Search Documents

By D. Ingram

"PRIMARY DUST COLLECTOR A. 42,000 CFM James Howden Fan Z-6 Size 3650 Fan Dia 40"" HP 75It was found that the fan was not large enough to remove the air that was displaced by the trucks dumping. So it was removed and an enclosure was installed to isolate the gyro from the rest of the building.B. FANSJames Howden Fans Model RPM 3500 Series 357 FW HP 10These fans were installed when the first dust system was put into operation. It was found that the high RPM and extreme fan wear caused a major maintenance problem. These fans were replaced with Chicage Blowers Model SWS1 RPM 1180 Dia 36"".DRY CYCLONE COLLECTORS A.,Three four foot rubber lined cyclones. Four six foot rubber lined cyclones.All under flow. Water is controlled manually and gravity flows to a central sump box. From there it flows to the grinding circuit in the Mill.Cyclone under flow product runs between 100 and 200 tons of dust per 24 hours with a screen analysis 30% + 400.The cyclone under flow product is diluted to about 3 to 4%. Solids total gallonage approximately 400.B.,Elbair Wet Scrubber125 HP RPM 56042,000 CFM,Model PX861The Elbair collects the total product from the discharge. Of the Cyclone fans the under flaw goes to the Mill - the Elbair discharges stack goes to atmosphere.The Elbair wet scrubber had to be redesigned in order to keep it in service."

Jan 1, 1976

By F. C. Lendrum

"This paper had its origin in a panel discussion organized by the Canadian Uranium Producers Metallurgical Committee (CUPMC) at their Annual Meeting in Blind River in May, 1964. The reason for the panel was the formation of the National Uranium Tailings Research Program funded in the amount of ten million dollars by the Federal government. According to the bureaucrats in charge the program would seek to solve the perceived problems as well as any actual problems they believed existed with uranium tailings. Dr. Allan Ashbrook of Eldorado Nuclear chaired this panel and his summation of the panel's purpose was set out as ""Regulation and the Regulatory Process in the Nuclear Industry, Where Have We Been, Where Are We Now and Where Are We Going""?"" This paper will try to relate these questions to the whole mineral industry.The Canadian Mining Association has been telling us our natural resources are today required only if they are competitively priced with those produced in so called ""third world"" countries where labour rates are lower, environmental restrictions may be less and every effort is made by the local government to sell their product. It is in this hostile economic climate that the Canadian mining industry now finds itself. Before going further I want to stress these comments apply only to: a) Mines financed by private capital in a free enterprise society.b) Mining companies want to operate in an environmentally safe manner. However, they must earn a profit because no company financed with private capital can borrow money ad infinitum.WHERE HAVE WE BEENNone of us today would want to return to the days when the mill waste management system consisted of pumping the tailing to the nearest slope and letting nature's law of gravity do the rest. This was the way it was in early gold mines in Nova Scotia, tin mines in Cornwall, England or silver mines in Cobalt, Ontario and survives today in countries where climate, customs and methods of doing business are far different from Canada. As mill tonnage rates increased, more sophisticated systems evolved often designed for mining areas with different climates. Systems imported from arid climates such as south-west United States retained the solids but allowed bacterial oxidation of the sulphides promoting acid drainage. Environmental regulations were introduced and Canadian mines learned to handle tailings in our climates."

Jan 1, 1986

By Alexandre Aparecida Morais

No Lingotamento Contínuo de Planos (placas de aço) o número de corridas realizadas em um único distribuidor é um indicador de performance operacional de enorme relevância para a sustentabilidade do processo. Ligados ao desempenho deste indicador estão os resultados de índices como produtividade, redução de custos, segurança e qualidade. Buscando melhorar este indicador a ArcelorMittal Aços Planos América do Sul – Unidade Tubarão iniciou no final de 2012 um projeto multisetorial subdividido em vários subprojetos satélites para aumentar o número de corridas em um único distribuidor visando obter ganhos nos índices técnicos descritos anteriormente. A proposta de meta oriunda deste projeto visava aumentar em no mínimo 70% os valores médios de corridas em um único distribuidor no Lingotamento Contínuo de Placas, o que representaria ganhos superiores a 1,2 milhões de dólares por ano. Neste trabalho é apresentada a metodologia definida para o projeto com suas respectivas etapas, o resumo de alguns subprojetos de sustentação e os resultados que já foram atingidos.

