Search Documents

By M. E. Wadsworth, K. J. Richards

The oxidation rates of tantalum in various partial pressures of carbon dioxide in the temperature range 700°to 950°C were measured with a thermo-gravimetric balance. Oxidation involved a surface -controlled reaction associated with the formation of a nonprotective layer of Ta2O5. Below about 720°C, there was a change in the rate-determining mechanism, and above 830°C the linear rate was preceded by a complex region of nonlinear oxidation behavior. The linear oxidation of tantalum has been explained quantitatively in terms of carbon dioxide adsorption, followed by a rate-controlling surface reaction. The initial adsorption has been expressed both as an equilibrium process and as a steady-state reaction. The enthalpy for chemisorption of CO, was determined to be -17.3 kcal per mole. The surface-controlled reaction had an activation enthalpy of 40.4 kcal per mole. A considerable amount of interest has been shown in recent years in the oxidation of tantalum and the nature of the oxide film produced. This interest is associated with the increasing demand in our technology for structural materials to withstand high temperatures and corrosive atmospheres. The low oxidation resistance of tantalum has severely restricted its application as a high-strength, high-temperature material. As a fundamental approach to the realization of the full poten- tials of this metal, the kinetics of the oxidation of tantalum in oxygen and air have been extensively studied; however, very little work has been reported on the effect of other gases, including carbon dioxide. According to Miller,' the only reported study of the reaction between tantalum and dry carbon dioxide is a restricted observation by O'Driscoll et al.2 at 8 atm absolute pressure and 500°C. Therefore, this study was made to investigate the reaction of tantalum with carbon dioxide. EXPERIMENTAL MATERIALS AND METHODS The vacuum-annealed tantalum used in this study was obtained from Fansteel Metallurgical Corp. as 0.025-mm-thick sheet stock. This material had less than 0.1 pct total impurities, and the maximum individual impurity concentrations were

Jan 1, 1964

By T. F. Bower, M. C. Flemings

The classical explanation for formation of the fine equiaxed "chill zone " in ingot solidification is that local supercooling near the chill wall causes copious nucleation in this region. This work indicates, however, that convection is an essential element in formation of the chill zone. In the absence of convection, no chill zone forms even though rate of. heat extraction is extremely vapid. Alloy studied was Al-l.5 pct Cu alloy solidified against a copper chill wall. When solidification was initiated at the chill wall in absence of. cor-vection, surface grain size was large (>I cm diam). When it was initiated in the presence of convection, it was fine (<0.05 cm diam). It is concluded that some form of "crystal multiplication" plays an important role in formation of the chill zone. INGOT macrostructures are generally classed as containing one or more of the three zones: "chill zone", "columnar zone", and central "equiaxed zone". These three zones are sketched in Fig. 1; their origin has been discussed in some detail.&apos;-&apos; The classical explanation for formation of the chill zone is that supercooling occurs in the region of liquid metal adjacent the mold wall, and copious nu-cleation then takes place in this region forming numerous small crystals. The columnar region then results by growth of favorably oriented grains (den-drites) which crowd out their less favorably oriented neighbors."5 The mechanism of the columnar-equiaxed transition has been the subject of considerable interest. The generally accepted mechanism, until recently, was that constitutional supercooling developed in front of the growing columnar grains with eventual nucleation of new, equiaxed, grains ahead of the growing solid front.&apos; Recently, it became evident this explanation was not completely satisfactory and it is now evident that "crystal multiplication" plays an important role. This crystal multiplication occurs by separation of dendrite arms from growing dendrites,8?"&apos; and has been shown to be strongly influenced by convection.6, 10-13 Reduced convection results, for a given alloy, in longer columnar zone, larger columnar grains, and larger equiaxed grains.7, 12

