Search Documents

By D R. Swinbourne, T Lehner

Study of the distribution of minor elements between copper matte andfayalite slag is important in determining appropriate methods tomaximise the recovery of valuable metals and the rejection of harmfulelements. Boliden Mineral AB operate a large copper smelter in northern Sweden, where they had noted that the loss of silver to the slag in the settling furnace appeared to be a direct function of the tin content of the slag. This work was aimed at determining whether or not this was a cause-and-effect relationship. Copper matte containing approximately 50 wt per cent copper and small amounts of silver and tin was equilibrated with silica-saturated fayalite slag at 1250¦C, then quenched. The matte and slag were then analysed for their silver and tin contents. It was found that there was no relationship between the silver distribution and the tin distribution. The silver matte/slag distribution ratio had a value of 120 ¦ 40 while that for tin was 2.8 ¦ 0.3. It is suggested that the most likely cause of the relationship observed at the Boliden smelter was matte entrainment in the slag.

Jan 1, 1999

By D Craw, N Newman

Previously published stream quality data and AMD (acid mine drainage) analyses have been collated into a database (DAME û Database for Assessment of Mine Environments) and additional samples including NMD (neutral mine drainage) have been collected from coal mine drainages on the West Coast. Variations in the chemistry of mine drainage samples can be related to four factors: 1.       regional geology (Brunner Coal Measures or Paparoa Coal Measures) 2.       mine type (open cast or underground) 3.       hydrogeology 4.       local geology   In general mines hosted in Paparoa Coal Measures produce NMD whereas mines hosted in Brunner Coal Measures produce AMD with highly variable chemistry. Differences in coal mine drainage chemistry between mines hosted in Brunner and Paparoa Coal Measure sequences can be measured with acid-base accounting geochemistry. Correlation of ANC (acid neutralising capacity) and MPA (maximum potential acidity) analysis of rocks with mine drainage samples is substantially better than correlation of NAG (net acid generation) analysis with mine drainage chemistry.   It is likely that NAG analysis over estimates acid generation potential of some samples due to release of organic acids that are not released under environmental conditions. In general, differences in mine drainage chemistry between Brunner and Paparoa hosted mines are attributed to the effect depositional environment and diagenesis on coal measure composition. Exceptions to generalisations relating mine drainage to Paparoa or Brunner host rocks are likely where local geological conditions cause increased deposition of pyrite in Paparoa rocks and additional analyses are required to confirm interpretations.   Based on the interpretation of these results a mine drainage chemistry hazard model has been constructed. The hazard model predicts likely variations in mine drainage chemistry based on the four factors listed above. The hazard model has implications for mine related water quality risks. For example, ecotoxicity, human health affects and selection of remediation techniques are all sensitive to mine drainage chemistry.

Jan 1, 2006

By V. E. Chrapunov, T. V. Chnyrenkova, R. A. Isakova, V. A. Luganov

Arsenic-gold bearing ores are used as a flux in smelting or leached out to extract gold. To decrease arsenic content in processed materials and to break up the lattice to free the gold, raw materials are roasted. This article analyses the results of laboratory and pilot testing of dissociating and oxidizing roasting of gold-arsenic bearing concentrates. During the dissociation roasting under vacuum arsenic is sublimated into elemental and sulfide forms. The process allows to minimize the negative influence on the environment but requires costly engineering solutions. Roasting in a neutral medium or with limited quantity of oxygen in the gaseous phase makes it possible to sublimate arsenic in the form of oxides and sulfides and may be carried out in the autogeneous mode in fluid bed furnaces. If oxidizing roasting of the concentrates is done in the presence of soda, practically all arsenic and sulfur form water-soluble compounds and remain in cinder.

Jan 1, 2002

By Homor N. McDonald, G. Dale Coe, Will H. Coghill

"INTRODUCTION Sporadic beneficiation tests have been made on the Birmingham (Ala.) red iron ores for the last 55 years. Now, gravity-concentration plants are in operation, of tables are in use. A major problem, as seen by the present writers, is to obtain a coarser concentrate and add to the recovery without increasing the quantity of slime. The oily practicable solution found so far is to recover, by means of concentration (hydraulic) classifiers, the coarse concentrate normally lost in the table middling and, by a similar method, to recover middling particles from the table tailings The size and shape of the coarse concentrate Particles combine to cause them to report in the table middling rather than in the table concentrate. Similarly, mineral is lost in the tailing. Because of this, the nature of the ore, the deportment jerking table, plant tests on classifiers and tables, and the suitability of small concentration classifiers to treat table zonal middlings are discussed herein.The work was done by the Southern Experiment Station, Bureau of Mines, in cooperation with the University of Alabama, Tuscaloosa, Ala."

