Search Documents

By S. Kamalpour

It has been observed that the productivity of ferromanganese furnaces, and the stability of metal and slag compositions, vary considerably according to the type of coke used as reductant. However, the desired properties of coke for optimum furnace performance are not well understood. In this investigation, the behaviour of four cokes, which exhibited a wide range of performance in ferromanganese production, was investigated by means of laboratory simulations of reducing conditions in the furnace. The Stationary Charge in Controlled Environment (SCICE) technique was used to simulate the conditions in the furnace shaft. Batches of raw materials, mixed in the same proportions as used in practice, were heated at fixed rates to 900, 1100 and 1300°C then cooled. The mass loss was used as a measure of the degree of reduction. Conditions in the lower part of the furnace were simulated by means of melt-reduction experiments in which lumps of coke were drilled out to form crucibles in which enriched ferromanganese slags were reduced at 1500 and 1550°C then cooled. An examination of the raw materials and the cooled, reacted charges using a variety of analytical and characterization techniques enabled the sequence of reaction and changes in morphology of the raw materials to be followed. This enabled an understanding of the behaviour of the cokes during reduction to be developed, which was then used to explain the observed performance of the cokes in practice. By relating the observed behaviour of the cokes in the laboratory tests to measurable properties of the unreacted cokes and to their observed performance in practice, it was shown that to achieve high productivity and good furnace performance, cokes should be selected to have moderately high reactivity towards CO2 (Boudouard reactivity) relative to conventional iron blast furnace cokes.

Jan 1, 2004

By A. K. Majumder

Particle motion in fluids is a subject of considerable practical importance to engineers working in fields such as hydraulics, river mechanics, chemical engineering and mineral processing. Many mathematical models have been proposed to predict the terminal settling velocities of particles in a fluid medium. The selection of an appropriate mathematical model has, therefore, become a challenging task for practicing engineers. This paper reports on an attempt to identify some of the useful models found in the literature for predicting particle-settling velocities in a fluid under free- and hindered-settling conditions. From this study, it was concluded that there is no well-accepted model validated by experimental data available for predicting particle hindered-settling velocities in a suspension of polydisperse and polydens particles. Collective efforts should, therefore, be made towards developing a hindered-settling model, as this is an absolute prerequisite for many model structures in mineral processing and other engineering disciplines.

Jan 1, 2007

By J. B. Cheung

The results of a program to demonstrate the technical feasibility of hydraulic borehole coal mining are presented in this report. The hydraulic borehole method of coal mining involves inserting a hydraulic mining device into a borehole that has been drilled from the surface into the underground coal bed. The borehole mining device issues a jet of water under high pressure, which breaks the coal. These pieces of coal, along with the water, form a slurry, which flows to the base of the borehole where it is pumped to the -surface. Phase I of the program encompassed the design, fabrication and factory-testing of a hydraulic borehole mining device. The program was successfully completed with the field tests being conducted at the Wilkeson-Carbonado Coal Field near Wilkeson, Washington. The technical feasibility of hydraulic borehole coal mining was demonstrated by mining 32 tons of coal at a depth of about 75 ft over a period of 4 hours.

Jan 1, 1976

By David S. Bowling

The ER-300 Series White Recorders were developed to provide on economical, yet invaluable instrument for those who desire permanent recordings of such data OS displacement, vibration, concussion (air borne effect) and velocity information. The precise monitoring of earth displacements and air blast magnitudes aids quarrymen and construction contractors in estimating safe blasting limits when operating in populated areas. A refraction model is available for recording velocities which permit the determination of weathered zone depths as well as the .depths to other subsurface formations. The dual purpose (Refroction- Displacement) systems ore utilized for velocity studies and displacement - oir blast measurements.

