Search Documents

By J. J. Hauser, H. C. Theuerer

A cathode sputtering technique is described which elin7inates the need for ultrahigh vacuum in preparing thin films of materials sensitive to gaseous impurities. This technique uses a fraction of the atoms sputtering within an anode container to getter actice gases, such as HzO, Oz, and Nz. The gases alzd gettering metal are deposited on the container walls, thus shielding the coating zone of the system from contamination. The use of the method for preparing superconducting-normal metal couples such as Ph-Cu and Ph-Pt is described, and the properties of the individual and composite films are given and discussed. GETTER sputtering is a method which greatly simplifies the preparation of thin films in cases where composition control is critical. A major difficulty with conventional sputtering and other vacuum-deposition techniques is the contamination of the forming film caused by residual gases, such as H20, CO, Oz, and Nz, in the coating equipment. The difficulty arises from the fact that even when the residual pressure in the system is as low as 1 x 10"6 Torr, with a deposition rate of 10A per sec, there are as many contaminating gas collisions with the substrate as there are with film-forming metallic atoms. It is not surprising, therefore, that with reactive metals, such as tantalum and niobium or with semiconductors, such as silicon and germanium, films with properties far different from the starting materials are obtained. In the case of niobium and tantalum, deposited either by sputtering or vacuum evaporation in systems with reactive gases at pressures of the order of 1 x l0-' Torr, the loss of superconductivity is traceable to interstial oxygen or nitrogen. On the other hand, working in vacuum of the order of 1 x l0-" Torr, Marchand and enema' have shown that superconducting films of tantalum with properties approaching those of bulk material are possible. At this level of gaseous impurities -lo6 metallic atoms arrive at the substrate before a contaminating collision occurs again assuming a deposition rate of 10A per sec. It is evident from the above that any successful vacuum technique requires the elimination of reactive gases from the region of the system where coating is occurring. Getter sputtering accomplishes this using conventional vacuum equipment with residual pressures in the 106 Torr range. In fact? vacuum systems with residual pressures of lo-" Torr are adequate for most purposes. With this method, sputtering is confined within an anode can and, by geometric design, sputtering itself is used to purify the argon at the lower and upper parts of the system by the gettering action of the reactive metal. In consequence, the central region of the system where coating occurs is shielded from gaseous contamination. Getter sputtering is particularly useful for the preparation of alloy and compound films. With this method, if a cathode of homogeneous composition is bombarded with high-energy argon ions, transfer of material to the substrate having the same composition as the cathode will occur. This is true after an initial equilibration time, even though the constituents of the cathode may have different sputtering rates. During equilibration, the surface of the cathode changes composition due to differences in sputtering rate, but mass conservation demands a steady-state condition such that the atoms sputtered from the surface have the same composition as the cathode material from which the surface is generated. GETTER-SPUTTERING APPARATUS The original form2 of the getter-sputtering apparatus is shown in Fig. 1. It consists of a closed nickel or stainless-steel can 4 in. tall and 2-3/8 in. in diameter. Mounted symmetrically from each end

Jan 1, 1965

By P. E. Arnold, G. S. Ansell

RELAXATION in metals has been studied in detail by many workers in recent years.1-5 These studies have shown that there is an energy-loss peak observed in a metal placed in mechanical resonance at low frequencies which may be correlated with various metallurgical processes. These experiments have been largely used to study single-phase materials. In order to study the effect of a finely dispersed second phase in a metal matrix upon this phenomenon, the relaxation behavior of an aluminum-aluminum oxide SAP-Type alloy in both the fine-grained as-extruded and coarse-grained recrystallized conditions was investigated by the use of internal-friction measurements. The alloys studied, designated MD 2100, consist of a matrix of commercial-purity aluminum containing a finely dispersed second phase of aluminum oxide. The aluminum oxide is present in this alloy in the form of fine platelets approximately 130A units thick and several microns on edge. The mean free path betwen dispersed platelets is approximately 0.5 p. The grain size of this alloy is extremely stable at temperatures as high as the melting temperature of the aluminum matrix. In the as-extruded condition the grain diameter is several microns, while in the recrystallized condition it is several millimeters in diameter. The damping characteristics of the alloy samples were determined using a torsional-pendulum device. The internal-friction constant was determined for this alloy in both the fine-grained as-extruded and coarse-grained recrystallized conditions over the temperature range from 343" to 923°K at frequencies of 0.9, 1.3, and 1.8 cycles per sec. An internal-friction peak was observed in testing the fine-grained alloys which was not observed for the coarse-grained alloys. This peak, which might be associated with a type of grain-boundary relaxation, was observed at each of the three different test frequencies for the fine-grained sample. The temperature at which the relaxation peak occurred for each of the three different frequencies is shown in Table I. From these data an activation energy of relaxation for each pair of frequencies was determined by comparing the temperature shift of the relaxation peak with frequency between each of the test frequencies, assuming that an Arrhenius-type rate equation is applicable. The activation energy of relaxation determined from these data is also shown in Table I. The mean value of the activation energy was about 6 kcal per mole. The activation energy for the relaxation process determined in this investigation indicates that the relaxation associated with the grain boundaries in this aluminum-aluminum oxide SAP-Type alloy is quite a different process than grain boundary relaxation in single-phase aluminum alloys. In these latter alloys, the activation energy for relaxation has been found to be the activation energy for self-diffusion, approximately 36 kcal per mole1,2 Where the activation energy is the same as the activation energy for self diffusion, it has been proposed that the relaxation phenomena is dependent upon vacancy formation and motion. It is apparent therefore, that, in this aluminum-aluminum oxide SAP-Type alloy, the relaxation must be due to another type of atom transport. It has been shown previously in studies of the high-temperature, low-stress, steady-state creep behavior of as-extruded aluminum SAP-Type alloys, that the activation energy for steady-state creep is one that may be characterized by the nucleation of dislocations from the grain boundaries. It is proposed that the relaxation behavior observed here is due to a similar effect. In this case, the internal-friction peak is a resonance behavior due to the time-dependent nucleation of dislocations from grain boundaries in the sample. A process of this type would have an activation energy which is undoubtedly stress-dependent and of the form Q = Q, + (dQ/du)u

