Search Documents

By Helge Rosenberg

Up to now, Topsøe WSA (Wet gas Sulphuric Acid) plants have been in operation for almost 30 years, and close to 80 plants have been sold. In spite of its unique features and ability to treat gases without any prior drying, the WSA technology has had certain restrictions with regards to SO2 concentration in the feed gas, and the overall conversion of SO2 by catalytic means has been limited to approx. 99.7%. In commercial scale sulphuric acid production on the basis of elemental sulphur and metallurgical off-gases, there is a demand for higher SO2 conversion and treatment of gases with a higher content of SO2. Therefore Topsoe has further developed its WSA technology to cope with these demands. This paper will explain more about the principles of such new development and leave the delegate with a better understanding of the potentials of the new generation of the WSA technology from Topsoe.

Jan 1, 2009

By Mackenzie Burnett

This program was initiated by USBM to quantify the respirable dust problem caused by the use .of roadheaders in underground metal/nonmetal mines with special emphasis on this problem in uranium mines. The contract called for the development of methods or equipment to alleviate the respirable dust and to implement the solution in a mine. Attempts to quantify the dust problem were made in the following way: survey of MSHA records, survey of state mine enforcement agencies, survey of mine records, dust measurements taken at two mines using roadheaders. The results of this study are not conclusive due to very limited and sometimes less than useful data; however, the study does indicate that a serious dust problem could and may exist. If and when roadheader use becomes more popular, it is almost certain that development of dust control procedures and equipment will be necessary. This contract was concluded without developing this equipment since only one roadheader is currently in use in an American uranium mine and the mine prefers not to participate in the program at this time. This report discusses the available data concerning respirable dust problems and presents a solution which can potentially help to solve the problem. The solution requires the use of blowing ventilation, on-board dust extraction at the source, and filtration, as well as continued use of water sprays. The on-site tuning of such a system is necessary to demonstrate the degree of improvement possible.

Jan 1, 1981

OWING to the gradual depletion of the hitherto plentiful supply of firewood in the immediate vieinity of Queenstown and Gormanston, which caused a steady increase in the cost of fuel for domestic purposes, the Mount Lyell Company took steps several years ago to make available as a substitute electric current from its Lake Margaret hydro-electric supply. In order to make this practicable it was necessary that the cost of electric power for heating purposes should compare favourably with the cost, of fuel, and the installation of domestic appliances brought within reach of the average householder, and efforts have been continuously directed towards this end since the year 1928.WATER HEATERSThe installation of electrical apparatus in local dwellings began with hot-water services, the heating elements being the types then procurable on the market and adapted to meet requirements.These, however, did not prove satisfactory, but the study of their bilure resulted in a type being developed locally which has overcome all difficulties. The first type of water heater evolved was an outside circulation one the element of which consisted of an iron pipe through which the water passed, insulated with micanite and wound with nichrome wire, the latter being covered with alundun cement to keep it in position and prevent oxidation. This was insulated on its outside surface with a layer of asbestos flour, and connected to the hot-water container as shown in Fig. 1. It was found, however, that the iron pipe had a short life, due to a certain amount of acidity in the water, and a copper pipe was substituted which proved very durable. Some heaters with this improved type of element are still operating after six years of use. The resistance wire is run at a very low current density, which ensures durability.

Jan 1, 1927

By D J. Woodward, A B. Christie, S A. Henrys

Low-level aeromagnetic data available in digital form have been combined to produce a new 1:100 000 scale map of total force anomalies of the Coromandel region, New Zealand. The map incorporates data from 13 surveys flown between 1977 and 1990 and shows the regional magnetic pattern as well as more detailed localised anomalies. In addition to magnetic anomalies, the map also depicts data to aid interpretation, including small-scale maps of topography, geology, magnetic intensity gradient and apparent magnetisation. The primary magnetic anomalies of the Coromandel region are associated with Late Miocene and Pliocene volcanic rocks, but have been locally modified by intense hydrothermal alteration caused by geothermal activity. Epithermal gold-silver and porphyry copper deposits are associated with zones of hydrothermal alteration. The map of magnetic anomalies can be used as an aid to mineral exploration and the interpretation of the processes that control the distribution of mineral deposits in the region.

