Search Documents

By G. A. Murphy

This tipple differs from the ordinary tipple only in that it embodies numerous refinements for grading and otherwise preparing the coal. Coal from the mines is delivered to the tipple over a surface tram. There are two tracks for loads, which will hold about forty cars, and one track for empties which will hold about the same number. The loads are fed to the dump by gravity from both tracks and are controlled by two squeeze blocks. These blocks are of the type originally designed by Mr. W. J. Elwood, but unlike the original blocks which were of wood and operated by hand levers, are built of steel and operated by com¬pressed air at 100 pounds pressure. They are capable of holding securely twenty-four three-ton cars on a grade of 2.5%. The dump is of the complete revolving type and has a capacity of five cars per minute. After being dumped the empty cars go to the usual kick-back and onto the empty track by gravity. The hopper under the dump has a capacity of approximately fifteen tons, and the coal from this hopper is fed to the shakers by a reciprocating feeder. The screens are of the usual shaker type. They are eight feet wide, seventy-two feet long in two sections, balanced, pitch 12° 30", travel six inches and the eccentric shaft makes 100 revolutions per minute. The upper section of the screen is shorter but heavier than the lower section, and contains the slack and nut screens, consisting of plates with 1 5/8" and 3" round perforations respectively. The lower section contains plates with 4 ½ ", 6" and 8" round perforations respectively, from top to bottom in the order named. The shaker is so arranged that nearly all changes for making the different sizes of coal are made by merely shifting levers. The most complicated change has been made in two and a half minutes; most of the other changes can be made in less than one minute and some of then without stopping the shaker. One of the refinements is what we call the degradation screens. Just before the coal leaves the shaker it goes over a screen with 1 3/8" round perforations, which takes out the fine coal made while the coal is going over the other perforations. This fine coal goes into hoppers and onto the degradation conveyor and to the slack chute. The different sizes of coal, excepting the slack, are delivered by the shaker onto three picking tables. These tables are horizontal for twenty-four feet and then hinged to form the loading booms, so that each picking table forms a unit of continuous conveyor. Centrally located under the picking tables and under the floor, is the refuse conveyor which runs at right angles to the tables. The impurities picked from the coal are dropped into openings in the floor and onto this conveyor, from which they are discharged into a bin of 100 tons capacity. From this bin the refuse is loaded into railroad cars through a gate. The slack may be loaded directly into railroad cars through a chute from the hopper under the shaker, or it may be conveyed to the rescreener. Gates are provided by which all or any part of the slack may be loaded either directly into railroad cars or conveyed to the rescreener. The rescreener is a shaker four feet wide with sixteen feet of plate perforated with 3/4" round holes. The framework is wood, the pitch is 5° and it is driven by eccentrics having a 5 3/4" throw running 143 R.P.M. It is hung on 1"x10" ash boards, rigidly fixed at the support and on the shaker, so that the spring of the boards allows for its movement. The eccentric rods are also of ash, rigidly fixed and spring to allow the movement of the eccentrics. The dust going through this shaker drops into a bin of 80 tons capacity and is loaded into railroad cars

Jan 1, 1925

By Ramana. G. Reddy, Haoxing Yang

The electrodeposition of zinc from zinc oxide using urea and choline chloride mixture in a molar ratio 2:1 is investigated in different experimental variables, namely, the concentration of added [BMIM]HSO4, temperature, and applied cell voltage. The additive, [BMIM]HSO4, was determined to have beneficial effect on the current efficiency, energy consumed in the process and surface morphology of the deposits. The highest current efficiency (92.6%) and lowest energy consumption (2.92kWh/kg) was obtained for solution with 20mg/mL [BMIM]HSO4. The morphology showed the formation of absorbed additive layer on the cathode at higher concentration of additives. Experiments were conducted at different temperatures between 343K and 388K and at various applied cell voltages between 2.7V to 3.6V to determine the best experimental conditions. By varying temperature, highest current efficiency (91.3%) and lowest energy consumption (2.69 kWh/kg) was obtained at 373K. The electrodeposition process is enhanced between the applied voltage 3.0-3.3V by achieving lower energy consumption (2.75~3.06kWh/kg) and higher current efficiency (88.4~89.7%). SEM images showed grain size is significantly increased in higher applied voltages. While at higher temperatures, it seemed to generate particle growth as clusters at the outer deposit layer.