Aug 16, 2017

By J. F. Stenebråten, W. P. Johnson, D. R. Brosnahan

Carbonaceous material (CM) from ores of varying preg-robbing activity from Barrick Goldstrike Mines Inc. (BGMI), Nevada, was characterized in terms of its functional group content, hydrocarbon content, elemental composition, and humic acid content. FT-IR analyses showed neither the presence of hydrocarbons nor of carboxylic, phenolic, or sulfhydrol functionalities. FT-IR bands present included C=C stretching in aromatic rings and C-O-C stretching, indicating presence of oxygen as ether linkages in the carbon matrix. Calculated atomic oxygen to carbon (O/C) ratios did not reveal a trend between maturity of CM and preg-robbing behavior, possibly due to low resolution of electron microprobe analysis. However, the atomic O/C ratios agree with other chemical analysis, indicating that the organic carbon is very mature, similar to or higher in grade than anthracite coal.

Jan 1, 1999

By Tormod Forland

FROM equilibrium measurements on the system NaF-Na 3A l Fo-A 1 2 O 3-Na CO 3-CO 2 with high contents of NaF, Forland, Storegraven, and Urnesl concluded that complexes are formed containing two oxygen, three aluminum, and a less defined number of fluorine per complex. The same number of oxygen atoms per complex was also found by cryoscopic measurements for mixtures high in NaALF 6. In a recent paper by Stokes: some other complex ions, Al2O2F42- and AlOF2-, have been suggested. Here an additional argument in favor of the complex ALO2F. suggested by Forland, Storegraven, and Urnes will be given. When fused Na3AlF6 containing some A12O3, is cooled slowly, the solid phase will consist of the two components as separate phases. The melting point and the heat of fusion of Al2O3 are so high that this component will form the stable solid phase even though in the liquid state the complex may have a high stability. If, however, the fused mixture is quenched, the decomposition of the oxygen-containing complex and the formation of solid Al2O3 does not proceed fast enough, and a solid solution of A12O3 in Na3AlF6 is obtained. Zintel and Morawietz3 obtained cryolite containing 10 pct AL2O3 in this way. The density and the lattice parameters of the A12O3 containing cryolite were also measured, and from this it was concluded that the Al2O3 enters the cryolite lattice as Al3AlO0 groups replacing Na3AlF6 groups. However, the experimental data could as well be explained by assuming that one Na+ ion and two of its neighboring F- ions are replaced by one Al3+ ion and two O2- ions. This may be pictured schematically as: F F F F F F F Al F Na F Al F ,-Na+ + Al8+ F Al 0 A1 0 A1 F F F F —2 F- + 2O2- F F F solid cryolite cryolite-alumina solid solution This means that the complex in the solid solution, derived from X-ray and density measurements, is the same as that which Forland, Storegraven, and Urnes derived from equilibrium measurements in the liquid state. References IT. Forland, H. Storegraven, and S. Urnes: Ztsch. fur anorgan-ische und allgemeine Chemie, 1955, vol. 279, p. 205. 2J. J. Stokes: AIME Trans. To be pubhshed. s E. Zintel and W. Morawietz: Ztsch. pubhshed.fur anorganische und allgemeine Chemie, 1939, vol. 240, p. 145.

Jan 1, 1958

By D Woolmer

Since January 2019, BHP Olympic Dam have been trialling the use of a drone based LiDAR mapping system for the purpose for surveying stope voids. This new technology utilises Simultaneous Location and Mapping (SLAM) algorithm providing positioning, stability and collision avoidance in GPS denied environments. Implementation of this system utilised underground personnel trained in the equipment’s use. The study’s intention was to evaluate the effectiveness of this equipment versus traditional surveying methods in regards to quality, safety and productivity. The trial results showed a marked improvement in the quality, productivity and personnel safety when conducting surveys. The use of the drone and LiDAR system reduced personnel and equipment requirements for surveys, thus allowing these resources to be deployed elsewhere. The technology’s simple and rapid deployment allowed multiple surveys to be conducted during a 12 hour shift, including ad-hoc work with minimal disruption to underground operations. After the drone’s initial trial, further work was conducted to utilise the Hovermap LiDAR scanner on other platforms to increase utilisation. A mounting system was created allowing the LiDAR to be mounted on a remotely operated loader or vehicle. This enabled drawpoint scans to be taken directly after production completion, resulting in faster stope close outs and drive scans for convergence monitoring. Implementation of the LiDAR system has resulted in improvements in the stope production cycle by reducing delays previously associated with data capture. The increase in the volume and quality of data has also allowed in-depth back-analysis of stopes in new mining areas to be conducted, which have driven improvements in the design process.