Jan 1, 2001

By G. Thom, A. Kay, J. B. Hyde

"This paper will initially outline the specific types of copper castings used in blast furnace iron production. Tuyeres, tuyere coolers and stack cooling plates will be discussed in some depth, with particular reference to their dimensional configuration and purpose.Following this, the failure of such cooling members will be discussed, with special focus on tuyeres. Tuyeres are the most common casting which often requires replacement. Reasons for failure and its effect on operations will also be included.The latter sections of the paper will deal with the strict specifications demanded by ironmakers regarding copper castings. The justification for such rigid demands will be explained through the material presented earlier in the paper.IntroductionThe modern 5000-tpd blast furnace, worth millions, is a large capital investment to be sitting idle. Consequently, ironmakers strive to minimize the loss in iron production and revenue from furnace downtime. Two major causes of downtime are furnace relines and shutdowns to replace damaged tuyeresor tuyere coolers. Copper ancillaries are important items in the production of iron. They are consumable items, therefore they contribute to the campaign life or to the downtime in blast furnace production.Several combinations of lining and cooling systems have been used with varying degrees of success. Blast furnace refractories have evolved from ceramic to carbonaceous linings. The Russians and Japanese have successfully introduced stave-cooled furnaces that may have several forms, such as evaporative cooling. Stelco has two furnaces which use the Russian-designed cast iron system. However, this paper will be confined to the use of copper cast cooling members in a conventional internally cooled furnace.Figure 1 is a schematic cross section of the E blast furnace. The three major sections of a blast furnace-the stack, bosh and hearth-are identified. Further, the locations of the various copper members are indicated. This furnace produces an average of 5300 tons of hot metal per day."

Jan 1, 1982

By Joseph T. Singewald

The term "titaniferous magnetite" is used to designate those magnetic ores of iron that carry more than 2 or 3 per cent of titanium. Large and easily workable deposits of these ores occur in different parts of the world, and have attracted attention for many years. Under present furnace practice, however, the smelting of these ores is both difficult and expensive, and for that reason they are not accepted by furnaces, so that the deposits are practically worthless. The problem of finding a feasible method of utilizing these ores has naturally been attractive, and numerous attempts have been made to solve it. Experiments to that end embrace two lines of investigation. The one that has been the more frequently tried is the elimination of the titanium from the ores, so as to make possible their smelting in the usual way. The other is the devising of a method of smelting by which titaniferous ores may be reduced as economically as are non-titaniferous ores. The former method involves a physical process, the latter a chemical process.

Jan 1, 1913

By AIME AIME

The XCVIIth meeting of the Institute for the reading and discussion of papers will be held at Spokane, Wash., beginning Monday, Sept. 27, 1909, as already announced in Special Circulars of May 8 and Aug. 14, 1909, and in the Bulletins for June, July, and August. The meeting will be preceded by a tour through Yellow stone Park and visits to Butte and Anaconda, and will be followed by visits to the Coeur d'Alene district, to the Alaska-Yukon-Pacific Exposition at Seattle, to the mining- and smelting-plants near Salt Lake, and to the iron- and lead- and zinc-plants at Pueblo. The special train for the party' will leave Chicago, September 16, and return about October 12. Details of the itinerary are given later in this announcement. The Secretary of the Spokane Local Committee is Lyndon K. Armstrong, 615 Hyde Block, Spokane, Wash., to whom should be addressed all inquiries concerning local matters. The control of the papers and proceedings will remain in charge of the Institute office, as usual. It is greatly to be desired, both in behalf of the Institute and in recognition of the many courtesies to be extended on the trip, that the excursion party be made larger. Exceptional facilities to visit the many mines and smelters have been freely provided; and members are requested to make all reasonable effort to attend the meeting at Spokane and participate in the excursions. For those who cannot join in the entire trip, it may be possible to provide special Pullman accommodations after leaving Yellowstone Park. In order to make the necessary arrangement, however, the names of members and guests contemplating this partial trip should be sent at once to Theodore Dwight, 29 West 39th Street, New York City. The general cost of the trip per member will be $300, which includes transportation, berth, and meals for the entire trip from

Sep 1, 1909

By Sergio Neves Monteiro

In the present work, a ceramic foam elaborated with illitic clays was characterized. Properties related to density and compression strength were determined in samples fired at 1300oC, a temperature that permits the clay structure to generate and retain gases that will produce the foamy structure. The microstructure of the ceramic foam was studied by X-ray diffraction, scanning electron microscopy and mercury porosimetry. The results showed that the ceramic foam presents a bulk density of 0.38 g/cm3. The microstructure is formed by large open pores, quartz particles and vitreous phase.

