Search Documents

By P. J. Sylvester, D. H. C. Wilton, R. I. Wheeler, M. A. E. Huminick, D. Evans-Lamswood

"Abstract — Systematic characterization of the mineralogy of massive sulfide ore deposits can provide valuable insights into ore genesis and metallurgical processing that would not be apparent otherwise. We describe a method wherein (1) normative mineral abundances are calculated from whole-rock chemical assays using an algorithm, (2) the results are cast in block models, (3) the results are then verified with automated image analysis of a subset of samples prepared as grain mounts by backscattered electron imaging and X-ray mapping on a scanning electron microscope, and (4) those verified results are integrated with textural data determined by optical microscopy.The technique is applied to the magmatic Ni-Cu-Co sulfides of the Ovoid orebody, based on geochemical assays of 3175 whole-rock samples. Three principal ore zones are defined in the Ovoid. Type I ore occurs in the center of the deposit; it is magnetite-rich and pyrrhotite-poor with intermediate contents of pentlandite and chalcopyrite. Type II ore surrounds Type I ore and is pentlanditechalcopyrite- rich with intermediate contents of pyrrhotite and magnetite. Type III ore occurs at the base and along the outer periphery of the northern part of the orebody; it is pyrrhotite-rich and chalcopyrite- poor with an intermediate content of pentlandite, and a low-to-intermediate content of magnetite."

Jan 1, 2012

By L. A. Cranson

WHEN I came out of Stanford University in 1922, the out-look for men trained in geology, petroleum engineering, and mining was indeed dismal; in fact, so much so that most of us looked upon our future in those fields as pretty hopeless. Neither our professors nor those men in industry with whom we came in contact gave us any enthusiastic encouragement as to the future of ourselves or the fields we had chosen for our labors. I believe that the attitude of pessimism which saturates everyone about graduation time is lament able and short-sighted, and may often start a young man on his way with an attitude of defeatism. Instead, he should be starting out knowing that he can expect hard work and keen competition, but that the fields of his labours are expanding at an accelerated rate, and that strong, energetic efforts will as always accomplish highly satisfactory results.

Jan 1, 1941

By E. M. Frizzell

It is unlikely that improvement in truck efficiency and capacity can fully offset the effects of inflation, fuel cost/shortages, and increasing haul distances as in the past. Therefore, investigations of haulage systems less sensitive to these problems are warranted. Thus, this Bureau of Mines contract research study on alternative continuous haulage systems was prepared. This study identifies the physical, economic, and technological parameters in the application of continuous haulage systems with special attention to under pit slope conveyors and skip hoisting systems. The evaluation data were gathered from extensive literature searches, European/North American mine visits, and industry comments. The study concludes that continuous underground haulage is a viable method within the proper geometric configurations.

Jan 1, 1979

By Rameshwar Sah, Bharath Kumar Shanmugam, Govinda Raj Mandela, Marutiram Kaza, Harsha Vardhan, Harish Hanumanthappa

Iron ores obtained from different sources differ in their chemical and physical properties. These variations make the process of grinding a difficult task. The work carried out in this context focuses on three different samples of iron ore, viz., high silica high alumina, low silica high alumina, and low silica low alumina. The grinding process for all the three iron ores is carried out individually in Bond’s ball mill and the total retention time taken by each iron ore sample is calculated. The present investigation focuses on utilizing the calculated retention time of the iron ore as a standard grinding reference time to the laboratory ball mill for optimizing the grinding time of each ore. The desired P80 (150 μm) with an acceptable range of hematite liberation (> 75%) was obtained in the laboratory ball mill after reducing 6 min from the total retention time taken in the Bond ball mill.

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and the results are described in this report.

Jan 1, 1983

The U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) are participating jointly in a research program to evaluate the strength characteristics and air-leakage resistance of various proposed seal designs for use in underground coal mines. The full-scale seals were constructed in the USBM's experimental mine at the Lake Lynn Laboratory, air-leakage tested, then subjected to pressure pulses of 20 psig or greater. In experiments prior to this study, seven seal designs using solid-concrete blocks were tested. Only the standard-type seal passed the explosion and air-leakage criteria. Tests also were performed on four seals constructed with low-density foam blocks. All four of these seal designs withstood the pressure pulse. In more recent studies, nine cementitious foam seal designs of varying thicknesses and densities were investigated. Six of the nine designs successfully survived the explosion overpressures. Six wood-block convergence seals also have been tested. The typical 3-ft-thick, wood-block seal design currently used in many coal mines did not maintain its integrity, in the absence of convergence forces, following the explosion test. Five modified wood-block seals successfully withstood the 20-psig pressure pulse. Based on these tests, three alternative seal construction materials, cementitious foam, low-density foam block, and wood, have been approved by MSHA for use in underground coal mines.