Jan 1, 1968

By B. Woyski

Many writers, in discussing defects caused by oxidation and gassing of bronzes and red brasses advocate substantially the same cure for both. But from its nature, oxidation cannot take place if there is an excess of fuel in the furnace, while the gases absorbed by some alloys are products of incomplete combustion of the fuel. Hence the metal can be either oxidized or gassed, but it is doubtful whether these actions can take place simultaneously. Oxidation can be easily overcome by the use of deosidizers or it may be avoided by protecting the molten metal with suitable fluxes. Absorption of gascs is more difficult to overcome: the regulation of the air and fuel, so as to produce complete combustion, and the protection of the bath by mineral fluxes arc the most important factors. Gas expulsion, resulting in gas holes, porosity, unsoundness, and swollen or cauliflower-headed risers, is said to have several causes. One writer1 lists the most common causes in the order of their importance, as follows: Superheated metal, dirty or slaggy furnace conditions, using metals low in quality or those previously subjected to bad melting practice, poor grade of fuel, use of newly lined or damp ladles, indiscriminate mixing of scrap or illogical combinations of metal. Superheating the metal usually occurs when the heat is ready to be poured but for some reason must be held in the furnace. In this case, a careful furnace tender tries to avoid overheating the metal by keeping a mild fire; that is, a reducing fire which, unfortunately, results in gassing the metal. A dirty, slaggy furnace may result in gassing the metal by retarding the heating and prolonging the time necessary to bring the metal to the proper temperature, thereby increasing the chances of gassing in uncertain furnace atmosphere. It is doubtful whether rnetals of low quality have anything to do with gassing molten metal, except, possibly in the case of metals containing

Jan 1, 1923

By B. Woyski

Many writers, in discussing defects caused by oxidation and gassing of bronzes and red brasses advocate substantially the same cure for both. But from its nature, oxidation cannot take place if there is an excess of fuel in the furnace, while the gases absorbed by some alloys are products of incomplete combustion of the fuel. Hence the metal can be either oxidized or gassed, but it is doubtful whether these actions can take place simultaneously. Oxidation can be easily overcome by the use of deosidizers or it may be avoided by protecting the molten metal with suitable fluxes. Absorption of gascs is more difficult to overcome: the regulation of the air and fuel, so as to produce complete combustion, and the protection of the bath by mineral fluxes arc the most important factors. Gas expulsion, resulting in gas holes, porosity, unsoundness, and swollen or cauliflower-headed risers, is said to have several causes. One writer1 lists the most common causes in the order of their importance, as follows: Superheated metal, dirty or slaggy furnace conditions, using metals low in quality or those previously subjected to bad melting practice, poor grade of fuel, use of newly lined or damp ladles, indiscriminate mixing of scrap or illogical combinations of metal. Superheating the metal usually occurs when the heat is ready to be poured but for some reason must be held in the furnace. In this case, a careful furnace tender tries to avoid overheating the metal by keeping a mild fire; that is, a reducing fire which, unfortunately, results in gassing the metal. A dirty, slaggy furnace may result in gassing the metal by retarding the heating and prolonging the time necessary to bring the metal to the proper temperature, thereby increasing the chances of gassing in uncertain furnace atmosphere. It is doubtful whether rnetals of low quality have anything to do with gassing molten metal, except, possibly in the case of metals containing

Jan 1, 1923

By B. B. Cox

The Iraq Petroleum Company, Ltd. continued its systematic exploration and exploitation of the Kirkuk field on a unitized basis. Pressures, gas-oil ratios, oil-water level and oil-gas level remained satisfactory. All wells were produced by flowing and more than two-thirds of the crude was stabilized. The only exports from Iraq during 1937 were from the Kirkuk field. Mosul Oilfields, Ltd., through its operating subsidiary, the British Oil Development Company, Ltd., inaugurated an exploratory program to find lighter oil than the heavy, black, sulphurous reserve proved in the Qaiyarah-Najmah-Jawan-Qasab field. Deeper drilling in this field found a small reserve of 17" to 19" A.P.I. black sulphurous oil in the Pilsner (Upper Cretaceous). Ten structures outside the proved field were tested or were under test at the end of the year. In spite of this intensive program no reserve of lighter oil was discovered. The reserve at Qaiyarah-Najmah-Jawan-Qasab averages 16" A.P.I. with 6+ per cent sulphur from the "continuous limestone" (Lower Miocene, Oligocene, Middle Eocene) and from the Pilsner (Upper Cretaceous). The Khanaqin Oil Company, Ltd., a subsidiary of the Anglo-Iranian Oil Company, Ltd., conducted the normal exploitation of its Naft Khaneh oil field and supplied the local Iraq market requirements. Slightly more than 31,600,000 bbl. of crude was produced in Iraq during 1937. The following table gives the total crude produced by the I.P.C. for export during the last four years. Year 42-gallon BarreL Increase over Preceding Year 1934 7,096,669 1935 27,014,904 19,918,235 1936 29,521,053 2,506,149 1937 31,171,476 1,650,423 " Converted at an average of 7.6 bbl. per ton. Published by permission of the Near East Development Corporation. Manuscript received at the office of the Institute March 11, 1938. * Geologist, Socony-Vacuum Oil Co., Inc., New York, N. Y.