Jan 1, 1990

By D. Rendini, R. D. Gutridge

INTRODUCTION Gwinnett County, Georgia, is a part of the rapidly expanding metropolitan Atlanta Georgia area. Located approximately 48 km (30 miles) northeast of Atlanta, Gwinnett County has a current population in excess of 600,000 and is projected to reach a population of 1,200,000 by 2025. As a part of the County’s master plan to supply drinking water for the expanding population and to increase system reliability, the Gwinnett County Public Utilities Department undertook the Shoal Creek Raw Water Intake and Pump Station Project. Figure 1 shows a vicinity map for the project. Prior to construction of the Shoal Creek Raw Water Intake and Pump Station Project the County had a single raw water intake to feed water from Lake Sidney Lanier (Lake Lanier) into a filter plant for processing into potable water. This project together with a newly constructed water filter plant provides Gwinnett County additional capacity and system redundancy to prevent interruptions to the drinking water supply. Lake Lanier is a man made reservoir with over 800 km (500 miles) of shoreline and was constructed by the Army Corps of Engineers in the 1950s for hydro electric power generation, flood control, and navigation benefits for the Chattahoochee River. Over time, Lake Lanier has become an increasingly important source of drinking water for the metropolitan Atlanta area. This paper focuses on the primary underground construction and lake tap components of the project including a 42.7 m (140 ft) deep pump station shaft 24.4 m(80 ft) in finished diameter transitioning to a 6.1 m (20 ft) finished diameter shaft, a3.05 m (10 ft) finished diameter by 19.8 m (65 ft) deep intake shaft constructed in an average of 21.3 m (70 ft) of water, and a 190.5 m (625 ft) by 3.05 m (10 ft) finished diameter modified horseshoe tunnel connecting the two shafts. This raw water intake system, in conjunction with the incorporated pump station with 8 pumps and dual1,829 mm (72 inch) pipelines, provides a system capacity of 1,091,062 m3/day(240 MGD) to two water filter plants and is expandable by the addition of pumps to1,500,210 m3/day (330 MGD). Parsons provided design and construction management services for the project. The $29.6 million contract to construct the project was awarded to W.L. Hailey &Company. Notice to proceed was given August 6, 2001 and substantial completion was achieved on January 20, 2004. Value engineering changes adopted for the project contributed to completing the project at a final cost of $28.8 million.

Jan 1, 2005

Controlled Blasting, Inc. (CBI) located in Norcross, Georgia recently teamed with the Dekalb county fire marshals office to stage a mock disaster to test new trainees of Community Emergency Response Team (CERT). It as an interesting example in which industry can help out the community and government through the use of explosives.

Jan 1, 2010

Forecasting, particularly when applied to meaningful issues, is known irreverently as 'futurology'. There is quite a range of opinion ext.ant in the world when mineral resources are looked at. The opinions range from the doomsday view that there will be acute shortages of all essential commodities, to the optimistic outlook that new 'discoveries will prevent any possibility of shortages. The environment is, as yet, only studied locally and quite parochially; surprisingly there is little integration when considering the spatial atmosphere, the seas in depth and the earth's crust.

Jan 1, 1981

The paper reviews the results emanating from an experiment conducted in Bochum?Germany in which various international rope inspection authorities were requested to assess the conditions of a corroded rope sample as well as a rope sample containing internal fatigue breaks. Both samples were of the multi-layer low rotation construction.

Jan 1, 2000

By R. Emmett Hughlett

The Bureau of Mines has developed a statistical approach to the laboratory evaluation of response bias and precision in gas detectors. The techniques described employ a computerized analysis and a new method of data presentation called composite graphing. The underlying theory, its practical application to the data, and the experimental equipment and procedure are described.

Jan 1, 1982

This publication summarizes, for potential contractors and other interested parties, the research, development, and demonstration contract projects programed by the Bureau of Mines for fiscal year 1982 (October 1, 1980 -September 30, 1981) under its Minerals Health and Safety Technology program. Contingencies may require that a significant port ion of the program be deferred into fiscal year 1983. The objective of these projects is to provide an ordered and sequenced series of advances toward the Bureau's overall goal of providing the systems technology required to create a healthier and safer working environment for the Nation's mining and minerals processing workers.

Jan 1, 1981

The development and introduction of a preventive maintenance scheme in the coke ovens department, coal preparation section, of The Broken Hill Proprietary Co. Ltd., Newcastle steelworks, is described together with its operation and the results achieved during the first 12 months.'fhe scheme consists essentially of an engineering analysis of the plant to establish maintenance schedules, and to record the details on reference cards.Items are reviewed progressively and a weekly work schedule is prepared, from which work orders are passed on to the maintenance foremen. These foremen in turn originate action orders and issue inspection sheets as required. Results are then reported back to the maintenance planner and used to revise norms, practices, and cycles.INTRODUCTIONWhat is maintenance? Some people consider maintenance to be the work involved in putting things together again after they have fallen apart. The author regards it as the mechanical care and repair of plant machinery and equipment to keep it operating in sound mechanical condition, without undue interference with production processes.Maintenance may be organized or haphazard, and, too often, what has been fondly imagined to be nicely controlled and organized maintenance proves, under pressure, to be more correctly described as haphazard. Haphazard maintenance deals with breakdowns as they occur, and frequently finds itself confronted with more breakdowns than can be handled. Even organized maintenance, if not based on sound planning, can, at times, be found in a chaotic state, because of unexpected and unanticipated breakdown.Properly planned and scheduled maintenance permits an orderly and controlled approach to the problem of maintain...

