Search Documents

By T. A. Read, M. W. Burkart

The crystal geometry of the cubic-tetragonal interface after partial transformation of an indium-thallium alloy single crystal is described and a general theory is presented. The effects of applied stresses on this transformation are interpreted and the latent heat of transformation is obtained from observations of transformation under stress. A DIFFUSIONLESS phase transformation between face-centered cubic and face-centered tetragonal structures has been reported for the indium-thallium system by Bowles, Barrett, and Guttman1, 2 The transformation takes place at approximately 105 "C at 18 atomic pct Tl and 25°C at 23 pct Tl. In their study, Bowles, Barrett, and Guttman used poly-crystalline samples whereas in the present study single crystals were used to eliminate the transformation constraints imposed by adjoining grains. The use of single crystals made possible a comprehensive study of the effect of stress on the transformation. In the course of the work, it was possible to formulate a new method of analyzing dif-fusionless transformations (presented in this paper) which permits calculation of the geometry of the interphase interface from a knowledge of the crystal structures of the initial and final phases. The specimens were prepared from chemically pure thallium and 99.97 pct In which were weighed out to produce 3 to 4 grams of alloy of the desired concentration. The metal was placed in clean fused silica tubing, then melted, degassed and sealed under vacuum. (To obtain single crystals, it was found that both degassing and extreme cleanliness were essential.) Single-crystal specimens were grown by a modified Bridgman technique.8 pecimens were removed from the tube by dissolving the quartz in concentrated hydrofluoric acid which attacks the specimen very slowly. The specimen then was polished mechanically to produce four flat surfaces, electropolished, and annealed at 140°C for 48 hr. The electropolishing solution used was that described by Bowles, Barrett, and Guttman and the polishing was carried out on both the high and low temperature phases of the alloy. The high temperature polishing was done at 110°C with a stainless steel cathode. Visual Observation of the Transformation in Single Crystals A visual study of the transformation was made on specimens which had been electropolished in the high temperature phase. The specimens were supported on the stage of a metallograph by an electrically heated holder which contained an opening for observing the specimen. Visual evidence of transformation was found in the presence of an interface which separated the two phases. The interface plane defines the boundary of the phase undergoing transformation and manifests itself by the sharp change in angle between the surface of the specimen and the incident light at the juncture of the two phases. On slow cooling, well-annealed specimens transformed from the face-centered cubic structure to the face-centered tetragonal structure by the motion of a single plane interface which traversed the specimen from one end to the other. Upon heating, the interface moved back in the reverse direction. The interface could be started, stopped, or reversed at will. A temperature hysteresis of about 31/2oC was observed in the reversal of the interface. Holding an interface stationary caused it to disappear completely in most cases, whereas in other instances the interface became less distinct depending upon its orientation. The interface could be made to reappear by changing the temperature of the specimen. The low temperature tetragonal structure exhibits only the fine markings or subbands reported by Bowles, Barrett, and Guttman and is illustrated in Fig. 1. These subbands are twin-related. Back-reflection Laue patterns show the breakup of the cubic spots into pairs of spots corresponding to the twin orientations of the tetragonal phase.

Jan 1, 1954

By L. D. Jaffe

From data found in the literature, a method has been derived for calculating hardenability of titanium alloys from their composition. A single graph gives the contributions of each alloying element. These are simply added to a base hardenability for unalloyed titanium. Results agree satisfactorily with measured harden-abilities. RECENTLY the importance of hardenability of titanium alloys in permitting attainment of high strength and hardness has become apparent. If a titanium-base alloy has adequate hardenability for the section size and quenching practice used, it can generally be heat treated to high strength and hardness either by simple quenching or cooling from temperatures near the ß transus, by quenching and tempering (aging), or perhaps by direct isothermal transformation of ß1,2 If the hardenability is inadequate, high strength cannot be attained. Preliminary charts translating hardenability requirements for shapes quenched in various media into terms of Jominy end quenched hardenability specimens or ideal round sizes are now available for titanium alloys." The method proposed in 1942 by M. A. Grossmann for calculating hardenability of steels from composition has proved to be of great practical value.' It appeared worthwhile to see whether, using information available in the literature, a corresponding method for calculating hardenability of titanium-base alloys could be derived. Data No systematic experimental study of the hardenability of titanium-base alloys has yet been made. There is available, however, a considerable quantity of scattered data bearing on hardenability. Some investigators determined Jominy curves on one or several alloys. Others reported as-quenched hardness for specimens of a few alloys cooled at various rates or in various media. Still others gave the as-quenched hardness for systematically varied composition, using one or several cooling mediums. The measurements utilized in this work were limited to hardness. Strength measurements were not used because a low strength may reflect high hardness combined with brittleness. Since, in general, the hardness of titanium alloys goes through a peak as the cooling rate is varied from extremely fast to extremely slow, the cooling conditions at which peak hardness was found were taken as the measure of hardenability.1,2 When as-quenched hardness was found to drop as the content of an alloying element (believed to increase hardenability) was raised, this was taken as an indication that the cooling rate was faster than that giving peak hardness; otherwise, the hardness should go up because of solid solution hardening. Also, if the hardness increased on tempering at low temperatures, this was again taken to indicate that the cooling rate had been faster than that giving peak hardness. Many of the data did not indicate precisely the cooling conditions for peak hardness but merely set a maximum or a minimum bound, or a bracket. Since the sizes of specimens quenched and the location of the hardness readings were not always given, it was occasionally necessary to estimate reasonable limits for them. Only the nominal compositions were available in some cases. As quenching from below the ß transus is equivalent to starting with a mixture of a and ß phases, whose individual composition would differ from the overall composition of the alloy, only measurements after quenches from above the ß transus were used. Hardness measurements on samples heated during metal-lographic mounting were also discarded. Because of their bulk, the data used will not be reproduced. They have been or will be published elsewhere.5-22 Approach All data were first translated into terms of ideal round size. For conversion from Jominy or quenched round or sheet, the author's graphs were used." For a few furnace cools or helium quenches where cooling rates were given, conversion was made on the basis of equal cooling coefficient.23 Plots of ideal round size for peak hardness against percentage of alloying element were next made for