Jan 1, 2010

By Jeffrey D. Winterton

Keywords: Copper, ion exchange, sulfonic acid, bis-picolylamine, ion exchange modeling, ion exchange kinetics As part of an investigation into the feasibility of using ion exchange resins to recover copper from aqueous waste streams generated during the manufacturing of semiconductor devices, the uptake of copper onto two ion exchange resins was investigated. The resins studied were DOWEX G-26, a standard gel type sulfonic acid resin, and DOWEX M4195, a macroporous chelating resin with a bis-picolylamine functional group. The equilibrium and kinetic behavior of the uptake of copper were investigated over a range of copper concentrations with constant sulfate concentration and different levels of acidity. The homogeneous structure of the G-26 resin yields equilibrium relationships that fit the Langmuir equation, and equilibration times of less than 30 minutes. The uptake behavior of M4195 is complicated by the need to absorb co-ions to maintain electroneutrality, resulting in uptake profiles that change character with increasing copper concentrations, and extended equilibration times.

Jan 1, 2005

By A. L. Sweetser

EXPERIENCE has shown how difficult it is to obtain information regarding laboratory-tests in connection with the chlorination-process for the extraction of gold from its ores, and I therefore present the following method, somewhat in detail, for the benefit of those who may desire to pursue research work in this field. The ore chosen was a partly-decomposed porphyry, extremely siliceous and comparatively soft, and of an average value per ton of from $25 to $26 in gold and $0.68 in silver. The chemical analysis gave : Fe2O3, 3.35; FeS, 1.5; MnO2, 0.75; ZnCO3, 4; Al2O3, 3.20; H2O, 0.7; SiO2 and insol., 83.50 per cent. The ore, first crushed to pass a 5-mesh screen, was coned and quartered until a 45-lb. sample was obtained. Samples for assay and analysis, taken from this lot by means of riffles, were crushed to pass a 100-mesh screen. The original sample was divided into 10-lb. lots, of which one was crushed to pass a 10-mesh screen; another through a 12-; the third through a 20-, .and the last through a 30-mesh screen. Because of the production of an excessive quantity of fine material it was deemed inexpedient to crush finer than 30-mesh size-a decision the wisdom of which is proved by the data in Table I., showing the increasing ratio of slimes, in proportion as the ore is crushed finer. In order to determine the percentage of fines in the sizes of mesh selected, a weighed sample of ore was taken from each mesh, and a sample from the 10-mesh lot was passed successively through 20-, 40- and 100-mesh screens, and the percentage remaining on each screen determined. This process was repeated with the 12-, 20- and 30-mesh lots, with the results given in Table I.

Sep 1, 1907

By Osvaldo Bascur, Barun Gorain, Jaco Steyn

"The last few decades have seen some remarkable advancement in information technology, but recently various digital technologies have resulted in several synergies to deliver innovation in diverse applications. The mining industry has been relatively slow in adopting these technologies compared to the other industries, but this scenario is changing fast.Challenges. Mining companies globally are going through a series of challenges such as declining ore grades with complex metallurgy, increasing depth of ore bodies, high capital and operating costs, lower productivity, shortage of technical resources, significant pressure from stake-holders to deliver, along with growing environmental and corporate social responsibility issues. Improvement in profitability would need significant improvements in operational performance.Consequently, over the last few years, there has been a major focus among some mining companies to imbibe operational excellence. This has been only possible because of the replacement of a silos-based approach by an integrated view of the organization. Such an integrated view is now possible via the evolving digital technologies. Even so, such a transformation calls for a change in culture, which, for most organizations is not trivial. Attempts in the past to integrate functions, such as through mine-to-mill initiatives in the mining industry, have demonstrated significant benefits to many operations (McKee, 2013). Still, sustaining these benefits has clearly been a challenge due to manpower turnover and lack of proper systems and structures that integrate information between business functions within an operation and between operations and the corporate level.Opportunities. The advent of digital technology has opened up opportunities to integrate interdepartmental information for a unified understanding across an entire organization. The advances in instrumentation, equipment control systems, supervisory control systems (SCADA/ Historian) and industrial networks have helped in the direction of enterprise- wide integration. The availability of real time information across an enterprise has given rise to numerous possibilities to improve organization performance. As suggested by Seshan and Gorain (2016), some of the potential opportunities are as follows:"

