Search Documents

By David C. Oyler, Dennis R. Dolinar, Christopher Mark, Craig S. Compton

Fully-grouted roof bolts comprise more than 80% of the primary roof supports used in U.S. coal mines. However, nearly 1,500 MSHA reportable, non-injury roof falls occur each year, and most of these are attributable to failure of the roof bolt system. Anchorage failure is one failure mechanism for fully-grouted bolts. As roof deformation works its way upward, the bolts can become heavily loaded near their upper ends. If the applied load exceeds the anchorage, the bolts will simply pull out. Research dating back 30 yrs indicates that this type of anchorage failure is most likely when the roof rock is weak, just where roof support is most critical. In soft shale or coal roof, the small amount of data available in the literature indicates that 20-30 in of resin anchorage may be required to achieve the full capacity of the bolt. In other words, the “full resistance zone” of a 60 in bolt may actually be just 30-40 in. Despite its potential importance, there is no widely accepted anchorage test for fully grouted bolts. Standard pull tests have sometimes been employed, but they provide no information on the anchorage near the top of the bolt. An alternative, first described more than 25 yrs ago in the U.S., is the short-encapsulation pull test (SEPT). With this test, the bolt is installed with only a short (1 ft or less) tube of resin. In recent years variations of this test have become international standards. v

The general nature of the special constructional features that are required to provide safety from explosion hazards on machines approved as permissible by the Bureau of Mines is fairly well known to mining men who are at all interested in safety. These requirements are outlined in the schedules under the provisions of which the investigations of such machines are conducted. Also, the method of conducting inspections and tests of such machines has been described in Bureau of Mines Bulletin 305, Inspection and Testing of Mine Type Electrical Equipment for Permissibility, published in 1929. A more detailed knowledge of the special safety features of a particular machine is often useful and sometimes essential for inspectors, safety engineers, maintenance men, and engineers in selecting machines for a particular application. Three bulletins that give information of this nature have been-published by the bureau, viz., Bulletin 313, Permissible Storage-Battery Locomotives and Power Trucks. Bulletin 343, Permissible Coal-Handling Equipment. Bulletin 382, Permissible Coal-Cutting Equipment. Report of Investigations 3309, Permissible Electrically Operated Air Compressors, which contains similar information, was issued in August 1936, and a Report of Investigations 3326, Permissible Electrically Operated Room Hoists, was issued in January 1937. Thus, the present paper is the third to give detailed information concerning permissible machines of types not included in bulletins, and covers all the rock-dust distributors approved prior to October 1, 1936.

Jan 1, 1937

By R. J. Stokes

S. Floreen (international Nickel Co.)— One fairly simple way to differentiate between em brittle me nt due to surface microcracks or due to a dislocation barrier effect might be to load a brittle rock salt crystal in tension to some stress just below the fracture stress and then immerse the loaded crystal in water. If a surface film is retarding plastic flow then one should observe some plastic deformation of the rock salt as

Jan 1, 1962

Beatrix Gold Mine, a deep-level gold mine in the Free State province of South Africa, has the highest methane emission rate of any gold mine in the country. Methane is emitted from underground sources intersected during mining operations and is liberated into the general mine atmosphere. The total methane emission rate for the mine is of the order of 16001/s and the South section of the mine emits approximately 10001/s of methane gas. The mine has a history of gas accumulations which have led to a number of underground explosions. Following the last explosion in 2001 and the subsequent investigation, a number of recommendations were made. Two of these were to consider extracting the underground mine methane to render the mine atmosphere safe, and to declare hazardous locations that require special operating procedures. A number of such workplaces have now been declared at the South section of the mine. Methane gas is a potent, explosive greenhouse gas whose contribution to global warming and climate change is 21 times higher than that of carbon dioxide. To reduce its inherent danger and to mitigate its global warming impact, a carbon credit project under the Clean Development Mechanism (CDM) of the Kyoto Protocol has been developed and implemented, the aim being to capture and destroy the methane at Beatrix mine. The mine has constructed an extraction system to capture and extract 400 (Is of the methane. Percentage methane (per volume) of the gas intersected at source is 85%, with negligible concentrations of other hydrocarbons and water associated. The mine contracted the services of Group Five to design and construct the flare and ancillary equipment on surface, and Promethium Carbon was contracted to assist with the carbon¬-related aspects, approval framework, and administration of the project. A number of design and construction challenges had to be faced to extract and transport the gas effectively to the surface of the mine as the emitters are approximately 3 600 m away from the mine shaft at a depth of 860 m. Further considerations were the requirements for the type of column to be used to transport the methane gas, the pressure loss over the system, the safety systems needed to address the risk factors involved in the transport of the methane gas, and a suitable pumping system to extract the gas to the surface. The system operates under negative pressure provided by two blowers on surface delivering the emissions to a flare capable of burning off 450 8/s of methane gas. In this paper a number of benefits for the mine are discussed. These include, but are not limited to, the removal of approximately 55% of the total volume of methane gas from the general body of the air in the geographical areas of the mine where the methane gas is emitted into the atmosphere, and reducing the risk of methane-related incidents. A further benefit of this project is the mitigation of the global warming impact of the methane gas and the reduction of the mine's carbon footprint by approximately 25%. This project could also assist in alleviating the energy shortage being experienced in South Africa by means of the planned generation of 4 MW of electrical power, utilizing the methane gas, as a second phase of the project.