Jan 1, 1962

By A. H. Cottrel

SINCE metallurgy exists to provide strong, tough, engineering materials it must inevitably be perpetually concerned with the problem of brittle-ness. The steel-making industry was created because chemically unrefined iron is brittle. The steel-working and alloy-steel industries exist partly because hardness and ductility are mutually exclusive qualities in structurally unrefined steel. Yet, in spite of these immense industries, the brittle failure of steel ships hulls, bridges, pressure vessels, and pipelines, is still a contemporary problem. In fact, brittleness is a normal property of most solids, including metals and alloys, at low temperatures. Only face-centred cubic metals are commonly ductile at the lowest temperatures, and even here exceptions are known.'," Expensive are-melting processes. under inert gases or vacuum, have been developed to overcome brittleness in titanium, zirconium, columbium. and molybdenum. Polycrystal-line zinc, magnesium, and uranium have little ductility at room temperature. Beryllium, chromium, and tungsten have even less; similarly for antimony, bismuth, germanium, silicon, intermetallic compounds, and metallic carbides, nitrides, silicides, and borides. Oxides and other ceramics would be ideal creep-resistant materials but for their extreme brittleness when cold, and great efforts have been made to overcome this problem by mixing ceramics with metals. In fact, the traditional use of the name metallurgy for what is really the science of engineering materials is a recognition that most non-metallic solids have so far been precluded, by their extreme brittleness, from use as major structural materials in mechanical engineering. Most of what we know about brittleness in metals has come from studies of structural steel, and it is this material that shall mainly be considered. The things we have learned from it have a wider application, at least to other body-centred cubic transition metals, although the extent to which similar ideas can be applied to hexagonal metals and other materials is not yet clear. Fracture and Plastic Deformation The theoretical breaking strength of an ideal solid, about E/10 where E is Young's modulus, has been approached reasonably closely in experiments on fibres. But large specimens break at much lower stresses. For example, brittle cracks in large structural steel assemblies have been observed to spread catastrophically at speeds of 6000 ft per sec under stresses of about 10,000 psi, i.e. about E/3000. There are two sources of weakness; stress concentrations, and chemical agents in grain boundaries or on crack faces that lower the surface energy y of the material. Although we shall deal mainly only with the first of these, much of the discussion is also applicable to the second when different values of y are used. Griffith's well-known formula p = [ 2Ey/p(1 - v2)c]1/2 [1] gives the smallest tensile stress p able to propagate an atomically sharp surface crack of length c or interior crack of length 2c through a thick plate (compared with c) of elastically isotropic material of

Jan 1, 1959

By Torres S. Ricardo, Encina M. Víctor, Segura O. Claudio

INTRODUCTION This paper is a conceptual resume of engineering studies that have been evaluated by the Mine Department related to production planning over the next twenty-five years. These studies have been required principally because: a) The Rio Blanco Mine, property of CODELCO- CHILE, Andina Division, faces an operational problem due to heavy snowfall in winter which enters the surface subsidence area of the cave; later melts and filters into the broken ore creating a product that is difficult to transfer through the orepasses. The phenomenon is especially serious during the spring and has been increasing over the years. This element that complicates extraction will be controlled with the procedures proposed or others that may be determined in the future. b) The mine will increase production in 1985 by 40% . LOCATION The deposit is located in the central region of the Andes Cordillera, at an altitude of approximately 3,600 m above sea level, 50 km to the northeast of Santiago. The main camp is Saladillo (at 1,300 meters above sea level) located 30 km from the mine. Due to its location, the mine is subject to heavy snow storms during the year. On many occasions the road from Saladillo to the mine is closed because of storms and avalanches. For this reason the company has self-sufficient civil facilities near the mine to cover the needs and welfare of the working force. These housing facilities are connected to the mine by underground passages. For the same weather related reason the primary and secondary crushers, and the entire concentrator complex are located underground. GEOLOGIC CHARACTERISTICS Geology Based on the geologic model developed for the Rio Blanco deposit and comparing it with standard models pertaining to copper porphyries, it can be concluded that this deposit is part of the apical sector of a mega deposit and therefore the projections of the Xio Blanco cop per mine are very favorable, both in lateral area and depth. In order to confirm and evaluate these geo- logic features, an extensive drilling program was started at the Rio Blanco deposit. Diamond drill holes were drilled to depth as well as in the areas named "La Americana", "Don Luis" and "Elguin". The area explored by the drill program is 3 km long in a north-south direction and 1.5 km wide in an east-west direction. In some sections the drilling in depth reached the 2,300 m elevation mark. The lowermost level in the mine is at elevation 3,070 m. These new studies have permitted the recognition of the following lithologic units: Andesite Andesite Breccia Granodiorites, Rio Blanco and Cascada Granodiorite Breccia Quartzmonzonite Porphyry Monzodiorites and Latites Tourmaline Breccia Dacite Pipe and Rhyolite marginal ring. The mineralogical study permits the definition of three stages of hypogene and hydroterma1 alteration of importance with a time-altered sequence. These stages correspond to a late hydrothermal stage. The kinds of alteration that have been recognized are: Potasic Alteration Propylitic Alteration

