Search Documents

THE increased demand for titanium alloys with improved high-temperature creep strengths has stimulated interest in silicon as an alloying addition to titanium. Silicon is a potent solid-solution strength-ener and, if added in sufficient concentration and properly heat-treated, can also dispersion-strengthen titanium by eutectoid decomposition.' However, better understanding of the nature and distribution of the resulting silicide dispersion in more highly alloyed titanium matrices is necessary for the development of useful titanium alloys which utilize the latter strengthening mechanism. This note describes the chemical and crystallographic characteristics of the silicide phase as it occurs in a typical high-temperature near-a titanium alloy matrix. Several Ti-6A1-3Sn-3Zr a11oys containing various amounts of silicon ranging from 0.1 to 1.0 pct were melted as 10- to 20-lb ingots and processed into 1/2-in.-diam bar stock. The microstructures of specimens annealed at various temperatures were conveniently summarized by the (Ti-6Al-3Sn-3Zr)-Si pseudobinary phase diagram illustrated in Fig. 1. Comparison with the Ti-Si equilibrium diagram indicates the substitutional solutes (Al-Sn-Zr) increase the eutectoid temperature and decrease the a terminal solubility. Annealing at temperatures sufficiently high to dissolve the silicon in a ß solid solution and cooling rapidly enough to preclude coarsening generally produced a uniform dispersion of fine silicide particles, whereas annealing at temperatures near but below the ß transus produced relatively coarse silicide particles. Annealing in the limited a, plus 3 region produced a duplex coarse and fine silicide array. Several a-annealed specimens were examined by X-ray diffraction to determine the crystallographic identity of the precipitate phase. Copper Ka X-ray diffraction patterns of bulk specimens which contained 0.5 and 0.8 pct Si were virtually identical to that of the silicon-free Ti-6Al-3Sn-3Zr base alloy except for a slight shift in some of the high-angle diffraction lines. Apparently the silicide volume fraction was too low to be detected in bulk specimens. X-

Jan 1, 1969

By R. P. Laforce, ZJ. R. Low, A. M. Turkalo, D. F. Stein

The interaction of the crlloying eletnenls, nickel and chromium, with the impurity elements, antimony, pIzosphorus, tin, and arsenic, to producse reversible temper brittleness in a series of high-purity steels containing 0.40 wt pct C has been investigated. The alloyed steels contained approximately 3.5 pcl Ni, 1.7 pct Cr, and 0.05 to 0.08 pct of the particular irnpurity to be investigated. Susceptibility to teirlper embrittlement was measured by comparing the notched-bar transition temperature of each steel after quenching from the final temper and after very slow cooling (step cooling;) following the final temper. A plain carbon steel without alloying elements, bu/ ud/h 0.08 pel Sh, does not embrittle when step-cooled through the emzbrittling range of temperatures. The same embrittling treatment, applied to a steel with about the same antinzony content but with nickel and chvonziunz added, causes a 700°C increase in transition temperature. If chromium or nickel is the only alloying element, the increase in transition temperature is only 50%, again with antimony present. A carbon-free iron containing nickel, chromium, and antimony shou~s a 200°C shift in transition temperature for the same thermal treatment. Specific alloy-impurily interactions are also observed for the other impurity elements, phosphorus, tin, and arsenic. Additional investigations involving electron microscopy, trzicrohard-ness tests of vain boundaries, minor additions of zirconiutn and the rare earth and noble metals, nzainly with negative results, are also described. HE particular type of embrittlement investigated is that which is encountered in alloy steels tempered in the temperature range from about 350" to 525'C or slowly cooled through this range of temperatures when tempered above this range. This type of embrittlement is sometimes called reversible temper brittleness to distinguish it from the embrittlement indicated by a minimum in the room-temperature V -notch Charpy energy vs tempering-temperature curve encountered in the range 28 0" to 350°C. Temper brittle-ness seriously restricts the use of many alloy steels since it precludes tempering or use in the embrittling range of temperatures and may significantly raise the ductile-brittle transition temperature of heavy-section forgings and castings tempered above the embrittling range, since such sections cannot be sufficiently rapidly cooled after tempering to avoid embrittlement. The very voluminous literature of temper brittle-ness up to about 1960 has been reviewed by woodfine' and LOW.' Of particular significance to the present investigation was the demonstration by Balajiva, Cook, and worn3 that high-purity Ni-Cr steel does not exhibit temper brittleness and the subsequent detailed and systematic study by Steven and Balajiva~ of the effect of impurity additions on the susceptibility to embrittlement of Ni-Cr steels. Steven and Balajiva showed that, of the impurities which may be found in commercial steels, Sb, As, P, Sn, Mn, and Si could all produce temper brittleness in a high-purity Ni-Cr steel. The principal purpose of the present investigation was to study the effects of particular alloy-impurity combinations on susceptibility to temper embrittlement. The steels used were high-purity 0.30 to 0.40 wt pct C steels containing 3.5 wt pct Ni and 1.7 wt pct Cr, separately or in combination. The susceptibility of these steels was then determined when approximately 500 ppm by weight of antimony, arsenic, phosphorus, or tin were added as an impurity. The melting, casting, and forging practices used in the preparation of the materials investigated are described in Appendix A. Table A-I in this appendix shows the analysis of all steels to be discussed. The steels were produced as 20- or 2-lb heats. The smaller heats were used after it had been demonstrated (see Appendix B) that a small, round, notched test specimen could be used to measure the shift in the ductile-brittle transition temperature caused by temper brittleness with about the same result as that obtained by Charpy testing. HEAT TREATMENT Unless otherwise noted, all steels were tested for embrittlement in the tempered martensitic condition. A typical heat treatment for a 0.40 C, 3.5 Ni, 1.7 Cr steel was: 1 hr at 870"C, in argon, quench into oil at 100"C, quench into liquid nitrogen, temper 1 hr at 625"C, and water-quench. The warm oil quench was used where quench-cracking was encountered; otherwise the initial quench was into room-temperature oil or water. For other compositions austenitizing temperatures were 50°C above Acs with the remainder of the thermal cycle the same. Steels in this condition, with no further heat treatment, are designated as non-embrittled. The above quenching and tempering cycle for the 0.40 pct C steels resulted in as-quenched hardnesses of 48 to 53 RC and as-tempered hardnesses of 24 to 31 Rc except in the case of the plain nickel or plain carbon steels. In these, the as-tempered hardness was as low as 80 to 90 Rg. No attempt was made to adjust the tempering temperature to obtain the same hardness in ali steels since it was felt that a uniform thermal cycle was more important than exactly equivalent hardness values. Pro- the standard quench and temper described above, the standard embrittling treatment was "step-cooling". For this the thermal cycle was: 593"C, 1 hr; furnace-cool to 538"C, hold 15 hr; cool to 524"C, hold 24 hr; cool to 496"C, hold 48 hr; cool to 468'C, hold 72

