Search Documents

By D. P. Tao, J. G. Groppo, R. Killmeyer, W. W. Wen, B. K. Parekh

Economical dewatering of ultra-fine (minus 74 m) clean coal slurry produced in column flotation to a 20 percent or lower moisture level will be an important step in successful implementation of the advanced fine coal cleaning processes. The main objective of the present study was to evaluate efficiency and effectiveness of three dewatering techniques, namely, hyperbaric, vacuum and screen bowl centrifuge, in dewatering of ultra-fine (D50 ~ 25 m) clean coal slurry produced by the `Ken-Flote' columns operating at the Powell Mountain Coal Company, St. Charles, Virginia. he hyperbaric filter using 3 bar pressure and 165o cake formation angle, provided a filter cake with 23.6percent moisture with a throughput of 800 Kg/m2-h and air consumption of 868 Nm3/t (460 scfm/t). The vacuum filter with 30 percent submergence provided a filter cake with 27.8 percent moisture with a throughput of 122 Kg/m2-h. The screen bowl centrifuge provided a dewatered product containing 32.9 percent moisture at a feed rate of 450 Kg/hr, however, the solids capture was only65 percent. Addition of 1 Kg/t of a cationic surfactant provided filter cakes with 19.1 percent, 23percent, and 34 percent moisture using hyperbaric, vacuum, and centrifuge, respectively. Similarly, addition of 0.5 Kg/ton of copper chloride lowered filter cake moisture to 20.7 percent and 24.8percent, using hyperbaric and vacuum. With the centrifuge no improvement in filter cake moisture was noted. However, use of 80 Kg/ton of `orimulsion' in the centrifuge provided dewatered product containing 26 percent moisture, and the solids capture increased from 65 to 95 percent. The dewatered product appeared dry and was easily handleable.

Jan 1, 1999

By Yu Zhenquan

At the construction site of Bao Shan Iron &. Steel Mill in Shanghai, lots of RC driven piles with length of 50 to 60m were applied. The most unfavourable distribution of stress along the pile shaft was known by measuring the compressive and tensive stresses. With analysing the test results a phenomenon of impact fatigue of RC pile was discovered, the range of impact fatigue and its critical zone can be distinguished. Finally some countermeasures are presented to avoid the impact fatigue of RC long pile.

Jan 1, 1991

By J. A. Smith

The topic assigned me by the Chairman of the Institute, "Safety Practices in Franklin and Williamson Counties, Illinois," I fear will necessarily resolve itself into a paper on shale dust, its application and the results obtained. I returned .only last week from a three weeks trip through these counties at which time, through the courtesy extended me by the operators, I had ample opportunity to visit and inspect many of the largest mines in the field, some of which are among the largest in the United States. With the exception of shale dust and ventilation, I see but vary few instances where the Illinois mines are further advanced in safety precautions than the western mines, and in some respects I believe the operators of the West are further advanced in safety methods than their eastern brothers. Great care is exercised in handling of all ventilation currents. This is an aboslute necessity, as this field is quite gaseous, and the peculiar geological structure of the overlying and underlying strata makes airtight seals very

Jan 1, 1924

By Jheison Lopes dos Santos

O presente estudo teve por objetivo principal produzir um cerâmico composto de alumina, nióbia e fluoreto de lítio de forma a otimizar o uso do forno na etapa de sinterização. Para isso, ponderou-se a respeito da necessidade ou não de utilização de um patamar a 1000°C utilizado em estudos anteriores. Além disso, buscou-se diminuir a temperatura de sinterização, assim como o tempo de permanência em tais temperaturas. O composto cerâmico (Al2O3–4%Nb2O5)–0,5%LiF foi sinterizado a três temperaturas diferentes (1200, 1250 e 1300 ºC), com tempo de patamar de 1h. Foi realizado ensaio de Arquimedes para analisar sua densificação e determinar sua densidade. As fases formadas nessas temperaturas foram identificadas por difração de raios-X. Os resultados mostraram que a maior densificação foi obtida para a maior temperatura, de 1300 ºC. Foi possível observar também que um patamar de apenas 1h na temperatura de sinterização de 1300 ºC apresentou igual densificação a de outros trabalhos, com tempo de patamar de 3h. Este fato sugere que a temperatura tem maior influência na sinterização do que o tempo de permanência. Verificou-se ainda que as mesmas fases foram formadas nas três temperaturas investigadas, sendo tais fases as mesmas detectadas em trabalhos anteriores com patamares maiores. Isso mostra que o prolongado tempo de 3h no patamar de sinterização apenas favorece o crescimento dos grãos, bastando apenas a permanência de 1h para alcançar os resultados desejados e com grãos menores.