Jan 1, 2011

By D. Bois, P. Keating, J. Lemieux, M. A. Vallée, M. Allard, R. S. Smith, L. Z. Cheng, M. Chouteau, D. K. Fountain

"As part of a larger research program, a number of MEGATEM airborne electromagnetic (EM) test flights were flown over the Gallen massive sulfide deposit in northwest Québec. A particularity of this test site is that a major part of the ore body was extracted before the MEGATEM survey. Therefore one of the purposes of this study was to verify the ability of the system to detect the remaining massive sulfides below the water in the open pit. The open pit is also surrounded by a metallic fence, and a power line is present in the vicinity. A large part of the case study involved accounting for the impact of infrastructure and acidic water on the survey, which will help in the interpretation of airborne EM responses in complex exploration situations.The Gallen deposit was also previously flown with the INPUT and GEOTEM airborne EM systems before the major exploitation period. A comparison between the results from the different survey results allows estimation of the physical properties of the Gallen deposit, which is a relatively poor conductor.A new method for removing the power line signal shows amplitudes with a smaller residual associated with the emanating fields, and more compact, cleaner responses associated with induced currents. This will make it easier to identify bedrock conductors close to power lines"

Jan 1, 2007

By H. W. Fleming, R. R. Brooks

The Clearwater Deposit, a small occurrence of massive-sulphide mineralization enclosed in an envelope of disseminated-sulphide mineralization, was discovered as a result of an aeroelectromagnetic survey in New Brunswick in 1955. Subsequently, additional flights were made over the deposit and various ground follow-up methods were employed to ascertain the nature of their response. All methods proved to be capable of indicating the occurrence with varying degrees of precision. This paper is a presentation and a discussion of the magnetic and electromagnetic data, both airborne and ground, and the self-potential data obtained over this deposit. The attention of Canadian mining exploration companies was initially focussed on New Brunswick by the discovery, in 1953, of the Brunswick ore body. Ground electromagnetic surveys were of considerable assistance in locating and developing this deposit. In the following year, 1954, the Heath Steele base-metal deposits were discovered by employing an airborne electromagnetic device and ground electromagnetic surveys to follow-up the airborne indications. These discoveries demonstrated clearly that both airborne and ground electromagnetic techniques were applicable for locating the near-surface deposits of massive sulphides present in this region. Airborne electromagnetic equipment became available on a contract basis through Aeromagnetic Surveys Limited early in 1955 and was used extensively thereafter throughout a large portion of northern New Brunswick. It was as a result of one of these surveys with Aeromagnetic Surveys Limited equipment in the summer of 1955 that the Clearwater Deposit was detected. The airborne anomaly was located on the ground by means of an electromagnetic survey using a Swedish Slingram unit. During 1956, the region was investigated more thoroughly- in the hope that other sulphide bodies might be located. Airborne electromagnetic coverage was extended and the Clearwater Deposit itself was used as a testing ground for the various methods and types of equipment currently in use in New Brunswick. In this paper com prative data are presented for the airborne magnetic, airborne electromagnetic, ground magnetic and ground electromagnetic surveys over this deposit. The ground electromagnetic instruments used were the McPhar vertical-loop unit and the Slingram and Boliden horizontal-loop units. Self-potential surveys were carried out with a McPhar unit. From the geophysical point of view, all ground electrical methods employed indicated the presence and the extent of the massive-sulphide mineralization with a good degree of accuracy. The horizontal-loop methods however, defined the contacts more precisely as is to be expected when dealing with a flatly-dipping

Jan 1, 1961

By J. B. Fletcher

The Miami mine first started operations in 1910. For convenience, the history of the orebody can be divided into the following categories (Fig. 1): 1) 1910 to 1925: 24.4 million tons of high grade ore, mined by top slicing, sublevel caving, etc. 2) 1926 to 1954: 102 million tons of low grade ore, mined by block caving.

