Search Documents

By Vinay Kumar, Manis Kumar Jha, J. Rajesh Kumar, Archana Kumari, Rekha Panda, Jin Young Lee

Rare earth metals (REMs) play a significant role in the manufacture of permanent magnets, fluorescent lamps, catalysts, medicines, super alloys etc. Recently, China, which controls 97% of world trade in REMs, imposed restriction on its export. Consequently, the global demand of REMs is escalating and is expected to exceed the supply by 40,000 tonnes annually. Present review paper reports the flow-sheets of commercial processes based on pyro-hydro and hybrid techniques as well as systematic research for process development to recover REMs from primary and secondary resources. This review paper also reports the recommendation and future prospective to fulfill its demand and supply gap keeping in view environmental prospective.

Jan 1, 2014

By G. Guzman, L. Sevilla, M. Botz

"Newmont Mining Corporation operates the Yanacocha mine in Perú and the gold milling section of the property includes a Sulfidization-Acidification-Recycle-Thickening (SART) plant to remove copper from pregnant leach solution. Since its commissioning in 2008, the plant has been intermittently operated as needed to remove copper upstream of a carbon adsorption circuit. However, starting in 2015 Newmont expects the plant to operate on a more continuous basis in response to higher copper ores that will be processed in the gold mill. In anticipation of this, Newmont conducted a campaign in May 2014 with stockpiled high-copper ore to evaluate performance of the SART plant with elevated levels of copper in feed solution. Results from the campaign demonstrated the SART plant is capable of efficiently treating high-copper leach solution. During the campaign, leach solution copper levels ranged from about 100 to 700 mg/L, and copper removals ranging from about 56% to +99% were achieved. The median copper removal efficiency observed during the campaign was about 94%. The primary plant modification determined necessary following the campaign was the need to improve consistency with sulfide dosing. INTRODUCTION Copper removal from cyanide leach solution can be affected through the addition of sulfide at acidic pH to precipitate copper sulfide as a solid. There has been renewed interest in the process in the past several years due to the increasingly common issue of high copper levels in cyanide leach solutions. The term Sulfidization- Acidification-Recycle-Thickening (SART) is used as an acronym for the process according to the primary unit operations utilized. At a pH of approximately 4.0 to 5.0, the addition of soluble sulfide to a copper-bearing leach solution will result in the precipitation of copper sulfide (Cu2S) solid. The overall acidification and sulfidization reaction is (assuming the use of sulfuric acid for pH adjustment): 2Cu(CN)3-2 + 3H2SO4 + S-2 ? Cu2S(s) + 6HCN(aq) + 3SO4-2 The above reaction is written relative to the copper-cyanide complex 2Cu(CN)3-2, though analogous reactions also take place with the other common copper-cyanide complexes Cu(CN)2- and Cu(CN)4-3. Sulfide in the above reaction (S-2) is normally supplied as sodium hydrosulfide (NaHS) purchased in solid or concentrated liquid form. Two characteristics of this reaction that are beneficial to a leaching operation are: 1. Copper is removed from solution as Cu2S (synthetic chalcocite) solid, which can then be sold to a smelter for its copper value. 2. Cyanide that is complexed with copper in the leach solution is released as free cyanide, thereby regenerating cyanide that can be recycled to the leaching operation for continued use."

Jan 1, 2015

By Anderson de Farias Pereira

Estudos recentes sugerem que a produção de nanocompósitos de MgH2 com nanomateriais de morfologia 1D baseados em TiO2 produzidos via moagem reativa promovem aumento significativo na cinética de absorção-dessorção de hidrogênio deste material, o que favoreceria sua aplicação em tecnologias de armazenamento de hidrogênio em estado sólido. A proposta deste trabalho é avaliar o efeito da energia de moagem na integridade das nanopartículas e seu desdobramento nas cinéticas de sorção do material. Para tal, amostras de MgH2 com 5%p. de nanobastões de TiO2 (NR-550) foram produzidas em moinho de bolas planetário a 100, 200 e 300 rpm, respectivamente. Difração de Raios X (DRX) foi utilizada para caracterizar a estrutura cristalina e Microscopia Eletrônica de Transmissão (MET) associada com EDS para analisar o tamanho e morfologia dos catalisadores em meio ao hidreto. Os resultados até o momento indicam que o processo de moagem a 100 rpm não ocasionou variação significativa na distribuição de tamanho e razão de aspecto comparado ao aditivo puro (com valor médio de 35 nm e 2,70 respectivamente). Ensaios de cinética de sorção de hidrogênio ainda estão em andamento.