Jan 1, 1969

By S. S. Shen, M. J. Pool, P. J. Spencer

Heats of solution of gold and copper in dilute Au-Cu-Sn alloys have been determined using a liquid metal solution calorimeter. The self-interaction coefficient, Au - has been calculated at constant copper concentrations and n cu has likewise been determined at constant gold contents. Good experimental agreement is obtained between the interaction coefficients and nAu Cc thus demonsbating the reliability of the measured heat values. The measured data are compared with the Predictions of certain solution models. In previous publications,1,2 the results of calori-metric investigations of dilute Ag-Au-Sn and Ag-Cu-Sn alloys have been presented. The present work on the Au-Cu-Sn system concludes a program of studies of enthalpy interaction coefficients in dilute alloys of the Group IB metals with tin. Since the definition and derivation of an enthalpy interaction coefficient has been discussed previously,1,2 no restatement of this theory will be presented here. From the determination of the partial heat of solution of gold and copper in ternary alloys of various copper and gold contents, values of the interaction coefficients can be calculated. These coefficients give an insight into the various solute interactions that occur in the liquid solutions since changes in their magnitude and sign reflect bonding changes that are taking place in alloys of varying solute contents. EXPERIMENTAL Details of the design and operation of the liquid metal solution calorimeter used in this work may be found in a paper by Poo1.3 For the present studies copper of 99.999 pct purity was supplied by American Smelting and Refining Co., gold of 99.999 pct purity by A. D. Mackay, Inc., and tin of 99.99 pct purity by Baker Chemical Co. At the commencement of each series of experimental drops, a tin solvent bath consisting of between 70 and 90 g of the pure metal was inserted in the calorimeter. The weight of the bath was accurately determined and to it were added appropriate amounts of gold or copper to give alloys of the desired composition. For determinations of approximately 0.0015 g-atom samples of Cu were used and for measurements of ?HAu approximately 0.0025 g-atom additions of Au. The heat capacity of the bath was determined at regular intervals during a series of drops using tin calibration samples. Measurements were made of the heat of solution of copper in alloys containing a constant 0.01, 0.02, 0.03, and 0.04 mole fraction of Au, respectively, in order to determine ?HCu in each alloy, and the same mole fractions of copper were used to determine equivalent values for nAu at constant copper concentrations. The composition of the bath was maintained at the desired constant gold or copper content by making calculated additions of the appropriate solute throughout the experiments. The limiting values ?HAu in alloys of constant copper content and of %c, in alloys of constant gold content were studied as a function of the mole fraction of copper or gold respectively in order to determine and nCu. Heat content and heat capacity data used in calculating values of ?ºHAu and ?HCu at the experimental temperature of 720°K were obtained from Hultgren et a1.4 ' RESULTS AND DISCUSSION Determinations of ?HAu. The partial heat of solution of gold in pure tin as a function of gold concentration was determined in the previous study of dilute Ag-Au-Sn alloys1 and can be represented by the least-squares expression: ?HAu(l) =-8075 + 2413xAu [l] which is valid between XAu= 0.00 and xAu = 0.05. The standard error in the constant term, which represents the partial heat of solution of gold at infinite dilution in tin,?HºAu(l)is 35 cal per g-atom, while the standard deviation of the slope, which represents n Au is ± 619 cal per- agtom. Corresponding expressions for ?HAu(l) in alloys containing constant mole fractions of 0.01, 0.02, 0.03, and 0.04 copper were obtained from the data listed in Table I and are themselves given in Table II. Fig. 1 illustrates the partial heat of solution of gold as a function of its concentration in each of the alloys. For the four alloys of constant copper concentration, the values obtained for ?HºAU(l) (in order of increasing copper content) are -8141 i 36 cal per g-atom, -8210 ± 42 cal per g-atom, -8202 ± 46 cal per g-atom and -8268 ± 51 cal per g-atom. The corresponding values of the self-interaction coefficient, n Au, for these alloys are 3103 * 644 cal per g-atom, 2425 ± 676 cal per g-atom, 2574 * 717 cal per g-atom and 2523 ± 899 cal per g-atom. In Fig. 2 these values of n Au are plotted as a function of the copper content of the alloys and are seen to remain approximately constant within the experimental limits. The addition of increasing, small amounts of copper to dilute binary Au-Sn alloys thus has no apparent effect on Au-Au interactions in these dilute liquid solutions, although more exothermic values of ?HºAu(l) do result from an increase in the copper content of the alloys. Analogous behavior was observed with additions of silver to dilute Au-Sn alloys.' By

Jan 1, 1970

By W. F. Hosford, E. W. Kelley

Deformation studies have been conducted at room temperature on single crystals of magnesium and magnesium alloys with thorium and with lithium. Single crystals oriented to suppress shear on the easily activated basal slip systems were deformed by plane-strain compression. Compression along the C axis was accommodated by {1011} banding. Compression perpendicular to the unconstrained c axis activated {1012} twinning, and, after virtually complete twinning, deformation continued by {1011) banding in the twinned material. Compression perpendicular to the constrained c axis was accommodated by the simultaneous operation of (1012) twinning against the constraint and (1011 ) banding. Although this orientation was favorable for {1010)(1210) prism and {1011}(1~10) pyramidal slip, these modes were not observed in pure magnesium or in Mg-0.5 pct Th. However, {10i0)(1~10) prism slip was observed in crystals of Mg-4 pct Li during compression perpendicular to the constrained c axis. Fracture in all materials occurred parallel to (1124) or {l~il) depending on the orientation and composition of the specimen. THE mechanical behavior of the hcp metals is strongly anisotropic. Although several slip systems have been reported the slip is cpmmonly in the directions of closest packing, the (1210),' and this does not produce strains parallel to the c axis. Hence the inherent anisotropy. The deformation mode most easily activated in magnesium at room temperature is (0001)(1210)- basal slip. Also {1010}(1~10) prism slip and {1011)(1210) pyramidal slip have been reported, primarily at elevated temperatures.2"4 However, at room temperature the shear stresses to activate the prism and pyramidal modes are roughly a hundredfold greater than that required for basal slip.'j4 Thus prism and pyramidal slip may be expected only under special conditions of loading. Strains normal to the basal plane can be produced by twinning, however. Many twinning modes have been reported for magnesium,' with (1012) twinning the most common and relatively easy to activate. Magnesium can deform by (1012) twinning when stressed along the c axis jn tension, but not in compression. In contrast, (1011) twinning is activated by compression along the c axis and not by tension. In addition to primary twinning, secondary twinning or slip can occur within the reoriented material of primary twins.' In general at least five independent shear systems must be active to bring about an arbitrary shape change such as that in the individual grains of a deforming polycrystalline material.' Because basal slip can_ provide only two independent shear systems and (1012) twinning can only accommodate an extension of the c axis, other deformation modes must be active in magnesium for an arbitrary shape change to occur. The purpose of this investigation has therefore been to study the various deformation modes in magnesium at room temperature, with special emphasis on those modes that are less easily activated. The effect of the alloying elements, thorium and lithium, has also been investigated. In polycrystalline aggregates, unambiguous identification of deformation modes is extremely difficult and the direct evaluation of the resolved shear stresses to activate them is not feasible. On the other hand, uni-axial tension and compression experiments on single crystals may not activate some of the- deformation modes because basal slip and/or {1012) twinning cannot be suppressed in most orientations. However, it should be possible to activate all possible deformation modes using oriented single crystals and plane-strain compression. Identification of active deformation systems and evaluation of the resolved shear stresses required to activate them should be facilitated. Wonsiewicz and Backofen have recently completed an investigation of the plasticity of pure magnesium crystals at various temperatures utilizing plane-strain compression and selected crystal orientations. This technique has also been used in the present work. The seven orientations selected for study are indicated in Table I. Plane-strain compression along the c axis (orientations A and B) should activate some deformation mode _other than basal, prism, or pyramidal slip, or (1012) twinning. In orientations C and D, prism or pyramidal slip would be expected to take place. When the compressive load is applied perpendicular to an unconstrained c axis (orientations E and F) the three slip modes should be suppressed but not (10i2) twinning. In orientation G, basal slip should occur.