Jan 9, 2018

By J. B. Carman

This paper, describing the concentrator of the Molybdenum Corporation of America in Taos County, northern New Mexico. 7 miles east of Questa, is one of a series on milling methods being prepared for and published by the United States Bureau of Mines. The mine from which the ore comes is 1 1/4 miles from the mill, and produces about 40 tons of ore per day by the cut-and-fill method.3 The ore contains about 5 per cent of MoS2. The mill has a capacity of 50 tons of ore per day and utilizes flotation methods. Water is taken from Red River. Power is generated by a water wheel, or by a Diesel engine in times of water shortage during the winter. The mill is located close to the bottom of a canyon, in order to obtain maximum head or, the water wheel, and the flow of ore is therefore maintained partly by gravity and partly by an elevator and pumps. ORE TREATED The MoS2 content of the concentrator feed ranges from 4.5 to 7.5 biotite, fluorite, small amounts of rhodochrosite and calcite, and the minerals of the granodiorite country rock.

Jan 1, 1932

By S Arai

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Podiform chromitites are commonly found in the Moho transition zone to the mantle section of ophiolites, but have been very rarely found from the current ocean floor, even though some ophiolites are considered as a slice of oceanic lithosphere. One of the factors controlling podiform chromitite formation is the chemistry of host mantle peridotite; an intermediately refractory harzburgite is the optimum host for chromitites. This harzburgite represents the most common lithology of the oceanic lithosphere, where the peridotite-melt reaction, which is another condition, is possibly common there. The oceanic lithosphere mantle is thus a good host for podiform chromitites. The apparent rarity of documented oceanic chromitites is solely due to under-sampling of mantle materials from the fast-spreading ridge and the segment centre of slow-spreading ridges. Some ophiolitic chromitites formed not from genuine mid-ocean-ridge basalt (MORB) but from wet MORB due to the situation of typical ophiolites, which formed not at ordinary mid-ocean ridges but at supra-subduction zone spreading centres.CITATION:Arai, S, 2015. Podiform chromitites do form beneath mid-ocean ridges , in Proceedings PACRIM 2015 Congress, pp 465–468 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By H. E. Frimmel

Abstract - Most of the gold in the Late Archean Witwatersrand Basin is of detrital origin but, in its present form, it is metamorphosed. The only relict detrital features preserved are the morpho­logical characteristics of some placer gold particles. Regional burial metamorphism in the shallower and deeper levels of the Witwatersrand Supergroup reached temperatures around 300°C and 350°C at pressures between 2 kbar and 3 kbar, respectively , estimated from phase relations, chlorite-chloritoid exchange thermometry and chlorite thermometry . Metamorphism of the gold involved compositional homogenization of individual gold particles and partial recrystallization. Various infiltration events caused the partial mobilization of the gold at slightly lower temperatures, between 240°C and 300°C. These infiltrations can be related to crustal extension during the deposition of massive carbonate sequences of the Transvaal Supergroup (around 2.5 Ga), and later to the emplacement of the Bushveld Complex, and to the Vredefort event around 2.0 Ga ago. The mobility of the gold was dependent on the sulfur fugacity prevailing in a particular horizon which, in turn, was deter­ mined by the amount of pyrite (and other sulfides) present in that horizon. With the sulfur fugacity being controlled by stratigraphy, low fluid:rock ratios in a pyrite-rich horizon were most conducive for the mobilization of the gold. Thus, long-range gold mobilization in the Witwatersrand Basin can be expected to be the exception rather than the rule.

Jan 1, 1994

By Takashi Furuyama, Sukeyuki Mori, Takafumi Okuma, Norio Hashiguchi

The Tower mill KD-3 is an improved version of the laboratory mills VD-1, KD-1 and KD-2 in which the classifying column has been modified to ensure a quick discharge of products from the comminution section and, on the other hand, a better separation of coarse and fine particles; the latter being collected in a cyclone with a central spiral ribbon. To level the circling airflow through the classifying column and have a strict control over the maximum size of collected particles, a series of experiments was carried out, modifying the internal structure of the column: insertion of a vertical plate, a cone, or a horizontal net. The relationship established between the maximum size of products collected in the cyclone and the duct airflow rate indicates that, independently of the latter, the insertion of a cone in the classifying column could stabilize the maximum size of products collected in the cyclone around 15.1 - 17.5µm. With a horizontal net, the maximal size could be reduced to 8.4 - 11.3µm. This occurrence might result from the collision of coarse particles blown from the comminution zone with the base of the inserted materials and their settling down the bottom of the classifying column.

