Search Documents

By Hal W. Hunt

Heavier loading and more efficient equipment is helping to keep driven piles competitive in America. Better Knowledge and testing of soils and support materials make it practical to use higher stresses; this is being strongly promoted by those directly concerned with timber, steel and concrete piles. Readily available point protection is increasingly used to assure penetration of piles without damage to full load bearing capability. Fabric drains are being installed with pile equipment to speed consolidation of soils. Sheet pile configuration has changed; production has been reduced largely because of imports. Dynamic checking of representative piles for load carrying capability is replacing conventional load testing of just a pile or two ? at much lower cost.

Jan 1, 1987

By S M. Zhang, Y X. Han, J Liu, Y J. Li

"Compared with conventional roasting and magnetic separation processes, higher reduction temperatures and stronger reducing atmospheres are used in reduction technologies to reduce iron oxides to metallic iron, which is often liberated during reduction and amenable to magnetic separation. Reduction and magnetic separation of an Australian refractory iron ore was therefore studied as a function of reduction temperature, time and coal addition. It was found that during reduction, the particle size of the reduced iron increased with reduction temperature and time. Subsequent magnetic separation tests were further conducted on the reduction products. A reduced iron powder with a Fe grade of 85.67 per cent was obtained at a Fe recovery of 87.82 per cent under optimum reduction conditions where a metallisation rate of 85.82 per cent was achieved. The mechanism involved in reduction is discussed based on XRD and SEM examinations.CITATION:Han, Y X, Liu, J, Li, Y J and Zhang, S M, 2013. Upgrading an Australian iron ore by reduction and efficient magnetic separation, in Proceedings Iron Ore 2013, pp 397-402 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By F. W. Lee

This paper purposes to outline briefly results of seismic measurements made in the vicinity of blasts in a mine and in open-quarry operations. It endeavors to examine the amplitude and frequency of such vibrations as influenced by the loading, geology, and distance from the source and includes comments on factors that may index the destructiveness of a vibration and a method for measuring the stresses produced. There seems to be no simple mathematical analysis of the transmission of seismic energy through the ground, and experimental observations are at present most feasible. SEISMOLOGIC INSTRUMENTS Instruments developed by the Bureau of Mines for recording ground vibrations from quarry blasting comprise a new type of seismometer, oscillators, and a recording oscillograph. The seismometers respond to vibrations reaching them through the earth and transmit their characteristics by electric current to the oscilloglaph, where they are recorded by a beam of light on a moving strip of sensitized photographic paper. The seismometers are so constructed that their sensitivity to earth vibration can be controlled, thus keeping the amplitude of the recorded wave within bounds on the paper. Each instrument has been calibrated against vibrations of known intensity and frequency so that correction factors are known for the idiosyncracies of each unit. Moreover, each seismometer is calibrated in the field for its particular sensitivity setting at each blast. By these controls the actual movement of the earth due to vibrations of one ten-thousandth of an inch can be accurately measured.

Jan 1, 1936

By Louis P. Domingues

As part of a study on high-temperature ceramic materials, the ammonium sulfate, carbonate, nitrate, oxalate, and sulfate salts of yttrium, lanthanum, and cerium were analyzed thermogravimetrically. The temperature ranged from room temperature to 1,500° C. Each salt was decomposed by heating at a rate of 2.5° C. per minute, and some of the salts were subjected to additional rates of 5° C. per minute or 10° C. per minute. The decomposition sequences have been identified, and the temperatures of formation of intermediate compounds and of the oxides have been determined. The minimum oxide formation temperature of a given lanthanum salt exceeds that for the similar salt of yttrium, and both exceed that for the same salt of cerium except for one cerium carbonate. Variation of the heating rate indicates a thermal lag in the materials and produces the shift of formation temperatures to higher values and loss of resolution in the weight-loss distribution as the heating rate increases.

