Search Documents

By J. S. Jacobi

Treating copper ores by heap-leaching and similar hydrometallurgical means is a time-honored practice, which was well known even in the 19th century. Later the method lost ground to better ore dressing processes, particularly selective. flotation. More recently there has been a distinct reversion to leaching techniques, particularly for scavenging operations in old mining stopes, in connection with LPF systems, irrigation of tailings dumps and similar situations. These hydrometallurgical techniques will gain further ground because processing is simple and permits better extraction of copper, particularly from low-grade or partly oxidized ores. In the lixiviation of primary ores at some major operations, copper-bearing liquors may undergo re-circulation in heap-leaching arrangements or the ores may be subjected to systematic percolation treatment. The liquors resulting from this source usually are quite strong (above 10 gpl copper) and copper would normally be reclaimed by electrowinning or cementation. These processes fall out- side the scope of this paper which is concerned with recovery of copper from weak 1iquor.s containing from 0.1 to about 3 gpl copper.

Jan 9, 1963

By J. B. Clark, F. N. Rhines

brittlement or notch sensitivity progressively increases. Further, in contrast to results obtained with the impact test, the notch strength for the large specimens does not reveal a 500°F embrittlement range. The notch sensitivity as determined with the 0.3-in. specimen of 4340 steel given the stepped austenitizing treatment has been discussed elsewhere. This quantity as measured for the 1.1-in.- diam notch tensile test and given in Fig. 3, is taken to signify that reduced notch sensitivity is encountered in the 600" to 800°F tempering range for specimens given the stepped austenitizing treatment. The stepped austenitizing treatment may, there- fore, be of use in promoting deeper hardenability for a 4340 steel while at the same time giving reduced notch sensitivity in the high-strength range in which this steel is now being used. Acknowledgments The work reported was supported by the U. S. Navy Bureau of Aeronautics. The authors are indebted to the Bureau of Aeronautics for granting permission to publish results of this research and to N. E. Promisel, H. Hessing, and J. Maltz for their interest.

Jan 1, 1958

In Bulletin J 1, recently published by the Traylor Engineering and Manufacturing Co., it is stated that the largest jaw crusher ever built has a jaw opening of 66 in. by 86 in. and weighs 680,000 1b. It is said to be in successful operation and has a capacity of 490 tons per hour crushed to 12-in. size; 415 tons per hour crushed to 10-in. size; 330 tons per hour crushed to 8-in. size. The same company, in its Bulletin G 3, gives a diagram showing the percentage of a crushed product which will pass through screens of different sizes of perforation from a machine adjusted to a certain size screen. This diagram is reprinted below for the information of our members and the following notes apply to it. In order to prevent an excessive amount of fines, crushing machines are usually set so that 15 per cent. of the product will be larger than the maximum size desired, and this oversize is then recrushed by smaller

Jan 10, 1916

Detailed Geology of Certain Areas in the Mineral Hill and Warm Springs Mining District. By A. L. Anderson. T. H. Kilsgaard and V. C. Fryklund. Jr. Idaho Bureau of Mines and Geology. University of Idaho. 73 P. Maps, Illus.-Divided into three parts, this pamphlet covers the geology and ore deposits of the Hailey-Bellevue Mineral Belt, the Triumph-Parker mine mineral belt, and the ore deposits of the Mayflower Area. Numerous maps and illustrations are included for each area. Government Administration of the Copper Industry, World War 11. By John W. Douglas. 1950.51 P. $1.-This pamphlet covers in detail all the steps relating to control and operation of copper and copper products, and is of particular interest to primary producers, brass mills, wire mills, and foundries. Of particular current interest is the booklet's coverage of the steps leading to the Controlled Material Plan, into which industry is now once again heading. Copies can be obtained for $1 from John W. Douglas, Republic Foil & Metal Mills Inc., 55 Triangle St., Danbury, Conn.