Oct 30, 2017

By John Yenter

"Unique blasting problems during reconstruction and expansion of 100 year old buildings toaccommodate gambling. Located on steep mountainous terrain and linked by narrowroadways, the towns of Central City and Black Hawk challenged blasters to exceptionalmeasures in order to control over_break, vibration, public exposure and damage to thecharacter of these historic mining towns. Utilities were also upgraded to fit demands of asmuch as 800% volume change in one year."

Jan 1, 1993

By C. W. Allen, L. C. Moore

THE Mather mine, of the Negaunee Mine Co., is within the limits of the City of Ishpeming, on the Marquette iron- range in Michigan's Upper Peninsula. It is named for William G. Mather, who has served as President, and Chairman of the Board, of The Cleveland-Cliffs Iron Co. for well over 50 years. The property comprises nearly the square mile of section 2, T.47 N. R.27 W., which, except for 20 acres in the northeast corner, was leased by The Cleveland-Cliffs Iron Co. to the Negaunee company. The latter is a partnership of Cleveland-Cliffs and the Bethlehem Steel Co., organized to equip the property, retaining Cliffs in charge as operator. Shipments of ore from this area are mainly through Marquette, which is 16 miles to the northeast on Lake Superior, or through Escanaba, a Lake Michigan port, 65 miles to the south. Cleveland-Cliffs, in 1943, operated 12 mines in the Lake Superior district, with shipments of 6,635,576 tons for the year. GEOLOGY The north footwall of the Marquette Range synclinorium outcrops near the north line of sec. 2, the iron formation dipping to the south at an angle of about 40º. The south side of the trough reappears at a distance of 4 ½ miles on sec. 26 and the surface geology between shows iron formation or intrusive diorites. The latter are harder than most phases of the iron formation and, as a result of glacial action, appear as buttes or low-lying hills. The general elevation of sec. 2 is about 1450 ft. above sea level, or 850ft. above Lake Superior, and the higher diorite outcroppings about 1600 ft. above sea level. The geological structure has been complicated by a series of major and minor faults, one of which may be illustrated by the diorite sheet, which tilts south with the iron formation in the north half of the section and then reappears near the center to repeat this sequence. Sectionally the geological series includes a nearly eroded capping of Goodrich quartzite followed by the considerable thickness of Negaunee iron formation, which is cut by intrusive dikes or diorite sheets, and underlain by the Siamo slates grading into quartzites. The ore deposits occur mainly in troughs formed by the intersection of impervious dikes and the footwall slate, but include locally enriched lenses or bands in the iron formation and also interbedded with the Siamo slate. The ore is a soft red hematite with an indicated dried analysis from the surface drilling to date of 61.50 per cent Fe, 0.134 per cent P, 5.40 per cent Si, 2.87 per cent Al and 0.015 per cent S. EXPLORATION A diamond-drilling campaign started in 1937 actually had its inception in 1917, when a number of shallow test holes were put down for the purpose of locating ore that might be quickly developed and mined

Jan 1, 1945

By John K. Irwin

Friction hoisting has assumed a major role since its introduction to North America less than ten years ago. Interest was illustrated by a recent visit of the Adirondack Section of AIME to a new friction hoist at Chateaugay mine of Republic Steel Corp. at Lyon Mountain, N. Y. The 80-in. diam, 4-rope machine at Lyon Mountain is typical of modern friction hoists. The hoist is mounted on a structural steel tower without deflection sheaves.

Jan 10, 1963

By C. S. Anderson

GEORGIA, since 1829, has produced nearly $18,000,000 from her gold mines, but in late years the output has dwindled to insignificance. In view of present universal efforts to increase gold production, it seems pertinent to record some recent observations in that field, briefly review its past and weigh probabilities of reviving gold mining there. Little in this paper can be claimed as new or original, and it does not present results of a detailed or profound investigation of the whole region. The Allatoona gold mine was reopened in January, 1932, and explored at greater depth during the period from January to June of that year. A number of other abandoned mines were visited, but since the workings, in common with most such mines in Georgia, were flooded or caved, underground conditions could not be examined. For a wider knowl-edge of the subject, a search was made through available pertinent literature and statistics, a bibliography of which is appended hereto. To all the sources obligations are gratefully acknowledged.