Jan 1, 1938

By P. A. Beck, W. D. Manly

In a recent note Sully and Head1 showed that the Cr-Fe sigma phase is isomorplious with the Cr-Co gamma phase, and that the lattice constants are also nearly identical. In a preliminary investigation of the ternary Cr-Co-Fe system at 800°C at this laboratory the above findings were confirmed, and it was found by microscopic techniques, using various etching reagents, that the two binary phases form an urinterrupted series of solid solutions with each other. These solid solutions occupy a straight narrow band which cuts across the 800°C isothermal section of the ternary system, connecting the two binary phases. A detailed investigation of the Cr-Co-Ni ternary system at 1200°C disclosed that here, too, the Cr-Co gamma phase extends deep into the ternary system in the form of a long narrow lip. The fact that this sigma type lattice is sustained even when well over half of the Co atoms in it are replaced by Ni atoms, with relatively little change in the Cr content, clearly indicates that Ni itself has a certain tendency to form the sigma phase with chromium. This tendency is hidden in the binary Cr-Ni alloys, where the sigma phase is not known to occur, but it becomes operative in the presence of a suficient amount of Co. The interpretation of these facts in terms of electron concentrations is rendered difficult by the uncertainty of our present knowledge of the valency electron structure of the transition elements in their alloys. However, Sully and Heal&apos;s results and the present work suggest that intermetallic phases with signla type lattice may occur more frequently in these little investigated alloys than heretofore suspected. In particular, it is expected that a similar phase may exist in the V-Co and perhaps in the V-Ni system, in analogy to the known sigma type phase in the V-Fe system, and that all these sigma type phases may form extensive solid solutions with one another.

Jan 1, 1950

By C. B. Post, G. V. Luerssen

J. STEVENS*—The authors state that the contamination in the metal was due mostly to the ladle refractories. Did the contamination vary with different brands of refractories or different qualities in the ladle ? C. B. POST (authors&apos; reply)—That would be expected. In our shop we have used a grade of firebrick which is fairly standard. We do use high refractory nozzles to combat this erosion and high refractory sleeves, but there is such a problem when you get a skull in a ladle you just cannot use these high refractory bricks; you rip out the whole ladle getting the skull cleaned up. The acid bricks form a glass, and you can pull the skull out when you do get them. I believe you might find variations among the different refractories depending on how much silicon is in the brick. This determines how much silica is going into the interface between the steel and the brick. Our brick is about 35 pet alumina and 65 pet silica. With a brick of 35 pet alumina in the slag patches new calculations would have to be made. R. PARDEE*—Where can you draw the line in determining the refractories as being a silica refractory ? C. B. POST—More silica than about 50 pet. I think perhaps that is generally the criterion. The brick we use is a good high grade fire brick. T. S. WASHBURN*--With reference to the higher silicon that is recommended as a result of this investigation, is it contemplated that the specified range would be raised to 0.40-0.60 pet silicon, or possibly 0.50-1.00 pet silicon? These higher silicon ranges would affect the physical properties of the steel and consequently there might be some complications with respect to educating the consumers to &apos;accept this revision of the conventional analysis. C. B. POST—It will take considerable work. Take AMS 6260 as an example. Ordinarily this specification calls for 60 or 75 manganese. Silicon has some