Jan 1, 1935

By Admilson José Borges

Substituir todo o texto de orientação deste Template pelo conteúdo de seu trabalho. Inserir o texto com no máximo 1.500 caracteres (200 palavras), sem uso de parágrafos. Deve conter, de maneira concisa, o objetivo, a metodologia, os resultados e as conclusões do trabalhoO presente trabalho buscou identificar as principais oportunidades de melhoria na operação de carregamento de vagões no pátio de produtos na mina de Alegria em Mariana, com o propósito de aperfeiçoar, estabilizar e padronizar o processo, consequentemente aumentando-se a produtividade das pás carregadeiras CAT 990, minimizando o tempo de estadia do trem no pátio de produtos e o custo da operação. A elaboração do estudo no setor de expedição de produtos foi baseada em decisões orientadas pela ferramenta de melhoria contínua Seis Sigma e em análises de fatos e dados. Os resultados foram validados através da superação da meta estabelecida para o projeto, onde o objetivo inicial foi aumentar em 8,1% a produtividade do equipamento em relação ao valor atual, porém conseguiu-se atingir o valor de 23,5% com um ganho anual de R$1,34 milhões.

Oct 30, 2017

Jan 1, 1944

Jan 1, 1944

By J. A. Botín

Identifying, quantifying and minimizing technical risks associated to investment decisions is a key challenge for the minerals industry decision takers and investors. However, risk analysis in most bankable mine feasibility studies are based on stochastic modelling of project NPV which, in most cases, fail to provide decision makers with a truly comprehensive analysis of risks associated to technical and management uncertainty and, as the result, are of little use for risk management and project optimization. This paper presents a value-chain risk management approach where project risk is evaluated for each step of the project lifecycle, from exploration to mine closure, and risk management is performed as part of a stepwise value added optimization process.

Jan 1, 2011

Flotation testing has been done at laboratory scale on hematite mineral and ore samples using stage additions of various hydroxamates. Chemisorption of hydroxamate species onto the hematite surface was inferred from the results, possibly involving both the undissociated hydroxamic acid and hydroxamate ion as maximum recovery occurred close to the pKa of the hydroxamic acid. Flotation testing on a specular hematite ore containing 40 per cent Fe and 42.5 per cent silica gave highest iron grades in concentrate at pH 6, in contrast to published data which suggested pH 9 as the optimum value for ore processing. Using octyl hydroxamate, a rougher concentrate assaying 67 per cent Fe at 51 per cent recovery was obtained using four stage additions of 50 g/t at pH 6. For lower grade concentrates still meeting the chemical analysis for pigment grade micaceous hematite (minimum Fe assay 60 per cent) iron recoveries of 80 per cent were possible for stage additions of 50 g/t octyl hydroxamate in the pH range 6-8.

Jan 1, 1999

By R. M. Cunningham

Asarco operates one of the largest individual copper electrolytic refineries in the world at Amarillo, Texas. The feed for this refinery is a mixture of anodes produced at Asarco smelters and copper purchased t?om a number of primary and secondary sources. The variation in feed makes it imperative that the refinery practices state-of-the-art quality control to minimize the effects'of unwanted impurities in the electrolytic refining process. In late 1993, a plant designed to sigru6cantly reduce the antimony and bismuth levels in the electrolyte was commissioned. The purification plant uses ion exchange technology in conjunction with a novel strippiing system developed by Zeneca Specialties (U.K.). The strippiing system permits the recycling of the eluant and thus avoids the extremely high costs of stripping with conventional reagents. In addition, the environmental impact of treating the eluant for recovery of antimony and bismuth is minimized. This paper outlines the development of the technology and, in particular, describes the operational practices and improvements at Amarillo since the commissioning of the plant.

Jan 1, 1997

By D. Berkley

"The competitive pressure, the increasing energy costs and the environmental regulations impose substantial challenges to the definition of power plants serving industrial facilities. Primary mining and metallurgical facilities have even greater challenges because they are often located remotely, where the fuel supply can be a problem. The absence of a power grid imposes challenges on the reliability and quality of the electrical energy supply. In addition, the facilities usually require thermal energy too, not only electricity.This paper outlines these types of issues that have to be considered when defining a cogeneration plant integrated with a remotely located industrial facility. It is addressed to the “users” of cogeneration facilities rather than to “generators.” The focus is on analyzing various site-specific design considerations to prescreen the feasible cogeneration alternatives and minimize the number of options to be analyzed from the economics viewpoint. This approach could substantially reduce the engineering effort and schedule during the feasibility phase of the project.The front-end of the paper provides a basic understanding of cogeneration plants of various types to establish a common language. Subsequently, the paper outlines and analyzes specific issues that could be of help in the definition of cogeneration installations for remotely located industrial facilities, with a focus on mining and primary metallurgical plants"

