances, boundary conditions and initial conditions. The physical problem can be described mathematically with virtually no idealizations insofar as physical properties are known. It appears possible to solve the equations by numerical integration on a high-speed digital computer for any geometrical configuration and conditions. For complex situations, however, the computations are expensive and the results are highly specific. Analytical solutions have been developed for a few simple but important geometrical configurations and conditions, including one-dimensional heat transfer from (or to) earth at an initially uniform temperature to (or from) flat plates, spheres and circular cylinders. The solution for an insulated flat plate has also been derived but is in the form of a slowly converging series involving taklated functions. It was planned to use a computing machine to evaluate this series for a number of representative conditions. However, upon examination of the results of preliminary computations it was discovered that a complete, general and accurate solution could be developed by interpolation between several much simpler solutions for limiting conditions. This technique then was used to develop a a complete solution for an insulated sphere. The equations presented herein are derived in Carslaw and Jaegerl and other books on applied mathematics, or they are simple extensions of these previous results. Hence, all derivations are omitted. Emphasis is instead placed on the results and their

By G. H. Lair, B. J. Langford, S. H. Rockwood

Volumetric reservoir analysis is dependent upon a firm relationship between porosity, connate water, and net pay. Capillary presswe data on core samples interrelate these three factors. It is shown that other reservoir problems may be resolved: (I) whether water production is indigenous or extraneous to the oil producing interval, (2) an oil-water contact is being approached, and (3) whether the oil-water contact is remotely situated. INTRODUCTION Volumetric analysis of carbonate reservoirs challenges the ingenuity of the reservoir engineer due to an absence of data on the minimum oil-bearing and oil-producing pores of a given reservoir rock. Many studies with this as the ultimate objective are available on the physical characteristics and fluid-flow behaviors of the carbonate reservoir. Some of these publications are: Hassler, Brunner and Deahl's1 study of the role of capillarity in oil production; Jan Law's' and A. C. Bulnes3 statistical treatment of core analysis data; Chalkley's method4,5 or estimating specific surface areas and porosity; Walter Rose's9 report on porosity, reserves, and recovery; Archie's78 tex-tural classification of carbonate rocks; Stewart and Spurlock's9 large core analysis; Purcell'sl0 mercury injection method in studying capillary pressure phenomena; Stewart, Craig, and Morse's" model multiple-phase flow test in investigating the relative permeability effect; and Fatt's12 illumi-nating network model of porous me-dia. The present study shows that the static reservoir parameters of porosity, connate water, and net productive thickness may be interrelated by utilizing a statistical arrangement of mercury capillary pressure data in addition to routine core analysis. This report summarizes the techniques that are followed to obtain these relations which are applicable to carbonate and sandstone reservoirs that do not contain clays. Capillary pressure statistical studies may be extended to include clay-bearing rocks by utilizing water capillary pressure data. POROSITY It is necessary that the laboratory determine the porosity value that includes the pores that are filled with hydrocarbons and water in the reservoir. This is the reservoir's total porosity. When true total porosity values are not available, correlations between porosity and capillary pressure characteristics lose their significance since they cannot be related through oil-base mud core data to the porosity and connate water values found in reservoirs. Methods used to obtain reliable porosity data will not be discussed; however, care should be exercised in selecting samples for measurement. In homogeneously porous formations, small core plugs sampled frequently will furnish adequate information. Where heterogeneity, particularly vugginess, is present, large-core porosity data may be required; in such reservoirs a suite of capillary pressure samples may be selected from small plugs. CAPILLARY PRESSURE Capillary pressure data provide a method for relating two carbonate reservoir parameters, porosity and connate water saturation, which in turn permit delineation of productive rock types necessary for selecting the third parameter, productive thickness. Specific applications of capillary pressure data to petroleum reservoirs were suggested by Archie8 and Pur-cell."' Their work demonstrated that in preferentially water-wet rock, porc

