Search Documents

By J. I. Mathis

"The failure that was utilized for developing this model was a double bench-scale failure, approximately 20 m in height, in the Misery pit at BHP Billiton’s EKATI mine site. The bench that failed was excavated in biotite schist. Due to previous problems with bench-scale toppling failures, this bench was excavated with a 70° inclined, 30 m deep preshear. Upon exposure, the wall was very clean with half-barrels commonly observed from the pre-shear operation.In August 2003, a bench failure of about 1000 t occurred in this pre-sheared biotite schist (Fig. 1). Upon examination it was noted that the foliation that paralleled and dipped at 70° into the face when excavated was approximately horizontal at the top of the failure (Fig. 2). While the failure mode itself appears complex, the failure was apparently driven by three factors:• a low-angle, low-frictional strength fault or discontinuity at the base of the failure area;• water either contributed meteorically from precipitation and/or from permafrost melt; and• foliation planes providing a viable toppling geometry once toe block motion began to occur.The above details are illustrated in Figure 3.After considerable thought and analysis, a model was postulated for the failure.It is thought that the entire failure had been triggered by displacement of a toe block (Fig. 4). This toe block is bounded on the back by foliation, the bottom by a low-angle, lowstrength fault, and the front by the bench face. Water pressures behind the bench face developed forces on the block as can be seen in Figure 5. These forces were sufficient to induce block motion. As can be seen in the relative shear strength diagram in Figure 6, only a small amount of water is necessary in the face to initiate block displacement. Note that in this figure, a simplistic piezometric pressure distribution was assumed."

Jan 1, 2004

By K. Gie Tan, Frank Wright

"Misty Mountain Gold Limited (MGL - TSE VSE, MGLCF - NASDAQ) of Vancouver, owns the Harmony Gold Project located in the Queen Charlotte Islands of British Columbia. The deposit contains a mineable reserve of 2.3 million ounces of gold, at a 1.2 g/t cut-off and an average grade of 2.1 1 g/t Au.Discovered in 1970 and frequently investigated by previous owners, full-scale production has not yet occurred because of the complex metallurgy of the deposit. Recent process studies that were completed in six months at Process Research Associates Ltd. (PRA) of Vancouver resulted in significant improvements to the project viability. The work involved detailed mineral processing studies aimed at achieving a marketable concentrate. An option for bio-oxidation and cyanidation to allow on-site dor6 production was also investigated.The main findings at PRA followed the front-end recovery of finely divided free gold (Au) by gravity concentration. Approximately 20% of Au reported to less than 0.2% of the mass, resulting in a grade exceeding 500g/t Au. The resulting gravity tailing provided a uniform feed for flotation evaluation. The optimization of this step allowed for a reasonable primary grind size of 80% passing (&) 50pm. Efficient slime’s rejection was made possible by flotation at a reduced pulp density, and pre-oxidized sulphides were reactivated with Na,S. The regrinding of the bulk flotation concentrate followed by up to five stages of cleaning resulted in a combined gravity + flotation product of 50g/t Au with 82% recovery in less than 4% of the feed mass.Further studies indicated that the flotation concentrate was amenable also to tank bio-oxidation. At 65% sulphide oxidation the gold recovery improved from less than 70% to 90% by cyanide extraction using CIL (carbon in leach). This compares to less than 45% gold recovery from whole-ore cyanidation in several previous studies. Heap leaching may also be considered for lower grade material. PRA’s methodical approach and consistent results dispelled the uncertainty about predicting the material behavior for the Harmony Property."

Jan 1, 2000

By R. M. Cox

The ground forces generated by a properly installed and tensioned mine roof truss assembly can provide permanent mine roof support, even in severe ground conditions, either by direct suspension of the rock loads within the potential failure zone above the mine opening or indirect reinforcement of the natural rock arch that tends to form within the immediate mine roof. Notable advancements in mine roof truss support systems hardware and design technology have occurred since the introduction of the in situ mine roof truss concept for permanent mine roof support in 1966. The systematic installation of mine roof truss support systems has proven to be a very effective method of mine roof control room and pillar mines under a wide variety of ground conditions, even in areas otherwise considered unmineable because of severe roof control problems. Properly designed mine roof truss systems have also been used for permanent support of mine slopes and haulage tunnels.

