Search Documents

By Tomohide Takeyama, Yuki Yoshida, Masaki Kitazume

"Abstract A series of centrifuge model tests was conducted to investigate the failure pattern and stability of cement treated clay ground having an unsupported vertical slope. The model ground was subjected to monotonically increasing centrifugal acceleration until it failed due to the enhanced self-weight. The test results were compared with the numerical analyses in which the treated soil was simulated by the Smoothed Particle Hydrodynamics (SPH) method. In the simulation, the Dracker- Prager model is employed as the constitutive model. In order to simulate the brittle behavior of the cement treated soil, it is assumed that the unconfined strength is gradually reduced to a certain value which corresponds to the residual strength due to accumulated plastic strain. It was found that the simulation by using SPH method can express the brittle failure observed in the centrifuge model tests.IntroductionBecause of economical and environmental concerns it has become more difficult in recent years to obtain enough soil to construct reclaimed land for airports, electric power plants, manufacture plants and so on. On the other hand, it has become difficult to find and construct disposal sites for waste subsoil or dredged soil. These circumstances have encourage geotechnical engineers at present to use these poor quality materials as filling materials more than they were used one or two decades ago. Several soil admixture methods have been developed to improve their properties and to manufacture high quality fill materials.The deformation and strength characteristics of cement treated soils have been investigated in Japan, which have revealed that the treated soil is characterized by a brittle behavior with quite high compressive strength and quite small strain at failure, and the treated soil with relatively high strength shows tensile failure instead of shear failure. Regarding to evaluate the stability of structures adjacent to or buried in the treated ground, Kitazume (1998) and Kitazume et al. (2003) investigated the earth pressure of cement treated ground by the centrifuge model tests. And they emphasized that the failure pattern of the cement treated ground was much different from that of ordinary ground. After the Hyogoken- Nambu earthquake in 1995, many design codes for the seismic stability were revised in Japan, so that seismic stability must be evaluated more precisely. The dynamic earth pressure of ordinary grounds is usually calculated by a pseudo-static limit equilibrium method based on the Mononobe- Okabe’s method (Okabe, 1924; Mononobe and Matsuo, 1929). This calculation method is also applied to the cement treated ground, although its applicability has not been thoroughly clarified."

Jan 1, 2014

By J. W. Richards

Plating iron with copper has received great attention from practical and scientific men, but, aside from the deposit secured by immersion of iron in copper salts, by electro-plating, or by welding together thin sheets of iron and copper, these efforts have met with no success. Failure of these efforts, in the production of copper plating, has been due to the fact that the conditions normally and necessarily present in the plating operation are antagonistic to the production of copper-plated iron. In most, if not quite all of them, a bath of molten copper has been used. The temperature of a molten copper bath is so high that the iron becomes oxidized before it can be immersed in the molten copper, and unless a protective flux for the molten copper is used, the surface of the copper will become oxidized, and, in any event, the plated iron will oxidize immediately on its being withdrawn from the molten bath. I recently had the pleasure of visiting the works of The Metals Plating Co. at Elizabeth, N. J., where I witnessed the plating of iron sheets with copper by a new process.l The plating metal is applied to the sheet in the form of a liquid mixture by means of rolls, such as inking rolls. The sheet, after being coated with the mixture, is automatically carried forward and deposited on a link-belt conveyor, which carries it through a furnace maintained at a temperature well above that of molten copper. The basic principle involved in this method lies in the application of the plating metal to the sheet while the sheet is cold and then melting the metal in place on the sheet under conditions which are favorable to the formation of the plating. Plating Mixture The liquid plating mixture is composed of either copper oxide or finely divided copper, or a mixture of both, ground to the consistency of a light varnish in a crude oil having an asphaltic base, of a specific gravity of from 14" to 16' Be. The plating mixture which gives the best results

Jan 1, 1919

By J. D. Miller, C. L. Lin

In the processing industries, it is well known that particle shape is an important factor which determines the behavior of particulate systems. For example, system properties of technological significance including rheology, suspension stability, agglomeration, packing, permeability…etc, are affected by particle shape. In this regard, characterization and analysis of particle shape is essential for more detailed understanding and improved development of particulate processes. In general, it is clear that the behavior of these systems depends on the statistical characteristics of particle shape. Remarkably few techniques exist to predict the mechanical and hydrodynamic behavior of an irregularly shaped particle or a population of irregularly shaped particles for that matter. The lack of models and correlations can be attributed to the wide variety and complexity of particle shapes, the difficulty of defining shape descriptors suitable for modeling, the limitations of measuring shape, and the lack of classifying techniques to characterize particle shape. In this paper, we present information on how 3D particle shape can be measured, characterized, and analyzed using cone-beam X-ray microtomography (XMT).

