Search Documents

ORE at the Jeffrey mine of Canadian John Mansville at Asbestos, Que., is hoisted by two 12 1/2 - ton capacity aluminum skips, counterbalanced. When the loaded skip reaches the surface it empties, via its sliding door, into a bin. Simultaneously, the skip tender, who operates at the 940 level, loads ore into the alternate skip from a 12 ½ -ton measuring pocket. This done, he sets the skips in motion. Problem: When moisture content of the asbestos ore is high, the ore, unknown to the skip tender, some- times sticks in the dumping skip, preventing complete discharge. Moreover, the sliding skip doors sometimes jam and stay open after the ore is discharged. If a skip in this condition is lowered, the result is either an overflow of ore, or the ore discharges through the open skip door, down the shaft. Spilled ore must then be mucked out of the spill pocket and hoisted in 2-ton cars. Cost is high, time is lost, and the shaft is sometimes damaged. Solution: A television apparatus was installed so that the skip tender might quickly spot improper door operation or hang-ups at the dumping station.

Jan 8, 1958

By F. W. Bryan, D. H. Lynch

Introduction This paper is a general description of current central Florida phosphate mining, beneficiation, and product transportation. It is directed and believed to be of interest to engineers not familiar with this industry. Deposit: The phosphate deposits of central Florida are generally located in a five county area which includes Polk, Hillsborough, Hardee, Manatee, and DeSota counties. Geologically, the deposit is of marine origin and is identified as the Bone Valley formation. This formation is Pliocene to Recent in geological age and overlies a Miocene limestone formation known as the Hawthorn. The Bone Valley formation sediments are regionally characterized by equal proportions of apatite, quartz, and clay. The clay is predominantly of the mont-morillonite family. On a local scale, however, the proportions of these three major constituents vary considerably. The phosphate occurs as the apatite mineral (Ca 10F2(PO4)(6) and with the clay and sand, the minable ore is commonly referred to as matrix. This matrix is overlain by unconsolidated overburden of sand and sandy clays, ranging in depth from 10 to 45 ft. The matrix usually occurs in fairly horizontal continuous beds from 3 to 25 ft in thickness. The bedded limestone formation lies directly below the matrix and is generally well defined. The phosphate particles range from 3/4 in. to 200 mesh (Tyler) in size. The phosphate particles coarser than 14 mesh are called pebble phosphate and those less than 14 mesh are termed flotation feed which, when beneficiated, subsequently become concentrates. Through mining and beneficiation, phosphate quality is measured in BPL percent which stands for bone phosphate of lime units. In subsequent chemical manufacturing, the quality is indicated by P205 content. The deposit is economically characterized by various ratios such as tons of product per acre and cubic yards handled per ton of product. Magnesium, iron, and aluminum content are also considered in evaluating ore reserves. These elements are often critical to the chemical fertilizer processes. Presently, an ore body is considered economically minable if it meets the criteria shown in [Table 1]. These, of course, are general guidelines and specific costs and returns on investment must be considered in each case for acquiring reserves. On a new grass-root venture, a 20-30 year life is generally expected with a mineral recovery of 80%. History and Uses Phosphate mining in central Florida began around the turn of the century. However, in the early days, only pebble phosphate was produced until about 1930 when technology was available to beneficiate the -14 + 150 mesh particles. The -150 or -200 mesh material was discarded as it is today. The basic processes for beneficiation are washing, scrubbing, desliming, sizing, and flotation. These basic unit processes are essentially the same today although many improvements have been developed since the early days. Phosphate is used primarily in the production of high analysis fertilizer chemicals, typical of which are triple superphosphate, monoammonium phosphate (MAP), and diammonium phosphate (DAP). Phosphate is also used in the production of food preservatives, dyes for cloths, vitamin and mineral capsules, steel hardeners, gasoline and oil additives, toothpaste, shaving creams and soaps, bone china dishes, plastics, optical glass, photographic films, light filaments, water softeners, insecticides, soft drinks, road fill, and livestock feed supplements. Florida produces over 80% of the nation's marketable phosphate rock and one-third of the world production, according to the US Bureau of Mines. This amounted to approximately 35 million tons in 1975. Exports of Florida phosphate rock were to such countries as Canada, Japan, West Germany, Italy, and India, with Canada and Japan being the major users. Almost 95 o of all outbound cargo shipped through the port of Tampa is phosphate rock or related products. Beneficiation Following is a description of Agrico's new Fort Green beneficiation plant which is typical of the newer large capacity plants being built in the field. Agrico's Fort Green mine was completed in 1975 and is located in the southwest corner of Polk County and is directly adjacent to Manatee, Hillsborough, and Hardee Counties. With some minor differences, Fort Green is typical of a modern central Florida plant. The rated capacity is 3,000,000 plus tons of product per year and this varies according to the richness of the ore being handled. A simplified flowsheet is presented in [Figs.1 and 2]. This plant is served by three draglines of the 40-cu-yd class. The phosphate beneficiation is usually divided into three major functional steps: (1) washing and screening to produce a pebble product and flotation feed, (2) feed preparation and (3) flotation to produce concentrates. The typical plant is similarly divided into these three functional areas. Washer: Briefly, the slurried matrix is pumped from two draglines simultaneously at a combined rate of about 20,000 gpm at 2000 tph (solids) to rotary trommel screens sized to make a 7/8-in. separation. ([See Fig. 1]-) The trommel oversize is sent to hammermills where it is crushed and returned to the trommel screens, or pumped to tailings if minor impurities (Fe203, A1203, MgO) are too high. The trommel undersize is pumped to 14 mesh stationary (static) flat screens. The flat screen over¬size is subjected to three stages of 14 mesh vibrating screening and two stages of log washing in order to produce a final pebble product. The pebble product (+ 14 mesh material) is conveyed by belt conveyor to a large on-ground storage pile. Pebble product is reclaimed through a tunnel and loading system below