Jan 1, 2014

The Mine Safety and Health Administration (MSHA) defines an independent contractor as any person, partnership, corporation, subsidiary of a corporation, firm, association or other organization that contracts to perform services or construction at a mine. Contractors that perform specific types of work are required to report the number of employees who work at coal mines and noncoal mines.

Jan 1, 2008

By Aner W. Erickson

"Magnetite iron deposits on Tolstoi Mountain were examined as part of the investigations by the Bureau of Mines of iron and copper ores on Prince of Wales Island. The Tolstoi Mountain project was a part of a program for investigating mineral deposits in Alaska, under the general supervision of R. S. Sanford, acting branch chief.A preliminary examination was made by S. P. Holt, mining engineer of the Bureau of Mines, in company with John Reed, L. A. Warner, and W. S. Twenhofel of the Federal Geological Survey, on July 14, l943. Three samples were taken, rough estimates were made, and it was proposed that the area be mapped, topographically and geologically,. Dip-needle work was added to the program, and it was decided that, should results warrant, the deposits would be diamond-drilled.From March 26 to May 28, 1944, the deposits were examined thoroughly by Bureau of Mines personnel under the direction of the author. Thirty-two acres were mapped with contour intervals of 10 feet, grids were established covering the principal outcrops, over 1,500 dip-needle readings were secured, and the magnetite bodies were outlined. Additional information was gathered by trench inch and channel-sampling, 600 linear feet of trench being dug and 32 channel samples being cut. Finally, the mapped area was checked for nonoutcropping deposits by taking dip-needle readings at 10-foot intervals along the traverse lines, creeks, trails, and all outstanding topographical features. This re-connaissance work gave sufficient coverage of the 32 acres to eliminate the possibility of further magnetite bodies of any consequence remaining undiscovered.Acknowledgment is made to Nile Johannsen, assayer, Territorial Department of Mines, Ketchfkan, Alaska, for determination of samples.The deposits are on Prince of Wales Island in Southeastern Alaska near Tolstoi Pay, a deep-water indentation at the northwest and of Kasdan Peninsula. The physical features are shown on figures 1 and 2 and the location of the deposition figure 3. Old workings were found on the west side of Tolstoi Mountain; between elevations of 650 and 1,150 feet, at distances of 3/4 to 1-1/4 miles from the east shore of Tolstoi Bay.Access to the area is over a brushed foot trail built by the Bureau of Mines. Topography would permit construction of either surface or aerial tramways at moderate cost but would make road building expensive. Deep-water navigation, permitting inexpensive water transportation, is possible the year around.Kasaan Peninsula is an area of moderate relief, being considerably less rugged than the mainland to the east. Most of the mountains and ridges are less than 2,500 feet in height and show evidence of having been covered by the ice cap of the Pleistocene age. Rock exposures below elevations of 2,000 feet are limited, as extensive overburden 2 to 20 feet deep covers the greater part of the peninsula."

Dec 1, 1948

By J. V. W. REYNDERS

IN THE remarks which I am about to make concern¬ing the safety work of the Bureau of Mines, I want first of all to disengage myself from a disposition, which is frequently in evidence, to give spectacular emphasis to the hazards of mining operations. It is of the' utmost importance to the industrial welfare of our country that the enormous annual requirement of fuel be produced and be made available in our economic activities, with a minimum of distress and hardship. The safety of coal mining is a condition with which. we are all concerned in a fundamental way. And yet we should not rush to accept hastily conceived notions that laxity among employers in respect to safety measures exists to any outstanding degree. In fact in a large number of instances, the precautionary efforts of min¬ing companies, directed to the elimination of accidents are beyond all criticism, albeit the industry suffers in reputation from the carelessness of, its less effi¬cient constituents. The Bureau of Mines has been a leading influence in disseminating the doctrines of safety, in securing the cooperation of the miners themselves, and in stirring up ' the laggards, both among the employers and the employed. It is much to the interest of well-conducted mine operations that the industry, as a whole, observe safety regulations to the utmost.

