Search Documents

By R. Stratton-Crawley

Flotation-related processes utilizing an oil phase for processing fine mineral particles have been described and various applications discussed. The problems associated with the techniques are varied, but may be summarized by the following areas; (1) applicability to fine particle beneficiation, e.g. collector extender and emulsion flotation. (2) major 'mechanical' problems, e.g. emulsion breakage and oil recovery in oil flotation. (3) complex interfacial chemistry, e.g. empirical nature of pigment flushing .

Jan 1, 1979

By Chester A. Rowland

INTRODUCTION Comminution is generally a feed preparation step for subsequent processing stages; exceptions being when a final product such as aggregates, specification sand, Portland Cement, and similar products is produced. Grinding, the fine product phase of comminution, requires a large capital investment and frequently is the area of maximum usage of power and wear resistant materials. Grinding is most frequently done in rotating drums utilizing loose grinding media, lifted by the rotation of the drum, to break the ores in various combinations of impact, attrition and abrasion to produce the specified product. Grinding media can be the ore itself (autogenous grinding -- primary and secondary), natural or manufactured non-metallic media (pebble milling) or manufactured metallic media -- steel rods, steel or iron balls. This chapter will discuss general mill design and the specific design and application of the following types of tumbling grinding mills. [Overflow Rod Mills Figure 1 Peripheral Discharge Rod Mills Figures 2 and 3 Compartment Mills Rod and Ball Figure 6 Ball Figure 6a Pebble Mill Figure 6b Overflow Ball Mills Figure 8 Diaphragm (Grate Discharge) Ball Mills Figure 9] I. GENERAL MILL DESIGN A. Liners The interior surface of grinding mills exposed to grinding media and/or the material being ground are protected from wear and corrosion by rubber, metallic, a combination of rubber and metallic, or non-metallic wear resistant materials. B. Drives Economics at the time of plant design and mill purchase determine the drive to be used. The simplest drive is the low speed synchronous motor with speeds in the range of 150 to 250 RPM connected to the mill pinion-shaft by either an air clutch or flexible coupling.

Jan 1, 1982

By W. C. Ellis

NONFERROUS alloys upon which desirable properties can be conferred by heat treatment are becoming of increasing industrial importance. The alloys of copper with a constituent which has a solubility varying with temperature are materials of this character. Some of the constituents which are effective in producing a change in the mechanical properties of these alloys upon heat treatment are, according to Corson,1 nickel and silicon, iron and silicon, cobalt and silicon, and chromium and silicon. In addition to these elements, Gregg2 states that the combination of beryllium and silicon is effective in producing age-hardening characteristics in copper. The effect of these elements, however, as dispersion-hardening constituents in the copper alpha solid solutions does not seem to have been studied in any considerable detail. This paper deals with the heat treatment and properties of three alpha brasses containing 3 per cent. of nickel plus silicon in the proportion necessary to form the compound nickel silicide, Ni2Si. Some information of a preliminary nature in regard to the hardening by heat treatment of phosphor bronze containing the same percentages of nickel and silicon is included. The method of hardening the alloys, which is effective in increasing the tensile strength and proportional limit, is similar to that used in, the case of duralumin type aluminum alloys. It consists of a quench from a temperature at which the hardening constituent is in solid solution, followed by an aging at a lower temperature to precipitate the dissolved constituent in a dispersed condition. This results in an increased resistance of the alloy to deformation with an attendant improvement in the tensile properties.

Jan 1, 1929

By G. T. Jackson

PROPERTY AND LOCATION THE Alaska Gastineau Mining Co.'s mine is located at Perseverance, about 4 mi. east of Juneau, Alaska. Its property consists of a group of claims, the lode system traversing these claims for a distance of 11,000 ft. (3352 in.). It is shown in Fig. 1. FIG. 1.-ALASKA GASTINEAU MINING CO.'S PROPERTY NEAR JUNEAU. The ore deposits occur in what is known as the Juneau gold belt. This gold belt can be traced for about 50 mi. northwest of Juneau and 40 mi. southeast. It consists of a single band, several hundred feet wide, in which stringers and veins of quartz, carrying gold, occur in a slate formation near its contact with some altered volcanic rock known as greenstone.