Jan 1, 1958

By B. M. Larsen, T. E. Brower

Introduction and Summary By "thermochemical factors" we refer to those variables which affect the net heat which must be put into the bath in order to make a heat of steel from any given set of charge materials. This is admittedly only one phase of the production rate problem. The whole problem includes also consideration of rate of charging, flame radiation intensity, rate of optimum fuel input obtainable without undue damage to the furnace structure and any variations in conditions such as stirring, slag volume or viscosity which affect the rate at which heat can flow down and away from those exposed surfaces where the heat is first received from the flame. Because a given type of charge in a shop is often considered as being nearly constant in both physical and chemical characteristics from one heat to another, and because such a state of affairs may be thought of as resulting in a reasonably constant net heat requirement, this requirement is usually neglected as an invariable, inevitable matter, about which nothing can be done. With normally variable charge, and variable percentages of limestone and cold pig, however, the net heat requirement can be subject to very appreciable change; it may also be affected by such things as the currently popular procedure of blowing oxygen into the bath. To bring the general problem of production rate into better perspective, therefore, it seems worthwhile to try to evaluate the net bath heat requirement and the amount by which it may change through variation in different factors. Because our calculated values of net heat are admittedly uncertain, we have tried to check them in part by statistical data on actual production rates over rather large groups of commercial heats. The results of calculation of net heat requirements in a wide range of actual commercial practices may first be summarized briefly. We find a wide range between the extremes of different practices, as would be expected, with duplex practice (essentially blown metal plus hot metal) having essentially a zero net heat requirement, an all-cold charge practice somewhat over I million Btu per ton of steel and a high hot metal practice about 0.75 million Btu per ton. Over the commercial range of scrap plus hot metal practice, increasing the percentage of hot metal from 40 to 78 pct, with other factors nearly constant, decreased the net heat by only some 5-10 pct. The net heat is increased by about 1.2 pct for each I pct of the metallic charge present as cold pig. Calculated values of oxygen supplied by air varied from about 25 up to 60 lb per ton of steel, and in a 60 pct hot metal practice, an increase from 32 to 52 Ib oxygen from air decreased the calculated net heat from 0.88 to 0.74 million Btu per ton. Use of pure cold oxygen to substitute for about one half of the total charge ore (about 28 Ib oxygen replacing 145 Ib ore per ton of steel) decreased the

Jan 1, 1949

By B. M. Larsen, T. E. Brower

Introduction and Summary By "thermochemical factors" we refer to those variables which affect the net heat which must be put into the bath in order to make a heat of steel from any given set of charge materials. This is admittedly only one phase of the production rate problem. The whole problem includes also consideration of rate of charging, flame radiation intensity, rate of optimum fuel input obtainable without undue damage to the furnace structure and any variations in conditions such as stirring, slag volume or viscosity which affect the rate at which heat can flow down and away from those exposed surfaces where the heat is first received from the flame. Because a given type of charge in a shop is often considered as being nearly constant in both physical and chemical characteristics from one heat to another, and because such a state of affairs may be thought of as resulting in a reasonably constant net heat requirement, this requirement is usually neglected as an invariable, inevitable matter, about which nothing can be done. With normally variable charge, and variable percentages of limestone and cold pig, however, the net heat requirement can be subject to very appreciable change; it may also be affected by such things as the currently popular procedure of blowing oxygen into the bath. To bring the general problem of production rate into better perspective, therefore, it seems worthwhile to try to evaluate the net bath heat requirement and the amount by which it may change through variation in different factors. Because our calculated values of net heat are admittedly uncertain, we have tried to check them in part by statistical data on actual production rates over rather large groups of commercial heats. The results of calculation of net heat requirements in a wide range of actual commercial practices may first be summarized briefly. We find a wide range between the extremes of different practices, as would be expected, with duplex practice (essentially blown metal plus hot metal) having essentially a zero net heat requirement, an all-cold charge practice somewhat over I million Btu per ton of steel and a high hot metal practice about 0.75 million Btu per ton. Over the commercial range of scrap plus hot metal practice, increasing the percentage of hot metal from 40 to 78 pct, with other factors nearly constant, decreased the net heat by only some 5-10 pct. The net heat is increased by about 1.2 pct for each I pct of the metallic charge present as cold pig. Calculated values of oxygen supplied by air varied from about 25 up to 60 lb per ton of steel, and in a 60 pct hot metal practice, an increase from 32 to 52 Ib oxygen from air decreased the calculated net heat from 0.88 to 0.74 million Btu per ton. Use of pure cold oxygen to substitute for about one half of the total charge ore (about 28 Ib oxygen replacing 145 Ib ore per ton of steel) decreased the

Jan 1, 1949

By Irving Fatt, Robert J. S. Brown

INTRODUCTION The wettability of reservoir rocks is recognized as one of the major factors that determines their multiphase flow properties. Multiphase flow properties in turn govern reservoir performance. For this reason, the reservoir engineer is vitally interested in the wettability of reservoir rock. The production research scientist is interested in wettability because the solution of the problem of improving waterflood recovery by use of surface-active additives may hinge on a detailed understanding of the wettability of reservoir rock. Early workers believed that all reservoir rocks were preferentially water wet. Continued study soon uncovered certain rocks which had flow properties that indicated that they were preferentially oil wet. Recent studies show that there is a spectrum of wettability. Some reservoir rocks have multiphase flow properties which indicate that they have an intermediate wettability. The differences in recovery observed among different reservoirs may, in part be the result of small differences in wettability. Differences in wettability amcng reservoir rocks may be the result of differences in the fraction of the total surface area that is preferentially oil wet and preferentially water wet. Nuclear magnetic relaxation measurements may provide a method for determining the fraction of preferentially oil wet and preferentially water wet area in porous media. Measurements to be reported here were made on water-saturated unconsolidated sand packs which were mixtures of preferentially oil wet and preferentially water wet sands. The resulting data show definitely that the fraction of each wettability in these sand packs can be determined by this nondestructive method of measurement. THEORY OF NUCLEAR MAGNETIC RELAXATION The details of the theory of nuclear magnetic relaxation have been presented previously1. In this paper, only a very brief review of the theory will be given to show its application to the measurement of fractional wettability. Nuclear magnetic relaxation is a process of adjustment undergone by certain atomic nuclei when their magnetic environment is changed. They adjust, or relax, to be in equilibrium with a new magnetic field. The reason that some atomic nuclei are affected by a magnetic field is that they themselves behave in some respects like tiny magnets. In particular the proton, the nucleus of the hydrogen atom, behaves as a magnet. The proton spins, somewhat as the earth spins on its axis. The spinning charge produces a magnetic field just as current traveling in a loop of wire produces a magnetic field. No net charge is required, however; for instance, the neutron has spin and magnetic moment. When the spinning proton is subjected to an externally applied magnetic field, its axis tends to line up with the magnetic field, somewhat as a compass needle tends to line up, but the spinning proton cannot do this as easily as the needle can. The proton also has mass, and its spinning mass makes the proton behave somewhat like a gyroscope. As is well known, a force which tends to change the axial direction of a gyroscope merely causes the gyroscope to precess: lhat is, the axis begins to trace out a conical surface. The gyroscope cannot actually assume the position suggested