Jan 1, 1961

By Karl Oltay

A series of 15, stations beginning with Potsdam and Budapest and ending with Budapest and Potsdam were occupied inn the period August, 1908, to January, 1909. The intermediate stations were all at points which had been connected by Baron Eötvös with torsion-balance traverses. The observations were made with an invariable pendulum of the standard four-pendulum type of instrument of the Geodetic Institute, made by Stückrath at Berlin-Friedenau. The observations at each of the field stations lasted-one to three days with one exception; two or three time determinations were made; four to eight series of pendulum observations were made; the error of determination of the elevation of the instrument above mean sea level ranged from 0.30 meter to 1.10 meters, with the exception of the Arad and Baja stations, where the elevation was known more accurately and averaged about ± 0.8 m, which would cause an error of ± 0.25 x 10-3 dynes. No topographic correction was applied. The values for ?g were taken from Eötvös: Report on Geodetic Observations in Hungary, especially Observations with the Torsion Balance, Budapest, 1910. The differences in ?g as determined, by the torsion balance and by the unvariable pendulum were: Kuvin-Hidegkut 1.2 km. 0.001, Livada-Kuvin 9 km. 0.001, Pankota-Livada 13 km. 0.004, Kuvin-Arad 20 km. 0.000, Pankota-Arad via Kuvin 42 42 km.0.005, Pankota- Arad via Kurtics 50 km.0.000 dynes. Oltay concludes that if the stations are close enough together and if the terrane is rather flat, the measurement of ?g with the Eötvös torsion balance is as accurate as with the invariable pendulum. -- Donald C. Barton.

Jan 1, 1929

By Glenn L. Allen

The rapid rise of industrial Los Angeles to international prominence has been accompanied by the natural corollary - a record influx of population - together with greatly increased production and fabrication of steel and nonferrous and light metals; industrial mineral processing; and high consumption of fuel oil, gasoline, and chemicals. These have resulted in the release of hundreds of tons of metallurgical and mineral dusts, fumes, and gases into the atmosphere daily. Los Angeles County, intrinsically, is no worse than other industrial centers in respect to the generation of atmospheric contamination. It is, in fact, more fortunate in that no coal is used, and it has no great primary metallurgical industries comparable to those of Chicago and Pittsburgh. Meteorologic and topographic peculiarities of the area, however, which result in poor drainage of the polluted air away from the Los Angeles Basin, serve periodically to greatly increase the intensity and frequency of industrial smog visitations. This combination of intense industrialization, population influx, climate, and topography has made mandatory control of air pollution necessary. The nonferrous pyrometallurgical industry of Los Angeles has three rather unusual characteristics that contribute to its difficulties in developing suitable fume control: It consists of a multiplicity of relatively small establishments subject to wide Variations in products and operating schedules; operations are largely of the secondary or reclaiming nature and, therefore, often work dirty scrap metals; and, unfortunately, much of the industry is concentrated, to a considerable extent, near the center of the city. A difficulty inherent in most nonferrous foundries, including the many brass-works melting alloys containing zinc, is the high volatility of zinc and the extremely small mean particle size of the resulting zinc oxide fume.