Jan 9, 1919

By Edwin S. Smith

Current research in the phenomenon of liquefaction has indicated some of the in situ material properties which should be considered in the planning of waste deposits. Practical experience in tailings disposal, however, must be combined with the results of theoretical and laboratory studies to develop the most economical and safe techniques against liquefaction failure. One of the many responsibilities of mining engineers and mill superintendents is providing for the safe and economic disposal of wastes (or tailings) that remain after a mineral has been extracted from an ore. The cost of disposal of these tailings exerts a considerable influence on the minimum grade of ore extracted from the mine. It varies to a great extent with each project and is dependent on many diverse factors, such as the local topographical, meteorological and seismological conditions together with the applicable water pollution laws of the area. The process used to extract a mineral from an ore determines the physical characteristics of the tailings and, thus, is one of the more important factors to be considered in the planning of disposal facilities. Today's trends in ore-processing operations complicate the problems of waste disposal: recently developed extraction methods result in the production of finer tailings, the use of lower grade ores produces greater volumes of wastes, and the enhanced land values in the vicinity of industrial plants preclude the former practice of spreading wastes laterally and force the expansion of waste deposits upwards to greater heights. The frequent occurrence of stability problems in waste deposits indicates that many mining organizations may not be employing current soil mechanics concepts and practices. One of the most spectacular, and often most disastrous, types of tailings dike failure is that resulting from liquefaction of the fine particles combined with a breach of the main retaining dike. TAILINGS DISPOSAL Since the many variations in site conditions, ore bodies and extraction processes dictate the general disposal procedures and mill superintendents incorporate special facilities to provide the most economical disposal method consistent with accepted safety standards, it is only natural that there are almost as many different disposal techniques as there are disposal areas. Methods used in the construction of retaining dikes include: (1) transporting granular material from an adjacent borrow pit and (2) mechanically segregating the total effluent and allowing the coarse fraction to form a retaining dike by hydraulic deposition. The location of a plant and the surrounding topography exert the greatest influence on the layout of tailings disposal facilities. Most of the above-ground waste deposits can be classified as side-hill, (Fig. 1,) cross-valley, (Fig. 2,) or stockpile deposits. Side-hill disposal areas are probably the most common type of layout because of the natural advantage of gravity flow, without the disadvantage of river diversion usually needed for tailings ponds formed behind cross-valley dikes. Stockpiles, which are placed on relatively level ground, require four retaining dikes and the effluent generally has to be pumped up into the disposal area. Changing production techniques or developments adjacent to disposal areas have produced variations or partial combinations of these three categories. In a series of articles, Lenhart describes many of the problems encountered in the disposal of tailings and certain innovations used to overcome them. He discusses weaknesses in design and layout and shows that disposal techniques are often learned the

Jan 1, 1970

By F. G. Miller, T. D. Mueller, L. B. Davidson

A mathematical model of reservoir behavior during one cycle of the intermittent steam injection process is presented in this paper. A cycle of the process is considered to be composed of three stages: injection, condensation and production. The model concentrates on behavior during the production stage. The influence of several parameters on production improvement is described, using the results obtained with a numerical equivalent of the model. Reservoir system parameters considered are thickness, reservoir thermal conductivity, oil viscosity, solution gas-oil ratio and the change in oil effective permeability with temperature. Operating parameters investigated are heat injection rate, steam temperature and cumulative injection time. In the face of considerable uncertainty, the model appears to give a fair prediction of the behavior observed during an actual test. This makes the model a useful means of selecting projects. It is shown that the model may also be utilized to select an optimum set of operating conditions for a particular project. Results of this study show the extent to which production improvement depends on each of the parameters investigated and give an indication of the range of system conditions within which the process would be effective. INTRODUCTION In recent years the intermittent steam injection or steam soak process of oil recovery has become a popular method of improving recovery in reservoirs bearing high-viscosity hydrocarbons. Production improvement due to the process results from heating the reservoir near the wellbore. The process is applied on an individual well basis and is executed in a series of cycles, each consisting of three stages: injection, condensation (the soaking period) and production. During the injection stage, high-pressure steam is injected into the reservoir surrounding the well-bore. This study assumes that injection is carried out over the entire vertical section of the reservoir rock that can be exposed to fluid injection. The condition of steam entering the reservoir is considered to fall within the following limits: (1) steam pressures less than 1,000 psig, (2) steam temperatures between 300 and 700F and (3) steam quality less than 90 percent. The last restriction is due to equipment limitations. Normally, injection re maintained for less than 3 weeks. After termination of injection, the condensation stage begins. The well is shut in for several days, supposedly to make certain that the injected steam condenses. This condensation would insure the retention of injected heat. The production stage is initiated when the well is opened again. Reservoir response during this stage determines the effectiveness of the process (response is defined as the oil production rates, the water production rates and the wellbore temperatures observed during the entire production stage). The immediate response of the reservoir is sometimes quite good. Sets of case histories by Longl and by Owens and Suter2 give some typical figures for response. Duration of the production stage is equal to the time needed for the oil production rate to decline to some predetermined value. This usually requires 4 to 6 months. Termination of the production stage coincides with the start of the next cycle. The process is continued, cycle by cycle, until it becomes unprofitable to continue. One simple model2 and two more sophisticated models3,4 of the process have been presented. These are based on fundamentally different assumptions than those used in this investigation. Although the three models might be modified to fit the assumptions used in this study, it is felt that greater rigor would result by developing a

By Henry A. Stiff, J. P. Hammond, A. B. Westerman, H. C. 195-000-000-014 Cross, and Lawrence E. Davis