Jan 1, 1925

By T. Nyabeze

This paper presents the experiences and views of women involved in the mining industry as determined from a questionnaire that was circulated across the Canadian mining industry. Globally, there have been significant studies done to understand the historic and global variety of women?s participation in this industry1. The reason for focusing on women?s experiences here in Canada is because women?s percentage representation at 14.4% in the mineral industry workforce falls below the overall labour force average of 47.4%2. Notably, a recent article in the Globe and Mail newspaper points out that adequate representation of women in leading of organizations is more of a matter of competitiveness and innovation rather than purely a ?women?s issue?3. This paper will provide some insight into the reasons why women join and stay in the mining industry and shed some light into the reasons for the overall low representation in this sector. The authors believe, as stated in a study from the London Business School, that a gender-balanced workforce is one way of providing the best results in areas that drive innovation4. Women represent a key stakeholder group that can help enhance the mining industry?s sustainability through innovation. The women who responded to the questionnaire represent many different areas within the mining industry, including a broad range of roles in industry, government, academia and in the supplies and services sector. The paper is intended to raise awareness about issues that women encounter that contribute or detract from career satisfaction in the mining industry. The survey provides an overall understanding of why women pursue or work in mining, and why women either remain or choose to leave it. The advantages and disadvantages experienced by women are highlighted, along with a summary of the possible initiatives that could be undertaken by employers as opportunities to improve the attraction of the mining industry for career minded women. As well, the survey provides a summary of the top ten features that are already in place at various organizations and community groups that have been identified as key for supporting and encouraging women to join and remain in the industry. Not surprisingly, the survey identifies that one of the key ingredients for retention of women in mining is the provision of mentors and sponsors. Another key aspect for retention is the provision of progressive employment policies that address the need for a degree of flexibility in work hours and a culture of balance between work and personal life demands. The survey and results are portrayed only from a female perspective since it is largely women?s perceptions that will inevitably be transmitted to others who plan on entering the field.

Oct 1, 2010

By Edward Barrody

There are wide variations in the values of heats of explosion and detonation as reported in literature. These values are not “stand-alone” or sole properties of the explosives. Specifications of the conditions under which they were determined are necessary to characterize these values. This paper proposes that these values are dependent on their oxygen content and the surroundings their products “work against” upon expansion. Also, the heats of explosion and detonation values can have the same values, but different products, showing that the products can take “independent paths” but have the same values.

Jan 1, 2003

The Mine Safety and Health Administration (MSHA) defines an independent contractor as “any person, partnership, corporation, subsidiary of a cor-poration, firm, association or other organization that contracts to perform services or construction at a mine.” Contractors that perform specific types of work are required to report the number of employees who work at coal mines and noncoal mines.

Sep 1, 2007

By M. Albrecht

I have been following the discussions on coal degradation started by the article "Degradation process in coal slurry pipe-lines," by M.G. Ayat and B.C. Scott. I agree with Mr. Dasher's comments in January that the title of the article was perhaps misleading as the information appeared to pertain more to processing the coal than to transportation. Specifically, the authors' conclude that the cyclone had an important impact on the degradation. Dr. Ferri's comments on degradation in other physical processes was very correct, handling of coal in a turbulent manner has an impact on the size distribution of the coal. This is one reason that when I design a coal system (mine to rail car) I try to minimize the total number of transfer and processing steps consistent with achieving the desired product specifications. Another area, mentioned in passing in the article, the impact of natural causes and the mining step, is of particular interest to me. A mine in West Virginia had a variation of 50% in the -6.35 mm (-0.25 in.) raw coal depending upon the direction of mining. Since it was a single unit mine, this significantly impacted the final product. Two articles on mining's impact on size distribution are: • Stefanko, R., Chopra, 1K., and Ramani, R.V., 1974, "Mining influence on size consistency and washability characteristics of coal," SME Fall Meeting, September; and • Albrecht, M., and Olsen, D., 1980, "Mining methods impact on coal preparation plant design," 1st International Mine Planning and Development Symposium, September. Both articles presented information on variation of size distribution and cleaning plant performance on a coal depending on the mining method used. Both articles considered a single coal seam at one mining operation. Stefanko's article considered continuous and conventional mining of coal in Pennsylvania. Albrecht's article considered surface, underground continuous, and underground hydraulic mining of a coal in British Columbia. Both concluded that mining methods do impact coal characteristics. I agree with Mr. Ayat's comments in reply to Dr. Ferri's discussion, "... degradation is a multi-faceted phenomenon involving many natural and man-made factors." As efforts are being made to produce a higher quality (lower sulfur) coal, this topic becomes even more important