Jan 1, 2006

By Zhibao Li, Kunming Zhai, Yan Zhang

The hydration kinetics of MgO, namely magnesia or magnesium oxide, obtained by calcination of magnesite MgCO3 or synthetic MgCO3·3H2O has been studied. Nesquehonite (MgCO3·3H2O) was prepared by the reaction of MgCl2 with Na2CO3 in a mixed-suspension mixed-product removal (MSMPR) crystallizer at 40 °C. Three magnesium oxide samples were obtained by calcination of magnesite MgCO3 or synthetic MgCO3·3H2O in muffle furnace at 900, 1100 and 1300 °C for 3 h, respectively. The hydration experiments of MgO samples were investigated at 25, 35 and 45 °C for 24 h in a stirred batch reactor. The hydration results indicate that the rate and extent of hydration of magnesia decreased remarkably with hydration temperature and increased with decreasing calcination temperature at a constant hydration temperature. The whole hydration reaction of magnesia was supposed to experience the promotive period and declining period. An empirical kinetic model ( k t p -?ln(1-??) ??) and a modification of the classical shrinking core model for diffusion control ( k t b d -?-?3 2 ????1 [1 (1 ??) ] ) have been applied to fit the experimental data of hydration in two stages, respectively. The values of kinetic parameters ( p k and d k ) were obtained by regression analysis and the activation energy of the sample at 900 °C was estimated to be 34.23 kJ/mol. The comparison between MgO from calcination of synthetic MgCO3·3H2O and a commercial MgO used in silicon steel production was carried out, indicating that special silicon steel grade MgO can be obtained by calcination of MgCO3·3H2O below 900 °C.

Jan 1, 2014

The process of hydraulic transport through pipelines, worldwide well known for the transport of fine-grain solids is also being used to a greater extent in mining for the handling of primarily coarse-grain solid û water mixtures for the removal of, for instance û coal and waste mixtures after coal winning using hydraulic monitors, tailings for backfilling underground and washer tailings and flotation waste to the dump. A large-scale test unit was taken into service at the Bergbauforschung GmbH (Mining Research Company) in Essen-Kray, GFR, to further improve this technology. The unit was planned and built by Krupp Industrie- und Stahlbau of Duisburg in cooperation with Bergbauforschung GmbH. The paper deals in detail with the demands made on this test unit and the technical results obtained on it and with the planned experimental research work.

Jan 1, 1980

By A. A. Bakewell

This information circular, which describes mining methods and practices at the Baguio Gold Mining Co., Philippine Islands, is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs. Since January 1952, Baguio Gold Mining Co. has operated its rehabilitated mine and mill in the Baguio district. Postwar labor and supply costs are three or four times prewar costs, whereas ore tenor and tonnage are about the same. Ore reserves remain approximately the same, but deeper and more spreadout operations add to increasing costs. Recently the company has acquired an adjoining property, which may lengthen its life substantially. Costs and general operations are more or less typical of the district, which includes three other active gold mines. Gold ore mined in the district totals approximately 4,300 tons per day.

Jan 1, 1959

By Stewart A. Silling, Dale S. Preece

The two key results of rock blasting are fragmentation and movement of geomaterials. Movement/flow of the blasted rock is often referred to as heave. Modeling the movement of full scale blasting is now possible with 3D distinct element models and parallel processing.

Jan 1, 2016

By W. R. Hardwick

This information circular describes open-pit mining methods and practices of the Bagdad Copper Corp., Yavapai County, Ariz. It is one of a series being prepared by the Federal Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States. A brief history of the Eureka district and of early developments at the [gdad] mine is given, and the are deposit is described with particular emphasis on those characteristics (physical, economic, or engineering) that affected the choice of mining methods. Prospecting, exploration, and sampling and estimating the tonnage and grade are outlined. Development of the open-pit mine is shown. Mining methods, including breaking ground, primary drilling and blasting, secondary drilling and blasting, loading, transportation, engineering, and operating control, are described. A brief summary of mining equipment is given. Percentage of extraction, production rate, mine drainage and water supply, wage, contract, and bonus systems, safety and fire prevention, and the processing plant also are described. The last section gives a breakdown of such costs as are available for publication.