Jan 1, 2002

By V. T. Dow

In April 1957 the Bureau of Mines instituted a reconnaissance of titanium-and zirconium-bearing heavy sandstone deposits in the Four-State area of Utah, Wyoming, New Mexico, and Colorado. This report summarizes the study. Eighty-two deposits or groups of deposits, containing an estimated 27,920,000 tons of titaniferous sandstone, were examined in the Four-State area; 16 in southern Utah, 19 in Wyoming, 33 in New Mexico, and 14 in southwestern Colorado. The 16 deposits examined in Utah contain an estimated 1,043,000 tons with an average grade of 17.98 percent TiO2, 5.67 percent ZrO2, 20.98 percent Fe, and 0.09 percent equivalent Th02. The 19 deposits investigated in Wyoming are estimated to contain 21,873,000 tons of titaniferous sandstone having a weighted grade of 5.22 percent 702, 0.55 percent ZrO2, 24.8 percent Fe, and 0.01 percent equivalent Th02.

Jan 1, 1961

By M. Akser, M. Tomas

Six Sigma is a methodology that uses a structured and disciplined approach to improve process performance (higher throughput, better recovery, lower cost, shorter cycle time, etc.). Specially trained people called “black belts” lead and manage Six Sigma projects. Black belts, with assistance from their team, ensure that projects follow the DMAIC (define, measure, analyze, implement and control) process phases. Timely completion of each project, with measurable deliverables, is key to Six Sigma’s significant financial success. Implementation of Six Sigma has been growing in recent years in a wide range of industries. The heavy mineral industry, like many other industries, could benefit from what Six Sigma has to offer. Specific Six Sigma project examples are included from DuPont’s Heavy Mineral Production Plant in Florida.

Jan 1, 2005

By G. E. Jones, G. K. Hoffman

Through the USGS National Coal Availability pro-gram, two San Juan Basin studies have been completed. The study areas are in the northwest Bisti field, Fruitland Formation and in the eastern Standing Rock field, Menefee Formation. Original resources are 4.66 Gt and 3.46 Gt (5.14 billion stand 3.82 billion st), respectively, in the Bisti and Standing Rock areas. Bisti coal resources are greatly reduced by the Bisti-De-Na-Zin wilderness area (1.13 Gt (1.25 billion st)). Technological restrictions remove 31% from Standing Rock original resource. Available resources are 60% (2.79 Gt(3.07 billion st)) of the Bisti original resource and66% (2.26 Gt (2.49 billion st)) of the original Standing Rock resource.

Jan 1, 2000

Your assessment of the minerals business. I would first like to express our profound sadness and sincere condolences to the families of the miners who lost their lives in recent mine mishaps particularly in West Virginia, and other locations. Any loss is unacceptable. It is time to review and, if required, re-establish a rigorous health and safety agenda in the mines. It must involve a review of health and safety regulations. And innovative training methods for sensing, awareness and mitigation of health and safety hazards must be developed. As far as the minerals business is concerned, I am excited about the outlook for mining. Over the last 20 years, global demand for minerals has closely mirrored the growth of the gross domestic product. Minerals re-main a major part of the world’s economic foundation. And that will continue to be the case. It is no surprise that the fortunes of the mining industry rise and fall with general economic trends. Globally, mining has been strong — thanks to the explosive economic growth in Asia. The U.S. mining industry has performed reasonably well, with notable strength in the metals, coal and construction and aggregate areas and with some softness in the industrial minerals sector.