Jan 1, 1980

By M. B. Bever, A. K. Jena

THE heats of formation ?H at 273°K of the compound AgMg as a function of composition have been measured by solution calorimetry.1 The value at the stoichiometric composition is -4.41 kcal per g-atom. From electromotive force measurements2'3 the heat of formation at 773°K of stoichiometric AgMg has been determined as -5.19 kcal per g-atom.4 The combination of these two values results in an unusually high negative temperature coefficient of the heat of formation d?H/dT = ?Cp = -1.6 cal per g-atom-OK. By contrast, published heat contents of the compound AgMg and the component elements above room temperature5 indicate that the temperature coefficient of the heat of formation of AgMg is nearly zero. In this communication calorimetrically measured heats of formation of A.K.JENA,Junior- MemberAIME,andM.B. BEVER,Member AIME, are Staff Member, Division of Sponsored Research, and Professor of Metallurgy, respectively, Massachusetts Institute of Technology, Cambridge, Mass. Manuscript submitted July 1, 1968. IMD AgMg below room temperature are reported and the temperature dependence of the heat of formation is discussed. The heat effects of additions of samples of the compound AgMg containing 50.1 at. pct Mg to liquid tin-rich solutions at 623°K were measured in a solution Calorimeter.6 The heat effects of additions plotted against the average of the atom fractions of solutes in the solution before and after each addition were a linear function of composition from which the heat effect at infinite dilution was obtained, Table I. The calorimeter was calibrated by additions of tin; the heat content (H623°K - H273°K) of tin was taken as 4.08 kcal per g-atom.4 The heat effect at infinite dilution of an addition of where heat of formation of AgMg at T°K, T = temperature from which samples are added (78°, 195°. and 273°K), Xi = atom fraction of i in AgMg, ?Hi = relative partial gram-atomic enthalpy of i in tin-rich solution.