Jan 1, 1959

By William Gleason

"It is the largest mining exhibition in the world that attracts thousands of attendees from around the world to Las Vegas, NV once every four years. Despite the recent struggles in the mining industry, MINExpo International 2016 promises to be as big as ever. In the following pages, Mining Engineering takes a look what some of the more than 1,800 companies plan to showcase during the three-day exhibition.CaterpillarCaterpillar will support MINExpo 2016 with an exhibit showcasing machines, technology, expertise and practical knowledge that miners can apply to help address their cost, productivity and efficiency challenges in today’s mining environment.Caterpillar will once again occupy the largest space at the event and will showcase both surface and underground machines, but the talk at the booth will focus on how Cat technology and know-how combines to help mining operations address and solve the issues that are most important to them. The main stage in the exhibit will feature presentations describing how mining companies, Cat dealers and Caterpillar work together to improve operations.“The challenge for all in the mining industry now is to optimize operations — to drive costs down while creating sustainable businesses that can weather downturns,” said Caterpillar Resource Industries group president Denise Johnson. “We believe that through our expertise and the knowledge of our dealers —combined with innovative technologies and our growing data analysis capabilities — we can help them not only survive, but thrive in these challenging times.” Johnson was selected by the National Mining Association (NMA) to chair MINExpo 2016. “Chairing this show is a great honor, and it’s a testament to Caterpillar’s partnership with this critical industry,” she said. “We’re proud to be a long-time supporter of the NMA, and we are excited to participate in another MINExpo. It’s an opportunity for us all to learn from each other how to increase productivity, control costs and improve overall operations.”Surface mining displays. The surface mining section of the Caterpillar exhibit will showcase the new MD6420C rotary drill. This is autonomy ready and optionally equipped to leverage the safety and productivity benefits of Cat MineStar Terrain. This high-precision drill management system optimizes utilization and improves drilling and blasting operations by accurately guiding the operator and improving precision of hole placement and drilling depth — and the next step is fully autonomous operation, Command for drilling. The third-generation drill incorporates proven Cat components throughout for superior reliability and durability."

Sep 1, 2016

By C. W. Elder

"INTRODUCTION This report describes a method of horizontal drilling in an oil-producing formation underlying a 400-acre, approximately square plot of land in the Franklin Heavy oil field in Sugar Creek Township, Venango County, Pa. The method, which was developed on two previous projects in Ohio, 3/ consists of sinking a shaft to the bottom of a shallow oil sand and drilling holes in a general horizontal plane outward from the chamber in a pattern similar to that of the spokes of a wheel. The project was undertaken by the Venango Development Corporation in an attempt to find an efficient method of recovering oil from partly depleted sand formations.The Venango Development Corporation is composed of the following oil-producing and oil-refining companies and individuals: South Penn Oil Co., Forest Oil Corporation, Kendall Refining Co., Minard Run Oil Co., Quaker State Oil Refining Co., The Pennzoil Co., Alliance Oil Corpo¬ration, United Refining Co., Franklin Creek Refining Corporation, Canfield Oil Co., Pennsylvania Refining Co., Page Oil Co., Freedom Oil Co., D. W. and D. S. Grant, and J. P. Herrick, C. M. Davison and N. V. V. Franchot. Engineering features of the project were supervised by a committee off three engineers A. J. Saxe, chairman, W. M. Shoemaker, and C. N. Pfohl, who supervised the excavation of the shaft and the drilling of the first two holes by alternately spending a week at a. time at the project. The drilling method was under patent license from Leo Ranney, who served as technical advisor to the Venango Development Corporation; in addition, he furnished the design for the shaft and work chamber."

Sep 1, 1944

ST. LOUIS SECTION EUGENE MCAULIFFE, Chairman, J. N. HOUSER, Vice-chairman, VICTOR RAKOWSKY, Vice-chairman., H. G. WASHBURN, Vice-Chairman, W. E. MCCOURT, Sec'y-Treas., Washington University, St. Louis, Mo. H. A. BUEHLER, G. H. COx, L. C. GLENN, E. A. HOLBROOK, W. E. NEWNAM. The eighth meeting of the St. Louis Section was held at the Mercantile Club on Apr. 15, 1918. ,, The meeting was preceded by a dinner, at which 51 members and guests were present, and at which T. T. Brewster presided. Bradley Stoughton, Secretary of the Institute, and Major J. R. Fordyce were the guests of the Section. A number' of the Joplin members were obliged to leave before the close of the dinner, in order to make train connections. The Vice, chairman, therefore, called on Victor Rakowsky, who brought a message of greeting from the Southwest district. At the close of the dinner, the Vice-chairman, T. T. Brewster, introduced Bradley Stoughton, who talked on various subjects of interest to members of the Institute, especially the affiliation of local sections with those of other national engineering societies. The minutes of previous meetings were read and approved-and-the Treasurer presented a financial report covering the previous year.