The phases in Cr-Fe-Mo alloys have been investigated with homo-genization, aging temperature, composition range, and alloy addition as variables. Metallography, three X-ray methods, and hardness were used as methods of study. The behavior of s, M23,C8, and Z phase are reported for cornpasition range 60 pct Cr-15 to 25 pct Fe-15 to 25 pct Mo-<0.005 to 0.36 pct C with aging at 1400º to 2000°F. With 2 pct Ti, Tic and TiC-TiC are formed; with nitrogen Cr2N. THE recently developed class of chromium-base heat-resistant alloys shows appreciably higher strength than commercially used high temperature alloys. However, further developmental work is required to impart needed shock resistance and some degree of room-temperature ductility to these alloys. Extensive exploratory work on chromium-base alloys was begun in a program initiated by the War Metallurgy Committee of the National Defense Research Council at the Climax Molybdenum Co. in the early part of 1942.&apos; Alloys were sought for gas-turbine blades for use at 1600°F. A minimum of 5 pct elongation in the stress-rupture test was a requirement. From the Climax work, ternary alloys of chromium, iron, and molybdenum appeared to show the greatest promise as materials for gas-turbine blades. The composition line in the ternary diagram joining the 60 pct Cr-15 pct Fe-25 pct Mo and 60 pct Cr-25 pct Fe-15 pct Mo alloys was indicated as representing the most useful combination of strength and ductility.&apos; Strength increased while ductility decreased as molybdenum was raised in this composition range.&apos; The 60 pct Cr-15 pct Fe-25 pct Mo type alloy was thought to have the most suitable properties for gas-turbine blades.&apos; Concurrent with the study reported here, other investigations were being made on Cr-Fe-Mo alloys. The liquidus temperatures on a series of low carbon, ternary alloys were being determined, and isothermal sections drawn at 2370°, 2010°, and 1650°F (1300°, 1100°, and 900°C).2 Also, various methods of preparation and some mechanical and physical properties of chromium-base alloys, particularly the 60 pct Cr-15 pct Fe-25 pct Mo type, were being investigated., At the inception of the present program, only a limited study had been made of etchants for developing the microstructures of chromium-base alloys; X-ray analysis of the microconstituents had not been made. A review of the literature revealed that no phase-diagram work had been reported on the Cr-Fe-Mo system. Scope of Work The work on chromium-base alloys includes the following: 1—The development of etching methods for differentiating between the microconstituents; 2—The identification of microconstituents by X-ray diffraction methods; and 3—A comprehensive metallographic and hardness study after various heat treatments. The phases were studied by three standard X-ray techniques: 1—The block-sample focusing-camera method; 2—The powder-diffraction method on elec-trolytically separated residues; and 3—The powder-diffraction method on cold-worked aggregate samples. The results by the first two methods were correlated with the metallographic data. The third method was used largely to study conditions approaching equilibrium, since cold working prior to heat treating accelerated precipitation. Seven types of alloys were investigated: 50 pct Cr-50 pct Fe, 40 pct Cr-40 pct Fe-20 pct Mo, 55 pct

Jan 1, 1953

R,. P. JaRvis,* El Oro, Estado de México, México.—The practical problem raised by Mr. Wisser—that is, the determination of the lower limit of ore deposition, below which it is useless to look for ore shoots—is one of the most important in economic geology. He asks: "Can we learn to determine the position of such a line?" For individual districts, yes; but its determination has always been by empirical methods; that is by actually exploring the veins to such depths that the values drop below the economic limits. Usually the signs are plain enough that values have been bottomed without confirmation by the chemist or assayer. Most veins, when approaching their limit, begin to split into branches or stringers; the vein matter itself undergoes a change from "lively looking" rock to one that is dull and unpromising, the quartz, instead of having segregated into clean vein matter, has simply spread itself into the country rock, rendering this more siliceous but no richer—these, together with inclusions of the country rock in the vein, are all positive indications of the limit. Mr. Wisser seems disposed not to accept the law of cause and effect, which he calls "empiricism." He says: "Empiricism embodies an assumption perhaps not evident at first glance. It is this: that like effects spring from like causes and therefore necessarily have a common meaning." There can be no doubt as to the validity of this law, since it is the foundation stone upon which are built all inductive sciences, including economic geology. When demonstrable, proved facts become confused with inferences, as they seem to be generally in the paper under examination, no sound conclusions can be reached. Mr. Wisser has failed to give sufficient data covering the two vein systems which he cites as examples. Presumably they are situated in the Pachuca District of Mexico, but not everybody is familiar with the vein systems there in spite of the fact that it is world famous as a silver producer. Are these two systems separated some distance horizontally from one another and how far? He has given no estimate of the amount and kind of rock that has been eroded from over the present veins. His description of the two systems appears on page 100, beginning: "1. East-west veins," and ends on page 101, "they would lack spaces there in which to deposit." On page 101, with the paragraph beginning "On the other hand," he gives a picture of what he believes takes place in class 2 veins. The sum of this seems to be, according to Mr. Wisser&apos;s observations, that, in the east-west veins, class 1, there has been an invasion of an "altering solution," which I judge has been responsible for the formation of extensive "alteration haloes"; that these alteration solutions have followed along pre-existing fractures or fissures; and that after these alteration solutions finished their work the mineralizing solutions deposited the vein matter and metallic values. Mr. Wisser does not specify clearly what the "alteration haloes" consist of; in other words, what change the original rock has suffered, whether oxidizing, carbonating, or sulphidizing. If they came from depth they could not be oxidizing or carbonating, and in this case it is a bit