Jan 1, 1952

By J. B. Dyess

TARNISH films on some of the common metals (particularly on copper and silver) have been of much scientific and commercial concern for a long time, but before the development of the electrical method1 of measuring film thicknesses there was no satisfactory quantitative approach by which to study the separate parts of these complex films. This method has been adapted to the measurement of duplex (cuprous-cupric) oxide films on copper .2 In the present work it has been used to measure tarnish films on copper when they were mixtures of cuprous oxide and cuprous sulphide, and also when they contained cuprous oxide, cupric oxide and cuprous sulphide, each component part being measured at a different potential value. Oxide-coated copper specimens, prepared by heating copper in air at chosen temperatures for given periods, were exposed to moist hydrogen. sulphide in air to form the various oxide-sulphide films studied. The comparative resistances afforded by (1) different thicknesses of oxide films, and also (2) equal thicknesses of oxide and sulphide films, against severe attacks of hydrogen sulphide were measured. The electrical method requires that the time be observed for the cathodic reduction of each part of the film substance, and these respective time values multiplied by the constant current give the corresponding quantities of electricity expended. Then each millicoulomb per square centimeter represents a film thickness of T= MX10 8 2D X 96,494 X 103 (a) where M is weight of oxide (or sulphide) giving one gram-atom of oxygen (or sulphur) for cathodic reduction, D is density of the oxide (or sulphide) and t is the thickness in Angström units per millicoulomb per square centimeter. The value of t for cuprous sulphide (cubical) is 14.27, and is obtained by substituting 5.78 for D and 159.20 for M in equation a. Previous values2 of t for cuprous and cupric oxides (12.36 and 6.39, respectively) were used in the present work.

Jan 1, 1939

By N. Hiroyoshi, R. D. Corpuz, M. Ito, Hokkaido University, C. B. Tabelin, S. Veerawattananun

"Acid mine drainage (AMD), the very acidic and heavy metal-contaminated leachate generated when pyrite-bearing rocks are exposed to surface oxidizing conditions, is a serious environmental problem encountered after the closure of mines and mineral processing operations. In this study, we investigated the effects of soluble phases and metallic oxides, which are commonly found in strongly weathered pyritic wastes, on pyrite oxidation. Strongly weathered pyrite containing melanterite (FeSO4·7H2O) as the main soluble phase was obtained from Furikusa mine, Japan. The sample was washed using two methods to vary the relative amounts of melanterite in the sample. The effect of metallic oxides on pyrite oxidation was evaluated using ultrapure hematite suspensions. Our results showed that under acidic conditions, the effect of soluble salts on the oxidation of pyrite was stronger than hematite. More thorough washing of the sample resulted in the formation of an arsenic-bearing iron-oxyhydroxysulfate coating that minimized pyrite dissolution. This oxidized layer became relatively thicker and mechanically stronger when hematite was introduced after the more thorough removal of soluble salts. Characterization of this “coating” coupled with geochemical modeling suggest that it is most probably composed of two materials: schwertmannite and scorodite. Based on these results, a new approach to suppress pyrite oxidation by directly using iron-oxyhydroxysulfate as coating material is introduced.INTRODUCTION Acid mine drainage (AMD), the very acidic and heavy metals-contaminated leachate produced in closed/abandoned mine sites (Evangelou, 1995), mineral processing and coal cleaning tailings (Evangelou, 1995), and tunnel construction waste rocks (Tabelin and Igarashi, 2009, Tabelin et al., 2012), is one of the oldest and probably the most serious environmental problem of anthropogenic origin. When released to the environment, it rapidly pollutes river, soil and groundwater systems leading to the destruction of affected ecosystems. AMD is produced when pyrite (FeS2), one of the primary gangue minerals in sulfide ores and coals, is exposed to oxidizing conditions as illustrated by the following reactions:"

Jan 1, 2016

By Zengjie Wang

Kinetic study of hydrochloric acid leaching of Panzhihua ilmenite from China is presented. Both temperature and concentration of hydrochloric acid have significant effects on the rate process of Fe dissolution from ilmenite ore, while the ratio of liquid to solid has little effect on the Fe dissolution. The Fe dissolution is found to follow the spherical model f (??) =1-(1- ??)1/3 and the apparent activation energy is calculated as 47.21 KJ/mol, suggesting a chemical reaction controlled mechanism. The dissolving behaviors vary at different kinetic stages. At the beginning the amount of the dissolved Fe and Ti increased monotonically with leaching time, while about 15 minutes later the dissolved Ti in the form of TiOCl2 began hydrolyzed into TiO2 fines reunited on the ilmenite ore surface, as observed by SEM and EDS technique. For the unreacted ilmenite particles covered by a layer of hydrolyzed TiO2, the leaching seemed to be as a selective leaching of iron and because Ti dissolved from and hydrolyzed rapidly again into the unreacted ilmenite particles. The leaching process can be ended 4 hour later when almost of Fe has dissolved into the solution and TiO2 remains as solid residues. The effects of acid concentration and leaching temperature were also investigated.