Jan 1, 1961

"Drilling twinned holes is a traditional technique used for verification of intersections of high-grade mineralization, testing of historic data, or confirmation of drillhole data during geological due diligence studies. Twinned holes can also be used for special tasks such as correcting earlier data that are recognized to be biased. Successful implementation of the twinned-holes technique requires thorough planning. Experience suggests that good practice is to drill twinned holes no more than 5 m apart. Many unsuccessful twinned-holes programs could possibly have failed because the twinned holes have been drilled too far apart.Twinned holes are best compared by mineralization intersections and, if the data and geological characteristics of the deposit permit, by samples, equal-length composites, or geological units. Variables to be verified by twinned holes should include the thicknesses of the geological units of interest (e.g., mineralized thickness) as well as the presence of significant geological features (e.g., ore/mineralization contacts, alteration, etc.).A formal, rigorous analysis of twinned-hole data is essential. Repeatability of sampling, analytical results, and bias must be analyzed and statistically quantified. The number of twinned holes required for conclusive statistical and geostatistical analysis can be as high as 20-30, in particular where the studied variables are characterized by high short-range (local) variability.The efficiency of this approach is demonstrated by several examples of successfully applied twinned-hole projects, including applications to orogenic gold, mineral sands, bauxite, and iron ore deposits."

Jan 1, 2009

By E. A. Sarver

The Fe(II) regeneration process is an important aspect of Alternate Anode Reaction Technology (AART) for copper electrowinning (EW). In AART, Fe(II) is oxidized to Fe(III) at the anode during EW, and it must be regenerated to maintain recyclable electrolytes. Regeneration is achieved via Fe(III) reduction by SO2(aq), and the reaction is catalyzed by activated carbon particles. To better understand this process, a kinetic model was developed and experimentally validated for the Fe(II) regeneration in the current work. The investigation focused on the primary reaction mechanism and the reaction rate dependence on four variables: carbon particle size, flow rate, initial Fe(III) concentration and initial SO2 concentration. The Fe(II) regeneration reaction is mass-transfer controlled in the presence of activated carbon. Carbon particle size and initial Fe(III) are the most influential factors under the conditions tested. Initial SO2 concentration is insignificant to the reaction rate.

Jan 1, 2007

A single aggregate mix design was developed based on a slag/Portland binder blend and crusher sand. The primary design criterion, after performance, was the fluidity of the shotcrete and concrete product to ensure compatibility with existing manufacturing and shotcrete equipment as well as the pipeline transport system Cullinan Diamond Mine was investigating. Initial work had determined an optimum slag/Portland to aggregate ratio while retaining a water to slag/Portland binder ratio of approximately 0.4 to maintain the flowability of the product. A super-plasticizer was used to further increase the flowability of the product as opposed to increasing the water content. Finally a polypropylene reinforcement fibre was included in the wet shotcrete product to improve the energy absorption characteristics of the shotcrete. Previous work on the strength development of the slag/Portland based shotcretes and concretes suggests that strength class based on the EN 206 specification is C40/50 while the toughness classification based on the EFNARC plate test is c, or greater than 1000 joules1. Typically, Cullinan Diamond Mine wanted a shotcrete with a uniaxial compressive cube strength of 45 MPa and an energy absorption, based on the EFNARC plate test, in excess of 700 joules. This is an EN 206 strength class of C36/45 requiring a uniaxial compressive core strength of 30.5 MPa and a toughness classification of b1. In addition to the shotcrete development, Cullinan Diamond Mine required concrete products with a compressive strength range of between 25 and 60 Mpa for differing construction operations underground to be manufactured from the same mix design and raw materials as for the shotcrete. Finally, Cullinan Diamond Mine carries out extensive dry shotcrete operations and an investigation into the possibility of using the single aggregate mix design for dry shotcreting was also entered into. This paper presents data that indicates that, under the terms of reference, a wet and dry shotcrete and concrete product appears to be possible from a single aggregate less than 6.7 mm in size, and that a slag/Portland binder is suitable for use as the hydraulic binder in all the products, and that the necessary performance parameters of strength and energy absorption can be achieved.