Jan 1, 1957

By L. Himmel, R. F. Mehl, C. E. Birchenall

The rates of self-diffusion of iron in artifically prepared wustites of various compositions have been determined using the decrease in surface activity technique. Similar measurements are reported for artificial magnetites of nearly stoichiometric composition and for natural hematite single crystals. These data, together with appropriate thermodynamic data derived from the present study or from the literature, are used to calculate the rates of oxidation of iron and its oxides, taking as a basis the theoretical rate equations developed by Wagner. The calculations are compared with experimental rate constant data for these same reactions and are shown to provide essential confirmation for the Wagner theory. For the most part, the results are also consistent with the previously proposed transport mechanisms in the oxides of iron. WHEN a metal is exposed to an oxidizing atmosphere at elevated temperatures, a superficial oxide layer is formed which then thickens according to some characteristic rate law. Provided that the oxide layer is dense and continuous and does not present any paths for gaseous diffusion, continued growth must inevitably involve the migration of the reactants—either the metal or oxygen or both—through the lattice of the solid oxide. This is true whether the reaction rate is controlled by the diffusion process itself or by a slow step in a reaction at one of the interfaces. If the overall rate is limited by diffusion, and if the concentrations or thermodynamic activities of the reactants at the boundaries of the oxide layer are independent of time, the familiar parabolic rate law is observed. Under these conditions, Wagner1 has shown that the rate constant may be expressed in terms of the mobilities of the reacting components and the appropriate concentration or activity gradients which are established across the growing oxide layer. In presenting the phenomenological basis for the theory, Wagner has emphasized the role played by lattice defects in diffusion processes in oxides. The essential validity of this theory has been confirmed by experiment for a number of simple systems including the growth of Cu2O on copper.'-' One of the objectives of the present study has been to extend the Wagner approach to the more complex process of the oxidation of iron and its oxides, and particularly to wustite, which is normally the major constituent of the oxide scales formed on iron at temperatures above approximately 570°C. For this purpose the rates of self-diffusion of iron in w?stite, magnetite, and hematite have been measured by tracer techniques and the necessary thermodynamic data have been obtained from equilibrium studies involving the oxides and their atmospheres. These data have subsequently been used to test the underlying assumptions of the Wagner theory as well as the detailed mechanism of the scaling of iron previously proposed by Davies, Simnad, and Birchenall.5 Lengthy treatments of diffusion and conduction phenomena in ionic crystals have been published." * The latest, by Jost,8 also summarizes much of the existing experimental data. In general, however, the oxides of iron have not been considered specifically and hence a brief review of the available