Jan 1, 1981

By R. J. Hafsten, E. S. Davenport, R. A. Grange

THE influence of austenite grain size upon the hardenability of steel is now fairly well understood; for a given austenite, increasing the grain size increases the depth of hardening, and, since the latter is related to the fundamental transformation behavior of austenite, it follows that austenite decomposition must, in general, be retarded by increasing grain size. To date, very little quantitative information bearing directly on the effect of austenite grain size upon the progress and result of isothermal transformation has been published. Davenport and Bain,1 and Zimmerman, Aborn and Bain2 have shown that the transformation is definitely retarded in hypereutectoid plain carbon steels at temperatures near and above the upper region of rapid transformation (Ar') when the austenite grains are increased in size. More recently, Griffiths, Pfeil and Allen3 investigated the effect of a series of different heating (austenitizing) temperatures upon the progress of isothermal transformation at 1245°F. (675°C.) and 745°F. (395°C.) in a medium carbon, low-alloy steel; while they reported no measurements of the austenite grain size, their results suggest that increase in grain size retards austenite transformation at 1245°F. (675°C.), but has no appreciable effect at 745°F (395°C.). The present paper deals with the results of a study of the isothermal transformation of austenite in a single commercial alloy steel in which a fine-grained or a coarse-grained state was induced by appropriate selection of austenitizing temperature. The data are presented in the form of isothermal transformation diagrams, which clearly show that coarsening the grains lessens the rate of transformation of austenite to proeutectoid ferrite and pearlite-that is, at temperature levels above about 1000°F. (540°C.)-but is without significant effect at lower temperatures where the transformation product is bainite or martensite. It is to be presumed that the foregoing statement would be valid, at least in principle, for many other grades of steel; it confirms again that the mechanism of transformation to a pearlitic structure is fundamentally different from that to an acicular structure. A number of related observations were made, which seem to throw some light on the transformation process as it takes place in alloy steels, particularly at temperature levels in the vicinity of 1000°F. (540°C.), where the transition from lamellar to acicular structures occurs. These data are discussed briefly in the belief that they may lead to a clearer understanding of this aspect of the subject. MATERIAL AND EXPERIMENTAL PROCEDURE The material investigated was a commercial grade of S.A.E. 4140 steel, the composition of which was as follows: 0.37 per cent C, 0.77 per cent Mn, 0.98 per cent Cr and 0.21 per cent M0. It was hot-rolled to a 1 1/8-in. round bar and normalized by air-cooling from 1800°F. (980°C.).

Jan 1, 1941

By J. B. Chatelain, M. F. Dufour

FLUID jet mills, employing a compressible fluid to grind materials to the subsieve range, was developed in the early 1930's, and the subsequent acceptance of these units was the result of their ability to pulverize solids that, because of physical properties, could not be processed by other attrition methods, such as ball, pebble, and hammer mills. Also, the fluid energy pulverizer is the only grinding device that will discharge continuously a 5-micron or smaller product. Simultaneous ultra-fine grinding and classification is the widest application of this unit. Jet mills may be used to advantage to reduce particle size of solids suspended in liquids, for coating one material with another, and effecting chemical reactions and changes in physical characteristics other than a reduction in size. Materials that can be processed by this grinding method include nonmetallic and metallic minerals, ores, metals, pigments, insecticides, fungicides, pharmaceuticals, plastics, dyes, and numerous other organic and inorganic products. Grinding principles utilized in the fluid mills available on the market are basically the same, the major difference being in the shape of the, grinding and classification chamber. Grinding in fluid jet pulverizers is accomplished by collisions between particles of the material being ground with the energy being supplied by compressed fluids entering the grinding chamber at high velocities. The "Micronizer" is a fluid energy mill employing a relatively flat cylindrical grinding chamber. Fig. 1 shows general construction details. The mill shown is equipped with a venturi type feeder using a compressed fluid to inject the feed into the grinding chamber. The energy consumed in forcing the feed into the grinding chamber against the mill pressure is, in some cases, as much as 40 pct of the total required for processing. Recent improvements, using a compression screw feeder as shown in Fig. 2, can reduce this to 1 or 2 pct of the total energy requirements. Grinding Grinding, as carried out in the. Micronizer involves the action of gaseous jets emerging from nozzles located in the peripheral wall of the grinding chamber. The axes, of the jets are tangential to a circle of smaller diameter than the grinding chamber as is shown in Fig. 1, and the gases entering the chamber maintain a high rotational velocity. The feed introduced into the mill is accelerated by the rotating gases and is thrown to the outside where a portion, coming in the zone of action of a nozzle, is further accelerated tangentially and inward. Violent collisions occur between the particles so accelerated and other particles circulating at a slower rate in a thin band near the periphery. It is estimated over 90 pct of the reduction in Micronizers occur as a result of impact within a fraction of an inch of the orifice. Observations also indicate that size reduction is independent of any interaction with the walls of the

Jan 1, 1952

By R. L. Slobod, B. H. Caudle, R. A. Erickson

In predicting the sweepout pattern efficiency to be expected in a .secondary recovery operation, the reservoir engineer is often confronted with a situation in which part of the producing formation lies between the last row of wells and the reservoir boundary. To date, there has been little or no reference in the literalure to sweepout pattern efficiencies in such areas. This paper presents the results, of a laboratory study in which the area contacted around the edge of a reservoir injected in a five-spot pattern was determined. The X-ray shadowgraph technique was used in this study. It was found that surprisingly large portions of the reservoir area lying outside the well network are conracted by the injected fluid before, abndonment conditions are reached. In fact, it can he said that at least 00 per cent of the circa lying outside the last row of wells and within a distance of one well spacing of these wells will ultimately be contacted by the injected fluid in the case of most water floods. Frorn the results given in this paper, it is possible to estitilate not only the extent to which encroachment into these areas will occur but also the injection volume necessary to produce the wells to abnndonment conditions. INTRODUCTION While considerable work has hern done in recent years1.?.'.''.' evaluating the fraction of the reservoir contacted as a function of the mobility ratio for several different well patterns, there has been practically no mention of what happens to the oil in that portion of the reservoir which lies between the last row of wells and the reservoir boundary. In fact, the assumption is generally made that little or no recovery can he expected From this area. This assumption is incorrect and in many cases will lead to seriouq errors in calculating reservoir performance. The fraction of the area outside the regular well pattern contacted in a five-spot injection system has been studied using the X-ray technique5 to follow the progress of actual floods in porous models of reservoir elemental areas. In this paper, the method for carrying out such a study and the results showing the fraction of the area in question swept as a function of mobility ratio and the produced fluids are presented. THE REPRESENTATION OF A RESERVOIR BY ITS ELEMENTAL AREAS She portion of the reservoir lying between the edge of a reservoir and a line connecting the outermost wells may be roughly designated as the part of the reservoir outside the regular well pattern. An example of such an area is shown as the shaded portion in Fig. 1. The case of a square reservoir utilizing a five-spot injection program and with one full well spacing between the outermost wells and the boundary (Fig. 1) was selected as the single example which would provide the most insight into

