Search Documents

By James F. Kvitkovich, George V. Weisdack

Longwall mining techniques were introduced into U.S. bituminous coal mining operations in the early 1960s. These techniques were gradually adopted by many mines during the 1970s. By 1983, considered to be the peak of the longwall mine census, there were 118 active longwall faces in 79 coal mines throughout the United States. Beginning in 1984, longwall faces began a decline in numbers that has continued to the present day (Fig. 1). The geographic distribution of longwall faces today is shown in Fig.2 according to region. A breakdown of recent longwall mine production by region is shown in Table 1. An approximate breakdown of present longwall face installations by product (metallurgical and steam) is shown in Table 2.

Jan 1, 2005

By D. Tao, R. Honakey, B. K. Parekh

The dewatering of stable phosphatic clay suspensions generated from phosphate beneficiation in the central Florida is an issue of practical and theoretical importance. Because of its tiny particle size and surface charge, the phosphatic clay takes up to 20-30 years to settle in water and causes environmental, aesthetic, economic, and handling problems. An efficient and cost-effective dewatering/consolidation process for phosphatic clay is of great interest to the phosphate industry in Florida. In this paper, the consolidation and dewatering behavior of phosphatic clay was studied by use of anionic flocculants with and without sand addition. The effects of pH, initial polymer concentration, polymer dosage, polymer addition steps, and metal cations (K+, Ca2+, and Al3+) on the flocculation of phosphatic clay have been studied. Experimental results indicated that clay suspensions were well flocculated at pH 10.5 by DPW-1-1355 and Magnafloc 5250 flocculants acquired from Ciba Specialty Chemicals. Sand particles from phosphate flotation added to the clay slurry promoted flocculation and increased clay consolidation. K+ showed good performance to improve the flocculation characteristics by neutralizing clay surface charge. The adsorption mechanisms of flocculants on clay particles were also discussed in this paper.

Jan 1, 2006

By James M. Harrington, A. Azra Bilgin, JoAnn Silverstein

The prevention of AMD in situ is more attractive compared to subsequent downgradient treatment alternatives that do not involve source control. AMD source control can be achieved by shifting the microbial activity in the sulfidic rock from pyrite oxidation to anaerobic heterotrophic activity. This is achieved by adding biodegradable organic carbon amendments to the sulfidic rock. This technique was applied in an abandoned mine pool with a pH of 3-3.5. Following treatment, near-neutral pH and decreased effluent heavy metal concentrations were achieved. In situ bioremediation by enhancement of bacterial iron and sulfate reduction is a promising technology for AMD prevention.

Jan 1, 2005

By Stefan Basista, Janusz Tomala

Modern constructions of electric ferroalloy furnaces are still based on applying in the lower "liquid" areas the standard carbon materials. What can be illustrated by the experience from several years, in the part of tap hole, hearth walls and bottom, is that so-called carbon or semigraphite microporous materials are successfully being applied. These materials, compared to the standard carbon, give better resistance to the attack by liquid metal and other wear factors. Generally this group includes materials characterised by considerable share of pores of diameters below1µm (significantly exceeding 90% of total porosity). The microporosity increases the resistance to the infiltration of the liquid metal. The effect of microporosity can be obtained by introducing silicon (or its compound) additive to materials based on electrically (or gas) calcined anthracites, electrographite and binder. Moreover, by introducing other ceramic additives, the microporous materials are more resistant to dissolution by the liquid metal. Observing the trends of "improving the materials" in the last years, it is clearly seen that the share of non-carbon additives is bigger and bigger, so we can reasonably speak of rather carbon-ceramic materials. In this paper, the survey of the most important quality criteria, which must be met by the carbon furnace linings, as well as the new testing methods will be presented.

Jan 1, 2007

By G. T. Lapidus, R. Zárate-Gutiérrez

Selective leaching of lead from a Pb-Ag-Zn concentrate with hydrogen peroxide in citrate solutions was studied at room temperature. Leaching tests were performed, varying the H2O2 concentration and the solid-liquid ratio, holding the solution pH constant at 7, and the citrate concentration at 1 M. Lead extractions of 100 % were achieved with 4 and 5 times the stoichiometric quantity needed to form elemental sulfur, with only a small amount of metal impurities dissolved (Ag, Zn and Fe). The lead solubility limit at those conditions was found to be ~21 g L-1. X-ray diffraction analyses of the leach residues were free of galena (PbS), while other metal sulfides, such as sphalerite (ZnS), chalcopyrite (CuFeS2) and pyrite (FeS2), were basically unaffected.