Jan 12, 1951

By Dennis V. D’Andrea, Sidney M. Runke

This paper describes the Bureau of Mines-El Paso Mining and Milling Company cooperative research program at the Emerald Isle mine3 near Kingman, Ariz. This research program was directed toward developing in situ leaching methods for 200,000 tons of ore exposed in the pit bottom and also 1,500,000 tons of ore under 200 feet of overburden adjacent to the pit. A test area in the pit bottom containing 15,000 tons of ore was blasted and leached. The results of this leach test were encouraging, and the entire pit bottom was leached in-place for about 7 months. Two test blasts under 200 feet of overburden and extending to 290 feet were detonated in an area near the open pit. The results of these blasts were evaluated by core drilling and permeability measurements. An in situ leaching system was designed, but not implemented, to recover copper from the 1,500,000-ton area near the pit. The company decided to terminate operations at the Emerald Isle mine in November 1975.

Jan 1, 1976

By E. C. Wright, P. W. Mumma

This paper describes some properties of steels in the composition range 0.10 to 0.30 per cent carbon and 1 to 7 per cent chromium. It is well known that some steels of this type develop high tensile strengths upon receiving comparatively simple heat treatments, such as ordinary air cooling from appropriate temperatures, with or without subsequent tempering treatments. These high strengths are frequently associated with unusual toughness as measured by the Izod or Charpy impact test. The chromium content, in addition to imparting the above properties, enhances the resistance to corrosion and improves the strength and oxidation resistance at elevated temperatures. Moreover, these steels have good forging and fabricating properties, as evidenced by the fact that several thousand tons of seamless tubing have been made during the past five years from steels containing 0.10 to 0.25 per cent carbon and 5 per cent chromium. Composition and Properties of Materials Tested Twelve 15-lb. induction furnace heats of the compositions shown in Table 1 were prepared, using low-carbon open-hearth steel base melts

Jan 1, 1933

By A. Arrott, G. S. Ansell

A model is proposed to account for the observed strengthening behazlior of ferrous martensites. me model is based upon the inheritance of carbon-rich regions by the martensite which were present in the FERROUS martensite is formed by a nucleation and shear mechanism when austenite is cooled, at a rate which is fast enough to suppress the formation of pearlite, below a critical temperature (Ms ). Although the mechanism of the transformation process appears to be well understood,1,2 the mechanism re- austenite prior to transformation. These carbon-rich regions strengthen the martensite in a manner analogous to the strengthening effect due to a finely dispersed second phase. sponsible for the observed high strengths exhibited by ferrous martensites is uncertain. In this paper, a model is proposed to account for the strengthening of ferrous martensite. MODEL The maximum solubility of carbon in austenite is 1.98 wt pct as compared with a maximum solubility of 0.025 wt pct in ferrite. Prior to transformation, the carbon in the austenite is nonuniformly dis-

Jan 1, 1963

By Jerry A. Selvaggi, Richard B. Jacob

The High Gradient Magnetic Separator (HGMS), also known as the High Gradient Magnetic Filter (HGMF), is an effective device utilized in magnetic separation. This method of separation is gaining popularity in the separation of submicron material containing feebly magnetics. The most common use of this type of separator is in the removal of iron stained particles to improve the brightness of kaolin clay. Potential areas for use of this magnet include: (1) desulfurization of coal (2) the clean-up of mill effluent (3) removal of fine particulate matter from municipal and indus¬trial waste (4) desulfurization of oil Design, operation, and applications of this separator are further dis¬cussed in papers by R. R. Oder (1975), and R. R. Oder and B. I. Horst (1975). This device is a system composed of an iron enclosure of high per¬mability material housing a set of electrical coils, a canister en¬closing a magnetic matrix (stainless steel wool), an electric power supply and a hydraulic system to maintain specified operating tempera¬ture conditions. See Figure 1.

Jan 1, 1984

The following rules, upon approval by the Board of Directors, shall serve as guides in the practical applications of the Bylaws for the operation of the Institute and have the full power and effect of Bylaws, however, these rules may be changed, modified, re¬pealed or amended when deemed necessary by the Board of Directors Any change or alteration of these Rules shall be published in the Journals of the Institute within three months after such alteration is adopted ARTICLE I-ORGANIZATIONS OF THE INSTITUTE Section 1-Societies Rule 1-Governing Body Each Society shall form its own governing body composed of an Executive Committee, or similarly designated executive body, duly elected officers, and a Nominating Committee for the nomination of Institute officers as provided by the Bylaws of AIME and of each Society approved by the Board In all correspondence and printed matter the Society Boards of Directors shall be specifically identified For ex¬ample, the Mining Board of Directors or the Board of Directors of the Society of Mining Engineers Using simply the "Board of Directors" could cause confusion

