Search Documents

By Jack A. McQuiston, Thomas A. Cross

Corrosion of equipment and machinery in the coal industry is usually the result of three main agents: acids, chlorides, and abrasion. Acids and chlorides are especially troublesome in coal preparation plants where soluble salts and sulfur in the coal produce a highly corrosive wash solution. Abrasion is common in all operations where coal is handled or conveyed. Together, the acid-chloride-abrasion combination results in some of the worst corrosive conditions found in any industry. The variety of equipment and structures in the coal industry calls for different corrosion control techniques. Table 1 lists the areas of concern for a number of items. Just as there is a wide variety of corrosion problems, there is a wide array of coating materials available. Tables 2 and 3 are selection charts to provide guidance in narrowing down the choices. Experience has shown that a limited number of coating systems work best on coal equipment and structures. These systems are described in Table 4. The good-better-best designation in the table refers to coating system longevity. Good indicates the least costly and shortest service life. In nearly all cases the lowest annualized cost can be achieved by using the coating system rated best, due to the avoidance of costly repaints and unnecessary downtime. The most expensive coating system, though, is worthless unless the coating system is properly applied. Field inspection to insure compliance with specifications is an important aspect, and is a service available from many coating suppliers. Even the best coating systems require periodic maintenance to achieve satisfactory results. Spot rusting from mechanical damage should be repaired annually to maximize the coatingsystem's results.

Jan 2, 1980

Blast vibration analysis under relatively near-field conditions has been carried out in a narrow-vein underground operation. The objective was to characterize the vibration signal (particle acceleration and velocity) from carefully controlled stope blasts. The limitations of such analysis in deriving design guidelines for reducing dilution has been elucidated. It has been shown that identification of each individual hole with specific explosive types can yield explosive-specific predictive equations for particle velocity. This has been coupled with measurement of actual overbreak to arrive at a limiting vibration level to generate a realistic design tool for controlling dilution in narrow-vein mines.

Jan 1, 2003

By R. Hogg, Y. Lee, D. E. Rannels

"Lee, Yu-Chen, Richard Hogg, and D. Eugene Rannels. Extracellular matrix synthesis by coal dust-exposed type II epithelial cells. Am. J. Physiol. 267 (Lung Cell. Mol. Physiol. 11): L365–L374, 1994.—Although integrity of the alveolar basement membrane may influence progression of lung injury induced by inhaled particulates, little is known about direct effects of coal dusts on the alveolar epithelium or its extracellu¬lar matrix (ECM). Effects of dust on synthesis of cell and ECM proteins by type II cells (T2P) was thus investigated. Three coal dusts (anthracite no. 867; bituminous no. 1451 and no. 1361) and mine dust MIT-3, of respirable size, were studied as a function of dose and time over 3 days of primary T2P culture. On day 1, 750 µg/ml of 867 were required to increase relative synthesis of ECM proteins (ECM/cell). MIT-3, 1451, and 1361 were without effect. By day 3, 867 or MIT-3 increased ECM/ cell 60-100% at 300 µg/ml; 1451 produced modest, dose-dependent stimulation, whereas 1361 remained without effect. None of the dusts caused significant cytotoxicity. The results show dose- and time-dependent effects of well-characterized coal and mine dusts to modify partitioning of newly synthesized proteins into the ECM and suggest that coal dust exposure may modulate structure or function of the subepithelial basement membrane.basement membrane; cell culture; inorganic dust; lung injury; extracellular matrix deposition; pulmonary epitheliumCHRONIC EXPOSURE to coal dust may be associated with development of pulmonary fibrosis and consequent loss of normal lung function (see Ref. 26 for review). Al¬though the pathways of inorganic dust-induced lung injury are recognized to involve an inflammatory re¬sponse, the underlying pathogenic mechanisms are not understood in detail. Acute and chronic responses to dust exposure involve a variety of interacting cells of the immune system, including macrophages, T cells, and B cells, along with pulmonary fibroblasts. These responses reflect direct effects of the dust particles, as well as indirect effects mediated by soluble factors, including cytokines and eicosanoids (see Ref. 41 for review).Studies of pulmonary macrophages and fibroblasts following silica exposure suggest that dust-induced damage at the airway surface may involve cellular injury through oxidant-mediated pathways. Coal dusts and related inorganic particulates can activate the alveolar macrophage (42) to produce fibronectin (15) and cytokines, such as interleukin-1 or tumor necrosis factor (4) and/or other soluble products which act locally (29) to cause acute cellular injury and to initiate the progression of fibrotic lung damage (16). Type I epithelial cells are typically more susceptible than type II cells to oxidant injury. Type I cell damage and subsequent death leads to denudation of the subepithelial basement membrane (2, 21) and can be associated with leakage of plasma constituents from the pulmonary vasculature into the alveolar compartment (13)."