Oct 30, 2017

By K. C. Dunham, M. Solomon, T. A. Rafter

Sulphur isotope ratios have been determined for 81 sulphides and S and O isotope ratios for 26 barites from the Alston Block in the northern Pennine ore field. In addition, both isotope ratios have been determined for 29 evaporitic anhydrites of various ages from European and Australian localities. The consistency of the sulphate isotope ratios over a wide area of the northern Pennines, and their similarity to values for Lower Carboniferous evaporites, suggests that the sulphate originated from Lower Carboniferous connate waters. It is suggested that these mingled with warm brines rising through granitic plutons beneath Tynehead and Upper Weardale, the aqueous sulphide ion in these brines having a delta34S value of approximately +10 per mille. The delta34S values for the sulphides range from +15.0 to -5.9 per mille and show an outward zoning with higher values in the central fluorite zones and mainly negative values in the outer barite zones. The wide range of delta34S values for the sulphide S is not characteristic of magmatic S and there is no adequate local source in the Carboniferous sediments. It is suggested that formation waters, probably mainly of connate origin, sank down sufficiently deep to become heated above 200°C before rising through Caledonian granite plutons into the Carboniferous sediments, where they spread laterally to mingle with cooler sulphatic connate water. The rising fluids were hypersaline brines carrying F, Ba, Pb, Zn, Cu and S. Temperatures of deposition calculated from galena-sphalerite isotope fractionation are similar to temperatures previously determined from fluid inclusion studies.

Dec 1, 1971

By G. S. Farnham

Abstract This paper lists the interests of the Physical Metallurgy and Chemical Research laboratories of the Metallgesellschaft, which were visited by the authors, members of a group of Canadian investigators sent to Germany by the Department of Reconstruction in 1945. The Physical Metallurgy Research Laboratory The following information was obtained from Professor E. Schmid, Chief of the laboratories. It is understood that Dr. Schmid is a former Nazi and was to be removed from his post in November (1945). Aluminium Research The laboratories investigated the corrosion resistance of the high-strength aluminium-magnesium-zinc alloys. The same test procedure as used by V.L.W. was followed and Dr. Schmid co-operated closely with Dr. Brenner on this project. Intercrystalline corrosion was combatted by additions of chromium, titanium, or vanadium, and the work in this field parallels that of Dr. Brenner of V.L.W. * Dr. Schmid reports that Bollenrath and Siebert believe that corrosion difficulties with these alloys can be overcome to some extent by heat treatment. He himself was of opinion that the correct answer lay not only in correct alloying but also in correct heat treatment. The heat treatment involved either interrupted quenching or a change in quenching rate from a solution temperature of 500°C. The procedure is either a slower cooling from solution temperature or an interrupted cooling with a holding period at l50°C. Work had been done on piston alloys, the 11-13% Si, 1% Ni, 1% Cu, and 1% Mg being the favoured material. This is called Lo-Ex and is similar to Mahle 124 or KS1275.

Jan 1, 1946

By P. J. Noakes

Remote and isolated, located in a frigid, hostile environment, the Black Angel mine in Greenland had to create a warm social environment which would help attract and retain a stable work force of miners and support staff. The high cost of personnel turnover plagues many mines and, when the mine is inside the Arctic Circle, accessible by helicopters which are highly vulnerable to unpredictable weather conditions during the long, dark winters, the potential costs of personnel turnover become critical factors in the success or failure of the mining venture. Manpower planning should start from the date the engineers begin the technical design of the new mine. The plan should include provisions not only to ensure an adequate, skilled work force, but also to ensure a stable work force of people who are happy enough in the mining environment to want to remain, take their vacation and return to work at the mine. The skilled work force was assured with training courses of four months, designed to produce highly specialized underground workers from unskilled Danes and Greenlanders supported by trained Swedish and other Scandinavian miners. The stable social unit was assured by plans the primary attribute of which had to be flexibility. The accommodation changed from shared accommodation with communal washroom facilities to single accommodation with private washroom facilities. A recreational director was hired to help the workers make use of elaborate recreational facilities. A closed-circuit TV and radio system was installed to operate as a private broadcasting system using taped programs originally broadcast on European TV networks or developed by the mine personnel themselves. The liquor rules were changed and the mine manager became a licensed innkeeper responsible for the orderly operation of the Black Angel Bar in accordance with the Danish laws governing the services of a public bar. The result is a relatively stable work force. Some 35% of the people have more than two years' service with the company, Greenex A/S, and some 62% complete 10 months of service.