Jan 1, 1960

By D. F. Stoneburner, G. Derge, Ling Yang

PREVIOUS investigations in this laboratory have shown the existence of electronic conduction in several molten metal sulfides and the specific conductance of a number of these has been measured as a function of temperature.' In order to better understand the electronic nature of these melts, the thermoelectric power of a molten FeS-solid tungsten thermocouple was measured and a value of approximately 55 µv per "C was obtained in the temperature range from 1200" to 1400c2 These studies have been continued and the thermoelectric power of several other molten metal sulfide-solid tungsten thermocouples have been obtained. The experimental arrangement is shown in Fig. 1. A Kanthal furnace was used, doubly wound to prevent any undesirable effects of an external field. A 1/2-in. McDanel tube was fitted with two vertical 5/8-in. McDanel tubes as shown. These tubes were about 2 in. apart. A graphite boat was used to hold a re-crystallized alumina boat in which the prefused sulfide was placed. Two probes were made using

Jan 1, 1960

By W. H. Emerson

In the summer of 1894, a specimen of corundum from Acworth, Ga., which mas reputed to be of markedly inferior quality for the manufacture of corundum-wheels, was received by the Geological Survey of Georgia, with the request that it be analyzed, in order to ascertain whether this inferiority was associated with any peculiarity of composition. In its appearance there was nothing uncommon, though it seemed to be rather easily scratched with a knife, while, at the same time, it scratched agate easily. An analysis gave the following results: Alumina, 94.58; silica, 1.77; magnetic oxide of iron, 0.69; calcium oxide, 0.44; and water, 2.51 per cent. There is nothing unusual in this composition, except the amount of water, which is usually, in southern corundum at least, from 0.3 to about 1 per cent. Concerning this corundum, the Mineral Resources of the United States, 1893, pp. 676 and 677, Bays: "It is supposed that this variety of corundum contains a little water, as it is

Jan 1, 1900

By Francis T. Havard

A Reply to the Discussion by Mr. Francis T. Havard of the Paper by Mr. Henry W. Edwards, which was read at the Atlantic City Meeting, February, 1.904. (Annual Meeting, February, 1905.) MR. HENRY W. EDWARDS, Grand Junction, Colo. (communication to the Secretary) :* Effect of Heat. It should be remembered that the coefficient of expansion of concrete is nearly that of iron; therefore in constructing flues the design must take account of this important detail. The cracking of flues, mentioned by Mr. Havard as having occurred at a temperature of 100° C. and above, . were possibly caused by neglecting to appreciate the extent of the expansion and contraction of the concrete. Effect of Atmospheric Moisture.-The moisture present in the atmosphere is exceedingly injurious to flues of any material, and those made of concrete are no more susceptible than of brick. My experience with flues of the Monier construction, having walls from 1.5 to 2.5 in. thick plastered upon a net-work of iron rods, was unsatisfactory from the standpoint of dura¬bility.

Mar 1, 1905

ALEXANDER, JOHN S, M,'74-6,'81-3 *ASHBURNER, C A, M, '85-7 ASMUS, GEORGE, Dl, '78-80 BACON, D H , M, '00-2 BAYLES, JAMES C , M,'80-2,'91-3 P, '84-5, V,'88-9 BIRKINBINE, JOHN, M, '83-5, V, 'S7-J, P, '91-2 BLAIR, THOMAS S , M, '74-43 BLAKE, WILLIAM P , V,'71-4,'76-7,'05-6 *BLANDY, JOHN F, V,'71-3,'78-9 BLOW, A A, C, '05-7 BOWIE, A J , JR, V,'93-4 *BRAMWELL, J H , A1, '89-91 BROOKS, THOS B , M, '72 BRUNTON, D W , V, 97-8 BUCK, STUART M , M, '83-5 *BURDEN, JAMES A, V,'80-1 BURNHAM, WILLIAM, M, '82-4. CAMPBELL, H H, M, '93-5 CHAMBERLAIN, H S , V, '96-7 CHANNING, J PARKE, V,'08 CHRISTY, S B , V. '91-2, '07-8 CHURCH, JOHN A, M, '79-8l,'94-6, V, '07-8 COGSWELL, W B, V, '74-5,'86-7