Jan 1, 1989

By J. S. Kasper, R. M. Waterstrat, B. F. Decker

THE large difference in the X-ray scattering factors for molybdenum and manganese makes the o- phase in the Mn-Mo system an interesting one to study with respect to ordering of the atoms. Such a study has been carried out using data obtained from a powder sample, and the resulting evidence for ordering in this compound is presented here. It is not possible, of course, to obtain all the details of structure for a u phase from powder data only. Most difficult of all would be the determination of precise atomic parameters. There is reason to believe, however, that the atomic parameters do not vary greatly in the different s'S and that the precise values obtained from one s structure would then allow decisions as to the ordering of atoms to be made when there is a large difference in scattering factors. In particular, the powder intensities for Mn-Mo s are for the most part in good agreement with those observed for Co-Cr, for which single crystal studies have been made by the authors.' There are a few marked discrepancies in the intensity comparison of the two s's, and these cannot be removed by adjustment of the parameters. They are interpreted as resulting from a more pronounced effect of ordering of the atoms. Accordingly, the parameters of Co-Cr s' have been used for the calculations of the Mn-Mo intensities. For Co-Cr, the space group is D4h14-P4/mnm with atoms in the following positions: 1—2 in (b); 11—4 in (f), with x=0.1031; 111—8 in (i), with x= 0.3713 and y=0.0370; IV—8 in (i), with x=0.5662 and y=0.2396; and V—8 in (j), with x=0.3160Y and y — -0.250. The unit cell is tetragonal, with an==9.10A and cn=4.74A for the Mn-Mo u phase studied here.

Jan 1, 1955

Outokumpu Technology’s HSC Chemistry process calculation software enables the user to simulate an entire chemical or physical process. The HSC Chemistry 6.0 contains 21 calculation modules and 11 databases for reaction, equilibrium, heat balance, heat transfer, petrological and simulation applications. Most of the calculation modules automatically utilize the same extensive thermochemical database which contains enthalpy (H), entropy (S) and heat capacity (C) data. This database has been expanded to include more than 20,000 species.

Jan 1, 2007

By Clifford C. E

The Black Star and Racecourse orebodies below 15 level contain a major portion of the primary silver-lead-zinc ore reserves of 56 million tonnes at 150 g/t Ag, 6.4% Pb and 6.5% Zn at Isa Mine. Extraction from this area is scheduled to begin in the early 1980's. Mining in this block will be quite com- plicated as the ore is contained in a dozen separate orebodies varying in width from 3 m to 20 m with only narrow barren pillars between them in some cases. Mining objectives which consider metal recovery, costs, environmental and safety factors, operating requirements and rock mechanics are used to compare proposals. The planning work involved in formulating mining proposals considers disposition of reserves, scheduling factors, sequence of extraction, extraction methods, haulage set-up and ventilation requirements.

Jan 1, 1979

By M L. van Kampen

The recent (2005) amendments to the Resource Management Act 1991 have made it clear that there is no obligation on an applicant to consult. However the importance and value in consulting with the community, particularly before commencing a major project, cannot be understated.   This paper looks at the provisions of the Resource Management Act as they relate to consultation and public participation in the process, and will discuss the benefits of consultation both before an application is filed and following the filing of the application. Engaging with the local community can help shape a project to better fit the community, engender support and address opposition. In short, taking the extra step to what is legally required, can help smooth what is potentially a bumpy road. Examples in practice of the value of consultation are given.