Jan 1, 1954

By Kefton H. Teague

Attempts to locate domestic supplies of sillimanite have been unsuccessful until recently. This paper describes recent discoveries of sil-limonite-bearing schists in the Southeastern States, with emphasis on geology of the deposits, mineral composition, origin, and reserves. Statements concerning possible methods of mining, milling, and utilization of sillimanite are given. Results from refractory tests on a laboratory scale are summarized. SINCE 1917, when synthetic mullite was first used in spark plug porcelains, there has been a continued search for natural sillimanite. During the recent war this search was intensified, not only for sillimanite but also for any materials which could be used satisfactorily as a substitute for the imported kyanite from India. The Indian massive kya-nite does not decrepitate during calcination as does our domestic bladed kyanite, thus a coarse grog can be obtained from it. Some of the most promising domestic materials suited for high temperatures are limited in quantity. Massive topaz from Chesterfield County, S. C., showed promise of possessing desirable refractory properties; but the action of combined fluorine, liberated during calcination, upon equipment and surroundings, as well as a limited supply of ore and the presence of impurities discouraged its use. Residual lumps and boulders of massive kyanite, similar to the material imported from India, occur in Georgia. This material, like the massive topaz, is of limited quantity. Andalusite from California and dumortierite from Nevada are satisfactory high-temperature refractory materials. Their uses have been restricted to specialized products since the location and character of the deposits are such that large production is impractical. Sillimanite, like kyanite and andalusite, has the theoretical chemical composition of Al2SiO5. It has a hardness of 6 to 7; vitreous, silky to subadamantine luster; specific gravity of 3.2 to 3.3; and is gray to bluish gray in color. Under the binocular microscope, the crystals are transparent. The mineral may occur as dense, fibrous mats (fibrolite) composed of fibrous, sometimes radiating hair-like crystals in schist which are associated with igneous intrusions. Deposits of this type have widespread distribution, but none discovered to date appears to have commercial possibilities. Sillimanite also occurs as bundles of crystals disseminated in biotite schist, as noted in the Hart-Elbert-Madison County, Ga., area and in some of the South Carolina and North Carolina deposits. This type of material has been called prismatic sillimanite by the U. S. Bureau of Mines. Deposits of this variety appear to offer commercial possibilities. When heated above 1650°C, sillimanite expands about 6.5 pct and is converted into a mixture of mullite (3Al2O3 . SiO2) and vitreous silica. This is a stable mixture which has a specific gravity of about 3.15. General Geology: Sillimanite (fibrolite) is a mineral common to the pre-Cambrian metasedi-ments of the Southeast. It occurs throughout the crystalline schists which lie between the Fall Line on the southeast and the established Paleozoic rocks on the northwest (fig. 1). In addition to the meta-sediments, this area contains pre-Cambrian igneous

Jan 1, 1951

By Kefton H. Teague

Attempts to locate domestic supplies of sillimanite have been unsuccessful until recently. This paper describes recent discoveries of sil-limonite-bearing schists in the Southeastern States, with emphasis on geology of the deposits, mineral composition, origin, and reserves. Statements concerning possible methods of mining, milling, and utilization of sillimanite are given. Results from refractory tests on a laboratory scale are summarized. SINCE 1917, when synthetic mullite was first used in spark plug porcelains, there has been a continued search for natural sillimanite. During the recent war this search was intensified, not only for sillimanite but also for any materials which could be used satisfactorily as a substitute for the imported kyanite from India. The Indian massive kya-nite does not decrepitate during calcination as does our domestic bladed kyanite, thus a coarse grog can be obtained from it. Some of the most promising domestic materials suited for high temperatures are limited in quantity. Massive topaz from Chesterfield County, S. C., showed promise of possessing desirable refractory properties; but the action of combined fluorine, liberated during calcination, upon equipment and surroundings, as well as a limited supply of ore and the presence of impurities discouraged its use. Residual lumps and boulders of massive kyanite, similar to the material imported from India, occur in Georgia. This material, like the massive topaz, is of limited quantity. Andalusite from California and dumortierite from Nevada are satisfactory high-temperature refractory materials. Their uses have been restricted to specialized products since the location and character of the deposits are such that large production is impractical. Sillimanite, like kyanite and andalusite, has the theoretical chemical composition of Al2SiO5. It has a hardness of 6 to 7; vitreous, silky to subadamantine luster; specific gravity of 3.2 to 3.3; and is gray to bluish gray in color. Under the binocular microscope, the crystals are transparent. The mineral may occur as dense, fibrous mats (fibrolite) composed of fibrous, sometimes radiating hair-like crystals in schist which are associated with igneous intrusions. Deposits of this type have widespread distribution, but none discovered to date appears to have commercial possibilities. Sillimanite also occurs as bundles of crystals disseminated in biotite schist, as noted in the Hart-Elbert-Madison County, Ga., area and in some of the South Carolina and North Carolina deposits. This type of material has been called prismatic sillimanite by the U. S. Bureau of Mines. Deposits of this variety appear to offer commercial possibilities. When heated above 1650°C, sillimanite expands about 6.5 pct and is converted into a mixture of mullite (3Al2O3 . SiO2) and vitreous silica. This is a stable mixture which has a specific gravity of about 3.15. General Geology: Sillimanite (fibrolite) is a mineral common to the pre-Cambrian metasedi-ments of the Southeast. It occurs throughout the crystalline schists which lie between the Fall Line on the southeast and the established Paleozoic rocks on the northwest (fig. 1). In addition to the meta-sediments, this area contains pre-Cambrian igneous

