Search Documents

By Zsuzsanna Zborovszky

[Certain chapters of the tentative document entitled, "Test Requirements for instruments & Apparatus to be Considered for MESA Intrinsically Safe Certification" are evaluated and supporting data are presented on certain key issues with the purpose of helping the regulatory agency in improving the above document. The subjects discussed in detail are: hot wire ignition with W and BeCu wires; the most sensitive methane-air :and propane air ratio; the ignition limits for inductive-resistive circuits in 8.3°; methane-air mixtures in the 24-OV, 100 mH-2 [ ]H range, the resistive ignition limit as a special case when L ? 0; the capacitive-resistive ignition limit representing a four ,dimensional problem is analyzed and discussed in general and the variation of the ignition limit using Vo and/or r2 as a parameter are determined experimentally. The ignition limit is also determined for the [r1 ,~ r2] = 0 case ("capacitor alone") and for the most dangerous capacitive resistive circuit combination. The ignition limits are below the limits proposed in the document. A survey of the different factors influencing the ignition is made as to their suitability to provide a constant safety factor. It is shown that a constant safety factor cannot be achieved. The best method for applying a safety factor appears to be the increase of initial pressure or use of other gas mixture. The revision of the safety factor concept and ignition limit curves is recommended.]

Jan 1, 1980

By I. Gil, J. -C. Roegiers

Abstract Hydraulic fracturing is a technology that has been utilized for more than 50 years in the oil industry. It was originally used for stimulating hard, brittle formations which typically exhibit low permeabilities and roughly linear elastic behavior. Nonetheless, an increasingly important segment of the industry is currently stimulating very soft and poorly consolidated formations; where the assumptions of ideal elasticity and relatively small fluid leakoff fail to hold (e.g. Gulf of Mexico, West Africa, Alaska, East China). In these rocks, hydraulic fracturing stimulation has been used for several years to control and solve critical production problems such as sanding and formation damage (caused during completion and drilling operations). Although successful1, the application of this method has not been accompanied by robust fracturing modeling techniques. In addition, long term production increases were often not materialized. In other words, engineers have been able, via trial-and-error, to avoid major ‘operational’ problems but with no optimization of such treatments. Thus, most hydraulic fracturing projects carried out in poorly consolidated rocks render unexpected results. A recent worldwide survey on net pressures by the Delft Fracturing Consortium (Papanastasiou, 1997) indicated that net pressures encountered in the field are 50% to 100% higher than the net pressures predicted by conventional fracturing simulators. The difference is yet higher for the case of poorly consolidated formations (Pak, 1997). The theory for the construction of a fully coupled elastoplastic three-dimensional hydrofrac simulator, specifically conceived for unconsolidated rocks, is presented in this paper. This novel model calculates the dimensions and changes in shape of the fracture(s) being created during hydraulic fracturing operations. No assumptions are made regarding either shape or geometry of the crack(s). Three main failure criteria are used simultaneously in this model: tensile and shear stresses, and volumetric strain. Incremental forms of the governing equations of equilibrium and fluid flow are presented. The scheme chosen for solving this problem is the finite elements method, which allows both equations to be solved simultaneously at any instant in time. Résumé La fracturation hydraulique est une technologie qu’a été utilisé pour plus que 50 ans dans l'industrie pétrolière. Elle a été utilisée au début pour stimuler les formations dure et fragile que typiquement ont des perméabilités basses et un comportement élastique à peu près linéaire. Néanmoins, un segment plus important de l'industrie stimule actuellement des formations mal consolidées; où les suppositions d'élasticité idéale et de relativement petite fuite de fluide ne se tiennent pas raison (par exemple le Golfe de Mexique, l'Afrique d'ouest, Alaska, la Chine de l'est). Dans ces roches, la stimulation avec fracturation hydraulique a été utilisée pour plusieurs années pour contrôler et résoudre les problèmes critiques de production comme les dommages de formation et d’ensablement (causé pendant les opérations de l'accomplissement et forage). Bien que prospère, l'application de cette méthode n'a pas été accompagnée de techniques robustes pour le modelage de fractures. En outre, les augmentations à long terme de production n'ont pas été souvent concrétisées. En d'autre termes, les ingénieurs ont pu, via le procès et l’erreur, éviter les majeur problèmes ‘opérationnel’ mais avec aucune optimisation de tels traitements. Ainsi, la plupart des projets de fracturation hydraulique ont été exécuté dans des roches mal consolidées et ont rendu résultat totalement inattendu. Une récente étude mondiale sur les pressions nettes par le Consortium Delft pour Fracturer (Papanastasiou, 1997) a indiqué que les pressions nettes qu’ont été rencontré dans le champ sont environ 50% à 100% plus hautes que les pressions nettes prédites par les simulateurs fracturant conventionnels. La différence est pourtant plus importante pour le cas de formations mal consolidées (Pak, 1997). La théorie de construction d'un simulateur elastoplastic d’hydrofrac à trois dimensions entièrement couplé, en particulier conçu pour les roches non consolidés, est présentée dans ce papier. Ce nouveau modèle calcule les dimensions et les changements dans la forme de(s) fracture(s) étant créé pendant les opérations de fracturation hydraulique. Aucune supposition n’a été faites en ce que concernant la forme ou la géométrie