Jan 1, 1969

By Jack Washburn, E. R. Parker

Kinking in zinc single-crystal tension specimens was observed under conditions of low stress and high temperature. Kinking is discussed in relation to other plastic bending phenomena on the basis of dislocation theory. Experiments on the stress-induced motion of small angle boundaries are reported. KINKING was first reported by Orowan1 as a new deformation mechanism. He observed the phenomenon in cadmium single crystals loaded in compression. Glide lamellae in a local region of the rod were observed to snap over suddenly to a tilted position, resulting in a sudden shortening of the specimen. Between the tilted portion and the rest of the crystal there were fairly sharp boundaries, with the slip plane assuming approximately mirror image positions on opposite sides of these boundaries. Orowan considered the boundaries to be regions where dislocations had concentrated. Hess and Barrett' observed the formation of kinks in critically oriented zinc compression specimens. It was found that the sudden snapping over of the tilted region was not an essential part of the kinking phenomenon but rather was associated with the method of loading. Kinking was explained on the basis of the accepted mechanisms of slip and flexural glide. It was also suggested that a kink can be considered as a special type of deformation band. During a recent investigation of the effect of surface condition on creep of zinc single crystals," a similar phenomenon was observed in crystals which were loaded in tension. The specimens were 0.4 in. diam cylindrical rods with a free length of 4 in. between end connections. All of the crystals were tested at a constant load. adjusted to give an extension rate of approximately 0.05 pct per hr. Kinking, as shown in Fig. 1, occurred in some of the tests performed at temperatures above 200°C. Kinking was observed in specimens varying widely in initial orientation, scattering about a 45" angle between the slip plane and the specimen axis. The condition leading to kinking in tension appeared to be non-uniform distribution of flow along the gage length combined with the restraint imposed by the tensile load. At low temperatures and fast strain rates, the distribution of strain throughout the midsection of tension specimens was generally quite uniform; therefore, bend planes developed only near the ends as described by Miller.4 However, at high temperatures under creep conditions it was difficult to obtain specimens in which the distribution of flow was uniform. Some of the factors which may have caused differences in flow stress along the length of the crystals are: Nonuniform distribution of impurities, accidents of growth (lineage structure), slight bending or other damage during handling, surface conditions, and strain-aging characteristics due to dissolved nitrogen." Plastic flow, once started in a local region, often continued to a relatively large strain before other parts of the gage length became active. Under these conditions a series of kinks, such as those in Fig. 1, were produced. Fig. 2 illustrates how a nonuniform distribution of slip produces bending moments which- are responsible for kink formation. If no plastic bending were to occur while the rod extended by pure slip in two separate sections of the rod, it would assume a shape such as that in Fig. 2a. A specimen having this shape and being subjected to a tension load would have concentrations of stress at the concave surfaces C and lower than average stress would exist at the convex surfaces D. Therefore a bending moment is superimposed on the average stress in the regions between C and D. The positions of potential bend planes under these conditions are shown as dotted lines. Actually no such shape as Fig. 2a develops because plastic bending in the region C-D occurs simultaneously with pure slip in the intervening regions. The observed structure of a tension kink is indicated by Fig. 2b. Perhaps the best approach to an understanding of kinking as well as other related plastic bending phenomena, such as the bend planes discussed by Miller,' cell formation studied by Wood et al.,6 and polygonization,7 is consideration of the dislocation model of a bent lattice. Current theories of the slip process postulate generation or multiplication of dislocations at certain lattice imperfections. The mechanism proposed by Frank and Read8 results in continuous generation of concentric dislocation loops which spread out

Jan 1, 1953

By R. F. Stewart, A. W. Hall

A method has been developed for continuously measuring the moisture content of coal. The method is based on the thermalization of fast neutrons by hydrogen in the coal. Neutrons from a small radio-isotope source penetrate the coal, are scattered by hydrogen, and measured by a thermal neutron detector. The number of thermal neutrons counted can be directly correlated with the moisture content of coal. In a pilot-scale system, moisture was measured continuously within 0.2% in coal moving at rates up to 20 tph. The method is adaptable in industry for continuously measuring the moisture content of coal at high tonnage flow rates. Such an application would permit continuous recording of moisture in coal without sampling and facilitate quality control. An automatic and continuous method of measuring the moisture content of coal is needed by the coal industry. Automatic control of the coal quality would reduce the cost of coal preparation, improve the product, and thus indirectly increase the use of coal. Moisture in coal can be determined by several methods, but the time required to obtain samples and analyze them by existing methods makes it difficult, if not impossible, to control the quality of the product. Both producers and consumers need a method for continuous and instantaneous measurement of moisture content without sampling in order to regulate process equipment and keep the moisture content of coal within specifications. At the Morgantown, W. Va., Coal Research Center we are developing a nuclear method for continuous measurement of moisture in coal. This method is based on the thermalization of fast neutrons by hydrogen in the water and organic matter of coal. Neutrons from a small radioisotope source penetrate the coal, are scattered by hydrogen, and are measured by a thermal neutron detector. The number of thermal neutrons counted can be directly correlated with the moisture content of coal. Design of a moisture meter based on neutron thermalization depends on many variables, any or all of which can affect the sensitivity of the meter. These factors include those related to the nuclear aspect; type and size of neutron flux and source, type of detecting device, and background count; and those related to the coal being tested: rank, particle size, and ash content. A survey was initiated to eliminate the relatively insignificant factors and to ascertain the magnitude of the major effects. Such information was necessary to fully evaluate the technique and to establish design criteria. Coal contains a relatively large amount of hydrogen in the organic coal substance and the water of hy-dration of the shaly material as well as in the moisture. To apply this concept of moisture measurement to coal requires that the organic substance in coal from any one seam of a particular mine be uniform in hydrogen content. The difference in total hydrogen content of wet and dry coal is relatively small, so that a moisture measurement based on this concept requires a measurement between two large numbers to a high degree of precision. Thus, it was necessary to develop a highly precise instrumentation system for continuous measurement and to obtain a physical arrangement permitting measurement of moving coal with a minimum effect from density variation. EXPERIMENT WITH TRAYS OF COAL Tests were conducted with metal trays containing SO to 100 lbs of coal to develop an instrument system of high precision. A scaling system with a maximum instrument error of 0.2% was used to test different types of thermal neutron detectors. The most suitable type of detector was a boron-10-lined proportional counter tube. While this type of detector showed satisfactory stability, extensive testing disclosed a long-term count reduction probably due to some type of deterioration in the detector. However, development of an electronic system using dual detectors eliminated this deterioration as a serious problem. (The second detector would be used to measure a reference drum of dry coal — the difference in count rate between the wet coal and dry reference coal being a direct measure of moisture content.) Table I, column 1, shows typical results with a 1-curie plutonium-beryllium neutron source and a thermal neutron detector beneath a tray of coal and illustrates the precision of measurement. Consecutive measurements (indicated in Table 1, columns 2-5) of thermal neutrons at various times and positions be-