Jan 1, 2003

By H. C. Wade

"Description and UseDischarge liners or pulp lifters as they are sometimes called are a trough type liner used at the discharge end of the mill where ground ore passes to the trunnion.There are basically two methods of discharging pulp. The First and most common is the overflow method. Here ground ore travels from the feed to the discharge end where it exits through the discharge trunnion in an overflowing manner, hence the name ""overflow"". (See Figure I) The second method of discharging pulp is the grate method. With this method you block-off the trunnion and hold the ore inside the mill for a longer period of time. This allows only the desired size of ore out of the mill. Ore passes through the grate liners, into the Vibrathane Discharge liner, and finally down to the trunnion. Greater control of the ore size results wit1 this method as compared to the overflow method and it also eliminates reclassifying and regrinding. (See Figure 2)Types in UsePresently the majority of discharge liners in use today are rubber. (Metal insert and rubber covered) In some extremely course applications steel and nihard are used."

Jan 1, 1980

By W. J. Birch, M. Kirke

Despite increasing competition from mechanical methods of tunnelling, the drill and blast method is often still the most viable method of excavating tunnels in strong and abrasive rock. To advance a tunnel using drill and blast, explosives are loaded into boreholes in the rock and detonated according to a prearranged sequence. On detonation of the explosive, the rock is fractured and displaced from its original position, leaving behind the desired void. Among the secondary effects of a tunnel blast are ground vibrations caused by elastic disturbances that propagate away from the blasted tunnel face. The possibility that such ground vibrations may cause permanent damage to property and substantial nuisance has generated significant opposition to the use of drill and blast, particularly in urban areas. It is therefore essential that the blasting engineer is able to predict Peak Particle Velocity (PPV) vibration levels at locations in the vicinity of the blast site. Such predictive capability enables the engineer to design blasts so as to ensure that ground vibrations can be kept within acceptable levels. The objective of this project was to analyse data obtained from the ground vibration monitoring program undertaken during the drill and blast excavation of a hard rock tunnel in Central England. Seismograph recordings of tunnel blasts contain a vast amount of information that cannot possibly be expressed using a single PPV value. The main focus of the study was to investigate whether predictive capability could be improved by using scaled distance models derived for selected PPV components relating to specific detonator timings in a given tunnel round. This study has established a method of analysis that can unlock this information for predictive purposes. By permitting the extraction of sub-event Peak Particle Velocity (PPV) values and allowing Scaled Distance (SD) models to be derived for individual period numbers or groups of period numbers, the method has the potential to vastly improve PPV prediction from tunnel blasting. The method established could also help diagnose blasting problems and help target blast design modifications, resulting in improved efficiency and excavation rates.

Jan 1, 2005

By J. H. Crocket, J. Andy Fyon

"All gold deposits within the Tisdale Group are spatially associated with carbonate alteration zones; however, not all carbonate alteration zones are host to gold mineralization.Within the komatiitic and magnesium tholeiitic volcanic rocks at the base of the Tisdale Group, discordant and stratabound carbonate alteration zones occur throughout. The alteration zones consist of a ferroan dolomite - quartz inner assemblage which is enveloped by calcite-quartz and an outer chlorite-rich subzone. Factors which control the distribution of carbonate alteration include joint systems, flow contacts, synvolcanic faults and bulk composition of the host rock.Two environments of carbonate alteration can be recognized: 1) The subsea-floor alteration zones developed within the volcanic rock succession where hydrothermal fluids did not discharge directly onto the sea floor. Insignificant gold production has come from this alteration environment. 2) Seafloor zones, which represent points of hydrothermal fluid discharge into the hydrosphere, are spatially associated with felsic volcanic rock complexes and are host to syngenetic, auriferous cherty dolomite.Carbonatized, magnesium tholeiitic basalts, which are host to the auriferous, cherty dolomite, are enriched in antimony (>0.35 ppm), boron (>30 ppm), gold (>5 ppb) and lithium (> 35 ppm), but are depleted in copper ( < 70 ppm), with respect to carbonatized basalts not associated with gold. Orerelated, altered komatiitic flows can be screened using gold (>5 ppb), lead(> 10 ppm), arsenic(> 70 ppm) and antimony (>1 ppm).The habit, petrographic characteristics and certain geochemical characteristics of the altered volcanic rocks suggest that the hydrothermal fluid was of sea-water origin."