Jan 1, 1951

By R. C. Rumble

To /neet the need for a subsurface flowmeter capable of measuring low rates of flow, a new type flowmeter has been built and tested in the field. This instrument is self-contairzed, can be run on a wire measuritzg line, and may be run through 2-in tubing. It consists of a rotameter flow-measuring assembly used in conjuncfion with a conventional subsurface instrument clock and chart. Integral with the tool is an inflatable packer which, by effecting a seal between casing and tool, diverts all fluid through the metering assembly. Packers of different size adapt the tool to different sizes of casing or liner. The flowmeter is capable of measuring rates of flow as low as 4 BID. The flowmeter has been run experimentally in seven wells. It has yielded satisfactory resrrlts in five of the wells, and in the other two it failed to operate because of loose sand in the hole. INTRODUCTION One of the oldest problems facing the producing branch of the petroleum industry is the location of depths of entry of fluid into a wellbore and the determination of the amount of fluid entering at each depth. This problem is often encountered in oil and gas wells completed in single producing horizons as well as in multiple pays; it is a common problem in oil wells which produce excessive volumes of gas. Several subsurface instruments designed to detect and meter flow in the producing interval of wells have been described in the literature.1,2,3,4 Most of these, however, were apparently intended for use in wells producing at relatively high rates of flow, and consequently lack sensitivity to low flow rates. Because of this and of other possible disadvantages inherent in these instruments, development of the subsurface flowmeter described in this report was undertaken. DESIGN OF FLOWME'I'ER Design Requirements In considering the requirements for a flowmeter that would not be subject to the limitations of devices existing at the time work was started, attention was first given to the size of the tool. Such an instrument should be of sufficiently small diameter that it could be lowered readily in 2-in tubing in a producing well. The flowmeter should contain a recording unit so that it might be run on a wire measuring line with conventional reeling equipment. It should not be too long to be accommodated by a portable lubricator of the type used for running conventional subsurface instruments. The metering mechanism of the flowmeter should not be affected appreciably by the viscosity or density of the flowing fluid. Such an instrument should record flow rates in the range from less than 10 B/D to over 100 B/D. To achieve this, a packer should he provided to divert through the instrument all fluid flow in the wellbore. This packer should be of such nature that in the event of excessive flow the fluid would bypass the instrument instead of forcing it up the wellhore. General Description A flowmeter incorporating most of the desired features outlined above was developed and built. The instrument is an elongated tubular device terminated on

Jan 1, 1956

By Franz Fohr

On July 27, 1919, there passed away a simple, unassuming gentle-man, who, throughout his life, allowed his intense modesty to keep him-self in the background and during his later years effaced himself so thoroughly that but few of his acquaintances knew aught of him. Yet he was one of our accomplished metallurgists, who did good work in the practice of his profession and lived an upright life. Now that he is no longer with us Franz Fohr cannot plead to be overlooked, and those who fondly remember him will be gratified by his receiving his due. Franz Fohr was born, Sept. 7, 1838, in Mannheim, Germany. Of his ancestry, education, and early career we know scarcely anything. We do not even know just when he came to America, or. what led him hither. The first record of his professional work in this country, found among his papers, shows that from July, 1870, to Jan. 1, 1872, he was superin-tendent of the Newark Smelting & Refining Works, then owned by Ed-ward Balbach & Son. At that time the Balbach works at Newark, established in 1850, and the Selby works at San Francisco, established about 1866, were the only important silver-lead refineries in the United States. Mr. Fohr may have been associated with the Balbachs for some time before he became superintendent of their plant or he may have come from Germany but a short time previously. At all events, it is certain that he was at that time an experienced and accomplished metallurgist. After leaving Newark and going to San Francisco, he soon formed a connection with Thomas H. Selby & Co. Early in 1874-this firm sent him to New York to procure information respecting the manufacture of white lead. His engagement in New York terminated on-Jan. 31, 1875. During 1875, Mr Fohr spent some time at Silver Islet and in the Lake Superior copper region, but of his work there no record remains. In the latter part of 1875, or early in 1876, he associated himself as metallur-gist with the Boston Silver Co., operating at Saint John's, Summit County, in which William L. Candler, of Boston, was the moving spirit. That company was developing its mine in 1875. At the end of that year it "had about 800 tons of ore on hand, about three-fourths of which is dress-ing ore, to be concentrated in its very systematic establishment and to be smelted into pig lead." Evidently Mr. Fohr was engaged for the latter purpose. Henry A. Vezin, erudite and painstaking, was the mechanical engineer for the company. In the fall of 1876, Anton Eilers took his family for the first time so far West as Denver and Mr. Fohr went with them. I do not think that Mr. Eilers had any connection with the Boston Silver Co., save possibly in a consulting capacity, but he visited Saint John's and the enduring friendship among Eilers, Fohr, and Vezin, which terminated only with their deaths, dated from that time.