Jan 1, 1933

By P. Strand

Talk Outline ? Location and Regional Geology ? Two Unique Kimberlite Sources ? Mineral Chemistry ? Petrography, Age Dates ? Geophysics ? Exploration and Challenges ? Dyke versus Pipe dispersions ? Geophysics ? Prospecting ? Diamond Results ? Summary & Conclusions

May 1, 2008

By W. G. Worcester

THE chief object in presenting this paper on bentonite is to attract general attention to one of the least known and most neglected industrial minerals of Canada, a mineral of extensive commercial possibilities, as evidenced by its development and exploitation in other countries, principally in the United States and Germany; countries upon which some of our most important Canadian industries are dependent for their supply of special clays, such as Fuller's earth and activated bentonite. It was in view of these conditions and the knowledge of the presence of large quantities of bentonite in the Canadian West that the work here reported on was under-taken. While the investigational studies have not been completed, the results indicate that among the many samples tested there are some of real merit and industrial importance. While it has been the author's privilege to examine deposits and samples of bentonite from all of the Western provinces, his chief activities in the field and in research studies have naturally been confined largely to Saskatchewan materials. Notwithstanding this, however, this paper is presented in the hope that it may stimulate a more general interest in, and study of, Canadian bentonites as a whole, a matter of such importance that provincial boundary lines should be overlooked. GENERAL CHARACTERISTICS OF BENTONITE According to Schurecht and Donda (1), bentonite is commonly composed of the mineral montmorillonite, (Mg,Ca)O.Al203 5SiO2 .nH2O, though some are known to consist of beidellite, Al2O3 3SiO2.nH2O: where n is approximately 4, and in certain cases the Al2O3 may in part be replaced by Fe2O3. For present purposes, however, it may be sufficient to state that, in general, bentonite is a "soapy' clay-like mineral or group of minerals composed largely of hydrous aluminium silicate, but frequently carrying small percentages of the alkalies, alkaline earths, and free silica, as well as silicates, gypsum, and other admixed detritus such that purification is usually necessary.

Jan 1, 1937

By T. W. Harris

This paper was written in conjunction with the work being undertaken by the Technical Committees on Classification of Coal, and an effort has been made to compile information relative to the use of coal for stationary steam generation in order to use this information to assist the Committee on Classification of Coal for the ultimate purpose of elimination of losses both by the reduction of individual effort and waste in the consumption of material. Under the auspices of the National Association of Purchasing Agents, a questionnaire was drawn up to develop this information from stationary steam plants throughout the United States in order to consolidate the information developed from the many hundreds of boiler tests on coals consumed by various coal-burning equipment. These questionnaires covered: 1. The company reporting, location and method of delivery to the plant. 2. Complete coal data, including description of coals used (with sufficient space to include first, second and third preference) on source of coal used, complete analysis and factors affecting choice of coal used. 3. Plant data, divided into: (a,) hand-fired, (b) overfeed stokers, (c) underfeed stokers, (d) traveling grate stokers, (e) pulverized coal; and included complete description of furnace data, draft data, coal-burning rate, type of stoker, type of pulverizer, efficiency data and remarks. The questionnaire was drawn up by consultation with various combllstion engineers, including B. J. Cross, Test Engineer of the Combustion Engineering Co., W. H. Fulweiler, of the United Gas Improvement Co. and the U. S. Bureau of Mines. In all, 11,538 copies of the questionnaire have been distributed, of which 4369 were sent in duplicate. Our estimate of the total volume of bituminous coal consumed in stationary steam boilers over the 12 months of 1930 is approximately

Jan 1, 1934

By James C. Cawley

A summary is presented of existing leaky feeder communications systems currently in operation in North America. Background information pertaining to previous use of leaky feeder technology is discussed along with the survey methodology. A review of some pertinent facts concerning propagation in tunnels and specific reference to mine tunnel propagation is presented. A summary of the characteristics of each mine visited is presented in tabular form, and methods of procurement and maintenance are discussed. The role of user training in efficient system use is presented. Seven sites representing eight mines are included in the survey. Economic and technical topics are considered.

By Gary Kahn

The knowledge of how and when your explosives go off can help you make intelligent decisions regarding future application of explosives thus removing some of the black magic associated with blasting. The net result will be intelligently set-up shots with timing, explosive charges, and placement more accurately done. Lower operational costs can be achieved when the correct combinations are applied.

Jan 1, 1989

By Peter Loehr

Full-face tunnelling machines were introduced into German coal mines 12 years ago. It was aimed to utilize these highly efficient systems to drive mine tunnels in rock so that the large demand for development work in some mines could be met. A characteristic feature of coal deposits in Germany - and particularly in the Ruhr Area - is a thick overburden strata. Access is therefore only possible through vertical shafts. A network of horizontal drivages leading from these shafts open the deposits between the different mine levels. The hardcoal-bearing formations are multi-folded and heavily tectonically stressed. Apart from a few extensive fault zones there are many single faults of different natures in the carboniferous strata. During the course of decades coal mining has penetrated to ever increasing depths. Nowadays coal is mined from depths of between 600 m and 1,200 m. The effects of ground pressure in connection with extremely varying rock strengths and high temperatures are particular difficulties which have to be overcome during drivage work. The first full-face tunnelling machines to be applied in the mines had originally bee deigned and developed for tunnelling projects. Not only the machines themselves, but also the back-up equipment had to be adapted to meet the special demands of German coal mines.

