Search Documents

By Jon G. Bredeson

The electromagnetic noise that exists in a mining environment is quite severe and was shown to have been reasonably well documented by a number of researchers in the Phase I Report. The noise levels are such that prudent communication design requires the careful use of all the electromagnetic noise data available. A comprehensive survey was undertaken to determine techniques used in various industrial environments to achieve secure communications in the presence of electromagnetic interference. The techniques were given in the Phase I Report and are rudimentary, but have produced reasonably good results. A number of these techniques could be applied to the mining environment.

Jan 1, 1980

By H. P. Greenwald

[For sarno years past the Safety in Minbr. Resaarch J30ard of Great Bri tr-dn ha:1 been making ar.. intensive Gearch for, traterials that \.'ould be 1!\ore ef-ficient than rock dust and th t 'could l1eplace it Jholly or in El:}rt as a muans of prevEll'ltine the propa 'tion' of 'c63.1~dust exnlosions in. mines21 In the course of this \o.'ork several rock c.ur--ts md numerous inorganic compounds I,/ere tested. The result w place incombus.ti ble substFlnces in two main groups~ (1) r.:ho se who sa effect' in suppre aeina Jlihe cor.lbustion of coal dUDt i 0 pro-]

Jan 1, 1940

By F. Peer

This Technical Note was presented as a poster at the Western Cape Mineral Processing Symposium held in August 2001 The cleaning of fine coal (-1000 µm) in today?s coal preparation plants is an economically important factor. Coals with high ash contents are, in general, commercially undesirable. Current well-known techniques for treating fine coal include froth flotation and spirals. The primary critical factor with regards to spirals is the efficiency of the process whereas that of flotation, is the cost of there agents used. Research into enhanced gravity separation techniques has resulted in several commercially available enhanced gravity separators. This project was based on a preliminary investigation into the feasibility of one such separator, to effectively treat fine (-500 µm) coal. Experimental variables included particle size and speed of rotation of the said instrument. The performance of the separator was compared to the results obtained from liquid density separations done for the two coal fractions evaluated. From the results obtained in this preliminary study it appears that the piece of equipment investigated does not measure up to expectations. Recommendations for further investigation include the evaluation of the instrument on other South African coals to obtain conclusive results.

Jan 1, 2002

By W. F. Visser

The growing availability of information and data analysis capabilities of recent years provides new opportunities for improving the performance of mining operations. By using real-time measurements and artificial intelligence, it is possible to respond faster to changing conditions, while accurate and timely information permits rapid evaluation of changes and fast business improvement decisions. This article presents a blueprint for alignment of systems, organizational design, and management practices to leverage these developments in performance-driven operations management in mining and mineral processing. The first component of the blueprint is a performance framework with a system of key performance indicators for production control that can be used across organizational levels. This system places improvement at the core of management activities, giving greater importance to improvement skills at lower organizational levels, so companies can leverage available information for improving operational control. Secondly, the blueprint defines an organizational structure that strengthens performance improvement with technological and change management capabilities. Finally, the blueprint proposes alignment of management practices, covering the optimization of short-interval controls, the application of an improvement project portfolio management system that determines the ownership of improvement projects, and the coordination of controls across the organization. This combination of systems, organizational design, and management alignment supports rapid decision-making at the right organizational level. Introduction of the presented blueprint for operations management enables mines to leverage the developments in information and analysis capabilities to improve the performance of operations.

By G. W. LAAiIBOURNE

FEW mines possess a history of more fascinating interest than the Ontario at Park City, Utah. The famous Bonanza's production record of over $50,000,000; the great extent of its workings; the remarkable character of its mineralization; the fact that recent discoveries have shattered preconceived theories of the geology of the camp practically assuring the half-century old property a future as active and as prosperous as the past make the Ontario one of the unique mines of the world. A mere accounting of the wealth created by this historic property not only exemplifies the great profits