Dec 1, 1995

By Edward W. Ames

"The Jewell tunnel property, situated 3/miles north of Garfield, Chaffee County, Colo., was examined by an engineer3 of the Bureau of Mines in June 1943. Field work began September 16, 1944, but was recessed from December 26, 1944, to gay 15, 1945, because of heavy snows, and was suspended July 12, 1945, when rehabilitation of the New York tunnel workings was completed to the point desired.In its program of exploration of Mineral deposits, the Bureau of Lines has as its promary objective the more effective utilization of our mineral resources, to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as seen .as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples of ore and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.For their supervision of the project and their help in revising the report, particular acknowledgment is due Wm. P. Huleatt, district engineer, Denver, Colo., and Paul T. Allsman, chief, Salt Lake City Division, Mining Branch.The property is situated in secs. 15 and 22, T. 40 N., R. 6 E., N.R.F.M. Salida, the county seat, is on the main line of the Denver & Rio Grande Western Railroad. The property is reached from Salida by following U. S. Highway 50 westward for 18 miles to the village of Garfield, near Monarch Pass, then northward for 3 miles by a very steep mine-access road up Taylor Gulch (fig. 1).The highway to Garfield is accessible throughout the year, but the access road from Garfield is generally impassable from December until June because of snow."

Sep 1, 1946

By R. C. Freas

Composite materials are finding new applications daily, ranging from automotive parts to synthetic lumber. The variety of applications seems almost limitless. However, these emerging products bring both new opportunities and new challenges to the field of industrial minerals. One of the primary challenges is from alternative materials other than industrial minerals. Thus the question is asked whether industrial minerals will truly benefit from the growth in market applications for composite plastics. This article highlights some of the opportunities for industrial minerals while focusing on performance and competitive demands on mineral products intended for use in this developing market.

Jan 1, 2000

By D. M. Abbott, H. J. Sandri

The geoscience matrix method has proven useful for valuing metallic mineral properties lacking delineated mineral resources or reserves. However, the method explicitly excludes commodity markets from the factors considered; marketability is assumed. When valuing industrial mineral properties, marketability cannot be assumed, it must considered. Market considerations may also significantly affect the standard weightings of geoscience matrix parameters such as the proximity to known deposits. In some cases, such proximity is desirable but in many cases it is undesirable. Application of the geoscience matrix method to industrial mineral properties therefore requires thoughtful, market-related adjustments to the basic geoscience matrix methodology.

Jan 1, 2000

By Wenshan Zhang

Three important methods of removing Fe in hydrometallurgy of zinc, manganese, copper, nickel, cobalt and etc are described, including neutralized hydrolysis method, jarosite method and goethite method. The reactions, technical requirements and thermodynamic analysis during Fe removal process are also discussed in this paper.

Jan 1, 2006

By Joseph Irons, David Westfall

Three rock tunnel sewer systems are underway in the Chicago Area. (Figure 1) The three are designed to act independently and to be later connected to the future tunnels of the master plan. The tunnel excavation for each of the systems has been completed. One is in the Northwest area within the City being built by the City, known as the Lawrence Ave. System. Another is in the Southwest suburbs, known as the LaGrange-Brookfield Sewer or Southwest 13A, being built by the Sanitary District, the third is in the South suburbs called the Crawford Avenue sewer or Calumet 18-E, Ext. A- being built as a joint venture between the City and the District. The three are similar in that they have the same purpose, the same component parts and their tunnels were constructed in the nigaran limestone using a mechanical mining machine. The purpose of each of the systems is two-fold. First to provide flood relief for existing inadequate sewer systems, and second to reduce the pollution load to the waterways caused by combined sewer overflows. The existing systems in the areas to be relieved are combined sewers built many years ago. The main outlet for the Village of LaGrange, for example, was built in 1908, is badly in need of repair and lacks the capacity to handle the flood flow from the heavily urbanized area it now serves. The dry weather flow from the area is taken off by intercepting sewers. However during