Jan 1, 1950

By George R. Mansfield

INTEREST in the reserves of phosphate rock in the United States and their proper conservation has recently been aroused by hearings held in different parts of the country by the "Joint Committee to investigate the adequacy and use of phosphate resources of the United States." This committee was appointed within a few days after a Presidential message to Congress on the same subject, dated May 20, 1938, and began to function almost immediately. Hearings were held in Washington, D. C., Pocatello, Ida., Wilson Dam, Ala., Knoxville, Tenn., and Lakeland, Fla. The resulting testimony, when published, comprised a volume of 1182 pages.1 At the earlier hearings held in Washington and Idaho the seeming disparity between the great reserves of the West and the smaller reserves in the East led to some suggestions as to the desirability of curtailing or even prohibiting the exportation of phosphate rock so that eastern producers, becoming alarmed, cooperated in making available for the use of the committee information hitherto closely guarded. This information has provided an opportunity for new studies by official agencies, for a restatement of the reserves of Florida and Tennessee, and for some modification of figures for the Western States. The writer, representing the Federal Geological Survey, was given free access to the Florida material and has prepared for publication a report,2 some features of which are summarized in this paper. The Tennessee material was studied by Dr. G. I. Whitlatch,3 of the Tennessee Division of Geology. Prof. J. Stewart Williams,4 of the Utah State Agricultural College at Logan, has published a recent study of the phosphate resources of Utah and the writer has given some further study to reserves of western phosphate from the viewpoint of including material of lower grade than that hitherto considered. Technologic advances in the phosphate industry must be credited with a large share in the expansion of reserves by making available for

Jan 1, 1940

By Guillermo Mariaca, Jorge Muñoz Reyer

As far as technology is concerned there has been no development in Bolivia during the year 1936, because the country, just emerging from the war with Paraguay, is only beginning to rebuild its economic foundations. Great steps, however, are being taken in order to secure a rapid and sound development of its oil resources, as follows: 1. The new Petroleum Law, which contemplates the problem of proration and conservation of natural resources, prohibiting the wasteful use of gas, and regulating the number of wells, their spacing and the permissible output per well, for each particular pool according to the conditions prevailing therein. 2. The creation of an official entity with the object of developing and exploiting a large petroliferous area. This entity has been called Yacimientos Petroliferos Fiscales Bolivianos (Y.P.F.B.), and the region assigned to it is all the sub-andean zone, which is approximately one hundred miles wide and borders the eastern part of the Oriental Andean range, from Argentine to Peru. It is said that drilling will be started immediately in various localities. At the present time a wide geological survey of part of the area is being made in order to find out which regions offer the best possibilities of commercial development. Y.P.F.B. has been authorized by the Government to draw up contracts with private companies for the exploitation of limited zones. Production The only company that has been producing in the country in 1936 is the Standard Oil Company of Bolivia, and only from two of its fields: Camiri and Sanandita. New wells were not drilled. During the first nine months of the year 12,762,958 liters (80,275 bbl.) was produced, 34,985 bbl. from the Camiri field and 45,290 bbl. from the Sanandita field. Reports for October, November and December are not yet available. The total for the year 1935 was 25,978,737 liters (163,388 bbl.).

Jan 1, 1937

By Warden A. Moller

The Fushun coal-field, now being opened up by the South Manchurian Railway Co., is connected with the main line by a branch, 30 miles long, from Sui Chia Tun, 10 miles south of hlukden, the oapital of Manchuria. The coal-field, which lies on the southern bank of the Hun river, 25 miles east of Xiukden, consists of a long narrow valley, running east and west between hills composed of granitic and volcanic rocks. At the foot of the northern hills, the Hun river flows westward towards the Liao river, which drains the greater part of South Manchuria. At the foot of the southern hills, resting immediately upon volcanic rocks, and overlain by 30 ft. of alluvium, is a thick layer of Tertiary shales, carrying near the base two coal-seams. In many places the lower of these two seams is in immediate contact with volcanic lavas and basalts, the flows of which were evidently both prior and subsequent to the formation of the coal-seams. This contact has practically destroyed the lower seam for commercial purposes. The value of the field lies in the upper seam, which, for a length of nearly 8 miles, varies from 100 to 130 ft. thick. Of this seam, 85 per cent. is good coal. The seam dips to the north conformably with the shales, at angles of from 25 to 30°, and appears to have an uninterrupted dip for about 1.5 miles before being possibly cut oft&apos; by the northern hills. The coal-bearing shales extend east and west for a length of about SO miles, but towards the east the continuity of the seams is broken by intrusive rocks. The coal is of the sub-bituminous variety, low in ash, bright in appearance, and breaks with a conchoidal fracture. It has the usual qualities of Tertiary coal—quick steam-raising and poor stacking qualities. Pieces of resin, varging in size from