Jan 1, 2005

By S Sullivan

The key skills for a competent geologist are observation, documentation, analytical thought and the ability to communicate. These attributes have served the geological world for the past two centuries since the field of geology was separated out from natural philosophy. The understanding of the structural setting, lithologies, alteration and 3D distribution of the target mineral species are essential precursors to resource evaluation and potential economic extraction. The advent of artificial intelligence and machine learning has matured to the point where observation by dedicated sensors and analysis by customised AI algorithms can replace manual processes and deliver credible results. In combination with analytical data such as assays, various sensors now collect physical properties of rocks which are used as proxies for mineral identification and rock mass classification. These sensors include X-ray and infra-red spectra, magnetic susceptibility, gravity/density, EH/pH measurements, conductivity, colourimetric readings, porosity, fracturing and fracture intensity. Analysis using machine learning techniques trained using known data sets can determine rock type classification, rock density, quantification of grade/quality attributes, mineral alteration, weathering and geotechnical attributes such as rock quality. This type of data relies on calibration and quality control of a variety of different types of electronic hardware. The resulting data is non-additive, has error ranges and will be suitable for consumption by fast AI methods providing probabilistic analysis. A second stage could include geometallurgical constraints to provide an ‘extractability index’, which is of more interest to miners than pure geotyping. Using resultant interpreted geological criteria, 3D domain models with spatial attributes will be built.

Sep 1, 2024

By S. J. Schatzel, W. P. Diamond

High methane emissions originating from the active face areas and from the fractured formations overlying and underlying the mined coalbed can adversely affect both safety and productivity in underground coal mines. Since ventilation alone may not be sufficient to control the methane levels in the longwall mining environment, gob gas ventholes have become a standard supplementary methane control option in many mines. As mines progress into deeper and gassier coalbeds, or as longwall panel size increases, ventilation and gob gas ventholes together may not be sufficient to maintain methane levels within statutory limits. To decrease the risk associated with methane emissions under these circumstances, in-seam horizontal methane drainage is often used to reduce the gas content of the coalbed prior to mining. Horizontal methane drainage borehole completion designs, drilling strategies, and degasification lead times may need to be adjusted for site-specific conditions due to mine design, geology, and the gas content of the coalbed. This study investigates different horizontal methane drainage borehole patterns, borehole lengths, and degasification times prior to and during panel extraction to evaluate their effectiveness in reducing methane emissions using a "dynamic" 3D reservoir modeling of a 38 1-m wide longwall panel operating in the Pittsburgh coalbed. Results of this study showed that dual and tri-lateral boreholes are more effective in decreasing emissions and in shielding the entries compared to fewer shorter, cross-panel, horizontal boreholes parallel to the longwall face. Modeling results showed that after 12 months of pre-mining methane drainage, the average longwall face emission rates can be reduced by as much as 10.3 m3/min and 6.8 m3/min using tri- and dual-lateral boreholes, respectively. It was also shown that if pre-mining methane drainage time is short, it is important to continue methane drainage during the panel extraction to maximize reductions in longwall face emissions since additional face emission reductions achieved during this period can be comparable to pre-mining degasification.