Jan 1, 1956

By J. R. Jargon, H. K. van Poollen

Non-Newtonian fluids may be injected into a reservoir during secondary recovery operations. The non-Newtonian fluid used in this work is a power-law type of fluid that is, the viscosity of the fluid decreases as the flow rate or rate of shear increases. This paper presents equations for steady-state linear and radial flow of such fluids, transient behavior results from a finite difference model of a radial system, and transient behavior results from a field test. The equations that describe the flow of a non-Newtonian fluid are non-linear and are solved numerically. Finite difference solutions are presented as curves of dimensionless pressure drop at the wellbore us dimensionless time for a constant injection rate. Solutions were obtained for 5-percent, 10-percent and 100-percent PV of a non-Newtonian fluid for injection rates of 1, 10, 100 and 1000 cc/sec and for a 5 percent PV of non-Newtonian fluid located at T = Tw' 3, 10, 20, 50 and 100 ft for a flow rate of 1 cc/sec. The buildup curves do not exhibit a stmight-line portion as is the case for Newtonian flow through porous media. Correlations also are shown for the productivity index vs rate for the computer model study and the field tests. INTRODUCTION During various secondary recovery operations non-Newtonian fluids are injected. Such fluids, in general, include thickened water and gelled fluids. The term "non-Newtonian" implies that the viscosity is not only dependent upon temperature and pressure, but also on the rate of shear that is applied to the fluid. For example, water, which is a Newtonian fluid, will have essentially the same viscosity no matter what rate of shear is applied. A pseudo-plastic fluid exhibits a decreasing viscosity when higher rates of shear are applied; a dilated fluid has an increasing viscosity with increasing rates of shear. The objective of studies performed and described in this report is to obtain relationships and mathematical and empirical descriptions of the flow of non-Newtonian fluids through porous media. Simple mathematical relationships, computer studies that include the unsteady-state behavior of such fluids, and field tests are used. PREVIOUS LABORATORY STUDIES Laboratory studies have been performed by several investigators. The fluids used in one investigationl were surfactant-stabilized dispersions of water in hydrocarbons. Its Fig. 6 is reproduced as our Fig. 1. This effective-viscosity vs frontal-velocity diagram shows that this fluid is of the power-law type over a fairly large range of frontal velocities. Gogartyl developed an equation for the effective viscosity as a function of shear rate that reduces to Eq. 2 for frontal velocities greater than about 2 ft/D. The fluid characteristics used in the present study are similar to those reported by Gogarty. Christopher and Middleman2 performed experiments with power-law fluids flowing through pipes packed with glass beads. They used a modified Blake-Koteny

Jan 1, 1970

By D. A. Dukelow, G. Derge

THE Fe0-Mn0-Si0, system has many properties of fundamental interest besides its occurrence in steel-making. The system is the simplest ternary complication of the FeO-SiO, binary whose electrochemical properties have been explored. Therefore, knowledge of the conformance of Fe0-MnO-SiO, melts to Faraday&apos;s laws, as investigated by current efficiency measurements, would be of particular value in interpreting the observed variations of electrical conductivity, while at the same time furthering understanding of this type of molten oxides. Pertinent to the present study are conductivity data of FeO-SiO, and Fe0-Mn0-SiO2, and current efficiency data of FeO-SiO,. Concerning conductivity measurements, Inouye, Tomlinson, and chipman&apos; studied the specific conductivity, a, of molten wüstite as a function of temperature and oxide addition. Liquid FeO in equilibrium with an iron crucible was found to have a o whose magnitude and positive temperature coefficient were undeniably semiconductor in nature (o1400°C = 269 ohm-1cm-&apos;). Additions at 1400°C of 5 mole pct MnO decreased o to 227 while a similar addition of SiO2, dropped o to 125. Additional SiO2 produced an exponential decline of o. It was reasoned that because wüstite is known to be oxygen excess and since there is no pronounced change in oFeO upon melting, that UFeO(L)is p-type semiconduction. Björling2 gives o data for the ternary FeO-MnO-SiO, using fayalite, 2 FeO-SiO,, as the base substance. Upon addition of tephroite, 2 MnO-SiO, he noted a small decrease in o. Taking his data for 1400°C with one-half of the fayalite replaced by tephroite, o shows a decrease of some 40 pct relative to o for fayalite, i.e., 5 ohm-&apos; cm-&apos; to 3. In line with this observation, Mori and Matsushita3 reported that substituting MnO for FeO in the silicate de- creased o slightly except at high SiO, contents where the decrease was somewhat larger. Investigating the ionic nature of FeO-SiO2 melts, Simnad, Derge, and George4, found the anode current efficiency, C,, as calculated from iron anode weight loss, was temperature invariant and in general increased with SiO2 concentration. The authors suggested the possible presence of electronic conduction to explain why C+ < 100 pct. Fig. 4 includes their results as curve (b). EXPERIMENTAL METHOD Apparatus—Fig. 1 is a schematic section of the electrolysis cell used in all the current efficiency runs. The melt was contained in an iron crucible that rested on an alundum ring. A centered silica tube came within 1 in. of the surface of the melt and initially served as a thermocouple well and then as the guide for the anode.