Jan 1, 2003

By B. N. Das, P. A. Beck

THE o phases have a complex tetragonal structure with Lo/ao = 0.52 and 30 atoms per unit cell.1 A large number of such phases are now known to occur in various binary systems of the transition elements and they exhibit the following typical features: 2,3 The composition of binary o phases is variable, ranging from approximately A4B to ABI. With only a few exceptions, in the o phases the A-ele-ment comes from the V- or Cr- group of the periodic table, while the B-elements are from the Mn-, Fe-, Co-, or Ni- group. In the first long period the corresponding o phases of the V- and Cr-series have approximately the same compositions. However, as the B-element changes from Mn to Fe to Co to Ni, the mean composition shifts monotonously toward higher A-contents.2-4 For example, if the mean compositions of the various o phases with vanadium are compared with each other, the composition shift mentioned above becomes plainly visible: V 30Mn0 80 Vo.45Feo..,, Vo .,Coo. 45 and Vo.5Nio.3. Similiar composition shifts, although not the same composition values, were observed in u phases formed by second and by third long-period transition elements.3'4 This behavior, very characteristic of o phases, is in rather sharp contrast to the usually quite well-behaved stoichi-ometry of the Laves phases. In the latter, the AB2 stoichiometry predominates, with A the large atom and B the small atom.= The p phase occurs in the four binary systems of Mo or W with Fe or Co. On the basis of their crystal structure determination, Arnfelt and westgren6 ascribed to the p phase in the Co-W system the ideal composition W,Co7. Since all four binary pphases have nearly the same composition, it would seem quite plausible that some definite stoichiometry such as A6B7, might be characteristic of this phase, as AB2 is of the Laves phases. On the other hand, it has been noted,7 that the phases occur at average electron concentrations near to those at which the various cr phases are found. Also, it has been pointed out by Shoemaker and associates8 that structurally the a phases and the p phases are somewhat related to each other; both of these structures may be described in terms of suitable stackings of quasi-hexagonal layers'of atoms. By studying a suitably chosen ter- nary phase diagram, one might expect to be able to find out which one of the two conditions, the analogy with the o phase or the constant ratio between the number of large atoms and the number of small atoms in effect governs the behavior of the p phase. Several isothermal sections of ternary systems containing o phases have been investigated. In all cases where two binary o phases occur, these were found to be connected b a more or less straight ternary o phase field.7' '10 Such elongated o phase fields were also found in ternary systems in which only one of the limiting binaries is known to contain o phase. In this manner a latent o forming tendency could be detected and the virtual composition of a "binary o phase", which does not actually occur as such was approximately determined by extrapolation. The behavior of the phases, including their composition shift, is analogous to that of the classical electron compounds, as described by Hume-Rothery.11 In order to decide whether the p phase is essentially a "size compound" like the Laves phases, where a fixed stoichiometric ratio is quite generally maintained between the "large atoms" and the "small atoms", or whether the p phase is typically an "electron compound" in the same sense as ois, it was decided to investigate an isothermal section of the Mo-Mn-Co system. The Mo-Co system12 and the Mo-Mn system13 each are known to have a binary o phase. It could be therefore expected that a ternary o phase field will connect these two binary cr-phase fields. The p phase is known to occur in the Mo-Co system. If the p phase should turn out to form an elongated phase field extending deep into the ternary system, the following considerations mighto apply. The atomic radius of manganese (1.314for C.N.12) is between the va,lues for Mo (1.40Afor C.N.12) and for Co (1.26Afor C.N.12). If it is assumed that p is a "size compound", and that Mn is substituting for the smaller Co atoms in the p-structure in the ternary system, the y-phase field might be expected to extend parallel to the Mn-Co binary line. If Mn is substituting for the large Mo atoms in the p-structure, the p-phase field may be expected to extend parallel to the Mn-Mo binary line. On the other hand, if the p-phase turns out to be an "electron compound" like o, the ternary p-phase field should extend parallel to the ternary o -phase field connecting (Mo,Mn)owith (Mo, Co) a