Jan 1, 1978

By T Preston

Solid Energy is the largest coal producing company in New Zealand, employing 500 people and more than 250 mining contract personnel. The coal produced by Solid Energy plays a significant part in the energy mix for New Zealand being supplied to the coal-fired power station at Huntly. It is also supplied to a wide range of industrial users, NZ Steel, and primary processing. It is fair to say however that the positive economic and social benefits of coal have to some extent been overshadowed by the negative environmental consequences of coal mining.   Over the past two years Solid Energy have been actively researching and addressing the impacts that they currently have on the environment and making a significant investment in environmental improvements, rehabilitation projects and environmental research to address historical and ongoing environmental issues. These investments have been driven by the companyÆs commitment to its environmental policy, which states:   æSolid EnergyÆs overall environmental objective is for the cumulative result of all the activities we undertake to have a positive net effect on the New Zealand environmentÆ.   With such significant investment it is essential that the company is able to target expenditure wisely, ie invest where there is greatest environmental gain to be had, and are also able to actively demonstrate to stakeholders the improvements that are achieved. In order to be able to demonstrate the commitment and the steps that the company is making towards this goal a number of systems have been developed. Firstly an environmental management system along the lines of ISO14001 formalising the environmental processes, responsibilities, auditing and management review. Secondly as part of the planning element of the EMS an environmental management matrix, which allows the scoring of sites against environmental management goals, has been developed. Thirdly the monitoring and measuring tools have been upgraded with GIS driven relational databases installed for management of consent related information and monitoring results.   The development of the environmental management matrix has drawn on a number of existing systems such as the Australian Institute of Mining and Minerals Code 2000. In addition to adapting the scoring regimes from these methods the Solid Energy Environmental Matrix has been further developed to ensure that it reflects the actual environmental impacts on site, as well as the management and audit systems that are in place to control them at a strategic level. The development of this matrix has included a number of steps: +        reviewing the information that stakeholders would be interested in, +        reviewing what was already available, +        development of systems to collect data and benchmark the current         operations, and +        setting up support systems to ensure that the correct information would be provided for scoring.

Jan 1, 2004

By Yi Ran Zhang, Nawoong Yoon, Brent Hilscher, Maria Holuszko

"Ore sorting technology has been rapidly advancing in recent years. Improving expected mill feed grade has a significant benefit to project returns, and can no longer be ignored. When there is an increase in the mill feed grade while maintaining the same throughput, the mine will be able to process much more metal and improve the floatation recovery. There are many more factors that contribute toward the economics of the project by implementing sensor-based sorting technologies covered in this paper. This paper reviews the economic impact on an underground copper-silver deposit with references to the concept of ""profit recovery,"" which is the measurement of recovery based on rock profitability rather than just metal content. The economic impact of sensor-based sorting is discussed in detail throughout the paper. The preliminary economic evaluation of the project compares the mine's base case design versus a design incorporating sensor-based sorting. The paper's primary focus is on economic impacts rather than the explanation of the sensor based sorting results. The sorting data is presented on a scoping level and using a sensor-based sorting study where the best possible results are used for obtaining the grade recovery curves. Also, the breakdown and analysis of the project economics are based on the operating cost available from the particular operation. Any assumptions taken into consideration are also outlined and discussed. INTRODUCTION The mining industry has been adopting Sensor-based ore sorting technology fairly rapidly in the recent years. The ability to increase mill feed grade by rejecting waste grade rocks early in the processing stage is proving to be revolutionary for some operations. These potential outcomes should not be overlooked by both producing operations and prospective projects, thus leading to a wide range of studies on ore sorting. The answer to this is the creation of a new term and concept - Profit Recovery™."