Jan 1, 1941

R,. P. JaRvis,* El Oro, Estado de México, México.—The practical problem raised by Mr. Wisser—that is, the determination of the lower limit of ore deposition, below which it is useless to look for ore shoots—is one of the most important in economic geology. He asks: "Can we learn to determine the position of such a line?" For individual districts, yes; but its determination has always been by empirical methods; that is by actually exploring the veins to such depths that the values drop below the economic limits. Usually the signs are plain enough that values have been bottomed without confirmation by the chemist or assayer. Most veins, when approaching their limit, begin to split into branches or stringers; the vein matter itself undergoes a change from "lively looking" rock to one that is dull and unpromising, the quartz, instead of having segregated into clean vein matter, has simply spread itself into the country rock, rendering this more siliceous but no richer—these, together with inclusions of the country rock in the vein, are all positive indications of the limit. Mr. Wisser seems disposed not to accept the law of cause and effect, which he calls "empiricism." He says: "Empiricism embodies an assumption perhaps not evident at first glance. It is this: that like effects spring from like causes and therefore necessarily have a common meaning." There can be no doubt as to the validity of this law, since it is the foundation stone upon which are built all inductive sciences, including economic geology. When demonstrable, proved facts become confused with inferences, as they seem to be generally in the paper under examination, no sound conclusions can be reached. Mr. Wisser has failed to give sufficient data covering the two vein systems which he cites as examples. Presumably they are situated in the Pachuca District of Mexico, but not everybody is familiar with the vein systems there in spite of the fact that it is world famous as a silver producer. Are these two systems separated some distance horizontally from one another and how far? He has given no estimate of the amount and kind of rock that has been eroded from over the present veins. His description of the two systems appears on page 100, beginning: "1. East-west veins," and ends on page 101, "they would lack spaces there in which to deposit." On page 101, with the paragraph beginning "On the other hand," he gives a picture of what he believes takes place in class 2 veins. The sum of this seems to be, according to Mr. Wisser&apos;s observations, that, in the east-west veins, class 1, there has been an invasion of an "altering solution," which I judge has been responsible for the formation of extensive "alteration haloes"; that these alteration solutions have followed along pre-existing fractures or fissures; and that after these alteration solutions finished their work the mineralizing solutions deposited the vein matter and metallic values. Mr. Wisser does not specify clearly what the "alteration haloes" consist of; in other words, what change the original rock has suffered, whether oxidizing, carbonating, or sulphidizing. If they came from depth they could not be oxidizing or carbonating, and in this case it is a bit

Jan 1, 1941

By C. E. Lesher

THE Disco* process for the production of low temperature coke and its immediate predecessor, the Wisner or Carbocite process have been described in the voluminous literature of low temperature carbonization.1 This paper will describe the development of the process from the first attempt at commercial operation by the American Gas and Electric Co. at Philo, Ohio, Yn the 1920&apos;s to the successful operation in 1949 by the Disco Co., a division of the Pittsburgh Consolidation Coal Co., of the 1000-ton per day Disco plant near Pittsburgh, see Figs. 1-2. In the 1924 coal industry depression following the hectic post World War I expansion, the northern Appalachian, unionized bituminous coal fields were affected first and foremost, and Western Pennsylvania as hard as any. Competitive market pressure was heaviest on the lower grades of steam coals, notably the from the Panhandle district where ash and sulphur are inherently higher than in the same Pittsburgh coal bed to the east along the rivers. The firm structure of Panhandle coal while favoring the prepared sizes, depressed the usefulness and value of the finer sizes. Panhandle slack and nut slack were marketed with difficulty at consistent, and at times considerable, loss. Many solutions were suggested, and the Pittsburgh Coal Co. investigated all. Lower delivered prices through lower mine costs and more advantageous freight rates were obvious goals, but equally obvious were the difficulties of self attainment of either in any substantial measure. Selling Btu&apos;s in pipes was abandoned as an idea after a thorough study of the economics of distribution of what was then, and is even now, the only developed continuous process of complete gasification of bituminous coal-producer gas. Although the coal company purchased huge blocks of electric power, it sold not a car of coal to the central power stations. Public utilities controlled the markets for electric current, and it was found that no matter at how low a cost current might be put on the bus bars by the coal company, distribution to its widely scattered coal mines made such an enterprise practically impossible. Consolidation of underground operations and a huge modernization program of mining operations in the 1920&apos;s were but preparation for the introduction of mechanical cleaning of the coal for market, particularly the smaller sizes of steam, gas, and by-