Jan 1, 2014

By N. S. Dalal, X. Shi

While it is known that vanadate and related compounds of pentavalent vanadium ( V (V)) exert potent toxic effects on a wide variety of biological systems, the underlying biochemical mechanism is still not fully understood ( 1- 3). One of the pathways is thought to involve the oxidation of NAD ( P) H. Thus, considerable effort has been devoted to finding the mechanism of NAD ( P) H oxidation by Vcvi (1-15). Erdmann et al. (5) first noted that vanadate stimulated the oxidation of NADH by plasma membranes and attributed this effect to a membrane containing NAD(P)H-dependent V(V) reductase. Later studies by Liochev and Fridovich indicated that endogenous superoxide ( 02 ) plays a central role in this reaction ( 4, 12, 13) . They proposed that NAD ( P) H dehydrogenases or oxidases produce 02, which causes VCV ) to stimulate NAD ( P) H oxidation via the following free radical chain mechanism ( 4, 12, 13) :

Mar 1, 1992

Canadian mining giant Teck Resources Ltd. will be the exclusive supplier of the metals used in the production of the more than 1,000 medals to be awarded at the Vancouver 2010 Olympic and Paralympic Winter Games. Teck, the diversified resource company headquartered in Vancouver, B.C., is providing 2.05 kg (4.5 lbs) of gold, 1,950 kg (4,300 lbs) of silver and 903 kg (2,000 lbs) of copper sourced from its operations around the world. In addition to the raw materials mines, this year?s medals will make Olympic history as they will be the first to contain metals recovered from processing the circuit boards from end-of-life electronics (e-waste) that would have otherwise been destined for a landfill. After mining or production through a variety of smelting and recovery processes, each metal has been refined to enhance the metal purity.

Jan 1, 2010

By L. R. Nelson

A review is presented of the furnace cooling system design and operating developments since the initial furnace start-up in January 2001 of the Chambishi DC-arc furnace to produce ferrocobalt alloy. The furnace operating conditions present a number of challenges to the furnace designers and operators, in particular, to provide a sustainable lining that can withstand the highly corrosive siliceous slag (roughly 50% SiO2). This is exacerbated by the dual requirement of operating this slag in a relatively highly superheated state (?T ?400°C when tapped at 1550°C) to ensure that the ferroalloy can be tapped (estimated 1370°C alloy liquidus temperature) prior to atomization. The core design challenge occurs at the alloy-slag interface, where a single refractory type cannot simultaneously meet the dual requirement of both adequate alloy and slag corrosion compatibility. Progression by the fourth furnace campaign to involve a retrofit of the bath sidewall to HATCH high-intensity, water-cooled, copper Waffle coolers and tap blocks is described. This involves operation of the entire slag bath, the slag-alloy interface and a portion of the alloy within a more chemically compatible refractory/slag (and possibly at times even an alloy) freeze-lining. Due to the high furnace power density employed (up to 500 kW/m2 hearth area), coupled with the large slag superheat needed, the resulting imposed peak bath sidewall heat fluxes are substantial, especially in the alloy (typically averaging 170 kW/m2), and on occasion have exceeded 1000 kW/m2. The performance of the HATCH Copper Waffle coolers under such aggressive process pyrometallurgical conditions is described. Aspects of the design and especially operating strategies to effect sustained production at up to 38 MW power input are also discussed.

Jan 1, 2004

This appendix contains the list of equipment selected for the capitol cost estimate, with the respective quotations from their vendors/manufacturers. A vendor response report along with a separate equipment and motor list has been included in the first part of this appendix.

Jan 1, 1979

The New Technology of Enrichment of a Fine Low-Grade Tungsten from Complex Multi-Metallic Ore

Sep 13, 2010

By D. Mohapatra

The possibility of using 2,2,4-trimethyl-1,3-pentanediol dissolved in tetrachloromethane as extractant for boron recovery is discussed. The parameters optimized for this purpose are contact time, boron concentration in the aqueous phase, extractant concentration, equilibrium pH and phase ratio. NaOH is used as stripping agent for boron recovery from the loaded organic phase. Boron extraction is found to be a slow process (equilibrium time 20 minutes) compared to boron stripping, which is reasonably fast (equilibrium time 5 min). Maximum boron extraction is possible at a broad pH range from 1.0 to 6.0. Using 1.0M extractant concentration, a 1:1 phase ratio (organic: aqueous) and two stages, ~99% boron extraction is achieved. More than 97% boron stripping is possible using 0.5M NaOH at a 1:1 (organic: aqueous) phase ratio in two stages. Overall, a 95.6% boron recovery was achieved. Loss of solvent into the aqueous phase and co-extraction of Ca, Na and K into the organic phase at higher equilibrium pH are two major concerns in his process.