Jan 1, 1997

By Ditend Tesh, Godfrey Dzinomwa, Harmony K. Musiyarira

Namibia is known as water stressed country with a limited amount of fresh water. Therefore, the use of water is an important topic in the country’s development agenda. Water is a shared and finite resource, with high social, cultural, environmental and economic value. However, freshwater resources are under pressure from ore processing, industrialization, urbanization and the demands of a growing population. In Namibia, ore processing, coupled with the anticipated increase in water demand for human consumption and other uses, has created significant stress on the limited water resources of the country. This is critical in the mining industry as water remains typically the prime environmental medium (besides air) that is affected by mining activities. This study sought to investigate the strides made in water management in mining, especially in environmentally sensitive areas of Namibia. Most mining companies operate next or alongside farms, national parks and fishing areas. The overall objective of this research was to highlight the current practices in Namibia’s mineral industry operating in environmentally sensitive areas especially in areas where uranium is being mined and processed. The methodology consisted of comprehensive literature review, field visits to the case study areas, and comparative studies with best practices. This study shows that over a ten-year period, freshwater consumption was reduced by over 55% per tonne of milled ore in uranium mines, resulting in substantive financial savings as well as the delay in water augmentation through desalination. The strategies employed by the Namibian companies involve inclusive stakeholders’ engagement, recycling and reuse, and the minimization of water losses. The realization that the water challenge cannot be solved by any one party acting alone has been fundamental in ensuring environmental compliance within the mining industry in Namibia. Namibia’s industrial leaders have increasingly recognized that reducing the water footprint of mining activities must be one of the key performance indicators for management. The major finding of this study was that Namibia with its unique ecosystems, mineral reserves, and emerging industries can harness a wide range of resources both to improve the welfare of its citizens and to protect the integrity of its environment.

Jan 1, 2017

By A. Martikainen

Field tests concerning a fog mesh method for fog removal are discussed. The first tests were performed at the Pyhäsalmi Mine, Finland. As this study gave promising results, further studies were completed at the Orivesi Mine. The results of these most recent field tests are presented and the two studies are compared. The Orivesi test set consisted of four materials. These included air filter fabric, fibrous filter fabric, a plastic greenhouse mesh, and an aluminium mosquito net. The variation of the Orivesi results was more noticeable than what was found previously. The best fog removal effect of all tests was achieved with the aluminium mosquito net, while the plastic green-house mesh performed worst. The humidity reduction by aluminium net was more profound than any of its precedents. More mesh materials will be tested in the near future.

Jan 1, 2007

The concept of isokinetic measurement of strength was originally related by Hislop and Perrine.(1)Characteristics of an isokinetic exertion are constant velocity throughout a predetermined range of motion. Strictly speaking, a means of speed control, and not a load in the usual sense, is applied in isokinetic exertions.(1)However, load and resistance are definitely present in this technique. In this case, the load is a result of the energy absorption process performed by the device to keep the exertion speed constant. The device prevents energy from being dissipated through acceleration in isokinetic exercise. The energy is instead converted into a resistive force, which varies in relation to the efficiency of the skeletal muscle. Since the speed of motion is held constant in isokinetic exercise, the resistance experienced during a contraction is equivalent to the force applied throughout the range of motion. For this reason, the technique of isokinetic exercise has sometimes been referred to as accommodating resistance exercise. This type of exercise allows the muscle to contract at its maximum capability a tall points throughout the range of motion. At the extremes of the range of motion of a joint, the muscle has the least mechanical advantage, and the resistance offered by the machine is correspondingly lower. Similarly, as the muscle reaches its optimal mechanical advantage, the resistance of the machine increases proportionally. It must be understood, however, that while isokinetic devices control the speed of the exertion, this does not assure a constant speed of muscle contraction. The speed of isokinetic contractions is constant during individual exertions; however, it is also possible to compare muscular performance over a wide range of isokinetic velocities. Increasing the isokinetic speed of contraction will place increasing demands on Type II muscle fibers (fast twitch and fast oxidative glycolytic). Workplace Assessment It is clear that isometric strength testing cannot substitute for dynamic strength assessment when examining highly dynamic occupational job demands. As most industrial work tasks contain a significant dynamic component, analysis of isokinetic strength capabilities appears to offer some advantage to isometric testing in this regard. However, it must be recognized that isokinetic devices are not entirely realistic compared with free dynamic lifting in which subjects may use rapid acceleration to gain a weight-lifting advantage.