Jan 1, 1953

By C. E. Lesher

THE Disco* process for the production of low temperature coke and its immediate predecessor, the Wisner or Carbocite process have been described in the voluminous literature of low temperature carbonization.1 This paper will describe the development of the process from the first attempt at commercial operation by the American Gas and Electric Co. at Philo, Ohio, Yn the 1920&apos;s to the successful operation in 1949 by the Disco Co., a division of the Pittsburgh Consolidation Coal Co., of the 1000-ton per day Disco plant near Pittsburgh, see Figs. 1-2. In the 1924 coal industry depression following the hectic post World War I expansion, the northern Appalachian, unionized bituminous coal fields were affected first and foremost, and Western Pennsylvania as hard as any. Competitive market pressure was heaviest on the lower grades of steam coals, notably the from the Panhandle district where ash and sulphur are inherently higher than in the same Pittsburgh coal bed to the east along the rivers. The firm structure of Panhandle coal while favoring the prepared sizes, depressed the usefulness and value of the finer sizes. Panhandle slack and nut slack were marketed with difficulty at consistent, and at times considerable, loss. Many solutions were suggested, and the Pittsburgh Coal Co. investigated all. Lower delivered prices through lower mine costs and more advantageous freight rates were obvious goals, but equally obvious were the difficulties of self attainment of either in any substantial measure. Selling Btu&apos;s in pipes was abandoned as an idea after a thorough study of the economics of distribution of what was then, and is even now, the only developed continuous process of complete gasification of bituminous coal-producer gas. Although the coal company purchased huge blocks of electric power, it sold not a car of coal to the central power stations. Public utilities controlled the markets for electric current, and it was found that no matter at how low a cost current might be put on the bus bars by the coal company, distribution to its widely scattered coal mines made such an enterprise practically impossible. Consolidation of underground operations and a huge modernization program of mining operations in the 1920&apos;s were but preparation for the introduction of mechanical cleaning of the coal for market, particularly the smaller sizes of steam, gas, and by-

Jan 1, 1953

By S. A. Falconer

Much attention and publicity has been given, during recent years, to grinding, classification, flotation, and thickening. The various technical papers, and symposiums held to discuss these important phases of milling, have contributed to a better understanding of the fundamental principles and operating variables involved. Another important part of milling— to the flotation operator—is a treatment step to which frequently too little attention is given—"conditioning," or the treatment the ground mineral pulp receives before it enters the flotation machines. "Conditioning" is a hackneyed and frequently misused term, commonly employed to describe the pretreatment of surfaces of minerals in ore pulps or mill products prior to froth flotation. In general, such pretreatment is for the purpose of changing the flotation characteristics of these mineral sur- faces to enable them to respond in some desired predetermined manner when subjected to flotation. Taggartl states that the function of conditioning is "either to insure selective collector coating of one mineral species while another species is not; or to take such steps as will compensate for departure therefrom." As 0. C. Ralston has stated? ... we are still faced with the fact that some mineral particles are water-avid, others air-avid, and that by properly modifying them they may be enhanced or diminished in desirable or undesirable avidity. Coatings on minerals must still be assumed to fall into three classes: (1) a coating of immiscible oil, (2) a layer of adsorbed substance, (3) a chemically produced coating. It is submitted that the process of preparing mineral surfaces for subsequent flotation treatment should take into consideration physical as well as chemical means for altering the normal flotation response of the mineral surfaces. A more descriptive word than "conditioning" is needed to designate broadly these procedures. The minerals in many ores cannot be made to respond in a normal manner to usual methods of "conditioning" with selectivity modifying reagents, until they have been cleansed, or interfering slimes and soluble salts have been removed from the ore. Therefore, it appears important to include under the general subject of "conditioning" a discussion of the purposes, methods used, and some of the advantages of these pretreatment steps. This is dealt with under the subject heading " Initial Treatment of Mineral Surfaces and Ore Pulps." Under this broader interpretation, the methods employed for treating mineral surfaces to alter their flotation characteristics may be divided into three general classes: 1. Physical methods.

Jan 1, 1950

By J. Spotts McDowell

Preparation and Use.-Magnesite is an important refractory in open-hearth, heating, and electric furnaces for steel-making and in many of those employed in the metallurgy of copper and lead. It is sold in the form of brick, finely ground "furnace magnesite" for brick-laying, and dead-burned grains for making and repairing furnace bottoms. The latter are a mixture of granules varying in size from pieces of about 5/8 in. (1.6 cm.) diameter to very fine but sandy particles. Dead-burned magnesite results from calcining &apos;the crude or lightly burned mineral at a temperature that will not merely drive off practically all the CO2, but will also cause sintering of the particles. During this process the pieces shrink considerably and become hard, dense, and inert to atmospheric moisture and C02; under-burned material, on the other hand, will hydrate on exposure to the air. A small percentage of ferric oxide seems to be necessary for the production of a satisfactory sinter; from 4.5 to 8 per cent. in the dead-burned grains is considered the most desirable amount. Dolomite has been little used for brick-making in the United States, but it is prepared for use in the granular condition calcined or "double-burned" and is the principal ingredient of several materials offered for sale under various trade names for refractory purposes. Dolomitic refractories are almost wholly confined to the open-hearth and electric furnaces, where they are used for fettling and as substitutes for magnesite. Much more magnesite and dolomite are used for basic open-hearth steel-making than for all other refractory purposes. The hearth of the furnace is usually built up of magnesite brick and dead-burned grain magnesite so laid that the brick base is protected by a working bottom of the granular material. The latter is sintered into place in layers 1 to 2 in. (2.5 to 5 cm.) thick to a total depth of 12 to 18 in. (30 to 45 cm.) at the center of the furnace. After each heat, burned dolomite is thrown against the banks as high as it will stick, and all holes in the bottom are filled. At most plants such holes, at the end of each week, are also