Jan 1, 1961

By Homer J. Ballinger

During the fall of 1943 and spring of 1944, the Bureau of Mines investigated nine secondary limonite iron-ore deposits in the Williamsville district of Wayne, Butler, and Ripley counties, Mo., by rotary-bucket and power-auger drilling test pitting, and trenching. Studies on beneficiating the ores were made at Bureau laboratories. Iron ore has been mined in Missouri since 1825, and iron mining reached its greatest development between 1870 and 1890. During this period, production averaged about 250,000 tons annually.

Jan 1, 1948

By Timothy C. Siegel

Accurate representation of the geotechnical resistance distribution is critical in evaluating the performance of piles and pile groups for design. A current practice is to infer the geotechnical resistance distribution based on measured changes in strain during conventional top load pile testing. Especially for drilled and bored piles, the residual load is typically assumed to be negligible both during testing and after the application of the structure load. A practical result is that the compressive structural load is anticipated to be opposed primarily by the shaft resistance with little or no mobilized toe resistance. The predicted top deflection is estimated as the combined elastic compression plus the movement necessary to mobilize shaft resistance. The development of residual load (and associated negative skin friction) results in a significantly different design condition. Negative skin friction tends to force the pile into the ground and develops residual load in the pile that contributes to the internal compressive load. Significant toe resistance can be mobilized in order to resist the combination of negative skin friction and the sustained compressive load. The pile movement becomes a function of the toe penetration required to mobilize sufficient resistance to reach a balance of forces. In an effort to study the development of residual load in augered cast-in place (ACIP) piles, the authors installed and monitored strain gages that were embedded in an 18-inch diameter ACIP pile at a site in southeast Georgia. The results of this study indicate that residual load develops over time and reaches a distribution that is consistent with the principles of the unified design of piles. It is concluded that residual load develops in ACIP piles (as well as all drilled and bored piles by the same mechanisms) and that the residual load should be considered in the interpretation of load tests and in the pile design, particularly in the estimation of the single pile and pile group settlement.

Jan 1, 2009

By David Norval

Water solidification of mattes, metals, alloys and certain slags with high metal entrainment has customarily not been practiced due to the belief that such processes are too dangerous and unproven in the Pyrometallurgical Industry. Slag granulation on the other hand is extensively applied, although in some cases crudely, with disastrous effects, as a result of not recognising the high heat capacities prevalent in slags. This paper will examine the most common air solidification processes and compare such processes with water solidification, mainly slag and matte granulation processes and design criteria for safe and reliable operation. Finally, purpose designed granulation and solidification processes will be discussed taking into account specific applications and the individual signatures of alloys and slags, emphasising that no slag, matte or alloy responds in similar fashion to a granulation practice.

Jan 1, 2006

By O. C. Blade

In its general study of crude petroleum, the Bureau of Mines has published several reports that include analyses of samples of crude petroleum from Oklahoma fields3/. This report discusses briefly the properties of crude oil samples collects in come of the major producing Yields in the State. ACKNOWLEDGMENTS This investigation was conducted by the Bureau of Mines in cooperation with the State of Oklahoma. The study was via e under the general supervision of R. A Cattell, chief engineer, petroleum and Natural-Gas Division, Bureau of Mines, Whishington, D. C., and N. A. C. Pith, supervising engineer, Petroleum Experiment Station, Bureau of Mines, Bartlesville, Okla., and. Under the direct supervision of Ludwig Schmidt, senior petroleum engineer, Bureau of Mines, Bartlesville, Okla.

Jan 1, 1939

By Deborah A. McCombe

"There are a number of important dates that must be disclosed when a Qualified Person (QP) is preparing a technical report for securities purposes. The dates are discussed in NI43-101 and the Form of the Technical Report, NI43-101F1. •,Effective date of the technical report •,Possible revision date of the report •,Effective date of mineral resources and mineral reserves •,Date of the personal inspection (site visit) •,Signature date of the date report (execution date) •,Date of the certificate of the QP •,Date of the consent of the QP The effective date of the report is basically the cut-off date for the information that is included in the technical report. The effective date should be close to the signature date. If there is too long a period between these dates, the QP runs the risk of new material information becoming available and then the technical report would no longer be current. The effective date is disclosed on the title page of the report and on the signature page. If a technical report needs to be revised to correct problems or disclosure deficiencies identified by the regulators, the QP will normally need to include a revision date on the title page of the report to distinguish the revised version from the original version. In these circumstances, the regulators will request that the original date of the report remain on the title page and the revised date will be below it. When a technical report must be revised, the QP must resign and date the signature page of the report and provide a new certificate and consent."