Jan 1, 1925

By Mandius C. Lundal

This report describes the work done to develop a coal mining machine to increase productivity and recovery from thin seams beyond the highwall, in addition to decreasing the miner's susceptibility to to highwall hazards. First, radar transducers were adapted to measure coal thinkness and detect rock and coal interfaces; Then, the radar was incorporated into a cutterhead with steering controls. Next, visual displays were designed to show cutter position in the coal seam, and anticipated change In coal seam inclination. Finally, development of a telemetry system made remote control of the cutterhead possible. Simultaneously, a high-performance extended depth (HPxD) auger machine was designed with an automatic system to handle 600 ft of 36-in. diameter dual spiral flight conveyor sections. A two man crew controls all operations from a weather conditioned cab outside the VDZ, either at night or day time. As a primary mining tool, working 4000 hr/yr (2 shifts/day) recovering 60% of the coal 600 ft beyond the highwall, production to 500,000 ton/yr can be achieved. Volume II contains technical discussion of subsystems and machine drawings.

Jan 1, 1977

By Alfred V. C. Meyer

A Blastcorder4 was calibrated on the Bureau of Mines shaking table in the frequency range of 12 to 40 c.p.s. and in the amplitude range' of 0.25 to 1.0 g. The results of this calibration study show that in the frequency range of 12 to 30 c.p.s. the average accuracy of the Blastcorder is approximately ± 0.1 g.

Jan 1, 1962

Discussion following the presentation at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 8th April 1916, included the author's introduction, written contributions by Bedson P.P., Gregory T.W.D. and Morgan J.D., oral contributions by Louis H., Greener T.Y. and Severs W., and the author's reply

Dec 1, 1916

By F. E. Spencer

Calculated equilibrium data are presented for three phases in the flue gas stream from a hypothetical open cycle MHD generator. A typical coal is "burned" with 1.0 gram-mole K2O seed per kilogram coal and with 101 percent of stoichiometric air. Tables of composition and the overt thermodynamic properties, enthalpy and entropy, are given for the temperatures 2200 (-100) 1100 kelvins, pressures 1.0 and 1.5 atmospheres, and slag rejection figures of 90 and 75 percent.

Jan 1, 1973

By Nikolaos Polysos, Holger Witthaus

INTRODUCTION The classification system for German coal mining is the result of approximately 100 years of experience in roadway development and longwall mining. It is also based on different research projects covered by national and European research programs. Over the past 30 years, more then 600,000 m of road-ways have been driven and employed for mining activities. To properly describe the German rock mass classification system, therefore, it is useful to take a look at the main geomechanical preferences and common support systems. The decision about the most effective development technique and support system is based on a synthesis of rock mass classification and geomechanical analysis. The properties of surrounding rock, the in situ stress, and the influence of mining activities in several seams at each German mine must be considered for the evaluation of the expected deformation of the roadway. The mine layout, the requirements of ventilation and fire prevention, as well as the need to maintain emergency escape routes for the miners, require that the gate roads remain usable after the passage of the longwall face in most cases. Moreover, the gate roads must be maintained despite the high stresses that are applied during longwall retreat mining. Therefore, gate road design must address a broad spectrum of potential deformation environments. In the past, when gate roads were supported solely with yielding steel arches, lithologic descriptions of the surrounding strata conditions were adequate for the dimensioning of support and the prediction of the roadway deformation. The current conditions of multiple-seam mining at depths of up to 1,700 m require combined support systems, including pattern bolting and backfilled steel arches. Rock bolt support is used for development, after which (typically 50–100 m outby the face) the steel arches are installed and backfilled with building material (concrete) in order to achieve an optimized development rate. The rock mass classification system described below was developed especially for the conditions of German hard-coal mining. It includes the stress distribution caused by multiseam workings (including crossing goaf edges of former longwalls), as well as in situ stresses due to greatdepth and the presence of tectonic faults. It is based on the evaluation of four parameters: • Geotechnical analysis of drill cores • Geotechnical observation of the development face • Geotechnical classification of tectonic structures (faults) • Standard classification derived from geotechnical assessment and evaluation of stress conditions (using numerical modeling for stress calculation) ROCK STRENGTH One of the most important input parameters for describing strata conditions is the strength of the rock. The German classification system is based on a description of lithotypes. This method has been used successfully since the 1950s and is based mainly on the uniaxial compressive strength (UCS) of the material. An evaluation of the rock strength observed in a survey of approximately 82,500 samples of rock core yielded the results shown in Figure 1. The three most common coal measure rock types are mudstone, siltstone, and sandstone. Each shows a specific mean UCS level and a different spread between the minimum and maximum values. Sandstones, in particular, have a wide spectrum of compressive strength, ranging from approximately 40 MPa to greater than 130 MPa, with an average of 85 MPa. The causes of this wide range include different sedimento-logical preconditions, facies, and digenetic processes. [ ]