Jan 1, 2006

By Mary C. Nodine, Michael P. Walker, Paul Eggers, Donald E. Aubrecht

The CANALSIDE commercial development in Buffalo, New York serves to revitalize the former site of the Buffalo Memorial Auditorium, adjacent to Lake Erie. The Auditorium was constructed in 1940 and founded on steel H-piles driven to limestone bedrock. After decades of professional sport and entertainment events, the “Aud,” as it was locally known, was closed in 1996. It sat vacant until it was demolished in 2009, at which time plans were made to revitalize the area with shops, restaurants, and a historic replica canal. The only portion of the Aud that was left intact was a subbasement boiler room. The subbasement was renovated in 2014 and has since been used to house water and ice making equipment for the historic replica canals, which boast recreational ice skating in the winter. The subbasement floor was about 10 feet below groundwater and the Lake Erie water level. The floor consisted of an approximately 4-foot-thick layered inverted waffle slab system, with reinforced concrete grade beams and concrete infill between the grade beams. A waterproofing membrane was located near the base of the slab. There were no major seepage issues in the subbasement, so the existing waterproofing membrane was assumed to be intact and performing adequately. A four-story building housing a children’s museum was proposed to be constructed directly above the subbasement. The loads imparted by the new building would exceed the capacity of the existing piles, so it was determined that drilling micropiles through the subbasement floor would be the most practical means of supporting the new building. Drilling through the existing slab and waterproofing system was a concern due to the challenges of controlling water during construction and the importance of maintaining the integrity of the permanent waterproofing system.

Jan 1, 2018

By L. Callele, C. DiGiovanni, L. Li, R. Driver

"Hot-dip galvanizing is a common procedure used to protect structural steels from corrosive environments. However, in a construction project involving welded structural steel platforms by a Canadian steel structures company, numerous connections were found with large cracks in the welded corner joints and T-joints after galvanizing. Historically, in other similar projects by the same industry partner, cracking did not occur making this an unforeseen and new phenomenon. The project explored the mechanical properties of the base material, the thermal stresses induced by the hot-dip galvanizing, and the fracture surface of the cracks. A key feature to note, the fracture surface showed intergranular cracking with no plastic deformation. Lab testing showed the base material exhibited intergranular brittle behavior when heated and fractured at the galvanizing temperature. The transition to a brittle fracture mode is due to temper embrittlement and the segregation of elements in the grain boundaries.INTRODUCTION Galvanization is a common practice for protecting steel structures from the corrosive environment. Hot-dip galvanizing is the most common approach to bonding the zinc layer to the steel, and it is highly cost effective. In the case of welded structures, it is common to do the hot-dip galvanizing process after welding. This is so the protective layer can be applied to the structure as a whole and over the welds. In a recent construction project carried out in industry, a steel frame platform structure measuring approximately 3 m x 7 m was galvanized after welding fabrication. The structure was built of CSA G40.21 350W and CSA G40.20/G40.21 300W plain carbon steels and welded using a metal core arc welding process for the flanges and a flux core arc welding process for the webs of the beams. Due to their size, the platforms underwent a double-dip galvanizing process meaning half of the structures were submerged in the molten zinc path while the other half was exposed to the ambient air. This was repeated for the remaining side. Shortly after the galvanizing process was completed, numerous large cracks were found in the welded joints. Given there was no history of weld cracks after galvanizing in previous similar frames that were double dipped, this failure posed a new and curious problem."

Jan 1, 2017

By Larry J. Hulbert, Louis J. Cabri, John L. Campbell, Gilles Laflamme, Chris G. Ryan, Soey H. Sie, Rolando Lastra