Jan 1, 1969

By L. R. Raymond, G. G. Binder

One primary purpose of hydraulic fracturing as a well stimulation technique is to overcome formation damage. The literature provides ways of designing fracture treatments and evaluating their results but not of incorporating formation damage in vertically fractured wells. Results of an investigation of this problem are presented in this paper. Prediction of stimulation ratios in vertically fractured, damaged wells is accomplished with a mathematical model relating stimulation ratio to relative conductivity of fractures whose lengths are not more than about half the drainage radius of the well. Comparison of results from the new model to results in published predictions verify its utility; these results also show that the range of stimulation ratios that can be predicted for undamaged wells is extended to include relative conductivities of less than 300. This extension is important when using fracturing to stimulate wells with high production rates and high native formation permeabilities. For example, large increases in daily oil production rate can be obtained with stimulation ratio increases as low as 1.25. The importance of complete fracture fill-up (uniform proppant packing) is shown through use of the mathematical model. If, at the mouth of a fracture, only a small fraction (1/2 percent) of the total fracture length is not packed with proppant, nearly all the polential stimulation increase is lost. Proppant crushing, compaction and embedment have been shown in laboratory studies to be responsible for low fracture conductivities in wells producing from highly stressed formations. Equipment and methods for testing the effect of stress (overburden) on conductivity of fructures in consolidated and unconsolidated sands are discussed in this paper. Laboratory tests with simlilated fractures in cores from both types of formations showed that crushing, compaction and embedment seriously affect conductivity. Results indicate that similar laboratory tests should be made when accurate knowledge of fracture conductivity is needed to assure good stimulation results for important wells. The chief factor in stimulation ratio reduction was found to be overburden pressure, but the size and type of proppant and the hardness of the formation have significant effects. Fracture conductivity reductions of up to 50 percent were observed with sand propping fractures in consolidated cores; a reduction of 83 percent was measured for an unconsolidated core. The range of effective overburden pressures for which conductivities were measured was from 100 to 5,000 psi. An example fracture design and evaluation problem indicates the usefulness of considering formation damage in planning well stimulation jobs. When damage exists, but its extent and the degree of permeability reduction are not estimated from diagnostic tests, the formation permeability used in planning the job may lead to under-designing. As the example shows, too low a target stimulation ratio can lead to much lower production rates (by half) than could be attained otherwise. Solutions of equations representing several special cases of the mathematical model are presented in graphical form and details of the derivations of the equations are given in the Appendix. INTRODUCTION Since its inception in 1947, hydraulic fracturing has proven to be an effective and widely accepted stimulation technique. In the past 18 years the ability to execute a successful hydraulic fracturing treatment has been substantially increased. The development of design and evaluation procedures1,2 has been one of the major contributions to this increased skill. However, as the art of hydraulic fracturing has moved closer to a science, new problems concerning the design and evaluation of the optimal hydraulic fracturing treatment have arisen. Three questions are pertinent to these problems. I. How is a fracturing job evaluated in a damaged well? 2. What is the effect on the stimulation ratio of not filling the fracture in the vicinity of the wellbore? 3. What is the effect of overburden pressure on fracture conductivity and, consequently, the stimulation ratio? A primary objective of fracturing a well is to stimulate production by overcoming wellbore damage. Presently. however, there is no rational basis for designing or evaluating the optimal fracturing treatment in a damaged well. All present fracture design and evaluation techniques assume that proppants can be uniformly placed in fractures. This assumption may be in serious error, particularly for the portion of a fracture directly adjacent to the wellbore. In this area, turbulence of the injected fluid can cause the proppant to be swept farther into the fracture. Also, loss of fluid from the fracture to the

By T. M. Chance

THE term "low-sulfur coal," as used in this discussion, is limited to coals containing less, or very little more, than 1 per cent. sulfur. For certain purposes it might be advantageous to include coals that contain as much as 1.25 per cent. sulfur, because such coals have been considered as available for making metallurgic coke of fair grade; but the same reasoning might apply to coals containing as much as 1 ½ per cent. sulfur, if facilities exist for utilizing such coal by admixture with coal containing less sulfur. In Pennsylvania, it is not possible to define the exact geographic limits of the areas in which coals relatively low in sulfur exist, because variations in the percentage of sulfur occur irregularly and often abruptly. It is not uncommon to find areas, more or less circumscribed in extent, in which the coal is relatively high in sulfur although all the surrounding territory contains low-sulfur coal; and, similarly, small areas of low sulfur coal exist in districts where the coal is normally high in sulfur. These generalizations apply, With few exceptions, to the whole area underlaid with bituminous coal in the State of Pennsylvania, and also to each of the individual beds of coal in this state. Pennsylvania is poorly supplied with coals of the low-sulfur class. We find, however, as an offset to this condition, very large areas in which coal ranging from 1 to 2 ½ per cent. sulfur exists in beds of good workable thickness. This coal, by washing, can be reduced in sulfur low enough to make coke of a high grade. While a considerable tonnage of workable low-sulfur coal remains in the Pennsylvania bituminous dis-tricts, it has been necessary to turn to the areas of higher-sulfur coal for the supply of metallurgical coke. This utilization of the higher sulfur areas has been made possible either by washing or by selective mining. Washing.-Fine crushing of the entire feed is not generally necessary to the successful washing of Pennsylvania coals. This is due to the fact that the pyrite is rarely finely and uniformly disseminated throughout