Jan 1, 1910

By E. E. ELLIS

THE zinc deposits under development by the Universal Exploration Co., a subsidiary of the United States Steel Corporation, are close to Jefferson City, Tenn., a small town about 30 miles northeast of Knoxville, Tenn., and are served by the Southern Railway. The first zinc mining in this district was in the old Mossy Creek mine at the north edge of the town, opened for oxidized ores in 1871 and later worked for sulfide ores. An oxidized zinc ore deposit (carbonates and silicates) was opened near New Market in 1900 and worked through the war period by the G1'8sselli Chemical Co., producing around 25,000 tons of oxidized ore. In recent years a sulfide deposit has been found and developed but is not producing. About 1% miles south of this a small body of sulfide ore was developed by open cut, but the operation was unsuccessful. The Universal Exploration Co. entered the district in 1926 and, after extensive exploration, has been operating an oxidized ore-body since Janual:y, 1928, and has been developing a sulfide ore body since July, 1928.

Jan 1, 1929

ALEXANDER, JOHN S, M,'74-6,'81-3 ASHBURNER, C A, M, '85-7 ASMUS, GEORGE, Dl, '78-80 BACON, D H , M, '00-2 BAYLES, JAMES C , M,'80-2,'91-3 P, '84-5, V,'88-9 BIRKINBINE, JOHN, M, '83-5, V, 'S7-J, P, '91-2 BLAIR, THOMAS S , M, '74-43 BLAKE, WILLIAM P , V,'71-4,'76-7,'05-6 BLANDY, JOHN F, V,'71-3,'78-9 BLOW, A A, C, '05-7 BOWIE, A J , JR, V,'93-4 BRAMWELL, J H , A1, '89-91 BROOKS, THOS B , M, '72 BRUNTON, D W , V, 97-8 BUCK, STUART M , M, '83-5 BURDEN, JAMES A, V,'80-1 BURNHAM, WILLIAM, M, '82-4. CAMPBELL, H H, M, '93-5 CHAMBERLAIN, H S , V, '96-7 CHANNING, J PARKE, V,'08 CHRISTY, S B , V. '91-2, '07-8 CHURCH, JOHN A, M, '79-8l,'94-6, V, '07-8 COGSWELL, W B, V, '74-5,'86-7

Jan 1, 1910

By George E. Beavers

It is well to understand at once that converter gas is always mixed with copper blast-furnace gas at Copperhill before entering the Glover tower, and, at times, roaster gas is also added along with the converter and blast-furnace gas. Fig. 1 is introduced to show the variations in the sulfur dioxide content of the gas and the ability of the acid-plant operator to control the variations, resulting in a very even grade at the Gay-Lussac tower entrance. The sulfur dioxide content of the gas entering the Gay-Lussac tower must be low and regular to assure low niter consumption. The blast-furnace gas alone is rather uniform as regards sulfur dioxide content and the variations, as shown in Fig. 1, are chiefly caused by converter changes—out for charging, slag pouring, copper pouring, and, of course, the "finish." The combined gas during the converter finish is, at times, almost free of oxygen and the sulfur dioxide content reaches 13.0 per cent. At such times air is added at the Glover tower.

Jan 1, 1934

By V. C. Allen

THE Tri-State Zinc, Inc., Galena, Ill., was confronted with the problem of securing ore from a deposit because the hoisting shaft was several thousand feet from the mill. The orebody is several thousand feet long, averaging 200 ft in width and 60 ft in height and opened up by vertical shafts some 300 ft deep. Mining is by the room-and-pillar method. During the initial operation the ore was loaded by conventional electric 1/2 -yd boom-and-dipper shovels and hauled to the shaft by 8-ton diesel trucks. This underground ore loading and hauling was well adapted to the conditions and productive of low costs per ton. However, with the mill situated as mentioned, a triple handling of all broken rock was necessary: 1-from the stope to the shaft by truck, 2-up the shaft by skip or can into the surface hopper, and 3-by truck from the surface hopper to the crushing plant at the mill. In addition to the repeated handling, serious troubles were encountered during the winter because of freezing in the shaft hopper.

