Search Documents

Coal research and technologic work by the Bureau of Mines covers a broad program of investigation aimed at conservation and utilization of this important natural resource. Conservation is served by a constant search for higher efficiencies in mining, preparation, and use. Increased utilization is sought through various projects that probe new ways to use coal and expand existing coal markets. This report, the twenty-eighth in the series,3 gives the highlights of Bureau of Mines coal research and technologic work in 1963. The scope and complexity of the program makes it virtually impossible to report all progress on every project, even tor a 12-month period. Full insight into each project can be gained only through intensive review of basic objectives, past accomplishments, and current status of the work. Details of the work are given in numerous publications issued by the Bureau and its laboratories and centers located throughout the country.

Jan 1, 1964

By A B. Richards

Time window analysis that limits the explosive mass fired within a specified time window (commonly eight milliseconds) has been used for many years in blast design by explosives engineers. Despite several warnings in the past that this technique has limited practical or scientific basis and, in many cases, does not effectively control vibration, almost every textbook and blasting manual refers to time window charge mass limits as a primary vibration control technique. It has become entrenched in some blast vibration management plans, despite being inappropriate for the particular situation. With the flexible initiation timing available with electronic detonation almost a practical reality, and the 8 ms constraints in-built into the signal tube initiation system thereby lifted, it is timely to review the significance of the 8 ms time window in controlling blast vibration. This paper re-visits the original research that led to the development of the 8 ms criteria and the non-supportive conclusion of the original researcher. Because airblast was not measured, the 8 ms time window was never intended to be applicable for airblast control. Examples of blast designs are given in this paper that comply with the 8 ms time window limit that result in substantially increased air and ground vibration, together with examples of blast design that does not satisfy time window considerations, which results in reduced air and ground vibration. Techniques that identify wavefront reinforcement, due to the combined effect of drilling pattern and delay sequence, can assist explosives engineers to avoid high blast vibration situations that result from the inappropriate application of time window techniques and other adverse delay combinations.

Jan 1, 2003

By H. H. Hughes, J. G. Dunn, P. G. Fernandez, H. G. Linge

Dissolved Arsenic (As) is stabilised primarily as As(III) and As(V) and enters ground water streams from sources such as the increasing metallurgical processing of As - containing ores [1]. As(III) is more toxic than As(V) and is less effectively removed from solution by oxide precipitation. Even for dilute As(III) solutions, skin contact or ingestion can cause dermatitis or cancer and there are stringent effluent control standards in place for As containing effluent from mining operations [2]. Chemtronics (Perth, Australia) has manufactured a compact digital voltamme­ter, based on anodic stripping voltammetry (ASV) and suitable for use in the laboratory or field. In this paper we demonstrate the utility of this equipment for measuring As(III) concentration with a detection limit of ca. 10 ppb.

Jan 1, 1995

A machine that improves safety during the cutting of boxholes (ore-passes) and travelways in underground mining operations has delivered impressive results in trials conducted at a South African platinum mine. The technology is a joint effort by Sandvik Mining and Construction and platinum mining company Lonmin. The ABH 1600 boxhole borer was built by Voest-Alpine Bergtechnik, Sandvik’s Austrian subsidiary. It was delivered to the Lonmin Eastern platinum mine in February 2005. There, it was deployed underground on the Number 8 Level (320 m or 1,050 ft below the surface) at the mine’s Newman incline shaft.

Jan 1, 2006

By S. M. Shelton, J. B. Zadea, M. M. Fine, T. L. Johnston

"INTRODUCTION The Mayfield manganese property is about 25 miles south of Van Horn, in Jeff Davis County, Tex. The ore deposit is developed by a large open-cut and a small stope.An 8-ton sample was received for testing; it was taker at random from material on the mine dumps and consisted of a mixture of manganese oxides, barite, and siliceous gangue minerals. The manganese occurred largely as hard, massive, crystalline psilomelane, with a small amount of pyrolusite. The gangue minerals consisted of intermixed iron-stained sand stone, quartzite, chalcedony, calcite, quartz, and barite. Chemical analysis showed 8.9 percent manganese, 3.3 percent iron, 38.4 percent silica, 6.6 percent calcium carbonate, 7.1 percent barium, 3.1 percent alumina, 0.09 percent phosphorus 0.01 tungstic oxide, and less than 0.05 percentAnalysis of selected clean pieces of manganese minerals, free of gangue, showed 48.1 percent manganese end 13.4 percent barium, of which only 0.2 percent was present as barium sulfate. This indicated a limit in concentration. Barium was also present in the gangue as a separate mineral, barite (BaSO4), which has approximately the same specific gravity as the manganese oxide."