Jan 1, 2008

By B. Waterman, D. Ramey, L. Schlink

"Water is a primary commodity for most industrial processes. It has become a global focus in light of climate change and population growth. Reuse of process water has two major benefits - minimize the amount of fresh water added now and minimize the amount of discharge water that requires treatment later.Mining and mine product processing has its share of reused water. For example, reclaim water from a tailings impoundment, overflow from thickeners and leach solution to raffinate and back again all demonstrate the use and reuse of water in mining circuits. Eventually, a mine reduces production or ceases operations completely, eliminating the option to reuse the impacted water and, thus, requires treatment of the remaining water.Current methods of water treatment remove the impacts, providing clean water for discharge, but leaves behind a concentrated waste that requires further treatment or disposal of a hazardous waste. Freeport- McMoRan is currently testing three water treatment technologies specific for sulfate and/or metal removal from mine impacted water with the approach of transformation not concentration. These technologies provide clean water for alternative use while creating byproducts that could be marketable, or disposed as a nonhazardous material, thereby reducing the cost and longterm liability of disposal.The selection of a water treatment process is site-specific. The volume of water, contaminant to be removed, disposal options, length of time for treatment, location of plant and reagents and discharge requirements are some of the factors that need to be considered when selecting a water treatment process. Common water treatment technologies for mine impacted water consist of low- or high-density sludge (LDS/ HDS), reverse osmosis (RO) and evaporative technologies. In addition to operating costs, these processes require additional handling of the concentrated sludge or brine. Advanced water treatment technologies include ion exchange, solvent extraction and metals precipitation with or without the aid of a biological system. Some of the more complex systems have a series of unit operations to achieve required discharge regulations."

Jan 1, 2014

By Valérie Léveillé

As new legislation drives to lower SO2 emissions from metallurgical plants, plant managers face the challenge of keeping their costs under control. The Cansolv® SO2 Scrubbing System has been broadly adopted in the non-ferrous industry as a cost effective solution for smelter operators to meet the new SO2 emissions targets. The Cansolv® SO2 Scrubbing System is an amine-based regenerable process that selectively absorbs SO2 from a variety of gases, including dilute smelter gases, such as furnace and converter gases. The system produces a pure, water-saturated SO2 byproduct stream, which can then be directed to the front end of a sulfuric acid plant for conversion to sulfuric acid. When deployed in a smelter complex, the Cansolv® SO2 Scrubbing System may also be used to process acid plant tail gas, allowing single absorption sulfuric acid plants to achieve emissions an order of magnitude lower than that of a double absorption acid plant with a lower capital investment. Depending on inlet gas temperature SO2 emissions in the treated gas can be controlled to as low as 55 mg/Nm3. This paper will describe some of the applications where customers have or are planning to use the Cansolv® SO2 Scrubbing System and what as well as which features and cost advantages for the treatment of smelter gases were key to the technology choice.