Jan 1, 2006

By Nuno Cruz, Saúl Rodríguez

"When executing offshore bored piles there are several specific factors and problems to consider in order to guarantee excavation stability. One of the methods employed to carry out this type of work consists in setting up a floating work platform, typically a barge, and implementing a soil stabilization system that combines a partial steel guiding casing with third generation polymeric drilling fluids. The main aspects to take into consideration when performing offshore pile boring works are soil stabilization, project design, work methodology and operational aspects. An example of a work methodology problem arises before any pile boring work takes place as the steel guiding casing contains water, sometimes salt water. What to do with this water in order to replace it by an adequate polymer fluid will determine the stabilization capacity as soon as the shaft advances below the protection of the casing. Another example of operational problem may derive from barge movements while executing boring activities. This study is the result of extensive field data collection and concrete logging analysis from marine projects using polymers in different continents. The bored pile stability target was set ranging between 2% to 15% of concrete overbreak. Values above 15% or below 2% mean that there is a stability problem. Then the off-target pile’s data is collected, analyzed and classified under categories. Thus, a direct correlation is established between the problem category and the final results. Modifying steps in the pre-established construction methods or operational variables guarantees target results without the need to replace the approved construction methods. As a general conclusion, the worldwide experience in large diameter marine works, allows to provide truthful information and solutions for these problems. In knowing how to follow a logical sequence of work and applying adequate work methodology will be the key for success.GENERALBackgroundTo carry out the drilling process of offshore bored piles there are two main options to take into consideration: drilling the pile by using full guiding casing until final depth; or using a combined system of partial steel guiding casing and support drilling fluids.The knowledge and situations described in this paper come from the experience acquired in different projects where the second method was employed. This construction method consists in installing a steel guiding casing by vibration and thus covering the water table and further stabilizing the soil below it with polymeric fluids until reaching the pile’s final depth. The Fig. 1 schematic shows an example of this method where H corresponds to the length of the steel guiding casing whereas the remainder of the shaft’s length is stabilized by polymer fluid. The entire bored length is full of slurry up to top of casing.In most cases this kind of civil works results from the need to build a bridge or executing port structures in places where the creation of temporary artificial peninsulas with fill material is impracticable or not allowed. Hence the need to use floating work platforms, commonly referred to as barges."

Jan 1, 2017

By Johan F. W. Kock

"Hearing loss due to excessive noise exposure is the most prevalent industrial disease. It is ranked on the World Health Organization’s (WHO) priority list for major work related injuries. Uncontrolled noise not only has a physical effect, but is also a psychological hazard affecting the performance and well being of man. Noise induced hearing loss (NIHL) is irreversible, yet it is preventable. The first defence against noise (noise control engineering) is a high priority in the mining industry. Second defences should be a last resort when the engineering control of noise is inadequate. Hearing conservation programs and the use of conventional hearing protection devices seem to have failed in the prevention of noise induced hearing loss. If compensation payouts that quadrupled in the past ten years are used as a barometer for the success of existing hearing conservation programs, then new strategies and technologies need to be investigated. The best practice Hearing Protection Device (HPD) may be seen as the minimum standard for second defence noise control.Conventional hearing protection is widely applied, but also misused in the industry as well as in the mining sector. Empirical research results, ownership, general attitudes of workers as well as qualitative aspects will be explored. The paper provides reasons, evidence, case studies and strategies regarding the best practice hearing protection philosophy (the Noise Clipper Model) as implemented in the Implats Mining Group. Worldwide tendencies towards custom-made HPD’s, findings that indicate improvements in hearing conservation programs and finally the successful application of Custom-made Hearing Protection Devices, will be outlined."

Jan 1, 2003

By M. Grodner

Underground excavations exhibit different hangingwall conditions in response to varying geotechnical and mining situations. These differences need to be quantified so as to accurately determine the effectiveness of the mining and/or support strategies. A useful tool for the quantification of these differences is hangingwall profiling. Two methods of hangingwall profile measurement are described?termed irregular and periodic methods. Several data analysis techniques are reviewed for these methods and the suitable ones are discussed in detail. For irregular data the suitable techniques are the determination of the length, the average of the profile and the average absolute deviation from the mean of the profile. All of these techniques as well as determination of the moving average of the height and examination of the spectral image of the profile can be successfully applied to regular data. The effect of preconditioning on the hangingwall is discussed as an example and it is quantitatively shown that it results in improvements of conditions. The techniques described allow the engineer to quantitatively identify the appropriate support type or mining strategy and thus represent a valuable decision-making tool. It is suggested that these techniques should be employed on a routine basis by the rock engineers on the mines as part of their geotechnical classification, as well as support manufacturers to quantify the effectiveness of various support types.