Jan 1, 2003

By O. C. Blade

[In its general study of crude petroleum, tic Bureau of Mines has published several reports that include analyses of samples of crude petroleum from Oklahoma fields3/. This report discusses briefly the properties of crude oil samples collects in come of the producing fields in the State ACKNOWLEDGMENTS This investigation was conducted by the Bureau of Mines in cooperation with the State of Oklahoma. No study was made under the general supervision of R. A Cattell, chief engineer, petroleum and Natural-Gas Division, Bureau of Mines Washington, D. C., and N. A. C. Smith, supervising engineer, Experiment Station, Bureau of Mines, Bartlesville, Okla., and under the direct supervision of Ludwig Schmidt senior petroleum engineer Bureau of Mines, Bartlesville, Okla.]

Jan 1, 1939

By Ke Yang

Drilled shafts are widely used as foundation system for sound walls to resist lateral loads. The design method based on the ultimate lateral capacity, such as Broms method, is often used for sound wall foundation design. Allowable Stress Design (ASD) is currently used for deep foundation design. However, by October 2007, all states Department of Transportations are required to use the Load Resistance Factor Design (LRFD) approach for the design of foundation in highway projects. There is a need to develop a calibrated resistance factor in LRFD lateral design of drilled shafts supporting sound barrier walls. This paper provides resistance factors for design of laterally loaded drilled shafts supporting sound walls using Broms method based on the study using reliability based method and fitting to ASD method. Additionally, the resistance factors for static lateral load tests are recommended. Furthermore, a methodology to update the resistance factors using Bayesian approach by incorporating the on-site full-scale lateral load test results is presented. To illustrate the Bayesian update methodology, two lateral load tests in Colorado were employed to develop the updated resistance factors.

Jan 1, 2007

By Anil K. Beersing

Effective drainage systems are required for reclamation of mine-disturbed areas to control surface water runoff and avoid excessive erosion. For the conventional structural design approach, armouring material necessary to satisfy the design criteria should not move during the design flood event since displacement would uncover the erodible underlying materials. This paper discusses an alternative geomorphic approach for designing drainage channels and watershed landscape. The approach is based on quantitative studies of geomorphic processes operating in a watershed. A design based on the geomorphic approach replicates the configuration, channel regime, sediment volume and hydrology of natural and mature drainage systems. Movement of some armouring material is acceptable in such an approach because the channels are allowed to mature by natural degradation and aggradation, with erosion rates comparable to the natural environment. The key advantages of a geomorphic approach over a purely structural approach include reduced sizes of armouring material, geomorphologically sustainable landscapes, ?walk-away? or maintenance-free design and reduced liability in the future. The geomorphic approach is illustrated using the example of a coal mining operation in northwest U.S.A. The paper discusses field data collection, design criteria, typical design details, and construction methods.

Apr 1, 2005

By F. J. Tavera, J. A. Finch

A probe suitable for on-line measurements of gas hold-up in industrial flotation systems has been developed. It is based on an open cell for measurement of slurry-gas conductivity and a novel syphon cell for measurement of slurry-only conductivity. The desired behaviour of the two cells was demonstrated and estimates of gas hold-up were shown to be in good agreement with independent measurements. The gas hold-up probe was used as a diagnostic tool to assess the operation of flotation columns. Differences in gas hold-up between baffled sections in two industrial columns were detected

Jun 18, 1905

By Gabriella Tranell

In the manganese ferroalloys industry, there is increasing focus on the performance of different carbonaceous materials within the smelting processes. With a developing scarcity of traditional raw materials, new carbon sources are being identified for potential use in the processes. For this purpose, it is important to be able to predict the suitability of different materials in the process. Hence, the effects of both the physical and chemical properties of the carbon material on the reduction kinetics of manganese and silicon from slag to metal, have been investigated using an advanced sessile drop technique. Using this technique, the reaction patterns of SiO2-MnO containing slag droplets in contact with various solid carbon materials (graphites with different properties as well as cokes and charcoals) at 1400 to 1600\\176;C were studied in-situ. In addition, slag and metal reaction products from kinetic experimental series were analysed. From these results, differences in reactivity between various carbon materials and slags were demonstrated and explained. Mechanisms for both manganese and silicon reduction were proposed.