Jan 12, 1919

By A. K. Snelgrove

This symposium is designed to marshal a state-of-the-art account of approaches and solutions to problems arising out of waterlogging and salinization in the world's largest irrigation system which was dismembered by legal beheading of the Eastern Rivers under the lndus Waters Treaty of 1960. In this introduction, the geological and historical backgrounds of surface waters and groundwaters in the Indus Basin are presented with a summary of remedial measures undertaken and proposed to combat waterlogging and salinization. At a time when water-resource planning is proceeding on a continental scale, a study devoted solely to the Indus River Basin may seem to require an apologia. None is offered, however, for three major reasons: (1) Although the Indus is a single river basin, it is one of great magnitude and importance. The Indus River, which comes from Himalayan sources to form part of the great Indo-Gangetic Plain drainage system, is vital to agriculture and hydroelectric power in the thickly populated northern subcontinent of Indo-Pakistan. (2) The Indus has become a plexus of extraordinary problems since the dismemberment of the world's largest irrigation system of which it was a part. The break-up of this system occurred with the legal beheading of the Eastern Waters under the Indus Waters Treaty of 1960. (3) Th River Basin has been the target of a Herculean effort to contain the twin encroachments of waterlogging and salinization that now threaten it with a shortage of fresh water. The British irrigation system of barrages and canal on the Indus was a venture admirable in conception. Unfortunately, it is now a legacy burdened with unwanted consequences due to interference with the hydrological regimen, particularly the rise of water table occasioned by leakage. To cope with this situation, there has been a possibly unprecedented concentration of domestic and international engineering and scientific talent on the Indus and its problems (about a score of organizations by recent count). To marshal a state-of-the-art account of their approaches and solutions is the purpose of this Symposium. The coordinated effort now being made on a variety of fronts under the general supervision of West Pakistan Water and Power Authority (WAPDA) is directed toward the modification and control of interactions and relationships between geological materials — soils, water and its salt balance, and air —in what has been termed a huge "underground lake" in an alluvial basin. The problem is an intriguing one in that a highly complicated case history of river-course changes visible in the present surface must be projected downwards through Recent and Pleistocene sediments in order to decipher the environmental controls of deposition in terms of vertical and lateral variations in lithology and patterns. Such studies must be extended to compaction, deformation, and fabrics of the alluvium. Geohydrology is often defined as groundwater hydrology. As employed herein, it includes the distribution, quality, and behavior of surface and subsurface waters, including their evolution, vagaries, and geological, climatological, and botanical milieux." GEOGRAPHY The Indus (Sanskrit, Sindhu = river) rises at nearly 17,000 ft above the sea in the glaciers on the northern slopes of Kailas Parbat, Tibet. It is about 1800 miles long and has a total drainage area estimated at 372,000 sq miles. The average discharge is 196,000 cfs at mouth. Leaving the Plateau of Tibet, the river flows at a level which is miles above the sea, and in places miles below Himalayan peaks, in a structurally controlled northwestward course. Joined in this course by six tributaries and swollen by the melt waters of giant glaciers, it swirls about the base of the famous

Jan 1, 1970

By H. C. Chang, N. J. Grant

Creep of very coarse grained, high purity aluminum was studied at 400° to 1100°F with an initial stress range of 50 to 1200 psi. The process of boundary sliding and migration was studied. The driving force of boundary migration under creep conditions is shown to be a combination of strain energy migrationand surface energy. A theory is presented regarding the strainenergyrole the grain boundaries play under creep conditions. From this thetheory intercrystalline failure of commercial alloys can be explained. Also from this theory an optimum grain size should exist for good high temperature properties of high purity materials. IN the investigation of the creep of very coarse grained, high purity aluminum previously reported,' the cyclic nature of the process of grain boundary sliding and migration has been established by microscopic observation of the actual creep process as well as metallographically. It was also substantiated by measuring localized strains across the grain boundaries. In addition, it was shown how extensive subgrain and fold formation may result from boundary sliding and how the slid grain boundary may become sharply wavy as a result of subgrain formation. Since the publication of those results, additional information on the process of grain boundary sliding and migration has been obtained. It is the purpose of this paper to report on the direction and driving force of boundary sliding and migration, the effect of grain size, and the effect of temperature. Finally the effect of decreasing purity (alloys 2s and 3s) on the process of boundary sliding and migration is noted. From these results, an explanation is presented for the intercrystalline failure of alloys under creep conditions. The effects of grain size on the creep properties of impure and high purity materials are discussed in the same light. The experimental procedures and technique have been presented elsewhere.' It is only necessary to state how the 2s and 3s aluminum specimens are prepared. Machined specimens were first annealed at 600°F for about 12 hr. In order to produce a large grain size the specimens were then stretched 3 to 8 pct. The specimens were marked with reference marks, electropolished, annealed at 900°F for 24 hr and at 1150°F for 12 hr, and repolished. The grain size of 2s aluminum produced by this treatment is comparable to that of high purity aluminum in the direction of its width of the specimen, i.e., there are 2 to 4 grains across the width of the specimen. However, the grains of 2s aluminum are 3 to 10 times longer in the direction of the specimen axis. On the other hand, the grain size of coarse grained 3s aluminum ranges from 10 to 20 grains across the width of the specimen due to the treatment just outlined and therefore is much smaller than that of both high purity and 2s aluminum. As in 2s aluminum, the grains are about 3 to 10 times longer in the direction of the specimen axis than in the direction of the width of the specimen. The arrangements of the grains in 2s and 3s aluminum were generally irregular; therefore it was difficult to follow the course of the grain boundaries. Results Method of Presentation: In order to show the arrangement of the grains, especially the direction and positions of the grain boundaries, traces of the grain boundaries on the four surfaces of the specimens were unfolded and mapped out after macroetching. Figs. 1 and 2 show the structural development drawings of specimens P-3 and P-8 respectively. The two flat surfaces (of which the front one faces the microscope) and the round-edged surfaces will be called the "front surface" and "back surface" and