Jan 8, 1919

By H. E. Crum, W. E. Hubbard

This review covers the northern 32 counties of the Texas Panhandle, an area 180 miles square. The westerly three-fourths of the district lies wholly within that great area known as the Llano Estacado or "staked plains." Six of the counties produce oil and gas and three produce gas alone. All of the production is associated with the Amarillo arch, a huge anticline superimposed upon a buried mountain range which is undoubtedly a continuation of the Wichitas of southwestern Oklahoma. Oil Production The production of the Texas Panhandle up to Jan. 1,1930, was slightly over 157 million barrels, 90 per cent. of which came from Hutchinson and Gray counties. About 33,000,000 bbl. was produced during 1930. Though this was about 9 per cent. above the 1929 production, it was over 8,000,000 bbl. less than was produced during the peak year, 1928. The present daily production is slightly over 40,000 bbl., which is the allowable production under state-wide proration. The assumed potential for the purpose of proration is 124,500 bbl. and the actual capacity of the wells probably would be in the neighborhood of 100,000 barrels. The total initial production of the oil wells completed in 1930 was 157,289 bbl. from 308 wells, or 511 bbl. per well, as compared to a 734-bbl. average from the 350 oil wells drilled during the preceding year. The completions in Gray County numbered 232, with an average initial of 614 barrels. Completions During 1930, 526 wells were completed in the Panhandle as compared to a total of 503 during 1929. Of the year's completions, 308 were oil wells, 169 produced gas and 49 were dry holes. Of the 3027 wells drilled in the Panhandle to date, 2780 have produced oil, gas or both, making the ratio of dry holes to producers about 1:11.3. Ignoring the 63 dry holes drilled in nonproductive counties, the ratio becomes 184:2780 or 1:15.1 which is slightly less favorable than that which obtained at the end of 1929.

Jan 1, 1931

By S. A. Hoenig

In an earlier publication, the application of exoelectron technology to the monitoring of dry grinding in a ball mill was reported. Recently, the author has investigated the ball mill problem in more detail with the system shown in [Fig.1]. Here, some of the current generated in the ore-ball-water mixture was picked up by the metal chains and served as a measure of the rate of grinding. While the mechanism of current generation has not been completely clarified, a parallel study of electrical effects associated with rock drilling indicated that the major driving force is the zeta potential*, while oxidation of the freshly fractured material provides the remainder of the current. Both of these effects are sensitive to the exposed surface area, and it might be expected that the observed currents would provide a measure of the grinding rate. This "surface area" effect allows the measurement system to be used in any type of rock or ore grinding. Some studies with sulfide copper ore indicate higher currents than those observed with silica sand, but the overall pattern of current versus grinding rate is essentially the same. Experimental Studies The experimental system was set up as shown in [Fig. 1]. The initial studies were done with silica sand because of its availability and for comparison with the data of reference 1. The sand was sized to an average of 425 /MI (40 mesh); a typical charge consisted of 2.5 kg (5.5 lb) of sand, 0.85 L (0.22 gal) of tap water and 2.5 kg (5.5 lb) of iron grinding balls 25.5 mm (1 in.) in diameter. For a typical "run," the mill was loaded with a fresh charge of ore and operated for periods ranging from 10-60 min. During this time, the current was measured with a Keithley 417 picoammeter and a chart recorder. At the end of the grinding period, the charge was removed and sieved to recover the 425, 300, and 212 µm (40, 50, and 70 mesh) fractions which were then drained and weighed. A fresh charge was used for each test and every attempt was made to keep the draining and weighing processes uniform.