Jan 1, 1962

By Parviz F. Rad

This Bureau of Mines report reviews laboratory and in-mine techniques for determining mechanical properties of coals, with special emphasis on the relationship between these properties and the minability of coal. An extensive bibliography is included.

Jan 1, 1973

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members) The following is a partial list of members and guests who called at Institute headquarters during the period June 10, 1917, to July 10, 1917. Guy N. Bjorge, Boston, Mass. H. H. Lauer, Allentown, Pa. A. H. Burroughs, Jr., Britannia Beach, E. C. Lee, Pittsburgh, Pa. B. C., Canada. Montrose L. Lee, Port-au-Prince, Hayti. Karl Eilers, New York, N. Y. Eugene McAuliffe, Paducah, Ky. H. S. Emlaw, Grand Haven, Mich. R. H..McMillen, Pittsburgh, Pa. W. R. Hamilton, San Francisco, Cal. L. D. Moore, Providence, R. I. Fred N. Hays, Sharon, Pa. Fred J. Pope, New Rochelle, N. Y. E. Hibbert, Nickelton, Ont., Canada. George S. Rice, Washington, D. C. Charles Janin, San Francisco, Cal. W. G. Swart, Duluth, Minn. Milton A. Allen has resigned his position with the Federal Lead Co. and accepted a position with the Arizona State Bureau of Mines, Tucson, Ariz. L. W. Bahney has resigned as Professor at Yale University and accepted a position as metallurgical engineer with the Scovill Manufacturing Co., Waterbury, Conn.

Jan 8, 1917

By P. A. Davies

Paper presented at the conference: Risk assessment in the extractive industries, held in Exeter, UK, 23-24 March 1994, and first published London: IMM, 1994, preprint volume, 11pp., 15 refs. Hazards such as vibration, dust emission and fragment projection can result in an area called the Danger Zone being set around a blasting site. Traditionally Danger Zones have been set solely on the basis of consequences (e.g. based on the maximum distance of rock projection or expected ground vibration plus a defined safety margin). Advances in risk assessment and its growing acceptance as a safety management tool have led to the setting of Danger Zones based on both consequences and frequency of occurrence. This allows distances to be optimised on the basis of acceptable risk levels rather than the potential consequences of infrequent events. The setting of a flyrock Danger Zone is used to demonstrate a risk-based approach compared with a traditional consequence approach

Aug 1, 1995

By Philip C. Tully

This bibliography contains 3,062 different citations to technical and scientific literature about helium and alpha-particles abstracted by 13 abstract service publications during 1963. Multiple subject classification has increased the total number of entries to almost 5,000. Helium citations are listed by 23 major classifications. The number of subclassifications has been greatly increased to minimize the time required for literature search. The use of automatic data processing has been extended in compiling the bibliography.

Jan 1, 1970

By P J. Hommert, D S. Preece

"Commercial development of the United States Oil Shale reserve will require substantial amounts of mining. In fact, even a modest 500,000 barrels per day industry requires a mining effort equivalent to nearly half of the current U.S. coal mining industry. Obviously, mining efforts on this scale will benefit from technological advances. There are a number of areas where advanced technology could impact mining. These include continuous miners, shale transport systems, and blasting. This paperexamines recent developments in computer modeling of blasting and assesses the likelihood of these advances being applied to practical oil shale mining problems."