Jan 1, 1968

By T. P. Floridis, J. H. Young

The need for close control of the phosphorus content of steels has led to numerous investigations on the equilibria of the dephosphorization reactions. Winkler and chipman1 have established the general conditions for effective dephosphorization of steel. They are high slag basicity, high oxygen potential, and low temperature. Other investigators have made additional contributions to the understanding of the dephosphorization process. The current status of the understanding of the dephosphorization of steel is concisely presented by Bodsworth2 and by Ward. The investigation reported in this communication was undertaken with the purpose of establishing the effect of additions of barium oxide and calcium fluoride on the dephosphorizing capacity of slags. Esin and Gel'd4 proposed that barium oxide, being more basic than calcium oxide, should cause an increase in dephosphorizing capacity when added to steelmaking slags, or when used as a substitute for calcium oxide. Derge5 has also proposed that in the future conventional slags might be replaced by BaO-Al2O3 slags. There is, however, no experimental evidence confirming the effect of barium oxide on the dephosphorizing capacity of slags. The effect of calcium fluoride on the dephosphorization of steel is not clearly understood. It is generally recognized that additions of calcium fluoride are beneficial. It is not clear, however, whether calcium fluoride affects the equilibrium of the dephosphorization reaction, or whether it simply causes an increase in the fluidity of the slag and, consequently, faster approach to equilibrium. The experimental procedure consisted in equilibrating synthetic molten slags with liquid copper at 1550°C under a gas stream containing argon, hydrogen, and water vapor. In all experiments the argon to hydrogen ratio was approximately 4:1, and the hydrogen to water ratio was 5.42:l. Molybdenum crucibles were used as containers for the slag and metal. Under the above-described conditions of temperature and composition of atmosphere, there was no observable attack of the crucibles by the metal, slag, or atmosphere. Copper was used instead of iron, because iron attacks molybdenum. The equilibration was made in a tubular furnace consisting of a recrystallized alumina tube. The alumina tube was heated by electrical resistance. A Pt-40 pct Rh wire winding was used for most runs. A silicon carbide tubular resistor was also used for some runs. Temperatures were measured with a Pt-Pt-Rh (10 pct Rh) thermocouple and kept constant within ±5°C. Equilibrium was approached from both sides, i.e., by adding the phosphorus either as oxide in the slag or as a phosphorus-rich alloy of phosphorus and copper. The holding time at the equilibrium temperature was 6 hr. At the end of each run the crucibles were rapidly cooled and removed from the furnace. The slag and metal were separated and analyzed. The experimental results are shown in Table I. The phosphorus content of the slag is expressed both as percent phosphorus pentoxide and as percent phosphorus. The basicity ratio is computed by dividing the number of moles of basic oxides-oxides of barium, calcium, magnesium, and sodium—by the number of moles of acidic oxides- oxides of aluminum, phosphorus, and silicon. Calcium fluoride is not included in the computation of the basicity ratio; i.e., calcium fluoride is assumed to be neither basic nor acidic. The distribution ratio of phosphorus—percentage of phosphorus in the slag divided by the percentage of phosphorus in the metal- is plotted in Fig. 1 against the basicity ratio. The results indicate that slags containing barium oxide have greater dephosphorizing capacity than slags containing calcium oxide. The high dephosphorizing capacity of slags containing sodium oxide and the low dephosphorizing capacity of magnesia-containing slags which already have been reported in the literature2 are confirmed by the results of this investigation. It appears that calcium fluoride has a beneficial effect on the distribution of phosphorus between slag and metal in acid slags only. Although the obtained distribution ratios between the phosphorus contents of slag and copper are not directly applicable to the dephosphorization of steel, they are sufficient for evaluating the effect of slag additions on the dephosphorizing capacity of slags in general. An increase in the ratio of distribution of phosphorus between slag and metal indicates lowering

Jan 1, 1968

By Frank Julian

The determination of manganese by precipitation with potassium chlorate from a solution in concentrated nitric acid, filtration through asbestos, and solution in a reducing agent whose excess is estimated, is open to the objections that the filtration and subsequent solution of the binoxide are apt to be very slow, and that the asbestos may (according to Troilius), unless perfectly purified, affect the titration. In the following modification, filtration is avoided. I give the method as I use it for Bessemer steel. In an 8-ounce Griffen beaker dissolve 1 gramme drillings in 15 c.c. nitric acid (1.2 sp. gr.). Evaporate to 5 c.c.; add 20 c.c. concentrated nitric acid and precipitate with chlorate as usual, avoiding a large excess; then add about 60 c.c. warm water, and 10 c.c. of the oxalic solution; stir until of a clear light yellow color, and titrate with permanganate while the solution is at about 80' C. The binoxide should dissolve immediately when the oxalate isadded. The titration is rapid, and the end-reaction, though transient, easily caught after a little practice. The standard solutions used are: 15 grammes crystallized ammonium oxalate to a liter, and 1.6 grarnmes potassium permanganate to a liter. For standardizing the permanganate, to 10 c.c. of the oxalic solution is added 50 c.c. of hot water, and a solution of 1 gratnme of steel in concentrated nitric acid, from which the manganese has been removed by potassium chlorate and filtration through asbestos. I have made a large number of determinations in steel, pig-iron,