"Abstract- The mineralogy of samples from the Wellgreen Cu-Ni-Pt-Pd deposit, Yukon Territory, is complex and the metals of interest are contained within fme-grained minerais which vary in size and mineral associations from sample to sample.The major Ni carriers are pentlandite and violarite; the major Cu carrier is chalcopyrite. About 700Jo of the major Ni carriers and 78% of the major Cu qmier will be liberated at a grind of 80% -'}f,.7 J.Uil (-500 mesh) for typical low-grade gabbro (West zone, sample No. 1). For typical ""clinopyroxenite"" (West zone, sample No. 2) and typical ""clinopyroxene-rich peridotite"" (East zone, sample No. 3) the liberation would be 71""lo and 65% for Ni, 74% and 60% for Cu, respectively. Fine grinding, however, cannot liberate the Ni contained in silicates and pyrrhotite, estimated to total24.5% for typicallow-grade gabbro (West zone, sample No. 1), 15% for typical ""clinopyroxenite"" (West zone, sample No. 2), and 12% for typical ""clinopyroxene-rich peridotite"" (East zone, sample No. 3).The principal Pt carrier (sperrylite) varies considerably in grain-size between samples and fme grinding, required to liberate the major Ni and Cu carriers, may be counterproductive in samples where sperrylite is relatively coarse-grained, as sorne would then be unrecovered (e.g. sample No. 1). In addition, sperrylite in samples No. 2 and No. 3 is closely associated with magnetite.Palladium occurs in diverse ways. It occurs in the form of several Pd minerais (e.g. sudburyite, testibiopalladite, merenskyite), as a replacement for Ni in several tellurides, antimonides and tel­ lurantimonides (e.g. melonite), or as very low concentrations in pentlandite (up to 34 ppm), chal­ copyrite (up to 9 ppm), and pyrrhotite (up to 5.6 ppm). Palladium minerais and Pd-bearing minerals are strongly associated with chalcopyrite in sample No. 1 and will thus report to a Cu concentrate. However, 22% of the total Pd is in solid solution in pentlandite in this sample and will thus report to the Ni concentrate. In samples No. 2 and No. 3, less Pd occurs in solid solution in pentlandite, and the PGM are distributed mainly among pentlandite, chalcopyrite, and magnetite in sample No. 2, and among pentlandite, pyrrhotite, chalcopyrite, and magnetite in sample No. 3. Therefore, the feasibility of magnetic concentration should be investigated for samples like No. 2 and No. 3, in order to improve Pt and Pd recoveries.Rhodium was found to occur as rare hollingworthite, in sparse cobaltite (up to 2.7%) and, as low concentrations in chalcopyrite (to 10 ppm) and pentlandite (to 12 ppm) by proton microprobe. Iridium occurs in hollingworthite (up to 7.8%) and very rarely as the native metal or in an undefmed Re-Ir-Os-Ru alloy. Ruthenium was determined by proton microprobe analyses to occur in pentlandite (up to 13 ppm) and chalcopyrite (up to 10 ppm), in addition to rare laurite and Re alloy."

Jan 1, 1993

Study on Beneficiation Technology of a Refractory Fluorite Ore in North China

Sep 13, 2010

By B McCreath

Industrial process water for the Commodore Coal Mine and the adjoining Millmerran Power Station is provided by pumping secondary treated sewage effluent 100 km from the Wetalla Sewage Treatment Plant near Toowoomba. (A separate source is used for potable water.) The effluent is not of sufficient quality for discharge to a watercourse, but it is suitable, with further treatment, for the mine and power station. In designing and constructing the pipeline, special emphasis was placed on preventing accidental spills or planned releases to the environment. The pipeline and associated works can transfer 1000 ML/annum for reuse in the coal mine and power station.

Jan 1, 2003

By Ana Carolina Abrantes de Souza

O objetivo deste trabalho foi a obtenção de microestruturas diferenciadas a partir de simulações de distintas temperaturas de bobinamento, e o estudo da influência destas microestruturas nas propriedades mecânicas, em um aço baixo carbono com microadição de molibdênio e nióbio laminado a quente. A evolução microestrutural e mecânica foi avaliada com o auxílio de técnicas de microscopia óptica (MO) e microscopia eletrônica de varredura (MEV), testes de dureza Vickers e tração uniaxial, somado a determinação das temperaturas de transformação de fase no aquecimento (Ac1 e Ac3) em um analisador termomecânico (TMA). De acordo com os resultados obtidos, pode-se observar que as diferentes temperaturas adotadas da interrupção do resfriamento (simulando o bobinamento), foram capazes de proporcionar sutis diferenças nas microestruturas e propriedades mecânicas finais.

Jul 30, 2018

By John A. Kost

Previous work performed under Contract H0220003 suggested that the mean incombustible content could be obtained with fewer samples and smaller samples without greatly increasing the sampling error. Under Modification No. 4 additional surveys were made in twelve coal mines, representing six states. Same 2,500 samples were collected, analyzed for incombustible content, and statistically evaluated. The earlier findings were substantiated.

Jan 1, 1975