Study on Ball Mill Grinding of a Cassiterite-Polymetallic Sulfide Ore

Sep 13, 2010

By N. Anacleto, S. Ganguly

Reduction of Groote Eylandt (Australia) and Wessels (South Africa) manganese ores using CH4-H2-Ar gas mixture was investigated in a fixed bed laboratory reactor in the temperature range 1000?1200oC. The extent and kinetics of manganese ore reduction as a function of gas composition and temperature were determined by on-line off-gas analysis using mass-spectrometer and dew point sensor. Morphology of ores and its change in the course of reduction was examined by optical and scanning electron microscopy. Phases of raw materials and reduced samples were analysed by XRD and EPMA. Manganese oxides were reduced to carbide Mn7C3. High extent and rate of reduction by methane-containing gas in comparison with carbothermal reduction were attributed to high carbon activity in the reducing gas, which was in the range 15 - 50 (relative to graphite). The reduction rate of Wessels manganese ore increased with increasing temperature. Reduction rate and extent of Groote Eylandt manganese ore achieved maximum at 1050oC. The decrease in rate and extent of reduction of Groote Eylandt ore at higher temperatures, particularly at 1150-1200oC, was due to sintering and formation of semi-liquid silicate slag. The optimum conditions for the reduction of manganese ores were established as follows: a) temperature: 1150-1200oC for Wessels and 1050-1100oC for Groote Eylandt ores, b) methane concentration: 10-15 vol%, c) hydrogen concentration: above 30 vol%, (d) size: 1-3 mm. An addition of lime (10-15 wt% CaO) to the Groote Eylandt manganese ore increased melting temperature of slag and significantly increased the rate and extent of reduction at elevated temperatures.

Jan 1, 2004

By Randal Martin

Recently, questions regarding the influence of atmospheric temperature and humidity levels on airblast levels have arisen at a number of blast sites. Humidity is alleged to have contributed to high levels of disturbance within communities surrounding blasting. In some cases, local regulatory agencies considered adopting guidelines to specify humidity and temperature ranges under which blasting cannot take place. However, it is normal blasting industry practice not to consider humidity or temperature effects, in the absence of inversions, on airblast levels. When blasting is conducted in the vicinity of residential structures, the influence of weather on the propagation and attenuation of airborne noise from the blasting site is always a concern. Sound naturally attenuates in air with distance from the source. A part of this attenuation is attributed to divergence at the airblast wave front, while the remainder of the attenuation is an accumulation of various factors that include temperature and barometric pressure, absorption in air due precipitation and vegetation, wind and temperature gradients, atmospheric turbulence and topography (Beranek, 1971). Wind speed and wind direction, as well as vertical and horizontal temperature gradients can cause airblasts to focus in local regions surrounding blasting operations and may result in air pressures greater than expected. In fact, wind and temperature inversions can actually increase sound levels with distance from the blast site. Close to the blast site, the effects of inversions may be negligible but may exceed 10 dB at 800 m or greater (Davis and Cornwell, 1991).

Jan 1, 2001

By S. W. Stogran

"Chemical and limited biological monitoring of mine and mill effluents are being used by regulatory agencies to monitor and control discharges to the environment. Amendments to the Federal Fisheries Act may make it mandatory for mines to conduct Environmental Effects Monitoring (EEM) which will change the emphasis from monitoring effluents to monitoring impacts on receiving waters. The EEM amendments may expand the scope of present environmental studies to include: effluent mixing zone delineation; inventory and classification of resource, habitat, and historical receiving environment; effluent quality determination; chronic and acute bioassay testing; tissue analysis; benthic invertebrate monitoring; fish population surveying; fish tainting evaluation; and the evaluation of impacts on fish habitat, invertebrate communities and fisheries resources. The requirements for EEM have not yet been worked out by the mining industry and the government committee. Experience at Lakefield Research in conducting biological monitoring studies for the mining industry has shown that biological monitoring may be useful for assessing environmental impacts only if programs are planned and executed to collect relevant data, thus minimizing costs and maximizing effectiveness.IntroductionThe chemical monitoring of effluents and water bodies receiving effluents is common practice in the Canadian mining industry and has been used routinely by regulatory agencies to control discharges to the environment. Biological monitoring has also been used on a limited basis, primarily to augment chemical data collected. A number of regulatory bodies, primarily in Canada and the United States, have been incorporating biological monitoring into environmental regulations.Various forms of biological monitoring techniques have been used in Canada and the United States to help assess the impact of mining operations and effluents on the environment. Biological monitoring includes a wide range of activities, from monitoring metal uptake in individual organisms to examining the population dynamics in ecosystems. The most commonly employed biological monitoring techniques are the chronic lethality toxicity tests. Also becoming widely used are in situ and chronic toxicity tests."