Jan 5, 2007

By O. Schumacher

Guidelines for publication of information defining the amount and grade of resource material available in a deposit are well established in Australasia?s JORC Guidelines, Canada?s National Instrument 43-101 and similar documents in South Africa, Peru, Chile and elsewhere (Table 1). These guidelines provide standards to apply regarding the geologic and geostatistical basis for describing the level of confidence to be assumed for an estimate of the amount and grade of material. All of them provide for a strict distinction between material that has been demonstrated to be economically mineable and that which has not, and all of them provide terms such as ?resource? or ?exploration information? to be applied to data regarding material that has not been demonstrated to be economically mineable. It is not until an economic study has been completed that we are allowed to apply the powerful terms ?reserves? and ?ore? to our deposit material. Indeed, the application of these eye-catching labels immediately tells the reader that an economic study has been completed by a qualified person, and that the results of the study were positive. While extensive guidelines are established for describing the level of confidence in published geologic data, and the nature of the economic study that should be accomplished before using the terms ?reserves? or ?ore?, surprisingly little guidance is provided regarding the process to use, and the level of detail to attain, for estimating capital and operating costs for the study. The intent of this paper is to lay the groundwork for development of suitable guidelines for the cost estimating process. While the codes do not provide specific instructions for the cost estimate, they do provide numerous hints and clues to help determine the level of detail expected and the type of procedure to apply in preparing the estimate. This paper will first review the various codes to gain an insight into the thinking of the drafters of the codes regarding their unstated expectations for the cost estimating process. Based on this review, a series of guidelines are proposed for this purpose.

Feb 27, 2013

By Thomas Donnelly

Introduction THE Province of San Cristobal is situated on the south side of the island of Santo Domingo about 25 miles west of Santo Domingo city, the capital of the republic. The copper mineralization is found about 1.-CAMP BUCARO. THE TOP OF THE RIDGE IN THE BACKGROUND MARKS THE CONTACT OF THE LIMESTONE AND TUFFS. S miles north of the town of San Cristobal, in the section known as Bucaro Hill; in San Francisco Hill; on the Nigua River; and on the Jaina (Liver. The district is reached by automobile from Santo Domingo city over an excellent road for 25 miles to San Cristobal, and then, by horse-back 6 or 8 miles up the Nigua River to what is locally known as "Camp

Jan 8, 1915

By K. E. Stanfield

[Asphalt ~~d road oil ar8 the principal products manufactured from Wyor.1in~ Ilblack oilo" \r,hich, beca.use of th?lir hig.~ E\.sphal t and hig} sulfur COi.1Jce~1t, .!?re difficult e':ld costly to refine into hi?;h-gra.de motor f 101s, burning oils. and lucri ants by presont mothods. Accordin~ly. the demand for truHle asphaltic renidl urn for the construction of roade aJ1.d other uses is 3. controlling factor in the quantity of crud~ oil prod ICed. The increasiilg -u.tilization of special aST>ha.lts as ine}""Pensive bonding, in-]