Jan 2, 1919

By A. M. Kivari

OPERATIONS at the cement plant of the Permanente Corporation, in the hills about 45 miles south of San Francisco and 12 miles west of San Jose, are interesting to the members because of the adoption of modern hydrometallurgical methods for handling and beneficiating raw materials. Closed-circuit grinding, classification, hydro-separation, flotation, agitation, and thickening are familiar terms at this cement plant. These methods make it possible to process refractory limestone into suitable materials for the manufacture of modern cements. Construction of the plant, having originally a design capacity of 7000 bbl. of cement per day, was started in June 1939, and the first clinker was ground on the following Christmas Day. At present the capacity is about 12,000 bbl. of finished cement per 24 hr., most of the production being low-heat cement.† About 3130 tons of limestone, 620 tons 0f clay and 100 tons of gypsum are required daily for this output. Occasionally iron oxide is added to the clay to obtain the desired composition. This, together with the gypsum, is purchased from outside sources. Up to the present time, the corporation has produced low-heat, normal, moderate heat, moderate-sulphate-resisting, high-early-strength, oil-well, modified-oil-well, and plastic cements. Most of the present production is for Shasta Dam, near Redding, Calif., the total demand being 5,800,000 bbl, of cement. Following are some of the cement requirements of the Shasta Dam specifications: [PERCENT Chemical composition: Loss in ignition2.25 Insoluble residue0.75 SO32.25 MgO5.00 Uncombined lime in clinker (CaO)1 .25 Percentage of iron oxide to alumina ratio1.5 Compound composition: Tricalcium silicate (3CaO.Si02)Not more than 3,5 Dicalcium silicate (2CaO.Si02)Not less than 40 and not more than 65 Tricalcium aluminate (3CaO.Al2O7)Not more than 7 Tetracalcium aluminoferrite (4CaO.A12O3.Fe203) Not more than 0 Fineness:] The average specific surface in the bin sampled shall be not less than 1800 sq. cm. per gram and no individual sample less than 1600 sq. centimeters. Compressive strength: The average compressive strength-in pounds per square inch of three mortar cubes composed of one part cement and 2.75 parts fine testing sand, by weight, shall be equal to or greater than the following:

Jan 1, 1941

By G. P. Walters, W. C. Fuller

THE production of thin films of beryllium became essential early in the irradiation program at Harwell in order to study the fundamentals of irradiation damage in this metal. In common with other metals, electron-microacope specimens of beryllium can be produced by different techniques. The techniques used to produce thin-film specimens varied according to the starting material. Most of the starting material was -0.060 in. thick. Large-area specimens (1 in. long by 0.5 in. wide) were chemically thinned to -0.005 in. thick in a solution containing 85 pct orthophosphoric acid, 10 pct chromium trioxide, and 5 pct sulfuric acid at 70°C prior to electropolishing. Small-area specimens, Fig. 1, had to be mechanically thinned prior to electropolishing because chemical thinning considerably reduces the area as well as the thickness. Mechanical thinning tends to produce a worked layer about 0.002 in. deep and hence this method cannot be used to thin bulk specimens below about 0.005 in. thick. Mechanical thinning is carried out by mounting the specimen on perspex then carefully polishing on wet grinding papers. Polishing is continued until about half the initial thickness is removed; the reverse side is then polished in a similar manner. After the bulk specimens have been mechanically or chemically thinned to -0.005 in. they are elec-tropolished in the solution shown in able I at 50" to 80°C. This solution should be prepared by adding the chromium trioxide to the orthophosphoric acid and then the glycerol last. The glycerol should be added slowly because a vigorous effervescence can occur. Electropolishing is carried out by holding the specimen in stainless-steel tweezers and gently agitating in the solution. Masking or "window" techniques are not required for beryllium, good microscope specimens being obtained from the edges of elec-tropolished foils. A stainless-steel beaker should be used, acting as the cathode and solution container. A closed circuit voltage of 30 v is used for polishing. Too low a voltage produces a matt surface and pitting occurs when it is too high. The solution temperature is important. If it is too low, the solution is viscous and bad polishing results and, if too high, etching of the specimen occurs. After electropolishing, the foils are thoroughly