Jan 6, 1951

By K. A. Jackson, J. D. Hunt

A general theory for the growth of lamellar and rod eutectics is presented. These modes of growth depend on the interplay between the diffusion required for phase separation and the formation of interphase boundaries. The present analysis of these factors provides a justification for earlier approximate theovies. The conditions for stability of rod and Lanlellar structures are consitleved in terms of the mechanisms by which the structure can change. The mechanisms considered include both small adjustments to the lnnzellar spacing due to the motion of lamellar faults, and catastrophic changes due to instabilities. It is concluded that stable growth occurs at or near the minimum interface undevcooling for a gizierz growth rate. The conseqrlences of the existence of a diffusion boundary layer at the interface are discussed. The experimental results for the variation of growth rate, undercooling, and Lanzellar spacing are cornpared with the theory. We believe that the theory presented in this paper provides an adequate basis for understanding the complex phenomena of lanzellar and rod eutectic growth. The growth of lamellar eutectics has been the subject of several theoretical and many experimental studies. The foundations for the theoretical work were laid by zenerl and Brandt2 in their analyses of the growth of pearlite. Zener estimated the effect cf diffusion, and took into account the surface energy of the lamellar structure. He found that the lamellar structure could grow in a range of growth rates at a given undercooling provided the lamellar spacing was appropriate for the growth rate. Since pearlite grows with only one growth rate and one lamellar spacing at a given undercooling, there is clearly an ambiguity in the theory. Zener removed this ambiguity by postulating that the growth rate was the maximum possible at the given undercooling. He predicted then that the product of the growth velocity v and the square of the lamellar spacing A should be constant, i.e., A2v = const. Brandt2 started out by assuming that the interface between the lamellae and austenite was sinusoidal. Because of this, the ambiguity encountered by Zener did not arise. Brandt was able to obtain an approximate solution to the diffusion equation, but, since he did not take into account the surface energy, his considerations are incomplete. Tiller3 applied some of these ideas to the growth of eutectics, and proposed a minimum undercooling condition to replace the maximum velocity condition used by Zener. These conditions are formally identical. Hillert4 extended the work of Zener. He found a solution to the diffusion equation assuming the interface to be plane. Taking surface energy into account, and applying Zener's maximum condition, he was able to calculate an approximate shape of the interface. Jackson et al.5 used an iterative method employing an electric analog to the diffusion problem to refine the calculation of interface shape. It was found that the interface shape calculated from a plane-interface solution to the diffusion equation was negligibly different from the exact solution. The method provided an analog only for eutectics for which the volumes of the two phases are equal, growing from a melt of exactly eu-tectic composition. There has also been considerable experimental work on eutectics, Several experimenters8-10 found that A2v is constant as predicted by Zener.1 Hunt and chilton10 demonstrated that ?T/v1/2 is also a constant for the Pb-Sn system as predicted. Lemkey et al.11have recently found A2v to be constant for a rod eutectic. In the present paper, we present the steady-state solution for the diffusion equation for a lamellar eutectic growing with a plane interface, for the general case, that is, with no restriction on the relative volumes of the two phases, and with the melt on or off eutectic composition. A similar solution is also found for a rod-type eutectic. Expressions are obtained for the average composition at the interface and the average curvature of the interface. These equations for the average composition and curvature are similar in form to those derived by Zener1 and Tiller,3 and provide a justification for some of the approximations made by these authors. The mechanisms by which the spacing in a lamellar structure can change are considered. The important mechanism for small changes in lamellar spacing involves a lamellar fault. Examination of the stability of lamellar faults leads to the conclusion that the growth occurs at or near the extremum.* The insta- bilities which can develop in a rodlike structure are also discussed, resulting in the conclusion that this structure also grows at or near the extremum. Comparison of the conditions for rod and lamellar growth permits a prediction of the surface-energy anisotropy required to produce rods or lamellae for various volume-fraction ratios. The diffusion equation predicts the existence of a diffusion boundary layer at the eutectic interface unless the eutectic has 0.5 volume fraction of each phase and is growing into a liquid of eutectic composition. This boundary layer is such as to make the composition in the liquid at the interface approximately equal to the eutectic composition. This boundary layer permits changes in composition during the zone refining of eutectics. Photographs of the eutectic interface of a growing transparent organic eutectic system have been made. Both the components of this eutectic are transparent organic compounds that freeze as metals do.12 The in-