Jan 1, 1941

By Pierre Pelletier, Christian Pichetie, Dany Pelletier

"IntroductionDuring 1994, Barrick Gold Corporation, or American Barrick at that period, acquired Lac Minerals Ltd. properties. One of them was the Bousquet Complex. The Bousquet Complex is divided into three distinct sites: one mine (Bousquet 2), one mill (Est-Malartic Division) and one analytical chemistry laboratory (Les Terrains auriferes).The Bousquet 2 orebody was discovered in 1986. An extensive drilling program was initiated during 1987. Its purpose was to define the orebody extent. At the end of 1997, gold production from Bousquet 2 mine reached 1 290 000 oz of gold from a cumulative tonnage processed of 4 175 000 M t.From 1980 to 1990, the Est-Malartic mill was used for the treatment of ore from the following mines: Bousquet 1, Doyon, Francoeur (Richmont mines), Buckshot and 1-20 stope. At present, the mill receives ore from the Bousquet 2 mine.HistoryThe Est-Malartic mill is located close to the town of Malartic in northwestern Quebec. The mill has been in production since the mid-1930s processing mainly clean, free mill gold ore. Active mining from the Est-Malartic mine ceased in 1979 and the mill was switched to custom processing of ore from La Mine Doyon located some 45 km to the west. This custom processing arrangement continued until 1987 when the expanded mill at Doyon became available to process all of the Doyon production. In 1987, Lac Minerals commenced development of a second mine at the Bousquet site located 40 km west of Malartic. This mine, Bousquet 2, is the down dip extension of the La Ronde mine developed by Agnico Eagle. During pre-feasibility evaluations, it was determined that it would be economically more attractive to modify the existing Est-Malartic mill than building a new facility on site. The Est-Malartic mill modifications for processing the high-copper/gold ore from the Bousquet 2 mine began in late 1989 and new circuits were commissioned in mid-1990. Modifications included the addition of both gravity and flotation concentration circuits to recover coarse, free gold and the copper. The existing leaching circuit continued to operate on the copper flotation tailings with some minor modifications to the solution handling systems. A S02/Air cyanide destruction circuit was also added at that time."

Jan 1, 2000

[Murray and Renard: chondres on ocean floor, XLI, [155]. Musconetcong Iron Works, Stanhope, N. J., blnst furnace, XL, 467. MUSSEN, H. W.: Discussion on The Bogoslovsk Mining Estate, XXXIX, 897. death, XLIII, [Ixxvi]. Muzo, CoIombia: emerald deposits, LV, 910. emerald mine, XXXIX, 317. minerals, LV, 925.]

Jan 1, 1918

Book review Proceedings of the Symposium on Mining Methods. London, Institution of Mining and Metallurgy, 1974. 160 pp. The Symposium was held from 30th October to 1st November, 1974, and the papers include an interesting range of subjects in coal-mining operations, covering the improvements achieved to date, current practice, and required development for the future. Salamon, M.D.G., and Oravecz, K. 1. Rock Mechanics in Coal Mining. 119 pp. NIM reports Report no. 1822 Stability constants and linear free-energy relations for the platimtm-group metals. (22nd Oct., 1976). Report no. 1852 A revised method for the dissolution of platiniferous materials by the sealed-tube technique. (18th Oct., 1976). Report no. 1828 y-picoline adducts of the nickel, copper, and zinc chelates of 2-thenoyltrifluoroacetone. (26th Nov., 1976) Report no. 1847 A pilot-plant investigation of a kinetic model for flotation.(19th Nov., 1976)

Jan 2, 1977

By D Walker, A Tsvetkov, P Voigt, O Kloiber-Deane

The GPM Gold Operation has been employing an Albion Process™ plant at its Sotk (Zod) gold mine in Armenia since 2014. Long term data from the operation is now being published for the first time. The data presented includes concentrate throughput, as feed to the Albion Process™ plant (tonnes per day), sulphur grade in concentrate (% S), total sulphide sulphur oxidation in the Albion Process™ plant (% SOx) and gold recovery from Albion Process™ plant residues (%). The data provides a basis for evaluation of the effectiveness of the commissioning, ramp up and operation of the Albion Process™ plant. Notwithstanding the impact of a slower concentrator commissioning than expected, the plant demonstrates Series 1 behaviour on McNulty ramp up curves, indicating successful commissioning and fast ramp up. Interrogation of the data and operational experience indicates that this successful operation is a result of a process that is flexible, robust and stable, one that was designed well based on solid testwork results and pilot plant trials during the study phase undertaken by Glencore Technology and Core Resources, and where the local operators were provided with appropriate training in operation of the plant. CITATION:Voigt, P, Walker, D, Kloiber-Deane, O and Tsvetkov, A, 2018. Ramp-up and long-term performance of the Albion Process™ plant at GeoProMining Gold Armenia, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 339–350 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By G B. Arehart, J L. Mauk