Jan 1, 1956

By Irving B. Cadoff, Ernest Levine

The crack formation and propagation in the single -phase Cu-4 pct Ag alloys were studied. The alloys were loaded in mercury to various stress levels, the mercury was removed, and the specimen examined for cracks. Cracks were found to develop below the fracture stress; the frequency of such cracks increased with increasing stress level. Some cracks were nmpropagative. Fracture in mercury was found to occur by the link-up of cracks formed at various stress levels rather than by the growth and propagation of a single crack. If the mercury environment is removed prior to a critical amount of crack formation, then continued loading results in ductile fracture. The appearance of the cracks at selected grain boundaries is related to the relative orientation of the boundaries, as are the propaga-tive characteristics of the crack. The mercury interaction appears to be one of lowering the strength of the metal-metal bonds in the high-stress area of the grain boundary. GRIFFITH'S microcrack theory1 proposed a critical crack size above which a crack in an elastic material grows with decreasing energy at a stress of From his theory it was proposed that the presence of a liquid tends to lower the surface energy of the microcrack faces2 leading to a decrease in the critical crack size necessary for spontaneous fracture propagation. stroh3 proposed that the stress concentration at a grain boundary due to pile-up may initiate a microcrack at the grain boundary. petch4 and Stroh5 evaluated the stress distribution at the head of a pile-up in a polycrystal-line material and deduced that the critical crack size and hence of is dependent on the grain size. Experimental verification of this dependence was found by petch6 for hydrogen embrittlement of steel. Studies in stress-corrosion cracking7 have provided a picture of fracture which shows that initial separations occur in a scattered, independent fashion in regions of high tensile stress. A minimum or threshold stress is necessary to produce a sufficient stress concentration to initiate frac- ture. These separations join up to form a crack. The extension of fracture is largely discontinuous and consists of a joining up of cracks. In recent worka evidence of this scattered crack network was found in a Cu-Ag alloy embrittled by mercury. For the Cu alloy-Hg couple, the crack path has also been found to be dependent on the orientation of adjacent grains, and with the addition of zinc to mercury a reduction in embrittlement along with a change in fracture morphology was found.9 In this present study, a mercury-dewetting method was used to observe crack initiation and fracture morphology when a Cu-4 pct Ag alloy is deformed in mercury and Hg-Zn solutions. PROCEDURE Specimens of Cu-4 pct Ag were prepared as in previous crack-path studies.' The specimens were heated at 770°C for 24 hr and water-quenched Tension tests using a table-model Instron were carried out in mercury and in various concentrations of Hg-Zn. Loading was in steps up to the fracture stress, with the load being removed and the specimen examined for surface cracks at each step. The specimens were dewetted after each load to permit examination of the surface structure and rewetted prior to continued loading. The specimens were wetted by electro polish ing in phosphoric acid, rinsing in alcohol, and then immersing in a pool of mercury. Dewetting was accomplished by flame heating the specimen for 30 sec in a vacuum. Some surface contamination was found, but not enough to obscure crack configurations and grain boundaries. RESULTS Fracture Characteristics in Mercury. Fig. 1 is a stress-strain curve showing the progressive step-wise loading of the specimen. As may be seen from the graph, the first position stopped at a is at a stress 5000 psi below the expected fracture stress of 25,000 psi. Examination of the specimen after removal of mercury showed only one crack. The appearance of this crack at a stress far below the fracture stress of this alloy in mercury did not affect the stress-strain curve in any manner. The specimen was then recoated with mercury and deformation was continued (curve b, Fig. 1) raising the stress by 4000 psi, and the same procedure re~eated. The initial crack was located and appeared as in Fig. 2 (crack lb). In this figure the crack is

Jan 1, 1964

By D. R. Parrish, K. W. Beaver, H. W. Wood, R. W. Rausch

A pilot test of forward combustion in the Shannon pool, Salt Creek field, Wyo., is described. The Shannon sand, 950-ft deep, contains a heavy (25" API), viscous (76 cp) oil. Natural reservoir energy is limited. Primary production, intermittent since 1889, recovered only about 2 per cent of the oil in place. The field is operated by Pan American Petroleum Corp. for the Midwest Oil Corp., the owner. The original pilot was a 1.32-acre five-spot. The expanded pilot has eight producing wells surrounding a roughly triangular area of about five acres with the injection well near the center. A control or comparison well was also recompleted in another part of the field. Operation of the pilot has been little different front an ordinary gas drive. Little special equipment was found to be absolutely necessary. Except for some use of a temperature-resistant cement, all wells were conventionally completed. In spite of poor oxygen consumption, the over-all performance of the pilot has been good. Total oil recovery to June 1, 1961, was 73,971 bbl. The wells of the original pilot alone had produced about 24,000 bbl, equivalent to 50 per cent of the oil in place, when fire breakthrough at the first well occurred. These wells have now produced oil equivalent to more than 74 per cent of the oil in place in the original pilot area and production is continuing. It appears that ultimate recovery will approach theoretical maximums before the wells must be abandoned. Performance of the pilot has been encouraging, and expansion to a fieldwide combustion operation is being investigated. INTRODUCTION The results of both laboratory investigations and field tests of underground combustion have been reported previously.' However, most of the field tests were primarily experimental. More information and experience are needed before forward-combustion operations can be engineered with confidence. The purpose of this paper is to present the results of a successful pilot test of forward combustion. These re- sults should increase confidence in forward combustion as a practical method for commercial oil recovery. HISTORY OF THE SHANNON POOL The Shannon pool is located on the north end of the Salt Creek field in Natrona County, Wyo. It is approximately 50-miles north of the city of Casper. The Shannon pool's3 discovery well was completed in 1889, making this one of the oldest oil fields in the Rocky Mountain region. Three more wells were drilled in 1890. First production was hauled in wooden barrels by horse and wagon to the railroad in Casper. In 1894 a small refinery, the first in Wyoming, was built in Casper to process the Shannon crude. In the following years the field changed hands several times. It appears that each new owner did some development drilling as several wells were completed in each of the years 1895, 1902, 1905 and 1912, with negligible development in the intervening years. Forty-eight wells were drilled in this period, but many were later abandoned. Discovery of the more prolific Salt Creek field proper ultimately forced suspension of operations at the Shannon pool. After 1915 there was only sporadic production, mostly to supply cheap boiler fuel to drilling rigs in the Salt Creek field. But even this was discontinued in 1931. Since then the pool had been dormant until the recent operations, which are the subject of this paper. The Shannon pool is now owned by the Midwest Oil Corp. Field operations are conducted for Midwest by Pan American Petroleum Corp. THE RESERVOIR Fig. 1 is a map showing subsurface contours of the Shannon pool. The reservoir is on a nose of the Salt Creek anticline dipping to the north at about 500 ft/mile. The trap is provided by a shallow fault on the updip side of the productive area. The downdip limits are bounded by water, but this water has not provided an effective source of reservoir energy. The Shannon sand outcrops at many places in the immediate vicinity, providing good surface indications of the Salt Creek anticline. At the Shannon pool the sand has been lowered by faulting and is overlain by about 900 ft of shale and other sands. The Shannon sand consists of two members. The upper, a water sand, is about 40-ft thick and is separated from the lower member by several feet of sandy shale. The oil pay occurs in the lower mem-