Apr 1, 1942

By P. Lopez, E. Wellman, N. Risso, A. Anani

Current machine learning models used for roof fall hazard prediction are mounted on expensive sensors, computationally expensive, or lack the robustness for accurate prediction in the underground mining environment. This research aims to provide a design methodology for a robust, low-cost, deep learning-based algorithm for underground mine roof fall hazard prediction. A data sampling plan is developed to ensure the replicability and robustness of the developed model. In addition, feature engineering and transformation methods are described to identify relevant features for hazard identification. The methodology described here will be used in model development, tested, and implemented as a real-time mobile device application. The new tool will be expected to detect roof fall hazards in real-time and contribute to a crowdsourcing approach for underground hazard detection.

Feb 1, 2023

By Youn-Bae Kang

Evaporation mechanism of S from liquid Fe–C–S alloys at 1873 K was proposed by analyzing available experimental data. It has been known that increasing C content in liquid alloy increases activity coefficient of S ðfSÞ, and it could raise driving force for the evaporation reaction S = S(g). However, experimental data of the evaporation of S in the Fe–C–S alloys could not be accounted for only by considering the increases of fS. In the present study, formation of carbosulfides, CS(g) and CS2(g), was additionally taken into account in order to explain role of C for the accelerated S evaporation. Surface adsorption of S was also taken into account, which retards the evaporation rate of S. An evaporation model equation was formulated. It can be applied to calculate the evaporation rate of S over wider C content (from zero to its saturation to liquid alloy).

By A. L. Toenges, F. A. Jones, J. N. Sxudder, E. R. Maize

"INTRODUCTION This report is the second of a series of studies of analysis of energy requirements and characteristics of various machines used in the production of coal in underground mines and the losses in distribution of energy to these machines. The test equipment used in these studies is described in Report of Investigations 3615. 7/ The preliminary study data and results of tests made on various types of mechanical-leading cutting, and transporting equipment at two mines. This report is analysis of the energy requirements of the energy requirements of the underground equipment of a third mine. An analysis of the use of energy and its distribution usually requires in a saving in energy consumption and the reduction of hazards. The distribution system should be designed to supply energy effectively and study for the efficient operation of all machines."

Feb 1, 1943

By Thomas Kuhn

The detailed investigation of both active and inactive submarine hydrothermal systems has gained tremendous progress during the last decades because of the increasing usage of remotely operated vehicles (ROV) as well as manned submersibles. Special aspects like the targeted sampling of chimney structures and vent fluids as well as the analysis of zonations of near-surface structures like sulfides mounds was only possible with the usage of such vehicles. However, the availability of such vehicles has been very limited because of the few number of deep-water ROVs and manned submersibles which need both a trained crew and a special research vessel. This was especially true for the German science community which did not have such devices at its disposal until recently. With the ROV QUEST 5 which is based at the University of Bremen (c/o. Prof. Dr. G. Wefer, Dr. V. Ratmeyer) this major drawback has now been eliminated.

Jan 1, 2003

By D. McSwain-Santos

Soda ash is the trade name for sodium carbonate, a chemical refined from the mineral trona or naturally occurring sodium carbonate-bearing brines (both referred to as natural soda ash) or manufactured from one of several chemical processes (referred to as synthetic soda ash). It is an essential raw material in glass, chemicals, detergents and other important industrial products. Production U.S. soda ash production during 2004 increased to10.9 million Mt (12 million st). Five companies comprised the domestic soda ash industry. Four were in Wyoming operating five plants. One was in California with one plant.