Jan 1, 1989

By F. W. Lee

This paper purposes to outline briefly results of seismic measurements made in the vicinity of blasts in a mine and in open-quarry operations. It endeavors to examine the amplitude and frequency of such vibrations as influenced by the loading, geology, and distance from the source and includes comments on factors that may index the destructiveness of a vibration and a method for measuring the stresses produced. There seems to be no simple mathematical analysis of the transmission of seismic energy through the ground, and experimental observations are at present most feasible. SEISMOLOGIC INSTRUMENTS Instruments developed by the Bureau of Mines for recording ground vibrations from quarry blasting comprise a new type of seismometer, oscillators, and a recording oscillograph. The seismometers respond to vibrations reaching them through the earth and transmit their characteristics by electric current to the oscillograph, where they are recorded by a beam of light on a moving strip of sensitized photographic paper. The seismometers are so constructed that their sensitivity to earth vibration can be controlled, thus keeping the amplitude of the recorded wave within bounds on the paper. Each instrument has been calibrated against vibrations of known intensity and frequency so that correction factors are known for the idiosyncracies of each unit. Moreover, each seismometer is calibrated in the field for its particular sensitivity setting at each blast. By these controls the actual movement of the earth due to vibrations of one ten-thousandth of an inch can be accurately measured.

Jan 1, 1936

By L. J. Health

Synthetic rock with predictable porosity and permeability has been Prepared from mixtures of sand, cement and water. Three series of mixes were investigated primarily for the relation between porosity and permeability for certain grain sizes and proportions. Synthetic rock prepared of 65 per cent large grains, 27 per cent small grains and 8 per cent Portland cement, gave measurable results ranging in porosity from 22.5 to 40 per cent and in permeability from 0.1 darcies to 6 darcies. This variation in porosity and permeability was caused by varying the amount of blending water. Drainage-cycle relative permeability characteristics of the synthetic rock were similar to those of natural reservoir rock. INTRODUCTION The fundamental behavior characteristics of fluids flowing through porous media have been described in the literature. Practical application of these flow characteristics to field conditions is too complicated except where assumptions are overly simplified. The use of dimensionally scaled models to simulate oil reservoirs has been described in the literature. 1-3 These and other papers have presented the theoretical and experimental justification for model design. Others have presented elements of model construction and their operation. In most investigations the porous media have consisted of either u ncon soli da ted sand, glass beads, broken glass or plastic-impregnated granular substances—materials in which the flow behavior is not identical to that in natural reservoir rock. The relative permeability curves for unconsoli-dated sands differ from those for consolidated sandstone. The effect of saturation history on relative permeability measurements is discussed by Geffen, et a1.4 Wyga15 has shown quite conclusively that a process of artificial cementation can be used to render un consolidated packs into synthetic sandstones having properties similar to those of natural rock. Many theoretical and experimental studies have been made in attempts to determine the structure and properties of unconsolidated sand, the most notable being by Naar and Wygal.6 Others have theorized and experimented with the fundamental characteristics of reservoir rocks. This study was conducted to determine if some general relationship could be established between the size of sand grains and the porosity and permeability in consolidated binary packs. This paper presents the results obtained by changing some of the factors which affect the porosity and permeability of synthetically prepared sandstone. In addition, drainage relative permeability curves are presented. EXPERIMENTAL PROCEDURE Mixtures of Portland cement with water and aggregate generally are designed to have certain characteristics, but essentially all are planned to be impervious to water or other liquids. Synthetic sandstone simulating oil reservoir rock, however, must be designed to have a given permeability (sometimes several darcies), a porosity which is primarily the effective porosity but quantitatively similar to natural rock, and other characteristics comparable to reservoir rock, such as wettability, pore geometry, tortuosity, etc. Unconsolidated ternary mixtures of spheres gave both a theoretically computed and an experimentally observed minimum porosity of about 25 per cent.7 By using a particle-distribution system, one-size particle packs had reproducible porosities in the reproducible range of 35 to 37 per cent.6 For model reservoir studies of the prototype system, a synthetic rock having a porosity of 25 per cent or less and a permeability of 2 darcies was required. The rock had to be uniform and competent enough to handle. Synthetic sandstone cores were prepared utilizing the technique developed by Wygal.5 Some slight variations in the procedure were incorporated. The sand was sieved through U. S. Standard sieves. A 18-20 sand denotes that the sand passed the Number

Jan 1, 1966

Provide optimum visibility of mining operations while maintaining protection and comfort for ma-chine operators. Approach Cabs and canopies with hydraulically powered variable-height control were developed for several machines and tested in underground mining operations. How It Works From his position in the cab, the operator can raise or lower the cab, selecting a height that offers either more visibility of the working place or greater clearance for tramming. The entire cab enclosure moves up and down on guide rollers that ride on a pair of rails, and is actuated by a hydraulic cylinder controlled from within the cab. Normal working heights, for each of the four different cabs developed, are with the cab bottom from 6 to 8 inches above the mine bottom. A typical range of elevation (excursion) afforded by this design is shown in Figure 1.