Jan 1, 1911

By W. C. Weslow

AN extended program devoted to the development of a matrix for holding diamonds of a size and kind not heretofore generally used is being carried on by the Carboloy Company, and this paper describes the part of the development that affects mining and its allied industries. Laboratory and field work so far has indicated the following: 1. Tungsten carbide and cobalt form the most desirable known matrix material for the holding of diamonds for drilling work. 2. Industrial bort diamonds in sizes and of a class not generally heretofore acceptable and therefore less expensive can be successfully held in this cemented carbide matrix. 3. In exploratory drilling, the combination of bort diamonds, impregnated throughout a matrix of tungsten carbide and cobalt, when fabricated onto drilling crowns, is an indicated economic substitute for drilling crowns in which the diamonds are set by hand, mechanically or by casting. 4. This impregnated type of drilling crown or bit has definite possibilites of revolutionizing the drilling of blast holes, particularly in the harder formations. This will be brought about by the development of high-speed light-weight rotary equipment using an impregnated diamond bit to replace the percussion drill now in general use. (The development of this rotary equipment is well past the laboratory stage at this time.) 5. That the use of a rotary bit is a preventive measure in the fight against silicosis. The development of this product was started by G. F. Taylor at the Research Laboratories of the General Electric Co. It was early recognized that it had possibilities in the drilling field and the present product is the result of considerable experimental work with other powdered metals as well as with tungsten carbide and cobalt. In the study of the potential application to the mining field, it was learned that carbon diamonds originally were given a high rating of performance but that the trend had been toward borts in selected sizes

Jan 1, 1940

By B. M. Loring, I. R. Krame, F. M. Walters

NO observations on the mechanical properties of man-manganese alloys have been published since pure manganese became readily available, either distilled manganese or electrolytic manganese. The purpose of this investigation was to determine whether iron-manganese alloys are essentially brittle, as reported by Hadfield,&apos; or whether the lack of ductility observed was due to impurities in the alloys that he studied. Experimental Methods The alloys were melted in a roo-lb. high-frequency induction furnace with a magnesia crucible, using ingot iron and electrolytic manganese. The heats were split, the first giving six 18-lb, ingots and the second three. Each successive heat was higher in manganese and about 0.3 per cent silicon was added as ferrosilicon. The alloys forged without difficulty and were given a 9&apos; per Published by permission of the Navy Department. Manuscript received at the office of the Institute June 28. 1941. Issued as T.P. 1369 in Metals Technology. September 1941. * Division of Physical Metallfirgy Naval Roscarch Laboratory. Anacostia Station Washington. D. C. 1 References are at the end of the paper. 4 cent reduction to ¾-in. rounds. The chemical analysis of the alloys is given in Table I. The forged rods were homogenized for 224 hr. at r150°C. (2100°F.) and air-cooled. The alloys were tested in two conditions of heat-treatment: (I) as normalized from 870°C. (1600°F.) and (2) normalized from 870°C. and tempered for I hr. at 540°C. (Iooo°F.) and air-cooled. The tensils specimens were 0.505 in. in diameter with a 2-in. gauge length, and the impact specimens were v-notch Charpy. The proportional limit and yield strength were taken from the stress-strain diagrams drawn by a Peters recorder. The data obtained from the tensile test and the hardness measurements are given in Table 2. Specimens that were normalized are designated by N; those that were normalized and tempered by T. Alloy G was tempered after forging (D).