Jan 1, 2005

By J. Fletcher Smoak

Consumption of abrasive materials in the United States increased 22% in value over that of 1982 to $320 million; of which, 59% was manufactured abrasive, 35% was industrial diamond (natural and synthetic), and 6% was natural abrasive. Production value of natural abrasives, excluding industrial diamond, remained virtually unchanged. Production of crude tripol, a porous siliceous rock, decreased slightly; however, shipments of processed tripoli increased 13% in quantity and 32% in value. Production of garnet, an abundant iron-aluminum silicate, continued to increase primarily because of further increases in production from one plant that had completed an expansion program in late 1981. Production of special silica stone, both crude and finished, decreased in 1983 because of reduced demand for oilstones

Jan 1, 1984

By C. K. Man

Coal dust explosions in underground coal mines are prevented by generous application of rock dust (usually limestone). If an explosion should occur, the rock dust disperses, mixes with the coal dust and prevents flame propagation by acting as a thermal inhibitor or heat sink. To investigate this process in more detail, a number of explosion experiments using various coal dust and limestone rock dust mixes have been carried out at the Lake Lynn Experimental Mine (LLEM). These were conducted in a single entry of about 1600 ft (488m) in length and initiated with a methane gas explosion. A consistent set of post-explosion floor dust samples were taken along the entry after each test. These dust samples have been analyzed in the laboratory using thermogravimetric analysis (TGA) and solubility to determine how the limestone rock dust behaved during the coal dust / rock dust explosions. The preliminary results are reported in this paper and indicate that the chemistry of limestone plays an important role in its capacity to inhibit coal dust explosions. The results also show that it may be possible to estimate the intensity of the explosion using these conventional methods of analysis. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By E. Ghali, J. F. Dorion

This paper presents the results of on-going investigations on the influence of corrosion on the performance of support systems in selected underground gold mines. Rock support is exposed to various conditions that can be aggressive. Samples of corroded support were analysed using SEM and photomicrography to determine the main corrosion forms. Tests are on-going in controlled corrosion chambers to qualify and quantify the impact of rock and minerals particles on steel corrosion. As more data become available these relationships can lead to useful information on the choice of support systems and reliable estimates of their longevity.

Jan 1, 2011

By C. J. Brown

Since its commercialization thirty years ago, the Recoflo® short bed ion exchange process has been extensively utilized for the recovery of a wide variety of acids and metal salts. In addition to a reduction in resin bed height from 200 cm to 300 cm to 15 cm to 60 cm, the process has a number of features such as utilization of fine mesh resins in a compressed bed which together make it ideal for a number of applications. The process has been extensively exploited, for example, in the metal finishing industry for recovery of valuable chemicals from electroplating, anodizing, etching and pickling wastes. More recently, it has also been applied in the primary metals industry for purification of copper electrolytes and metals recovery from leachates. The paper discusses several of these applications and some of the issues that were found to be key to their success.

Jan 1, 2004

By C. A. Herbert

The mine of the Alpha Portland Cement ..Co., Iroaton, Ohio, ..working in. a. bed of limestone 96 feet thick at a depth of approximately 510 feet below the surface, has established a won¬ derful safety record, having operated 6 years—frcra September 21, 1926,. to September 21, 1932 - without a lost-time accident. This mine, with 61 to 86 employees (average 68) and daily output of 1,000 to 1,200 tons of limestone, operated 1,041 days during the 6-year period, or the equivalent of 578,894 man-hours of exposure. ...... ... . Immediately above the limestone is a 20-foot .bed of hard..sandstone.. At present about 10 feet of limestone is left up as. a roof and.about. 42 feet is being extracted. Of the lower portion of the bed it is believed that about. 25 feet. ..immediately below . the .present workings is suitable for cement and will be extracted later. The mine workings are reached by two rectangular concrete shafts, one a 2-compartment hoisting shaft and the other a 2-compartment air and escape shaft- In the latter shaft one compartment is used as an airway and the other, as a cage compartment fo.r a man and material cage. .. . - . The tipples at both the air shaft: and. hoisting shaft are-of steel. The.ground landings at both shafts are fenced in with hand-operated gates in front of the cage compartments.- The two shafts and the crushing plant, which .is.a part of the hoisting shaft-tipple structure, are adjacent to the mill buildings. The rock is hoisted on self-dumping cages in 4 ton capacity, end-gate, steel cars. An electric hoist with automatic overwind device is used at both the main shaft and air shaft. The controls for the main hoist are in the tipple where the engineman is stationed and from which point he has an unobstructed view of both the ground, landing and the cage coming into the dump.