Jan 1, 1985

By L. P. Teas

The main facts brought out by the study of the blende-bearing ores examined are as follows: 1. Chalcopyrite as minute triangular or rectangular dots, or as

Jan 1, 1918

Full sets of 149 Vols., including 4 Indexes, covering 1871-1940 incl. Indexes to Vols. 1-35, 36-55, 56-72, 73-117 (set of 4 Indexes)

Jan 1, 1940

By D. S. Flett, D. W. West

The solvent extraction of chromium 111 has been studied for the system Cr 111, H,SO., H,O/RNH/RNH., xylene, where the primary amine used was Primene JMT. Rate studies have shown that extremely long equilibrium times are required, ranging from 1 hr at 80°C to 20 days at room temperature. Heating the solution prior to extraction increases the rate of extraction. The variation in the amount of Cr 111 extracted is an inverse function of the acidity of the aqueous phase. Thus, the slow rates of extraction appear to be connected with the hydrolysis of the Cr I11 species. Extraction isotherms for the extraction of Cr 111 have been obtained for two sets of experimental conditions, namely at 60°C and for a heat-treated solution cooled to room temperature. The separation of Fe 111 from Cr 111 and Cr 111 from Cu 11 in sulfate solution by extraction with Primene JMT has been studied and shown to be feasible. A survey of the literature relating to the solvent extraction of chromium showed that, although many systems exist for extraction of Cr VI, only a very few reagents have been found to extract Cr 111. The extraction of Cr III by di-(2-ethyl hexyl) phosphoric acid has been reported by Kimura.' A straight-line dependence of slope —2 was observed between log D,, and the log mineral acid concentration at constant extractant concentration. Since the slope of this plot reflects the charge on the ion extracted, it must be concluded that a hydrolyzed species of Cr III is being extracted. Carboxylic acids generally do not form extractable complexes with Cr III but di-isopropyl salicylic acie does extract Cr 111. Simple acid backwashing of the organic phase, however, failed to remove the chromium. Similar difficulty in backwashing was found by Hellwege and Schweitzer8 in the extraction of Cr I11 with acetyl-acetone in chloroform. The extraction of Cr 111 from chloride solutions by alkyl amines has been reported4-' but the maximum amount of extraction achieved in these studies did not exceed 10%: From sulfate solutions, however, Ishimori" has shown that appreciable amounts of Cr I11 were extracted by amines. The amines used were tri-iso-octyl amine, Amberlite LA-1 (a secondary amine, Rohm & Haas) and Primene JMT (primary amine, Rohm & Haas). The efficiency of extraction with regard to amine type was primary>secondary> tertiary. Appreciable extraction of Cr I11 was recorded for Primene JMT as the aqueous phase acidity tended to zero. The major difficulty with Cr I11 in solvent extraction systems stems from the nonlabile nature of the ion in complex formation. This accounts for the slow rate of extraction generally experienced and the difficulty encountered in backwashing the Cr I11 from the organic phase in the case of liquid cation exchangers. Consequently, the possibility of extraction of Cr I11 as a complex anion is attractive since the backwashing problems should be minimized in this way. From published data, it appeared that the extraction of chromium from sulfate solutions of low acidity by primary amines afforded the best chance of success for a useful solvent extraction system for Cr iii This paper presents the results of a study of the extraction of Cr I11 from sulfate solution by Primene JMT and examines the application of such an extraction procedure for the recovery of chromium from liquors containing iron and copper. Experimental Chromium solutions were prepared from chrome alum in sulfuric acid and sodium sulfate so as to maintain a constant concentration of sulfate ion of 1.5 molar. Solutions of Primene JMT were prepared in xylene and the amine equilibrated with sulfuric acid/sodium sul-fate solutions, of the same acidity as the chromium solution, until there was no change in acidity between the initial and final aqueous phases. The solutions of Primene JMT conditioned in this way were then used for the equilibration experiments. Equilibrations at 25°C were carried out in stoppered conical flasks shaken in a thermostat; equilibrations at all other temperatures were carried out in stirred flasks in a thermostat. After equilibration, the phases were separated and analyzed for chromium. In the tests on the rate of extraction, small samples of equal volume of both phases were withdrawn from time to time and the chromium distribution determined. The chromium analyses were carried out either coloi-imetrically using diphenyl carbazide, or volu-metrically using addition of excess standard ferrous ammonium sulfate and back titration of the excess iron with potassium dichromate. The oxidation of Cr 111 to Cr VI in the case of the raffinate solution was effected by boiling with potassium persulfate in the presence of silver nitrate and, for the backwash solution, by boiling with sodium hydroxide and hydrogen peroxide. Results Preliminary experiments indicated that extraction results were effected by the age of the chromium solution, higher distribution coefficients being obtained with solutions which had been allowed to stand for some time. Consequently a stock solution of chrome alum, 10 m moles per 1 Cr I11 in 1.4 M Na,SO,/O.l M &SO,,