Jan 1, 1954

By J. A. Herbst, D. W. Fuerstenau

This paper examines the zero order production phenomenon in the context of the size discretized batch grinding model. A restrictive interrelationship between the selection and breakage parameters of the model, which is mathematically sufficient to ensure zero order behavior, is delineated. Based on this interrelationship, a scheme is developed for predicting the values of the selection and breakage parameters for all size fractions from a minimum of experimental data. To test this scheme, dolomite was ground in a laboratory batch ball mill. Successful simulation of the comminution behavior of this system was achieved using the batch grinding model with the parameter values obtained from the proposed scheme. Historically, a preponderance of comminution research has centered on attempts to relate breakage energy to the performance of comminution machines. Concomitantly, grinding data were interpreted almost exclusively in terms of inherently empirical energy-size reduction relationships1-3 or "laws of comminution"4- 6 which were based on highly oversimplified descriptions of the fracture process. In some instances, these relationships provide a crude basis for the correlation of experimental data, but, invariably, this approach is inadequate for meaningful process simulation. The control and optimum design of comminution circuits require a mathematical model capable of depicting the size reduction behavior of every size fraction for grinding conditions of technological importance. Energy-size relationships do not provide this detailed information. For example, an energy-size analysis for batch ball-milled dolomite has recently been completed in the authors' laboratories.7 This analysis provided a satisfactory correlation between the hypothetical size modulus, which characterizes only the finer portion of the size distribution, and the input energy. However, this relation did not constitute an adequate description of the complete system. In general, one of two distinct viewpoints toward simulation has been adopted in recent comminution research. The first approach focuses on the fracture of single mineral specimens, with the essential aim of representing the over-all process in terms of the breakage characteristics of individual particles and the characteristics of the stress field which the particles experience within the particular size reduction device. As illustrated by Harris's review,' the actual incorporation of single-specimen fracture information into a description of the behavior of a multiparticle comminution system has seldom been attempted. The only model to accomplish this incorporation was the one developed by Schönert.8 The Schonert model treats single-passage grinding machines in terms of a distribution of effective loads acting on a particle, a distribution of required particle breakage energies, and the breakage product distribution. However, the use of single-particle fracture behavior to derive models of the size reduction process is at present limited to machines in which the particle residence time is approximately equal to the time required to apply stress. As a result, Schönert's analysis cannot be used to advantage to simulate the complex environment which prevails within a tumbling mill. For multiple-passage systems a second approach to the description of comminution processes has been more fruitful. This approach entails the formulation of a mathematical model which is phenomenological in nature in that it lumps together the entire spectrum of stress-application events which prevail in a system under a given set of operating conditions. The appropriately defined average of these individual events is then considered to characterize the over-all breakage properties of the device. Thus, to analyze the performance of a tumbling mill, the manner in which the particles of a particular size (or size fraction) are stressed need not be distinguished. Instead, a single parameter is assumed to represent the resistance of that size to fracture, given the average grinding environment which exists in the mill. The isolation of such a parameter and a related set of quantities, which constitute the breakage product size distribution for the average event in this size fraction, allows the formulation of physically meaningful descriptive equations capable of yielding precise and detailed information for simulation.