Jan 1, 1888

By H. Papazian, Robert A. Lad

SINCE it can be shown both theoretically'' : and experimentally that disordered Cu3Au has a greater internal energy than the ordered alloy, it might be expected that its chemical reactivity would be greater. Experiments were initiated' to test this hypothesis. This note will describe some recent results obtained in the study of the rates of corrosion of ordered and disordered polycrystalline Cu3Au by aqueous FeCl., The work of Robertson' has indicated that the attack by such solutions is intergran-ular and highly orientation dependent. It was of interest to see whether the order-disorder effect was great enough to overcome the variations from specimen to specimen which would arise from this type of attack. The polycrystalline alloy specimens (0.020 in. wire, 1¾ in. long) were preannealed in ½ atm H, at 700°C for 2 hr. The subsequent heat treatments to produce order and disorder were performed in M atm He. Disordered specimens were obtained by heating at 450°C for 2 hr and quenching in water. Ordered specimens were produced by heating for 2 hr at 450°, furnace cooling to 380°, and soaking at 380°C for 80 to 90 hr. Room temperature was reached by cooling to 150" at a rate never exceeding 7" per hr, and water quenching from 150°C. The specimens so produced exhibited electrical resistivities characteristic of the two states; of the order of 11.27x10 ohm-cm for the disordered, and 4.28x10 ohm-cm for the ordered specimens. The corrosion rates were studied at 30°C in ferric chloride solutions of several concentrations (?,¼, 1.5, and 1 molar). The specimens were attached to a stirrer during the tests. Tests were interrupted at intervals, and the specimen weight change was determined after washing and drying. Analysis of the solutions showed that the attack was limited to the copper. The higher corrosion rate for the disordered alloy, as illustrated in Fig. l, is typical of the results obtained. The effect of variation in ferric chloride concentrations is indicated in Table I for typical specimens. The variations in the ratio of reactivity for disordered and ordered specimens at the different concentrations are within experimental error, and the best value is estimated to be near 1.4. The experimental variation was due in part to the mode of attack, as mentioned, and in part to the fact that films were formed on the specimens under some conditions. Electron diffraction patterns of the films were very complex and indicated the presence of metallic iron, as did chemical analysis. In an attempt to eliminate the difficulties arising from the mechanism of attack, single crystal specimens were used. A greater reaction rate was again measured for the disordered specimens, but the reproduci-bility was no better than that for the polycrystalline metal. This would indicate that film formation was primarily responsible. It was concluded that the reaction with aqueous ferric chloride served to demonstrate that the reactivity of disordered Cu3Au is greater than that of the ordered alloy. However, the difficulties with film formation did not permit determinations of a precision great enough to warrant extension of the study to partially ordered alloy systems.

Jan 1, 1957

By F. P. Dewey

The first systematic attempt of the National Museum to gather material representing the economic geology and metallurgy of the country was made in connection with the Centennial Exhibition. The department may be considered as having originated then, althongh it was not formally inaugurated until December, 1882. Previous to the Centennial, all the illustrations of economic geology had been included in the mineral collection, and the illustrations of metallurgy were so very few that they had also been included with the minerals. When the museum began its collections for the Centennial, the subject of the mineral resources of tile United States was placed in the hands of Professor Wm. P. Blake, who was eminently fitted to undertake the work by his experience at various international exhibitions and his extensive acquaintance with the mining industry of the country. Professor Blake prepared a broad and exhaustive plan for this purpose, and the very large collection shown at Philadelphia was well calculated to set forth the vast mineral wealth of the country. The history of the department proper may conveniently be divided into three periods : first, the formative period, during which the Centennial material was mainly administered upon, ending Jnly 1, 1884, with the beginning of the preparation for the New Orleans Exposition; second, the New Orleans Exposition period, from July 1, 1884, to June 30, 1887, during which the collections for the New Orleans Exposition were made, exhibited at New Orleans, returned to Washington, and installed permanently in the museum; third, the southwest-court period, from July 1, 1887, to October 1, 1889, during which the collections were arranged in the southwest court of the museum.

Jan 1, 1891

By Gordon H. Chambers

MANGANESE ore is a true jack-of-all trades among industrial minerals, its only possible rival being iron ore. It is used in porcelain enamel, dry batteries, building brick, glazed pottery, floor tile, plastics, welding rods, chemicals, and varnish. You may be reading this through spectacles decolorized with manganese, and the light bulb above you contains some of this element. GEOLOGY Nearly all commercial manganese oxide deposits are of secondary origin; that is, they are concentrated by weathering from other manganese minerals more sparsely distributed in veins. The oxide minerals usually form irregular masses but in some places (Russia) they occur as beds of varying thickness and purity. Some manganese oxide bodies occur in soft gravel or clay formations but in other places the minerals are found in the form of veins and rounded nodules in limestone and other hard rocks. The geologic features of manganese deposits closely resemble those of iron deposits. Classification of the deposits is shown in the following table: I. Classification of manganese deposits based upon form of occurrence A. Stratiform masses 1. Oxides interlayered with sediments or layered volcanic or metamorphic rocks 2. Carbonates or silicates interlayered with sediments or layered volcanic or metamorphic rocks 3. Oxides, as surface bog deposits B. Veins and breccia filling 1. Oxides in larger part 2. Carbonates or silicates partly weathered to oxides C. Irregular masses 1. Oxides 2. Carbonates or silicates largely weathered to oxides D. Aggregates of small oxides in clay or weathered rocks 1. Mainly oxides E. Unclassified deposits II Classification of manganese deposits based upon mode of origin A. Hydrothermal deposits

Jan 1, 1949

By R. A. L. Black

13.8-1. Introduction. Table 13.8-1 shows that production from the African continent is an important part of total world mineral production. In three of the major particular resources listed, diamonds, gold, and cobalt, African production accounts for considerably more than half the world output. Overall, South Africa including South West Africa plays a dominant role in the mineral economy of Africa, other than in petroleum production. Table 13.81 also shows that much of the production is won by surface mining methods. In addition to the minerals listed in Table 13.8-1, Africa is a main world source for the following minerals: [Beryl 33% of total world production Columbium-tantalum 50%" " 1' Platinum group metals 20% l' " 11 Corundum 55%" " " 11 Vermiculite 30% (' " (6 Uranium oxide 15 0/, of free world production] South Africa and Rhodesia together account for nearly all of this production, except for columbium (niobium) of which Nigeria is the main producer. Thus the importance of southern Africa as a major mineral province can readily be appreciated. The consequences of serious political or military conflict between white-dominated southern Africa and the rest of the continent would be grave indeed, particularly for the West whose financial and economic interest in Africa as a whole is very large. The development of mineral resources in Africa involves the same basic elements as are involved anywhere else in the world: exploration, drilling and sampling, metallurgical assessment, and economic evaluation before, if it is justified, a prospect is brought to the productive stage. The same range of factors controls the economic viability of a project in Africa as elsewhere, of which the most important are:

Jan 1, 1968

By Robert Roberts

(Butte Meeting, August, 1913.) IN order to obtain data on the thermal effect of the blast-furnace jacket and oil the water consumption in these jackets a series of tests were run on the 56 by 180 in. blast furnaces at the Great Falls Reduction Department of the Anaconda Copper Mining Co., at Great Falls, Mont. The arrangement of the jacket is shown in the transverse section of one of the furnaces (Fig. 1) on which the tests were made. The nose, spout, and breast jackets have independent water supplies and discharges. The end and side jackets are connected in pairs, as regards water supply, the feed water entering at the bottom of the lower jacket and overflowing into the bottom of the jacket immediately above it, and discharging into an independent overflow pipe for each pair of jackets. Tests were run on the main side and end jackets, the breast jacket, the spout, and the nose. Measurements were taken of the quantity of water discharged per minute and the rise in temperature of the water in its passage through the jacket. The product of these two results, expressed in the proper units, evidently gives the number of units of heat removed per minute by the water. Sufficient work was done on each type of jacket to determine its behavior under different conditions, and the results from each set of conditions were checked by repeating the work from three to six times.