Jan 1, 1961

By R. A. Stauffer

THE chief ore of lithium is spodumene, a lithium-aluminum silicate containing up to 3 pct lithium. The preparation of lithium salts from spodumene is costly because of the low concentration of the metal and the difficulty of separating it from the other alkali metals present. Dr. Kroll&apos;s and Dr. Schlecten&apos;s recent paper&apos; has reviewed various methods proposed for preparation of lithium. It will be seen from this paper that the methods proposed to date have required one or another of the lithium salts as a raw material. The high cost of these salts has been the chief item of expense in the lithium metal produced. This situation has made it interesting to investigate the possibility of producing the metal directly from spodumene. When spodumene is calcined at 1000°C in the presence of lime, lithium oxide is replaced in the ore as is evidenced by the fact that it may be leached from the reaction mixture with water.2 Free energy calculations suggested that lithium oxide might be reduced with aluminum or silicon and the lithium produced distilled from the reaction mixture by heating to about 1000°C in a vacuum. These facts taken together suggested that it might be possible to prepare lithium metal directly from spodumene by heating a mixture of the ore, lime, and a suitable reducing agent in vacuum and distilling off the lithium metal as formed. THE REPLACEMENT OF Li20 IN SPODUMENE A series of experiments were undertaken to determine the ratio of lime to spodumene necessary to free substantially all the lithium oxide present in the ore. The spodumene used in these experiments was supplied by Foote Mineral Co. in the form of powder of about 200 mesh. Analysis of the spodumene was as follows: [ ] Lime (cp -200 mesh) was added in various ratios to spodumene and thoroughly mixed in a ball mill. Two hundred gram samples of spodumene-lime mixtures were charged loosely in fireclay crucibles and held at 1000°C in a gas-fired furnace for 5 hrs. The product in each case was ground to pass 140 mesh and then placed in a thimble in a soxhlet extractor. Extraction with water was carried on for 6 hrs. After this period the extract was reduced in volume by evaporation in order to precipitate dissolved lime and was then filtered and titrated with 1/4 normal hydrochloric acid. After correcting for residual calcium oxide in solution, the alkali present was calculated as lithium oxide. The results of these experiments are shown in Table I and Fig I. At lime-spodumene ratios less than 1.5, the products were invariably fused. At the ratio of 1.5 and above, the product was loosely sintered with little evidence of fusion. When the ratio of lime to spodumene was three, replacement of alkali oxides in the

Jan 1, 1947

By R. J. Walter, W. T. Chandler

The Ch-H phase diagram was determined for by-drogen concentrations up to ChHo.9 at temperatures below 400°P&apos;. The phase diagram includes a mis-cibility gap and a eutectoid transformation. A peri-tectoid transformation is postulated at the hydrogen-rich end of the diagram, Phase diagrams were determined for two levels oj purity, of the columbium. A single solid solution exists in the Cb-H system above 400°F. There has been considcrable disagreement among investigators concerning the system at temperatures below 400°F. Albrecht, Goode, and ~allett&apos; proposed a miscibility gap containing two bcc phases with the two lattice parameters converging at about 140°C (285-F), and Brauer and ~erman&apos; found a two-phase room-temperature region between 10 and 41 at. pct H. At sufficiently high hydrogen concentrations in the one-phase region, the hydrogen-rich phase was found to be face-centered orthorhombic. Wainwright, Cook, and Hopkills3 recently reported that the face centered orthorhombic hydride phase is derived from a unit cell which is slightly tetragonal with a small departure from 90 deg of the angle (y) opposite the r axis. The orthorhombic hydride phase was observed for hydrogen concentrations between 0.2 and 0.8 H/Cb atom ratio. Paxton and coworkers4 found that needlelike hydride plates formed in a hydrogen-charged columbium single crystal and suggested that this transformation possessed the characteristics of a diffusionless phase transformation. On the basis of room-temperature, X-ray diffraction data, komjathy&apos; suggested that an order-disorder or martensitic transformation occurs. In the present study, the Cb-H system was investigated to resolve the discrepancies found in the literature for this system. PROCEDURE The columbium specimens were prepared from two heats of wrought 1/2-in.-diameter electron-beam melted columbium rod and from two columbium powders of -80 mesh size of different impurity contents. The columbium bar stock was pur chased from Urah Chmg Corp.; the 99 and 99.5 pct purity colulnbium powders were obtained from Fansteel Metallurgical Corp. and Kern Chemical Co.. respectively. The chemical analyses of the columbium bar and powders are listed in Table I. Hydrogen charging was performed by exposing the columbium specimens to hydrogen at 1 atm pressure at various temperatures. After exposure the specimens were quenched to prevent the hydrogen pickup which would take place if cooled in hydrogen, or the hydrogen loss that would occur if cooled in an inert gas. Adequate hydrogen purity was achieved by passing high-purity tank hydrogen (maximum 5 ppm total impurities) through an Engelhard catalytic Deoxo unit, magnesium per chlorate desiccant, and finally through activated charcoal at the temperature of boiling nitrogen. Activated charcoal at -321°F has been reported6 to remove impurities from hydrogen to a nondetectable level. A schematic representation of the heat-treating apparatus is shown in Fig. 1. A metal-sheathed thermocouple embedded in the colun~bium specimen was used to control the temperature during heat treatment and to pull the specimen boat into