Jan 1, 1998

By B. Cavender

Safety departments have traditionally been held responsible for the safety performance of their division or company. This approach leads to a lack of ownership of safety issues by the larger organization. An alternative paradigm is significantly more effective: the members of the work force (managers as well as workers) are fully responsible and accountable for safe production. The safety department is not extinct, however. Its role has changed, to focus on training, litigation, and external relationships such as community relations. This approach was implemented at BHP Copper's Superior mine and mill in Arizona. By obtaining the genuine commitment of the work force to accident-free production, the mill's MSHA incident rate immediately dropped from 7.4 to zero. The mill also ran one year with no MSHA citations. When this philosophy was implemented at the divisional level, the division's incident rate decreased from 9.5 to 1.1,an 88-percent reduction in six months.

Jan 1, 2000

Aamot, Olav Crone, (Member '29) Met , Det Norske Aktieselskab for Elektrokemisk, Industry, Inc , Oslo, Norway Aase, Glenn D , (Junior Member '40) Met Engr , Western Research Dyv , American Smelt & Refin Co , Selby, Calif Abadye, Henry G., (Member '43) Petr Engr , Sr Prod Engr , Long Beach Oil Development Co, 255 So Santa Clara Ave, Long Beach, Calif Abbott, Clarence E , (Member '04) Civil Engr , 'P , Tennessee Coal, Iron & R R Co , 1542 Brown Marx Bldg Birmingham, Ala Abbott, Fred E , Jr , (Member '44) Petr Engr , c/o Arabian American Oil Co , A P 0 816, c/o Postmaster, New York, N Y Abbott, John H , (Member '46) Resident Mgr , Hickman, Williams & Co, 230 No Michigan Ave, Chicago 1, Ill Abbott, R W R., (Member '47) Asst Power Supt, Cananea Consolidated Copper Co , Cananea, Son , Mexico Abbott, Robert H? Jr., (Junior Member '47) Petr Engr, Producing Dept, The Texas Cc, P 0 Box 951, Houma, La Abel, Raymond L., (Member '28) Chem Engr, Prof of Chem Engrg, Univ of Pittsburgh, Pitts¬burgh Pa Abel, Walter D , (Member '32) Min Engr, Div of Corporations, 403 State Bldg , Los Angeles 12, Cal if

Jan 1, 1952

By P. Srinivasan

Corrosion is a major operational problem in amine-treating plants causing significant expenditures each year, Corrosion may become more severe when the amine plants contain process contaminants ? namely heat-stable salts. The heat-stable salts enter the plants with feed-gas streams and makeup-solution, and/or are produced within the plants by reactions of alkanolamine and available carboxylic-acid anions, This work investigated interaction corrosion effects that may exist in amine-treating plants containing a mixture of heat-stable salts, The investigation was experimentally carried out in a 5 kmol/m3 monoethanolamine (MEA) solution containing 0,20 mol/mol carbon dioxide (CO2) loading at 80°C under atmospheric pressure using carbon steel 1018, Six heat-stable salts, including formate, oxalate, bicine, acetate, thiosulfate and chloride, were tested with a series of salt combinations, Potentiodynamic Polarization, Tafel Extrapolation, and Cyclic Polarization were used for revealing corrosion behavior, determining corrosion rate, and examining the pitting tendency, respectively, Results show that thiosulfate induces the most corrosive environment when present either individually or in the form of salt mixtures.

Jan 1, 2005

By A. D. Dalvi

With the current economic situation, the demand for nickel and other base metals has fallen significantly. More than 440 kt/yr world nickel capacity has been taken out of production within the last year, or more than 25% of the total [1]. This situation is similar to that at the end of 1970?s and it will take a number of years for the demand to recover to the levels before the economic downturn. In the meantime, the challenges facing the industry have increased due to diminishing ore grades, more inaccessible and complex deposits, mounting capital and operating costs and the various external pressures which include socio-economic, environmental, and energy challenges. All industries will be faced with paying the ?total ownership costs? in the future. This will only increase the burden on the industry. How to cope with this in what Thomas Friedman calls the ?Energy-Climate Era? [2] will be the most pressing challenge for the next generation of metallurgists and managers. It will force us to take a broader view of the problems and the solutions beyond mere technical. The metallurgists, engineers and project managers will have to look at the overall projects and their objectives in designing the solutions, requiring a top-down strategic approach.