Jan 1, 1994

By N. J. Tannyan

Laboratory bath smelting tests were conducted to determine the feasibility of smelting nickel- copper concentrate directly to a low iron matte in one step. Concentrate, air/oxygen and a silica flux were fed to a matte-slag bath kept in MgO crucibles at 1300°C. Various oxygen enrichments and smelting rates were used to maintain 0.5 to 2 wt"10 iron in the product matte. The slag losses are comparable to those obtained under similar industrial conditions. Due to the highly oxidizing conditions required to produce mattes with low iron contents, it is not recommended to target iron contents below about 2% in the matte. The specific bath smelting rates were equal to or higher than those in various industrial bath smelting processes.

Jan 1, 2003

By A. Golshani, M. Oda, K. Suzuki, T. Takemura

Anisotropic behaviours of OhshimaOshima granite were investigated by carrying out uniaxial compression tests, together with observations of microcracks under an optical microscope. The elastic modulus tensor of Oshima granite at 10 per cent strength,E10, were calculated using theoretically formulation of elastic modulus tensor in terms of the second-rank crack tensor for pre-existing open microcracks. Furthermore, with the assumption of orthorhombic elasticity, the nine moduli of Oshima granite E10were determined by uniaxial compression test. Twenty-onemoduli of samples, calculated without assuming any symmetry, also showed orthorhombic features. Direction of the symmetry axes agreed well with the orientation of preexisting cracks. Comparison of crack tensor-based formulation results with the experimentally determined one show that the anisotropy of elasticity of Oshima granite is caused by pre-existing open microcracks, not by pre-existing healed microcracks and also crack tensor formulation can be used, as a first-order approximation at least, to describe the anisotropy of Oshima granite induced by pre-existing open microcracks. ZUSAMMENFASSUNG: Das anisotrope Verhalten des Oshima-Granits wurde mit Hilfe voneinachsigen Kompressionstests und durch die Betrachtung von Mikrorissen unter einem optischenLichtmikroskop untersucht. Das Elastizitätsmodul von Oshima-Granit bei 10 Prozent Kraft E10wurde berechnet, indem man die Formulierung des Elastizitätsmodultensors, ausgedrückt alsRisstensor zweiter Ordnung theoretisch auf bereits existierende Mikrorisse angewandt hat.Außerdem wurden die neun Module des Oshima-Granits unter der Annahme orthorhombischerElastizität E10mit einem einachsigen Kompressionstest bestimmt. Einundzwanzig Stichproben,die ohne die Annahme irgendeiner Symmetrie genommen wurden, zeigten ebenfallsorthorhombische Merkmale. Die Richtung der Symmetrieachsen stimmte mit der Orientierungbereits vorhandener Risse überein. Der Vergleich der Ergebnisse der auf dem Risstensorbasierenden Formulierung mit der experimentell bestimmten Formulierung zeigt, dass dieAnisotropie der Elastizität von Oshima-Granit von bereits vorhandenen offenen Mikrorissenverursacht wird, und nicht von vorhandenen vernarbten Mikrorissen, und dass dieRisstensorformulierung auch zumindest für eine Annäherung erster Ordnung benutzt werdenkann, um die durch vorhandene offene Mikrorisse induzierte Anisotropie des Oshima-Granits zubeschreiben. RESUME: Les comportements anisotropes du granit d’Oshima ont été étudiés en réalisant destests de compression simple, et en observant les microfissures au microscope optique. Le tenseurdu module d’élasticité du granit d’Oshima sous une résistance de 10 pourcents, E10, a été calculéen se servant de la formule théorique du tenseur de module d’élasticité basé sur le tenseur defissures de second ordre des microfissures ouvertes préexistantes. En outre, sur base del’hypothèse de l’élasticité orthorhombique, les neuf modules du granit d’Oshima ont étédéterminés par des tests de compression simple. Vingt et un modules d’échantillons, calculés endehors de toute hypothèse de symétrie, ont aussi montré des caractéristiques orthorhombiques. Ladirection des axes de symétrie correspondait bien à l’orientation des fissures préexistantes. Lacomparaison des résultats de la formule basée sur le tenseur de fissures avec les résultatsdéterminés expérimentalement montrent que l’anisotropie de l’élasticité du granit d’Oshimaprovient des microfissures ouvertes préexistantes, et non de microfissures préexistantes referméeset que la formule du tenseur de fissures peut servir, au moins comme première approximation, àdécrire l’anisotropie du granit d’Oshima marqué par des microfissures ouvertes préexistantes.