Jan 1, 2018

By O. A. Orumwense

The liberation of intimately disseminated impurities from the coal matrix often demands that the material be ground to a high degree of fineness. Similarly, some technologies for coal utilization require superfine particles (i.e., sizes less than ten microns). This implies additional costs for coal preparation plants due to the high energy and media costs associated with fine grinding operations. Besides, there are problems such as sever product contaminations due to media wear and impairment of the quality of coal. Hence, proper choice of grinding media type is important from the viewpoints of cost reduction and product quality.

Jan 1, 1993

By Witold J. S. Ostrowski

The shaft structure being part of an underground mine, depends on programned functional duties, and on geological and hydrological conditions. The majority of Canadian metal mine shafts are in hard competent igneous rocks, which are in an elastic state of equilibrium around the excavation. Others penetrate soft sedimentary or very weak water-bearing rock formations in which the equilibrium varies from plastic to hydrostatic. Knowledge of how to interpret the underground conditions, determine acting forces and design proper structures is essential for the production and safety of the future mine.

Jan 1, 1973

By N. C. Saxena, S. K. Puri, A. K. Pal

The condition-based monitoring system is an important innovation for reducing the downtime of costly, heavy earth- moving machinery (HEMM). Vibration severity measurements were made on the HEMM located at the Gevra Project, the largest coal opencast project in India. Whenever the vibration severity levels exceeded the permissible limits, necessary actions were taken to replace the defective parts of the ma- chine. The systematic vibration monitoring of 120-t (132-st) dumpers, followed by corrective measures led to a substantial increase in component life (8.18% for an 445E Dressor and 28.44% for an MK-30 Unit Rig). The associated costs (including spareparts) were reduced by 21.55% and 25.74%, respectively. Because of the reduced downtime, savings for these two dumpers over the period from March 26 to June 25,1998, were of the order of Rs.26.47 (US$0.649) million.

Jan 1, 2000

By Gordon Demetrick

3900 Yonge St. was not a typical site on which to build a condominium apartment. A steep hill covered the majority of the site. In order to use as much of this site as possible, the rear of the building was to have nine stores cut into the face of the hill. A permanent shoring system was required as the building structure was not designed to provide sufficient stabilizing elements to support the total earth pressure. The total excavation depth required was 36 m (120'-0") with the upper 12 m (40'-0") to be backsloped. The vertical face of soil to be supported was 24 m (80'-0'). The shoring system originally designed by the Structural Engineer was to support this face by installing soldier piles and inclined earth anchors. During bid preparation it became evident to us that the system as designed would be difficult and expensive to install due to wet soil conditions. An innovative design was required to overcome these problems. Anchor Shoring hired John Stephenson Consultants Ltd. to aid them in accomplishing this goal. After extensive investigation together with The Trow Group, a unique design was proposed which provided a practical solution to the shoring problem.