Jan 1, 1942

By J. J. Strohl, H. J. Schwellenbach

This paper relates the results obtained by decreasing the size of feed to a rod mill screen circuit. As would be expected, added production was gained and a finer grind with no tonnage loss was made possible. THE MacIntyre mill of the National Lead Co. has four parallel sections in which magnetic and gravity separations are made. Ore from a 5000-ton bin is fed by Hardinge constant weight feeders to a 6x12-ft open-end Marcy rod mill in each section. Rod mill discharge is bucket elevated to two 4x10-ft Tyrock screens whose oversize is returned to the rod mill. Screen undersize is pumped to Crockett separators for magnetite removal, and the Crockett tailings are sized and tabled to make an ilmenite concentrate. Minus 200-mesh material, overflowed by the Crockett and Dorrco sizers is thickened, de-slimed, and concentrated by flotation.&apos; By 1948, the development of a successful slime flotation process and numerous improvements in the gravity circuit of the mill had increased the capacity of the available concentrating equipment. At the same time, improvements in the operating techniques of the dry crushing plant and improved feeding of the crusher by the mining department had appreciably increased the production rate per operating hour in that plant. Therefore, it was decided to take advantage of the added crusher capacity to produce a finer rod mill feed and in that way increase grinding capacity. At approximately the same time, finer screens were installed in the rod mill circuits to give finer grind and thus improve liberation of the magnetite and ilmenite from the gangue and from one another. Prior to the first part of 1948, a 3/4-in. limiting screen was used for sizing rod mill feed. The first reduction in crushing plant screen size was to 1/2 in. With this screen, the circulating load in the tertiary crushing circuit was too high and plant capacity dropped below a practical hourly rate. A 9/16-in.-sq opening screen, installed next, proved satisfac-

Jan 1, 1951

Arrangements have been completed in New York whereby the re- sources of The Engineering Foundation, under the auspices of the four principal national engineering societies, are placed at the disposal of the National Research Council, which was appointed by the National Academy of Sciences* at the request of President Wilson. The object of the Council is to coordinate the scientific research work of the country in order to secure efficiency in the solution of the problems of war and peace. The Council was without funds until The Engineering Foundation, established to further scientific and engineering research, offered to place its resources at the Council&apos;s disposal, including the services of its secretary, Dr. Cary T. Hutchinson, to act as-secretary of the Council. The offer was accepted and plans for immediate activities have been placed in the hands of an executive committee. In indicating how thoroughly, every branch bf science and engineering is represented, Dr. George E. Hale, Director of the Mt. Wilson Solar Observatory, and Chairman of the Council, when he was in New York attending to the details of the arrangement, called attention to the personnel of the body, saying that it is the purpose to enlist the cooperation, in the solution of our industrial and military problems of a scientific character, of every possible established agency. Medicine, for example, is represented on the Council by Dr. William H. Welch, President of the National Academy of Sciences, Brigadier General William C. Gorgas, , Surgeon Crenera.1 of the United States Army, Dr. Simon Flexner, Director of the Rockefeller Medical Institute, and Dr. Victor C. Vaughan, Past President of the American Medical Society; biological science by Dr. Edwin G. Conklin, Professor of Zoology, Princeton University; chemistry by Dr. A. A. Noyes of Massachusetts Institute of Technology and Dr. L. H. Baekeland; physics by Dr. A. A. Michelson of the University of Chicago; and electricity by Professor M. I. Pupin, of Columbia University.

Jan 10, 1916

By H. J. Schwellenbach, J. J. Strohl

This paper relates the results obtained by decreasing the size of feed to a rod mill screen circuit. As would be expected, added production was gained and a finer grind with no tonnage loss was made possible. THE MacIntyre mill of the National Lead Co. has four parallel sections in which magnetic and gravity separations are made. Ore from a 5000-ton bin is fed by Hardinge constant weight feeders to a 6x12-ft open-end Marcy rod mill in each section. Rod mill discharge is bucket elevated to two 4x10-ft Tyrock screens whose oversize is returned to the rod mill. Screen undersize is pumped to Crockett separators for magnetite removal, and the Crockett tailings are sized and tabled to make an ilmenite concentrate. Minus 200-mesh material, overflowed by the Crockett and Dorrco sizers is thickened, de-slimed, and concentrated by flotation.&apos; By 1948, the development of a successful slime flotation process and numerous improvements in the gravity circuit of the mill had increased the capacity of the available concentrating equipment. At the same time, improvements in the operating techniques of the dry crushing plant and improved feeding of the crusher by the mining department had appreciably increased the production rate per operating hour in that plant. Therefore, it was decided to take advantage of the added crusher capacity to produce a finer rod mill feed and in that way increase grinding capacity. At approximately the same time, finer screens were installed in the rod mill circuits to give finer grind and thus improve liberation of the magnetite and ilmenite from the gangue and from one another. Prior to the first part of 1948, a 3/4-in. limiting screen was used for sizing rod mill feed. The first reduction in crushing plant screen size was to 1/2 in. With this screen, the circulating load in the tertiary crushing circuit was too high and plant capacity dropped below a practical hourly rate. A 9/16-in.-sq opening screen, installed next, proved satisfac-