Mar 15, 2021

By Peirong C, Pei N, Shouxi H, Hongzhong X

Indosinian (T) orogeny amalgamated the Mongolia-Xingan fold zone, the North China continent, the Yangtzi platform and the SE China fold zone into a unified continent. The early to middle Yanshanian (J-K,) orogeny created a Cordilleran type active continental margin in East Asia, reactivated the consolidated East China continent, and generated a large amount of granitoids, calc-alkaline volcanics and W, Sn, Mo, Cu, Au, and U ore deposits. The late Yanshanian (K2) orogeny began a transition to the western Pacific type continental margin. A tensional environment led to the development of peralkaline magmatism and the formation of continental basins with red beds. The Himalayan (Tr-Q) orogeny was characterised by a backarc spreading and rifting regime. The dominant magmatism was continental basaltic.

Jan 1, 1995

By Tetsuo Yamazaki

Metal market prices rose drastically in 2006, and most broke historical records as shown in Figs. 1-4. This increase has been basically driven by economic growth in Asian countries, especially China. The growth trend is expected to continue for several years. Then, India will follow the same growth trend. Their metal demands keep the price levels high for 20 years or more. One more additional important factor on the metal market prices is hedge funds come into the market. Japan imports all metals for domestic use from overseas. The amounts imported were 1.27 million tons in copper, 0.32 million tons in lead, 0.59 million tons in zinc, 0.20 million tons in nickel, and 1.18 million tons in manganese, respectively in 2006 (Source: http://www.jogmec.go.jp/j_resourse/index.html#03). Though mainly we import the concentrates and our domestic customer smelters take the part of metallurgical leaching, the payment necessary for purchasing the concentrates is estimated about US$ 10 billions in 2006. The payments in 2005 and in 2003 were about a half and a quarter of the 2006, respectively. Japan must have effective counter measures to reduce the future payments.

Sep 24, 2006

By George F. Kunz

THE recently discovered occurrence of diamonds near Murfreesboro, Pike county, Ark., was brought to. our attention by Mr. Samuel W. Reyburn (Trustee for Messrs. C. S. Stifft, A. D. Cohn, August Zinsser, Jr., and himself, owners of the property), through whose courtesy we investigated the locality of the deposit. Prospecting with the diamond-drill is now in active progress ; but mining operations on a large scale have not yet been ordered. Geology.-The geology as well as the petrography of this interesting locality has been well described by Messrs. J. C. Branner and R. N. Brackett.1 Briefly summarized, the igneous rock in which the diamonds are found is a vitreous peridotite, forming a stock or volcanic neck, which has broken up through the Carboniferous and Cretaceous quartzites and sandstones. After an extensive period of erosion, during which an unknown portion of the neck and presumably a previously existent volcanic cone have been removed, the surface was covered with thin beds of Post-Tertiary conglomerate. The volcanic intrusion was accompanied by the formation of several small dikes of a rock much like that of the main body. One of these dikes cuts across the stock, while another cuts the Cretaceous sandstone, but is overlain by the conglomerate, thus giving a datum for the period of intrusion. So far as known, there was little, if any, metamorphism of the country-rock by the igneous magna, which probably followed an approximately vertical course, so that a more or less vertical extension downward of the igneous body to indefinite depths may be expected.