By M. Shelef, A. W. Fletcher

The effect of alkali sulfates in promoting the sul-fation of nickel and copper in a bulk sulfide flota -tion concentrate by fluidized bed roasting has been studied in the laboratory, and it was shown that the various alkali sulfates promote sulfation to approximately the same extent. The sulfation of a mixture of synthetically prepared iron and nickel oxide and of nickel ferrite has also been studied. Nickel sulfation was promoted by high ratios of Fe:Ni and by the presence of sodium sulfate. THE work described in this paper was a continuation of earlier studies into the role of alkali sulfates in promoting the sulfation roasting of nickel sulfides1,2 in an endeavor to determine how the system was affected by the presence of compounds of iron and copper. The earlier work1 showed that, in the sulfation of NiO at 680°C, the reaction was limited by the formation of an impermeable film of nickel sulfate on the oxide surface. The relative effect of the various alkali sulfates in promoting nickel sulfation varied in the order: Li > Na >Cs > Rb > K A study of alkali sulfate/ nickel sulfate interactions at high temperatures showed that the promoting action was due to the fact that the nickel sulfate product layer sintered and agglomerated only when the more active additives were present. This resulted in the formation of discontinuities in the nickel sulfate layer so that diffusion of the sulfating gases to the NiO surface was no longer impeded and the reaction could proceed to completion. A similar explanation was used for the observation that sodium and lithium sulfates promote the oxidation of NiS to NiO at temperatures below 750°C since small amounts of nickel sulfate were formed during oxidation.2 It was of interest to study the effect of alkali sulfates on the sulfate roasting of a sulfide flotation concentrate which is typical of material treated commercially. In order to control temperature it is essential to roast sulfides in a fluidized bed and this technique was therefore used, although the batchwise operation of a small-scale laboratory reactor does not reproduce all conditions which prevail in full-scale continuous plant. The results obtained are therefore only comparative, and cannot be used for predicting the optimum conditions for metal extraction. The sulfation of synthetically prepared mixed oxides of nickel + copper and nickel + iron and of nickel ferrite was also studied to evaluate the relative effects of alkali sulfates with more complex systems. SULFATION ROASTING OF A SULFIDE FLOTATION CONCENTRATE The bulk sulfide flotation concentrate used in this work contained 7.92 pct Ni, 1.74 pct Cu, 35.66 pct Fe, and 31.28 pct S. The sulfide minerals present in order of abundance were pyrrhotite FeS, pyrite FeS2, pentlandite (FeNi)S, and chalcopyrite CuFeS2. Two samples described as coarse and fine were used. The coarse sample, which was a flotation concentrate (58 pct plus 300 mesh), was ground to 100 pct minus 350 mesh to produce the fine sample. Before roasting, the sample of sulfide concentrate was agglomerated by wetting witli a solution of the alkali sulfate (or water), thoroughly mixing, and drying at 110°C. This gave a cake which was gently crushed and screened, the -18 +100 mesh fraction being used for fluidized bed roasting. A similar-size fraction had been used by the authors in pilot plant work with a 4-in.-diam fluidized bed reactor.' In this work it was found that the molar ratio of additive to the total iron + nickel + copper content of the sulfide sample should be adjusted to a value of approximately 0.06, as this was the optimum amount necessary for nickel sulfation. Experimental. The fluidized bed reactor consisted of a quartz tube approximately 60 cm long and 30 mm in diameter resting in a vertical tube furnace. The sulfide bed (30 g) was supported on a bed of -4 +12 mesh quartz particles 3 cm high, which rested on a sintered quartz disc welded to the tube. The temperature of the furnace was controlled with a variable transformer to give a final bed temperature of 680°C. The bed was fluidized with air or mixtures of air + 10 pct v/v SO2, at a total apparent gas velocity of 60 to 65 cm per sec at 680°C. The SO2 was introduced into the fluidizing air stream only when the oxidation of the sulfides was completed. At the end of the roasting period the calcine was leached with boiling water and the