Jan 1, 1983

By J. H. Zietsman, W. J. Leipoldt

"To be able to responsibly develop a multiphysics model of the steel belt sintering (SBS) process used to sinter chromite fines, it is important to have a comprehensive understanding of the process. This understanding was gained through a site visit, observation of the process in operation, and interaction with the operators. Material characterization will also reveal much about the process that is not yet fully understood. A well-defined and representative mass and energy balance will also give valuable insight into the process. The plan for the multiphysics model aims to combine a computational fluid dynamics (CFD) model with a discrete element method (DEM) model.To obtain a more accurate mass and energy balance representation of the SBS process, it was decided to develop a dynamic distributed parameter model of the mass and energy balance. This model will be used to gain better understanding of the SBS process so that a more complicated multiphysics model can be developed later. The reason for this is because the SBS process is very dynamic, with a large temperature distribution throughout the length of the process. In its current state, the mass and energy balance model is capable of handling solid and gas material packages and exchanging heat between these packages where they are mixed, and is able to model the heating of the gas by burning CO gas. The next step in the development of the model will involve enabling it to handle evaporatoin of liquid water, burning of solid carbon in the pellets, reduction of iron oxide in the pellets with the CO gas formed from carbon combustion, and then oxidation of the reduced iron in the oxygen-rich cooling zones."

Jan 1, 2014

By Fearnsides W. G.

The map shows the sites of collieries and important boreholes in the district, with approximate underground contours of the pre-Permian surface of the Coal-Measures and of the Barnsley Bed

Dec 1, 1916

NEW MEMBERS. The following list comprises the names of those persons who became members during the month of September, 1913: Members. ANDERSON, ANDREW P., Min. Engr 908 Story Bldg., Los Angeles, Cal. ANDROS, STEPHEN 0., Min. Engr University of Illinois, Urbana, Ill. BECKETT, PERCY G., Min. Engr Globe, Ariz. BLAIR, THOMAS S., JR., Prest. Blair Engrg. Co 343 S. Dearborn St., Chicago, Ill. BOYLE, HARRY, Min. Engr S07 Lowman Bldg., Seattle, Wash. BRADEN, EUGENE B., Vice-Prest., Selby Smelting & Lead Co., Merchants Exchange Bldg., San Francisco, Cal. CHALMERS, JOHN W., Min. and Elec. Engr., Morro Velho, Villa Nova de Lima, Honorio Becalho Minas Geraes, Brazil, So. America.

Jan 10, 1913

By Peter A. Adcock, Rob Fraser

Interest in monitoring nucleation overpotential in electrometallurgical processes dates back some 40 years or more. Conversely, remarkable progress has been made in recent years on describing in detail the processes involved in the formation of thin films by electrodeposition. The newer body of work underscores a need for greater clarity in speaking about the role of nucleation and in the acquisition and interpretation of nucleation overpotential measurements – the aim of this paper. In electrometallurgy, it is generally desirable to form deposits that remain smooth, compact, and relatively fine-grained while the deposit grows to a thickness on the order of 5-10 mm, about 100 times thicker than technological thin films. Hence, we distinguish two kinds of nucleation that can result in formation of new grains:- (1) initial nucleation (onto the substrate surface) of islands that coalesce into growing deposit, and (2) ongoing nucleation of new grains on the deposit surface long after the substrate has been covered and ceases to have a direct influence. Nucleation overpotential of the first type should be measured on an electrode surface truly representative of a real industrial substrate. The second type requires judicious choice of electrode material – an “ideal foreign substrate”. In general neither the industrial substrate nor native metal to be deposited is suitable for measurement of the second type of nucleation overpotential, because of interference by other processes. For the future, clear terminology is needed to distinguish these two types of nucleation potential. The second is the one for which the type of plot dubbed by Moats and Derrick as an “Adcock plot” and by us as a “Kerby-Adcock plot” was first conceived and correlated with relatively thick zinc electrodeposits. The data of Moats and Derrick showing trends for copper electrodeposition on stainless steel and on copper electrodes are interpreted within this framework.

Jan 1, 2016

By He De-wen

The municipal solid waste is a by-product of the daily life of urban residents. The quantity and ingredients of municipal solid waste has exceeded the current management and disposal ability, which has done a great harm to municipal environment and sanitation quality and threatened people?s health. On the basic of analysis on the amounts and main elements of municipal solid waste of Changsha City, the sanitation landfill, incineration, composting, reclamation and utilization technology of household waste were compared specifically in this paper. Based on the concrete conditions of Changsha City, the paper has proposed a disposal proposal combined with reclamation and landfill of municipal solid waste of Changsha City, and the environmental benefit, social benefit and economical benefit of the prepared processing routes were also analyzed in the paper.

Jan 1, 2009