Jan 1, 2009

By M. Kumral

The efficiency of an ore-processing unit depends on the consistency of the characteristics of raw material entering the plant. When the mined ore is highly variable in quality, the only way to ensure consistency is to homogenize the ore prior to feeding to the processing plant. The homogenization can generally be achieved by the bed blending operation. Given that the stockpiling and reclamation processes are very expensive, it is necessary to design the process in such a way as to minimize variabilities of specified properties of raw material. In this paper, for alternative stacking types, optimal stockpile geometry is found in three stages: First, stockpile input is simulated by sequential Gaussian simulation, and then the variance reduction ratios (VRR) as a criterion of stockpile efficiency are calculated for various stockpile geometry scenarios by a stockpile simulator written in FORTRAN. Second, multiple regression analysis is performed to model the VRR by the use of stockpile length, the number of layers and stacker speed as the independent variables. Finally, the model is an optimization problem. Decision variables are the stockpile length, the number of layers, stacker speed and stacking type. The genetic algorithms (GA) are used to minimize the VRR. The approach was demonstrated on data from an iron orebody. The problem was to reduce fluctuations of iron, silica, alumina and lime contents in the stockpile output. The results showed that the approach could be used for the bed blending design efficiently. Keywords: bed blending design, multiple regression analysis, genetic algorithms, iron ore, content fluctuation

Jan 1, 2006

By Z. J. Fink

Ultraviolet-visible and infrared emission spectra from propagating methane-coal-dust-inhibitor mixtures have been obtained in a 0.2-by 0.2¬by 5.3-m vertical duct over a range of flame speeds from 2 to 100 m/sec. Results serve as a basis for the design and evaluation of thermal radiation detectors for triggered barriers that suppress ongoing mine explosions. Of particular significance is the large continua superimposed on the methane-air spectra when small amounts of coal dust are present and the variation of emissivity with infrared (IR) wavelength in dust flames. In conjunction with the spectral measurements, studies of flame speed, particle size, gas sampling plus thermodynamics, and dust sampling are presented and discussed in order to gain insight into the more fundamental aspects of propagating explosions. Sampling results have shown that only a near-stoichiometric amount of dust is consumed in the flames studied even though initial concentrations are five times stoichiometric. Difficulty in propagating coal-dust inhibitor flames of realistic mine characteristics in a cold-walled laboratory duct has been encountered. A simplified analysis of the flame zone utilizing spectral and sampling results indicates that the stability of slowly propagating flames is more dependent upon thermal radiation than upon convection losses to the walls. It is predicted that thermal radiation losses will make any measurements of coal dust burning velocities, "quenching diameters," or flammability limits more apparatus dependent than those corresponding to gaseous fuels.

Jan 1, 1974

By J. A. Finch, A. R. Laplante, R. Espinosa-Gomez

"The Niobec concentrator rejects up to /5% of the Nb as slimes (-10u.m). The recovery of Nb from these slimes by column flotation is being studied. An essential condition for selective flotation is slimes dispersion. A particle size analyzer, the Sedigraph 5000D, was used to monitor dispersion in plant waters with combinations of organic and inorganic dispersants and flotation reagents. Flotation reagents were particularly detrimental to dispersion with sodium silicate. The best dispersion conditions were selected for column flotation tests. These tests revealed that reagent combination had a pronounced effect on froth stability. Careful frother selection achieved good froth stability under conditions of good dispersion. Plant water increased the required dispersant concentration causing mineral depression.IntroductionSlimes (-10 u.m) rejected at Niobec contain up to 15070 of the over-all Nb content . Recovery of Nb from these slimes would significantly increase over-all recovery. A suggested recovery route involves two phases: (1) carbonate flotation (to remove most of the carbonates) depressing silicates and pyrochlore (as currently done at Niobec); and (2) selective (direct) pyrochlore flotation from the silicates. Phase 2 has been addressed and several routes to achieve selective flotation are available. Phase I was attempted with the selective reagent scheme used at Niobec but a considerable amount of pyrochlore floated with the carbonates due to poor slimes dispersion."