Jan 1, 1951

By B. M. Loring, I. R. Krame, F. M. Walters

NO observations on the mechanical properties of man-manganese alloys have been published since pure manganese became readily available, either distilled manganese or electrolytic manganese. The purpose of this investigation was to determine whether iron-manganese alloys are essentially brittle, as reported by Hadfield,&apos; or whether the lack of ductility observed was due to impurities in the alloys that he studied. Experimental Methods The alloys were melted in a roo-lb. high-frequency induction furnace with a magnesia crucible, using ingot iron and electrolytic manganese. The heats were split, the first giving six 18-lb, ingots and the second three. Each successive heat was higher in manganese and about 0.3 per cent silicon was added as ferrosilicon. The alloys forged without difficulty and were given a 9&apos; per Published by permission of the Navy Department. Manuscript received at the office of the Institute June 28. 1941. Issued as T.P. 1369 in Metals Technology. September 1941. * Division of Physical Metallfirgy Naval Roscarch Laboratory. Anacostia Station Washington. D. C. 1 References are at the end of the paper. 4 cent reduction to ¾-in. rounds. The chemical analysis of the alloys is given in Table I. The forged rods were homogenized for 224 hr. at r150°C. (2100°F.) and air-cooled. The alloys were tested in two conditions of heat-treatment: (I) as normalized from 870°C. (1600°F.) and (2) normalized from 870°C. and tempered for I hr. at 540°C. (Iooo°F.) and air-cooled. The tensils specimens were 0.505 in. in diameter with a 2-in. gauge length, and the impact specimens were v-notch Charpy. The proportional limit and yield strength were taken from the stress-strain diagrams drawn by a Peters recorder. The data obtained from the tensile test and the hardness measurements are given in Table 2. Specimens that were normalized are designated by N; those that were normalized and tempered by T. Alloy G was tempered after forging (D).

Jan 1, 1942

By Lewis T. Wright

It is commonly believed by metallurgists that in copper-smelting, the copper in the slags, which is irreducible by continued " settling," is retained in the form of " prills " of matte. I have frequently held well-settled slag in a molten condition for a long period without being able thereby to reduce the copper-content. The slag acted as though it contained a minimum of dissolved or combined copper that could not be settled out by gravity. I have used reagents, but without satisfying myself in what form this copper existed. The same slags, by fine grinding and elutriation, could not be separated into portions containing more or less copper than the average content. By treating copper-slags in an electric furnace a button of metallic iron and copper was produced, but the high temperature and the strong reducing-action of the furnace mere influences that suggest an explanation of a result not obtainable with ordinary smelting-temperatures. If all the copper in the slag were in the form of copper-matte, and not existing as a dissolved compound with some of the elements of the slag, then the other metals in the matte, such as gold and silver, should occur in the slag in the same ratio to the copper as to the copper in the accompanying matte. This reasoning led me to study the ratio of metals in the products of smelting, and, apart from the issues discussed in this paper, the research has proved both interesting and illuminative. On the assumption of a similar ratio of metals in matte and slag, if the percentage of copper in the slag accompanying a matte containing 50 oz. of silver and 1 oz. of gold per ton of copper was 0.3 per cent., or 96 oz. per toll of slag, there should be found 0.15 oz. of silver and 0.003 oz. of gold per ton of slag; but, in my experience, there is less silver and much