Jan 1, 2000

By S. Dixon

The Peñasquito deposit in Mexico is one of the largest grassroots precious metal discoveries developed in recent years. Goldcorp Inc. acquired the gold-silver-lead-zinc property with the acquisition of Glamis in 2006. The Peñasquito property is located in the northeast corner of Zacatecas state, Mexico. The elevation of the property averages 1,900 m (6,200 ft) above sea level. It is situated in a wide east-west valley. Minera Peñasquito, S.A. de C.V., wholly owned subsidiary of Goldcorp Inc. has operated twin SABC-flotation lines since June 2010. Each line is capable of processing 50,000 tonne per day using a SABC grinding circuit followed by flotation to produce lead and zinc concentrates. The addition of a Polysius Polycom HPGR 2417 with dual 3,000 kW drives to reduce the crushed pebbles produced by the SAG mills was planned to increase production to 65,000 tonne per day per line. The production has been limited to 100,000 tpd due to operating issues in the grinding circuit. The operating issue has been the amount of pebbles generated by the SAG mills is significantly less than originally planned. This paper describes the planned installation of a crushed augmented feed to maximize utilization of the HPGR capacity. This coupled with full utilization of the SAG and Ball Mill available energies there is the potential to achieve a 50% total capacity increase from the grinding circuit.

Jan 1, 2012

By R. G. O'MEARA, Alexander M. Gow, W. T. SCHRENK

Lime is used extensively in the various industries. The National Lime Association in an excellent and recent bulletin lists 23 important in- dustries in which lime plays a vital role; and it thereby justifies the statement that "Lime is one of the most versatile and widely used reagents in the chemical and industrial world." There is, however, one application of this "universal" reagent which has not been mentioned. It is the use of lime in the flotation of ores. An appreciable percentage of the lime produc- tion is consumed by ore-dressing plants. The uses of lime throughout all the industries are more or less re- lated, but "lime" is a broad term; the varieties of lime are more mumerous than the limestones from which it is made, and its use involves a complicated technique. The interrelated application and growing importance of lime in flotation warrant this additional publication on the various "limes," with emphasis on those uses related to the function of lime in flotation. ཁྐྲ་ Lime in water treatment, cyaniding, and amalgamating will be men- tioned, after which its use in flotation will be taken up. This compendium was prepared by the Mississippi Valley Experiment Station of the United States Bureau of Mines and the Missouri School of Mines and Metallurgy, Rolla, Mo.

Apr 1, 1931

By B. M. Loftus

An investigation into the use of impinging stream (jet) reactors for the leaching of a free milling ore produced an increase in gold recovery by 10% while decreasing leaching time by up to 90%.Tests on refractory ores demonstrate no apparent improvement in recovery. However, leaching kinetics are dramatically increased when these ores are subjected to jet reaction prior to agitation.

Jan 1, 1997

The ability to track miners and communicate with them while they work in underground coal mines is important during normal daily operation, and critical in emergency conditions. This was evident during recent incidents at underground coal mines worldwide. Communication with miners and the knowledge of their location is of great importance for rescue efforts and the preservation of life. Numerous technologies have been developed, adapted and deployed to meet tracking requirements of the Mine Improvement and New Emergency Response (MINER) Act of 2006. Evaluating the performance of these systems has proven to be dif?cult for mine operators, system manufacturers and regulatory agencies. The MINER Act requires operators to improve accident preparedness by developing an emergency response plan speci?c to each mine. With the recent implementation of the provisions of the MINER Act of 2006, all underground coal mines in the United States are subject to the mandates of legislation concerning communication and tracking system installation. As of June 2011, 203 new or revised tracking and/or communication systems had been approved by the U.S. Mine Safety and Health Administration (MSHA), with nearly 50 other systems or revisions in the approval process (MSHA, 2011). At that time, the available approved systems for underground coal mine use included these types: ? Leaky feeder communication systems. ? Fixed node-based communications and/or tracking systems. ? Wireless node-based communications and/or tracking systems. ? Medium frequency (MF) communication systems. ? Communication system peripherals. Other types of tracking systems have since been developed and some manufacturers are seeking approval for use in this application. Some of the new products include through-the-earth (TTE) systems and various radio frequency (RF) adaptations. New technologies that are currently being developed and deployed in other industrial applications should also be considered, including acoustical, optical, inertial and hybrid technologies. To date, no uniform method has been employed in the industry to effectively compare and evaluate the performance of installed systems. Neither industry operators nor regulatory agencies can accurately assess the capabilities of installed systems in the continuously changing mine environment. There is a need for a uniform evaluation method that provides the ability to assess how different systems and technologies perform in various mining applications, and whether they can satisfy the regulatory requirements.