Mar 1, 1908

By Bradford C. Wesstrom, Ricardo Parra

The Freeport McMoRan El Paso Refinery uses co-generation to produce some of its electricity and all of its steam. This paper will cover the operation of the co-generation plant natural gas turbine at a fixed RPM for blade longevity and energy output. The by-product heat from the turbine passes through boilers with additional heat from a duct burner to produce steam for the Tank House and auxiliary operations. The steam demand varies dramatically throughout the day based on unloading activities in the Tank House. The use of an automated steam control system within the El Paso Refinery will help stabilize line pressure by incrementally controlling steam consumption based on electrolyte temperature. This will minimize steam line pressure fluctuations. INTRODUCTION In the mid 1920’s the Nichols Copper Company of Laurel Hill, New York recognized the need for a modern copper refining facility in the southwest. Due to the many railroad heads, affordable power and abundant labor supply, and the close proximity to regional copper smelters in Mexico, Arizona, and New Mexico, El Paso became the logical location. In December 1928, ground was broken for the joint venture refinery between the Nichols Copper Company, Phelps Dodge, and the Calumet and Arizona Mining Company. In September 1930, Nichols Copper Company became a part of Phelps Dodge Corporation after a stock exchange. In July 1938, Nichols Division officially became Phelps Dodge Refining Corporation. In March 2007, Freeport McMoRan Copper & Gold acquired Phelps Dodge. Energy costs (electrical and thermal) are critically important in the viability of modern copper electrorefineries. The El Paso Refinery produces electricity and steam through its cogeneration system. The El Paso cogeneration facility is a natural gas, 15-megawatt facility containing five turbine generators and associated waste heat recovery boilers. The facility is divided into two phases. Phase I consists of two Allison 2.2-megawatt turbine generators. Phase II consists of three Solar Taurus 3.5-megawatt turbine generators. Presently three units in Phase II are operated. The Phase I units were purchased and installed in 1986 and the Phase II units in 1992 (Solar 1991). The facility operated at full capacity until 2003 when steam demand was significantly reduced due to decrease in cathode production and closure of the copper sulfate and precious metal operations. Phase I units were taken out of service and put on care and maintenance status.

Jan 1, 2019

By Murali Gadde

The immediate floor bed in the Illinois Basin coal mines is often comprised of weak plastic underclay material. Operational and stability problems were encountered in the past due to the low strength characteristics of the underclay floor. Among several indicators of the nature of the floor, Atterberg limits are the most important ones that describe the plasticity behavior of these clayey materials. While several useful and interesting studies were conducted in the past on the Illinois Basin weak floor material, within the knowledge of the authors, a comprehensive database describing the plasticity characteristics of the floor material has never been published. In this paper, a large database comprising over 700 sets of Atterberg limits was put together from 39 inactive and active mines from all the three states covering the Basin. Analysis of this data shows several interesting trends related to the engineering behavior of the floor material. The paper also describes the practical implications of the trends shown by the Atterberg limits.

Jan 1, 2008

By W. H. Ode

Because trade increased among various nations after World War II, the Coal Committee of the Economic Commission for Europe established a Classification Working Party in 1949 to develop an International system for classifying coal. Although national classification systems existed, they had been developed in accordance with characteristics of domestic coals without reference to coals of other countries. Terms for describing similar or identical coals differed in each nation. This caused confusion in evaluating coals shipped in international trade and also hampered exchange of technical information on problems of coal utilization. Experts4/ participating in the classification project early in their work agreed that two systems should be formulated, one for the higher rank coals or so-called "hard" coals in European terminology and the other one for the lower rank coals, the latter designated mainly as brown coals and lignites in the various countries. Rank refers to the degree of metamorphism (progressive alteration) in the natural coalification series from lignite and brown coal to anthracite. The system for classification of hard coals was published late in 1956 as a document of the United Nations.5/ Results of a study for applying this system to American coals were published in 1958.6/

Jan 1, 1960

By Samuel Thomas

The specimen of anthracite coal which I hold in my hand, insignificant as it may appear to the casual observer, speaks volumes to me and to the initiated, as it suggests and represents the entire evolution of the use of anthracite coal in the manufacture of pig-iron, the growth and development of which it is my purpose to review here to-day. During our recent visit to the Mountain Copper Co.'s works at Keswiek, I picked up this piece of coal from a pile of anthracite lying in the yard, asked Mr. Edwards, the manager, a countryman of mine, where it came from, and, to my surprise and delight, discovered that it had been brought all the way from Wales, and had come out of the identical vein which my father opened near Yniscedwin, about eighty years ago. I had no idea, before this incident, of contributing to the already full and complete programme of the day; but, being requested by our distinguished President and Secretary to do so, I consented to relate here the story which this remarkable find naturally brought back to my mind.