Jan 1, 1910

By W. G. Matteson

THE Oklahoma legislature recently passed a bill providing for "the creation of an oil and gas department under the jurisdiction of the Corporation Commission, authorizing the. Corporation Commission to appoint a chief oil and gas conservation agent, and conferring exclusive jurisdiction on the Corporation Commission in reference to the conservation of oil and gas, and the inspection of gasoline and oil, the product of crude petroleum, and repealing all acts or parts of acts in conflict therewith and declaring an emergency." Some of the functions of the new bureau include the receiving and filing of all well logs and the direction and supervision of plugging all abandoned oil and gas wells under rules prescribed by the Corporation Commission. The two leading petroleum-producing States of the country, Oklahoma and California, have now established oil and gas bureaus with a staff of inspectors to see that the important rules relating to the conservation of oil and gas are thoroughly enforced. The economic significance and the value of well logs in the conservation work has been recognized and the necessary legal action taken to insure and procure them. William B. Heroy, of the Government Land Classification Board, in a personal communication to the writer, says that the drilling of wells is also regulated by public authority in the Roswell artesian basin in southeastern New Mexico, where a permit must be obtained for the drilling of any well and a certified log of the well recorded with a county official. The method is said to give fairly satisfactory results. In a recent article 1 a National instead of a State Bureau was suggested for collecting and filing well logs. In discussing the paper, L. L. Hutchison characterized such a plan as impractical because the average driller or contractor will often juggle or guess at the log and will not keep the record sufficiently close or accurate, making it necessary to maintain a special man at each well for the sole purpose of obtaining

Jan 6, 1917

By Robert B. McCormick

THE major use for quartz crystal is in the manufacture of radio oscillator plates and telephone resonator and filter crystals. Quartz crystal is also cut and polished as a semiprecious gem stone, particularly in the colored varieties (amethyst, Brazilian topaz, and others), and often is carved into various objects of art. Prisms, wedges, lenses and other optical parts often are made of quartz crystal, usually for special- purpose instruments. Chips and small clear crystals below 100 grams in weight, called “lascas” by the trade, are the raw material for fused quartz products. HISTORICAL BACKGROUND The Greeks believed quartz to be permanently frozen water and therefore called it krustallos, which, literally translated, means clear ice; but ages before their civilization, prehistoric man had crudely cut and polished crystals for rough charms and ornaments. About 2000 B.C., the Egyptians brought the art of cutting quartz to a high level. While there are earlier examples of crystal art that have great value, working in crystal during that period became a means of artistic and religious expression that has endured through the ages. Art museums and private collections throughout the world contain many priceless pieces. They include findings from the tombs of the earliest Egyptian rulers, as well as magnificent art objects in both clear and colored crystal encrusted with silver, gold, enamel, and precious gems of oriental and European workmanship. Pierre Curie first measured the piezoelectric effect of quartz, in 188 1, by placing a weight on the surface of a quartz crystal and measuring the resulting electrical charge, which he found was proportional to the weight applied. The following year the inverse piezoelectric effect was proved by the Curies. By applying a voltage to a piece of quartz, a measurable physical displacement occurs. The first practical application of this effect was the construction of a bimorph unit to measure voltage by measuring the amount of the displacement of the end of the bimorph. The piezoelectric properties of quartz crystal remained largely a laboratory curiosity until World War I, when a supersonic device for

Jan 1, 1949

By A. S. Richardson

VENTILATION of the Butte mines has long been a rather difficult problem because of the natural high temperature of the rock. With increase in mining depth, higher rock temperatures have been encountered, and this has caused a constantly growing demand for more effective ventilation measures. During recent years the hazards of dust in mine air have been more clearly recognized, and have necessitated the adoption of dust-prevention methods. To meet these ventilation problems in the mines of the Anaconda Copper Mining Co., a mines ventilation department was organized in 1918, to act under the direction of the general superintendent of mines. At the present time, under normal operating conditions, the force employed includes the ventilation engineer, two chief assistant ventilation engineers and eight assistant ventilation engineers. The activities of the department are, briefly: (1) planning and supervising operation of the general ventilation system; (2) planning and supervising the operation of dust-prevention measures, together with dust sampling and related microscopic work for the quantitation of the dust samples and determination of particle-size distribution; (3) the design and development of air- conditioning methods to meet present exceptionally severe temperature conditions and in anticipation of future requirements. To a large extent the technical features of the ventilation methods have been described in earlier papers by the author. This paper is written mainly to summarize past accomplishments bearing most closely on health and safety, with a somewhat more detailed account of the dust- prevention measures that have been developed comparatively recently. FACILITATING FLOW OF AIR As a basic requirement for the safety of the men, all ventilation plans are subject to a ruling that the main operating shafts must be maintained as inlet air courses. Under this condition, a safe, fresh-air escapeway is assured if a fire occurs within the mine, and the shaft is available as a base for fire-fighting operations. Control of the direction of air flow is

Jan 1, 1938