Jan 1, 2009

By H. C. Fuller, J. H. Jacobs

"Manganese ore from Metals Reserve stock piles at Deming, N. Mex., Cushman, Ark., and Philipsburg, Mont., were processed in the Bureau of Mines pilot plant at Boulder City, Nev., to determine their suitability for the production of electrolytic manganese. Manganese was produced successfully from all of the ores.The ores, crushed and ground to minus 33-mesh, were roasted in a Skinner furnace to reduce the manganese and were then leached with spent electrolyte, from the cells, containing sulfuric acid. Acid-leach extractions of 96 percent on Deming, 89 percent on Cushman, and 97.5 percent on Philipsburg ores were obtained. Neutralization of leaches with ammonia results in the highest manganese extraction; but Cushman and Deming leaches could not be neutralized with ammonia, because the amount required was more than enough to maintain the proper ammonium sulfate concentration. A combination of ammonia and calcine was used. However, ammonia was satisfactory for neutralization of Philipsburg leaches. Sulfuric acid needed for make-up was as follows: Deming, 0.380 pound per pound of manganese extracted when neutralized with ammonia and calcine; Cashman, 0.402 pound per pound of manganese extracted when neutralized with ammonia and calcine; Philipsburg, 0.594 round per pound of manganese extracted when neutralized with ammonia alone.All of the leach slurries settled well enough to be separated and washed in countercurrent thickeners.Impurities were precipitated with hydrogen sulfide and removed by filtration. Cushman ore solution contained only- small amounts of impurities and required 0.055 gram of hydrogen sulfide per liter of solution for purification. Deming and Philipsburg solutions contained large amounts of zinc and required 0.55 and 0.65 gram of hydrogen sulfide per liter of solution, respectively.Electrodeposition was satisfactory on all three ores and current efficiencies of 62 to 66 were obtained.A process for the production of electrolytic manganese has been developed by the Bureau of Mines, first on a laboratory scale4/ and then on a semicommercial pilot-plant scale.5/ At first the- pilot plant operated on ore from the Three Kids mine near Las Vegas, Nev., to determine the practical features of the process on ore of this type. Since completing the work on this ore, the pilot plant has been used for processing other domestic ores to obtain engineering data and other economic information regarding the amenability of such ores to the process."

Sep 1, 1946

By Franziska Günther, Helmut Mischo

The calculation of costs for an underground mine, as well as the planning of the equipment and materials to be used, is a complex and time-consuming process. The estimation depends on a multitude of parameters, and all mining processes are interconnected. A novel tool has been developed that enables automated calculation of underground mines and allows for the comparison of the effects of changing individual parameters. Previously, changing individual planning parameters often necessitated a complete recalculation of the mine. The newly developed calculation tool provides an innovative planning aid that allows for more efficient and accurate mine planning and cost estimation. The tool enables the user to implement continuously up-to-data costs and prices. This allows for more accurate planning data and results. The underlying concept of the calculation tool, its implementation at a planned quartz porphyry mine in Germany, and the verification of the tool at an existing underground mine will be presented.

Feb 1, 2025

By Frank E. Federspiel

In 1992, the Bureau of Mines conducted a mineral resource investigation of the 78,000-acre Garns Mountain study area in southeastern Idaho. The area had been proposed for Wilderness. It is underlain by Paleozoic to Mesozoic-age sedimentary rocks about 11,000 feet thick. Rocks have been faulted, offset, and folded as part of the northerly-trending Idaho-Wyoming Overthrust Belt. Study area mineral occurrences are: phosphate in the Permian Phosphoria Formation; coal in the Cretaceous Frontier end Bear River Formations; and uranium in carbonaceous and phosphate-bearing shales and coal of these formations. Four zones of phosphate are estimated to contain about 528 mitt ion tons of rock with over 10% P205; samples of phosphate-rich rock also contained as much as 3950 ppm chromium, 3280 ppm vanadium, 23 ppm gallium, and 5540 ppm zinc. Fragments of poor-quality coal and carbonaceous shale were found in the area; coal was mined near the northeast border. Uranium content up to 0.016% U3O8 is in carbon-rich shales. Oil and gas were drilled for, with minimal success, in folded sedimentary rocks (frontier and Nugget Sandstone) in the Horseshoe anticline, near the east border. Examined workings included 12 dozer cuts, 4 trenches, 2 prospect pits, and 2 caved adits. No production is known, and no leases or claims are held for the area.

Jan 1, 1992

By Karla Carolina Alves da Silvar

As ligas com memória de forma (LMFs) destacam-se por apresentar propriedades especiais, possibilitando seu emprego em diversas aplicações tecnológicas. Esses materiais podem ser integrados a uma matriz polimérica, agindo como um reforço, constituindo uma nova classe de matérias, chamada de Compósitos Inteligentes, que têm despertado interesse por sua versatilidade na criação de atuadores e/ou sensores. Nesse contexto, fios de nitinol, foram tratados termicamente para obter temperaturas de transformação próximas a ambiente. Em seguida, amostras desse material foram submetidas a calorimetria diferencial de varredura para verificação das temperaturas de transformação. Posteriormente, os fios tratados receberam um treinamento termomecânico para obtenção do efeito memória de forma reversível e assim executar o movimento similar a abertura e ao fechamento de uma garra, pretendido para o atuador a ser desenvolvido. Após essa etapa, os fios já treinados foram incorporados a matriz constituída por silicone e resina epóxi, dando origem a um compósito que ao ser ativado por uma corrente elétrica, reproduz o movimento do treinamento termomecânico dado aos fios. Esta pesquisa tem por finalidade, desenvolver um atuador constituído por um compósito inteligente, analisando características como: transformação martensítica e flexibilidade.