Quartz veins from the Martha Hill epithermal gold-silver deposit, Waihi, commonly exhibit crustiform banded textures. Visual differences observed between bands are primarily the result of a 1 to 1500 ¦m variation in quartz grain size. Quartz band textures are dominated by anhedral interlocking quartz mosaics, commonly associated with minor adularia and sulphide phases; these textures are interpreted to be products of amorphous silica crystallisation. The occurrence of rhombic adularia suggests that prolonged boiling influenced parent fluids. In contrast, the presence of coarsely crystalline bands, made up of subhedral to euhedral quartz grains, infers primary crystal growth from solution; evidenced by the occurrence of growth-zoned quartz within these bands. There is a narrow range of 3.3ë in d18Oquartz between maximum and minimum isotopic values for the deposit. Significant overlap in d18Oquartz values are observed between the Martha and Welcome lodes. However, statistically significant and commonly systematic differences do occur between individual bands analysed in most samples. Temperature fluctuations may be the dominant factor responsible for observed inter-band variation.

Jan 1, 1995

Due to the reduction in frictional resistance, the characteristics of joint infill have a major role to play on rock mass instability. This paper elucidates the laboratory behaviour of graphite infilled joints based on a large-scale shear apparatus under constant normal stiffness (CNS). Discontinuities in a graphite mine have been simulated using high strength gypsum plaster, with the joints infilled with compressed graphite layers. The Fourier series was employed to characterize the joint surface, and the method of using the Fourier coefficients for the prediction of dilation and normal stress with displacement is explained. Die Charateristik von Verbindungsfüllungen hat einen wichtigen Einfluss auf Felsmassenstabilität aufgrund der Verringerung des Reibwiderstandes. Diese Veröffentlichung untersucht das Verhalten von Graphit gefüllten Verbindungen im Labormaßstab mit einer Methode die auf einem gross-umfang Apparateprinzip unter konstanter Normal-Steifheit beruht. Unregelmässigkeiten in einer Graphit Mine wurden mit Gypsum Gips von hoher Festigkeit simuliert, die Verbindungen wurden mit kompressierten Graphitschichten gefüllt. Fourier Reihen wurden angewandt um die Verbindungs Fläche zu Characterisieren. Die Methode die verwendet wurde um die Ausdehnung und Normalkraft mit der Verschiebung mit Hilfe von Fourierkoeffizienten zu bestimmen wird beschrieben. Due à diminution des résistances par frottements, les caractéristiques des joints de remplissage joue un rôle majeur sur les instabilités de la roche. Cet article étudie le comportement en laboratoire des joints de remplissage en graphite à partir d’un dispositif de friction à grande échelle sous rigidité normale constante. Les discontinuités dans une mine de graphite ont été simulées grâce à un plâtre à haute teneur en gypse, dont les joints ont été remplis de couches de graphite compressées. La caractérisation de la surface des joints a été réalisée avec les séries de Fourier. La méthode utilisant le coefficient de Fourrier pour la prédiction de la dilatation et de la compression en fonction du déplacement est également expliquée.

Jan 1, 2003

By J. L. Potter

An inert-gas fusion technique was applied by the Bureau of Mines to the oxygen analysis of mixed-fluoride electrolytes used in electrowinning uranium and the rare-earth metals. Method development included: (1) Thermodynamic and experimental evaluation of the temperature required to quantitatively remove oxygen from a fluoride melt; (2) installation of a water and an acid trap to entrain the volatilized fluorides; (3) development of a suitable sample-preparation technique for the heterogeneous fluoride baths in which both pulverizing and pelletizing were necessary to achieve reproducible results; (4) comparison of platinum flux and dry crucible techniques, which showed that the use of platinum was not necessary. The accuracy of the method was evaluated by analyzing fluoride baths containing known amounts of oxygen added as the metal oxide. In the 0.05-to 0.5-percent range, the relative error was about ±5 percent.

Jan 1, 1962