Jan 1, 1965

By R. S. Silo

A new process for leaching oxidized copper ore (CuO) is presented. Its principle advantage is that it requires low cost raw materials. For large operations the only materials used are sodium chloride (NaCl) and calcium carbonate (CaCO3). In those operations of medium size, sulfur, which is abundant in the North of Chile, is used. However the process may also be applied to small copper plants provided low cost sulfuric acid is available as a substitute for sulfur. That is, it may be applied to those small capacity plants where large additional installations for the regeneration of the leaching solution are not needed. The method is comprised of six stages, namely: Crushing, Leaching, Washing of the Solution, Precipitation, Regeneration of the Leaching Solution, and Fusion. A flow diagram for this process in a large or medium-sized plant is given. LEACHING This process requires hydrochloric acid as the leaching solution for treating copper ores. This is easily produced from sulfuric acid and sodium chloride as follows: A small excess of NaCl is advisable to avoid the presence of free sulfuric acid. The experiments reported here were performed with 36 grams of HC1 per liter of solution to obtain a free acidity equivalent to 50 gpl of H2SO4 (the usual leaching solution concentration). Hydrochloric acid leaching may be done by either of the usual methods; i.e. percolation or agitation. The method selected depends on the characteristics of the ore. No matter which method is chosen, low pressure air can be used either as an air lift for circulation of the solution, or for agitation of the pulp with "Pachuca" tanks. In either case, there are no problems with respect to oxidation. Leaching by agitation produces good recovery; but at times, the problem of high consumption of leaching solution or the overproduction of grinding slimes which interfere with contact between phases negates this advantage. The percolation method was used in this study. Percolation took place in four 15-liter containers, 11 1/2 in. diam. by 12 in. height, having hemispheric bottoms. Each container was fitted with a wooden bottom having 1/4 in- holes. The air lift was a 3/4 in. plastic tube 10 in. high. Air at 6 psi was supplied from a rotating laboratory compressor. 10 kg of ore were charged to the container and counter-current leaching was used. The leaching solutions were fed through the center pipe in order to use the ascending solutions to reject the air in the charge. The solution circulated through the air lift in order to facilitate the movement according to the increase in density produced by the reaction between the phases present. Specific observations made in this report cannot be generalized because the leaching characteristics are dependent on the nature of the ore used, the method of leaching, and the production of primary or secondary slimes while crushing or leaching.

Jan 1, 1967

By E. T. Turkdogan

The activity of sulfur was determined as a function of composition of ferrous sulfide by equilibrating with hydrogen sulfide-hydrogen gas mixtures at 670° , 800°, and 900". The present results supplement the available data over the composition range from 36.6 to 39.5 pct S. The X-ray lattice spacing measurements made are in accord with the available data and indicate that the limiting composition FeSl.008 may be taken for the iron-iron sulfide equilibrium. The growth rate of ferrous sulfide on iron was measured by reacting iron strips or blocks in hydrogen sulfide-hydrogen gas mixtures. Owing to the slow approach to equilibrium between the gas phase and the surface of the sulfide layer, The sulfidation experiments were carried out for several days. It is shown that the growth rate ullimately proceeds in accordance wilh the parabolic rate law. From the parabolic rate constants and the thermodynamic data on iron sulfide the self-difiusivity and chemical diffusivity of iron in ferrous bisulfide are evalualed. The self-diffusivity of iron thus derived zs found to increase with increasing sulfur content. THE ferrous sulfide known as "pyrrhotite" is a non-stoichiometric phase having a wide composition range from about 50 to about 58 or 60 at. pct, depending on the sulfur activity. RosenQvistl studied the thermodynamics of this phase over wide ranges of temperature and composition. Hauffe and Rahmel&apos; and Meussner and ~irchenall~ studied the parabolic rate of sulfidation of iron in sulfur vapor. By using markers, these investigators showed that the iron cations were the predominant diffusing species in iron sulfide. This is confirmed decisively by the self-diffusivity measurements of condit4 who showed that the self-diffusivity of sulfur in ferrous sulfide is several orders of magnitude lower than the self-diffusivity of iron. Although much has been learned from these studies about the Fe-S system, further research on this subject was considered desirable for better understanding of the physical chemistry of iron sulfide. This work was confined to the study of the kinetics of sulfidation of iron in hydrogen sulfide-hydrogen gas mixtures. The results of this study are given in two consecutive parts. Part I, the present paper, is on the parabolic rate of sulfidation of iron and the diffusivity of iron in ferrous sulfide. The second paper, Part 11, is on the kinetics of the surface reaction between hydrogen sulfide and ferrous sulfide. EXPERIMENTAL Three types of experiments were carried out: i) equilibration of ferrous sulfide with gas of known E. T. TURKDOGAN, member AIME, is Manager,Chemical Metallurgy Division, Edgar C. Bain Laboratory for Fundamental Research, U. S. Steel Corp., Research Center, Monroeville, Pa. Manuscript submitted March 6. 1968. ISD sulfur potential; ii) X-ray studies of ferrous sulfide; and iii) measurements of the parabolic rate of sulfidation of iron. Equilibrium Studies. About 1 g of iron powder or foil. contained in a small recrystallized alumina crucible ind suspended from a calibrated silica spring, was reacted with a hydrogen sulfide-hydrogen mixture of known ratio until no further change in weight was observed. %hen the gas composition was changed and the new state of equilibrium was established after several hours of reaction time. The composition of the sulfide was obtained from the initial weight of the sample and the weight after equilibration. X-Ray Studies. The lattice parameters of some of the equilibrated samples were determined using the General Electric XRD-5 diffractometer with a cobalt tube (no filter) set at 40 kv apd 10 ma; the CoK, radiation was taken as 1.79020A. Observed 220 and 311 diffraction peaks of silicon served as an internal comparison standard to correct for possible misalignment of the goniometer. The lattice parameters of the sulfide phase were calculated from the corrected Bragg angles of the 110 and 102 peaks. Rate Studies. In the initial experiments attempts were made to measure the parabolic rate of sulfidation by measuring the gain in weight of a thin iron strip, -0.05 cm thick, suspended from a silica spring in the reacting atmosphere. The preliminary experiments showed that this technique was not reliable for the measurement of the parabolic growth rate of the iron sulfide layer. In the subsequent experiments the data on growth rate were obtained by measuring, on a microscope stage, change in the thickness of the sample after reaction for a specified time in a hydrogen sulfide-hydrogen mixture of known sulfur activity. For each reaction time a new sample was used. Precision-machined iron blocks, 0.5 by 2 by 5 cu cm, were de-greased and annealed in hydrogen for several hours prior to the sulfidation rate measurements. The experiments were carried out at 670°, 800°, and 900°C in gas mixtures having the ratios, and 1.0 for periods of times from a few hours up to 8 days. Apparatus and Materials. A vertical globar tube furnace with a 3-in.-long uniform temperature zone was used. The glass tube fittings were fused on the zircon reaction tube, 1.5 in. diam. The temperature was measured with a Pt-10 pct Rh/Pt thermocouple placed in the hot zone of the furnace inside the reaction tube (an alumina thermocouple sheath was used). A separate thermocouple was used for the temperature controller which maintained the furnace temperature constant within about 2°C. Anhydrous liquid hydrogen sulfide and oxygen-free dry hydrogen from gas tanks were used in preparing the gas mixtures by the constant head capillary flow-meters. In all cases volume flow rate was 1000 cu cm per min at stp, corresponding to a linear velocity of about 6 cm per sec at 800°C; under these conditions