Jan 1, 2006

By A. R. Barnes, N. O. Lotter

Recoverable economic copper sulphide minerals such as chalcopyrite, bornite, chalcocite and covellite often occur together in varying proportions in the major copper-bearing ores, and have individual flotation requirements and characteristics. Pyrite also occurs in these ores to varying extents as the sulphide gangue, and is problematic because of its natural tendency to float quickly and easily. In a bulk sulphide float, selectivity against pyrite is desirable, particularly if it does not host other paymetals such as gold or silver. At the same time it is a requirement to float all of the copper sulphides despite their electrochemical differences. The electrochemistry and semiconductor properties of these minerals are reviewed, together with implications for flotation with and without collector addition. Mixed collector systems for the improved flotation of these sulphides are proposed as a solution. The use of xanthate and dithiophosphate in the collector suite allows the co-existence of dixanthogen and free dithiophosphate radical because the latter has a higher redox potential requirement than xanthate to oxidise to the dithiolate. Because some of these minerals require dixanthogen, and others, free thiolate, to generate surface hydrophobicity, a bulk flotation of all the species becomes possible in the overlapping area of Eh and pH between the two dithiolate equilibrium lines on the Pourbaix diagram. The arsenic-signature copper minerals are added to the study, since many copper operations encounter arsenic as a penalty element in the saleable concentrate. It is shown that the addition of arsenic to the copper and iron sulphides alters the semiconductor and electrochemistry properties, and in turn, its flotation characteristics. The degree of mineral association and liberation between these minerals can be a complicating factor due to textural associations, and should also be considered in the process as a next step.

Jan 1, 2016

By P. van Dorssen

In South African metalliferous mines, stoping operations are largely confined to narrow, tabular orebodies making mechanization extremely difficult. Limited flexibility in terms of stope width has necessitated drilling by means of handheld, pneumatic rock drills at most of our operations. As the largest producer of platinum in the world, we drill in excess of forty million stope blast holes per annum. Cleaning of the broken ore is also done by conventional means?utilizing scrapers and scraper winches. Conventional methods such as these carry high costs in terms of risk exposure as well as labour intensity. The purpose of this paper is to describe the development of a long hole stoping system suitable for the narrow platinum reefs. The new system had to be substantially safer and more cost effective than conventional mining. We selected a site that was conducive to mechanized mining and set out the parameters that we considered would meet our requirements. We then conducted a feasibility study to evaluate the conceptualized long hole stoping system in terms of specific goals. An analysis of the proposed system identified the Key Performance Indicators (KPIs). One of the most critical goals was to be able to create a man-free stope. This would mitigate the safety risk associated with normal stoping operations, as well as the inefficiency cost previously referred to.

Jan 1, 2002

By J S-L Chan

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Cu-Ag-Au mineralisation at Kluwih prospect in Eastern Java, Indonesia is related to a high-sulfidation hydrothermal system within a volcanic dome (2.35 × 1.7 km diameter). The mineralisation occurs mainly in steeply dipping, structurally-controlled quartz-enargite-pyrite veins (several centimetres to 2 m wide) and is hosted mainly in porphyritic dacite, volcaniclastic rocks and volcanic breccia of the dome and in an underlying andesite that yielded a zircon U-Pb age of 11.5 Ma.Short wave infrared spectrometer analyses were carried out for alteration mapping at Kluwih. There are two main stages of alteration produced by the hydrothermal activity. The alteration mineral assemblages indicate an advanced argillic alteration. The Cu mineralisation occurred in the form of enargite and subordinate chalcopyrite with an intergrown texture in the early stage. These mineralised veins are characterised by narrow pyrophyllite ± diaspore and dickite selvages (metres wide) and a peripheral K-muscovite envelope (sericitic alteration) up to 100 m wide. The K-muscovite envelope is zoned outward to Na-muscovite or Na-illite. Late-stage kaolinite and smectite alteration overprints the porphyritic dacite and may obscure the nature of early mica-clay alteration. The spatial distribution of different alteration assemblages suggests that the temperature of hydrothermal fluid increases with depth.Both the high-sulfidation mineralisation and advanced argillic alteration are suggested to be related to magmatic-hydrothermal fluids, which are likely to originate from an undiscovered deeper porphyry Cu-Au system below the porphyritic dacite. Based on alteration mapping results and comparisons to similar deposits, the porphyry intrusion could be up to 500 m below the volcanic dome. Further geochemical and mineralogical studies may help to target the potential underlying porphyry system.CITATION:Chan, J S-L, 2015. High-sulfidation epithermal Cu-Ag-Au deposit, Kluwih, eastern Java, Indonesia – alteration and implications for potential porphyry cu mineralisation, in Proceedings PACRIM 2015 Congress, pp 213–218 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By T Burns, P Savory