Jan 1, 2009

To provide a means for accurately and reliably warning of impending roof falls or rock bursts and for evaluating support systems. The Approach: Development of a device for measuring rockbolt loads which is not affected by harsh environments nor by eccentric loading conditions and is easily adapted to various size rock bolts. How It Works: The Rock-Bolt Tension Load Cell, developed by the Bureau's Spokane (Wash.) Mining Research Center, is installed on a bolt and sandwiched between a conventional doughnut washer bearing plate and a torqueing nut (Fig. 1). As the bolt takes load, the bearing plate transmits the load axially to the cell through a ball and socket arrangement, compensating for uneven bearing surfaces. The cell body strains in proportion to the applied load: the strain is sensed by welded strain gages as change in electrical resistance. The resistance change is read through a Wheatstone Bridge and, through calibration, the applied load is determined.

Jan 1, 1974

By D. E. Gorse, R. G. Anderson

"Indusmin's history dates back to 1937 when they developed the Blue Mountain Nepheline Syenite deposit at Nephton, Ontario, and began supplying material for the glass, fiberglass, paint, ceramics and rubber industries.Since then, as a subsidiary of Falconbridge Nickel Mines, Indusmin has expanded the Nephton operation, diversified into the aggregate quarries for the construction industries, with operations at Acton and Halton, Ontario, established silica plants at St. Canut, Quebec and Midland, Ontario, to supply the glass, carbide, ceramics, cleanser and concrete products industries, and the purchase of a foundry, Fahramet Limited, Orillia, Ontario, supplying steel and alloy castings to the mining, construction cement and petrochemical industries.Indusmin also has a Technical Resource Centre and Head Office facilities in Toronto.As this paper deals with Indusmin's experience with dust abatement, and although dust control is a concern at the Nephton, St. Canut and Orillia plants, we will be confining this paper to the experience gained at the Badgeley Quarry and Midland plant of the Ontario Silica Operation."

Jan 1, 1980

By Gerald Sanders

Presentation Topics ? We?re Going to the Moon Again? ? What is Lunar Mining ? In-Situ Resource Utilization? ? What Are The Challenges to Lunar Mining? ? What is NASA Currently Doing?

May 1, 2009

By John Dean Smith

In order to discuss problem solving techniques for the future. we must first review the past. This paper will discuss the drilling and blasting problems and techniques that were used by .Imax Coal in the past few years, tn those of today.

Jan 1, 1991

With only one certain exception coal was never used by the Indians, before white men came to America, for any purpose except as an ornament or for paint. Within the past few years it has been discovered that the Hopi Indians in Navajo County, Arizona, used lignite for burning pottery, about 1000 A. D., as dated by tree rings. They were able to obtain a clear color in their ware that could not be obtained with brushwood fires. The coal was mined by hammers from outcrop openings, some of which can still be seen, and the tools used have been found in them.1 (See also p. 376.) Small figurines made of splint or cannel coal have been found at various localities in western New York, in Ohio and possibly other places, evidently made for ornaments. There is no reason to think they are of any greater age, if as old, as that mentioned above. Some crushed coal was used by the Indians as a black pigment in painting themselves, but apparently the eastern Indians never used coal for any other purposes. Some think that several tribes of Indians in the Northwest, along the Missouri, used coal as fuel, the basis being a statement attributed to Radisson about 1660. In the Jesuit Relations of 1659-1660 it was stated that Radisson anti Groseilliers had just returned from a visit to Lake Superior and beyond. "In the country of the Poualak, which means 'warriors' they say `as wood is scanty in supply and small in size in their country, nature has taught them to make fire with coal from the earth (charbon de terre) and to cover their cabins with skins.'"2 This statement was only hearsay with the good fathers, and the reputation for veracity of the two explorers is not of the best, and it is extremely probable that instead of coal they used turf, dry grass or buffalo chips. In fact in Radisson's Voyages' he does not mention coal at all in his account of the third voyage, when he was supposed to have seen it used. His accounts of his travels are badly mixed, and he and his companions were much better travellers than narrators. None of the early travellers up the Missouri River saw any evidence even then that the Indians were familiar with the use of coal. In the writer's opinion it is unlikely that coal was used as stated by the Jesuits.

Jan 1, 1942