Jan 1, 1969

By F. C. Bond

Since the Third Theory of Comminution was presented eight years ago (I) it has found increasing use in crushing and grinding problems. The practical utility of its wok index equation is quite generally acknowledged (2). However, its theoretical basis has been questioned in at least three technical articles (3) (4) ('). The purpose of this paper is to present experimental proof that it is scientifically correct. Particles under compressive stress are strained and deformed. They absorb strain energy, and when this locally exceeds the breaking strength, a crack tip forms. The surrounding strain energy flows to the crack tip, which rapidly extends and splits the rock, releasing the strain energy as heat. The initial energy flow causes additional crack tips in highly strained areas. If the compression is rapidly applied by impact, crack tips may form before the strain energy has reached equilibrium in the particle, thus decreasing the total work input required for breakage. The energy necessary to break is essentially the energy necessary to produce crack tips, since the energy necessary to extend the cracks to breakage is already present as strain energy in the deformed particles. After breakage nearly all of this energy appears as heat. The crack length cannot be measured directly. However, in particles of regular and similar shape the crack tip length is considered as equal to the crack depth, or crack extension necessary to break, so that the crack length equals the square root of one-half of the surface area. The Third Theory states that the useful work done in crushing and grinding is directly proportional to the total length of the new cracks formed. It can be confirmed by showing that a constant work input produces a constant length of new cracks when reducing the same material to different product sizes. This is done in the present paper on a wide variety of material. The constant work input was supplied by one revolution of the 12" x 12" laboratory ball mill used in making grindability tests by the Allis-Chalmers method (12) (13) The new crack lengths produced per mill revolution were measured from all available grindability test results at 28, 35, 48, 65, and 100 mesh on fifteen different ores, and were found to remain substantially constant for each ore at all mesh sizes. A new technique is used for the measurement of crack lengths. Size distribution plots of the mill feed and product are made by the Third Theory method (9) and the crack lengths are obtained from these plots by the procedure described in the present paper. The energy input required to produce a unit length is of fundamental importance in the size reduction of brittle solids. The crack length Cr is expressed in centimeters per cubic centimeter of solid material. It bears a definite relationship to the external surface area of the crushed or ground solid. A uniform particle shape must be assumed before the surface area and crack length can be evaluated. In this paper it is assumed that the relationship between the surface area and the particle volume of a particle d microns in diameter is the same as that of cube d microns on a side. The external surface areas of particles with a cubical breakage probably agree approximately with this rule, and correction factors can be applied when physical measurements of the surface areas are available for comparison. However, the assumption of equivalent cubes has been found satisfactory for most calculation purposes. Assuming equivalent cubes, one cubic centimeter of particles d microns in diameter will have a crack length Cr of v30.000/d centimeters, and a surface area of 60,000/d square centimeters. The specific crack length is thus equal to the square root of one-half the specific surface area. Where Sa is the surface area in square centimeters per gram and Sg is the specific gravity of the ground solid, then Cr = vSg . Sa/2 = 173.2/ vd (1)

Jan 1, 1961

By G. W. Doepel, W. P. Sibley

A three-dimensional, multilayer, mathematical model has been developed for predicting performance by mis-c.ible displacement. Areal and vertical coverage, total gas-oil ratio, propane-oil ratio and oil-recovery factor for the multilayer system are computed as functions of hydrocarbon pore volumes of solvent injected. The technique has been programed for use on the IBM-7090 digital computer and was used in calculating perfortnance for continuous miscible displacement of a five-spot, 50-layer .system. Results reported are based on the use of published laboratory data for a single, uniform five-spot layer. However, the technique is sufficiently generalized to calculate performance of any system of layers of any pattern configuration and mobility ratio, provided data are available to describe perfortilance of a single layer. The technique has also been adapted for predicting oil recovery resulting from various gas-driven slug sizes. The results presented for both continuous and slug-type injection show, that permeability variation has 0 significant effect on oil recovery but that solvent composition, within the range studied, has a lesser effect on oil recovery. INTRODUCTION Experience from many of the miscible-phase displacement projects currently in operation indicates that the injected solvent flows preferentially through the more permeable zones in the reservoir. This preferential solvent flow in the high-permeability streaks results in a reduction of vertical coverage (C,) and an attendant decrease in oil recovery. The multilayer technique presented in this paper uses areal coverage (C.,) data for a single layer from the literature and from laboratory measurements of displacement efficiency (herein referred to as microscopic coverage, C,,) to calculate areal coverage (C,) and vertical coverage (C,) for the multilayer system. Oil recovery for the multilayer system is obtained as the product of (Ca) (Cm) (Cv). It is assumed that C, in a single layer is 100 per cent; therefore, (C,) (Cm) is a measure of oil recovery from that layer. Data presented in the literature for a single layer generally deal only with areal coverage and/or microscopic coverage —but seldom specifically with oil recovery. Nevertheless, this technique is flexible in that either Ca and C,, of an individual layer or a direct measurement of oil recovery for the layer may be used. In developing this technique, the problem arose concerning a method of determining the relative amounts of solvent that will enter each layer during any increment of solvent injected. To solve the problem, a dimensionless equation was derived for expressing solvent injected into each layer as a fraction of total injection. A finite-difference method was applied in integrating the equation to determine oil recovery for the system of layers as a function of pore volumes injected. The technique subsequently was programed for solution on a digital computer. The method was applied to predict performance of a deep California reservoir under continuous miscible displacement and has been extended for calculating oil recovery as a function of slug size for gas-driven slug injection. The technique may be applied to any petroleum reservoir that can be adequately represented as a layered system, by considering permeability variation,1-3 permeability range and average permeability. Each layer is then assigned its appropriate permeability, porosity and hydrocarbon saturation. RESERVOIR VOLUME CONTACTED BY SOLVENT It has been recognized for some time that high microscopic coverage (C,) can be obtained by injecting a miscible agent, such as propane, into an oil reservoir. These high values of C,,, have been demonstrated in the laboratory and are normally between 80 and 100 per cent, depending on solvent and reservoir oil composition as well as on reservoir temperature and pressure. In miscible-phase displacement, because there is no interface between solvent and oil, effective permeability to solvent is the same as that to oil. (This assumes that oil saturation has not changed and that water is immobile.) Consequently, mobility ratio (M) simply reduces to that of viscosity ratio . Perrine4 and Habermann5 have shown that large