Jan 1, 1963

By C. E. Lesher

THE Disco* process for the production of low temperature coke and its immediate predecessor, the Wisner or Carbocite process have been described in the voluminous literature of low temperature carbonization.1-4 This paper will describe the development of the process from the first attempt at commercial operation by the American Gas and Electric Co. at Philo, Ohio,&apos; in the 1920&apos;s to the successful operation in 1949 by the Disco Co., a division of the Pittsburgh Consolidation Coal Co., of the 1000-ton per day Disco plant near Pittsburgh, see Figs. 1-2. In the 1924 coal industry depression following the hectic post World War I expansion, the northern Appalachian, unionized bituminous coal fields were affected first and foremost, and Western Pennsylvania as hard as any. Competitive market pressure was heaviest on the lower grades of steam coals, notably those from the Panhandle district where ash and sulphur are inherently higher than in the same Pittsburgh coal bed to the east along the rivers. The firm structure of Panhandle coal while favoring the prepared sizes, depressed the usefulness and value of the finer sizes. Panhandle slack and nut slack were marketed with difficulty at consistent, and at times considerable, loss. Many solutions were suggested, and the Pittsburgh Coal Co. investigated all. Lower delivered prices through lower mine costs and more advantageous freight rates were obvious goals, but equally obvious were the difficulties of self attainment of either in any substantial measure. Selling Btu&apos;s in pipes was abandoned as an idea after a thorough study of the economics of distribution of what was then, and is even now, the only developed continuous process of complete gasification of bituminous coal-producer gas. Although the coal company purchased huge blocks of electric power, it sold not a car of coal to the central power stations. Public utilities controlled the markets for electric current, and it was found that no matter at how low a cost current might be put on the bus bars by the coal company, distribution to its widely scattered coal mines made such an enterprise practically impossible. Consolidation of underground operations and a huge modernization program of mining operations in the 1920&apos;s were but preparation for the introduction of mechanical cleaning of the coal for market, particularly the smaller sizes of steam, gas, and by-

Jan 1, 1952

By Foster Bain

MOST of us householders in the East burn anthra-cite, so the problem that interests us most is the distribution and supply of the domestic sizes of anthracite. That, however, is only a small part of the coal problem and has its own peculiarities. Whether anthracite prices are high or low is largely a matter of relativity, depending on the size of the transaction, the available supply, and other things. As an isolated example which I hesitate to quote because it is not entirely representative, you may be interested to know that the Government fuel yard has been delivering to the Government buildings in the District of Columbia, white-ash stove coal at 16 c. a ton less during January, 1923, than during the same month of 1922. The reason is that the Government deals only with large companies who have been wise enough not to boost their prices and the small increase at the mine has been more than offset by the decrease in railroad rates. The total cost is $12.50 per ton, but I want to make it perfectly clear that it does not follow that this would be a just price for a retail dealer to charge the domestic consumer. For example, in the Government business there is no such thing as a bad debt, and certain other fixed or general charges are charged to other departments. The Bureau of Effi-ciency made an effort to determine what would be a. legitimate handling charge for a retail dealer, in Washington, and concluded that if the Government&apos;s cost of handling was $1.00, then $1.88 would be the corresponding fair charge to pay a retail dealer carrying the same volume of business, allowing for bad debts, complete depletion and depreciation of his equipment, and 10- per cent. profit. Assuming that this is the correct differential for Washington, it does not&apos; follow that it would be equally just for Pittsburgh, New York, or elsewhere; nor does it by any means follow that it is a fair differential this year, because the dealer, after being unable to use his equipment in the summer months, now has to deliver an unusually large quantity of coal. I merely cite this instance to show that on the basis of primary cost of coal plus railway charges the retail price is not necessarily higher this-year than last.

Jan 4, 1923

By Alexander Knoll, Dwight L. Baker

THIS paper is a report on work undertaken to investigate the results and conclusions of Ravitz and Porter1,2 that galena freed of surface oxidation products and lead carbonate ("clean" galena) is waterrepellent, and that the action of xanthates in flotation is the action of a cleansing agent, enabling oxidized galena particles to expose a pure lead sulphide, water-repellent surface. The apparatus, in construction and use, was essentially that of Ravitz and Porter. The only significant modification introduced by the present authors was the substitution of a three-necked flask for the flotation cell as the "reaction vessel." Our procedure was to place 50 grams of freshly ground, minus 200-mesh galena in the reaction vessel, sweep out all molecular oxygen from the system with oxygen-free nitrogen, and proceed to wash the galena surface free of its oxidation products with repeated small portions of (I) ammonium acetate (500 c.c. of water, 200 grams of ammonium acetate) or (2) ammonium chloride, hydrochloric acid (2 liters containing 200 grams of ammonium chloride and 25 c.c. Of 1.18 sp. gr hydrochloric acid). The galena was next washed with many 100-c.c. portions of oxygen-free, distilled water. The galena was finally considered free of soluble salts when wash water that had been in contact with the mineral for at least 48 hr.* gave negative tests for: (x) lead ion with sulphide; (2) chloride with silver ion; (3) acetate with cuprous chloride, sodium chloride; and (4) ammonium ion with Nessler&apos;s reagent. Next 500 c.c. of potassium ethyl xanthate solution, free of dissolved oxygen, was run onto the "clean" galena particles. For this system there were determined: I. The wetting properties of the clean galena particles by shaking the reaction flask and noting the degree of mineral collection at the liquid-air interface. This was, of course, simply a qualitative test, but it proved adequate for our purpose. 2. The removal of xanthate ion from the potassium xanthate solution on being shaken with the "cleansed" mineral. Xanthate concentrations were determined by iodine titration according to the methods of Taylor and Knoll.3 3. The pH of the xanthate solution after having been shaken with the "cleansed" galena. The pH was determined colorimetrically.4 The results of five experiments of the type mentioned above are given in Table x.