Jan 1, 1967

By Malcolm McColl, C. A. Mead

Thin films (of mica have unique attributes that are exceptionally good for studies of high-field conduction mechamisms in thin-film insulators and the quantum mechanical tunneling of electrons from metal to metal. The principal advantages of using mica films are that the films are crystalline and the cleavage planes occur every 10Å. This property results in films whose thicknesses are integral multiples of 10Å and whose surfaces are uniformly parallel over sizable areas. Hence, very well-defined metal -mica-metal structures are possible. Furthermore, the fact that the insulator is split fro??! a bulk sample allows the index of refraction, dielectric constant, forbidden energy gap, and trapping levels and their density- to be obtained directly from measurements performed on thick samples Of mica rather than requiring that these properties be interred from the conduction characterrsties alone. In the work to he described, all the cleaving was done in a high vacuum just prior to the evaporation of metal elertrodes so as to avoid air contamination at the interfaces. Results of these studies indicate that the current through the 30 and 40Å films exhibited quantitative agreement with the theoretical voltage and temperature dependence derived by Strallon for the tunneling of electrons directly from metal to metal. Thicker films at room temperature exhibited volt-ampere curves suggesting Schottky emission of electrons from the cathode into the conduction band of mica. However, the thermal activation energy was smaller than that found from other measurements, and the experimsntal Schottky dielectric constant was larger than the square of the index of refraction. These facts would indicate that the electrons were being injected into polaron stales ill the iusulator. At low temperatures and high fields, the current through the thicker films did not exhibit the Fowler -Nordheim dependence as would be predicted by a simple extention of the theory of field emission into a vacuum. THE mechanism of electrons tunneling through insulating films has received considerable attention in the last few years due to the devices possible utilizing tunneling'-4 and the success of tunneling in the study of superconductivity.5,6 Until the recent paper by Hartman and chivian7 on the study of aluminum oxide, there had been no reported successful quantitative experimental fit to the theory. Their method of fabrication necessarily results in a polycrystalline insulator, the stoichiometry of which is nonuniform from one side to the other. This structure also introduces complications to the shape of the barrier which is set up by the insulator since the insulator possesses a spatially nonuniform band structure and dielectric constant. Due to these facts an analysis of the data in terms of a pviori barrier shape is of questionable validity. The use of muscovite mica not only overcomes these disadvantages but, as an insulating thin film, provides physical properties (dielectric constant. trapping levels and their densities, forbidden energy gap, and so forth) that are identical to the easily measured values of the bulk sample. Furthermore, it is a single-crystal insulator whose cleavage planes (10Å apart8,9) provide uniformly parallel surfaces of well-known separation. This material is therefore ideally suited to the study of electron-transport phenomena. Von Hippel10 using a 6.5-µ-thick sample was the first to observe the high-field conductivity (=5 x l06 v per cm) of mica. No attempt was made to develop an empirical formula, but Von Hippel concluded from intuitive arguments that the current was being space-charge limited by trapped electrons. Mal'tsev11 in a more recent investigation at high fields observed a dependence of the conductivity a on the field F of the form exp(ßF1/2). This dependence was attributed to the Frenkel effect,12,13 a Schottky type of emission from filled traps. No mention in the English abstract was made of the thicknesses of his samples or, and more important, of how well the value of ß fit Frenkel's theory. In 1962 Foote and Kazan14 developed a technique for splitting mica to a thickness of less than 100Å and observed a dependence of the current density j on the field of the form j = jo exp(ßF1/2) on a thin sample thought to be 40Å thick. Assuming that this was a Schottky emission process and that the appropriate dielectric constant for such a mechanism would be closer to a low-frequency value of 7.6, Foote and Kazan calculated from ß an independent thickness of the mica of 36Å. No further investigation was made of the phenomenon. However, the work reported in this paper indicates that the film measured by Foote and Kazan was probably 60Å thick, the error arising from the measurement of the very small metal-insulator-metal diode areas that were used, along with the diode capacitance and dielectric constant, to calculate the thickness. In the research reported in this paper, Foote and Kazan's technique was modified to cleave muscovite in a vacuum of 10-6 Torr, immediately after which metal electrodes were evaporated creating Au-mica-A1 diodes. Aluminum was chosen because of its strong adhesion to mica, as necessitated by the