Jan 1, 1964

By W. C. Smith, P. J. Hickey

After a short historical background of the process evolution, this article descvibes present-day plant facilities and operating techniques utilized for high-purity bismuth production. The plant is one of the world's largest, with an annual output of some one million pounds of refined bismutlz. PREVIOUS papers1 written by staff members of Cerro de Pasco Corp. have referred briefly to the production of refined bismuth. Since the Corporation is one of the world's foremost producers of high-purity bismuth, a detailed description of the process for extracting the metal may be of general interest. Following a short historical background of the development of the actual process, this presentation will trace the progress of bismuth from its entry into the primary smelting circuits to its concentration in electrolytic lead cell slimes. Our facilities for the treatment of anode muds will be described and the extractive methods given in some detail, with particular emphasis on the techniques which result in the production of refined metal. HISTORICAL BACKGROUND Shortly after Cerro de Pasco began smelting operations at Oroya, Peru in 1922, it became apparent that the dust carried by copper converter gas contained appreciable amounts of bismuth. Although dust collection efficiency was poor prior to building of the 550-ft stack and installation of the central cottrells in 1938, a large stock of dust was accumulated during the intervening years, having the following approximate composition: Oz. per ton Ag - 11.0 Pct Sn — 0.5 Pct Pb - 49.0 Pct Zn - 6.5 Pct Bi - 2.0 Pct Insol. - 1.5 Pct Cu - 0.7 Pct Fe - 2.3 Pct Sb - 3.0 Pct S - 10.0 Pct As - 7.5 In the mid-1920's, experimental crucible melts of this dust with carbon indicated that most of the bismuth and silver, and some of the lead, could be reduced to a fairly clean bullion. Other products were a small amount of leady copper matte and a slag high in zinc, arsenic, antimony, and lead; this slag contained some tin but only small quantities of silver, bismuth, and copper. After the laboratory results had been confirmed by operation of a small reverberatory, a dust reduction furnace was constructed. The ±10 pct Bi-Pb bullion produced from this operation was stocked until 1930, when an Oroya-designed converter type furnace3 was installed for the elimination of arsenic, antimony, and some lead from the bullion. This process concentrated the bismuth from 10 to about 60 pct. By means of the bismuth process developed4 by W. C. Smith at East Chicago (1909-1914) and the discovery of a method5 for separation of lead from bismuth with chlorine gas in 1929, it became possible to begin production of refined bismuth. Unfortunately, bismuth deleaded with chlorine always contained residual chlorides, and the removal of the chlorides by caustic soda left a lead content of 0.02 to 0.04 pct. This final problem was solved6 by substitution of air-blowing for the caustic treatment, which effectively removed all excess chlorine and gave bismuth which was practically lead-free. In 1934, a pilot electrolytic lead refinery began operations at Oroya. Lead smelting was resumed in 1935 and two years later a 100-ton-per-day lead refinery was put into service. In conjunction with the latter, the present-day Anode Residue Plant was constructed. Until 1940, the plant treated both lead anode slimes and dust reduction bullion. The dust reduction furnace was shut down in that year, and all cottrell dusts (with the exception of the product from the arsenic cottrell) were mixed with pyrite and treated in a Wedge roaster to eliminate all possible arsenic. Calcine from this operation joined the sinter plant feed; hence the bismuth from the copper and lead circuits was collected in the lead bullion and subsequently in lead anode slimes from the electrolytic lead refinery. The latter source has been the only bismuth-bearing material of any consequence entering the Anode Residue Plant from late 1940 to the present. A copper refinery began operating in 1948, and the cell mud from this plant is mixed with lead slimes and processed through the same circuit, though only a small quantity of bismuth is present in electrolytic copper cell residues. BISMUTH INTAKE Present-day routes which are followed by the new bismuth feed from its entry into the primary smelting circuits to its arrival at the Anode Residue Plant are traced schematically in Fig. 1. As illus-

Jan 1, 1962

By Reaves. M. J.

The title of my talk, "What Happened to the Uranium Boom?" is old news. Certainly it is for this group. All of us that make our living in uranium know that the boom of the last half of the 1970's is over. U.S. production has been exceeding consumption by more than two to one. Mines and mills are closing and yellowcake prices have been dropping for over 20 months. The gloomy outlook for the industry in the near term has been well documented by soothsayers of various descriptions, your daily newspapers, and in the Nuexco Monthly Reports. I'd like to attempt to describe the next upturn in the market (speculate, really) based upon the clues we're seeing now. In order to do that, I'd first like to go over briefly, some of the market factors that contributed to the recent price drop and resultant production cutbacks, and then hypothesize on the way these factors are changing and will change. Market prices are greatly affected (maybe even entirely determined) by buyer perceptions. This is particularly true with uranium, because of the long lead times associated with nuclear plant construction and also with conventional mine/mill development. Before the price rise (say, 1975) utility uranium buyers believed that: 1) U.S. producers would have difficulty expanding to meet U.S. demand. 2) Australian and Canadian production was essential to avoid shortages in the early 1980's. 3) Uranlum prices would continue to rise as demand exceeded supply. 4) Enrichment capacity would become inadequate. It was thought necessary, therefore, to build enriched inventory in the early 1980's for use in the late 1980's. Artificially accelerated expansion of the uranium producer industry was necessary to accommodate anticipated enrichment demand. Current perceptions are largely the opposite. These are the beliefs that were held most of this year and late last year as prices dropped. 1) U.S. production is far in excess of domestic need. Contraction of the U.S. production lndustry is necessary. 2) Canadian and Australian supply is optional and not essential. Producers in those countries are expanding mainly by displacing higher cost production and not because they fill a void, 3) Prices may be essentially stable for some time. 4) Enriched uranium is in excess supply. That is 1981. 1982 is shaping up to look like this: 1) Prices will have bottomed out. (That is not Nuexco's opinion necessarily, by the way, but it is my opinion.) 2) There will still be substantial utility inventories, but fewer spot sales. 3) Canadian and perhaps Australian sellers will have made substantial sales in the U.S. and will be aggressively seeking more. 4) U.S. production will have been dramatically curtailed. U.S. utilities that wish to con- tract long term will have difficulty in finding domestic sellers. Concern will develop about the availability of U.S. production capability. Virtually all long term con- tracts signed will be with non-U.S. sellers. 5) An awareness will begin to develop among U.S. buyers that we are approaching a period of dependence upon foreign uranium (which will be true). The history of the uranium market has been one of dramatic changes and overreaction to those changes. The rapid price rise of a few years ago generated excess U.S. production capacity and the rapid price drop of the last two years will almost certainly result in too little capacity. It will soon be difficult for U.S. buyers to buy domestic material except on the spot market. The question is, "will they care?" The lack of demand, of course, is the underlying reason for the current poor health of the uranium industry. In 1972, 1973 and 1974 collectively, there were 105 nuclear reactors ordered in the U.S. That ordering rate was expected to continue and accelerate throughout this century. In 1975, 1976, 1977, 1978, 1979, and 1980 altogether, there were 56 more reactors cancelled than ordered. The net growth of our only customer since 1974 has been a negative 56. TO put this in perspective, if these 56 reactors were operating now it would more than double present U.S. uranium consumption. Underlying lack of demand is something that is simply not going to change in this decade. Time is going to be required. The NRC indicates that the maximum feasible number of new reactors that can be licensed each year is six. That would increase uranium consumption by only 10% per year. New reactors, if ordered tomorrow, would not generate new uranium demand until after 1990. Even so, United States' consumption of uranium will rise from the 1980 level of 18 million pounds per year, to