By J. M. Casas

This work presents the development of an ionic equilibrium model and its use to simulate the distribution and concentration of chemical species (speciation) in sulfuric acid - cupric sulfate solutions in the 0-2 pH range, 0.1-10 gpl copper concentration range and 15-45°C temperature range. The model consists of a set of equations which represent the equilibrium relationships for the ionic reactions and the mass balances for the components present in the system. The effect of ionic strength was taken into account by correcting the equilibrium constant in concentrated solutions. Several species can be formed at different pH and temperature values, the principal being: HSO-4, SO42-, CuSO4(aq), Cu2+, and H+ in order of increasing solution acidity. Simulations show that concentrations are highly dependent on pH. The sulfuric acid speciates mainly as bisulfate ion (HS0-4) and hydrogen ion (H+) at pH values lower than 1. The model presented in this work can be applied to predict and analyze the solution composition in electrolytic copper processes such as electrowinning, electrorefining and electrodialysis, as well as the purification of various industrial solutions.

Jan 1, 1999

By Kieran Black

The immediate roof lithology at United Colliery is extremely variable and provides a challenge for the design of secondary support. Support design in recent longwall installation roads at the mine has been carried out using strata management techniques. These techniques allow a robust yet economical secondary roof support design to be achieved. Analysis of roof lithology and roof displacement during first pass driveage are used as a basis for the optimisation of the secondary support design prior to roadway widening. This paper will demonstrate the application of practical strata management techniques in the optimisation of secondary roof support in six installation roadways at United Colliery. The experience gained from the installation roadways for LWs 1 to 5 will be briefy discussed. The experience from LW 6 will be discussed in greater detail. The paper will describe the strata management system that was used, including mapping, borescoping and extensometry, as well as the development and application of a Trigger Action Response Plan (TARP).

Jan 1, 2007

By Oliver Bowles

Whiting or Paris white is a fine-grained preparation of calcium carbonate having a wide variety of uses. Until recent years it was prepared almost exclusively from certain north European chalks. With the curtailment of imports of European chalk during the World War of 1914-18, however, finely ground limestone, of domestic origin was used more extensively to satisfy the American demand.

Jan 1, 1942

By A. C. T. Bigg

"The mineral potential of the Nanisivik area was discovered as far back as 1910 when a prospector of the Geological Survey of Canada, on an expedition under Captain J. G.Bernier, recorded a deposit of pyrite with minor sphalerite and galena. An outcrop of the present orebody was discovered by Texas Gulf Company in 1957. Subsequent drilling outlined the orebody consisting of 6,000,000 tonnes of ore containing 13 % Zinc and 1.5 % Lead. The orebody appears to have been formed by the filling of a limestone cavern with sulphides. The sulphide minerals consist of pyrite, sphalerite and galena. The limestone bedrock is mostly dolomite with some calcite and magnesite. A cutoff grade of about 6% Zinc has been calculated.In 1972 Mineral Resources International Limited took an option on the property. Upon completion of the feasibility study by Watts, Griffiths and McOuat, the then new independent project management group of Strathcona Mineral Services Ltd. were engaged to develop the project through the financing, construction and operating phases. Strathcona Mineral Services still manage the project from their head office in Toronto and through the Mine Manager and Department Superintendents at the Mine site. The interest for the project is presently split five ways: Mineral Resources International Ltd. 53.5 %, Government of Canada 18 %, Metallgesellschaft A.G. of Germany 11.25 %, Billiton B. V. of Holland 11.25 % and Texas Gulf Co. 6 %."

Jan 1, 1980

By D. R. Rathburn

Jan 1, 1962

By H. Fayed

Two-phase (water and air) flow in a self aerated WEMCO flotation machine has been investigated using computational fluid dynamics (CFD). A 0.8 m3 model is considered. The flow is modeled by Euler-Euler approach, and transport equations are solved using a commercial software ANSYS-CFX5 [1]. Because of the lack of circumferential periodicity in this machine, the entire machine is modeled and unsteady simulations are conducted in the whole volume of the bulb. Uniform bubble diameter is specified, and the effects of bubble diameter are determined by conducting simulations for three diameters of 0.5, 0.7, and 1.0 mm. The unsteady air flow rate through the machine is predicted as an outcome of the simulations. Air volume fraction contours and velocity field in different parts of the machine are presented and discussed.

Jan 1, 2012