Jan 1, 2003

By J. Lobel, M. Bourassa, J. A. Kozinski, B. Peng

Non-isothermal kinetics studies of the reduction phenomenon of electric arc furnace (EAF) dust generated in stainless steelmaking have been carried out. The dust was mixed with carbon as a reducing agent and dolomite as a binder to form pellets. A Thermo-Gravimetric Analyzer (TGA) was used to determine the weight loss of pellets heated at an average rate of 40 K/min. up to a temperature of 1500°C. The degree of metal reduction was calculated by considering the pellet weight loss, and evaporation of moisture, dust, zinc and lead at high temperature. The reduction process was divided into three different steps. The first covers the 300°C to 760°C temperature range (from 7 to 18 min.), the second step ranges between 760°C and 980°C (18 to 24 min.), and the third covers temperatures above 980°C. Each step is characterized by different chemical reactions. Non-isothermal reduction kinetics equations were set up to describe each step. The kinetics parameters such as apparent activation energies and frequency factors were established. It was found that the first step was chemically controlled, while the second step was diffusion-controlled. Reduction behaviour in the third step was strongly dependent on the initial carbon content in the pellet. Chromium oxide (CrO) could only be reduced in this last step. High temperatures and higher initial carbon content favoured the reduction of CrO.

Jan 1, 2001

By F. E. du Plessis, P. De Waal

Through the development of innovative in-line mineral quantification sensors, the possibility has arisen to apply modern control theory to implement automatic process control for electrostatic high tension (“HT”) roll separators. A pilot-scale set-up was constructed to enable continuous tests to be carried out. A typical dry mill feed was continuously pre-heated and separated with a modern lab scale HT roll machine. The mineralogy as well as mass-flow of the non-conductor stream was quantified in-line, and the combined streams were re-circulated in an endless loop by a combination of vibration feeders and a bucket elevator. A fractional factorial experiment was executed to determine the most significant control parameters of the HT roll separator. Then a multi-input, multi-output dynamic model of the HT electrostatic separator was extracted by the application of standard system identification techniques for automatic control. The most important control variable to ensure a stable product grade could be identified. This allowed a robust single-input, single-output controller to be implemented. The process variable and set-point was mineral grade and the control variable was electrode voltage. Roll speed was manually adjusted while the mineral grade was kept on set-point by the control system. The roll speed, where maximum mass flow and therefore maximum yield was produced on-grade, could therefore be rapidly determined. Atmosphere humidity and ore temperature served as disturbances. Some other adjustable parameters were kept constant during the experiments, namely feed mineralogy, splitter settings and feed rate. Delivery of maximum yield, with a controlled grade, can improve production while reducing the burden of complex manual tuning. Manual tuning previously involved coping with multiple parameters with uncertain cross coupling influences on the end result. Even the end result was typically only known after completion of mineral assays. Automatic grade stabilisation and yield optimisation for a HT roll separator bank requires in-line measurement of mineralogy and mass flow, as well as the implementation of a robust process control system.

Jan 1, 2005

Mining men and State officials in their efforts to make mining safer are confronted from time to time with various complicated questions. In recent gears these questions have tended to increase with the use of mechanical appliances. Twenty-five years ago electricity had been used but little in mires; today there is practically no other means of transmitting power employed in American mines, except that in metal mines compressed air is used, chiefly for drilling and for operating small portable hoists. In coal mines there has been a great increase in mechanization, which tends to concentrate the work of production in small areas and to increase the local difficulties of ventilation; also, it has intensified locally the hazard from coal dust as well as firedamp in bituminous and subbituminous mines. The answers to the questions that arise are not always obvious, as is shown by the fact that even able, experienced men differ in their opinions of the best, way to overcome a particular mining hazard. The difficulty of .solving the problems is also demonstrated by the varying provisions in mine-safety rules, both in official regulations and in the rules of those mining companies that are endeavoring to do more than follow the letter of the law. Such differences of opinion as to the best way of meeting a difficult situation are often found within the same mining organization, and, similarly, varying opinions are held by different members of the Bureau of Mines staff.

Jan 1, 1937

By Winmill T. F.