Jan 1, 2003

By V. H. Whihelm

Since 1935 California has enjoyed a remarkable cycle of discovery, which has placed the state in a very satisfactory position in regard to oil reserves. Most ol the geophysical plays have been drilled and it is possible that new discoveries must be made by the application of careful geologic and stratigraphic studies. During 1940 only one new field was discovered, which, although not of major importance, may lead to additional discoveries. During the year, 113 wildcats were drilled. New discoveries, extensions and a reappraisal of discoveries made in 1939 will not approximate over 50,000,000 bbl., as against an estimated withdrawal during the year of 224,000,000 barrels. Demand in terms of crude for 1940 was 632,000 bbl. per day as against 626,000 bbl. per day for 1939. Demand for gasoline was the same as in 1939, but the demand lor fuel oil increased 3.8 per cent. Compared with 1939, Japanese shipments decreased from 75,786 bbl, per day to 61,000 bbl. per day, but the balance of Pacific foreign shipments increased from 59,409 bbl. per day to 61,304. Total with-drawals from storage during the year will approximate 7,000,000 bbl., almost all of which is fuel oil. Drilling activity was slightly greater than in 1939 and accounted for 890 new producing wells as against 851 for 1939 (Table 3). Production averaged 611,900 bbl. per day as compared with 614.,842 bbl. per day for 1939. The productive acreage figure of the state was increased by 4000 through discoveries and extensions. New Discoveries Los Angeles Basin District Del Vdle Field.—Northwest of Newhall, where the first oil well in California was drilled, R. E. Havenstrite completed his Lincoln No. I well, flowing 390 bbl. of 50" gravity oil together with 7000 M CU. ft. of gas. Later the well was recompleted, after cutting off the gas, for 950 bbl. of 34" gravity oil. The type of structure from which this production is coming is a plunging anticline, complicated by faulting. The Lincoln No. I well uncovered approximately 180 ft. of net sand. This field contains a gas cap and its indicated productive area approximates 500 acres. An intensive wildcat drilling campaign is expected during this coming year in the district in the vicinity of the Del Valle field. Extensions and Deeper Sand Developments Los Ange1es Basin District Athens Field.—On the northwest plunge of the Athens structure, the Thorley Oil Co. completed its No. 12-1 well, flowing 250 bbl. of 3 2" gravity oil from a depth of 8097 ft. The area in which the well is located is complicated by faulting and it is impossible at this date to determine the importance of this deep-zone discovery.

Jan 1, 1941

By V. H. Whihelm

Since 1935 California has enjoyed a remarkable cycle of discovery, which has placed the state in a very satisfactory position in regard to oil reserves. Most ol the geophysical plays have been drilled and it is possible that new discoveries must be made by the application of careful geologic and stratigraphic studies. During 1940 only one new field was discovered, which, although not of major importance, may lead to additional discoveries. During the year, 113 wildcats were drilled. New discoveries, extensions and a reappraisal of discoveries made in 1939 will not approximate over 50,000,000 bbl., as against an estimated withdrawal during the year of 224,000,000 barrels. Demand in terms of crude for 1940 was 632,000 bbl. per day as against 626,000 bbl. per day for 1939. Demand for gasoline was the same as in 1939, but the demand lor fuel oil increased 3.8 per cent. Compared with 1939, Japanese shipments decreased from 75,786 bbl, per day to 61,000 bbl. per day, but the balance of Pacific foreign shipments increased from 59,409 bbl. per day to 61,304. Total with-drawals from storage during the year will approximate 7,000,000 bbl., almost all of which is fuel oil. Drilling activity was slightly greater than in 1939 and accounted for 890 new producing wells as against 851 for 1939 (Table 3). Production averaged 611,900 bbl. per day as compared with 614.,842 bbl. per day for 1939. The productive acreage figure of the state was increased by 4000 through discoveries and extensions. New Discoveries Los Angeles Basin District Del Vdle Field.—Northwest of Newhall, where the first oil well in California was drilled, R. E. Havenstrite completed his Lincoln No. I well, flowing 390 bbl. of 50" gravity oil together with 7000 M CU. ft. of gas. Later the well was recompleted, after cutting off the gas, for 950 bbl. of 34" gravity oil. The type of structure from which this production is coming is a plunging anticline, complicated by faulting. The Lincoln No. I well uncovered approximately 180 ft. of net sand. This field contains a gas cap and its indicated productive area approximates 500 acres. An intensive wildcat drilling campaign is expected during this coming year in the district in the vicinity of the Del Valle field. Extensions and Deeper Sand Developments Los Ange1es Basin District Athens Field.—On the northwest plunge of the Athens structure, the Thorley Oil Co. completed its No. 12-1 well, flowing 250 bbl. of 3 2" gravity oil from a depth of 8097 ft. The area in which the well is located is complicated by faulting and it is impossible at this date to determine the importance of this deep-zone discovery.