Jan 1, 1987

By Moussa Wone

The Washington, DC Water and Sewer Authority (WASA) has implemented facility planning for the Anacostia River Projects portion of a program to bring its Combined Sewer System (CSO) into compliance with federal water quality regulations by 2025. The program includes approximately 19 kilometers (12 miles) of deep CSO storage/conveyance and flood relief soft ground tunnels, construction, vortex drop, overflow, maintenance and air release shafts, as well as near surface diversion structures and conveyances. The Project encompasses major technical and non-technical challenges including completion under a federal consent decree schedule, construction within the confines of heavily developed urban areas, difficult ground conditions, major infrastructure crossings, and close coordination with several major public agencies. This paper discusses the planning stage considerations related to the geotechnical investigation program, discusses obstructions that influenced alignment selection, and provides two examples of preliminary estimates of settlement induced ground movement due to the tunnel and shaft construction.

Jan 1, 2008

By David Chapman, Glen Frank

Due to the transport mechanics of the depositional environment, glacial soils display a very wide range of grain sizes and behavior. Several nonstandard drilling, sampling, and analytical techniques are therefore required to characterize the subsurface. The paper summarizes the geotechnical investigation for the design of a large project in glacial geology, which will include both large and small diameter pressure balance tunneling. The paper focuses on the challenges presented by the glacial environment and the techniques required to identify and characterize it for design and contract document preparation.

Jan 1, 2001

By K. E. Kolm, W. H. Langer

Developing natural aggregate resources (sand, gravel, and stone) creates environmental impacts. A systems analysis method has been designed to characterize the components of the environmental system, identify potential impacts to those systems, and evaluate the extent of those impacts. The step-wise method consists of problem definition, data collection, preliminary conceptualization and characterization, additional data collection, data analysis, and refinement. The method requires analyzes of various systems making up the environment, including land surface, geomorphic, subsurface, and groundwater systems. After system characterization is complete, the method focuses on identifying and evaluating potential environmental impacts to determine acceptable mining strategies.

Jan 1, 2001

By Du Sichen, K. Mukai, S. Seetharaman

Viscosities of slags constitute an important physical property needed for an understanding of the mass transfer phenomena in metallurgical processes. Viscosity is also the key that leads to a better understanding of the structure of slags. It is well known that the viscosities of silicate slags decrease with the addition of basic oxides due to the breaking of the silicate network. The measurements of slag viscosities often pose experimental challenges, especially to the choice of materials. The keynote lecture takes up the experimental problems and the various techniques adopted. Dynamic viscosity measurement, as a powerful tool towards an understanding of the kinetics of some high temperature reactions, is brought out. A number of semi-empirical models have been developed to estimate the slag viscosities in the case of multi component slags. A critical survey of these models is presented in the lecture. Earlier models by Riboud et al., Urbain et al. and Mills et al. have been developed further into a new generation of models. Some of the current important models are (1) Model by Iida et al. (2)CSIRO model (3) Pyro research Model (4) Model by Tanaka et al. (5) Model approach by Reddy et al. and (6) KTH-model. The predictions and capabilities of the various models are compared. Estimations of viscosities from thermodynamic data and prediction of liquidus temperatures from viscosities are presented. The concept of surface viscosities with reference to slags and viscosities of two-phase mixtures are also taken up in the presentation.

Jan 1, 2004

The compliance sampling method for coal mine dust in the United States has not changed appreciably in the last 30 years. A call for more frequent sampling with immediately available results is leading to new instruments that may supplement or replace the existing sampler. This report discusses two such instruments that provide immediate results of dust levels. The first, called the Respirable Dust Dosimeter (RDD), is designed to supplement the existing U. S. cyclone compliance sampling method. It uses the pressure drop across a filter to provide an inexpensive screening type of measurement. The RDD has been tested in the laboratory and a limited number of coal mines. Side by side testing has compared the RDD performance with personal coal mine samplers in triplicate area sample measurements. Results show that the differential pressure of specific filtration media can be an effective surrogate for respirable mass. Data show that there is a dependence on coal type and an effect of relative humidity. There also appear to be two distinct responses related to coal type. For specific coals the coefficients of determination, R2, are better than 0.9. For general use the detector tube, using laboratory generated calibration curves, can be used to estimate respirable dust levels. However, a calibration to a specific coal type may substantially improve the accuracy. Another sampler in development is called the Personal Dust Monitor (PDM). Designed to give compliance quality accuracy, the PDM uses the frequency change of a vibrating element to measure dust and give immediate feedback of results. Results of laboratory comparison of the prototype PDM sampler to personal gravimetric samplers indicate R2 values of better than 0.99 for three different coal types. Work is in progress to package the components into a person-wearable unit combined with a cap lamp system with a total projected weight of less than 1.4 kg (3 lbs).