Jan 1, 1982

By W. C. Hauber

Techniques previously published to predict the production performance of a water flood when the mobility ratio is not unity have been primarily restricted to a five-spot well pattern. When other types of well patterns are considered, the prediction of performance has required either a model study or a complex numerical solution of a multiple-fluid system with a high-speed digital computer. Simple methods are developed in this report for predicting the areal sweep efficiency and injectivity history of a water flood for arbitrary well patterns and mobility ratios. The effect of an initial gas saturation can be incorporated into this method of prediction. With the layer superposition concepts published by Prats, et al.,1 these methods can be used to predict the production performance of a water flood in a reservoir having a wide range in permeability. A reasonably good agreement is shown by comparisons of the results calculated by this method with those obtained either by model studies or by complex numerical solution of multiple-fluid systems. Therefore, it has been concluded that a reasonably accurate method has been developed for predicting the production performance of a water flood employing an arbitrary type of well pattern for any given mobility ratio. A medium-speed digital computer can be used in applying this method. INTRODUCTION Production performance of multi-fluid five-spot water floods can be predicted by the techniques published by Prats, et al.1 This technique takes into account the effects of initial gas saturation, mobility ratio and vertical variations in horizontal permeability. A basic assumption in applying this technique is that unit displacement efficiency does not vary with time after the passage of the flood front. Prats, et al. demonstrated that this assumption is valid for normal waterflood applications with small mobility ratios. To extend Prats' technique to other types of well patterns has required either an experimental model study or a numerical solution of a multiple-fluid system to describe the performance of an individual homogeneous layer. Sheldon and Dougherty2 presented an exact numerical solution employing any arbitrary well pattern. This technique is complex to apply, requiring (1) numerical solution of the single-fluid system, (2) conformal mapping of the streamlines and iso-potential lines to form a new grid network, and (3) a numerical solution of the multi-fluid system on the new grid network. A method was developed in this paper to approximate areal sweep efficiency and injectivity as functions of time for an individual homogeneous layer for arbitrary well patterns and mobility ratios. Analytic expressions were derived to directly apply this method to five-spot and direct line drive well patterns. For other types of well patterns, this method is similar to the approach of Higgids and Leighton,6 in that it utilizes the stream tubes and iso-potential lines obtained by the solution of differential equations when the mobility ratio is unity. However, this method is easier to apply than the Higgins-Leighton method since it does not require knowledge of the variation between oil and water relative permeabilities and saturation. Using the relationship between areal sweep efficiency, injectivity and the volume of water injected into an individual homogeneous layer as obtained by the method presented in this paper, and Prats' technique for the superposition of individual layers, one can predict the production performance of any water flood. ASSUMPTIONS GENERAL Basic assumptions made in this report are that fluids are incompressible and the layers are horizontal, homogeneous and uniformly thick. It is assumed that as water is injected into the layer, three distinct regions are formed —a water bank, an oil bank, and an unflooded region. Each region is assumed to displace other regions in a pis-tonlike manner, with only one fluid flowing in each region, so that there is no change in unit displacement efficiency with time after the flood front has passed in the reservoir. Therefore, the residual oil saturation in the water bank and the oil saturations in the unflooded region are constant throughout the layer. The ratio (F) of the bulk volume of a layer occupied by the oil and water banks at any time before oil breakthrough, to the corresponding bulk volume of a layer occupied by the water bank, is given' by the equation BREAKTHROUGH AREAL SWEEP EFFICIENCY To predict the behavior of any type of waterflood pattern, one must know the breakthrough areal sweep efficiency Eb(Mc,o, F) for the pattern for any water:oil mo-

Jan 1, 1965

By R. A. Garling

INTRODUCTION Since the infancy of in situ uranium mining, a growing number of hydrometallurgical processes have been incorporated into pilot and commercial scale flowsheets. Although initial design efforts were geared toward maximizing uranium recovery and minimizing plant and wellfield flow circuit maintenance, recent emphasis has shifted to improved means of water conservation and aquifer restoration. As mining units approached depletion, evaporation ponds reached minimum freeboard, and state and federal agencies demanded proof of groundwater restoration, processes including mixed bed and conventional ion exchange, reverse osmosis and electrodialysis were adopted by the industry. These units served the additional function of reducing process bleed flows during mining in states where the deep disposal well permitting ice remains unbroken. This report concerns the use of electrodialysis as an alternative to the more conventional processes used in in situ mining. In addition to a brief history and description of the process, a comparison to reverse osmosis and operational data derived from testing an Ionics, Inc. 1.31 x 10-3 m /s (30,000 gallon/day) unit at the Teton-Nedco Leuenberger Research and Development pilot will be presented. HISTORY Commercially practicable electrodialysis was contingent upon the development of synthetic ion exchange membranes in 1940's. In 1952, Ionics Inc. demonstrated that the process was amenable to the treatment of salt and brackish water and, in 1954, made their first commercial sale. The following decade saw several major electrodialysis unit sales which were generally targeted for use on private or municipal potable water treatment. Major increases in membrane desalting unit capacities, facilitated by technological advances in the reserve osmosis industry, were noted during the 1970's. The development of polarity reversing electrodialysis equipment which reduced feed pretreatment requirements, increased water recovery rates, and simplified unit operation, kept Ionics Inc. competetive in the water treatment industry. Engineering advances which incorporated automated equipment, non-corrosive construction materials, and improved ion exchange membranes allowed the electrodialysis process to compete in industrial waste treatment among other commercial markets. PROCESS AND APPARATUS DESCRIPTION The electrodialysis process utilizes direct electrical current passed across a stack of alternating cation and anion selective membranes in order to achieve an electrochemical separation of ionized materials in an aqueous solution. The membrane stack has the appearance of a plate and frame filter press and auxilliary equipment includes solution pumps, electrically actuated valves, filters, piping and a direct current power source. The ion separation membranes are thin sheets of synthetic cation or anion selective resins. Attaching sulfonate or quaternary ammonium groups to the cross linked copolymer structure determines the ion selectivity of the membrane. The membranes are separated from each other in the stack by non-conductive spacers that house flow channels which route the flow tortuously and parallel to the membranes. Direct electrical current passing perpendicularly to the membranes and solution passages attracts cations toward the cathode and anions toward the anode (Figure 1). As the ions from the feed stream pass through the ion selective membranes, they become concentrated in the adjacent brine channel and are retained there by the combined attractive force of the electrode and the repelling force of the next membrane toward the electrode. Limiting factors on the degree of demineralization possible include chemical solubilities in the brine flow and the current density that will produce an unacceptable degree of polarization (Figure 1). Feed or brine solution treatment with complexing agents or acids has been successfully applied to prevent membrane scaling. Polarization can occur when sufficient current density is applied to dissociate water in the ion depleted region of the diluting compartments near the membrane surfaces. Significant polarization is evidenced by large electrical resistances across cell pairs and notable pH differences between diluting and concentrating streams. Limiting current densities have been increased in U.S. manufactured equipment by utilizing tortuous flow paths of relatively high linear velocities thereby promoting continous solution mixing. Energy consumption is due to separating electrolytes and solutions, oxidation and reduction reactions occurring in electrode compartments, overcoming electrical resistance, conversion from AC to DC power, solution pumping and auxiliary equipment actuation. A major improvement to the basic electrodialysis process was applied in 1970 which resulted in frequent, automatic cleaning and descaling of membrane surfaces. The process, polarity reversal, incorporates alternating the cathode and anode on a periodic basis while exchanging product and brine flow channels via electrically actuated values. The reversal reduces the potential of stack plugging with CaCO3 (calcite), CaSO4 (gypsum), and colloidal materials and, in most waters, eliminates feed pre-treatment requirements. For approximately two minutes during and following the reversal, off spec. water is flushed to waste or reintroduced to the feed supply. The usual feed treatment on polarity reversing electro-