Jan 7, 1913

By W. E. D. Jr. Stokes

THE application of aviation to mining and petroleum operations, on the basis of economy and attainment, has become a demonstrated fact. According to Dominion Government records, 30 Canadian companies engaged in air transportation with northland mining camps, carried 13,000 tons of freight in 1935, and in 1936 carried 16,000 tons. In addition, many mining companies used planes to transport prospectors with canoes, outboard motors, gasoline drums and supplies to remote locations, and one company maintained a plane to take radium-bearing ore from its mine on Great Bear Lake nearly 1000 miles south to the rail-way at Waterways, Alberta. Heavy pieces of mining machinery weighing 2 tons are being carried by Ford trimotor planes over the Andes, at an altitude of not less than 15,000 feet. At Bulolo, New Guinea, 17,500 tons of disassembled gold-dredging equipment has been flown over inaccessible terrain, while supplies and building materials for a community of 1000 whites have been transported by airplane. A 31 z-ton shaft was carried on one notable trip, while at another time an automobile, 2 tons of rice and a large safe went over the mountains in one plane. Fig. 1 shows an electric generator that was carried by plane to Bulolo. Many large American oil companies operated fleets of planes during 1936, ranging from fast, luxurious air liners for executives to elaborate geological prospecting units, ambulance planes, freight carriers and pipe-line repair crews.

Jan 1, 1937

By J. S. Aronofsky, A. S. Lee

Results and experimental procedures are presented covering a preliminary laboratory investigation of the compaction of reservoir rocks and its effect on porosity and permeability. "Egective" compressibility was measured by subjecting core material to an overburden load and reducing pore pressure. Preliminary results showed relatively high effective compressibilities which varied from 1.8 X 10-' pore volume/pore volume /lb / in.~ for limestones to 7.7 X 10-6 pore volume/pore volume/lb/in.' and even higher for sandstone reservoirs conmining large amounts of fine clay material. It appeared from the initiol results that the effective compressibility of the material could not be correlated directly with porosity and that other factors, such as the amount of clay material present might have to be taken into account. The work to date has indicated that effective compressibility factors will have to be measured for the particular reservoirs heing studied. Oil permeability of core materid was measured under various effective overburden loads from 0 to 8,000 psi. It has been found than reduction of permeability in clean sands was relatively small and the results agreed with published data. For sandstones containing large amounts of clay, preliminary tests indicated very large reductions in permeability with increasing effective overburden pressures. It is planned to continue laboratory work on this phase because of its importance in low-permeability reservoirs. INTRODUCTION During the past few years increasing interest has been shown in the differences obtained between conventional laboratory measurements on cores at atmospheric pressure and those when reservoir conditions are simulated. Since these data are used as the basis for calculations and the prediction of reservoir behavior, their evaluation under reservoir conditions is most important. The effect of the compressibility of the rock upon the reservoir behavior, as fluid pressure declines, is an important subject which has been insufficiently studied. The total pressure on any plane through a reservoir is the result of the grain-to-grain rock pressure due to the overburden and the pressure of the interstitial fluid on the plane. As reservoir fluid pressure declines, the net load on the rock phase must increase, and the result is the compaction of the rock structure which produces a decrease in pore volume. Simultaneously, the rock grains expand into the pore space as the fluid pressure declines. The result of these two effects is defined as the effective compressibility of the rock and is expressed in units of pore volume/original pore volume/psi. Work was started by Imperial in 1954 on the effects of pressure on the porosity of reservoir rock. These studies established effective compressibility factors for some limestones and dolomites. Since that time effective compressibilities have been obtained for other Canadian and some U. S. reservoir rocks. In conjunction with the study of porosity, an investigation has also been initiated to determine the effects of pressure on permeability. One outcrop and several reservoir sandstone cores have been tested to date. ROCK COMPRESSIBILITY Apparatus anD Procedure A diagram of the apparatus used in these studies is shown in Fig. 1. The equipment was constructed so that a uniform pressure, equivalent to the reservoir overburden, could be applied by the oil pump and transmitted on all sides of the core through the Lucite sheath. The sample was completely saturated by circulating brine through the mounted core. Pressure in

By J. Washburn

Two simple types of dislocation distribution were introduced into zinc crystal specimens and the effect of each on the stress-strain curve was investigated. Quantitative results were obtained for simple edge dislocation arrays and for an array of screw dislocations lying in the slip plane. A CCORDING to present knowledge, the disloca-tions present in large annealed metal crystals can be divided into two somewhat arbitrary groups: 1—single dislocation lines distributed more or less at random or forming elements of a three-dimensional network in which the distance between adjacent dislocations is of the order of 10 2 to lo-' cm and 2— widely separated planar arrays of edge dislocations forming dislocation walls or small angle boundaries within which adjacent dislocation lines are spaced at much smaller distances (lo-' to 10- hm). The former can be considered as a dislocation interpretation of the mosaic crystal proposed by Darwin and Ewaldl, ' 40 years ago to account for anomalously high integrated intensities of X-ray diffraction maxima. Small angle boundaries, although now known to be present in most single crystals used for mechanical testing, were not generally recognized by the early workers. This was partly due to the fact that only recently have improved X-ray and metal-lographic techniques been available for checking the macroscopic perfection of crystals."" It has long been known that changes in growth conditions and in annealing procedure, which might logically be expected to cause variations in the structural details of both the dislocation network and of dislocation boundaries, produce marked variations in some mechanical properties such as yield strength." However, no quantitative experimental correlations between changes in dislocation distribution and changes in mechanical properties have yet been made. Such a correlation has been difficult to obtain because, even when great care is exercised to keep the histories of a number of single crystal specimens identical, it usually has not been possible to avoid considerable variation in macroscopic per- fection.' The number and orientation of dislocation boundaries vary from specimen to specimen. This has probably been an important contributing factor to the large scatter in the results of most mechanical measurements on pure single crystals. Some recent experiments"% ith single crystals of zinc have shown that the presence of dislocation boundaries in a specimen can increase its resistance to deformation by slip. With polycrystalline aluminum and nickel, there is also evidence that dislocation boundaries within the individual grains of the aggregate can increase the resistance of the material to plastic deformation, either as measured by tension tests at room temperature or by creep tests at higher temperatures.'" " Although the foregoing observations seem to have established the fact that substructure can have a strengthening effect, the test conditions were too complex to give much information concerning the mechanism. In the foregoing cases, a network of intersecting boundaries having various orientations and boundary angles were present. Before their apparent strengthening effect can be understood, it will be necessary to isolate and study separately the effect of a number of variables: 1—boundary angle, 2—boundary orientation with respect to the active slip direction, 3—number of boundaries, 4—intersections of boundaries, 5—detailed structure of the boundaries, and 6—interaction of impurity atoms with dislocations in boundaries. The object of the present work was to study the effect of dislocation boundaries on flow stress under the following simple experimental conditions: 1— substantially pure shear deformation and 2—boundaries of controlled angle, orientation, and number. In this way, it might be possible to distinguish the important variables from the relatively unimportant ones. Experimental Procedure Stress-strain curves of hexagonal metals are generally nearly linear even out to very large strains."