Jan 1, 1965

By Frederick F. Frick

SPONGE iron as produced at Anaconda is a fine, -35 mesh, impure product, about 50 pct metallic iron, obtained from the reduction of iron calcine at a temperature of 1850°F by use of coke resulting from slack coal. The metallic iron particles are bulky and spongey and precipitate copper readily and rapidly from a copper sulphate solution. Investigation of the treatment of Greater Butte Project, Kelley, ore at Anaconda early showed the desirability of using sponge iron as a precipitant for the copper in solution resulting from desliming of the ore in a dilute sulphuric acid solution. Anaconda had done considerable work on the production of sponge iron in 1914 for use as a precipitant of copper from leach solutions. Some success and considerable experilence were attained at the time. indicating that, sponge iron might be successfully made by a modification of the process used in 1914, a batch process in which an iron calcine was reduced by means of soft coke, resulting from noncoking coal, in a Bruckner-type revolving horizontal cylindrical furnace widely used 50 years ago. The coke and calcide formed the bed in the Bruckner furnace, which was rotated at about 1 rpm. The bed was brought to a temperature of about 1800°F by means of an oil flame over the surface. Although results were reasonably satisfactory, they did not warrant full development of the process at that time. A good deal of work has been done in the last 50 years on the production of sponge iron. The objective in some cases has been the production of a precipitant for copper from solution, but the bulk of the work has been done for the production of open-hearth steel furnace stock. The production of an open-hearth stock presents two problems rather than one: first, producticon of the sponge iron, and second, what is perhaps of equal difficulty and importance, conversion of the sponge iron into a form suitable for use in the open-hearth furnace. So far as is known to the writer, none of the sponge iron processes tried in the past have proved to be economically feasible. However, Anaconda had a combination of conditions appearing to justify an attempt to produce sponge iron which would serve for the leach-precipitation-float process. It was thought that the process used in 1914, if changed to a continuous one, might work out satisfactorily. The following favorable conditions at Anaconda justified the investigation: 1—A sufficient tonnage of good grade iron calcine resulting from the roasting of a pyrite concentrate in one of the acid plants, at substantially no cost. 2—Reasonably cheap natural gas. 3-—The fact that there was no need for production of a high grade product. 4— The fact that there was no need for obtaining a consistently high reduction of' the iron in calcine. A small revolving Bruckner-type furnace about 2 ft ID by 4 ft long was set up for early pilot work at the research building. This pilot furnace showed that a satisfactory product could be obtained at reasonable cost. It also indicated a marked advantage in preceding the reduction furnace with a furnace of similar size and capacity for preheating and roasting out any residual sulphur from the feed. The small furnace was operated for several months, various details of the process were worked out. and sponge iron was produced to supply a pilot LPF plant which treated 300 lb of Kelley ore pel- hr. Later a second pilot furnace 5 ft in diam and 12 ft long inside was set up at our reverberatory furnace building. This furnace confirmed the data of the small furnace and gave a basis for design of the final plant. At Anaconda a pyrite concentrate, running about 48 pct S, is recovered from copper concentrator tailings by flotation. This concentrate is roasted to sulphur of 3 pct or less at the Chamber acid plant. The iron calcine contains about 57 pct Fe and 18 pct insoluble. The iron calcine feed, as mentioned before, is re-roasted and preheated in a reroast furnace preceding the reduction furnace. Both are of the Bruckner type. The reroasted calcine is fed into the reduction furnace at 800" to 1000°F along with 30 pct slack coal. In the feed end of the furnace the volatile is burned from the slack, giving a soft coke which readily serves for reduction of the iron. Hard metallurgical coke will not serve the purpose. since it does not reduce CO readily at a temperature of 1850°F. All indications are that the actual reduction of the iron is accomplished by carbon monoxide below the surface of the bed, which is 30 in. deep at its center. Apparently there is a constant interchange: Fe²O³ + 3CO = 2Fe - 3CO², CO² + C = 2CO Actually iron oxide is reduced by CO at somewhat lower temperature than the 1850 °F used in the process. but this temperature is necessary to obtain a satisfactory rate of furnace production. The furnace atmosphere is generally reducing, and typical blue carbon monoxide flames satisfactorily cover the bed. Gas flames from four 3-in. Denver Fire Clay Inspirator burners are played directly on the bed, which is slowly cascaded by the 1 rpm of the furnace. An excess of coke is necessary to assure maintenance of good reducing conditions in the furnace bed. Part of this coke is recovered for re-use.

Jan 1, 1954