In 2013, Rio Tinto Iron Ore (RTIO) produced 251 Mt from 15 mines in Western Australia. Throughout the mines, Ore Reserve models are used for long-term and medium-term mine planning. Grade control data aids the accuracy of short-term planning. Reconciliation of models with grade control data is important for maintaining confidence in predictions from the models, understanding the limitations of the models, and identifying issues that may require further work.There are a large number of sites and models, with more than 200 professionals involved in different parts of the reconciliation process. Regular meetings of all involved and enabling effective communication are important in the reconciliation process.Reconciliation data is gathered and processed through a web-based system; Grade Block Reconciliation System. This system cuts each grade block against the required model, stores the results, and allows users to view and analyse the data. Development of this system has occurred over a number of years and all Rio Tinto Iron Ore mine geologists and resource geologists now use it as standard to report reconciliation results. The results can be viewed in many ways including by different time periods or benches. Graphing the results assists identification of trends. Centralising and standardising reconciliation has allowed easier comparison between sites. Flexibility in the system allows users to customise reports to manage issues unique to their particular site.In parallel with system development, substantial effort has been put into ensuring mining professionals get together to discuss and understand reconciliation issues. To facilitate this there are now regular sessions, including site visits. Issues are assessed on a case-by-case basis and decisions on how best to address the issues are made by the relevant stakeholders. Reconciliation reports and action plans are revised each quarter.CITATION:Burns, T and Savory, P, 2014. Reconciliation of orebody model predictions – system and people, in Proceedings Ninth International Mining Geology Conference 2014 , pp 367–376 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By T. A. Klinefelter

ONE OF THE many services rendered by the Federal Bureau of Mines is the identification and general examination of ore and mineral samples. Many of these, coming from almost every State in the Union, are clay and shale samples. Other Government agencies, State geologists, universities, and other laboratories are often requested to make similar examinations. This publication describes methods of testing these samples. An earlier paper, published in 1943, described Bureau of Mines methods of testing such clays.3 This paper was to be followed later with another (part II) that would describe much more thorough testing than did the rather general outline of part I. Part I has been out of print for some time and needs revision, and part II was never written; hence, the present publication is designed to include part I and also those additions intended as part II. The tests presented in part I were simple, requiring only the ordinary equipment to be found in any good chemical laboratory. The second publication was to include a greater number of test procedures and information on increasing the accuracy and precision of those previously given.

Jan 1, 1957

By Bernard Kopelman

THE particle size of tungsten metal powder used to make tungsten wire for use in radio tubes and incandescent lamps must be closely controlled if the highly desirable feature of nonsagging is to be achieved. Our knowledge of factors affecting the particle size of tungsten powder has been limited by lack of any extensive literature on the subject. There are no publications in the English language discussing this problem in any but the most general terms. In this paper the published experimental information on this subject is reviewed. Based on the published data and some experimental data obtained by the author, a general theory of factors affecting the particle size of tungsten metal powder obtained by reduction of the oxides in hydrogen is offered. The various forms of the tungsten oxides and tungsten metal used in the experiments described were those prepared by com¬mercial processes, so that the experimental results obtained on a laboratory scale would be more directly applicable to actual commercial reduction conditions. The effects of time of reduction, temperature, and concentration of water vapor in the hydrogen were observed by counting microscopically the particle distribution obtained. Such a method is very time-consuming, but the data obtained by this method are more reliable and more fundamental than those obtained by any of the several instruments available for measurement of particle size. REVIEW OF THE LITERATURE Until the year 1912, tungsten powder was prepared commercially by reducing tungstic oxide in the presence of carbon or one of its compounds (such as glycerin or ethylene glycol), usually by firing the mixture in a closed fire-clay crucible. The resultant powder contained about 95 per cent tungsten.1 When reduction of tungsten oxides by H2 was introduced commercially, 2.1 several investigators became concerned with the equilibria between tungsten metal and its several oxides in an atmosphere of hydrogen and water vapor.4-13 While these many investigations were in fair agreement on the equilibria there arose considerable controversy as to the chemical composition of the oxide between W03 and W02, because of very poor agreement on the equilibrium constant of this intermediate oxide reduction reaction. The controversy on this intermediate oxide has been in progress for more than 10o years. Thus Malguti,14 in 1835, decided it was W02.56. In 1857, Riche" proposed the formula W308. Usler,16 in 1865, confirmed the existence of W308 and further proposed W4O11. In 1897, Desi17 agreed upon W308 but also found W5014.

Jan 1, 1946