Jan 1, 1933

By Hinchliffe WD, Griffin A

The desorption of gold from activated carbon is promoted by adding organic solvents to aqueous cyanide solutions. At 65-80¦ the elution of gold is fast and is not affected by water quality. The Micron Procedure involves pretreatment of the loaded carbon with NaCN/NaOH followed by elution with methanol vapour and condensate. Carbon is packed into a column above the distillation pot and acts as a fractionating column. Recovery of the methanol condensate leaves a methanol free concentrated gold solution and carbon containing

Jan 1, 1984

By Jeff Hammer, John McGregor

"The Twin Tunnels, originally constructed in 1964, have become a major choking point for trafficheading up to and returning from the Colorado high country along the I-70 corridor. To increase traffic flow, the Colorado Department of Transportation undertook the first widening of the East Bound Tunnel in 2013. After the successful completion of that project, CDOT began the widening of the West Bound Tunnel in 2014. Both projects had a limited schedule for tunnel construction of just nine months. The innovative blasting and demolition of the existing tunnel lining was a crucial component to the success of both projects. During the construction of the West Bound project in 2014 a large amount of surface bench blasting using conventional methods ran concurrently to the West Bound tunnel excavation to allow for enough room for the new tunnel portals."

Jan 1, 2016

By L. Lariviere, M. Grenier, R. Khalili, D. Shook

A mineral processing facility near Montreal, CEZinc, Noranda Inc., has recently implemented a leading-edge intranet solution for monitoring the performance of plant operations, and providing condition-based maintenance. This innovative multi-faceted software implementation incorporates: web-delivered plant information systems; area-wide control loop performance assessment (using sophisticated algorithms to evaluate poorly performing controllers); and integrated alarm management functions.The system has enabled a project to improve plant operations through better process control. Maintenance technicians, engineers, supervisors and managers all can see the performance of the controllers, and the performance of the plant itself, through webdelivered graphics and reports. Information is combined from many sources, real-time, historical, relational and analytical, to provide a complete picture of plant operation.The web-based solution centralizes the administration of user access, and simplifies the deployment of several different kinds of information to many desktops. It is an extensible system that allows users to create and share their own web pages and data views.The paper will discuss the solution architecture and the improvements the IT, operations, maintenance, and engineering groups have experienced, and overall benefits to the facility.

Jan 1, 2003

By Chris Cross

A working group from Anglo American, BHP Billiton, Rio Tinto and Xstrata reviewed supply and demand for graduates from mining education departments in countries where they normally recruit: Australia, Canada, Chile, Western Europe, South Africa and USA. Departments are typically small and increasingly unsustainable, resulting in a steady rate of closure. Supply and demand for graduates in the minerals industry is cyclical, with supply lagging behind demand and trending downwards. Currently, supply is tight and the industry is trying to expand with an ageing workforce. Greater collaboration between universities and within the industry is recommended to address these issues.

May 1, 2006

By Syd S. Peng

Is the laboratory sized coal specimen much stronger than underground coal pillars? The answer to this question has a profound implication to many coal operators. It will decide how much of the coal reserve can be recovered. Or, in many cases, it will determine whether it can be mined economically. Recent trends in several eastern states to establish regulations regarding coal pillar design to prevent surface subsidence long after mining heighten the debates. And, in some cases, these trends highlight the existing practices that seriously question the conventional wisdom. Currently, nearly all researchers and practitioners agree that as the size of rock specimens increases, its strength decreases. This concept has been universally adopted as the basic principle for coal pillar design in the United States. Several formulas have been derived to account for this effect. The reduction factor for underground coal pillars ranges from one-half to one-sixth of the strength obtained in the laboratory, depending on the formula selected. Recent case studies indicate that the reduction factor is not justifiable, at east in some cases. The use of a reduction factor is based on the assumption hat smaller rock specimens as tested in he laboratory contain none or fewer fractures or planes of weakness than larger specimens or underground coal pillars. In other words, the larger the rock materials, the more fractures it contains and subsequently weaker in strength. Do all underground coal pillars have more fractures than laboratory sized coal specimens? Not necessarily. All coal contains cleats. Some are con¬spicuous but others are not. In terms of cleat density (number of cleats per unit area), there is no difference between an underground coal pillar and a laboratory sized specimen, provided the specimen size is larger than the cleat spacing, which is mostly 25 to 75 mm (1 to 3 in.).

Jan 1, 1993