The previous papers have been concerned only with the atmospheric oxidation of coals from the Barnsley Seam, for which it has been shown that an adequate explanation of the origin and nature of gob-fires can be based on the reaction between the coal itself and the oxygen of the air without the intervention of any other substance. It becomes of importance, therefore, to ascertain how far a similar explanation will hold good for spontaneous heating in other seams, and with this object in view samples including anthracite and lignite have been taken from a considerable number of pits in different parts of the UK (south Wales, Northumberland and Durham, north Staffordshire, Portrush and Ayrshire), some liable to fire, others not. There is abundant evidence to support the commonly-accepted view that spontaneous heating is due to the heat evolved during the absorption of oxygen from the air by coal or pyrites. The quantity of heat produced by the reaction has been measured and it has been shown that the observed rate of heating of a sample of coal agrees with the rate calculated from the heat of reaction and the rate of absorption of oxygen

Dec 1, 1916

By K. B. Nowels

"INTRODUCTION For the last several years the oil industry has been turning more and more toward conservation arid the study of related production problems. It is generally conceded that ultimate recovery is increased by holding the natural gas in thy sand which is net needed in lifting the oil. The retained gas lowers the viscosity and surface tension of the oil and helps flow the oil from the sand. Lewis states that ""while the operator can not control the original conditions of energy and resistance in the sand, he can partly control the efficiency of expulsion. As it is the energy contained in the compressed and absorbed gas rather than the oil that is exhausted, it is but logical to judge the efficiency of a producing method largely by the relative quantities of gas produced with each barrel of oil. If by a change in method the producer lessons the proportion of gas with each barrel of oil, he should increase the total recovery- of oil correspondingly, even if the rate of production is temporarily reduced somewhat.""The effect of ""pinching in"" or controlling the flow of oil wells in an effort to lessen the proportion of has never been definitely known. The general belief has been that ""pinching"" a flowing well causes the oil and gas volumes to be reduced proportionately, maintaining the same gas-oil ratio as before the reduction in flow was made. Studies of gas-oil ratios in many fields have shown that much gas has been wasted, insofar as its effectiveness in oil production is concerned. Swigart and Bopp carried."

Oct 1, 1927

By Andrew J. Petruska, Austin F. Oltmanns

This work proposes a capacitive load cell for conical picks to enable underground continuous mining machine operators to perform their roles away from known hazardous regions near the machine. The load cell is embedded in commercially available flexible printed circuit board, integrates with the target tooling, and demonstrates in situ force sensing of vibration signatures for continuous mining cutting tools. Changes in material constitution, tool mass, and tool geometry cause modal variations in vibrational response measurable with force sensors at the cutting interface. Time-series measurements are captured during rock cutting tests using a linear cutting machine. These measurements are segmented into small windows, less than 0.25 s, and are preprocessed using the fast Fourier transform, which highlights the modal variations. The transformed measurements are then classified into different material and wear categories using support-vector machines with the radial basis function kernel. Different normalization schemes and Fourier transform methods are tested for signal preprocessing. Results show that the power spectral density measurements with normally distributed coefficients give good results for material classification, while the normalized time-domain measurements give better results for wear classification. Under laboratory conditions, this technique is shown to classify material and wear categories with F1 score above 0.85 out of 1.0 for our experiment. This technology could be used to assist operators in assessing material and wear conditions from a safer distance. It has applications in the coal mining industry as well as other applications which use conical picks such as road milling.

Mar 25, 2023

By J. B. Zadra

The use of activated carbon for extracting gold and silver from pregnant cyanide solution and pulp has been investigated many times. The primary advantage of this use of activated carbon is that .the dissolved values can be recovered from slimy ore pulps or from slime portions of ore without settling and thickening or filtering. The loaded carbon is removed from the barren pulp, and the pulp can then be discarded. Activated carbon has been used recently in treating gold ores containing very little soluble silver. When the carbon was loaded with a suitable amount of gold, the silver load was negligible. The remaining problems concerned the removal of the gold from the carbon, the recovery of the gold as bullion, and the reuse of the unloaded carbon. As described in a recent report, a method that solved these problems was developed. The gold-laden carbon was leached with caustic sodium sulfide solution and the gold simultaneously recovered by electrolysis. Both the carbon and the spent solution can be reused. That process was applicable to gold-laden carbon only. It was not applicable to carbon carrying silver, because sodium sulfide does not leach silver from carbon but "fixes" it. It has been necessary, therefore, to develop a modified process for the removal or desorption of both gold and silver from loaded carbon. This modi¬fied process permits the use of activated carbon for extracting both gold and silver from gold ores carrying enough silver to have economical interest or in which silver may be the predominating value.

Jan 1, 1952