Jan 1, 1956

By B. K. Larkin, H. R. Bailey

A model Of heat flow in an underground combustion process is studied. This model includes convection effects and thus is more general than previous studies which considered conduction as the only mechanistn for heat transfer. Both linear (tube run) and radial (field application) geometries are considered. The effects of ignition heaters, vertical losses and finite source width are considered for the linear case. The results are in the form of equations and are presented in graphical form for a number of cases. Convection effects increase frontal temperatures about 25 per cent over those computed for conductive transfer for typical field operating conditions. This increase in temperature is a result of heat being transported toward the front by the injection gas. Even greater temperature increases are realized as the per cent oxygen in the injection gas decreases. It is well known that compression costs are of considerable importance in estimating the economic feasibility of underground combustion. By assuming an ignition temperature for the combustion fuel, predictions of limiting conditions on fuel density and injection rate necessary to sustain the combustion zone are made. For typical field conditions, at least 0.75 lb/cu ft of fuel are needed with air as the injection gas. If the injection gas is 10 per cent oxygen and 90 per cent nitrogen, this figure is 0.69 lb/cu ft. INTRODUCTION The possibility of increasing oil recovery by underground combustion has been considered for many years. Recent field tests indicate that the underground combustion process is technically feasible. The economic feasibility depends to a large extent on the amount of air which must be injected to sustain combustion. Prediction of the success of employing underground combustion in a particular reservoir must be based on existing field tests, laboratory tube runs"' and solutions of mathematical or analog models. Vogel and Krueger5 devised an electrical analog of the heat transfer problem in an underground combus-ion process. They considered the problem of heat conduction from a cylindrical source with increasing radius assuming no vertical losses. Bailey and Larkin and Ramey solved the corresponding problem including vertical losses by considering a mathematical model of the conduction process. Ref. 9, 10 and 11 also present information related to the subject study. The present paper generalizes these results to include both conduction and convection mechanisms for heat flow. A model of the conduction-convection process is described. The partial differential equations governing this model are written and solved for a number of cases of interest. The formulas are evaluated and the results are presented graphically. A CONDUCTION-CONVECTION MODEL Description of the Model A number of models are employed in this paper, each of which approximate a particular physical situation depending on the geometry, i.e., linear or radial flow, the type of vertical heat losses, the nature of the source, etc. The geometry for both the linear and radial case is shown in Fig. 1. A particular linear model is described in this section, and variations from this model are described in later sections of the paper. Consider a homogeneous, semi-infinite porous prism with lateral sides insulated as shown in Fig. 1. The left end, x = 0, is heated for a time t, with a plane heater supplying a constant heat flux and during this time; gas (nitrogen) is passed through the pores of the prism at a constant mass flux. At time t, the heater is turned off and air is injected in place of the nitrogen. This causes combustion to take place, and a uniform source of width 1 is formed which moves at a constant velocity v, to the right. The frontal velocity v, is related to the gas velocity v,, through stoichiometric considerations

By G. L. F. Powell, L. M. Hogan

Large degrees of undercooling have been produced in bulk samples, 400 g, of copper and Cu-O alloys by melting in a slag of commercial soda-lime glass. The maximum degrees of undercooling obtained for copper, hypoeutectic and hypereutectic Cu-O alloy samples were 208°, 218°, and 97°C, respectively. No grain refinement as a function of undercooling was observed for the pure copper samples although in Cu-O alloys there was a marked decrease in grain size at degrees of undercooling greater than 150°C. The grain size change is the result of recrystallization during or immediately following the freezing process. THE first report of a large degree of undercooling in a bulk sample of metal was that by Bardenheuer and Bleckmann1 who produced 258°C undercooling in a 150-g sample of iron by melting in a glass slag. Garbeck2 extended this technique to nickel, cobalt, and copper and reported maximum undercoolings of 220°, 230°, and 60°C, respectively, while Fehling and schei13 undercooled a large number of metals as 2 to 20-g samples slagged in glass. Subsequently, one of the authors4 applied the glass slag technique to bulk samples, -500 g, of silver and obtained a maximum undercooling of 250°C. It was concluded that impurities which normally catalyze nucleation at small degrees of undercooling could be removed by oxidation and solution in a glass slag. Large undercooling of bulk samples of iron, nickel, cobalt, and their alloys has also been reported by other authors.8'10'11 Of the five metals mentioned above, copper was the only one which had not been undercooled by at least 200°C in the form of a large bulk sample. Since copper exhibits high liquid solubility for oxygen, as do iron, nickel, cobalt, and silver, it was considered that a much larger degree of undercooling than that observed by Garbeck for copper should be possible. This was obtained by modification of the technique applied previously to silver and the results of undercooling experiments with 400-g samples of copper form part of this paper. The undercooling behavior of Cu-O alloys was also studied, and the influence of a small oxygen content on the grain structure of undercooled copper was observed metallographically. 1) EXPERIMENTAL The copper was obtained as oxygen-free high-conductivity copper, the major impurities of which were Fe 0.01 pct, Zn 0.015 pct, and Si 0.02 pct. Melting was carried out in an open-ended vertical cylindrical fur- nace wound with Kanthal wire. A schematic diagram of the experimental setup is shown in Fig. 1. The undercooling technique previously used for silver4 involved preoxidation of the samples by melting the silver in contact with the atmosphere. The oxygen content was subsequently reduced by freezing the samples under a glass slag, whereby the oxygen was evolved as gas and the continuous glass cover over the surface prevented re-solution of oxygen when the sample was remelted. Since oxygen is not released as gas when a Cu-O alloy is frozen. the technique had to be modified for use with copper. Also, copper is oxidized during fire refining so that an in situ preoxidation treatment of the samples was not considered to be a prerequisite to large undercooling. Experimentation proved that this supposition was correct. Instead, it was found that care was necessary during melting of the copper under glass to minimize oxygen pickup. Samples of copper weighing 400 g were prepared by adding 50-g pieces of copper to a vitreous silica crucible partly filled with soda lime glass at a temperature of approximately 1000°C. Each piece was quickly immersed in the glass slag and held at this temperature until the oxide coating on the surface decomposed. This change was easily observed and coincided with the formation of gas bubbles in the glass