Jan 1, 1987

By Louis R. Iverson

Patterns of species colonization, biochemical interaction among species, and competitive phenomena were studied in four reclaimed areas in western North Dakota ranging in age from one to four years after mining, along with a site from a native mixed grass prairie for comparison. Early successional changes in floristic composition and soil chemistry were quantified. The mined sites had been contoured, topsoiled, fertilized and seeded. Despite seeding of agronomic species, initial colonization was by fugitive species; analysis of the seed bank in topsoil showed that the most dominant colonizers immigrate after topsoiling. Of the 95 species encountered, Kuchia scoparia was the most dominant in the first two years following mining. Kochlo had relatively low densities in the first year (50-80 plants m-2), but was robust and attained heights of 88 cm with a biomass of about 400 g m-2 In the second year, the plant densities increased to over 10,000 plants m"2 but the height and biomass were reduced to 15 cm and 90 g m-2. However, during the third and fourth years Kochia density declined and was practically non-existent by the fourth year, while the planted Agropyron grasses had concomitantly increased. Other pioneers like Amaran thus retroflexus, Chenopodlum album, Helianthus annuus, Salsola spp. And Setaria spp. showed a less abrupt but similar decline. Chemical analysis of the soils over the same time period showed decreases in electrical conductivity (E.C.), and in the concentrations of P, Ca, Mg, Na, Li, Sr, and SO4 (due to leaching), while N increased. Field studies were conducted on the competitive relations between the dominant species - Kochia scoparia and Agropyron spp. - during early succession. It was found the Kochia acted as a "nurse" crop for several months during the first year of Agropyron spp. establishment, but then began to shade heavily by late July, thus reducing grass tillering. Field and growth chamber experiments on the intraspecific competition relations of Kochia demonstrated that its density and dry matter production, per plant and per unit area, conformed to several laws of plant population biology. Autotoxicity or the depression in growth of a species by its own degradation compounds, in Kochia, appears to be the main factor causing the decline in its growth. Results from a field experiment indicated that thinning dense second year Kochia stands to the density of first year stands did not alter the growth of Kochia, providing strong evidence for autotoxicity. Similarly, several growth chamber experiments demonstrated that small amounts of decaying Kochia leaves and especially roots were toxic to Kochia growth, but not Melilotus officinalis or Agropyron canlnum, Chemical analysis of the soils and plant tissues indicated nutritional im¬balances as shown by P/Mn and P/Zn ratios may be responsible for autotoxicity. In addition to Kochia, a bioassay experiment showed allelochemics to be important in several other colonizing species. Although our results indicate that later stage species generally have greater toxicities than first year colonizers, autotoxicity in the very initial stages seems to be accentuated by harsh habitat conditions. Several practices (mowing. fire, etc.) are used to manage grasslands. Mowing of the first year erect, annual, colonizing vegetation was shown to be beneficial in the growth and establishment of wheatgrasses after mining in western North Dakota. Plots containing Kochio predominantly were mowed in mid-and late-July, and in mid-August, during the first year of growth after recontouring, replacing topsoil. seeding and fertilizing. It was found the Kochia densities were reduced to two percent of the control and its biomass reduced to less than one-third when the area was mowed in mid-August. On the other hand, wheatgrasses showed increases of 23% in stem density and 860% in biomass production over the controls when mowed in mid-August. The mowing of Kochia just before seed-set apparently reduces interspecific competition between Kochia and Agropyron spp. during the following growing season. The method is highly recommended for use in hastening the establishment of planted grasses.

Jan 1, 1982

By F. B. Tough, B. H. Scott

"Petroleum engineering is a comparatively new branch of engineering, with which few people, even petroleum operators and mining engineers, are thoroughly familiar. Petroleum engineers are responsible for the accurate keeping of well logs and all pertinent data upon formations encountered, for the careful analysis of such information, and recommendations as to most suitable places for drilling, for detailed study of methods of drilling, casing, and so on in order to obtain maximum production for a minimum cost.The Bureau of Hines has from time to time carried on work in all branches of petroleum engineering in the various fields of the United States. Such work is also being carried on extensively by the California State Mining Bureau, which has in its employ a number of men who have had, besides their technical training, actual experience in oil field work. This is about the only state at the present time which is carrying on this work in a definite way. It has therefore been the practice of the employees of the Bureau of Mines to go to other states and give such advice and assistance as might prove of value in development work and in prolonging the production of the fields."

Jan 1, 1920

By W. W. Adams

[The s1xteeilth an.nual National Safety C mpeti t1on, concluc ted "by the Bureau of t4ine g, Un+ ~ed st tag' DepartIilent 0:1' the Interior, has jast been closed, and the results reveal t:'W.t. t_!e co~)eting comps.nies had fewer a.ccidents in proportion to the number. of !\1a..."1-h(J1J.l'~ :orkcd than in a:ny other yeex in the record of the contest. These annUk~l contestn are thus achieving the r purpose of promoting safety in tho minin induC'tr:r. ]

Jan 1, 1941

By S. L. Gay

The conventional mass-balance equations used as constraints can lead to flow estimate values of zero even though the flow estimates should be some positive number. This is because many of the constraint equations are satisfied if the flow rates are zero. The way to overcome the problem is to use a slightly different form of the equations. For example, rather than use the conservation of flow of solids as a constraint it is better to use the constraint that the percentage of solids going into a unit equals the percentage of solids coming out of the unit. Examples are given using mineral processing data sets from Mount Isa, Queensland, and Red Dog, Alaska