Jan 1, 1900

By Daniel Hodouin, Claude Bazin

"A graphical method to assess the size reduction by grinding is presented and illustrated with data collected from laboratory grinding tests and industrial grinding circuits. The method lies between the graphical comparison of size distributions and the population balance model. The method is easy to apply and provides a quick way to compare grinding mill performances under various operating conditions and processed ores. The application of the method to industrial mills shows that a grinding mill operation could present an invariant behaviour that can be exploited for simulation purposes.INTRODUCTIONThe size reduction of particles by grinding has been studied for decades and several books were published on the subject. Most of the recent studies focus on the modelling of the ball, semiautogenous and autogenous grinding mills operation (Napier-Munn et al., 1996) because accurate simulators can be used for design, optimization and control. Although the development of realistic simulators is progressing, the trial and error method is still used by many operators to identify optimum operating conditions for a grinding machine.Laboratory tests allow the characterization of the material submitted to grinding and the analysis of various operating conditions, such as ball size or shape, mill speed and slurry concentration of solids, on particle size reduction. Similar tests can be conducted in a plant, but results are often difficult to analyze due to errors associated with sampling and sensor accuracy. This paper presents a graphical method to assess the degree of size reduction carried out by a grinding machine. The paper consists of three sections. The first section describes the method and the following sections illustrate the method with data taken from laboratory and industrial grinding machines."

Jan 1, 2004

By G. W. Jones

From evidence made available during the investigation, it was concluded that the first of a series of explosions occurred at 1:15 to 1:20 p.m. September 21, 1951, in an underground vault that housed pressure regulators on the gas-distribution lines that served Brighten. This explosion damaged the pressure regulators and permitted high-pressure gas to enter the distributing mains and individual-service lines. As a part of the gas-distribution system was not provided with means for protection against such excessive pressures, gas gained access to the interiors of many residences in this area and caused a series of disastrous explosions and fires, which took place during a period of approximately 2 hours after the initial explosion in the pressure-regulator vault. Two persons were killed in the first explosion in a residence, and a third person died of a heart attack attributed to the excitement that prevailed during the explosions and fires, Twenty-three persons were listed as injured. Forty-one residences were either destroyed or damaged - 11 by explosion and the remainder by fires, which developed as a result of gas leakage into residences. Fifteen residences were listed as "completely down" or "gutted." Unofficial estimates of property damage ranged from $1,000,000 to $1,500,000. In view of observations made and information obtained during the investigation, recommendations are presented in this report relative to the natural-gas distribution system in Brighton, which may be helpful in the prevention of similar accidents in this and other communities.

Jan 1, 1952

By Carle Hayward

SULPHUR has long been one of the banes of the steel manufacturer and often no effort and expense have been spared in order to reduce it to a small per cent. in the finished product. This condition is clue to a general conviction that in many cases where steels have failed in service, sulphur has been the cause. But there has been a growing feeling in recent years that the verdict against sulphur has been unnecessarily severe. In cases of segregation it was present in augmented amounts along with other impurities, but it had not caused the segregation. High sulphur in pig iron is caused by poor furnace conditions and the sulphur is merely one indication of an iron that has not been properly reduced. No amount of subsequent treatment under oxidizing conditions in the open-hearth furnace can remedy the defects, although the per cent. of sulphur may be considerably reduced. In other words, the causes of bad steel can frequently be traced back to bad pig iron, and sulphur is merely one indication that the pig iron is bad. The writer recently visited a steel plant where a mass of evidence had been accumulated which substantiated this fact, and the superintendent was .emphatic in stating that high sulphur was not harmful provided the steel was not otherwise poor due to insufficient reduction in the blast furnace. The presence of a moderate amount of sulphur is desirable from the standpoint of the man who machines the steel. The low-sulphur material drags and the production of a smooth surface is very difficult. A slight increase in sulphur enables the machinist to produce a smooth surface without difficulty. Since, therefore, such large quantities of steel are subjected to machining, it becomes highly important that the sulphur controversy should be settled, and if its presence is proved to be harmless the ban on it should be lifted.

Jan 10, 1916

By Arturo Ressi di Cervia

Construction of the drilled shafts for the Brightman Street Bridge Replacement Project were not only challenging due to working over the water but were also challenged by changed soil conditions, concurrent work being performed by an adjacent contractor on the same project, environmental restrictions and severe winter conditions. A total of 36 x 8 feet diameter drilled shafts with 7.5 feet rock sockets were installed for the East and West bascule piers. This project also included Osterberg Cell load testing on two production drilled shafts at each the East and West bascule piers. The results from the load test program were used to fine tune the design of the drilled shaft rock sockets. From a constructability standpoint the reverse circulation drilling method with a pile top drill rig proved to be an excellent choice for drilling the overburden and rock sockets of the large diameter deep drilled shafts.