Jan 1, 1941

By V. A. Akinbinua

This work is intended to examine the relationship between rock fragments produced during compression tests using a soft testing machine, e.g. hydraulic press (the machine used in this work is Amlser rock testing machine), and the rock fragments size distribution produced by fragmentation of the same rock through application of explosive. The rocks tested are fine grained marble, medium grained tonalite and fine-medium grained granite, medium grained norite and medium grained gabbro. The rocks types are prepared according to ISRM methods to be tested for strength determination. The rocks are loaded at constant load until failure. The fragments resulting from the failure of each of the rocks types are collected for size characterization by sieve analysis. The same rocks tested under soft testing machine are also prepared into blocks of dimension 150 mm length x 100 mm width x 100 mm height for blasting by explosive application. Each block of the different rocks are drilled through with an 8 mm diameter drill to a depth of 80 mm. Each of the holes on the blocks is spaced from each other at 44.7 mm and with a burden of 28 mm. The holes therefore formed a rectangular blasting pattern. Each of the holes was charged with a 720 mg electronic detonator and fired instantaneously inside a cylindrical blasting chamber. After each shot, the fragments are collected for size characterization. The sizes distributions from blasting are compared with sizes distributions resulting from rock testing using the parameter Xc of the Rosin-Rammler distribution function (RR) and 75% cumulative percentage passing. The analysis and finding from this work is presented in this paper.

Jan 1, 2014

By N. S. Dalal, X. Shi

"This study reports a new property of the important NAD(P)H-dependent flavoenzymes, glutathione reductase, lipoyl dehydrogenase and ferredoxin- NADP oxidoreductase, that can catalyze a one electron reduction of metal ions such as chromium(VI) and vanadium(V). During the enzymatic reduction process, molecular oxygen is reduced to H2O 2 , which reacts with the reduced metal complexes to generate hydroxyl radicals. Since the hydroxyl radicals have been suggested to play an important role in Cr(VI) toxicity, this study provides a basis for a recent observation that Cr(VI) mutagenesis is strongly oxygen dependent. These results also point to an enzymatic pathway for the metabolism of some metal ions and concomitant generation of hydroxyl radicals. l. INTRODUCTIONThe purpose of this communication is to report that some important NAD(P)H-dependent flavoenzymes (glutathione reductase, lipoyl dehydrogenase and ferredoxin-NADP+ oxidoreductase) can catalyze one electron reduction of metal ions such as chromium(VI) and vanadium(V) and simultaneously reduce molecular oxygen to generate Hi02 and, eventually, the ""OH radical. This finding is significant because (i) the known substrates for the flavoenzymes are organic species and not metal ions, and (ii) the report on the enzymatic formation of the ""OH radical provides a new pathway for understanding the mechanism of genotoxicity of some non-ferrous metal ions. For example, it has been suggested that OH radical is likely to be the major species responsible for Cr(VI) genotoxicity [1-5). The 'OH radical is generated through the reaction of Cr(V) complexes with cellular Hi02 [4,5]. Cr(V) itself is known to be generated from Cr(VI) in various biological systems, in particular, microsomes [ 6), mitochondria [7] and mitochondrial electron transfer chain complexes [8]. However, no specific enzyme responsible for the Cr(V) generation has been identified except possibly glutathione reductase [4]. In this study we have used ESR and spin trapping techniques to show that the flavoenzymes can generate Cr(V) and provide a catalytic redox cycle for 'OH formation in such reactions. Herein we present our results on Cr(VI) and summarize those on other systems. Correspondence address: N.S."