Jan 1, 1982

By J. Chipman, G. G. Hatch

T. ROSENQVIST*—It is a pleasure to see the excellent way in which the experimental part of this work has been handled. There seems to be little doubt that the distribution data obtained corresponds most closely to thermodynamic equilibrium under the prevailing reducing conditions, namely equilibrium with graphite and one atmosphere CO pressure. The desulphurization curves in Fig 10 show the same general feature as the curves given by Holbrook and Joseph, but the distribution ratios are from 20 to 40 times greater—undoubtedly due to a closer approach to true equilibrium. In the theoretical discussion, the authors calculate a theoretical distribution (S) ration -jg-. which they find to be about 50 times greater than the experimental. The deviation is so great that the basis for their calculation needs a more thorough examination. The authors base their thermodynamic calculation on free energy expressions where diluted solutions of FeS and CaS are used as standard states. (The activity coefficient in diluted solutions is taken to equal unity.) Such a standard state will change when the nature of the solvent is changed. Taking the free energy of the reaction [FeS] ? (FeS), Eq 2, which is derived from the distribution of sulphur between an iron and a FeO-melt, it is very unlikely that the free energy of this reaction will be the same for a distribution between pig iron and a calcium silicate slag. Therefore a more fundamental basis for the thermodyuamic calculations seems needed, where all thermodynamic equations are referred to unambiguously defined standard states. The most natural standard states for CaO and CaS are the pure solid substances at the same temperature. As standard state for sulphur in iron, pure liquid FeS can be used. This rules out Eq 2 [FeS] ;=s (FeS) because ?F° = 0. The standard equation will then be: FeS, + CaO6 + Cgraph ?Fei + CaS8 + CO. vFo1773 = 25,000 cal It would be more universal and also simpler to refer the escaping tendency of sulphur in liquid iron to the corresponding H2S/H2 ratio which can readily be determined experimentally. As standard state a gas mixture H2S/H2 = 1/1 can be used. (This corresponds at the temperature of liquid iron closely to one atmosphere S2 vapor.) Thus the standard equation for the sulphur reaction can be formulated as follows: H2S0 + CaO3 + Cgraph ?H2o + CaS8 + COg The standard free energy of this reaction has been calculated from the best available data to AF°m3 = —35,000 cal. This gives for the equilibrium constant at 1500°C Now, the solubility of CaS in blast furnace slags has been determined by McCafferey and Oesterle* and corresponds at 1500°C to about 10 pet S (varying somewhat with the composition of the slag.) If the activity of CaS is assumed linear between 0-10 pet as curve 1, (see Fig 11), then acaO = 0.1 (S); (S) being wt. pet sulphur in the slag. For a diluted solution of sulphur in an iron melt saturated with carbon, the ratio H2S/H2 is, according to Kitchener, Bockris and Liberman,f about 0.01 [S], [S] being wt. pet sulphur in iron. Substituting these values in the expression for Kp we find The value 2.103 is only 4 times greater than the experimental coefficient found by Hatch and Chipman, but the value is very sensitive to a small error in AF°. A better agreement with the experimental distribution coefficient can be obtained if one assumes the activity of CaS to run like curve 2 (Fig 11). This (S) will give a lower theoretical W, value, a value which varies with (S) exactly as Hatch and Chipman learned. Such a shape of the activity curve, which corresponds to a positive deviation from Raoult's law, is actually to be expected from the fact that liquid silicate and sulphide phases usually show incomplete miscibility. A closer agreement between experimental and theoretical data can not be expected before we have more complete data for the individual activities of CaS and CaO in the slag. The activities acaS and Ocao referred to the solid phases as standard states, are exact defined quantities contrary to the somewhat undefined expression "free lime," and they are independent of any theory for the constitution of liquid slag. J. CHIPMAN (authors' reply)—The authors wish to thank Mr. Rosenqvist for his very interesting and useful thermodynamic addition. Curve 2 of his figure offers the needed basis for explaining the increase in the ratio (S)/[S] with increasing sulphur content. Attention is called to an error in the printed paper: Fig 2 and 3 are reversed. M. TENENBAUM*—In the figures showing the relationship between excess base and sulphur distribution (Fig 6, 7 and 9) the slope of the curve tapers off in the negative basicity range. Somewhat the same thing is observed with open hearth slags. In that case, the fact that some sulphur distribution between slag and metal is obtained with negative basicity is interpreted as indicating some dissociation of the lime silicate compounds whose existence in oxidizing basic slags has been used to explain various observed phenomena with regard to other slag-metal reactions. In the case of the blast furnace slags, the reduced slope of the sulphur distribution curve with decreasing excess base is attributed to the amphoteric effect of alumina. Has the possibility of other explanations been investigated ?