Jan 1, 2006

By G. Sauer

"More Skill is needed to avoid rather than to handle heavy ground loads." This finding, from a tunneling engineer of the nineteenth century, is still relevant today with all advanced sequential excavation and support methods available whether they are applied in the vertical or horizontal direction. Balanced contractual agreements and documents are important since they provide the spirit and climate at the site. This article aims to describe the means and measures for 'hand mined' shaft and tunnel support as they are available today. Some special construction elements and methods with a perspective in recent developments in order to avoid getting stuck in conservatism are presented as well. If we don't allow new methods, means and measures we may end up with the famous quote "Only women who have already proven they are able to give birth to a healthy baby are allowed to become pregnant!"

Jan 1, 2003

By Taehong Kim

An accurate and reliable prediction of Tunnel Boring Machine (TBM) performances, in terms of Rate of Penetration (ROP), utilization (U), and cutter wear rate, is a critical element in the successful planning and execution of mechanical tunneling project. Three open hard rock TBM projects were studied to establish possible trends and correlations between rock mass properties and machine performance. Based on this analysis and literature survey, three geological parameters, including RQD, RMR, and groundwater inflow rate, were identified as having the greatest impact on TBM utilization level. Rate of Penetration (ROP) and cutter wear rate were also correlated with fracture spacing, alpha angle, and Cerchar Abrasivity Index (CAI).

Jan 1, 2008

The Beckman Air Comparison Pycnometer is as accurate as the specific gravity bottle for the determination of the volume of fine powders, or particles, up to 50 c.c. in volume. The determination using the air comparison pycnometer is performed in a much shorter time.A graph of density versus iron content for samples from four different iron ore deposits shows that iron contents can be obtained to within 4 per cent iron. Field geologists should be able to obtain quick and relatively accurate iron contents of ore samples using the air comparison pycnometer at these deposits.INTRODUCTIONA Beckman Model 930 Air Comparison Pycnometer was purchased to decrease the time required for the determination of the volume of stones and powders. The liquid displacement method was used previously and the time required per determination varied from a few minutes for stones to half an hour, or more for fine powders. With the air comparison pycnometer, the determination takes approximately 2 min and can be quickly checked for accuracy by a further determination. The total time for weighing, determining, and checking the volume is no more than 5 min.DESCRIPTION AND PRINCIPLE OF OPERATION OF PYCNOMETERDescriptionThe air comparison pycnometer measures the volume of materials, in c.c., by determining the amount of air displaced.A diagram of the main components is given in Fig. l.Cylinders A and B are equal in volume and each has a piston which is moved by turning a handwheel attached to a geared shaft. The measuring piston shaft is geared to a 5...

Jan 1, 1963

By Mike Ounpuu

"Locked cycle testing has become more common practice in the last 10 years. Reasons vary from a desire to avoid pilot plant testing, demand for more variability testing within deposits, and perhaps most importantly, a request from the financial institutions who invariably finance many of the projects. Surprisingly, many people don’t understand locked cycle testing, analysis and balancing. This paper provides a brief overview of locked cycle testing, and then progresses into a more detailed discussion on the analysis and balancing of locked cycle test data. The paper endeavors to educate CMP personnel on how to determine if the test was good and if a reasonable metallurgical projection was made. The paper uses case studies to illustrate the key points.INTRODUCTIONA locked cycle test is a repetitive batch used to simulate a continuous circuit. The basic procedure has a complete batch test performed in the first cycle which is then followed by similar batch tests which have “intermediate” material from the previous cycle added to the appropriate location in the current cycle. These batch tests, or cycles, are continued in this iterative manner for an arbitrary number of cycles. The final products from each cycle, i.e. final concentrate and final tailings, are filtered and thus removed from further processing. At the end of the test, all the products, final and intermediate, are dried, weighed and subjected to chemical analysis. The test is balanced and a metallurgical projection is made.This description can be found in many of our classical textbooks for the mineral engineer 1, 2, 3,4. Unfortunately, none of these textbooks provide any discussion beyond the basic procedure. Often, they provide comments such as in Taggart’ where he states; “It is questionable whether in any case it approximates mill results any more closely than the standard batch test”. It is truly surprising that our classic textbooks promote that locked cycle tests are more art than science, and suggest that they can be of dubious value. None of the textbooks provide meaningful insight or discussion in how to assess:"