Jan 1, 1990

By Ryan Marsters, Adam Pring, Robin Dornfest

Raw water supply in the central Rocky Mountains often relies on trans-basin conveyance. Many of these older diversions incorporate high-elevation, miles-long tunnels driven over a century ago in hard rock. Tunnels were excavated using conventional drill-and-blast mining and weak ground was supported by timber sets and other various means. Over time, timbers rot and fail, rock quality deteriorates, and the timbers are gradually replaced by more timber, steel patches and braces, formed concrete, rock bolts, split sets, shotcrete, and other means which are commonly applied over existing support, thereby reducing tunnel cross sections, obscuring previous support systems, and rarely addressing the failing rock itself, leading to further deterioration of both the rock and the existing support. Traditional investigation techniques to assess compromised areas are often unfeasible due to access, depth, rubble and voids behind weight-bearing existing supports, confined space, poor invert conditions, poor ventilation, and flowing water. This presentation will discuss design procedures for assessing obscured ground conditions, assigning support classes which accommodate for unknowns, and implementing contractual means to address inevitable surprises or quantity overruns. Case studies include raw water supply tunnels in the Rocky Mountain region constructed between early to mid-20th century.

Dec 1, 2022

Jan 1, 1996

By Leandro Echavarría

El presente texto describe el sistema epitermal de Arcata, situado en Arequipa, Perú. Arcata es un distrito epitermal de sulfuración intermedia rico en plata y metales base, cuya mineralización se hospeda en vetas de rumbo predominante noroeste y movimiento principal paralelo a la inclinación que forman una estructura de fosa (graben). Las vetas poseen texturas de relleno de espacios abiertos como bandeados costriformes, en cucarda, crecimientos en peine y brechas, con ganga de cuarzo, calcita, rodonita y rodocrosita. Por su parte, los minerales de mena más comunes son galena, esfalerita, calcopirita, con los metales preciosos hospedados en sulfosales de plata (pirargirita y tetrahedrita). Asimismo, se ha identificado una compleja secuencia paragenética con varios pulsos responsables de la mineralización económica.

Apr 22, 2003

By J. H. Schulman, M. H. Buckenham

R. W. Christy (Manager of Sales, Sanitary Engineering Equipment, Link-Belt Co.) and C.D. Rubert (Barrett, Haentjens & Co.) — Messrs. King and Schepman have presented an excellent paper which outlines the general practice in the design of thickener mechanisms. Lifting devices, controls, special applications and underflow pumping arrangements have been reviewed in detail. Pumping arrangements were illustrated which eliminate the need for an expensive tunnel beneath the thickener floor. Most of those illustrated have the common feature of a relatively long underflow suction line extending from the hopper floor to the pump located on the bridge at the periphery of the tank. The authors limit these arrangements to comparatively dilute or thin slurrys. It is implied that dense and coarse concentrates, which are difficult to pump, cannot be handled unless a tunnel is constructed. Fig. 1 shows an underflow pump arrangement which negates the need for a tunnel but which permits the operator to convey a heavy dense slurry. The pump is mounted directly on the fixed hoist platform and the impeller is located at the base of the steel center column. Priming water is not needed. The column

Jan 1, 1963

By W. L. Jacobsen, T. L. Dyer

Cortez Gold Mines completed a feasibility study for a new openpit gold mine in north central Nevada. The production schedule calls for a peak in material movement. This schedule is based on current operational efficiencies and equipment parameters observed at the company’s existing openpit operation. To mitigate risks of over/under predicting production, simulation modeling was used to validate the loading and haulage requirements during the peak production period. The advantage of simulation is the ability to provide a realistic model of a mining operation based on scheduled and unscheduled random events during the period under analysis.

Jan 1, 2007