Jan 1, 1971

By D. B. Dowling

(San Francisco Meeting, September, 1915) THE interest which has been aroused in prospecting for oil in the foot hills of southern Alberta, and in the oil possibilities of the known gas fields situated in the less-disturbed areas, called for a much closer examination of the structure, thickness, and composition of the underlying rocks of the region than had -hitherto been made. The areal geology of the larger part of the great plains was outlined by Dawson, McConnell, and Tyrrell, between 1881 and 1885. The foothill area was not critically examined at that time, owing to the time which would have been required for its proper study and the difficulty that was found in recognizing in the foothills the divisions which had been adopted in the mapping of the formations of the plains. This was clue in great measure to the paucity of exposures in continuous sections of the lower divisions of the Upper Cretaceous. Since the pioneer work on the plains was published, the beds which form continuations south into Montana have been critically examined. The Canadian beds arch over the end of a flat anticline which rises to the south; and two sections in Montana, one on each side of the anticline, help to explain some of the difficulties previously encountered in the mapping of the measures found in the foothills. The index map, Fig. 1, shows the area studied, and its relation to southeastern Alberta, and to Montana.

Jan 6, 1915

By Rufus J. Foster

During the discussion on the Preparation and Utilization of Sniall Sizes of Anthracite (page 613 of present volume), several inquiries were made concerning the use of the McClave grate, which was mentioned by Mr. Coxe as having proved satisfactory in the generation of steam at his collieries, and also at a large number of industrial estal)lishments in Scranton and elsewhere. For a more satisfactory repIy to such inquiries than could be furnished in the oral discussion, I have prepared the following paper to be included in the published proceedings. And, as the use of the fuel under consideration necessarily requires the employment of a blower to change the fire, from a condition giving an incandescent radiant heat only to one giving a hot gaseoua flame as well, I shall add a description of the McClave Argand blower and its method of action. The grate and blower combined form a complete and effective system fcr burning small fuels, such as anthracite culm, birdseye, buckwheat, bituminous slack, etc., in boiler and other furnaces; while the grate alone is now extensively used with the larger sizes of hard and soft coal in furnaces where blast is riot required. Fig. 1 is a view of the RlcClave grate as built in two sections. It is constructed on the principle best approved by practice to prevent warping and burning out; that is, it presents no long lines of

Jan 1, 1892

By R. W. H. Acherson

Blast-furnace flue dust is one of the most troublesome operating factors in the iron and steel industry. It is usually involved in all the unpleasant phases of blast-furnace operations. It adds to our aggravations until we are willing to spend large sums of money to keep it out of our stoves and boilers and more money to handle it again and again on one scheme or another to induce the furnaces to retain it without bad after effects. Several successful operators claim that it is useless to recharge raw flue dust because the furnace would never have blown it out if it had been suitable material for blast-furnace consumption. Most of us who have made persistent efforts to return raw flue dust to the furnaces have decided that it is very often false economy to do so. Yet some remarkable results have been attained at the Ohio Works of the Carnegie Steel Co. through recharging raw dust. The plant comprises six modern blast furnaces. Up to 1909, about 300,000 tons of flue dust had accumulated in stock piles. During the last 10 years, there have been recharged into these furnaces all of the flue dust recovered from the furnace operations, the entire stock pile of Rue dust, and nearly 80,000 tons of dust shipped from other furnaces of the Carnegie Steel Co. The results obtained arc. shown in Table 1.