Jan 1, 1978

By S. H. Ash

For several years considerable activity has been devoted to economic and social factors affecting California metal-mining operations as they relate to accidents and their cost. The reason for this intense interest is that accidents cost this industry annually over $1100,000 in industrial insurance premiums for mines insured by insurance carriers only; during 1924-32, inclusive, they amounted to $3,616,9115. There are several reasons for this high cost, the most important of w rich are the consistently .high frequency and severity rates of injuries occurring in the industry. Coordination of effort, appreciation of a mutual problem, and widespread education are essential if accidents and their cost are to be reduced.

Jan 1, 1935

By Jennings S. Cox

(Glen Summit Meeting, June, 1911.) THE following notes, prepared in 1908, as the result of a personal examination and extensive explorations under my direction in 1906, have been revised and greatly augmented after two subsequent visits and further explorations in 191.0. The hard iron-ores of the south coast of Oriente Province, in the island of Cuba, have been known for many years, in fact one mine has been in operation for more than 20 years ; but it is only within the past four years that the large mantle-deposits of brown ores of the north coast have attracted serious attention. A. C. Spencer 1 has described these ores in a paper, entitled Three Deposits of Iron Ore in Cuba, which refers to the Mayari, Moa, and Cubitas deposits. C. M. Weld,2 in a scholarly paper on The Residual Brown Iron-Ores of Cuba, has discussed the character and possible genesis of these deposits with particular reference to the Moa field, calling attention also to the Taco and Navas fields in addition to those described by Spencer. Descriptive articles with reference to the Mayari field, and a few words about the Moa deposit, have also appeared.3 It is the purpose of the present paper to give some account of the exploration of the Moa deposit and to call attention to its commercial importance. LOCATION. The Moa district is situated on the north coast of the . Province of Oriente, which is the most easterly province of the island of Cuba. It lies on the northern or seaward slope of 1 Bulletin No. 340, U. S. Geological Survey, pp. 318 to 329 (1908). 2 Trans., xl., 299 to 312 (1910). 3 Iron Age, vol. lxxx., No. 7, pp. 421 to 426 (Aug. 15, 1907), and vol. lxxxi., No. 15, pp. 1149 to 1157 (April 9, 1908).

Mar 1, 1911

Council and Standing Committees - 1982/83 President: Prof. A. N. Brown Vice Presidents: Prof. R. P. King and J. D. Austin Honorary Treasurer: Prof. D. G. Krige Immediate Past President: G. Y. Nisbet Members of Council: B. C. Alberts, R. H. English, P. T. Fewell, C. E. Fivaz, J. S. Freer, Prof. G. G. Garrett, J. J. Geldenhuys, Dr A. K. Haines, P. N. Harris, H. E. James, Dr B. K. Loveday, Dr J. Lurie, D. G. Malan, G. Pienaar, B. E. Protheroe, Dr 0. K. H. Steffen, G. C. Thompson, Dr H. Wagner, Dr P. T. Wedepohl. Chairman, Witbank/Middelburg Branch: H. C. van Zyl.

Jan 1, 1983

By Richard N. Zimmer

This paper discusses the installation of corrugated steel linings in bored raises at Inco's Thompson Mine. The procedure for the installation of these linings is outlined and the relative advantages are compared with conventional methods of ground support. Future trends in the use of corrugated steel products are then discussed.