Jan 1, 2003

By S. Belair, V. Weigel

As a growing mining company, ERAMET is looking for new positions on the strategic metals market. In this context, the Gabonese Maboumine pyrochlore deposit is currently being studied for the recovery of niobium, tantalum, rare earth elements (REE), and uranium. This ore shows mineralogical and chemical characteristics that make it challenging to process by already known practices, from both technical and economic points of view. In this context, ERAMET has developed since 2008 an innovative hydrometallurgical process which has been successfully operated at a pilot plant scale. While the upstream part of the process aims to dissolve the valuable elements in sulphuric acid, the downstream part of the process aims to recover them separately in a marketable form. The focus here will be on the recovery of the REE. The ore deposit contains approximately 1.4% of REE including 87% of light REE and 13% of medium-heavy REE. The challenge in this process lies in the fact that the major elements in the matrix are iron and aluminum. An innovative process has been developed in order to recover all of the REE in these unfavourable conditions, described in this paper.

Jan 1, 2014

By J. D. Bittner

The ST separator utilizes electrical charge differences between materials produced by surface contact or triboelectric charging. When two materials are in contact, material with a higher affinity for electrons gains electrons and thus charges negative, while material with lower electron affinity charges positive. This contact exchange of charge is universally observed for all materials, at times causing electrostatic nuisances that are a problem in some industries. Electron affinity is dependent on the chemical composition of the particle surface and will result in substantial differential charging of materials in a mixture of discrete particles of different composition. In the ST separator (Figures 1 and 2), material is fed into the thin gap 0.9 ? 1.5 cm (0.35 -0.6 in.) between two parallel planar electrodes. The particles are triboelectrically charged by inter-particle contact. For example, in the case of coal combustion fly ash, a mixture of carbon particles and mineral particles, the positively charged carbon and the negatively charged mineral are attracted to opposite electrodes. The particles are then swept up by a continuous moving open-mesh belt and conveyed in opposite directions. The belt moves the particles adjacent to each electrode toward opposite ends of the separator. The electric field need only move the particles a tiny fraction of a centimeter to move a particle from a left-moving to a right-moving stream. The counter current flow of the separating particles and continual triboelectric charging by carbon-mineral collisions provides for a multi-stage separation and results in excellent purity and recovery in a single-pass unit. The high belt speed also enables very high throughputs, up to 40 tonnes per hour on a single separator. By controlling various process parameters, such as belt speed, feed point, electrode gap and feed rate, the ST process produces low carbon fly ash at carbon contents of 2 % ± 0.5% from feed fly ashes ranging in carbon from 4% to over 30%.

Feb 27, 2013

By T. O. Dauda, L. O. Ojo

One of the results of the Earth summit (The United Nations Conference) on Environment and Development - UNDP is the statement of forest principles. Others include: the Rio Declaration which is that the human beings are entitled to a healthy and productive life in harmony with nature; Agenda 21-for achieving sustainable development in the 21st century; the convention on biological diversity and the frame work convention on climate change. In the preservation of the biological diversity, Government at various levels took series of steps such as legislation, establishment of forest reserves including strict nature reserves, Forest guards, afforestation projects and others. Omo Forest Reserves is one of the Forest reserves owned by the Ogun state Government of Nigeria. It houses the Omo Biosphere Reserve (that is Strict Nature Reserve of International standard). This biosphere reserve is surrounded by buffer zones, which are meant to serves as protection for the biosphere reserves against encroachments. This study showed that the richest plot in term of species composition (that is plot 15 with the species frequency of 123) is almost the least diverse (with Simpson diversity index of 0.9127 which is 0.0238 higher than the least). It could also be established from this study that the diameter size class of trees with the highest frequencies are the lower size classes (5cm-10cm and 10cm -20cm). These results revealed a magnanimous encroachment on the buffer zones, which is an indication of bad status for the Biosphere Reserves as well as against the spirit of the sustainable use of the natural resources.

Jan 1, 2005