Jan 1, 1922

By R. W. H. Acherson

Blast-furnace flue dust is one of the most troublesome operating factors in the iron and steel industry. It is usually involved in all the unpleasant phases of blast-furnace operations. It adds to our aggravations until we are willing to spend large sums of money to keep it out of our stoves and boilers and more money to handle it again and again on one scheme or another to induce the furnaces to retain it without bad after effects. Several successful operators claim that it is useless to recharge raw flue dust because the furnace would never have blown it out if it had been suitable material for blast-furnace consumption. Most of us who have made persistent efforts to return raw flue dust to the furnaces have decided that it is very often false economy to do so. Yet some remarkable results have been attained at the Ohio Works of the Carnegie Steel Co. through recharging raw dust. The plant comprises six modern blast furnaces. Up to 1909, about 300,000 tons of flue dust had accumulated in stock piles. During the last 10 years, there have been recharged into these furnaces all of the flue dust recovered from the furnace operations, the entire stock pile of Rue dust, and nearly 80,000 tons of dust shipped from other furnaces of the Carnegie Steel Co. The results obtained arc. shown in Table 1.

Jan 1, 1922

A BLAST can be "full of sound and fury," signifying nothing but a poorly confined charge, or it can be a muffled, well controlled explosion which moves the rock efficiently and places it in the desired location with the least amount of fuss and bother. Why one method will do the job and another proves to be almost useless is shown by the machine-gun camera studies of quarry blasting made by the Atlas Powder Co. staff. The sequence, or machine-gun, camera is the latest scientific device for the study of cause and effect factors in blasting. Movie cameras, previously used, although of some use, were limited because slow shutter speeds and small negatives failed to give clear, sharp prints. During World War II, the AAF developed the sequence camera, which figuratively stops the blast at regular intervals, making study and evaluation feasible. The camera is simple and inexpensive and offers material for accurate examination of blasting techniques. The machine-gun camera takes three 5x5 in. exposures per sec at a 1/450 sec shutter speed, four times faster than a movie camera. Negatives are 30 times larger than those of movie cameras, giving large, sharp prints. The rock movement is frozen on the picture as the sequence of the blast takes place. Pictures on this page show the advantage of individual machine gun photographs. But the sequences made possible by this camera give graphic, dramatic and conclusive support to recently developed detonation theories.

Jan 1, 1952

By Robert J. Willard

The scanning electron microscope (SEM), became commercially available in 1966. Embodying some unique features not provided by conventional electron microscopes, this new electron-optical instrument offers the scientific community a new way of observing the surfaces of materials. In rock mechanics research, the SEM should prove a useful basic tool in characterizing rock fracture on a very small scale and thus contribute to a better understanding of rock behavior at larger scales. This article presents one example of how the SEM is being applied to such research at the Twin Cities Mining Research Center operated by the U.S. Bureau of Mines in Minneapolis. This research center conducts theoretical and experimental studies on a broad range of mechanisms that induce disintegration by the application of energy to rock.1 Some of these studies are concerned with the relation of microstructure to rock behavior and are carried out mainly with the petrographic microscope. At the same time, however, the center recognizes that this relation must be studied through several orders of magnitude, from lattice-size units of rock-forming minerals to field-size rock units. The SEM fits this scheme by extending the capability of the petrographic microscope into smaller orders of magnitude. However, because its resolution is limited to about 200 A at 10,000x, the SEM is not capable of resolving lattice-size units, and hence a conventional electron microscope with a much greater resolution capability is necessary at this order of magnitude.

Jan 6, 1969

By B. D. Cullity

AS methods for measuring fiber textures become more exact, it becomes justifiable to scrutinize an observed pole-density curve for evidence of minor texture components. These are disclosed by minor maxima or abnormally broad major maxima. One possible source of these minor components is twinning of the main component. In cubic metals and alloys, there are two kinds of twins: 1) Annealing twins in face-centered cubic metals. These are reflection twins on {Ill), and they can be expected to be present in recrystallization textures. 2) Deformation twins in body-centered cubic metals. These are shear twins on (112). Although usually formed only by impact, they might conceivably be present in the deformation texture of severely cold-drawn wire. Fortunately, both kinds of twinning lead to the same orientation relationships. It thus becomes possible to prepare a single list of angles between various planes in parent crystal and twin, which is helpful in examining pole-density curves for evidence of twinning in any cubic metal or alloy. Such a list of interplanar angles is given in Table I. This table consists of three parts, corresponding to the three major texture components—<100>, <110>, and <111>-most commonly found in the fiber textures of cubic metals. The table lists the angle between the pole of {hkl}, in either the parent crystal P or the twin T, and the fiber axis <uvu>. The crystals with <uvw> parallel to the wire axis are here