Jan 6, 1918

By Persifor Frazer

INTRODUCTION For various reasons I have not specified the locality where the research indicated in the following pages was undertaken. It will suffice to say that it was on the grounds of a villa once remote from, but now completely surrounded by, its neighboring city, and in close proximity to an industrial establishment of great extent and importance manufacturing many kinds of steel articles and employing upwards of thirty chimney-stacks for power and process work. The problem was to discover the cause or causes of the mortality to trees and plants on the place, and to trace these causes to their origin. Before undertaking this experimental work, the bibliography accompanying this paper was compiled and studied. It appears from an examination of the careful scientific work performed by the ablest French, German, and English chemists during the last 25 years that they are unanimous in assigning the principal-in fact, the overwhelmingly predominant-cause of the destruction of vegetation to sulphur oxides, resulting either from direct- oxidation of sulphur in oil of vitriol works, etc., or from the oxidation of the sulphur from the minerals associated with commercial coal. Schröder and Schertel showed in 1884 that the sulphates deposited upon the leaves are not injurious to the plants; and Freytag proved that free sulphuric acid could not be found

May 1, 1907

By Martin Herrenknecht

After the successful breakthrough at the end of 2006 of both TBMs into the multifunctional site Faido (MFS), in the middle of 2007 the two tunnel boring machines resumed the 12 km long section between Faido and Sedrun. In the roughly a 10 month interval both approximately 465 m long tunnel boring machines were partly dismantled, pushed through the 2.5 km long MFS, rebuilt for the new larger diameter of 9.5 m and reassembled to be ready for operation. In the rebuilding phase, improvements were made to the equipment, especially as a result of experience gained from the previous 14 km long drive in the section Bodio and taking into account the latest information regarding the upcoming 14 km section Faido. Both TBM drives are currently in the rock formations of the Lucomagno gneiss, which stretch over a section of 3.5 km from the MFS Faido to the predicted Piora Syncline. This section is divided into two fold axes of the Chièra Synform, where the Lucomagno gneiss pass from a sub-horizontal into vertical bedding. The drives, with current rock overburdens exceeding 1,500 m and, as known from the excavation phase of the MFS, in part highly disturbed rock formations, are characterized by the locally intense rock squeezing conditions with large convergences in the vicinity of the driving TBM as well as backwards due to the interaction of the two drives. High expenditure for the support measures, reduced driving performances together with extensive extra work associated with deadlines and increased costs are the result. In the paper the previous experience with the TBM drives in the section Faido and the challenges still awaiting us are presented and discussed.

By H. A. Thorne

This paper describing the mining practices at the Chino mines at Santa Rita, Grant County, N. Mex., is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The Nevada Consolidated Copper Co., Chino mine's, operates an open-cut copper mine at Santa Rita, Central mining district, Grant County, N. Mex. This mine is located about 16 miles east and slightly north of Silver City, the county seat. The ore is-transported in standard railroad cars by the Atchison, Topeka & Santa Fe Railway Co., approximately 10 miles to Hurley where it is milled. The concentrated are shipped approximately l'70 miles over the same railroad to the smelter of the American Smelting and Refining Co., at El Paso, Tex. (fig. 1)

Jan 1, 1931

By Hudson S. B

With a particular electrode configuration, and a particular combination of electrode voltage and roll speed, a relatively small increase in electrode voltage, or a relatively small decrease in roll speed, resultsin a marked improvement in the separation of zircon from ilmenite. In general, fine minerals can be separated using a higher roll speed, or a lower electrode voltage, than is required to separate coarse minerals. The ionizing electrode should be reasonably close to the point at which mineral is fed on to the roll, and nearer to the roll than the non-ionizing electrode. The optimum conditions for the separation of zircon from ilmenite may not apply for the separation of other non-conductors from other conductors.INTRODUCTIONAlthough the high tension separators used in the Australian beach sand industry are efficient, this efficiency has been gained very largely by a process of trial and error, and not by a systematic study of the effects of changes in the operating variables. The optimum roll speed for a particular electrode position and electrode voltage, and the optimum electrode voltage for a particular roll speed and electrode position, can both be determined quite readily. It is not so simple to determine the optimum electrode position for a particular electrode voltage and roll speed. The reason for this is that the electrode used in high tension separators consists of two parts-an ionizing and a non-ionizing electrode respectively. The angular and radial positions of these electrodes, relative to the feed roll and to each other, affect the behaviour of conductors and non-conductors to varying degrees.

Jan 1, 1962