Jan 1, 1969

By A. D. McMaster, M. L. Gimpl, N. Fuschillo

There is interest in the use of rhenium metal films as resistive elements in thin-film circcits, and already some zvork has been done using er)aporated rhenium films. It has been found that rheniim films protected from the atmosphere by an evaporated layer of silicon monoxide show excellent electrical stability. Unprotected films, however, are subject to aging- effects, notably the increase in electrical resistivity as a function of time. This phenomenon can be understood as primarily one of oxidation of the thin films. This paper is concerned with the study of the oxidation and crystallization behavior of such unprotected films. It has been found that the oxidation rates are a function of the substrate temperatures used during the deposition of Lhe metal films. The strictures observed in the films are correlated with the film resistivities and some data are presented to establish the existence of the various types of oxides of rhenium. ThERE is some interest in the use of thin films of rhenium metal as resistive elements in monolithic, thin-film integrated circuits. Some work has been done using evaporated films and it has been found that such films, if protected from the atmosphere by an evaporated layer of silicon monoxide, show excellent electrical stability up to temperatures of 500"." Rhenium films unprotected from the atmosphere tend to age and the electrical resistivity of the films increases as a function of time. Rhenium films, of the order of <100A thick, prepared by electron-beam evaporation techniques are found to oxidize very readily when exposed to dry air at room temperature. It would seem, therefore, that this aging phenomenon could be attributed to the oxidation of the metal films. In this investigation, the oxidation and crystallization behavior of thin films of rhenium evaporated onto silicon monoxide substrates were studied as a function of the substrate temperatures used during the evaporation. The films were examined using electron-microscopy and electron-diffraction techniques. EXPERIMENTAL RESULTS Rhenium metal was evaporated onto suitable prepared substrates which were heated to various temperatures. The evaporations were performed in a vacuum of approximately 5 x 1CT5 torr. The evaporation was carried out at a rate of approximately 10A per omin. The final film thickness was approximately lOOA and the resistance ranged from 5000 to 10,000 ohms per square. The substrates used for supporting the metal films were made by evaporating 75A of silicon monoxide onto freshly cleaved mica. The silicon monoxide film was then floated off the mica by immersing the composite in water. The film could then be picked up on a clean nickel grid. Silicon monoxide substrates were chosen because of their similarity to quartz and glass substrates commonly used for making thin-film resistors. Fuschillo, Gimpl, and McMas-ter have also shown that silicon monoxide films have only minor structural changes at temperatures up to 800°C. This fact simplified the interpretation of any changes observed in the electron micrographs or electron-diffraction patterns obtained from the deposited rhenium films. After the evaporations were completed, the substrates were cooled to room temperature, except where noted differently, before the coated substrates were removed from the vacuum system. All aging of the deposited films was done in a desiccator. The evaporated films were examined in an electron microscope equipped with a hot stage that would permit continuous observations of the samples up to temperatures of 1000°C. RESULTS A series of electron micrographs of the rhenium films deposited on the silicon monoxide substrates are shown to Figs. 1 to 3. In all cases, the metal films are approximately 100A thick and the micrographs were taken 1 hr after the deposition was completed. here was no apparent structure in the films deposited on the substrates held at the higher temperatures. The

Jan 1, 1967

By L. Luini, E. Lee

An exploratory survey of the heat treatment response of commercial titanium alloys (Ti-150A, RC-130B, and MST 3AI-5Cr al-loys) shows a wide range of possible hardness and microstructural characteristics. The hardening is primarily dependent on the solid state transformation of the phase. An age hardening reaction which apparently is associated with ß decomposition and precipitation has been shown. Brittleness and notch sensitivity appear to be characteristic of age hardening to high hardness. Ductility, tensile strengths, and elongations are given. A NUMBER of commercially produced titanium-base alloys have been made available by the titanium metals industry. These alloys were developed to combine the light weight of titanium with increased strength through alloy additions. Usually the properties of these alloys are reported for material in the hot rolled and annealed condition. Since the production of commercial titanium has preceded the investigation of titanium-base alloy systems, the potential of these alloys is not well known. Although heat treatability has been indicated for these alloys, data on the response to heat treatment are quite limited. The heat treatability of titanium is based on the allotropic transformation of the high temperature, body-centered cubic ß structure to the low temperature, hexagonal close-packed a structure at approximately 1625 °F. This transformation in the pure metal is of little practical significance in heat treatment since the high temperature phase is not amenable to controlled transformation. Alloy additions serve to alter the transformation kinetics and permit control of the transformation by heat treatment variables. The effects of different alloys on the allotropic transformation in titanium classify them in two general categories,1 a stabilizing and ß stabilizing elements. The a stabilizers, represented by aluminum and oxygen, raise the temperature limits of the low temperature phase and introduce a two-phase a + ß temperature range. The ß stabilizers, represented by molybdenum and columbium, lower the equilibrium temperature of ß and give rise to an extended temperature range where both a and ß phases are stable. Another type of ß stabilizer, represented by iron, chromium, and manganese, introduces a eutectoid reaction. Some commercial titanium alloys belong to complex multiple element systems. Based upon the phase diagrams of the binary systems, the general effect of commercial compositions is to vary the stability of the high temperature phase and significantly alter its transformation characteristics. Therefore it is expected that the characteristics of alloyed titanium can be altered by heat treatment. The present investigation was undertaken to survey the variations in hardness, microstructure, and mechanical properties as affected by heat treatment variables. Commercial Alloys lnvestigated The commercially available titanium-base alloys selected for this investigation and obtained as 3/4 in. diameter hot rolled and annealed bars are listed in Table I. The producer did not determine the chemical composition of the Ti-150A heats X1052 and L685. The early heats of Ti-150A, prefixed with the letter X, were melted with tungsten-tipped electrodes and cast in approximately 500 lb ingots 12 in. in diameter. The heats prefixed with the letter L were melted under a revised melting practice yielding approximately 1300 lb ingots 16 in. in diameter. The final annealing treatment was at 1200" to 1250°F for 1 hr. The MST-3A1-5Cr alloy was melted in an induction furnace and cast in 7 in. diameter ingots. This practice produces high carbon material and some variation in the amount of carbides was found in different sections of the same bar. The RC-130B alloy was melted with a carbon arc. This alloy showed approximately 2 pct carbides. No large segregation effects were observed.

Jan 1, 1955