Jan 1, 1959

By J. E. Flinn, E. R. Gilbert

Recently, Green reported some high-temperature, 0.60 to 0.89 T3, creep results on unalloyed tantalum. From his study he determined an activation energy of 114 kcal per mole for steady-state creep using the T, differential-temperature method25 for testing. He accounted for the difference between this value and 110 kcal per mole for self-diffusion by the temperature dependence of the elastic modulus, 4 kcal per mole. This reported activation energy is in apparent disagreement with that which can be determined from Green&apos;s isothermal data, which we have plotted as log creep rate vs 1/T in Fig. 15. From this figure, it appears that there are two activation energies of -185 kcal per mole at the higher temperatures and -75 kcal per mole at the lower temperatures. It is not obvious that the data can be fitted to a straight line corresponding to an activation energy of 114 kcal per mole. One is led to two possible conclusions regarding Green&apos;s study: there are two discrete processes controlling the creep rate from 0.60 to 0.89 Tm or the apparent activation energy is not discrete but continuously increases with increasing temperature. The former speculation would be in closer agreement with the high-temperature creep behavior of tungsten.28 The apparent disagreement between the activation energies determined by the AT and isothermal methods certainly suggests that further study on the high-temperature creep of tantalum is needed.

Jan 1, 1967

By J. D. Miller

The authors have summarized the state-of-the-art in the kaolin clay industry very well. In some instances the problems which they have identified are common to all fine particle separations and in other cases the problems are unique to the kaolin clay industry itself. General areas of research which may be common to other systems and which deserve continued investigation at a higher level of support include: 1) Establishment of the relationship between flotation response and clay structure/composition. 2) Determination of temperature effects in the separation of fine particles. 3) Evaluation of the effect of bubble size on the quality of fine particle separation. The first two areas would require basic surface chemistry studies including microflotation, electrokinetics, adsorption density measurements, and microcalorimetry. The last area would be oriented toward the mechanics of bubble-particle attachment. Regarding the first area, the authors alluded to this research need by commenting on the variation in separation observed from one deposit to another. It seems that a detailed study characterizing the flotation response of various clay types with respect to structure and compositional features would be of considerable value. For example, I understand, that D. W. Fuerstenau&apos;s group has recently been successful in characterization, with respect to structure, of some silicate mineral types--chain, sheet and framework silicates. A similar study should be initiated in which the flotation behavior of various clay minerals kaolinite, halloysite, montmorillonite

Jan 1, 1979

By H. A. Schlesinger

Various studies have estimated that for the next few decades, about half of all new power plants will be nuclear. The other half will be fueled with coal. Pending legislation on air pollution control would require all new coal-fueled power plants to install stack gas scrubbers or other technology to reduce sulfur oxide (SO,) emissions. These regulations would require flue gas desulfurization (FGD) or other technology for SO, reduction even on lower sulfur western coals. Among the options for FGD are single or dual alkali throw away processes using lime or limestone as the major reagent. These processes are currently more economically attractive than recovery processes, such as magnesium oxide and Wellman- Lord, that produce a salable product such as sulfur or sulfuric acid. One of the major problem areas with the throw away processes is disposal of the thrown away solid wastes, primarily calcium sulfite (CaSO3) and calcium sulfate (CaS04). Coal ash also must be disposed of, even if SOx reduction is not required. This paper addresses the alternatives for handling and disposal of throw away lime, limestone, and dual alkali process solid wastes. Advantages, disadvantages, and the economics of various methods are discussed. Both large central station power plants (500-1000 MW capacity) and smaller industrial power plants (up to 100 MW capacity) are considered. High sulfur eastern coals (53% S) and lower sulfur (3 1% S) western coals are considered.

Jan 1, 1981