Jan 1, 2001

By Bill Shand

"Placer Dome - Campbell Mine is a gold mine located at Balmertown in the Red Lake District of North Western Ontario. During the last 50 years, the mine has produced over ten million ounces of gold.A change in ball mill grinding media was made in August 1998 from 1.5” diameter forged balls to 1.5” diameter, 18% chrome balls. This was done to reduce grinding media consumption and to potentially help flotation performance.A marked ball test done in September-October 1999 showed that, of the alloys tested, 18% chrome was the optimum for the ore at Campbell Mine. The test showed that consumption of chrome balls should be 3 times less than forged balls.In December 1999, the ball size was increased from 1.5” to 2” in an effort to reduce the amount of oversize rock discharging from the ball mill. This change in size was successful.Grinding media consumption for the ball mill decreased 73% from 1.20 kg/tonne before the use of chrome balls to 0.327 kg/tonne after the use of chrome balls. This clearly indicates that, for the ore at Campbell Mine, there is significant savings in grinding media by using chrome.Grinding ball costs were reduced by 59% from $O.88/tonne of ore milled to $0.36/tonne of ore milled representing a saving of $298,000 per year. This also clearly indicates that using chrome balls is a benefit at Campbell Mine.Test work to show that chrome grinding media is beneficial to flotation has been inconclusive so far but is still ongoing.No tests have been done to see if there would be a benefit with an even higher chrome percentage in the grinding media. Test work in this area is also planned for the future"

Jan 1, 2001

By C. J. Bise

One area of study for the Coal Mine Injury Analysis project was to illustrate how loss control can be used as a foundation for mine safety training. After an initial review of the principles of loss control, the instruments often used for worker/worksite appraisal, such as incident reporting, analysis, and investigation, workplace observation, worksite inspection, and safety audits and checklists were evaluated for their effectiveness. The findings were then applied to the continuous-miner worksite at several mines to modify the techniques for use in a highly dynamic man/machine work environment. Before the information gathered from the review of the various continuous-miner worksites was presented at the annual retraining sessions at five mines, a trainability analysis procedure was developed to separate training shortcomings from those problems resulting from improper equipment design or unsatisfactory working environments. Also, several microcomputer-based training programs were developed to aid in conveying the loss-control concepts to the trainees. Finally, the results from the implementation and evaluation of the loss-control-based training programs were documented, including the complete training script for one of the case-study mines. The procedures outlined in this study will aid mine training specialists in developing focused, pro-active accident-prevention strategies and training programs that are based on sound loss-control principles.

Jan 1, 1993

By F. S. Crawford

"After many years of safety activity in the United States in one form or another it becomes increasingly evident to those in contact with safety work that to achieve continuous good results in accident prevention there must be an aggressive organization behind the safety movement at each mine with fairly definite plan and policy. A study of the methods used by various companies and the results they have attained will be of value to the common cause of safety promotion.A study has been made of the safety records of the Menominee iron range in the Lake Superior district, and of data from the county mine inspector's report. Several companies on this iron range that have attained a certain measure of success in their work of accident prevention have given data, and a summary of their safety methods is presented.The Menominee iron range of Michigan lies in the southern portion of the upper peninsula of Michigan, bordering on Wisconsin. It consists of two main. divisions--the West Menominee Range, situated in Iron County in the vicinity of Iron River and Crystal Palls, and the East Menominee range situated in Dickinson County in the neighborhood or iron Mountain, Mich. The mines about Iron River and Crystal Falls are peculiarly subject to fires in a carbonaceous, sulphur-bearing black slate which appears in the footwall. This gives considerable trouble because fires in this material start from spontaneous heating. The methods of mining are top slicing and open stoping, working on benches along the sides of the stopes. The character of the ground varies from medium Soft ore to relatively hard ore which permits open stoping. Approximately one-third of the operating mines are equipped with a fan for main mechanical ventilation. The remainder are ventilated by natural draft. The East Menominee range is the older, top slicing having been used there for a number of years, and the timber mats have boon well developed. In common with all districts, some companies pay more attention to safety than others, although, those which do riot have the best records do pay some attention to safety.During the past three years the annual production per man employed has remained about constant, but in many mines a general decrease is shown in the accident record. The variation in the results attained can be ascribed mainly to the earnestness with which accident-prevention work is pursued, essentially regardless of the method of mining used. This is shown to be generally true, because the record indicates a steady decrease in one mine with an active safety department, while in adjoining mines with the same kind of ground and method of mining but where not such intensive attention has been paid to safety work, the accident record is high."

Oct 1, 1931