Jan 1, 1969

By P. G. Shewmon, H. E. Collins

We have studied the effect of adsorbed sulfur on the surface self-diffusion of copper using eight diflerent surface orientations and the grain boundary grooving method. The eight orientations studied were the four lying near the low-index surfaces—(loo), (Ill), and two directions in the (110)-plus four higher-index surfaces. Surface-diffusion measurements were made over a range of HZS concentrations (in Hz) from 3 to 1500 ppm between 830°and 1050°C. The results can be divided into two groups—Group 1 contains the two (110) surfaces while Group 2 contains the remaining six surfaces. In Group 1, increasing the temperature increases the effect of Hz S on DS for the Hz S range 5700 ppvn. Qs and Do increase with increasing H2S concentration in this Hz S range. Beyond this range, increasing the temperature decreases this effect on D,; also Q, and Do decrease. In Group 2, increasing the telnperature decreases the effect of H2 S on D, for the H2S range studied, and Qs and Do decrease with increasing Hz S concentration. In any study of surface phenomena, there invariably arises the question of the possible presence of and effect of adsorbed impurities. Such questions are well-founded since the presence of adsorbed atoms can sometimes produce marked changes in the kinetics of surface-energy-driven processes. In the last few years, values of the surface self-diffusion coefficient, D,, have been determined on a variety of metals by studying the decay of scratches or the growth of grain boundary grooves.L~3-L0~L3 Yet there has been relatively little work done in which the concentration of an adsorbed impurity was systematically varied and the effects observed. Work of this sort would provide some basis in fact for the assertions often made about the ro1.e of adsorbed impurities in the differences between the results of different workers in different atmospheres and on different metals. It also is relevant to those cases in which surface monolayers produce profound effects in commercially important processes. The most marked example of such effects is the ability of nickel or palladium to increase the sintering rate of tungsten by many orders of magnitude.&apos; The aim of this work was to study the effect of sulfur partial pressures on the surface self-diffusion of copper. It was felt that this in conjunction with a study of the degree of adsorption and type of active sites involvedL8 would provide a wide range of data for one system and hopefully lead to some insight into the mechanism by which sulfur adsorption influences copper diffusion. The main reasons for choosing the Cu-S system were, first, faceting was reported not to accompany the adsorption of sulfur. This is required if our experimental technique is to work. Second, Oudar has determined a high temperature adsorption isotherm for this system, an event which puts the Cu-S system almost in a class by itself.I4 EXPERIMENTAL PROCEDURE Initially, we considered studying the effect of an adsorbed impurity on surface self-diffusion of copper using isolated (or single) scratch smoothing as the technique and oxygen as the impurity. Copper was chosen as the material because the effects of orientation and anisotropy of the surface self-diffusion coefficient, D,, of copper in a dry hydrogen atmosphere had been studied extensively by Gjostein&apos; and by Shewmon and ~hoi.~,~ The isolated scratch technique was chosen because both the effects of surface orientation and anisotropy of D, in a given surface could be easily studied with this method.~ Oxygen was tried as the impurity because Robertson and Shewmon""~ had studied its adsorption on copper at 1000°C over the range of oxygen partial pressures of 10"22 to 10-l3 atm. After several preliminary runs, it became evident that neither the scratch technique nor the impurity oxygen would be satisfactory for this work. Scratching deforms an annealed surface so that the region near the scratches recrystallizes, thereby disrupting the scratch profiles. One can avoid this by deforming the specimen sufficiently before scratching to give complete recrystallization on subsequent heating.4 However, as a result of Gjostein&apos;s success in scratching and annealing undeformed gold single crystals without local recrystallization,13 we attempted something similar with copper single crystals using a 0.7-mil diamond phonograph needle mounted in a Tukon hardness tester. All specimens recrystallized upon being annealed. Also, some copper specimens were sent to Gjostein to be scratched using his technique. The results were the same. As a result, the scratch technique was dropped in favor of the grooving of symmetric grain boundaries. Preliminary work using oxygen showed that faceting began to occur before oxygen adsorption had any measurable effect on D, at 938°C (at Pbo/P, = 0.12). Since heavy faceting would interfere with the measurement, we decided to use a sulfur-containing atmosphere (H2S/H2). Work by Oudar and Benard&apos; and Robertson" showed that sulfur absorbed on copper and that faceting was not observed.