Jan 1, 1978

By X. H. Zhang, J. G. Cai

This paper discusses the behaviour of large-span tunnels and caverns in hard rock in a major underground storage project. In-situ stresses were measured using hydraulic fracturing during site investigation and 3-D overcoring during construction, with both showing a horizontal stress ratio of 2-3 times the vertical stress. Rock reinforcement design was based on the Q-system combined with numerical modelling for special design cases. Tunnel design and performance were checked and monitored by in-situ instrumentation during rock excavation, including measurements of deformation, convergence, and load on rock bolts. Deformation measurements using borehole extensometers included one borehole drilled into the virgin rock before rock excavation, which provided a direct and very insightful comparison with the various deformation measurements made during rock excavation. These measurements coupled with numerical calculations have proven that the high horizontal stresses to be very favourable to the stability of the large openings.

Jan 1, 2003

By K. A. Natarajan

Interaction with microorganisms results in significant surface chemical changes on minerals. For example, chemolithotrophs such as Thiobacillus ferrooxidans and Thiobacillus thiooxidans significantly alter the surface chemistry of several sulfide minerals such as pyrite, chalcopyrite, sphalerite and galena. Heterotrophic bacteria such as Bacillus sp. could alter the electrokinetic properties of oxide minerals such as hematite, alumina, silica, kaolinite and calcite. Microbe-mineral interactions could thus be beneficially utilised in mineral beneficiation as different from bioleaching. Microbially induced mineral beneficiation unlike bioleaching deals with interfacial phenomena at mineral-solution-bacteria interfaces and surface chemical changes are brought about at very rapid rates amounting to a few minutes resulting in mineral separations in an aqueous medium.

Jan 1, 2003

By Francesco Vegliò, Luigi Toro, Francesca Beolchini, Francesca Pagnanelli, Stefano Ubaldini

"Biosorption is an innovative technology used to remove heavy metals from aqueous solutions from mining waters and other industrial wastes. A wider application of this alternative process is strictly dependent on the understanding of the chemico-physical aspects involved, in order to optimize the operating conditions. Mechanistic models are the most useful tools used for understanding purposes, even if the empirical models are still widely applied for their simplicity.In this paper especially propagated biomasses of Sphaerotilus natans, calcium alginate and some waste materials were tested as adsorbents for single and binary solutions containing heavy metals at different pH. The equilibrium experimental results were fitted according to empirical and physical models with growing complexity outlining the inadequacy of the predictive models; in fact, the non-ideal interactions among metals require the insertion of additional correction parameters."

Jan 1, 2003

By S. Hunt, D. de Vries

Kansanshi Copper Smelter began operation in March 2015. The smelter features a single Isasmelt furnace for smelting, one 6-in-line electric furnace for matte-settling and slag-cleaning duties, four Peirce- Smith converters and two rotary anode furnaces. A 1,450 t/day oxygen plant and a 4,085 t/day sulphuric acid plant are included in the smelter operations. This paper gives an overview of the operational performance to date with summary data for each smelter section. Challenges such as an unforeseen refractory failure in the Isasmelt furnace in 2016 are discussed. Design improvements around the electric furnace are mentioned. Plans for potential future improvements are put into context. A consistent focus on operations, maintenance and continuous improvement has seen the smelter easily achieve its nameplate capacity of 1.2 million tonnes per annum of copper concentrate throughput. The smelter now operates consistently at a concentrate throughput rate of 1.38 million tonnes per annum of copper concentrate. INTRODUCTION The smelter was commissioned in March 2015. Design and commissioning of the smelter have been discussed by de Vries, Hunt, Hanschar and Louie (2016). The smelter rapidly ramped up to achieve nameplate production (1.2 million tonnes per year concentrate) and in 2018 operated consistently at the rate of 1.38 million tonnes per year concentrate. This paper presents major operational data for each section of the plant and describes significant events and improvements during the first four years of operation. The smelter flowsheet is shown in Figure 1.

Jan 1, 2019