Jan 1, 1941

By Alexander Knoll, Dwight L. Baker

THIS paper is a report on work undertaken to investigate the results and conclusions of Ravitz and Porter1,2. that galena freed of surface oxidation products and lead carbonate ("clean" galena) is water-repellent, and that the action of xanthates in flotation is the action of a cleansing agent, enabling oxidized galena particles to expose a pure lead sulphide, water-repellent surface. The apparatus, in construction and use, was essentially that of Ravitz and Porter. The only significant modification introduced by the present authors was the substitution of a three-necked flask for the flotation cell as the "reaction vessel." Our procedure was to place 50 grams of freshly ground, minus 200-mesh galena in the reaction vessel, sweep out all molecular oxygen from the system with oxygen-free nitrogen, and proceed to wash the galena surface free of its oxidation products with repeated small portions of (I) ammonium acetate (500 c.c. of water, 200 grams of ammonium acetate) or (2) ammonium chloride, hydrochloric acid (2 liters containing 200 grams of ammonium chloride and 25 c.c. of 1.18 sp. gr. hydro chloric acid). The galena was next washed with many 100-c.c. portions of oxygen-free, distilled water. The galena was finally considered free of soluble salts when wash water that had been in contact with the mineral for at least 48 hr.* gave negative tests for: (I) lead ion with sulphide; (2) chloride with silver ion; (3) acetate with cuprous chloride, sodium chloride; and (4) ammonium ion with Nessler&apos;s reagent. Next 500 c.c. of potassium ethyl xanthate solution, free of dissolved oxygen, was run onto the "clean" galena particles. For this system there were determined: I. The wetting properties of the clean galena particles by shaking the reaction flask and noting the degree of mineral collection at the liquid-air interface. This was, of course, simply a qualitative test, but it proved adequate for our purpose. 2. The removal of xanthate ion from the potassium xanthate solution on being shaken with the "cleansed" mineral. Xanthate concentrations were determined by iodine titration according to the methods of Taylor and Knoll.3 3. The pH of the xanthate solution after having been shaken with the "cleansed" galena. The pH was determined colorimetrically.4 The results of five experiments of the type mentioned above are given in Table I.

Jan 1, 1941

By Louis A. Riley

I DESIRE to submit, for the consideration and information of the members of the Institute, the following data, drawings, and tables, showing what I believe will be interesting information with regard to the diamond drill, and its uses in developing mineral lands. I would first say that the results given have been obtained during the past two years by means of two drilling machines belonging to the Lehigh Valley Coal Company, operating on their coal lands in the Mahanoy, Lehigh, and Wyoming regions. 1st. A tabulated statement, giving location of borings, date, progress, total cost, itemized cost per foot, etc. 2d. Section showing strata bored in Nos. 5 and 10 holes at Mt. Carmel, see Plate VI. 3d. Section showing strata bored in No. 19 hole at Hazleton, see Plate VI. 4th. Photograph and description of drill No. 2. From the first it will be seen that the total number of test-holes bored up to May 1st of this year is 24; 9 of these are in the Mahanoy region, 6 in the Lehigh region, and 10 in the Wyoming region, in all of which cores have been taken for the whole distance. The total distance bored is 9902 feet. The majority of the holes have been put down for the purpose of proving the lower veins of the coal series, and have had to encounter the harder rocks of the coal formation. Much of the distance has been through the lower conglomerates, going in some cases through the coarse egg conglomerate, the foundation of the coal deposit, and to the green sandstone and red shale which underlie it. These lower sandrocks and conglomer¬ates are among the hardest known to geologists, and present a formidable resistance to the exploring drill. This fact must be taken into consideration in comparisons of cost of drilling, and when considered will still further improve the very favorable results I am able to show in my statement of costs. In illustration, I will cite the work of one bit when boring in the upper or softer rocks of the Wyoming region, where 280 feet were obtained without resetting, while in the Lehigh and Mahanoy regions, in the lower and harder rocks, bits set with the same quality of diamonds would only bore from 3 to 20 feet before being worn out. In this connection it may

Jan 1, 1877