Aug 8, 2018

By R. H. Grau, S. B. Robertson, F. Garcia, A. C. Smith, T. P. Mucho

Researchers working for the National Institute for Occupational Safety and Health (NIOSH) at the Pittsburgh Research Laboratory are developing ways to protect the health of miners. Part of that effort is devoted to improving the air quality in underground stone mines by developing ventilation techniques that can be used in these types of operations. The air quality in these large opening nonmetal mines can be significantly improved by using diesel particulate matter (DPM) controls along with sufficient ventilation quantities to remove contaminants. Practical methods of ventilating these underground stone mines can be accomplished by using mine layouts that course and separate ventilation air through the use of stoppings. The design, construction, and maintenance of effective stoppings in large openings have been a real challenge to mine operators. Several different types of stoppings have and can be used for this application. The choice of stopping design, material used, and construction techniques should be dependent upon a number of factors such as the intended life and effectiveness desired.

By Michel Rodrigue, Sylvain Duchesne, Louis Racine

"LocationThe Louvicourt mine is located 20 km east of Val d'Or in Abitibi, in the northwest part of the province of Quebec. The mine is located on Highway 117 connecting Val d'Or to Montreal and very close to the main railway networkHistoryFive successive exploration attempts by Aur Resources resulted in the discovery of the large Louvicourt orebody in June 1989. Construction of the surface and underground infrastructures commenced in the spring of 1991. Milling operations commenced in July 1994. The entire project cost CDN$290 million, almost CDN$20 million less than initially estimated. The concentrator infrastructure cost CDN$64 million.Louvicourt mine is owned in partnership by Novicourt Inc. (45%), Teck Corporation (25%), and Aur Resources Inc., the administrator (30%).Brief DescriptionLouvicourt mine is the largest producer of base metals (Cu and Zn) in Abitibi-Temiscamingue. Its average daily production is nearly 4300 t of ore, for an annual production of 200 000 t of copper concentrate (28% Cu) and 33 000 t of zinc concentrate (57% Zn). After only a few weeks of operation, it had attained its objectives for the most part, and operations continue to be improved."

Jan 1, 2000

By E. Fried

Cemented paste backfill (CPB) is an innovative tailings management method that consists in returning considerable amounts of mine tailings into the underground mine openings. The filled stopes thus participate to the ground support that allows maximizing orebody extraction and a safer environment for the mine workers. There are also significant environmental advantages of using CPB. Indeed, up to 50% of the concentrator tailings can be backfilled, leading to a smaller volume of problematic waste materials to be managed at the surface. Once the CPB is placed, or when the mine is flooded at its end-life, the backfill is subjected to underground water flows that may leach and spread the pollutants (mainly metals, sulphates, and acidity) which can contaminate the underground waters. The aim of this study is to characterize the leaching properties of CPB material and to identify the cement phases that ensure the metal fixation. A laboratory procedure was implemented consisting in the preparation of various paste backfill mixtures using sulphide-rich and sulphide-free materials, different types of binder, and mixing waters having various sulphates, copper and zinc concentrations. After 90-days curing time, the samples were submitted to column leaching tests. The CPB materials were flushed each day with 100 ml of deionised water during 100 days. The collected leachates were then analyzed for pH, Eh, electric conductivity and chemical composition. For some samples, a differential acid neutralisation test was carried out. The objective of this experiment is to dissolve selectively the hydrated phases by adding incremental acid concentrations. By analyzing punctually the equilibrated solutions, the composition of the dissolved phases and their metal content can be estimated. The leaching test results showed that the pH of the leachates remains alkaline during the test period. When the pH decreases under 10 (after 30 days), different behaviours in terms of chemical element release (especially for zinc) were observed. During the test, the oxidation of pyrite seems to slow down, probably due to passivating phenomena. Moreover, the differential acid neutralisation test results allowed a better understanding of the CPB mineralogy and the Zn-bearing cement phases. Zinc and the other metals seem to be fixed within a calcium-magnesium silicate.

May 1, 2007