Jan 1, 1982

By John Birkinbine

The experience of the past five years has furnished opportunities to study and to partially explain the operation and some of the causes of the short blast of Warwick Furnace at Pottstown, Pennsylvania, as described in the paper read at the Lake Superior Meeting, in August, 1880.* The many inquiries concerning the details of furnace operation which followed the publication of the paper, and the expressed desire of furnace managers to be informed as to future operations of this plant, have encouraged the preparation of the following data. To make the record continuous, and add to the value of both contributions, the present paper commences where the review of a short blast of Warwick Furnace ended, and includes the data of another short blast of two months, and a subsequent continuous campaign of nearly five years, which, by comparison, we shall designate as "the long blast." Frequent visits to the plant in the five years, during which its operation could be studied, and correspondence with the manager, Mr. Edgar S. Cook, have given a knowledge as to general features and details, and the courtesy of the officers of the Company which has given free access to the books of record permits the presentation of data which it is believed will be welcomed by furnace managers. Interest will undoubtedly be increased by the remarkable results which Mr. Cook has achieved chiefly with anthracite coal in a furnace whose details of construction will scarcely be generally admitted as embodying advanced ideas, its height being but 55 feet, with a bosh diameter of 15 feet 6 inches, its bosh-slope comparatively flat, its crucible smaller than the average, and the heat of the blast never reaching 1000&apos; Fahrenheit. At present writing the credit of the best anthracite blast-furnace practice recorded in our Transactions is conceded to be that pursued by Mr. Fackenthal, at the Durham furnace, and Mr. Cook, at War-

Jan 1, 1886

By Murray Gamble

A new type of groundwater cutoff wall has been developed at the University of Waterloo. The Waterloo Barrier? is a steel sheet piling system that incorporates a sealable cavity at each interlocking joint. In order to prevent leakage through the joints, the sealable cavity is flushed clean and injected with sealant after the installation of the piling. The installation and sealing procedures of the Waterloo Barrier? system allow for a high degree of quality control resulting in a very low permeability cutoff wall. Based upon field installations, the bulk wall hydraulic conductivity of the Waterloo Barrier? ranges from 10-8 to 10-10 cm/sec. Recent case histories are presented in which Waterloo Barrier? vertical cutoff walls have been used to prevent the off-site migration of contaminated groundwater or soil gases. In some instances, the Waterloo Barrier? system was used in combinations of applications such as preventing the migration of contaminants, redirecting the flow of groundwater, providing structural shoring for soil excavation and aiding in site de-watering processes.

Jan 1, 1997

By W. T. Millar

"INTRODUCTION The purpose of the Star Lake project was to investigate, by geophysical surveying and diamond drilling, the magnetite deposits in the northwestern Adirondacks, the ultimate objective being to increase iron production in eastern United States,ACKNOWLEDGMENTSIn its program of investigating mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to the national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclu-sion. The Mining Branch, Lowell B. ""Moon, chief; conducts preliminary examinations, performs the actual investigative work, aid prepares the final report. The Metallurgical Branch, Oliver C. Ralston, chief, analyzes samples and performs beneficiation tests.The chemical and spectrographic analyses included in this report were performed at the Eastern Experiment Station of the Bureau of Lines at College Park, Md., under the general supervision of J. B. Zadra, chief, College Park Division, Metallurgical Branch, and under the immediate direction of Dr. Alton. Gobriel in charge of the laboratory service unit.The mineral exploration was under the general supervision successively of John D. Bardill, district engineer, and McHenry Mosier, chief, College Park Division, Mining Branch. The work was done under the immediate supervision successively of J. P. Ryan, N. A. Eilertsen, and W. T. Millar, project engineers."

Sep 1, 1947

By Donald W. Mitchell, John Nagy

Observations made on coking of coal, deposition of soot, dust transport, flame, violence, and related phenomena following experimental coal-dust explosions are summarized. Data are given on gas explosion pressure, flame length, flame velocity, and variation of these parameters with concentration. Conclusions from these observations are useful in preventing similar occurrences in operating mines and serve as a guide in improving safety.

Dec 1, 1963

By T. Lamond, J. O. Costello

Marble is a preferred surfacing material in up-scale buildings. Its use increased in the 1870&apos;s with rising national wealth and declined in the 1950&apos;s when synthetic materials for these applications were developed. Natural marble is now limited to high-end domestic and commercial structures. Cultured marble is a paste of white marble dust and polyester resin cured in molds yielding fixtures of specific finished dimensions. Dyes incorporated at different stages in the mixing cycle mimic shades and veining of natural marble. This paper discusses the filler requirements for cultured marble production and reviews new techniques to cut and finish natural marble.

Jan 1, 1999

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in saline and Pulaski Counties, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251, of which this is the eleventh. The-data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each halt township is followed by a description of each deposit developed in that halt township. The 14 halt-township maps and 77 detail maps of the bauxite deposits in this series at reports give the locations and numbers of all the holes drilled on the project, except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on figure 13 in volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained tram the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each halt township is given with the discussion of that area.

Jan 1, 1948