Jan 1, 1950

By C. Wert, G. Mah

A relaxation peak thought to be due to the presence of C-C pairs in cobalt has been observed. It exists both above 420"C, where cobalt has the fcc structure, and below 420"C, where cobalt has the hcp structure at equilibrium. The effect is thought, however, to be caused by motion of C-C pairs in the fcc phase in both instances; enough retained fcc phase was deduced to be present at temperatures below 420°C to make the phenomenon possible. Measurements of the aniso-tropy of the effect in single crystals of various orientations of fcc phase showed the effect to have a maximum value in longitudinal strain for a [loo] crystal and a minimum value for a [Ill] crystal. This observation seems to rule out the possibility of (110) nn pairs being responsible for the effect. From measurements of the strength of the relaxation in the alloys, we reach the conclusion that both the binding energy of the pairs and the specific relaxation per pair are smaller than corresponding quantities for interstitial pairs in bcc metals. DETERMINATION of the details of atom placement of small atoms such as carbon, nitrogen, oxygen, and hydrogen in metals has been a difficult problem. In certain alloys such as martensite extensive departure from random placement of the interstitials can be deduced from X-ray diffraction off the atoms of the host metal, but such diffraction techniques are of small help for small departures from randomness. A technique which does offer promise in the latter instance is the anelasticity of these interstitial alloys. Most previous investigations using this property have utilized alloys in which the solvent is one of the bcc metals, alloys such as These studies have been interpreted to show that an interaction exists between interstitials which causes them to form clusters in more than random numbers; the binding energy of interstitials in such clusters has been deduced to be about 0.1 ev per atom (for small clusters of size two to four atoms). Similar investigations have been carried out on close-packed solvent metals, Ni-C by and Diamond and Ag-O by Papazian.8- In both of these svstems. no relaxation of the singly dissolved interstitial is expected, so an-elastic behavior of the interstitials must be caused by their association in some cluster or complex of non-cubic symmetry. Since relaxations in these alloys were observed to have a strength which varied about as the square of the interstitial concentration, the effect was deduced to be caused predominately by motion of i-i pairs in the crystal. A striking difference is observed in relaxation strength of interstitial alloys between the bcc and fcc systems. The specific effect per interstitial atom is much larger for the alloys in the bcc crystals than for those in fcc crystals. Comparing clusters of size two in the Nb-O system4 and the Ni-C system,7 one finds the magnitude of the anelastic effect per interstitial atom in the former to be some 100 times greater than that in the latter. Such a difference in relaxation strength might be caused by a difference in concentration of the pairs (this means a higher binding energy in the bcc crystals). It might also be caused by a large difference in shape factor of the elastic strain field about the pairs between the two cases (a much more noncubic shape factor would be required for the bcc crystals). This investigation was undertaken to examine the possibility of C-C pair formation in alloys of cobalt and carbon using anelastic effects. Since cobalt has both fcc and hep phases, it seemed to offer the chance that measurements over a range of frequency might permit comparison of properties of pairs in the two crystal types. Although this goal was not reached, several significant facts were deduced from the observations. 1) An anelastic phenomenon believed to be associated with the presence of C-C pairs in cobalt exists. It has many features in common with that observed in nickel. 2) The effect is thought to be caused by pair motion in the fcc phase. 3) Calculations of the relaxation strength A, which includes as a parameter the product of the pair concentration, C, and the square of the shape factor ', show that this parameter is much smaller in the CO-C alloy system than in the interstitial alloys in the bcc systems. 4) From this finding, we reach the conclusion that both the binding energy of C-C pairs in cobalt and the specific relaxation strength per pair are small compared to corresponding values for such pairs in the bcc systems. 5) The crystalline anisotropy of the effect permits the identification of reasonable geometrical models of close C-C pairs. I) EXPERIMENTAL PROCEDURE A) Method of Measurement. The anelastic measurements-—all of which were constant frequency measurements of internal friction—were designed to study the expected phenomenon in both the hcp and fcc structures in cobalt. Knowledge of similar measurements in Ni-C alloys led us to believe that the damping peak should occur below the transformation temperature for frequencies near 1 cps and above for frequencies near 100 kcps. This surmise was correct. The low-frequency measurements were made on wire specimens using a vacuum torsion pendulum; the damping peak was found at about 2'70°C at a frequency of 1 cps. Because of large superimposed damping of magnetic origin at this temperature, a longitudinal magnetic field of about 1500 oe was applied to the

Jan 1, 1969

By J. T. Burwell

As is well known, the alloys of iron containing 18 ± per cent chromium, 8 ± per cent nickel and less than 1.2 per cent carbon exhibit the same allotropic modifications as iron. The face-centered cubic or gamma phase is stable at high temperatures and the body-centered cubic or alpha ferrite is presumably stable at room temperature. The transformation from the gamma phase to the alpha phase in alloys of the above composi-tion (18-8 or stainless steel) is sluggish; even moderately rapid cooling permits the retention of the gamma phase. Cold-work, however, causes the transformation from gamma to alpha to occur at room temperatures. It is difficult, nevertheless, to induce complete transformation regardless of the method of cold-working. Since metallographic polishing is very effective in transforming the surface austenite to ferrite, as indicated by the magnetic studies of Buehl and Wulff, 1 it was decided to investigate the phenomenon by electron diffraction methods.