Jan 1, 1967

(The following list contains the names of those members of the Institute of whose connection with military service we have only recently become acquainted; it also includes the names of a few who have recently been promoted or transferred, indicated by a *. A complete list was published in the Year Book, issued as a supplement of the Bulletin for March, 1918.) *AMBLER, HARRY A., 1st Lieutenant, 0. R. C., 30th Infantry, A. E. F. BAKER, R. F., Private, Intelligence Section, Headquarters 90th Division. *BARTON, L. A., Captain, 604th Engineers. *BATTEN, H. L., Lieutenant, Canadian Engineers, C. E. F. *BENSEL, J. A., Major, U. S. Reserves. BIRKETT, HOWARD, Lieutenant, Aviation, U. S. Signal Corps. BLOOMFIELD, E. C., Lieutenant, 1st Canadian Tunnelling Co. BOOTH, L. E., Watertown Arsenal, Det. E. 0. C., N. A., Watertown, Mass. *BOWMAN, REGINALD G., 1st Lieutenant, Engineers, U. S. R., Int. Ord. Dept. No. 4, A. E. F. *BRADLEY, CLARENCE I., Convois Automobile Section 585,. S. S. U., P. A. R., B. C. M.

Jan 7, 1918

By J. A. Ede

THE object of the writer is to call attention to a rather unique aggregation of economic products distributed over a line of succeeding formations about 3 mi. long, to be seen within a few miles of La Salle, Ill. Fig. 1 is an ideal section of the stratification exposed and exploited along a distance of 3 1/5 mi. in a southwesterly direction from the quarry of the Utica Hydraulic Cement Co. located near the historic site of Kaskaskia village to the Oglesby, shaft at Oglesby. No attempt has been made to cover the whole field, special mention only being made (with the exception of two places) of the operations found along the course or parallel to the direction assumed in the ideal section. I have used Fig. 2, after J. H. Bent and De Witt Kelly, to locate the relation of the La Salle anticline to the coal mines of this district and to show the operation of No. 1 and 3 mines of the Illinois Zinc Co.

Jan 9, 1919

By Charles E. Heinrichs

There arc still ample reserves of phosphate in Florida and Tennessee, but the richest low-cost areas have been exhausted. The miners, by the introduction of more efficient equipment, have succeeded in preventing material increases in production costs. Further mechanical improvements could not be expected to keep up with the factors tending to increase costs. While the conventional phosphate "washers" are capable of recovering practically all of the plus 1.5-mm. phosphate from the matrix, approximately 50 per cent of the phosphate values are in the minus 1.5-mm. sizes. Flotation now affords an economical and efficient means for recovering the fine ( — 1.5 mm.) phosphate formerly discarded to waste dumps. Through the reclamation of dumps and recovery from current washer wastes, flotation has doubled the reserves of Florida and Tennessee. By doubling recoveries from the matrix, flotation reduces capital investment requirement and substantially reduces production costs. It definitely improves the grade of the total production and provides a flexibility of operation that cannot be obtained by any other known means.

Jan 1, 1934

By Newell Alford

FORECASTS of future timber consumption in soft-coal mining are handicapped by; the lack of adequate experience records for estimating properly the timber requirements of the industry. Data were obtained from plants where records are kept or from operators who collected the information and to these were added FIG. 1.-GROWTH OF POPULATION IN UNITED STATES, FROM PEARL&apos;S ?BIOLOGY OF DEATH." composite figures for the continental United States in 1905 and 1919 1 and for central and. Western Pennsylvania and for Illinois in 1922.2 The result, representing slightly over 928;000,000 net tons, is shown in Table 1. Some of the companies furnishing data were unable to segregate the timber into classes of use but for those who did, Table 2 shows the board feet of posts and cross bars used per ton of coal mined and the, percentage of the total timber consumed that was used in roof support. The wide variation in amounts of timber per ton of coal mined is the result of

Jan 5, 1924

By Walter Kauenhowen

The crude-oil production of Germany without Austria during 1938 amounted to 3,864,518 bbl., representing an increase of 21.7 per cent over the 3,173,373 bbl. produced in 1937. Adding the Austrian production, the crude-oil production of the new German Reich totaled 4,259,717 bbl. during 1938, representing an increase of 25.3 per cent compared with the respective figures of the previous year. According to published official data, and using a conversion factor of 1 metric ton equaling 7 bbl., the oil production of Germany in 1938 was as shown in Table 1. A semiofficial publication1 states that the program of the crude-oil industry for the second year (1938) of the four-year plan was successfully accomplished. According to the same source, new drilling developments at the following localities were promising: Reitbrook near Hamburg, Heide in Holstein, Eicklingen-Sandlingen near Celle, Steimbke near Nienburg, Worms in the Rhine Valley, Gifhorn near Braunschweig, Mölme near Oberg, and at other places. The drilling activity for oil is illustrated by the figures in Table 2.

Jan 1, 1939

By Walter Kauenhowen

The crude-oil production of Germany without Austria during 1938 amounted to 3,864,518 bbl., representing an increase of 21.7 per cent over the 3,173,373 bbl. produced in 1937. Adding the Austrian production, the crude-oil production of the new German Reich totaled 4,259,717 bbl. during 1938, representing an increase of 25.3 per cent compared with the respective figures of the previous year. According to published official data, and using a conversion factor of 1 metric ton equaling 7 bbl., the oil production of Germany in 1938 was as shown in Table 1. A semiofficial publication1 states that the program of the crude-oil industry for the second year (1938) of the four-year plan was successfully accomplished. According to the same source, new drilling developments at the following localities were promising: Reitbrook near Hamburg, Heide in Holstein, Eicklingen-Sandlingen near Celle, Steimbke near Nienburg, Worms in the Rhine Valley, Gifhorn near Braunschweig, Mölme near Oberg, and at other places. The drilling activity for oil is illustrated by the figures in Table 2.

Jan 1, 1939