Jun 21, 1905

By S. M. Runke

"During the past three years the Bureau of Mines has carried on an extensive research program at the Rolla Laboratory for the beneficiation of low-grade Arkansas baixites by ore dressing methods. As a result of this study a 50-ton pilot mill was designed and constructed at Bauxite, Arkansas, by the Bureau to continue the investigation on a semi-commercial scale. The built both to reduce the experimental work to practice and to obtain operating data that cannot be determined by laboratory or small scaleTen samples of bauxitic material were mined and stockpiled at the plant site to ensure an ample supply of material for milling in the pilot plant. These samples were obtained from various bauxite deposits in Saline and Pulaski Counties, Arkansas. The deposits were selected as typical of a wide range of bauxitic material which would necessitate treatment under different conditions and by various concentration methods. All of the samples contained a higher silica content than permissible in Bayer-grade bauxite and several contained so much iron oxide that the available alumina content of the ore was mate¬rially lowered. From data obtained by milling operations on these ten samples, milling characterietics of most of the ores in the district should be predictable. This paper summarizes the results obtained in the laboratory testing of representative samples of each stock pile, and the results of small scale continuous testing of the composite sample of the ten stock piles in the gravity-flotation pilot plant at the Rolla Laboratory."

Aug 1, 1946

By R. C. Troxell

Alternative methods of analyzing data acquired by the Morenci copper concentrator process control instrument-computer system are presented. Experimental measures of ore characteristics, for proposed feed forward control, are introduced. These include on-line indexes of ore hardness, ore density, ore dusting, and ore color. Comparison of metallurgical results before and after computerized process control implementation, allowing for differing ore grades, oxidation, hardness, and fineness of grind, also is described.

Jan 1, 1979

By Thomas C. Denton

In 1965 Africa maintained its position as a region of the world essential to advanced non-Communist nations for supply of vital metals and minerals. The position stemmed from the fact that Africa produced in large quantity a number of key minerals of which either or both resources and production capacity elsewhere did not approach the needs of the free world. The Republic of South Africa alone contributed more than three quarters of the gold mined in the entire non-Communist world besides an estimated 60 percent of metals of the platinum group and the entire new supply of amosite asbestos, and Africa as a whole was nearly the non-Communist world's only source of gem and industrial diamond. Africa also accounted for 83 percent of non-Communist world cobalt production. Besides these massive contributions, Africa in 1965 provided 50 percent or more of the new supply from non-Communist countries of the following mineral commodities: Lithium minerals, corundum, manganese ore: and chromite, and over 20 percent of new supply from non-Communist countries of columbium-tantalum concentrates, antimony, beryl, vanadium, phosphate rock, and copper. Africa also accounted for 18 percent of the non-Communist world's output of uranium, 14 percent of its tin, 11 percent of its lead, 9 percent of its zinc, and 8.9 percent of its crude oil output. With respect to chromite, at yearend Africa's reserves of the mineral were far larger than those of all other non-Communist regions combined. This probably also held true for manganese ore. In the case of crude oil, the fact that Africa's share of non-Communist world output was 1.6 percentage points greater than in 1964 was significant, particularly inasmuch as the output rate was continuing to increase at yearend.

Jan 1, 1967

By E. Açma

Sivas-Divrigi flotation plant has a capacity of 90,000 tpy. Beneficiation of the tailings of iron ore magnetic separator seems to be attractive, because of its Cu, Co, and Ni contents. In the experimental work, sulfidic flotation concentrate is produced from these tailings. A roasting-leaching-H2S precipitation procedure is used to treat this concentrate, containing 0.55% Cu, 0.51% Co, 0.74% Ni, and 0.027% Zn. Sulfatizing roasting is carried out in a rotary furnace at 690°C. Roasted product is leached with 10 gpl HzSOl at 70°C and 30% pulp density. For the precipitation of desired metal, H2S is bubbled through the concentrated solution of repeated leaching, under controlled temperature and pH. Final metal recoveries of 91% Cu, 91% Co, and 50% Ni, and 92% Zn are attained. Roasting gases with their 13% SO2 content are suitable for H2SO4 production and the leach residues can be integrated with the iron ore processing plant as they contain 57.4% Fe and very low non-ferrous metals.

Jan 1, 1993