Jan 1, 1939

THE Searles Lake orebody is located in the north- west corner of San Bernardino County. It is a dry lake bed with an exposed salt surface covering an area of 12 square miles. Recoverable mineral values are contained in the mother liquor below the surface of the lake. Stratification in the lake bed has separated the brine into two bodies which differ in composition. Although liquor is processed from both bodies, this paper will discuss only the upper structure brine. Fig. 1 illustrates a typical cross-section of the two commercial orebodies. The orebody is composed of a porous salt deposit 70 to 90 ft deep. The upper structure is separated from the lower orebody by a 12 to 16-ft thick impervious mud seam, as shown in Fig. 1. These salt structures are composed of 55 pct solid-phase salts and 45 pct voids which are filled with the original mother liquor.

Jan 2, 1954

By Carroll Wegemann

THAT Colorado was producing oil and gas before the fields of the Mid-Continent were discovered is a fact too frequently overlooked. As early as 1862, oil was obtained in the Florence district (see Fig. 1) from seepages and shallow holes. The first well that could be regarded Fig. 1. as being truly commercial was drilled in this field in 1876. The field is now producing 100,000 bbl. per year, and is credited with a total production of approximately 11,000,000 bbl. The small field near Boulder, Boulder County, was opened in 1901; production has now practically ceased but the field is credited" with a total production of 610,000 bbl. Oil was discovered at Rangeley in 1901, and the field supports a small local refinery at the present time. The first shallow well in the White River gas field was drilled in 1892, and the wells now producing have been

Jan 3, 1925

By D. W. Fuerstenau

This paper presents the results of an investigation of the stability of the mass flow rates and average pellet size in the different streams of an industrial-scale balling circuit. The variables in this study include water content, drum speed, and fresh feed rate. It was found that both the mass flow rates and pellet diameter are greatly disturbed when a change, positive or negative, in any of the variables takes place. For most of these disturbances to be damped down, a period of 1 hr or so is required. When a disturbance in the feed rate was made, the transient period extended to more than 1% hr (the duration of the experiment). It was observed that there is an interaction between the drum speed and moisture needed for producing an acceptable green ball product. The moisture content of the product pellets was found to be a function of the pellet size, with the larger pellets retaining a higher moisture content

Jan 1, 1983

PRODUCTION of nonmetallic mineral raw materials used by the fertilizer, ceramic, chemical, and construction industries and many others, was greater during 1953 than in any previous year. Production of fertilizer minerals was the highest in history despite somewhat decreased consumption in the second half of the year. Marketable phosphate rock production increased 10 pct to an estimated total of 13.1 million LT, valued at $78.5 million, and potash production was estimated at 1.8 million tons of K2O equivalent, valued at over $60 million. Crude gypsum output exceeded the 1952 total and approached the record of 8.66 million tons mined in 1951, with indications that 1953 will show a new all-time high. Gains and losses among gypsum products were irregular, with major gains in plate- glass and terra-cotta plasters, sanded building plasters and miscellaneous building plasters, and principal declines in base-coat plasters, prepared finishes and tile. Lath and wallboard outputs were each about 20 pct higher than in 1952.

Jan 2, 1954

By J. E. Dinger, Ross Gunn

Faraday's Law of magnetic induction states that the e.m.f. acting around a closed circuit is equal to the time rate of change of flux through that circuit. If the closed circuit is a conducting medium, there will flow an electric current which is propor¬tional to the conductivity of the material and the time rate of change of the flux. Electrical currents so induced in a con¬ducting material are often referred to as eddy currents. Eddy currents are thus induced into a conducting material by (1) a time rate of change of the magnetic field through the material, by (2) a relative motion of the conducting material and a magnetic field, or by (3) a combination of (1) and (2). Because the magnitude of the induced eddy currents is dependent upon the resistance of the equivalent conducting path, these currents offer a method of detecting electrical discontinuities in a

Jan 1, 1945

By W. T. Hicks

The oxidation of CbO was studied by a gravimetric technique from 400° to 1200°C in oxygen. In this temperature range the oxidatiotz is characterized by an irlductive period of low oxidation rate, which becomes shorter as the temperature increases, followed by a rapid parabolic oxidation. The oxidation of CbO cannot be rate controlling in the oxidation of Cb metal in the temperature range, 800° to 1200°C. A thin optically inactive layer has been observed between the metal and Cb2O5 layer of Cb oxidized at 700°C or higher temperatures. Figs. 1(a) and 1(b) show the edge of a sample of Cb reacted to 50 pct of complete oxidation at 800°C. Fig. l(a) taken under bright field illumination shows a layer of oxide adhering to the unoxidized metal core. Fig l(b) taken under polarized light shows that this oxide layer is

Jan 1, 1962

By D. W. Fuerstenau

Recently R. J. Charles1 showed that comminution of brittle or semi-brittle materials in batch operations is described more appropriately by a variable energy relationship than by the specific relation- ships proposed by Rittinger,2 Kick,3 and Bond.4 That is, the value of n in the empirical differential operation which applies to crushing and grinding (Eq. 1) is variable. Independently, Holmes6 developed an identical generalized equaton for size reduction. The experimental data of Charles and Holmes show that the value of n is determined by the material and the comminuting machine and is constant for a given combination of these two conditions. The general objective of the present article is to extend the Charles-Holmes concepts to continuous ball milling. The specific objective is to analyze the operation of a vibratory ball mill dry-grinding chromite in a continuous open circuit and to develop an equation for the comminution of chromite in this mill.

Jan 12, 1959

By J. L. Huiatt, D. G. Foot

The Bureau of Mines devised a direct flotation method for treating low-grade carnallite (KCl*MgC12*6H20) and sylvinite (a mixture of KC1 and NaCl) ores characterized by a high content of water-insoluble impurities. The procedure consists of flocculation-depression of the insoluble slimes; decomposition leach (carnallite only); potash rougher, cleaner, and recleaner flotation; and final product leaching. The technique eliminates the necessity of removing the water-insoluble slimes by mechanical or flotation desliming. Laboratory results demonstrated that the direct flotation procedure, when compared with conventional techniques, yielded equivalent or improved flotation results with equal or less reagent consumptions. The direct flotation method recovered 81.6% of the solid phase KC1 from camallite ore and 79.7% of the KCl from sylvinite ore in final products containing 60.5 and 60.9% K2O, respectively. A flowsheet incorporating the described flotation procedure is presented.

Jan 1, 1983